xref: /linux/drivers/comedi/drivers/plx9080.h (revision 8ffdff6a)
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * plx9080.h
4  *
5  * Copyright (C) 2002,2003 Frank Mori Hess <fmhess@users.sourceforge.net>
6  *
7  ********************************************************************
8  *
9  * Copyright (C) 1999 RG Studio s.c.
10  * Written by Krzysztof Halasa <khc@rgstudio.com.pl>
11  *
12  * Portions (C) SBE Inc., used by permission.
13  */
14 
15 #ifndef __COMEDI_PLX9080_H
16 #define __COMEDI_PLX9080_H
17 
18 #include <linux/compiler.h>
19 #include <linux/types.h>
20 #include <linux/bitops.h>
21 #include <linux/delay.h>
22 #include <linux/errno.h>
23 #include <linux/io.h>
24 
25 /**
26  * struct plx_dma_desc - DMA descriptor format for PLX PCI 9080
27  * @pci_start_addr:	PCI Bus address for transfer (DMAPADR).
28  * @local_start_addr:	Local Bus address for transfer (DMALADR).
29  * @transfer_size:	Transfer size in bytes (max 8 MiB) (DMASIZ).
30  * @next:		Address of next descriptor + flags (DMADPR).
31  *
32  * Describes the format of a scatter-gather DMA descriptor for the PLX
33  * PCI 9080.  All members are raw, little-endian register values that
34  * will be transferred by the DMA engine from local or PCI memory into
35  * corresponding registers for the DMA channel.
36  *
37  * The DMA descriptors must be aligned on a 16-byte boundary.  Bits 3:0
38  * of @next contain flags describing the address space of the next
39  * descriptor (local or PCI), an "end of chain" marker, an "interrupt on
40  * terminal count" bit, and a data transfer direction.
41  */
42 struct plx_dma_desc {
43 	__le32 pci_start_addr;
44 	__le32 local_start_addr;
45 	__le32 transfer_size;
46 	__le32 next;
47 };
48 
49 /*
50  * Register Offsets and Bit Definitions
51  */
52 
53 /* Local Address Space 0 Range Register */
54 #define PLX_REG_LAS0RR		0x0000
55 /* Local Address Space 1 Range Register */
56 #define PLX_REG_LAS1RR		0x00f0
57 
58 #define PLX_LASRR_IO		BIT(0)		/* Map to: 1=I/O, 0=Mem */
59 #define PLX_LASRR_MLOC_ANY32	(BIT(1) * 0)	/* Locate anywhere in 32 bit */
60 #define PLX_LASRR_MLOC_LT1MB	(BIT(1) * 1)	/* Locate in 1st meg */
61 #define PLX_LASRR_MLOC_ANY64	(BIT(1) * 2)	/* Locate anywhere in 64 bit */
62 #define PLX_LASRR_MLOC_MASK	GENMASK(2, 1)	/* Memory location bits */
63 #define PLX_LASRR_PREFETCH	BIT(3)		/* Memory is prefetchable */
64 /* bits that specify range for memory space decode bits */
65 #define PLX_LASRR_MEM_MASK	GENMASK(31, 4)
66 /* bits that specify range for i/o space decode bits */
67 #define PLX_LASRR_IO_MASK	GENMASK(31, 2)
68 
69 /* Local Address Space 0 Local Base Address (Remap) Register */
70 #define PLX_REG_LAS0BA		0x0004
71 /* Local Address Space 1 Local Base Address (Remap) Register */
72 #define PLX_REG_LAS1BA		0x00f4
73 
74 #define PLX_LASBA_EN		BIT(0)		/* Enable slave decode */
75 /* bits that specify local base address for memory space */
76 #define PLX_LASBA_MEM_MASK	GENMASK(31, 4)
77 /* bits that specify local base address for i/o space */
78 #define PLX_LASBA_IO_MASK	GENMASK(31, 2)
79 
80 /* Mode/Arbitration Register */
81 #define PLX_REG_MARBR		0x0008
82 /* DMA Arbitration Register (alias of MARBR). */
83 #define PLX_REG_DMAARB		0x00ac
84 
85 /* Local Bus Latency Timer */
86 #define PLX_MARBR_LT(x)		(BIT(0) * ((x) & 0xff))
87 #define PLX_MARBR_LT_MASK	GENMASK(7, 0)
88 #define PLX_MARBR_TO_LT(r)	((r) & PLX_MARBR_LT_MASK)
89 /* Local Bus Pause Timer */
90 #define PLX_MARBR_PT(x)		(BIT(8) * ((x) & 0xff))
91 #define PLX_MARBR_PT_MASK	GENMASK(15, 8)
