1 /* $NetBSD: if_sip.c,v 1.190 2023/06/02 08:51:47 andvar Exp $ */
2
3 /*-
4 * Copyright (c) 2001, 2002 The NetBSD Foundation, Inc.
5 * All rights reserved.
6 *
7 * This code is derived from software contributed to The NetBSD Foundation
8 * by Jason R. Thorpe.
9 *
10 * Redistribution and use in source and binary forms, with or without
11 * modification, are permitted provided that the following conditions
12 * are met:
13 * 1. Redistributions of source code must retain the above copyright
14 * notice, this list of conditions and the following disclaimer.
15 * 2. Redistributions in binary form must reproduce the above copyright
16 * notice, this list of conditions and the following disclaimer in the
17 * documentation and/or other materials provided with the distribution.
18 *
19 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
20 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
21 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
22 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
23 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
24 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
25 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
26 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
27 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
28 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
29 * POSSIBILITY OF SUCH DAMAGE.
30 */
31
32 /*-
33 * Copyright (c) 1999 Network Computer, Inc.
34 * All rights reserved.
35 *
36 * Redistribution and use in source and binary forms, with or without
37 * modification, are permitted provided that the following conditions
38 * are met:
39 * 1. Redistributions of source code must retain the above copyright
40 * notice, this list of conditions and the following disclaimer.
41 * 2. Redistributions in binary form must reproduce the above copyright
42 * notice, this list of conditions and the following disclaimer in the
43 * documentation and/or other materials provided with the distribution.
44 * 3. Neither the name of Network Computer, Inc. nor the names of its
45 * contributors may be used to endorse or promote products derived
46 * from this software without specific prior written permission.
47 *
48 * THIS SOFTWARE IS PROVIDED BY NETWORK COMPUTER, INC. AND CONTRIBUTORS
49 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
50 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
51 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
52 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
53 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
54 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
55 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
56 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
57 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
58 * POSSIBILITY OF SUCH DAMAGE.
59 */
60
61 /*
62 * Device driver for the Silicon Integrated Systems SiS 900,
63 * SiS 7016 10/100, National Semiconductor DP83815 10/100, and
64 * National Semiconductor DP83820 10/100/1000 PCI Ethernet
65 * controllers.
66 *
67 * Originally written to support the SiS 900 by Jason R. Thorpe for
68 * Network Computer, Inc.
69 *
70 * TODO:
71 *
72 * - Reduce the Rx interrupt load.
73 */
74
75 #include <sys/cdefs.h>
76 __KERNEL_RCSID(0, "$NetBSD: if_sip.c,v 1.190 2023/06/02 08:51:47 andvar Exp $");
77
78 #include <sys/param.h>
79 #include <sys/systm.h>
80 #include <sys/callout.h>
81 #include <sys/mbuf.h>
82 #include <sys/kernel.h>
83 #include <sys/socket.h>
84 #include <sys/ioctl.h>
85 #include <sys/errno.h>
86 #include <sys/device.h>
87 #include <sys/queue.h>
88 #include <sys/rndsource.h>
89
90 #include <net/if.h>
91 #include <net/if_dl.h>
92 #include <net/if_media.h>
93 #include <net/if_ether.h>
94 #include <net/bpf.h>
95
96 #include <sys/bus.h>
97 #include <sys/intr.h>
98 #include <machine/endian.h>
99
100 #include <dev/mii/mii.h>
101 #include <dev/mii/miivar.h>
102 #include <dev/mii/mii_bitbang.h>
103
104 #include <dev/pci/pcireg.h>
105 #include <dev/pci/pcivar.h>
106 #include <dev/pci/pcidevs.h>
107
108 #include <dev/pci/if_sipreg.h>
109
110 /*
111 * Transmit descriptor list size. This is arbitrary, but allocate
112 * enough descriptors for 128 pending transmissions, and 8 segments
113 * per packet (64 for DP83820 for jumbo frames).
114 *
115 * This MUST work out to a power of 2.
116 */
117 #define GSIP_NTXSEGS_ALLOC 16
118 #define SIP_NTXSEGS_ALLOC 8
119
120 #define SIP_TXQUEUELEN 256
121 #define MAX_SIP_NTXDESC \
122 (SIP_TXQUEUELEN * MAX(SIP_NTXSEGS_ALLOC, GSIP_NTXSEGS_ALLOC))
123
124 /*
125 * Receive descriptor list size. We have one Rx buffer per incoming
126 * packet, so this logic is a little simpler.
127 *
128 * Actually, on the DP83820, we allow the packet to consume more than
129 * one buffer, in order to support jumbo Ethernet frames. In that
130 * case, a packet may consume up to 5 buffers (assuming a 2048 byte
131 * mbuf cluster). 256 receive buffers is only 51 maximum size packets,
132 * so we'd better be quick about handling receive interrupts.
133 */
134 #define GSIP_NRXDESC 256
135 #define SIP_NRXDESC 128
136
137 #define MAX_SIP_NRXDESC MAX(GSIP_NRXDESC, SIP_NRXDESC)
138
139 /*
140 * Set this to 1 to force-disable using the 64-bit data path
141 * on DP83820.
142 */
143 static int gsip_disable_data64 = 0;
144
145 /*
146 * Control structures are DMA'd to the SiS900 chip. We allocate them in
147 * a single clump that maps to a single DMA segment to make several things
148 * easier.
149 */
150 struct sip_control_data {
151 /*
152 * The transmit descriptors.
153 */
154 struct sip_desc scd_txdescs[MAX_SIP_NTXDESC];
155
156 /*
157 * The receive descriptors.
158 */
159 struct sip_desc scd_rxdescs[MAX_SIP_NRXDESC];
160 };
161
162 #define SIP_CDOFF(x) offsetof(struct sip_control_data, x)
163 #define SIP_CDTXOFF(x) SIP_CDOFF(scd_txdescs[(x)])
164 #define SIP_CDRXOFF(x) SIP_CDOFF(scd_rxdescs[(x)])
165
166 /*
167 * Software state for transmit jobs.
168 */
169 struct sip_txsoft {
170 struct mbuf *txs_mbuf; /* head of our mbuf chain */
171 bus_dmamap_t txs_dmamap; /* our DMA map */
172 int txs_firstdesc; /* first descriptor in packet */
173 int txs_lastdesc; /* last descriptor in packet */
174 SIMPLEQ_ENTRY(sip_txsoft) txs_q;
175 };
176
177 SIMPLEQ_HEAD(sip_txsq, sip_txsoft);
178
179 /*
180 * Software state for receive jobs.
181 */
182 struct sip_rxsoft {
183 struct mbuf *rxs_mbuf; /* head of our mbuf chain */
184 bus_dmamap_t rxs_dmamap; /* our DMA map */
185 };
186
187 enum sip_attach_stage {
188 SIP_ATTACH_FIN = 0
189 , SIP_ATTACH_CREATE_RXMAP
190 , SIP_ATTACH_CREATE_TXMAP
191 , SIP_ATTACH_LOAD_MAP
192 , SIP_ATTACH_CREATE_MAP
193 , SIP_ATTACH_MAP_MEM
194 , SIP_ATTACH_ALLOC_MEM
195 , SIP_ATTACH_INTR
196 , SIP_ATTACH_MAP
197 };
198
199 /*
200 * Software state per device.
