1 /* sh-stub.c -- debugging stub for the Renesas-SH.
2
3 NOTE!! This code has to be compiled with optimization, otherwise the
4 function inlining which generates the exception handlers won't work.
5
6 */
7
8 /* This is originally based on an m68k software stub written by Glenn
9 Engel at HP, but has changed quite a bit.
10
11 Modifications for the SH by Ben Lee and Steve Chamberlain
12
13 */
14
15 /****************************************************************************
16
17 THIS SOFTWARE IS NOT COPYRIGHTED
18
19 HP offers the following for use in the public domain. HP makes no
20 warranty with regard to the software or it's performance and the
21 user accepts the software "AS IS" with all faults.
22
23 HP DISCLAIMS ANY WARRANTIES, EXPRESS OR IMPLIED, WITH REGARD
24 TO THIS SOFTWARE INCLUDING BUT NOT LIMITED TO THE WARRANTIES
25 OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
26
27 ****************************************************************************/
28
29
30 /* Remote communication protocol.
31
32 A debug packet whose contents are <data>
33 is encapsulated for transmission in the form:
34
35 $ <data> # CSUM1 CSUM2
36
37 <data> must be ASCII alphanumeric and cannot include characters
38 '$' or '#'. If <data> starts with two characters followed by
39 ':', then the existing stubs interpret this as a sequence number.
40
41 CSUM1 and CSUM2 are ascii hex representation of an 8-bit
42 checksum of <data>, the most significant nibble is sent first.
43 the hex digits 0-9,a-f are used.
44
45 Receiver responds with:
46
47 + - if CSUM is correct and ready for next packet
48 - - if CSUM is incorrect
49
50 <data> is as follows:
51 All values are encoded in ascii hex digits.
52
53 Request Packet
54
55 read registers g
56 reply XX....X Each byte of register data
57 is described by two hex digits.
58 Registers are in the internal order
59 for GDB, and the bytes in a register
60 are in the same order the machine uses.
61 or ENN for an error.
62
63 write regs GXX..XX Each byte of register data
64 is described by two hex digits.
65 reply OK for success
66 ENN for an error
67
68 write reg Pn...=r... Write register n... with value r...,
69 which contains two hex digits for each
70 byte in the register (target byte
71 order).
72 reply OK for success
73 ENN for an error
74 (not supported by all stubs).
75
76 read mem mAA..AA,LLLL AA..AA is address, LLLL is length.
77 reply XX..XX XX..XX is mem contents
78 Can be fewer bytes than requested
79 if able to read only part of the data.
80 or ENN NN is errno
81
82 write mem MAA..AA,LLLL:XX..XX
83 AA..AA is address,
84 LLLL is number of bytes,
85 XX..XX is data
86 reply OK for success
87 ENN for an error (this includes the case
88 where only part of the data was
89 written).
90
91 cont cAA..AA AA..AA is address to resume
92 If AA..AA is omitted,
93 resume at same address.
94
95 step sAA..AA AA..AA is address to resume
96 If AA..AA is omitted,
97 resume at same address.
98
99 last signal ? Reply the current reason for stopping.
100 This is the same reply as is generated
101 for step or cont : SAA where AA is the
102 signal number.
103
104 There is no immediate reply to step or cont.
105 The reply comes when the machine stops.
106 It is SAA AA is the "signal number"
107
108 or... TAAn...:r...;n:r...;n...:r...;
109 AA = signal number
110 n... = register number
111 r... = register contents
112 or... WAA The process exited, and AA is
113 the exit status. This is only
114 applicable for certains sorts of
115 targets.
116 kill request k
117
118 toggle debug d toggle debug flag (see 386 & 68k stubs)
119 reset r reset -- see sparc stub.
120 reserved <other> On other requests, the stub should
121 ignore the request and send an empty
122 response ($#<checksum>). This way
123 we can extend the protocol and GDB
124 can tell whether the stub it is
125 talking to uses the old or the new.
126 search tAA:PP,MM Search backwards starting at address
127 AA for a match with pattern PP and
128 mask MM. PP and MM are 4 bytes.
129 Not supported by all stubs.
130
131 general query qXXXX Request info about XXXX.
132 general set QXXXX=yyyy Set value of XXXX to yyyy.
133 query sect offs qOffsets Get section offsets. Reply is
134 Text=xxx;Data=yyy;Bss=zzz
135 console output Otext Send text to stdout. Only comes from
136 remote target.
137
138 Responses can be run-length encoded to save space. A '*' means that
139 the next character is an ASCII encoding giving a repeat count which
140 stands for that many repititions of the character preceding the '*'.
141 The encoding is n+29, yielding a printable character where n >=3
142 (which is where rle starts to win). Don't use an n > 126.
143
144 So
145 "0* " means the same as "0000". */
146
147 #include <string.h>
148 #include <setjmp.h>
149
150 /* Renesas SH architecture instruction encoding masks */
151
152 #define COND_BR_MASK 0xff00
153 #define UCOND_DBR_MASK 0xe000
154 #define UCOND_RBR_MASK 0xf0df
155 #define TRAPA_MASK 0xff00
156
157 #define COND_DISP 0x00ff
158 #define UCOND_DISP 0x0fff
159 #define UCOND_REG 0x0f00
160
161 /* Renesas SH instruction opcodes */
162
163 #define BF_INSTR 0x8b00
164 #define BT_INSTR 0x8900
165 #define BRA_INSTR 0xa000
166 #define BSR_INSTR 0xb000
167 #define JMP_INSTR 0x402b
168 #define JSR_INSTR 0x400b
169 #define RTS_INSTR 0x000b
170 #define RTE_INSTR 0x002b
171 #define TRAPA_INSTR 0xc300
172 #define SSTEP_INSTR 0xc3ff
173
174 /* Renesas SH processor register masks */
175
176 #define T_BIT_MASK 0x0001
177
178 /*
179 * BUFMAX defines the maximum number of characters in inbound/outbound
180 * buffers. At least NUMREGBYTES*2 are needed for register packets.