92 #define PLX_MARBR_TO_PT(r)	(((r) & PLX_MARBR_PT_MASK) >> 8)
93 /* Local Bus Latency Timer Enable */
94 #define PLX_MARBR_LTEN		BIT(16)
95 /* Local Bus Pause Timer Enable */
96 #define PLX_MARBR_PTEN		BIT(17)
97 /* Local Bus BREQ Enable */
98 #define PLX_MARBR_BREQEN	BIT(18)
99 /* DMA Channel Priority */
100 #define PLX_MARBR_PRIO_ROT	(BIT(19) * 0)	/* Rotational priority */
101 #define PLX_MARBR_PRIO_DMA0	(BIT(19) * 1)	/* DMA channel 0 has priority */
102 #define PLX_MARBR_PRIO_DMA1	(BIT(19) * 2)	/* DMA channel 1 has priority */
103 #define PLX_MARBR_PRIO_MASK	GENMASK(20, 19)
104 /* Local Bus Direct Slave Give Up Bus Mode */
105 #define PLX_MARBR_DSGUBM	BIT(21)
106 /* Direct Slace LLOCKo# Enable */
107 #define PLX_MARBR_DSLLOCKOEN	BIT(22)
108 /* PCI Request Mode */
109 #define PLX_MARBR_PCIREQM	BIT(23)
110 /* PCI Specification v2.1 Mode */
111 #define PLX_MARBR_PCIV21M	BIT(24)
112 /* PCI Read No Write Mode */
113 #define PLX_MARBR_PCIRNWM	BIT(25)
114 /* PCI Read with Write Flush Mode */
115 #define PLX_MARBR_PCIRWFM	BIT(26)
116 /* Gate Local Bus Latency Timer with BREQ */
117 #define PLX_MARBR_GLTBREQ	BIT(27)
118 /* PCI Read No Flush Mode */
119 #define PLX_MARBR_PCIRNFM	BIT(28)
120 /*
121  * Make reads from PCI Configuration register 0 return Subsystem ID and
122  * Subsystem Vendor ID instead of Device ID and Vendor ID
123  */
124 #define PLX_MARBR_SUBSYSIDS	BIT(29)
125 
126 /* Big/Little Endian Descriptor Register */
127 #define PLX_REG_BIGEND		0x000c
128 
129 /* Configuration Register Big Endian Mode */
130 #define PLX_BIGEND_CONFIG	BIT(0)
131 /* Direct Master Big Endian Mode */
132 #define PLX_BIGEND_DM		BIT(1)
133 /* Direct Slave Address Space 0 Big Endian Mode */
134 #define PLX_BIGEND_DSAS0	BIT(2)
135 /* Direct Slave Expansion ROM Big Endian Mode */
136 #define PLX_BIGEND_EROM		BIT(3)
137 /* Big Endian Byte Lane Mode - use most significant byte lanes */
138 #define PLX_BIGEND_BEBLM	BIT(4)
139 /* Direct Slave Address Space 1 Big Endian Mode */
140 #define PLX_BIGEND_DSAS1	BIT(5)
141 /* DMA Channel 1 Big Endian Mode */
142 #define PLX_BIGEND_DMA1		BIT(6)
143 /* DMA Channel 0 Big Endian Mode */
144 #define PLX_BIGEND_DMA0		BIT(7)
145 /* DMA Channel N Big Endian Mode (N <= 1) */
146 #define PLX_BIGEND_DMA(n)	((n) ? PLX_BIGEND_DMA1 : PLX_BIGEND_DMA0)
147 
148 /*
149  * Note: The Expansion ROM  stuff is only relevant to the PC environment.
150  *       This expansion ROM code is executed by the host CPU at boot time.
151  *       For this reason no bit definitions are provided here.
152  */
153 
154 /* Expansion ROM Range Register */
155 #define PLX_REG_EROMRR		0x0010
156 /* Expansion ROM Local Base Address (Remap) Register */
157 #define PLX_REG_EROMBA		0x0014
158 
159 /* Local Address Space 0/Expansion ROM Bus Region Descriptor Register */
160 #define PLX_REG_LBRD0		0x0018
161 /* Local Address Space 1 Bus Region Descriptor Register */
162 #define PLX_REG_LBRD1		0x00f8
163 
164 /* Memory Space Local Bus Width */
165 #define PLX_LBRD_MSWIDTH_8	(BIT(0) * 0)	/* 8 bits wide */
166 #define PLX_LBRD_MSWIDTH_16	(BIT(0) * 1)	/* 16 bits wide */
167 #define PLX_LBRD_MSWIDTH_32	(BIT(0) * 2)	/* 32 bits wide */
168 #define PLX_LBRD_MSWIDTH_32A	(BIT(0) * 3)	/* 32 bits wide */
169 #define PLX_LBRD_MSWIDTH_MASK	GENMASK(1, 0)
170 /* Memory Space Internal Wait States */
171 #define PLX_LBRD_MSIWS(x)	(BIT(2) * ((x) & 0xf))
172 #define PLX_LBRD_MSIWS_MASK	GENMASK(5, 2)
173 #define PLX_LBRD_TO_MSIWS(r)	(((r) & PLS_LBRD_MSIWS_MASK) >> 2)
174 /* Memory Space Ready Input Enable */
175 #define PLX_LBRD_MSREADYIEN	BIT(6)
176 /* Memory Space BTERM# Input Enable */