201 */
202 struct sip_softc {
203 device_t sc_dev; /* generic device information */
204 device_suspensor_t sc_suspensor;
205 pmf_qual_t sc_qual;
206
207 bus_space_tag_t sc_st; /* bus space tag */
208 bus_space_handle_t sc_sh; /* bus space handle */
209 bus_size_t sc_sz; /* bus space size */
210 bus_dma_tag_t sc_dmat; /* bus DMA tag */
211 pci_chipset_tag_t sc_pc;
212 bus_dma_segment_t sc_seg;
213 struct ethercom sc_ethercom; /* ethernet common data */
214
215 const struct sip_product *sc_model; /* which model are we? */
216 bool sc_gigabit; /* 1: 83820, 0: other */
217 bool sc_dma64; /* using 64-bit DMA addresses */
218 int sc_rev; /* chip revision */
219
220 unsigned int sc_bufptr_idx;
221 unsigned int sc_cmdsts_idx;
222 unsigned int sc_extsts_idx; /* DP83820 only */
223
224 void *sc_ih; /* interrupt cookie */
225
226 struct mii_data sc_mii; /* MII/media information */
227
228 callout_t sc_tick_ch; /* tick callout */
229
230 bus_dmamap_t sc_cddmamap; /* control data DMA map */
231 #define sc_cddma sc_cddmamap->dm_segs[0].ds_addr
232
233 /*
234 * Software state for transmit and receive descriptors.
235 */
236 struct sip_txsoft sc_txsoft[SIP_TXQUEUELEN];
237 struct sip_rxsoft sc_rxsoft[MAX_SIP_NRXDESC];
238
239 /*
240 * Control data structures.
241 */
242 struct sip_control_data *sc_control_data;
243 #define sc_txdescs sc_control_data->scd_txdescs
244 #define sc_rxdescs sc_control_data->scd_rxdescs
245
246 #ifdef SIP_EVENT_COUNTERS
247 /*
248 * Event counters.
249 */
250 struct evcnt sc_ev_txdstall; /* Tx stalled due to no txd */
251 struct evcnt sc_ev_txforceintr; /* Tx interrupts forced */
252 struct evcnt sc_ev_txdintr; /* Tx descriptor interrupts */
253 struct evcnt sc_ev_txiintr; /* Tx idle interrupts */
254 struct evcnt sc_ev_rxintr; /* Rx interrupts */
255 struct evcnt sc_ev_hiberr; /* HIBERR interrupts */
256 struct evcnt sc_ev_rxpause; /* PAUSE received */
257 /* DP83820 only */
258 struct evcnt sc_ev_txpause; /* PAUSE transmitted */
259 struct evcnt sc_ev_rxipsum; /* IP checksums checked in-bound */
260 struct evcnt sc_ev_rxtcpsum; /* TCP checksums checked in-bound */
261 struct evcnt sc_ev_rxudpsum; /* UDP checksums checked in-bound */
262 struct evcnt sc_ev_txipsum; /* IP checksums comp. out-bound */
263 struct evcnt sc_ev_txtcpsum; /* TCP checksums comp. out-bound */
264 struct evcnt sc_ev_txudpsum; /* UDP checksums comp. out-bound */
265 #endif /* SIP_EVENT_COUNTERS */
266
267 uint32_t sc_txcfg; /* prototype TXCFG register */
268 uint32_t sc_rxcfg; /* prototype RXCFG register */
269 uint32_t sc_imr; /* prototype IMR register */
270 uint32_t sc_rfcr; /* prototype RFCR register */
271
272 uint32_t sc_cfg; /* prototype CFG register */
273
274 uint32_t sc_gpior; /* prototype GPIOR register */
275
276 uint32_t sc_tx_fill_thresh; /* transmit fill threshold */
277 uint32_t sc_tx_drain_thresh; /* transmit drain threshold */
278
279 uint32_t sc_rx_drain_thresh; /* receive drain threshold */
280
281 int sc_flowflags; /* 802.3x flow control flags */
282 int sc_rx_flow_thresh; /* Rx FIFO threshold for flow control */
283 int sc_paused; /* paused indication */
284
285 int sc_txfree; /* number of free Tx descriptors */
286 int sc_txnext; /* next ready Tx descriptor */
287 int sc_txwin; /* Tx descriptors since last intr */
288
289 struct sip_txsq sc_txfreeq; /* free Tx descsofts */
290 struct sip_txsq sc_txdirtyq; /* dirty Tx descsofts */
291
292 /* values of interface state at last init */
293 struct {
294 /* if_capenable */
295 uint64_t if_capenable;
296 /* ec_capenable */
297 int ec_capenable;
298 /* VLAN_ATTACHED */
299 int is_vlan;
300 } sc_prev;
301
302 u_short sc_if_flags;
303
304 int sc_rxptr; /* next ready Rx descriptor/descsoft */
305 int sc_rxdiscard;
306 int sc_rxlen;
307 struct mbuf *sc_rxhead;
308 struct mbuf *sc_rxtail;
309 struct mbuf **sc_rxtailp;
310
311 int sc_ntxdesc;
312 int sc_ntxdesc_mask;
313
314 int sc_nrxdesc_mask;
315
316 const struct sip_parm {
317 const struct sip_regs {
318 int r_rxcfg;
319 int r_txcfg;
320 } p_regs;
321
322 const struct sip_bits {
323 uint32_t b_txcfg_mxdma_8;
324 uint32_t b_txcfg_mxdma_16;
325 uint32_t b_txcfg_mxdma_32;
326 uint32_t b_txcfg_mxdma_64;
327 uint32_t b_txcfg_mxdma_128;
328 uint32_t b_txcfg_mxdma_256;
329 uint32_t b_txcfg_mxdma_512;
330 uint32_t b_txcfg_flth_mask;
331 uint32_t b_txcfg_drth_mask;
332
333 uint32_t b_rxcfg_mxdma_8;
334 uint32_t b_rxcfg_mxdma_16;
335 uint32_t b_rxcfg_mxdma_32;
336 uint32_t b_rxcfg_mxdma_64;
337 uint32_t b_rxcfg_mxdma_128;
338 uint32_t b_rxcfg_mxdma_256;
339 uint32_t b_rxcfg_mxdma_512;
340
341 uint32_t b_isr_txrcmp;
342 uint32_t b_isr_rxrcmp;
343 uint32_t b_isr_dperr;
344 uint32_t b_isr_sserr;
345 uint32_t b_isr_rmabt;
346 uint32_t b_isr_rtabt;
347
348 uint32_t b_cmdsts_size_mask;
349 } p_bits;
350 int p_filtmem;
351 int p_rxbuf_len;
352 bus_size_t p_tx_dmamap_size;
353 int p_ntxsegs;
354 int p_ntxsegs_alloc;
355 int p_nrxdesc;
356 } *sc_parm;
357
358 void (*sc_rxintr)(struct sip_softc *);
359
360 krndsource_t rnd_source; /* random source */
361 };
362
363 #define sc_bits sc_parm->p_bits
364 #define sc_regs sc_parm->p_regs
365
366 static const struct sip_parm sip_parm = {