181 */
182 #define BUFMAX 1024
183
184 /*
185 * Number of bytes for registers
186 */
187 #define NUMREGBYTES 112 /* 92 */
188
189 /*
190 * typedef
191 */
192 typedef void (*Function) ();
193
194 /*
195 * Forward declarations
196 */
197
198 static int hex (char);
199 static char *mem2hex (char *, char *, int);
200 static char *hex2mem (char *, char *, int);
201 static int hexToInt (char **, int *);
202 static unsigned char *getpacket (void);
203 static void putpacket (char *);
204 static void handle_buserror (void);
205 static int computeSignal (int exceptionVector);
206 static void handle_exception (int exceptionVector);
207 void init_serial();
208
209 void putDebugChar (char);
210 char getDebugChar (void);
211
212 /* These are in the file but in asm statements so the compiler can't see them */
213 void catch_exception_4 (void);
214 void catch_exception_6 (void);
215 void catch_exception_9 (void);
216 void catch_exception_10 (void);
217 void catch_exception_11 (void);
218 void catch_exception_32 (void);
219 void catch_exception_33 (void);
220 void catch_exception_255 (void);
221
222
223
224 #define catch_exception_random catch_exception_255 /* Treat all odd ones like 255 */
225
226 void breakpoint (void);
227
228
229 #define init_stack_size 8*1024 /* if you change this you should also modify BINIT */
230 #define stub_stack_size 8*1024
231
232 int init_stack[init_stack_size] __attribute__ ((section ("stack"))) = {0};
233 int stub_stack[stub_stack_size] __attribute__ ((section ("stack"))) = {0};
234
235
236 void INIT ();
237 void BINIT ();
238
239 #define CPU_BUS_ERROR_VEC 9
240 #define DMA_BUS_ERROR_VEC 10
241 #define NMI_VEC 11
242 #define INVALID_INSN_VEC 4
243 #define INVALID_SLOT_VEC 6
244 #define TRAP_VEC 32
245 #define IO_VEC 33
246 #define USER_VEC 255
247
248
249
250 char in_nmi; /* Set when handling an NMI, so we don't reenter */
251 int dofault; /* Non zero, bus errors will raise exception */
252
253 int *stub_sp;
254
255 /* debug > 0 prints ill-formed commands in valid packets & checksum errors */
256 int remote_debug;
257
258 /* jump buffer used for setjmp/longjmp */
259 jmp_buf remcomEnv;
260
261 enum regnames
262 {
263 R0, R1, R2, R3, R4, R5, R6, R7,
264 R8, R9, R10, R11, R12, R13, R14,
265 R15, PC, PR, GBR, VBR, MACH, MACL, SR,
266 TICKS, STALLS, CYCLES, INSTS, PLR
267 };
268
269 typedef struct
270 {
271 short *memAddr;
272 short oldInstr;
273 }
274 stepData;
275
276 int registers[NUMREGBYTES / 4];
277 stepData instrBuffer;
278 char stepped;
279 static const char hexchars[] = "0123456789abcdef";
280 static char remcomInBuffer[BUFMAX];
281 static char remcomOutBuffer[BUFMAX];
282
highhex(int x)283 char highhex(int x)
284 {
285 return hexchars[(x >> 4) & 0xf];
286 }
287
lowhex(int x)288 char lowhex(int x)
289 {
290 return hexchars[x & 0xf];
291 }
292
293 /*
294 * Assembly macros
295 */
296
297 #define BREAKPOINT() asm("trapa #0x20"::);
298
299
300 /*
301 * Routines to handle hex data
302 */
303
304 static int
hex(char ch)305 hex (char ch)
306 {
307 if ((ch >= 'a') && (ch <= 'f'))
308 return (ch - 'a' + 10);
309 if ((ch >= '0') && (ch <= '9'))
310 return (ch - '0');
311 if ((ch >= 'A') && (ch <= 'F'))
312 return (ch - 'A' + 10);
313 return (-1);
314 }
315
316 /* convert the memory, pointed to by mem into hex, placing result in buf */
317 /* return a pointer to the last char put in buf (null) */
318 static char *
mem2hex(char * mem,char * buf,int count)319 mem2hex (char *mem, char *buf, int count)
320 {
321 int i;
322 int ch;
323 for (i = 0; i < count; i++)
324 {
325 ch = *mem++;
326 *buf++ = highhex (ch);
327 *buf++ = lowhex (ch);
328 }
329 *buf = 0;
330 return (buf);
331 }
332
333 /* convert the hex array pointed to by buf into binary, to be placed in mem */
334 /* return a pointer to the character after the last byte written */
335
336 static char *
hex2mem(char * buf,char * mem,int count)337 hex2mem (char *buf, char *mem, int count)
338 {
339 int i;
340 unsigned char ch;
341 for (i = 0; i < count; i++)
342 {
343 ch = hex (*buf++) << 4;
344 ch = ch + hex (*buf++);
345 *mem++ = ch;
346 }
347 return (mem);
348 }
349
350 /**********************************************/
351 /* WHILE WE FIND NICE HEX CHARS, BUILD AN INT */
352 /* RETURN NUMBER OF CHARS PROCESSED */
353 /**********************************************/
354 static int
hexToInt(char ** ptr,int * intValue)355 hexToInt (char **ptr, int *intValue)
356 {
357 int numChars = 0;
358 int hexValue;
359
360 *intValue = 0;
361
362 while (**ptr)
363 {
364 hexValue = hex (**ptr);
365 if (hexValue >= 0)
366 {
367 *intValue = (*intValue << 4) | hexValue;
368 numChars++;
369 }
370 else
371 break;
372
373 (*ptr)++;
374 }
375
376 return (numChars);
377 }
378
379 /*
380 * Routines to get and put packets
381 */
382
383 /* scan for the sequence $<data>#<checksum> */
384
385 char *
getpacket(void)386 getpacket (void)
387 {
388 unsigned char *buffer = &remcomInBuffer[0];
389 unsigned char checksum;
390 unsigned char xmitcsum;
391 int count;
392 char ch;
393
394 while (1)
395 {
396 /* wait around for the start character, ignore all other characters */
397 while ((ch = getDebugChar ()) != '$')
398 ;
399
400 retry:
401 checksum = 0;
402 xmitcsum = -1;
403 count = 0;
404
405 /* now, read until a # or end of buffer is found */
406 while (count < BUFMAX - 1)
407 {
408 ch = getDebugChar ();
409 if (ch == '$')
410 goto retry;
411 if (ch == '#')
412 break;
413 checksum = checksum + ch;
414 buffer[count] = ch;
415 count = count + 1;
416 }
417 buffer[count] = 0;
418
419 if (ch == '#')
420 {
421 ch = getDebugChar ();
422 xmitcsum = hex (ch) << 4;
423 ch = getDebugChar ();
424 xmitcsum += hex (ch);
425