177 #define PLX_LBRD_MSBTERMIEN	BIT(7)
178 /* Memory Space 0 Prefetch Disable (LBRD0 only) */
179 #define PLX_LBRD0_MSPREDIS	BIT(8)
180 /* Memory Space 1 Burst Enable (LBRD1 only) */
181 #define PLX_LBRD1_MSBURSTEN	BIT(8)
182 /* Expansion ROM Space Prefetch Disable (LBRD0 only) */
183 #define PLX_LBRD0_EROMPREDIS	BIT(9)
184 /* Memory Space 1 Prefetch Disable (LBRD1 only) */
185 #define PLX_LBRD1_MSPREDIS	BIT(9)
186 /* Read Prefetch Count Enable */
187 #define PLX_LBRD_RPFCOUNTEN	BIT(10)
188 /* Prefetch Counter */
189 #define PLX_LBRD_PFCOUNT(x)	(BIT(11) * ((x) & 0xf))
190 #define PLX_LBRD_PFCOUNT_MASK	GENMASK(14, 11)
191 #define PLX_LBRD_TO_PFCOUNT(r)	(((r) & PLX_LBRD_PFCOUNT_MASK) >> 11)
192 /* Expansion ROM Space Local Bus Width (LBRD0 only) */
193 #define PLX_LBRD0_EROMWIDTH_8	(BIT(16) * 0)	/* 8 bits wide */
194 #define PLX_LBRD0_EROMWIDTH_16	(BIT(16) * 1)	/* 16 bits wide */
195 #define PLX_LBRD0_EROMWIDTH_32	(BIT(16) * 2)	/* 32 bits wide */
196 #define PLX_LBRD0_EROMWIDTH_32A	(BIT(16) * 3)	/* 32 bits wide */
197 #define PLX_LBRD0_EROMWIDTH_MASK	GENMASK(17, 16)
198 /* Expansion ROM Space Internal Wait States (LBRD0 only) */
199 #define PLX_LBRD0_EROMIWS(x)	(BIT(18) * ((x) & 0xf))
200 #define PLX_LBRD0_EROMIWS_MASK	GENMASK(21, 18)
201 #define PLX_LBRD0_TO_EROMIWS(r)	(((r) & PLX_LBRD0_EROMIWS_MASK) >> 18)
202 /* Expansion ROM Space Ready Input Enable (LBDR0 only) */
203 #define PLX_LBRD0_EROMREADYIEN	BIT(22)
204 /* Expansion ROM Space BTERM# Input Enable (LBRD0 only) */
205 #define PLX_LBRD0_EROMBTERMIEN	BIT(23)
206 /* Memory Space 0 Burst Enable (LBRD0 only) */
207 #define PLX_LBRD0_MSBURSTEN	BIT(24)
208 /* Extra Long Load From Serial EEPROM  (LBRD0 only) */
209 #define PLX_LBRD0_EELONGLOAD	BIT(25)
210 /* Expansion ROM Space Burst Enable (LBRD0 only) */
211 #define PLX_LBRD0_EROMBURSTEN	BIT(26)
212 /* Direct Slave PCI Write Mode - assert TRDY# when FIFO full (LBRD0 only) */
213 #define PLX_LBRD0_DSWMTRDY	BIT(27)
214 /* PCI Target Retry Delay Clocks / 8 (LBRD0 only) */
215 #define PLX_LBRD0_TRDELAY(x)	(BIT(28) * ((x) & 0xF))
216 #define PLX_LBRD0_TRDELAY_MASK	GENMASK(31, 28)
217 #define PLX_LBRD0_TO_TRDELAY(r)	(((r) & PLX_LBRD0_TRDELAY_MASK) >> 28)
218 
219 /* Local Range Register for Direct Master to PCI */
220 #define PLX_REG_DMRR		0x001c
221 
222 /* Local Bus Base Address Register for Direct Master to PCI Memory */
223 #define PLX_REG_DMLBAM		0x0020
224 
225 /* Local Base Address Register for Direct Master to PCI IO/CFG */
226 #define PLX_REG_DMLBAI		0x0024
227 
228 /* PCI Base Address (Remap) Register for Direct Master to PCI Memory */
229 #define PLX_REG_DMPBAM		0x0028
230 
231 /* Direct Master Memory Access Enable */
232 #define PLX_DMPBAM_MEMACCEN	BIT(0)
233 /* Direct Master I/O Access Enable */
234 #define PLX_DMPBAM_IOACCEN	BIT(1)
235 /* LLOCK# Input Enable */
236 #define PLX_DMPBAM_LLOCKIEN	BIT(2)
237 /* Direct Master Read Prefetch Size Control (bits 12, 3) */
238 #define PLX_DMPBAM_RPSIZE_CONT	((BIT(12) * 0) | (BIT(3) * 0))
239 #define PLX_DMPBAM_RPSIZE_4	((BIT(12) * 0) | (BIT(3) * 1))
240 #define PLX_DMPBAM_RPSIZE_8	((BIT(12) * 1) | (BIT(3) * 0))
241 #define PLX_DMPBAM_RPSIZE_16	((BIT(12) * 1) | (BIT(3) * 1))
242 #define PLX_DMPBAM_RPSIZE_MASK	(BIT(12) | BIT(3))
243 /* Direct Master PCI Read Mode - deassert IRDY when FIFO full */
244 #define PLX_DMPBAM_RMIRDY	BIT(4)
245 /* Programmable Almost Full Level (bits 10, 8:5) */
246 #define PLX_DMPBAM_PAFL(x)	((BIT(10) * !!((x) & 0x10)) | \
247 				 (BIT(5) * ((x) & 0xf)))
248 #define PLX_DMPBAM_TO_PAFL(v)	((((BIT(10) & (v)) >> 1) | \