367 .p_filtmem = OTHER_RFCR_NS_RFADDR_FILTMEM
368 , .p_rxbuf_len = MCLBYTES - 1 /* field width */
369 , .p_tx_dmamap_size = MCLBYTES
370 , .p_ntxsegs = 16
371 , .p_ntxsegs_alloc = SIP_NTXSEGS_ALLOC
372 , .p_nrxdesc = SIP_NRXDESC
373 , .p_bits = {
374 .b_txcfg_mxdma_8 = 0x00200000 /* 8 bytes */
375 , .b_txcfg_mxdma_16 = 0x00300000 /* 16 bytes */
376 , .b_txcfg_mxdma_32 = 0x00400000 /* 32 bytes */
377 , .b_txcfg_mxdma_64 = 0x00500000 /* 64 bytes */
378 , .b_txcfg_mxdma_128 = 0x00600000 /* 128 bytes */
379 , .b_txcfg_mxdma_256 = 0x00700000 /* 256 bytes */
380 , .b_txcfg_mxdma_512 = 0x00000000 /* 512 bytes */
381 , .b_txcfg_flth_mask = 0x00003f00 /* Tx fill threshold */
382 , .b_txcfg_drth_mask = 0x0000003f /* Tx drain threshold */
383
384 , .b_rxcfg_mxdma_8 = 0x00200000 /* 8 bytes */
385 , .b_rxcfg_mxdma_16 = 0x00300000 /* 16 bytes */
386 , .b_rxcfg_mxdma_32 = 0x00400000 /* 32 bytes */
387 , .b_rxcfg_mxdma_64 = 0x00500000 /* 64 bytes */
388 , .b_rxcfg_mxdma_128 = 0x00600000 /* 128 bytes */
389 , .b_rxcfg_mxdma_256 = 0x00700000 /* 256 bytes */
390 , .b_rxcfg_mxdma_512 = 0x00000000 /* 512 bytes */
391
392 , .b_isr_txrcmp = 0x02000000 /* transmit reset complete */
393 , .b_isr_rxrcmp = 0x01000000 /* receive reset complete */
394 , .b_isr_dperr = 0x00800000 /* detected parity error */
395 , .b_isr_sserr = 0x00400000 /* signalled system error */
396 , .b_isr_rmabt = 0x00200000 /* received master abort */
397 , .b_isr_rtabt = 0x00100000 /* received target abort */
398 , .b_cmdsts_size_mask = OTHER_CMDSTS_SIZE_MASK
399 }
400 , .p_regs = {
401 .r_rxcfg = OTHER_SIP_RXCFG,
402 .r_txcfg = OTHER_SIP_TXCFG
403 }
404 }, gsip_parm = {
405 .p_filtmem = DP83820_RFCR_NS_RFADDR_FILTMEM
406 , .p_rxbuf_len = MCLBYTES - 8
407 , .p_tx_dmamap_size = ETHER_MAX_LEN_JUMBO
408 , .p_ntxsegs = 64
409 , .p_ntxsegs_alloc = GSIP_NTXSEGS_ALLOC
410 , .p_nrxdesc = GSIP_NRXDESC
411 , .p_bits = {
412 .b_txcfg_mxdma_8 = 0x00100000 /* 8 bytes */
413 , .b_txcfg_mxdma_16 = 0x00200000 /* 16 bytes */
414 , .b_txcfg_mxdma_32 = 0x00300000 /* 32 bytes */
415 , .b_txcfg_mxdma_64 = 0x00400000 /* 64 bytes */
416 , .b_txcfg_mxdma_128 = 0x00500000 /* 128 bytes */
417 , .b_txcfg_mxdma_256 = 0x00600000 /* 256 bytes */
418 , .b_txcfg_mxdma_512 = 0x00700000 /* 512 bytes */
419 , .b_txcfg_flth_mask = 0x0000ff00 /* Fx fill threshold */
420 , .b_txcfg_drth_mask = 0x000000ff /* Tx drain threshold */
421
422 , .b_rxcfg_mxdma_8 = 0x00100000 /* 8 bytes */
423 , .b_rxcfg_mxdma_16 = 0x00200000 /* 16 bytes */
424 , .b_rxcfg_mxdma_32 = 0x00300000 /* 32 bytes */
425 , .b_rxcfg_mxdma_64 = 0x00400000 /* 64 bytes */
426 , .b_rxcfg_mxdma_128 = 0x00500000 /* 128 bytes */
427 , .b_rxcfg_mxdma_256 = 0x00600000 /* 256 bytes */
428 , .b_rxcfg_mxdma_512 = 0x00700000 /* 512 bytes */
429
430 , .b_isr_txrcmp = 0x00400000 /* transmit reset complete */
431 , .b_isr_rxrcmp = 0x00200000 /* receive reset complete */
432 , .b_isr_dperr = 0x00100000 /* detected parity error */
433 , .b_isr_sserr = 0x00080000 /* signalled system error */
434 , .b_isr_rmabt = 0x00040000 /* received master abort */
435 , .b_isr_rtabt = 0x00020000 /* received target abort */
436 , .b_cmdsts_size_mask = DP83820_CMDSTS_SIZE_MASK
437 }
438 , .p_regs = {
439 .r_rxcfg = DP83820_SIP_RXCFG,
440 .r_txcfg = DP83820_SIP_TXCFG
441 }
442 };
443
444 static inline int
sip_nexttx(const struct sip_softc * sc,int x)445 sip_nexttx(const struct sip_softc *sc, int x)
446 {
447 return (x + 1) & sc->sc_ntxdesc_mask;
448 }
449
450 static inline int
sip_nextrx(const struct sip_softc * sc,int x)451 sip_nextrx(const struct sip_softc *sc, int x)
452 {
453 return (x + 1) & sc->sc_nrxdesc_mask;
454 }
455
456 /* 83820 only */
457 static inline void
sip_rxchain_reset(struct sip_softc * sc)458 sip_rxchain_reset(struct sip_softc *sc)
459 {
460 sc->sc_rxtailp = &sc->sc_rxhead;
461 *sc->sc_rxtailp = NULL;
462 sc->sc_rxlen = 0;
463 }
464
465 /* 83820 only */
466 static inline void
sip_rxchain_link(struct sip_softc * sc,struct mbuf * m)467 sip_rxchain_link(struct sip_softc *sc, struct mbuf *m)
468 {
469 *sc->sc_rxtailp = sc->sc_rxtail = m;
470 sc->sc_rxtailp = &m->m_next;
471 }
472
473 #ifdef SIP_EVENT_COUNTERS
474 #define SIP_EVCNT_INCR(ev) (ev)->ev_count++
475 #else
476 #define SIP_EVCNT_INCR(ev) /* nothing */
477 #endif
478
479 #define SIP_CDTXADDR(sc, x) ((sc)->sc_cddma + SIP_CDTXOFF((x)))
480 #define SIP_CDRXADDR(sc, x) ((sc)->sc_cddma + SIP_CDRXOFF((x)))
481
482 static inline void
sip_set_rxdp(struct sip_softc * sc,bus_addr_t addr)483 sip_set_rxdp(struct sip_softc *sc, bus_addr_t addr)
484 {
485 if (sc->sc_gigabit)
486 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_RXDP_HI,
487 BUS_ADDR_HI32(addr));
488 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_RXDP, BUS_ADDR_LO32(addr));
489 }
490
491 static inline void
sip_set_txdp(struct sip_softc * sc,bus_addr_t addr)492 sip_set_txdp(struct sip_softc *sc, bus_addr_t addr)
493 {
494 if (sc->sc_gigabit)
495 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_TXDP_HI,
496 BUS_ADDR_HI32(addr));
497 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_TXDP, BUS_ADDR_LO32(addr));
498 }
499
500 static inline void