426 if (checksum != xmitcsum)
427 {
428 putDebugChar ('-'); /* failed checksum */
429 }
430 else
431 {
432 putDebugChar ('+'); /* successful transfer */
433
434 /* if a sequence char is present, reply the sequence ID */
435 if (buffer[2] == ':')
436 {
437 putDebugChar (buffer[0]);
438 putDebugChar (buffer[1]);
439
440 return &buffer[3];
441 }
442
443 return &buffer[0];
444 }
445 }
446 }
447 }
448
449
450 /* send the packet in buffer. */
451
452 static void
putpacket(char * buffer)453 putpacket (char *buffer)
454 {
455 int checksum;
456 int count;
457
458 /* $<packet info>#<checksum>. */
459 do
460 {
461 char *src = buffer;
462 putDebugChar ('$');
463 checksum = 0;
464
465 while (*src)
466 {
467 int runlen;
468
469 /* Do run length encoding */
470 for (runlen = 0; runlen < 100; runlen ++)
471 {
472 if (src[0] != src[runlen])
473 {
474 if (runlen > 3)
475 {
476 int encode;
477 /* Got a useful amount */
478 putDebugChar (*src);
479 checksum += *src;
480 putDebugChar ('*');
481 checksum += '*';
482 checksum += (encode = runlen + ' ' - 4);
483 putDebugChar (encode);
484 src += runlen;
485 }
486 else
487 {
488 putDebugChar (*src);
489 checksum += *src;
490 src++;
491 }
492 break;
493 }
494 }
495 }
496
497
498 putDebugChar ('#');
499 putDebugChar (highhex(checksum));
500 putDebugChar (lowhex(checksum));
501 }
502 while (getDebugChar() != '+');
503 }
504
505
506 /* a bus error has occurred, perform a longjmp
507 to return execution and allow handling of the error */
508
509 void
handle_buserror(void)510 handle_buserror (void)
511 {
512 longjmp (remcomEnv, 1);
513 }
514
515 /*
516 * this function takes the SH-1 exception number and attempts to
517 * translate this number into a unix compatible signal value
518 */
519 static int
computeSignal(int exceptionVector)520 computeSignal (int exceptionVector)
521 {
522 int sigval;
523 switch (exceptionVector)
524 {
525 case INVALID_INSN_VEC:
526 sigval = 4;
527 break;
528 case INVALID_SLOT_VEC:
529 sigval = 4;
530 break;
531 case CPU_BUS_ERROR_VEC:
532 sigval = 10;
533 break;
534 case DMA_BUS_ERROR_VEC:
535 sigval = 10;
536 break;
537 case NMI_VEC:
538 sigval = 2;
539 break;
540
541 case TRAP_VEC:
542 case USER_VEC:
543 sigval = 5;
544 break;
545
546 default:
547 sigval = 7; /* "software generated"*/
548 break;
549 }
550 return (sigval);
551 }
552
553 void
doSStep(void)554 doSStep (void)
555 {
556 short *instrMem;
557 int displacement;
558 int reg;
559 unsigned short opcode;
560
561 instrMem = (short *) registers[PC];
562
563 opcode = *instrMem;
564 stepped = 1;
565
566 if ((opcode & COND_BR_MASK) == BT_INSTR)
567 {
568 if (registers[SR] & T_BIT_MASK)
569 {
570 displacement = (opcode & COND_DISP) << 1;
571 if (displacement & 0x80)
572 displacement |= 0xffffff00;
573 /*
574 * Remember PC points to second instr.
575 * after PC of branch ... so add 4
576 */
577 instrMem = (short *) (registers[PC] + displacement + 4);
578 }
579 else
580 instrMem += 1;
581 }
582 else if ((opcode & COND_BR_MASK) == BF_INSTR)
583 {
584 if (registers[SR] & T_BIT_MASK)
585 instrMem += 1;
586 else
587 {
588 displacement = (opcode & COND_DISP) << 1;
589 if (displacement & 0x80)
590 displacement |= 0xffffff00;
591 /*
592 * Remember PC points to second instr.
593 * after PC of branch ... so add 4
594 */
595 instrMem = (short *) (registers[PC] + displacement + 4);
596 }
597 }
598 else if ((opcode & UCOND_DBR_MASK) == BRA_INSTR)
599 {
600 displacement = (opcode & UCOND_DISP) << 1;
601 if (displacement & 0x0800)
602 displacement |= 0xfffff000;
603
604 /*
605 * Remember PC points to second instr.
606 * after PC of branch ... so add 4
607 */
608 instrMem = (short *) (registers[PC] + displacement + 4);
609 }
610 else if ((opcode & UCOND_RBR_MASK) == JSR_INSTR)
611 {
612 reg = (char) ((opcode & UCOND_REG) >> 8);
613
614 instrMem = (short *) registers[reg];
615 }
616 else if (opcode == RTS_INSTR)
617 instrMem = (short *) registers[PR];
618 else if (opcode == RTE_INSTR)
619 instrMem = (short *) registers[15];
620 else if ((opcode & TRAPA_MASK) == TRAPA_INSTR)
621 instrMem = (short *) ((opcode & ~TRAPA_MASK) << 2);
622 else
623 instrMem += 1;
624
625 instrBuffer.memAddr = instrMem;
626 instrBuffer.oldInstr = *instrMem;
627 *instrMem = SSTEP_INSTR;
628 }
629
630
631 /* Undo the effect of a previous doSStep. If we single stepped,
632 restore the old instruction. */
633
634 void
undoSStep(void)635 undoSStep (void)
636 {
637 if (stepped)
638 { short *instrMem;
639 instrMem = instrBuffer.memAddr;
640 *instrMem = instrBuffer.oldInstr;
641 }
642 stepped = 0;
643 }
644
645 /*
646 This function does all exception handling. It only does two things -
647 it figures out why it was called and tells gdb, and then it reacts
648 to gdb's requests.
649
650 When in the monitor mode we talk a human on the serial line rather than gdb.
651
652 */
653
654
655 void
gdb_handle_exception(int exceptionVector)656 gdb_handle_exception (int exceptionVector)
657 {
658 int sigval, stepping;
659 int addr, length;
660 char *ptr;
661
662 /* reply to host that an exception has occurred */
663 sigval = computeSignal (exceptionVector);
664 remcomOutBuffer[0] = 'S';
665 remcomOutBuffer[1] = highhex(sigval);
666 remcomOutBuffer[2] = lowhex (sigval);
667 remcomOutBuffer[3] = 0;
668
669 putpacket (remcomOutBuffer);
670
671 /*
672 * exception 255 indicates a software trap
673 * inserted in place of code ... so back up
674 * PC by one instruction, since this instruction
675 * will later be replaced by its original one!
676 */
677 if (exceptionVector == 0xff
678 || exceptionVector == 0x20)
679 registers[PC] -= 2;
680
681 /*
682 * Do the thangs needed to undo
683 * any stepping we may have done!