249 				  (GENMASK(8, 5) & (v))) >> 5)
250 #define PLX_DMPBAM_PAFL_MASK	(BIT(10) | GENMASK(8, 5))
251 /* Write And Invalidate Mode */
252 #define PLX_DMPBAM_WIM		BIT(9)
253 /* Direct Master Prefetch Limit */
254 #define PLX_DBPBAM_PFLIMIT	BIT(11)
255 /* I/O Remap Select */
256 #define PLX_DMPBAM_IOREMAPSEL	BIT(13)
257 /* Direct Master Write Delay */
258 #define PLX_DMPBAM_WDELAY_NONE	(BIT(14) * 0)
259 #define PLX_DMPBAM_WDELAY_4	(BIT(14) * 1)
260 #define PLX_DMPBAM_WDELAY_8	(BIT(14) * 2)
261 #define PLX_DMPBAM_WDELAY_16	(BIT(14) * 3)
262 #define PLX_DMPBAM_WDELAY_MASK	GENMASK(15, 14)
263 /* Remap of Local-to-PCI Space Into PCI Address Space */
264 #define PLX_DMPBAM_REMAP_MASK	GENMASK(31, 16)
265 
266 /* PCI Configuration Address Register for Direct Master to PCI IO/CFG */
267 #define PLX_REG_DMCFGA		0x002c
268 
269 /* Congiguration Type */
270 #define PLX_DMCFGA_TYPE0	(BIT(0) * 0)
271 #define PLX_DMCFGA_TYPE1	(BIT(0) * 1)
272 #define PLX_DMCFGA_TYPE_MASK	GENMASK(1, 0)
273 /* Register Number */
274 #define PLX_DMCFGA_REGNUM(x)	(BIT(2) * ((x) & 0x3f))
275 #define PLX_DMCFGA_REGNUM_MASK	GENMASK(7, 2)
276 #define PLX_DMCFGA_TO_REGNUM(r)	(((r) & PLX_DMCFGA_REGNUM_MASK) >> 2)
277 /* Function Number */
278 #define PLX_DMCFGA_FUNCNUM(x)	(BIT(8) * ((x) & 0x7))
279 #define PLX_DMCFGA_FUNCNUM_MASK	GENMASK(10, 8)
280 #define PLX_DMCFGA_TO_FUNCNUM(r) (((r) & PLX_DMCFGA_FUNCNUM_MASK) >> 8)
281 /* Device Number */
282 #define PLX_DMCFGA_DEVNUM(x)	(BIT(11) * ((x) & 0x1f))
283 #define PLX_DMCFGA_DEVNUM_MASK	GENMASK(15, 11)
284 #define PLX_DMCFGA_TO_DEVNUM(r)	(((r) & PLX_DMCFGA_DEVNUM_MASK) >> 11)
285 /* Bus Number */
286 #define PLX_DMCFGA_BUSNUM(x)	(BIT(16) * ((x) & 0xff))
287 #define PLX_DMCFGA_BUSNUM_MASK	GENMASK(23, 16)
288 #define PLX_DMCFGA_TO_BUSNUM(r)	(((r) & PLX_DMCFGA_BUSNUM_MASK) >> 16)
289 /* Configuration Enable */
290 #define PLX_DMCFGA_CONFIGEN	BIT(31)
291 
292 /*
293  * Mailbox Register N (N <= 7)
294  *
295  * Note that if the I2O feature is enabled (QSR[0] is set), Mailbox Register 0
296  * is replaced by the Inbound Queue Port, and Mailbox Register 1 is replaced
297  * by the Outbound Queue Port.  However, Mailbox Register 0 and 1 are always
298  * accessible at alternative offsets if the I2O feature is enabled.
299  */
300 #define PLX_REG_MBOX(n)		(0x0040 + (n) * 4)
301 #define PLX_REG_MBOX0		PLX_REG_MBOX(0)
302 #define PLX_REG_MBOX1		PLX_REG_MBOX(1)
303 #define PLX_REG_MBOX2		PLX_REG_MBOX(2)
304 #define PLX_REG_MBOX3		PLX_REG_MBOX(3)
305 #define PLX_REG_MBOX4		PLX_REG_MBOX(4)
306 #define PLX_REG_MBOX5		PLX_REG_MBOX(5)
307 #define PLX_REG_MBOX6		PLX_REG_MBOX(6)
308 #define PLX_REG_MBOX7		PLX_REG_MBOX(7)
309 
310 /* Alternative offsets for Mailbox Registers 0 and 1 (in case I2O is enabled) */
311 #define PLX_REG_ALT_MBOX(n)	((n) < 2 ? 0x0078 + (n) * 4 : PLX_REG_MBOX(n))
312 #define PLX_REG_ALT_MBOX0	PLX_REG_ALT_MBOX(0)
313 #define PLX_REG_ALT_MBOX1	PLX_REG_ALT_MBOX(1)
314 
315 /* PCI-to-Local Doorbell Register */
316 #define PLX_REG_P2LDBELL	0x0060
317 
318 /* Local-to-PCI Doorbell Register */
319 #define PLX_REG_L2PDBELL	0x0064
320 
321 /* Interrupt Control/Status Register */
322 #define PLX_REG_INTCSR		0x0068
323 
324 /* Enable Local Bus LSERR# when PCI Bus Target Abort or Master Abort occurs */
325 #define PLX_INTCSR_LSEABORTEN	BIT(0)
326 /* Enable Local Bus LSERR# when PCI parity error occurs */
327 #define PLX_INTCSR_LSEPARITYEN	BIT(1)
328 /* Generate PCI Bus SERR# when set to 1 */
329 #define PLX_INTCSR_GENSERR	BIT(2)
330 /* Mailbox Interrupt Enable (local bus interrupts on PCI write to MBOX0-3) */