sip_cdtxsync(struct sip_softc * sc,const int x0,const int n0,const int ops)501 sip_cdtxsync(struct sip_softc *sc, const int x0, const int n0, const int ops)
502 {
503 int x, n;
504
505 x = x0;
506 n = n0;
507
508 /* If it will wrap around, sync to the end of the ring. */
509 if (x + n > sc->sc_ntxdesc) {
510 bus_dmamap_sync(sc->sc_dmat, sc->sc_cddmamap,
511 SIP_CDTXOFF(x), sizeof(struct sip_desc) *
512 (sc->sc_ntxdesc - x), ops);
513 n -= (sc->sc_ntxdesc - x);
514 x = 0;
515 }
516
517 /* Now sync whatever is left. */
518 bus_dmamap_sync(sc->sc_dmat, sc->sc_cddmamap,
519 SIP_CDTXOFF(x), sizeof(struct sip_desc) * n, ops);
520 }
521
522 static inline void
sip_cdrxsync(struct sip_softc * sc,int x,int ops)523 sip_cdrxsync(struct sip_softc *sc, int x, int ops)
524 {
525 bus_dmamap_sync(sc->sc_dmat, sc->sc_cddmamap,
526 SIP_CDRXOFF(x), sizeof(struct sip_desc), ops);
527 }
528
529 static void
sip_init_txring(struct sip_softc * sc)530 sip_init_txring(struct sip_softc *sc)
531 {
532 struct sip_desc *sipd;
533 bus_addr_t next_desc;
534 int i;
535
536 memset(sc->sc_txdescs, 0, sizeof(sc->sc_txdescs));
537 for (i = 0; i < sc->sc_ntxdesc; i++) {
538 sipd = &sc->sc_txdescs[i];
539 next_desc = SIP_CDTXADDR(sc, sip_nexttx(sc, i));
540 if (sc->sc_dma64) {
541 sipd->sipd_words[GSIP64_DESC_LINK_LO] =
542 htole32(BUS_ADDR_LO32(next_desc));
543 sipd->sipd_words[GSIP64_DESC_LINK_HI] =
544 htole32(BUS_ADDR_HI32(next_desc));
545 } else {
546 /* SIP_DESC_LINK == GSIP_DESC_LINK */
547 sipd->sipd_words[SIP_DESC_LINK] = htole32(next_desc);
548 }
549 }
550 sip_cdtxsync(sc, 0, sc->sc_ntxdesc,
551 BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE);
552 sc->sc_txfree = sc->sc_ntxdesc;
553 sc->sc_txnext = 0;
554 sc->sc_txwin = 0;
555 }
556
557 static inline void
sip_init_txdesc(struct sip_softc * sc,int x,bus_addr_t bufptr,uint32_t cmdsts)558 sip_init_txdesc(struct sip_softc *sc, int x, bus_addr_t bufptr, uint32_t cmdsts)
559 {
560 struct sip_desc *sipd = &sc->sc_txdescs[x];
561
562 if (sc->sc_dma64) {
563 sipd->sipd_words[GSIP64_DESC_BUFPTR_LO] =
564 htole32(BUS_ADDR_LO32(bufptr));
565 sipd->sipd_words[GSIP64_DESC_BUFPTR_HI] =
566 htole32(BUS_ADDR_HI32(bufptr));
567 } else {
568 sipd->sipd_words[sc->sc_bufptr_idx] = htole32(bufptr);
569 }
570 sipd->sipd_words[sc->sc_extsts_idx] = 0;
571 sipd->sipd_words[sc->sc_cmdsts_idx] = htole32(cmdsts);
572 /* sip_cdtxsync() will be done later. */
573 }
574
575 static inline void
sip_init_rxdesc(struct sip_softc * sc,int x)576 sip_init_rxdesc(struct sip_softc *sc, int x)
577 {
578 struct sip_rxsoft *rxs = &sc->sc_rxsoft[x];
579 struct sip_desc *sipd = &sc->sc_rxdescs[x];
580 const bus_addr_t next_desc = SIP_CDRXADDR(sc, sip_nextrx(sc, x));
581
582 if (sc->sc_dma64) {
583 sipd->sipd_words[GSIP64_DESC_LINK_LO] =
584 htole32(BUS_ADDR_LO32(next_desc));
585 sipd->sipd_words[GSIP64_DESC_LINK_HI] =
586 htole32(BUS_ADDR_HI32(next_desc));
587 sipd->sipd_words[GSIP64_DESC_BUFPTR_LO] =
588 htole32(BUS_ADDR_LO32(rxs->rxs_dmamap->dm_segs[0].ds_addr));
589 sipd->sipd_words[GSIP64_DESC_BUFPTR_HI] =
590 htole32(BUS_ADDR_HI32(rxs->rxs_dmamap->dm_segs[0].ds_addr));
591 } else {
592 sipd->sipd_words[SIP_DESC_LINK] = htole32(next_desc);
593 sipd->sipd_words[sc->sc_bufptr_idx] =
594 htole32(rxs->rxs_dmamap->dm_segs[0].ds_addr);
595 }
596 sipd->sipd_words[sc->sc_extsts_idx] = 0;
597 sip_cdrxsync(sc, x, BUS_DMASYNC_PREWRITE);
598 sipd->sipd_words[sc->sc_cmdsts_idx] =
599 htole32(CMDSTS_INTR | (sc->sc_parm->p_rxbuf_len &
600 sc->sc_bits.b_cmdsts_size_mask));
601 sip_cdrxsync(sc, x, BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE);
602 }
603
604 #define SIP_CHIP_VERS(sc, v, p, r) \
605 ((sc)->sc_model->sip_vendor == (v) && \
606 (sc)->sc_model->sip_product == (p) && \
607 (sc)->sc_rev == (r))
608
609 #define SIP_CHIP_MODEL(sc, v, p) \
610 ((sc)->sc_model->sip_vendor == (v) && \
611 (sc)->sc_model->sip_product == (p))
612
613 #define SIP_SIS900_REV(sc, rev) \
614 SIP_CHIP_VERS((sc), PCI_VENDOR_SIS, PCI_PRODUCT_SIS_900, (rev))
615
616 #define SIP_TIMEOUT 1000
617
618 static int sip_ifflags_cb(struct ethercom *);
619 static void sipcom_start(struct ifnet *);
620 static void sipcom_watchdog(struct ifnet *);
621 static int sipcom_ioctl(struct ifnet *, u_long, void *);
622 static int sipcom_init(struct ifnet *);
623 static void sipcom_stop(struct ifnet *, int);
624
625 static bool sipcom_reset(struct sip_softc *);
626 static void sipcom_rxdrain(struct sip_softc *);
627 static int sipcom_add_rxbuf(struct sip_softc *, int);
628 static void sipcom_read_eeprom(struct sip_softc *, int, int,
629 uint16_t *);
630 static void sipcom_tick(void *);
631
632 static void sipcom_sis900_set_filter(struct sip_softc *);
633 static void sipcom_dp83815_set_filter(struct sip_softc *);
634
635 static void sipcom_dp83820_read_macaddr(struct sip_softc *,
636 const struct pci_attach_args *, uint8_t *);
637 static void sipcom_sis900_eeprom_delay(struct sip_softc *sc);
638 static void sipcom_sis900_read_macaddr(struct sip_softc *,
639 const struct pci_attach_args *, uint8_t *);
640 static void sipcom_dp83815_read_macaddr(struct sip_softc *,
641 const struct pci_attach_args *, uint8_t *);