684 */
685 undoSStep ();
686
687 stepping = 0;
688
689 while (1)
690 {
691 remcomOutBuffer[0] = 0;
692 ptr = getpacket ();
693
694 switch (*ptr++)
695 {
696 case '?':
697 remcomOutBuffer[0] = 'S';
698 remcomOutBuffer[1] = highhex (sigval);
699 remcomOutBuffer[2] = lowhex (sigval);
700 remcomOutBuffer[3] = 0;
701 break;
702 case 'd':
703 remote_debug = !(remote_debug); /* toggle debug flag */
704 break;
705 case 'g': /* return the value of the CPU registers */
706 mem2hex ((char *) registers, remcomOutBuffer, NUMREGBYTES);
707 break;
708 case 'G': /* set the value of the CPU registers - return OK */
709 hex2mem (ptr, (char *) registers, NUMREGBYTES);
710 strcpy (remcomOutBuffer, "OK");
711 break;
712
713 /* mAA..AA,LLLL Read LLLL bytes at address AA..AA */
714 case 'm':
715 if (setjmp (remcomEnv) == 0)
716 {
717 dofault = 0;
718 /* TRY, TO READ %x,%x. IF SUCCEED, SET PTR = 0 */
719 if (hexToInt (&ptr, &addr))
720 if (*(ptr++) == ',')
721 if (hexToInt (&ptr, &length))
722 {
723 ptr = 0;
724 mem2hex ((char *) addr, remcomOutBuffer, length);
725 }
726 if (ptr)
727 strcpy (remcomOutBuffer, "E01");
728 }
729 else
730 strcpy (remcomOutBuffer, "E03");
731
732 /* restore handler for bus error */
733 dofault = 1;
734 break;
735
736 /* MAA..AA,LLLL: Write LLLL bytes at address AA.AA return OK */
737 case 'M':
738 if (setjmp (remcomEnv) == 0)
739 {
740 dofault = 0;
741
742 /* TRY, TO READ '%x,%x:'. IF SUCCEED, SET PTR = 0 */
743 if (hexToInt (&ptr, &addr))
744 if (*(ptr++) == ',')
745 if (hexToInt (&ptr, &length))
746 if (*(ptr++) == ':')
747 {
748 hex2mem (ptr, (char *) addr, length);
749 ptr = 0;
750 strcpy (remcomOutBuffer, "OK");
751 }
752 if (ptr)
753 strcpy (remcomOutBuffer, "E02");
754 }
755 else
756 strcpy (remcomOutBuffer, "E03");
757
758 /* restore handler for bus error */
759 dofault = 1;
760 break;
761
762 /* cAA..AA Continue at address AA..AA(optional) */
763 /* sAA..AA Step one instruction from AA..AA(optional) */
764 case 's':
765 stepping = 1;
766 case 'c':
767 {
768 /* tRY, to read optional parameter, pc unchanged if no parm */
769 if (hexToInt (&ptr, &addr))
770 registers[PC] = addr;
771
772 if (stepping)
773 doSStep ();
774 }
775 return;
776 break;
777
778 /* kill the program */
779 case 'k': /* do nothing */
780 break;
781 } /* switch */
782
783 /* reply to the request */
784 putpacket (remcomOutBuffer);
785 }
786 }
787
788
789 #define GDBCOOKIE 0x5ac
790 static int ingdbmode;
791 /* We've had an exception - choose to go into the monitor or
792 the gdb stub */
handle_exception(int exceptionVector)793 void handle_exception(int exceptionVector)
794 {
795 #ifdef MONITOR
796 if (ingdbmode != GDBCOOKIE)
797 monitor_handle_exception (exceptionVector);
798 else
799 #endif
800 gdb_handle_exception (exceptionVector);
801
802 }
803
804 void
gdb_mode(void)805 gdb_mode (void)
806 {
807 ingdbmode = GDBCOOKIE;
808 breakpoint();
809 }
810 /* This function will generate a breakpoint exception. It is used at the
811 beginning of a program to sync up with a debugger and can be used
812 otherwise as a quick means to stop program execution and "break" into
813 the debugger. */
814
815 void
breakpoint(void)816 breakpoint (void)
817 {
818 BREAKPOINT ();
819 }
820
821 /**** Processor-specific routines start here ****/
822 /**** Processor-specific routines start here ****/
823 /**** Processor-specific routines start here ****/
824
825 /* Note:
826
827 The Renesas SH family uses two exception architectures:
828
829 SH1 & SH2:
830
831 These processors utilize an exception vector table.
832 Exceptions are vectored to the address stored at VBR + (exception_num * 4)
833
834 SH3, SH3E, & SH4:
835
836 These processors have fixed entry points relative to the VBR for
837 various exception classes.
838 */
839
840 #if defined(__sh1__) || defined(__sh2__)
841
842 /* SH1/SH2 exception vector table format */
843
844 typedef struct
845 {
846 void (*func_cold) ();
847 int *stack_cold;
848 void (*func_warm) ();
849 int *stack_warm;
850 void (*(handler[256 - 4])) ();
851 }
852 vec_type;
853
854 /* vectable is the SH1/SH2 vector table. It must be at address 0
855 or wherever your vbr points. */
856
857 const vec_type vectable =
858 {
859 &BINIT, /* 0: Power-on reset PC */
860 init_stack + init_stack_size, /* 1: Power-on reset SP */
861 &BINIT, /* 2: Manual reset PC */
862 init_stack + init_stack_size, /* 3: Manual reset SP */
863 {
864 &catch_exception_4, /* 4: General invalid instruction */
865 &catch_exception_random, /* 5: Reserved for system */
866 &catch_exception_6, /* 6: Invalid slot instruction */
867 &catch_exception_random, /* 7: Reserved for system */
868 &catch_exception_random, /* 8: Reserved for system */
869 &catch_exception_9, /* 9: CPU bus error */
870 &catch_exception_10, /* 10: DMA bus error */
871 &catch_exception_11, /* 11: NMI */
872 &catch_exception_random, /* 12: User break */
873 &catch_exception_random, /* 13: Reserved for system */
874 &catch_exception_random, /* 14: Reserved for system */
875 &catch_exception_random, /* 15: Reserved for system */
876 &catch_exception_random, /* 16: Reserved for system */
877 &catch_exception_random, /* 17: Reserved for system */
878 &catch_exception_random, /* 18: Reserved for system */
879 &catch_exception_random, /* 19: Reserved for system */
880 &catch_exception_random, /* 20: Reserved for system */
881 &catch_exception_random, /* 21: Reserved for system */
882 &catch_exception_random, /* 22: Reserved for system */
883 &catch_exception_random, /* 23: Reserved for system */
884 &catch_exception_random, /* 24: Reserved for system */
885 &catch_exception_random, /* 25: Reserved for system */
886 &catch_exception_random, /* 26: Reserved for system */
887 &catch_exception_random, /* 27: Reserved for system */
888 &catch_exception_random, /* 28: Reserved for system */
889 &catch_exception_random, /* 29: Reserved for system */
890 &catch_exception_random, /* 30: Reserved for system */
891 &catch_exception_random, /* 31: Reserved for system */
892 &catch_exception_32, /* 32: Trap instr (user vectors) */
893 &catch_exception_33, /* 33: Trap instr (user vectors) */
894 &catch_exception_random, /* 34: Trap instr (user vectors) */
895 &catch_exception_random, /* 35: Trap instr (user vectors) */