331 #define PLX_INTCSR_MBIEN	BIT(3)
332 /* PCI Interrupt Enable */
333 #define PLX_INTCSR_PIEN		BIT(8)
334 /* PCI Doorbell Interrupt Enable */
335 #define PLX_INTCSR_PDBIEN	BIT(9)
336 /* PCI Abort Interrupt Enable */
337 #define PLX_INTCSR_PABORTIEN	BIT(10)
338 /* PCI Local Interrupt Enable */
339 #define PLX_INTCSR_PLIEN	BIT(11)
340 /* Retry Abort Enable (for diagnostic purposes only) */
341 #define PLX_INTCSR_RAEN		BIT(12)
342 /* PCI Doorbell Interrupt Active (read-only) */
343 #define PLX_INTCSR_PDBIA	BIT(13)
344 /* PCI Abort Interrupt Active (read-only) */
345 #define PLX_INTCSR_PABORTIA	BIT(14)
346 /* Local Interrupt (LINTi#) Active (read-only) */
347 #define PLX_INTCSR_PLIA		BIT(15)
348 /* Local Interrupt Output (LINTo#) Enable */
349 #define PLX_INTCSR_LIOEN	BIT(16)
350 /* Local Doorbell Interrupt Enable */
351 #define PLX_INTCSR_LDBIEN	BIT(17)
352 /* DMA Channel 0 Interrupt Enable */
353 #define PLX_INTCSR_DMA0IEN	BIT(18)
354 /* DMA Channel 1 Interrupt Enable */
355 #define PLX_INTCSR_DMA1IEN	BIT(19)
356 /* DMA Channel N Interrupt Enable (N <= 1) */
357 #define PLX_INTCSR_DMAIEN(n)	((n) ? PLX_INTCSR_DMA1IEN : PLX_INTCSR_DMA0IEN)
358 /* Local Doorbell Interrupt Active (read-only) */
359 #define PLX_INTCSR_LDBIA	BIT(20)
360 /* DMA Channel 0 Interrupt Active (read-only) */
361 #define PLX_INTCSR_DMA0IA	BIT(21)
362 /* DMA Channel 1 Interrupt Active (read-only) */
363 #define PLX_INTCSR_DMA1IA	BIT(22)
364 /* DMA Channel N Interrupt Active (N <= 1) (read-only) */
365 #define PLX_INTCSR_DMAIA(n)	((n) ? PLX_INTCSR_DMA1IA : PLX_INTCSR_DMA0IA)
366 /* BIST Interrupt Active (read-only) */
367 #define PLX_INTCSR_BISTIA	BIT(23)
368 /* Direct Master Not Bus Master During Master Or Target Abort (read-only) */
369 #define PLX_INTCSR_ABNOTDM	BIT(24)
370 /* DMA Channel 0 Not Bus Master During Master Or Target Abort (read-only) */
371 #define PLX_INTCSR_ABNOTDMA0	BIT(25)
372 /* DMA Channel 1 Not Bus Master During Master Or Target Abort (read-only) */
373 #define PLX_INTCSR_ABNOTDMA1	BIT(26)
374 /* DMA Channel N Not Bus Master During Master Or Target Abort (read-only) */
375 #define PLX_INTCSR_ABNOTDMA(n)	((n) ? PLX_INTCSR_ABNOTDMA1 \
376 				     : PLX_INTCSR_ABNOTDMA0)
377 /* Target Abort Not Generated After 256 Master Retries (read-only) */
378 #define PLX_INTCSR_ABNOTRETRY	BIT(27)
379 /* PCI Wrote Mailbox 0 (enabled if bit 3 set) (read-only) */
380 #define PLX_INTCSR_MB0IA	BIT(28)
381 /* PCI Wrote Mailbox 1 (enabled if bit 3 set) (read-only) */
382 #define PLX_INTCSR_MB1IA	BIT(29)
383 /* PCI Wrote Mailbox 2 (enabled if bit 3 set) (read-only) */
384 #define PLX_INTCSR_MB2IA	BIT(30)
385 /* PCI Wrote Mailbox 3 (enabled if bit 3 set) (read-only) */
386 #define PLX_INTCSR_MB3IA	BIT(31)
387 /* PCI Wrote Mailbox N (N <= 3) (enabled if bit 3 set) (read-only) */
388 #define PLX_INTCSR_MBIA(n)	BIT(28 + (n))
389 
390 /*
391  * Serial EEPROM Control, PCI Command Codes, User I/O Control,
392  * Init Control Register
393  */
394 #define PLX_REG_CNTRL		0x006c
395 
396 /* PCI Read Command Code For DMA */
397 #define PLX_CNTRL_CCRDMA(x)	(BIT(0) * ((x) & 0xf))
398 #define PLX_CNTRL_CCRDMA_MASK	GENMASK(3, 0)
399 #define PLX_CNTRL_TO_CCRDMA(r)	((r) & PLX_CNTRL_CCRDMA_MASK)
400 #define PLX_CNTRL_CCRDMA_NORMAL	PLX_CNTRL_CCRDMA(14)	/* value after reset */
401 /* PCI Write Command Code For DMA 0 */
402 #define PLX_CNTRL_CCWDMA(x)	(BIT(4) * ((x) & 0xf))
403 #define PLX_CNTRL_CCWDMA_MASK	GENMASK(7, 4)
404 #define PLX_CNTRL_TO_CCWDMA(r)	(((r) & PLX_CNTRL_CCWDMA_MASK) >> 4)
405 #define PLX_CNTRL_CCWDMA_NORMAL	PLX_CNTRL_CCWDMA(7)	/* value after reset */