642
643 static int sipcom_intr(void *);
644 static void sipcom_txintr(struct sip_softc *);
645 static void sip_rxintr(struct sip_softc *);
646 static void gsip_rxintr(struct sip_softc *);
647
648 static int sipcom_dp83820_mii_readreg(device_t, int, int, uint16_t *);
649 static int sipcom_dp83820_mii_writereg(device_t, int, int, uint16_t);
650 static void sipcom_dp83820_mii_statchg(struct ifnet *);
651
652 static int sipcom_sis900_mii_readreg(device_t, int, int, uint16_t *);
653 static int sipcom_sis900_mii_writereg(device_t, int, int, uint16_t);
654 static void sipcom_sis900_mii_statchg(struct ifnet *);
655
656 static int sipcom_dp83815_mii_readreg(device_t, int, int, uint16_t *);
657 static int sipcom_dp83815_mii_writereg(device_t, int, int, uint16_t);
658 static void sipcom_dp83815_mii_statchg(struct ifnet *);
659
660 static void sipcom_mediastatus(struct ifnet *, struct ifmediareq *);
661
662 static int sipcom_match(device_t, cfdata_t, void *);
663 static void sipcom_attach(device_t, device_t, void *);
664 static void sipcom_do_detach(device_t, enum sip_attach_stage);
665 static int sipcom_detach(device_t, int);
666 static bool sipcom_resume(device_t, const pmf_qual_t *);
667 static bool sipcom_suspend(device_t, const pmf_qual_t *);
668
669 int gsip_copy_small = 0;
670 int sip_copy_small = 0;
671
672 CFATTACH_DECL3_NEW(gsip, sizeof(struct sip_softc),
673 sipcom_match, sipcom_attach, sipcom_detach, NULL, NULL, NULL,
674 DVF_DETACH_SHUTDOWN);
675 CFATTACH_DECL3_NEW(sip, sizeof(struct sip_softc),
676 sipcom_match, sipcom_attach, sipcom_detach, NULL, NULL, NULL,
677 DVF_DETACH_SHUTDOWN);
678
679 /*
680 * Descriptions of the variants of the SiS900.
681 */
682 struct sip_variant {
683 int (*sipv_mii_readreg)(device_t, int, int, uint16_t *);
684 int (*sipv_mii_writereg)(device_t, int, int, uint16_t);
685 void (*sipv_mii_statchg)(struct ifnet *);
686 void (*sipv_set_filter)(struct sip_softc *);
687 void (*sipv_read_macaddr)(struct sip_softc *,
688 const struct pci_attach_args *, uint8_t *);
689 };
690
691 static uint32_t sipcom_mii_bitbang_read(device_t);
692 static void sipcom_mii_bitbang_write(device_t, uint32_t);
693
694 static const struct mii_bitbang_ops sipcom_mii_bitbang_ops = {
695 sipcom_mii_bitbang_read,
696 sipcom_mii_bitbang_write,
697 {
698 EROMAR_MDIO, /* MII_BIT_MDO */
699 EROMAR_MDIO, /* MII_BIT_MDI */
700 EROMAR_MDC, /* MII_BIT_MDC */
701 EROMAR_MDDIR, /* MII_BIT_DIR_HOST_PHY */
702 0, /* MII_BIT_DIR_PHY_HOST */
703 }
704 };
705
706 static const struct sip_variant sipcom_variant_dp83820 = {
707 sipcom_dp83820_mii_readreg,
708 sipcom_dp83820_mii_writereg,
709 sipcom_dp83820_mii_statchg,
710 sipcom_dp83815_set_filter,
711 sipcom_dp83820_read_macaddr,
712 };
713
714 static const struct sip_variant sipcom_variant_sis900 = {
715 sipcom_sis900_mii_readreg,
716 sipcom_sis900_mii_writereg,
717 sipcom_sis900_mii_statchg,
718 sipcom_sis900_set_filter,
719 sipcom_sis900_read_macaddr,
720 };
721
722 static const struct sip_variant sipcom_variant_dp83815 = {
723 sipcom_dp83815_mii_readreg,
724 sipcom_dp83815_mii_writereg,
725 sipcom_dp83815_mii_statchg,
726 sipcom_dp83815_set_filter,
727 sipcom_dp83815_read_macaddr,
728 };
729
730
731 /*
732 * Devices supported by this driver.
733 */
734 static const struct sip_product {
735 pci_vendor_id_t sip_vendor;
736 pci_product_id_t sip_product;
737 const char *sip_name;
738 const struct sip_variant *sip_variant;
739 bool sip_gigabit;
740 } sipcom_products[] = {
741 { PCI_VENDOR_NS, PCI_PRODUCT_NS_DP83820,
742 "NatSemi DP83820 Gigabit Ethernet",
743 &sipcom_variant_dp83820, true },
744
745 { PCI_VENDOR_SIS, PCI_PRODUCT_SIS_900,
746 "SiS 900 10/100 Ethernet",
747 &sipcom_variant_sis900, false },
748 { PCI_VENDOR_SIS, PCI_PRODUCT_SIS_7016,
749 "SiS 7016 10/100 Ethernet",
750 &sipcom_variant_sis900, false },
751
752 { PCI_VENDOR_NS, PCI_PRODUCT_NS_DP83815,
753 "NatSemi DP83815 10/100 Ethernet",
754 &sipcom_variant_dp83815, false },
755
756 { 0, 0,
757 NULL,
758 NULL, false },
759 };
760
761 static const struct sip_product *
sipcom_lookup(const struct pci_attach_args * pa,bool gigabit)762 sipcom_lookup(const struct pci_attach_args *pa, bool gigabit)
763 {
764 const struct sip_product *sip;
765
766 for (sip = sipcom_products; sip->sip_name != NULL; sip++) {
767 if (PCI_VENDOR(pa->pa_id) == sip->sip_vendor &&
768 PCI_PRODUCT(pa->pa_id) == sip->sip_product &&
769 sip->sip_gigabit == gigabit)
770 return sip;
771 }
772 return NULL;
773 }
774
775 /*
776 * I really hate stupid hardware vendors. There's a bit in the EEPROM
777 * which indicates if the card can do 64-bit data transfers. Unfortunately,
778 * several vendors of 32-bit cards fail to clear this bit in the EEPROM,
779 * which means we try to use 64-bit data transfers on those cards if we
780 * happen to be plugged into a 32-bit slot.
781 *
782 * What we do is use this table of cards known to be 64-bit cards. If
783 * you have a 64-bit card who's subsystem ID is not listed in this table,
784 * send the output of "pcictl dump ..." of the device to me so that your
785 * card will use the 64-bit data path when plugged into a 64-bit slot.