896 &catch_exception_random, /* 36: Trap instr (user vectors) */
897 &catch_exception_random, /* 37: Trap instr (user vectors) */
898 &catch_exception_random, /* 38: Trap instr (user vectors) */
899 &catch_exception_random, /* 39: Trap instr (user vectors) */
900 &catch_exception_random, /* 40: Trap instr (user vectors) */
901 &catch_exception_random, /* 41: Trap instr (user vectors) */
902 &catch_exception_random, /* 42: Trap instr (user vectors) */
903 &catch_exception_random, /* 43: Trap instr (user vectors) */
904 &catch_exception_random, /* 44: Trap instr (user vectors) */
905 &catch_exception_random, /* 45: Trap instr (user vectors) */
906 &catch_exception_random, /* 46: Trap instr (user vectors) */
907 &catch_exception_random, /* 47: Trap instr (user vectors) */
908 &catch_exception_random, /* 48: Trap instr (user vectors) */
909 &catch_exception_random, /* 49: Trap instr (user vectors) */
910 &catch_exception_random, /* 50: Trap instr (user vectors) */
911 &catch_exception_random, /* 51: Trap instr (user vectors) */
912 &catch_exception_random, /* 52: Trap instr (user vectors) */
913 &catch_exception_random, /* 53: Trap instr (user vectors) */
914 &catch_exception_random, /* 54: Trap instr (user vectors) */
915 &catch_exception_random, /* 55: Trap instr (user vectors) */
916 &catch_exception_random, /* 56: Trap instr (user vectors) */
917 &catch_exception_random, /* 57: Trap instr (user vectors) */
918 &catch_exception_random, /* 58: Trap instr (user vectors) */
919 &catch_exception_random, /* 59: Trap instr (user vectors) */
920 &catch_exception_random, /* 60: Trap instr (user vectors) */
921 &catch_exception_random, /* 61: Trap instr (user vectors) */
922 &catch_exception_random, /* 62: Trap instr (user vectors) */
923 &catch_exception_random, /* 63: Trap instr (user vectors) */
924 &catch_exception_random, /* 64: IRQ0 */
925 &catch_exception_random, /* 65: IRQ1 */
926 &catch_exception_random, /* 66: IRQ2 */
927 &catch_exception_random, /* 67: IRQ3 */
928 &catch_exception_random, /* 68: IRQ4 */
929 &catch_exception_random, /* 69: IRQ5 */
930 &catch_exception_random, /* 70: IRQ6 */
931 &catch_exception_random, /* 71: IRQ7 */
932 &catch_exception_random,
933 &catch_exception_random,
934 &catch_exception_random,
935 &catch_exception_random,
936 &catch_exception_random,
937 &catch_exception_random,
938 &catch_exception_random,
939 &catch_exception_random,
940 &catch_exception_random,
941 &catch_exception_random,
942 &catch_exception_random,
943 &catch_exception_random,
944 &catch_exception_random,
945 &catch_exception_random,
946 &catch_exception_random,
947 &catch_exception_random,
948 &catch_exception_random,
949 &catch_exception_random,
950 &catch_exception_random,
951 &catch_exception_random,
952 &catch_exception_random,
953 &catch_exception_random,
954 &catch_exception_random,
955 &catch_exception_random,
956 &catch_exception_random,
957 &catch_exception_random,
958 &catch_exception_random,
959 &catch_exception_random,
960 &catch_exception_random,
961 &catch_exception_random,
962 &catch_exception_random,
963 &catch_exception_random,
964 &catch_exception_random,
965 &catch_exception_random,
966 &catch_exception_random,
967 &catch_exception_random,
968 &catch_exception_random,
969 &catch_exception_random,
970 &catch_exception_random,
971 &catch_exception_random,
972 &catch_exception_random,
973 &catch_exception_random,
974 &catch_exception_random,
975 &catch_exception_random,
976 &catch_exception_random,
977 &catch_exception_random,
978 &catch_exception_random,
979 &catch_exception_random,
980 &catch_exception_random,
981 &catch_exception_random,
982 &catch_exception_random,
983 &catch_exception_random,
984 &catch_exception_random,
985 &catch_exception_random,
986 &catch_exception_random,
987 &catch_exception_random,
988 &catch_exception_random,
989 &catch_exception_random,
990 &catch_exception_random,
991 &catch_exception_random,
992 &catch_exception_random,
993 &catch_exception_random,
994 &catch_exception_random,
995 &catch_exception_random,
996 &catch_exception_random,
997 &catch_exception_random,
998 &catch_exception_random,
999 &catch_exception_random,
1000 &catch_exception_random,
1001 &catch_exception_random,
1002 &catch_exception_random,
1003 &catch_exception_random,
1004 &catch_exception_random,
1005 &catch_exception_random,
1006 &catch_exception_random,
1007 &catch_exception_random,
1008 &catch_exception_random,
1009 &catch_exception_random,
1010 &catch_exception_random,
1011 &catch_exception_random,
1012 &catch_exception_random,
1013 &catch_exception_random,
1014 &catch_exception_random,
1015 &catch_exception_random,
1016 &catch_exception_random,
1017 &catch_exception_random,
1018 &catch_exception_random,
1019 &catch_exception_random,
1020 &catch_exception_random,
1021 &catch_exception_random,
1022 &catch_exception_random,
1023 &catch_exception_random,
1024 &catch_exception_random,
1025 &catch_exception_random,
1026 &catch_exception_random,
1027 &catch_exception_random,
1028 &catch_exception_random,
1029 &catch_exception_random,
1030 &catch_exception_random,
1031 &catch_exception_random,
1032 &catch_exception_random,
1033 &catch_exception_random,
1034 &catch_exception_random,
1035 &catch_exception_random,
1036 &catch_exception_random,
1037 &catch_exception_random,
1038 &catch_exception_random,
1039 &catch_exception_random,
1040 &catch_exception_random,
1041 &catch_exception_random,
1042 &catch_exception_random,
1043 &catch_exception_random,
1044 &catch_exception_random,
1045 &catch_exception_random,
1046 &catch_exception_random,
1047 &catch_exception_random,
1048 &catch_exception_random,
1049 &catch_exception_random,
1050 &catch_exception_random,
1051 &catch_exception_random,
1052 &catch_exception_random,
1053 &catch_exception_random,
1054 &catch_exception_random,
1055 &catch_exception_random,
1056 &catch_exception_random,
1057 &catch_exception_random,
1058 &catch_exception_random,
1059 &catch_exception_random,
1060 &catch_exception_random,
1061 &catch_exception_random,
1062 &catch_exception_random,
1063 &catch_exception_random,
1064 &catch_exception_random,
1065 &catch_exception_random,
1066 &catch_exception_random,
1067 &catch_exception_random,
1068 &catch_exception_random,
1069 &catch_exception_random,