406 /* PCI Memory Read Command Code For Direct Master */
407 #define PLX_CNTRL_CCRDM(x)	(BIT(8) * ((x) & 0xf))
408 #define PLX_CNTRL_CCRDM_MASK	GENMASK(11, 8)
409 #define PLX_CNTRL_TO_CCRDM(r)	(((r) & PLX_CNTRL_CCRDM_MASK) >> 8)
410 #define PLX_CNTRL_CCRDM_NORMAL	PLX_CNTRL_CCRDM(6)	/* value after reset */
411 /* PCI Memory Write Command Code For Direct Master */
412 #define PLX_CNTRL_CCWDM(x)	(BIT(12) * ((x) & 0xf))
413 #define PLX_CNTRL_CCWDM_MASK	GENMASK(15, 12)
414 #define PLX_CNTRL_TO_CCWDM(r)	(((r) & PLX_CNTRL_CCWDM_MASK) >> 12)
415 #define PLX_CNTRL_CCWDM_NORMAL	PLX_CNTRL_CCWDM(7)	/* value after reset */
416 /* General Purpose Output (USERO) */
417 #define PLX_CNTRL_USERO		BIT(16)
418 /* General Purpose Input (USERI) (read-only) */
419 #define PLX_CNTRL_USERI		BIT(17)
420 /* Serial EEPROM Clock Output (EESK) */
421 #define PLX_CNTRL_EESK		BIT(24)
422 /* Serial EEPROM Chip Select Output (EECS) */
423 #define PLX_CNTRL_EECS		BIT(25)
424 /* Serial EEPROM Data Write Bit (EEDI (sic)) */
425 #define PLX_CNTRL_EEWB		BIT(26)
426 /* Serial EEPROM Data Read Bit (EEDO (sic)) (read-only) */
427 #define PLX_CNTRL_EERB		BIT(27)
428 /* Serial EEPROM Present (read-only) */
429 #define PLX_CNTRL_EEPRESENT	BIT(28)
430 /* Reload Configuration Registers from EEPROM */
431 #define PLX_CNTRL_EERELOAD	BIT(29)
432 /* PCI Adapter Software Reset (asserts LRESETo#) */
433 #define PLX_CNTRL_RESET		BIT(30)
434 /* Local Init Status (read-only) */
435 #define PLX_CNTRL_INITDONE	BIT(31)
436 /*
437  * Combined command code stuff for convenience.
438  */
439 #define PLX_CNTRL_CC_MASK	\
440 	(PLX_CNTRL_CCRDMA_MASK | PLX_CNTRL_CCWDMA_MASK | \
441 	 PLX_CNTRL_CCRDM_MASK | PLX_CNTRL_CCWDM_MASK)
442 #define PLX_CNTRL_CC_NORMAL	\
443 	(PLX_CNTRL_CCRDMA_NORMAL | PLX_CNTRL_CCWDMA_NORMAL | \
444 	 PLX_CNTRL_CCRDM_NORMAL | PLX_CNTRL_CCWDM_NORMAL) /* val after reset */
445 
446 /* PCI Permanent Configuration ID Register (hard-coded PLX vendor and device) */
447 #define PLX_REG_PCIHIDR		0x0070
448 
449 /* Hard-coded ID for PLX PCI 9080 */
450 #define PLX_PCIHIDR_9080	0x908010b5
451 
452 /* PCI Permanent Revision ID Register (hard-coded silicon revision) (8-bit). */
453 #define PLX_REG_PCIHREV		0x0074
454 
455 /* DMA Channel N Mode Register (N <= 1) */
456 #define PLX_REG_DMAMODE(n)	((n) ? PLX_REG_DMAMODE1 : PLX_REG_DMAMODE0)
457 #define PLX_REG_DMAMODE0	0x0080
458 #define PLX_REG_DMAMODE1	0x0094
459 
460 /* Local Bus Width */
461 #define PLX_DMAMODE_WIDTH_8	(BIT(0) * 0)	/* 8 bits wide */
462 #define PLX_DMAMODE_WIDTH_16	(BIT(0) * 1)	/* 16 bits wide */
463 #define PLX_DMAMODE_WIDTH_32	(BIT(0) * 2)	/* 32 bits wide */
464 #define PLX_DMAMODE_WIDTH_32A	(BIT(0) * 3)	/* 32 bits wide */
465 #define PLX_DMAMODE_WIDTH_MASK	GENMASK(1, 0)
466 /* Internal Wait States */
467 #define PLX_DMAMODE_IWS(x)	(BIT(2) * ((x) & 0xf))
468 #define PLX_DMAMODE_IWS_MASK	GENMASK(5, 2)
469 #define PLX_DMAMODE_TO_IWS(r)	(((r) & PLX_DMAMODE_IWS_MASK) >> 2)
470 /* Ready Input Enable */
471 #define PLX_DMAMODE_READYIEN	BIT(6)
472 /* BTERM# Input Enable */
473 #define PLX_DMAMODE_BTERMIEN	BIT(7)
474 /* Local Burst Enable */
475 #define PLX_DMAMODE_BURSTEN	BIT(8)
476 /* Chaining Enable */
477 #define PLX_DMAMODE_CHAINEN	BIT(9)
478 /* Done Interrupt Enable */
479 #define PLX_DMAMODE_DONEIEN	BIT(10)
480 /* Hold Local Address Constant */
481 #define PLX_DMAMODE_LACONST	BIT(11)
482 /* Demand Mode */
483 #define PLX_DMAMODE_DEMAND	BIT(12)
484 /* Write And Invalidate Mode */
485 #define PLX_DMAMODE_WINVALIDATE	BIT(13)
486 /* DMA EOT Enable - enables EOT0# or EOT1# input pin */