786 *
787 * -- Jason R. Thorpe <thorpej@NetBSD.org>
788 * June 30, 2002
789 */
790 static int
sipcom_check_64bit(const struct pci_attach_args * pa)791 sipcom_check_64bit(const struct pci_attach_args *pa)
792 {
793 static const struct {
794 pci_vendor_id_t c64_vendor;
795 pci_product_id_t c64_product;
796 } card64[] = {
797 /* Asante GigaNIX */
798 { 0x128a, 0x0002 },
799
800 /* Accton EN1407-T, Planex GN-1000TE */
801 { 0x1113, 0x1407 },
802
803 /* Netgear GA621 */
804 { 0x1385, 0x621a },
805
806 /* Netgear GA622 */
807 { 0x1385, 0x622a },
808
809 /* SMC EZ Card 1000 (9462TX) */
810 { 0x10b8, 0x9462 },
811
812 { 0, 0}
813 };
814 pcireg_t subsys;
815 int i;
816
817 subsys = pci_conf_read(pa->pa_pc, pa->pa_tag, PCI_SUBSYS_ID_REG);
818
819 for (i = 0; card64[i].c64_vendor != 0; i++) {
820 if (PCI_VENDOR(subsys) == card64[i].c64_vendor &&
821 PCI_PRODUCT(subsys) == card64[i].c64_product)
822 return 1;
823 }
824
825 return 0;
826 }
827
828 static int
sipcom_match(device_t parent,cfdata_t cf,void * aux)829 sipcom_match(device_t parent, cfdata_t cf, void *aux)
830 {
831 struct pci_attach_args *pa = aux;
832
833 if (sipcom_lookup(pa, strcmp(cf->cf_name, "gsip") == 0) != NULL)
834 return 1;
835
836 return 0;
837 }
838
839 static void
sipcom_dp83820_attach(struct sip_softc * sc,struct pci_attach_args * pa)840 sipcom_dp83820_attach(struct sip_softc *sc, struct pci_attach_args *pa)
841 {
842 uint32_t reg;
843 int i;
844
845 /*
846 * Cause the chip to load configuration data from the EEPROM.
847 */
848 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_PTSCR, PTSCR_EELOAD_EN);
849 for (i = 0; i < 10000; i++) {
850 delay(10);
851 if ((bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_PTSCR) &
852 PTSCR_EELOAD_EN) == 0)
853 break;
854 }
855 if (bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_PTSCR) &
856 PTSCR_EELOAD_EN) {
857 printf("%s: timeout loading configuration from EEPROM\n",
858 device_xname(sc->sc_dev));
859 return;
860 }
861
862 sc->sc_gpior = bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_GPIOR);
863
864 reg = bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_CFG);
865 if (reg & CFG_PCI64_DET) {
866 const char *using64 = NULL;
867
868 if (reg & CFG_DATA64_EN) {
869 /*
870 * Check to see if this card is 64-bit. If so,
871 * enable 64-bit data transfers.
872 *
873 * We can't trust the DATA64_EN bit in the EEPROM,
874 * because vendors of 32-bit cards fail to clear
875 * that bit in many cases (yet the card still detects
876 * that it's in a 64-bit slot because I guess they
877 * wired up ACK64# and REQ64#).
878 */
879 if (gsip_disable_data64)
880 using64 = "force-disabled";
881 else if (sipcom_check_64bit(pa)) {
882 sc->sc_cfg |= CFG_DATA64_EN;
883 using64 = "enabled";
884 } else
885 using64 = "disabled (32-bit card)";
886 } else {
887 using64 = "disabled in EEPROM";
888 }
889 printf("%s: 64-bit slot detected, 64-bit transfers %s\n",
890 device_xname(sc->sc_dev), using64);
891 }
892
893 /*
894 * The T64ADDR bit is loaded by the chip from the EEPROM and
895 * is read-only.
896 */
897 if (reg & CFG_T64ADDR)
898 sc->sc_cfg |= CFG_T64ADDR;
899
900 /*
901 * We can use 64-bit DMA addressing regardless of what
902 * sort of slot we're in.
903 */
904 if (pci_dma64_available(pa)) {
905 sc->sc_dmat = pa->pa_dmat64;
906 sc->sc_cfg |= CFG_M64ADDR;
907 sc->sc_dma64 = true;
908 }
909
910 if (reg & (CFG_TBI_EN | CFG_EXT_125)) {
911 const char *sep = "";
912 printf("%s: using ", device_xname(sc->sc_dev));
913 if (reg & CFG_EXT_125) {
914 sc->sc_cfg |= CFG_EXT_125;
915 printf("%sexternal 125MHz clock", sep);
916 sep = ", ";
917 }
918 if (reg & CFG_TBI_EN) {
919 sc->sc_cfg |= CFG_TBI_EN;
920 printf("%sten-bit interface", sep);
921 sep = ", ";
922 }
923 printf("\n");
924 }
925 if ((pa->pa_flags & PCI_FLAGS_MRM_OKAY) == 0 ||
926 (reg & CFG_MRM_DIS) != 0)
927 sc->sc_cfg |= CFG_MRM_DIS;
928 if ((pa->pa_flags & PCI_FLAGS_MWI_OKAY) == 0 ||
929 (reg & CFG_MWI_DIS) != 0)
930 sc->sc_cfg |= CFG_MWI_DIS;
931
932 /*
933 * Use the extended descriptor format on the DP83820. This
934 * gives us an interface to VLAN tagging and IPv4/TCP/UDP
935 * checksumming.
936 */
937 sc->sc_cfg |= CFG_EXTSTS_EN;
938 }
939
940 static int
sipcom_detach(device_t self,int flags)941 sipcom_detach(device_t self, int flags)
942 {
943 int s;
944
945 s = splnet();
946 sipcom_do_detach(self, SIP_ATTACH_FIN);
947 splx(s);
948
949 return 0;
950 }
951
952 static void
sipcom_do_detach(device_t self,enum sip_attach_stage stage)953 sipcom_do_detach(device_t self, enum sip_attach_stage stage)
954 {
955 int i;
956 struct sip_softc *sc = device_private(self);
957 struct ifnet *ifp = &sc->sc_ethercom.ec_if;
958
959 /*
960 * Free any resources we've allocated during attach.
961 * Do this in reverse order and fall through.
962 */
963 switch (stage) {
964 case SIP_ATTACH_FIN:
965 sipcom_stop(ifp, 1);
966 pmf_device_deregister(self);
967 #ifdef SIP_EVENT_COUNTERS
968 /*
969 * Attach event counters.