1070 &catch_exception_random,
1071 &catch_exception_random,
1072 &catch_exception_random,
1073 &catch_exception_random,
1074 &catch_exception_random,
1075 &catch_exception_random,
1076 &catch_exception_random,
1077 &catch_exception_random,
1078 &catch_exception_random,
1079 &catch_exception_random,
1080 &catch_exception_random,
1081 &catch_exception_random,
1082 &catch_exception_random,
1083 &catch_exception_random,
1084 &catch_exception_random,
1085 &catch_exception_random,
1086 &catch_exception_random,
1087 &catch_exception_random,
1088 &catch_exception_random,
1089 &catch_exception_random,
1090 &catch_exception_random,
1091 &catch_exception_random,
1092 &catch_exception_random,
1093 &catch_exception_random,
1094 &catch_exception_random,
1095 &catch_exception_random,
1096 &catch_exception_random,
1097 &catch_exception_random,
1098 &catch_exception_random,
1099 &catch_exception_random,
1100 &catch_exception_random,
1101 &catch_exception_random,
1102 &catch_exception_random,
1103 &catch_exception_random,
1104 &catch_exception_random,
1105 &catch_exception_random,
1106 &catch_exception_random,
1107 &catch_exception_random,
1108 &catch_exception_random,
1109 &catch_exception_random,
1110 &catch_exception_random,
1111 &catch_exception_random,
1112 &catch_exception_random,
1113 &catch_exception_random,
1114 &catch_exception_random,
1115 &catch_exception_255}};
1116
1117 #define BCR (*(volatile short *)(0x05FFFFA0)) /* Bus control register */
1118 #define BAS (0x800) /* Byte access select */
1119 #define WCR1 (*(volatile short *)(0x05ffffA2)) /* Wait state control register */
1120
1121 asm ("_BINIT: mov.l L1,r15");
1122 asm ("bra _INIT");
1123 asm ("nop");
1124 asm ("L1: .long _init_stack + 8*1024*4");
1125 void
INIT(void)1126 INIT (void)
1127 {
1128 /* First turn on the ram */
1129 WCR1 = 0; /* Never sample wait */
1130 BCR = BAS; /* use lowbyte/high byte */
1131
1132 init_serial();
1133
1134 #ifdef MONITOR
1135 reset_hook ();
1136 #endif
1137
1138
1139 in_nmi = 0;
1140 dofault = 1;
1141 stepped = 0;
1142
1143 stub_sp = stub_stack + stub_stack_size;
1144 breakpoint ();
1145
1146 while (1)
1147 ;
1148 }
1149
1150
sr()1151 static void sr()
1152 {
1153
1154
1155 /* Calling Reset does the same as pressing the button */
1156 asm (".global _Reset
1157 .global _WarmReset
1158 _Reset:
1159 _WarmReset:
1160 mov.l L_sp,r15
1161 bra _INIT
1162 nop
1163 .align 2
1164 L_sp: .long _init_stack + 8000");
1165
1166 asm("saveRegisters:
1167 mov.l @(L_reg, pc), r0
1168 mov.l @r15+, r1 ! pop R0
1169 mov.l r2, @(0x08, r0) ! save R2
1170 mov.l r1, @r0 ! save R0
1171 mov.l @r15+, r1 ! pop R1
1172 mov.l r3, @(0x0c, r0) ! save R3
1173 mov.l r1, @(0x04, r0) ! save R1
1174 mov.l r4, @(0x10, r0) ! save R4
1175 mov.l r5, @(0x14, r0) ! save R5
1176 mov.l r6, @(0x18, r0) ! save R6
1177 mov.l r7, @(0x1c, r0) ! save R7
1178 mov.l r8, @(0x20, r0) ! save R8
1179 mov.l r9, @(0x24, r0) ! save R9
1180 mov.l r10, @(0x28, r0) ! save R10
1181 mov.l r11, @(0x2c, r0) ! save R11
1182 mov.l r12, @(0x30, r0) ! save R12
1183 mov.l r13, @(0x34, r0) ! save R13
1184 mov.l r14, @(0x38, r0) ! save R14
1185 mov.l @r15+, r4 ! save arg to handleException
1186 add #8, r15 ! hide PC/SR values on stack
1187 mov.l r15, @(0x3c, r0) ! save R15
1188 add #-8, r15 ! save still needs old SP value
1189 add #92, r0 ! readjust register pointer
1190 mov r15, r2
1191 add #4, r2
1192 mov.l @r2, r2 ! R2 has SR
1193 mov.l @r15, r1 ! R1 has PC
1194 mov.l r2, @-r0 ! save SR
1195 sts.l macl, @-r0 ! save MACL
1196 sts.l mach, @-r0 ! save MACH
1197 stc.l vbr, @-r0 ! save VBR
1198 stc.l gbr, @-r0 ! save GBR
1199 sts.l pr, @-r0 ! save PR
1200 mov.l @(L_stubstack, pc), r2
1201 mov.l @(L_hdl_except, pc), r3
1202 mov.l @r2, r15
1203 jsr @r3
1204 mov.l r1, @-r0 ! save PC
1205 mov.l @(L_stubstack, pc), r0
1206 mov.l @(L_reg, pc), r1
1207 bra restoreRegisters
1208 mov.l r15, @r0 ! save __stub_stack
1209
1210 .align 2
1211 L_reg:
1212 .long _registers
1213 L_stubstack:
1214 .long _stub_sp
1215 L_hdl_except:
1216 .long _handle_exception");
1217
1218 }
1219
rr()1220 static void rr()
1221 {
1222 asm("
1223 .align 2
1224 .global _resume
1225 _resume:
1226 mov r4,r1
1227 restoreRegisters:
1228 add #8, r1 ! skip to R2
1229 mov.l @r1+, r2 ! restore R2
1230 mov.l @r1+, r3 ! restore R3
1231 mov.l @r1+, r4 ! restore R4
1232 mov.l @r1+, r5 ! restore R5
1233 mov.l @r1+, r6 ! restore R6
1234 mov.l @r1+, r7 ! restore R7
1235 mov.l @r1+, r8 ! restore R8
1236 mov.l @r1+, r9 ! restore R9
1237 mov.l @r1+, r10 ! restore R10
1238 mov.l @r1+, r11 ! restore R11
1239 mov.l @r1+, r12 ! restore R12
1240 mov.l @r1+, r13 ! restore R13
1241 mov.l @r1+, r14 ! restore R14
1242 mov.l @r1+, r15 ! restore programs stack
1243 mov.l @r1+, r0
1244 add #-8, r15 ! uncover PC/SR on stack
1245 mov.l r0, @r15 ! restore PC onto stack
1246 lds.l @r1+, pr ! restore PR
1247 ldc.l @r1+, gbr ! restore GBR
1248 ldc.l @r1+, vbr ! restore VBR
1249 lds.l @r1+, mach ! restore MACH
1250 lds.l @r1+, macl ! restore MACL
1251 mov.l @r1, r0
1252 add #-88, r1 ! readjust reg pointer to R1
1253 mov.l r0, @(4, r15) ! restore SR onto stack+4
1254 mov.l r2, @-r15
1255 mov.l L_in_nmi, r0
1256 mov #0, r2
1257 mov.b r2, @r0
1258 mov.l @r15+, r2
1259 mov.l @r1+, r0 ! restore R0
1260 rte
1261 mov.l @r1, r1 ! restore R1
1262
1263 ");
1264 }
1265
1266
code_for_catch_exception(int n)1267 static __inline__ void code_for_catch_exception(int n)
1268 {
1269 asm(" .globl _catch_exception_%O0" : : "i" (n) );
1270 asm(" _catch_exception_%O0:" :: "i" (n) );
1271
1272 asm(" add #-4, r15 ! reserve spot on stack ");
1273 asm(" mov.l r1, @-r15 ! push R1 ");
1274
1275 if (n == NMI_VEC)
1276 {
1277 /* Special case for NMI - make sure that they don't nest */
1278 asm(" mov.l r0, @-r15 ! push R0");
1279 asm(" mov.l L_in_nmi, r0");
1280 asm(" tas.b @r0 ! Fend off against addtnl NMIs");
1281 asm(" bt noNMI");
1282 asm(" mov.l @r15+, r0");
1283 asm(" mov.l @r15+, r1");
1284 asm(" add #4, r15");
1285 asm(" rte");
1286 asm(" nop");
1287 asm(".align 2");
1288 asm("L_in_nmi: .long _in_nmi");
1289 asm("noNMI:");
1290 }
1291 else
1292 {
1293
1294 if (n == CPU_BUS_ERROR_VEC)
1295 {
1296 /* Exception 9 (bus errors) are disasbleable - so that you
1297 can probe memory and get zero instead of a fault.