487 #define PLX_DMAMODE_EOTEN	BIT(14)
488 /* DMA Stop Data Transfer Mode - 0:BLAST; 1:EOT asserted or DREQ deasserted */
489 #define PLX_DMAMODE_STOP	BIT(15)
490 /* DMA Clear Count Mode - count in descriptor cleared on completion */
491 #define PLX_DMAMODE_CLRCOUNT	BIT(16)
492 /* DMA Channel Interrupt Select - 0:local bus interrupt; 1:PCI interrupt */
493 #define PLX_DMAMODE_INTRPCI	BIT(17)
494 
495 /* DMA Channel N PCI Address Register (N <= 1) */
496 #define PLX_REG_DMAPADR(n)	((n) ? PLX_REG_DMAPADR1 : PLX_REG_DMAPADR0)
497 #define PLX_REG_DMAPADR0	0x0084
498 #define PLX_REG_DMAPADR1	0x0098
499 
500 /* DMA Channel N Local Address Register (N <= 1) */
501 #define PLX_REG_DMALADR(n)	((n) ? PLX_REG_DMALADR1 : PLX_REG_DMALADR0)
502 #define PLX_REG_DMALADR0	0x0088
503 #define PLX_REG_DMALADR1	0x009c
504 
505 /* DMA Channel N Transfer Size (Bytes) Register (N <= 1) (first 23 bits) */
506 #define PLX_REG_DMASIZ(n)	((n) ? PLX_REG_DMASIZ1 : PLX_REG_DMASIZ0)
507 #define PLX_REG_DMASIZ0		0x008c
508 #define PLX_REG_DMASIZ1		0x00a0
509 
510 /* DMA Channel N Descriptor Pointer Register (N <= 1) */
511 #define PLX_REG_DMADPR(n)	((n) ? PLX_REG_DMADPR1 : PLX_REG_DMADPR0)
512 #define PLX_REG_DMADPR0		0x0090
513 #define PLX_REG_DMADPR1		0x00a4
514 
515 /* Descriptor Located In PCI Address Space (not local address space) */
516 #define PLX_DMADPR_DESCPCI	BIT(0)
517 /* End Of Chain */
518 #define PLX_DMADPR_CHAINEND	BIT(1)
519 /* Interrupt After Terminal Count */
520 #define PLX_DMADPR_TCINTR	BIT(2)
521 /* Direction Of Transfer Local Bus To PCI (not PCI to local) */
522 #define PLX_DMADPR_XFERL2P	BIT(3)
523 /* Next Descriptor Address Bits 31:4 (16 byte boundary) */
524 #define PLX_DMADPR_NEXT_MASK	GENMASK(31, 4)
525 
526 /* DMA Channel N Command/Status Register (N <= 1) (8-bit) */
527 #define PLX_REG_DMACSR(n)	((n) ? PLX_REG_DMACSR1 : PLX_REG_DMACSR0)
528 #define PLX_REG_DMACSR0		0x00a8
529 #define PLX_REG_DMACSR1		0x00a9
530 
531 /* Channel Enable */
532 #define PLX_DMACSR_ENABLE	BIT(0)
533 /* Channel Start - write 1 to start transfer (write-only) */
534 #define PLX_DMACSR_START	BIT(1)
535 /* Channel Abort - write 1 to abort transfer (write-only) */
536 #define PLX_DMACSR_ABORT	BIT(2)
537 /* Clear Interrupt - write 1 to clear DMA Channel Interrupt (write-only) */
538 #define PLX_DMACSR_CLEARINTR	BIT(3)
539 /* Channel Done - transfer complete/inactive (read-only) */
540 #define PLX_DMACSR_DONE		BIT(4)
541 
542 /* DMA Threshold Register */
543 #define PLX_REG_DMATHR		0x00b0
544 
545 /*
546  * DMA Threshold constraints:
547  * (C0PLAF + 1) + (C0PLAE + 1) <= 32
548  * (C0LPAF + 1) + (C0LPAE + 1) <= 32
549  * (C1PLAF + 1) + (C1PLAE + 1) <= 16
550  * (C1LPAF + 1) + (C1LPAE + 1) <= 16
551  */
552 
553 /* DMA Channel 0 PCI-to-Local Almost Full (divided by 2, minus 1) */
554 #define PLX_DMATHR_C0PLAF(x)	(BIT(0) * ((x) & 0xf))
555 #define PLX_DMATHR_C0PLAF_MASK	GENMASK(3, 0)
556 #define PLX_DMATHR_TO_C0PLAF(r)	((r) & PLX_DMATHR_C0PLAF_MASK)
557 /* DMA Channel 0 Local-to-PCI Almost Empty (divided by 2, minus 1) */
558 #define PLX_DMATHR_C0LPAE(x)	(BIT(4) * ((x) & 0xf))
559 #define PLX_DMATHR_C0LPAE_MASK	GENMASK(7, 4)
560 #define PLX_DMATHR_TO_C0LPAE(r)	(((r) & PLX_DMATHR_C0LPAE_MASK) >> 4)
561 /* DMA Channel 0 Local-to-PCI Almost Full (divided by 2, minus 1) */
562 #define PLX_DMATHR_C0LPAF(x)	(BIT(8) * ((x) & 0xf))
563 #define PLX_DMATHR_C0LPAF_MASK	GENMASK(11, 8)
564 #define PLX_DMATHR_TO_C0LPAF(r)	(((r) & PLX_DMATHR_C0LPAF_MASK) >> 8)
565 /* DMA Channel 0 PCI-to-Local Almost Empty (divided by 2, minus 1) */