970 */
971 evcnt_detach(&sc->sc_ev_txforceintr);
972 evcnt_detach(&sc->sc_ev_txdstall);
973 evcnt_detach(&sc->sc_ev_hiberr);
974 evcnt_detach(&sc->sc_ev_rxintr);
975 evcnt_detach(&sc->sc_ev_txiintr);
976 evcnt_detach(&sc->sc_ev_txdintr);
977 if (!sc->sc_gigabit) {
978 evcnt_detach(&sc->sc_ev_rxpause);
979 } else {
980 evcnt_detach(&sc->sc_ev_txudpsum);
981 evcnt_detach(&sc->sc_ev_txtcpsum);
982 evcnt_detach(&sc->sc_ev_txipsum);
983 evcnt_detach(&sc->sc_ev_rxudpsum);
984 evcnt_detach(&sc->sc_ev_rxtcpsum);
985 evcnt_detach(&sc->sc_ev_rxipsum);
986 evcnt_detach(&sc->sc_ev_txpause);
987 evcnt_detach(&sc->sc_ev_rxpause);
988 }
989 #endif /* SIP_EVENT_COUNTERS */
990
991 rnd_detach_source(&sc->rnd_source);
992
993 ether_ifdetach(ifp);
994 if_detach(ifp);
995 mii_detach(&sc->sc_mii, MII_PHY_ANY, MII_OFFSET_ANY);
996 ifmedia_fini(&sc->sc_mii.mii_media);
997
998 /*FALLTHROUGH*/
999 case SIP_ATTACH_CREATE_RXMAP:
1000 for (i = 0; i < sc->sc_parm->p_nrxdesc; i++) {
1001 if (sc->sc_rxsoft[i].rxs_dmamap != NULL)
1002 bus_dmamap_destroy(sc->sc_dmat,
1003 sc->sc_rxsoft[i].rxs_dmamap);
1004 }
1005 /*FALLTHROUGH*/
1006 case SIP_ATTACH_CREATE_TXMAP:
1007 for (i = 0; i < SIP_TXQUEUELEN; i++) {
1008 if (sc->sc_txsoft[i].txs_dmamap != NULL)
1009 bus_dmamap_destroy(sc->sc_dmat,
1010 sc->sc_txsoft[i].txs_dmamap);
1011 }
1012 /*FALLTHROUGH*/
1013 case SIP_ATTACH_LOAD_MAP:
1014 bus_dmamap_unload(sc->sc_dmat, sc->sc_cddmamap);
1015 /*FALLTHROUGH*/
1016 case SIP_ATTACH_CREATE_MAP:
1017 bus_dmamap_destroy(sc->sc_dmat, sc->sc_cddmamap);
1018 /*FALLTHROUGH*/
1019 case SIP_ATTACH_MAP_MEM:
1020 bus_dmamem_unmap(sc->sc_dmat, (void *)sc->sc_control_data,
1021 sizeof(struct sip_control_data));
1022 /*FALLTHROUGH*/
1023 case SIP_ATTACH_ALLOC_MEM:
1024 bus_dmamem_free(sc->sc_dmat, &sc->sc_seg, 1);
1025 /* FALLTHROUGH*/
1026 case SIP_ATTACH_INTR:
1027 pci_intr_disestablish(sc->sc_pc, sc->sc_ih);
1028 /* FALLTHROUGH*/
1029 case SIP_ATTACH_MAP:
1030 bus_space_unmap(sc->sc_st, sc->sc_sh, sc->sc_sz);
1031 break;
1032 default:
1033 break;
1034 }
1035 return;
1036 }
1037
1038 static bool
sipcom_resume(device_t self,const pmf_qual_t * qual)1039 sipcom_resume(device_t self, const pmf_qual_t *qual)
1040 {
1041 struct sip_softc *sc = device_private(self);
1042
1043 return sipcom_reset(sc);
1044 }
1045
1046 static bool
sipcom_suspend(device_t self,const pmf_qual_t * qual)1047 sipcom_suspend(device_t self, const pmf_qual_t *qual)
1048 {
1049 struct sip_softc *sc = device_private(self);
1050
1051 sipcom_rxdrain(sc);
1052 return true;
1053 }
1054
1055 static void
sipcom_attach(device_t parent,device_t self,void * aux)1056 sipcom_attach(device_t parent, device_t self, void *aux)
1057 {
1058 struct sip_softc *sc = device_private(self);
1059 struct pci_attach_args *pa = aux;
1060 struct ifnet *ifp = &sc->sc_ethercom.ec_if;
1061 struct mii_data * const mii = &sc->sc_mii;
1062 pci_chipset_tag_t pc = pa->pa_pc;
1063 pci_intr_handle_t ih;
1064 const char *intrstr = NULL;
1065 bus_space_tag_t iot, memt;
1066 bus_space_handle_t ioh, memh;
1067 bus_size_t iosz, memsz;
1068 int ioh_valid, memh_valid;
1069 int i, rseg, error;
1070 const struct sip_product *sip;
1071 uint8_t enaddr[ETHER_ADDR_LEN];
1072 pcireg_t csr;
1073 pcireg_t memtype;
1074 bus_size_t tx_dmamap_size;
1075 int ntxsegs_alloc;
1076 cfdata_t cf = device_cfdata(self);
1077 char intrbuf[PCI_INTRSTR_LEN];
1078
1079 callout_init(&sc->sc_tick_ch, 0);
1080 callout_setfunc(&sc->sc_tick_ch, sipcom_tick, sc);
1081
1082 sip = sipcom_lookup(pa, strcmp(cf->cf_name, "gsip") == 0);
1083 if (sip == NULL) {
1084 aprint_error("\n");
1085 panic("%s: impossible", __func__);
1086 }
1087 sc->sc_dev = self;
1088 sc->sc_gigabit = sip->sip_gigabit;
1089 sc->sc_dma64 = false;
1090 pmf_self_suspensor_init(self, &sc->sc_suspensor, &sc->sc_qual);
1091 sc->sc_pc = pc;
1092
1093 if (sc->sc_gigabit) {
1094 if (sc->sc_dma64) {
1095 sc->sc_bufptr_idx = GSIP64_DESC_BUFPTR_LO;
1096 sc->sc_cmdsts_idx = GSIP64_DESC_CMDSTS;
1097 sc->sc_extsts_idx = GSIP64_DESC_EXTSTS;
1098 } else {
1099 sc->sc_bufptr_idx = GSIP_DESC_BUFPTR;
1100 sc->sc_cmdsts_idx = GSIP_DESC_CMDSTS;
1101 sc->sc_extsts_idx = GSIP_DESC_EXTSTS;
1102 }
1103 sc->sc_rxintr = gsip_rxintr;
1104 sc->sc_parm = &gsip_parm;
1105 } else {
1106 sc->sc_rxintr = sip_rxintr;
1107 sc->sc_parm = &sip_parm;
1108 sc->sc_bufptr_idx = SIP_DESC_BUFPTR;
1109 sc->sc_cmdsts_idx = SIP_DESC_CMDSTS;
1110 /*
1111 * EXTSTS doesn't really exist on non-GigE parts,
1112 * but we initialize the index for simplicity later.
1113 */
1114 sc->sc_extsts_idx = GSIP_DESC_EXTSTS;
1115 }
1116 tx_dmamap_size = sc->sc_parm->p_tx_dmamap_size;
1117 ntxsegs_alloc = sc->sc_parm->p_ntxsegs_alloc;
1118 sc->sc_ntxdesc = SIP_TXQUEUELEN * ntxsegs_alloc;
1119 sc->sc_ntxdesc_mask = sc->sc_ntxdesc - 1;
1120 sc->sc_nrxdesc_mask = sc->sc_parm->p_nrxdesc - 1;
1121
1122 sc->sc_rev = PCI_REVISION(pa->pa_class);
1123
1124 aprint_naive("\n");
1125 aprint_normal(": %s, rev %#02x\n", sip->sip_name, sc->sc_rev);
1126
1127 sc->sc_model = sip;
1128
1129 /*
1130 * XXX Work-around broken PXE firmware on some boards.
1131 *
1132 * The DP83815 shares an address decoder with the MEM BAR
1133 * and the ROM BAR. Make sure the ROM BAR is disabled,
1134 * so that memory mapped access works.
1135 */
1136 pci_conf_write(pa->pa_pc, pa->pa_tag, PCI_MAPREG_ROM,
1137 pci_conf_read(pa->pa_pc, pa->pa_tag, PCI_MAPREG_ROM) &
1138 ~PCI_MAPREG_ROM_ENABLE);
1139
1140 /*
1141 * Map the device.