1298 Because the vector table may be in ROM we don't revector
1299 the interrupt like all the other stubs, we check in here
1300 */
1301 asm("mov.l L_dofault,r1");
1302 asm("mov.l @r1,r1");
1303 asm("tst r1,r1");
1304 asm("bf faultaway");
1305 asm("bsr _handle_buserror");
1306 asm(".align 2");
1307 asm("L_dofault: .long _dofault");
1308 asm("faultaway:");
1309 }
1310 asm(" mov #15<<4, r1 ");
1311 asm(" ldc r1, sr ! disable interrupts ");
1312 asm(" mov.l r0, @-r15 ! push R0 ");
1313 }
1314
1315 /* Prepare for saving context, we've already pushed r0 and r1, stick exception number
1316 into the frame */
1317 asm(" mov r15, r0 ");
1318 asm(" add #8, r0 ");
1319 asm(" mov %0,r1" :: "i" (n) );
1320 asm(" extu.b r1,r1 ");
1321 asm(" bra saveRegisters ! save register values ");
1322 asm(" mov.l r1, @r0 ! save exception # ");
1323 }
1324
1325
1326 static void
exceptions(void)1327 exceptions (void)
1328 {
1329 code_for_catch_exception (CPU_BUS_ERROR_VEC);
1330 code_for_catch_exception (DMA_BUS_ERROR_VEC);
1331 code_for_catch_exception (INVALID_INSN_VEC);
1332 code_for_catch_exception (INVALID_SLOT_VEC);
1333 code_for_catch_exception (NMI_VEC);
1334 code_for_catch_exception (TRAP_VEC);
1335 code_for_catch_exception (USER_VEC);
1336 code_for_catch_exception (IO_VEC);
1337 }
1338
1339
1340
1341
1342
1343
1344 /* Support for Serial I/O using on chip uart */
1345
1346 #define SMR0 (*(volatile char *)(0x05FFFEC0)) /* Channel 0 serial mode register */
1347 #define BRR0 (*(volatile char *)(0x05FFFEC1)) /* Channel 0 bit rate register */
1348 #define SCR0 (*(volatile char *)(0x05FFFEC2)) /* Channel 0 serial control register */
1349 #define TDR0 (*(volatile char *)(0x05FFFEC3)) /* Channel 0 transmit data register */
1350 #define SSR0 (*(volatile char *)(0x05FFFEC4)) /* Channel 0 serial status register */
1351 #define RDR0 (*(volatile char *)(0x05FFFEC5)) /* Channel 0 receive data register */
1352
1353 #define SMR1 (*(volatile char *)(0x05FFFEC8)) /* Channel 1 serial mode register */
1354 #define BRR1 (*(volatile char *)(0x05FFFEC9)) /* Channel 1 bit rate register */
1355 #define SCR1 (*(volatile char *)(0x05FFFECA)) /* Channel 1 serial control register */
1356 #define TDR1 (*(volatile char *)(0x05FFFECB)) /* Channel 1 transmit data register */
1357 #define SSR1 (*(volatile char *)(0x05FFFECC)) /* Channel 1 serial status register */
1358 #define RDR1 (*(volatile char *)(0x05FFFECD)) /* Channel 1 receive data register */
1359
1360 /*
1361 * Serial mode register bits
1362 */
1363
1364 #define SYNC_MODE 0x80
1365 #define SEVEN_BIT_DATA 0x40
1366 #define PARITY_ON 0x20
1367 #define ODD_PARITY 0x10
1368 #define STOP_BITS_2 0x08
1369 #define ENABLE_MULTIP 0x04
1370 #define PHI_64 0x03
1371 #define PHI_16 0x02
1372 #define PHI_4 0x01
1373
1374 /*
1375 * Serial control register bits
1376 */
1377 #define SCI_TIE 0x80 /* Transmit interrupt enable */
1378 #define SCI_RIE 0x40 /* Receive interrupt enable */
1379 #define SCI_TE 0x20 /* Transmit enable */
1380 #define SCI_RE 0x10 /* Receive enable */
1381 #define SCI_MPIE 0x08 /* Multiprocessor interrupt enable */
1382 #define SCI_TEIE 0x04 /* Transmit end interrupt enable */
1383 #define SCI_CKE1 0x02 /* Clock enable 1 */
1384 #define SCI_CKE0 0x01 /* Clock enable 0 */
1385
1386 /*
1387 * Serial status register bits
1388 */
1389 #define SCI_TDRE 0x80 /* Transmit data register empty */
1390 #define SCI_RDRF 0x40 /* Receive data register full */
1391 #define SCI_ORER 0x20 /* Overrun error */
1392 #define SCI_FER 0x10 /* Framing error */
1393 #define SCI_PER 0x08 /* Parity error */
1394 #define SCI_TEND 0x04 /* Transmit end */
1395 #define SCI_MPB 0x02 /* Multiprocessor bit */
1396 #define SCI_MPBT 0x01 /* Multiprocessor bit transfer */
1397
1398
1399 /*
1400 * Port B IO Register (PBIOR)
1401 */
1402 #define PBIOR (*(volatile char *)(0x05FFFFC6))
1403 #define PB15IOR 0x8000
1404 #define PB14IOR 0x4000
1405 #define PB13IOR 0x2000
1406 #define PB12IOR 0x1000
1407 #define PB11IOR 0x0800