566 #define PLX_DMATHR_C0PLAE(x)	(BIT(12) * ((x) & 0xf))
567 #define PLX_DMATHR_C0PLAE_MASK	GENMASK(15, 12)
568 #define PLX_DMATHR_TO_C0PLAE(r)	(((r) & PLX_DMATHR_C0PLAE_MASK) >> 12)
569 /* DMA Channel 1 PCI-to-Local Almost Full (divided by 2, minus 1) */
570 #define PLX_DMATHR_C1PLAF(x)	(BIT(16) * ((x) & 0xf))
571 #define PLX_DMATHR_C1PLAF_MASK	GENMASK(19, 16)
572 #define PLX_DMATHR_TO_C1PLAF(r)	(((r) & PLX_DMATHR_C1PLAF_MASK) >> 16)
573 /* DMA Channel 1 Local-to-PCI Almost Empty (divided by 2, minus 1) */
574 #define PLX_DMATHR_C1LPAE(x)	(BIT(20) * ((x) & 0xf))
575 #define PLX_DMATHR_C1LPAE_MASK	GENMASK(23, 20)
576 #define PLX_DMATHR_TO_C1LPAE(r)	(((r) & PLX_DMATHR_C1LPAE_MASK) >> 20)
577 /* DMA Channel 1 Local-to-PCI Almost Full (divided by 2, minus 1) */
578 #define PLX_DMATHR_C1LPAF(x)	(BIT(24) * ((x) & 0xf))
579 #define PLX_DMATHR_C1LPAF_MASK	GENMASK(27, 24)
580 #define PLX_DMATHR_TO_C1LPAF(r)	(((r) & PLX_DMATHR_C1LPAF_MASK) >> 24)
581 /* DMA Channel 1 PCI-to-Local Almost Empty (divided by 2, minus 1) */
582 #define PLX_DMATHR_C1PLAE(x)	(BIT(28) * ((x) & 0xf))
583 #define PLX_DMATHR_C1PLAE_MASK	GENMASK(31, 28)
584 #define PLX_DMATHR_TO_C1PLAE(r)	(((r) & PLX_DMATHR_C1PLAE_MASK) >> 28)
585 
586 /*
587  * Messaging Queue Registers OPLFIS, OPLFIM, IQP, OQP, MQCR, QBAR, IFHPR,
588  * IFTPR, IPHPR, IPTPR, OFHPR, OFTPR, OPHPR, OPTPR, and QSR have been omitted.
589  * They are used by the I2O feature.  (IQP and OQP occupy the usual offsets of
590  * the MBOX0 and MBOX1 registers if the I2O feature is enabled, but MBOX0 and
591  * MBOX1 are accessible via alternative offsets.
592  */
593 
594 /* Queue Status/Control Register */
595 #define PLX_REG_QSR		0x00e8
596 
597 /* Value of QSR after reset - disables I2O feature completely. */
598 #define PLX_QSR_VALUE_AFTER_RESET	0x00000050
599 
600 /*
601  * Accesses near the end of memory can cause the PLX chip
602  * to pre-fetch data off of end-of-ram.  Limit the size of
603  * memory so host-side accesses cannot occur.
604  */
605 
606 #define PLX_PREFETCH   32
607 
608 /**
609  * plx9080_abort_dma - Abort a PLX PCI 9080 DMA transfer
610  * @iobase:	Remapped base address of configuration registers.
611  * @channel:	DMA channel number (0 or 1).
612  *
613  * Aborts the DMA transfer on the channel, which must have been enabled
614  * and started beforehand.
615  *
616  * Return:
617  *	%0 on success.
618  *	-%ETIMEDOUT if timed out waiting for abort to complete.
619  */
plx9080_abort_dma(void __iomem * iobase,unsigned int channel)620 static inline int plx9080_abort_dma(void __iomem *iobase, unsigned int channel)
621 {
622 	void __iomem *dma_cs_addr;
623 	u8 dma_status;
624 	const int timeout = 10000;
625 	unsigned int i;
626 
627 	dma_cs_addr = iobase + PLX_REG_DMACSR(channel);
628 
629 	/* abort dma transfer if necessary */
630 	dma_status = readb(dma_cs_addr);
631 	if ((dma_status & PLX_DMACSR_ENABLE) == 0)
632 		return 0;
633 
634 	/* wait to make sure done bit is zero */
635 	for (i = 0; (dma_status & PLX_DMACSR_DONE) && i < timeout; i++) {
636 		udelay(1);
637 		dma_status = readb(dma_cs_addr);
638 	}
639 	if (i == timeout)
640 		return -ETIMEDOUT;
641 
642 	/* disable and abort channel */
643 	writeb(PLX_DMACSR_ABORT, dma_cs_addr);
644 	/* wait for dma done bit */
645 	dma_status = readb(dma_cs_addr);
646 	for (i = 0; (dma_status & PLX_DMACSR_DONE) == 0 && i < timeout; i++) {
647 		udelay(1);
648 		dma_status = readb(dma_cs_addr);
649 	}
650 	if (i == timeout)
651 		return -ETIMEDOUT;
652 
653 	return 0;
654 }
655 
656 #endif /* __COMEDI_PLX9080_H */
657