1408 #define PB10IOR 0x0400
1409 #define PB9IOR 0x0200
1410 #define PB8IOR 0x0100
1411 #define PB7IOR 0x0080
1412 #define PB6IOR 0x0040
1413 #define PB5IOR 0x0020
1414 #define PB4IOR 0x0010
1415 #define PB3IOR 0x0008
1416 #define PB2IOR 0x0004
1417 #define PB1IOR 0x0002
1418 #define PB0IOR 0x0001
1419
1420 /*
1421 * Port B Control Register (PBCR1)
1422 */
1423 #define PBCR1 (*(volatile short *)(0x05FFFFCC))
1424 #define PB15MD1 0x8000
1425 #define PB15MD0 0x4000
1426 #define PB14MD1 0x2000
1427 #define PB14MD0 0x1000
1428 #define PB13MD1 0x0800
1429 #define PB13MD0 0x0400
1430 #define PB12MD1 0x0200
1431 #define PB12MD0 0x0100
1432 #define PB11MD1 0x0080
1433 #define PB11MD0 0x0040
1434 #define PB10MD1 0x0020
1435 #define PB10MD0 0x0010
1436 #define PB9MD1 0x0008
1437 #define PB9MD0 0x0004
1438 #define PB8MD1 0x0002
1439 #define PB8MD0 0x0001
1440
1441 #define PB15MD PB15MD1|PB14MD0
1442 #define PB14MD PB14MD1|PB14MD0
1443 #define PB13MD PB13MD1|PB13MD0
1444 #define PB12MD PB12MD1|PB12MD0
1445 #define PB11MD PB11MD1|PB11MD0
1446 #define PB10MD PB10MD1|PB10MD0
1447 #define PB9MD PB9MD1|PB9MD0
1448 #define PB8MD PB8MD1|PB8MD0
1449
1450 #define PB_TXD1 PB11MD1
1451 #define PB_RXD1 PB10MD1
1452 #define PB_TXD0 PB9MD1
1453 #define PB_RXD0 PB8MD1
1454
1455 /*
1456 * Port B Control Register (PBCR2)
1457 */
1458 #define PBCR2 0x05FFFFCE
1459 #define PB7MD1 0x8000
1460 #define PB7MD0 0x4000
1461 #define PB6MD1 0x2000
1462 #define PB6MD0 0x1000
1463 #define PB5MD1 0x0800
1464 #define PB5MD0 0x0400
1465 #define PB4MD1 0x0200
1466 #define PB4MD0 0x0100
1467 #define PB3MD1 0x0080
1468 #define PB3MD0 0x0040
1469 #define PB2MD1 0x0020
1470 #define PB2MD0 0x0010
1471 #define PB1MD1 0x0008
1472 #define PB1MD0 0x0004
1473 #define PB0MD1 0x0002
1474 #define PB0MD0 0x0001
1475
1476 #define PB7MD PB7MD1|PB7MD0
1477 #define PB6MD PB6MD1|PB6MD0
1478 #define PB5MD PB5MD1|PB5MD0
1479 #define PB4MD PB4MD1|PB4MD0
1480 #define PB3MD PB3MD1|PB3MD0
1481 #define PB2MD PB2MD1|PB2MD0
1482 #define PB1MD PB1MD1|PB1MD0
1483 #define PB0MD PB0MD1|PB0MD0
1484
1485
1486 #ifdef MHZ
1487 #define BPS 32 * 9600 * MHZ / ( BAUD * 10)
1488 #else
1489 #define BPS 32 /* 9600 for 10 Mhz */
1490 #endif
1491
1492 void handleError (char theSSR);
1493
1494 void
nop(void)1495 nop (void)
1496 {
1497
1498 }
1499 void
init_serial(void)1500 init_serial (void)
1501 {
1502 int i;
1503
1504 /* Clear TE and RE in Channel 1's SCR */
1505 SCR1 &= ~(SCI_TE | SCI_RE);
1506
1507 /* Set communication to be async, 8-bit data, no parity, 1 stop bit and use internal clock */
1508
1509 SMR1 = 0;
1510 BRR1 = BPS;
1511
1512 SCR1 &= ~(SCI_CKE1 | SCI_CKE0);
1513
1514 /* let the hardware settle */
1515
1516 for (i = 0; i < 1000; i++)
1517 nop ();
1518
1519 /* Turn on in and out */
1520 SCR1 |= SCI_RE | SCI_TE;
1521
1522 /* Set the PFC to make RXD1 (pin PB8) an input pin and TXD1 (pin PB9) an output pin */
1523 PBCR1 &= ~(PB_TXD1 | PB_RXD1);
1524 PBCR1 |= PB_TXD1 | PB_RXD1;
1525 }
1526
1527
1528 int
getDebugCharReady(void)1529 getDebugCharReady (void)
1530 {
1531 char mySSR;
1532 mySSR = SSR1 & ( SCI_PER | SCI_FER | SCI_ORER );
1533 if ( mySSR )
1534 handleError ( mySSR );
1535 return SSR1 & SCI_RDRF ;
1536 }
1537
1538 char
getDebugChar(void)1539 getDebugChar (void)
1540 {
1541 char ch;
1542 char mySSR;
1543
1544 while ( ! getDebugCharReady())
1545 ;
1546
1547 ch = RDR1;
1548 SSR1 &= ~SCI_RDRF;
1549
1550 mySSR = SSR1 & (SCI_PER | SCI_FER | SCI_ORER);
1551
1552 if (mySSR)
1553 handleError (mySSR);
1554
1555 return ch;
1556 }
1557
1558 int
putDebugCharReady(void)1559 putDebugCharReady (void)
1560 {
1561 return (SSR1 & SCI_TDRE);
1562 }
1563
1564 void
putDebugChar(char ch)1565 putDebugChar (char ch)
1566 {
1567 while (!putDebugCharReady())
1568 ;
1569
1570 /*
1571 * Write data into TDR and clear TDRE
1572 */
1573 TDR1 = ch;
1574 SSR1 &= ~SCI_TDRE;
1575 }
1576
1577 void
handleError(char theSSR)1578 handleError (char theSSR)
1579 {
1580 SSR1 &= ~(SCI_ORER | SCI_PER | SCI_FER);
1581 }
1582
1583 #endif
1584