1142 */
1143 ioh_valid = (pci_mapreg_map(pa, SIP_PCI_CFGIOA,
1144 PCI_MAPREG_TYPE_IO, 0,
1145 &iot, &ioh, NULL, &iosz) == 0);
1146 if (sc->sc_gigabit) {
1147 memtype = pci_mapreg_type(pa->pa_pc, pa->pa_tag, SIP_PCI_CFGMA);
1148 switch (memtype) {
1149 case PCI_MAPREG_TYPE_MEM | PCI_MAPREG_MEM_TYPE_32BIT:
1150 case PCI_MAPREG_TYPE_MEM | PCI_MAPREG_MEM_TYPE_64BIT:
1151 memh_valid = (pci_mapreg_map(pa, SIP_PCI_CFGMA,
1152 memtype, 0, &memt, &memh, NULL, &memsz) == 0);
1153 break;
1154 default:
1155 memh_valid = 0;
1156 }
1157 } else {
1158 memh_valid = (pci_mapreg_map(pa, SIP_PCI_CFGMA,
1159 PCI_MAPREG_TYPE_MEM | PCI_MAPREG_MEM_TYPE_32BIT, 0,
1160 &memt, &memh, NULL, &memsz) == 0);
1161 }
1162
1163 if (memh_valid) {
1164 sc->sc_st = memt;
1165 sc->sc_sh = memh;
1166 sc->sc_sz = memsz;
1167 } else if (ioh_valid) {
1168 sc->sc_st = iot;
1169 sc->sc_sh = ioh;
1170 sc->sc_sz = iosz;
1171 } else {
1172 aprint_error_dev(self, "unable to map device registers\n");
1173 return;
1174 }
1175
1176 sc->sc_dmat = pa->pa_dmat;
1177
1178 /*
1179 * Make sure bus mastering is enabled. Also make sure
1180 * Write/Invalidate is enabled if we're allowed to use it.
1181 */
1182 csr = pci_conf_read(pc, pa->pa_tag, PCI_COMMAND_STATUS_REG);
1183 if (pa->pa_flags & PCI_FLAGS_MWI_OKAY)
1184 csr |= PCI_COMMAND_INVALIDATE_ENABLE;
1185 pci_conf_write(pc, pa->pa_tag, PCI_COMMAND_STATUS_REG,
1186 csr | PCI_COMMAND_MASTER_ENABLE);
1187
1188 /* Power up chip */
1189 error = pci_activate(pa->pa_pc, pa->pa_tag, self, pci_activate_null);
1190 if (error != 0 && error != EOPNOTSUPP) {
1191 aprint_error_dev(sc->sc_dev, "cannot activate %d\n", error);
1192 return;
1193 }
1194
1195 /*
1196 * Map and establish our interrupt.
1197 */
1198 if (pci_intr_map(pa, &ih)) {
1199 aprint_error_dev(sc->sc_dev, "unable to map interrupt\n");
1200 return;
1201 }
1202 intrstr = pci_intr_string(pc, ih, intrbuf, sizeof(intrbuf));
1203 sc->sc_ih = pci_intr_establish_xname(pc, ih, IPL_NET, sipcom_intr, sc,
1204 device_xname(self));
1205 if (sc->sc_ih == NULL) {
1206 aprint_error_dev(sc->sc_dev, "unable to establish interrupt");
1207 if (intrstr != NULL)
1208 aprint_error(" at %s", intrstr);
1209 aprint_error("\n");
1210 sipcom_do_detach(self, SIP_ATTACH_MAP);
1211 return;
1212 }
1213 aprint_normal_dev(sc->sc_dev, "interrupting at %s\n", intrstr);
1214
1215 SIMPLEQ_INIT(&sc->sc_txfreeq);
1216 SIMPLEQ_INIT(&sc->sc_txdirtyq);
1217
1218 /*
1219 * Allocate the control data structures, and create and load the
1220 * DMA map for it.
1221 */
1222 if ((error = bus_dmamem_alloc(sc->sc_dmat,
1223 sizeof(struct sip_control_data), PAGE_SIZE, 0, &sc->sc_seg, 1,
1224 &rseg, 0)) != 0) {
1225 aprint_error_dev(sc->sc_dev,
1226 "unable to allocate control data, error = %d\n", error);
1227 sipcom_do_detach(self, SIP_ATTACH_INTR);
1228 return;
1229 }
1230
1231 if ((error = bus_dmamem_map(sc->sc_dmat, &sc->sc_seg, rseg,
1232 sizeof(struct sip_control_data), (void **)&sc->sc_control_data,
1233 BUS_DMA_COHERENT)) != 0) {
1234 aprint_error_dev(sc->sc_dev,
1235 "unable to map control data, error = %d\n", error);
1236 sipcom_do_detach(self, SIP_ATTACH_ALLOC_MEM);
1237 }
1238
1239 if ((error = bus_dmamap_create(sc->sc_dmat,
1240 sizeof(struct sip_control_data), 1,
1241 sizeof(struct sip_control_data), 0, 0, &sc->sc_cddmamap)) != 0) {
1242 aprint_error_dev(self, "unable to create control data DMA map"
1243 ", error = %d\n", error);
1244 sipcom_do_detach(self, SIP_ATTACH_MAP_MEM);
1245 }
1246
1247 if ((error = bus_dmamap_load(sc->sc_dmat, sc->sc_cddmamap,
1248 sc->sc_control_data, sizeof(struct sip_control_data), NULL,
1249 0)) != 0) {
1250 aprint_error_dev(self, "unable to load control data DMA map"
1251 ", error = %d\n", error);
1252 sipcom_do_detach(self, SIP_ATTACH_CREATE_MAP);
1253 }
1254
1255 /*
1256 * Create the transmit buffer DMA maps.
1257 */
1258 for (i = 0; i < SIP_TXQUEUELEN; i++) {
1259 if ((error = bus_dmamap_create(sc->sc_dmat, tx_dmamap_size,
1260 sc->sc_parm->p_ntxsegs, MCLBYTES, 0, 0,
1261 &sc->sc_txsoft[i].txs_dmamap)) != 0) {
1262 aprint_error_dev(self, "unable to create tx DMA map %d"
1263 ", error = %d\n", i, error);
1264 sipcom_do_detach(self, SIP_ATTACH_CREATE_TXMAP);
1265 }
1266 }
1267
1268 /*
1269 * Create the receive buffer DMA maps.
1270 */
1271 for (i = 0; i < sc->sc_parm->p_nrxdesc; i++) {
1272 if ((error = bus_dmamap_create(sc->sc_dmat, MCLBYTES, 1,
1273 MCLBYTES, 0, 0, &sc->sc_rxsoft[i].rxs_dmamap)) != 0) {
1274 aprint_error_dev(self, "unable to create rx DMA map %d"
1275 ", error = %d\n", i, error);
1276 sipcom_do_detach(self, SIP_ATTACH_CREATE_RXMAP);
1277 }
1278 sc->sc_rxsoft[i].rxs_mbuf = NULL;
1279 }
1280
1281 /*
1282 * Reset the chip to a known state.
1283 */
1284 sipcom_reset(sc);
1285
1286 /*
1287 * Read the Ethernet address from the EEPROM. This might
1288 * also fetch other stuff from the EEPROM and stash it
1289 * in the softc.
1290 */
1291 sc->sc_cfg = 0;
1292 if (!sc->sc_gigabit) {
1293 if (SIP_SIS900_REV(sc, SIS_REV_635) ||
1294 SIP_SIS900_REV(sc, SIS_REV_900B))
1295 sc->sc_cfg |= (CFG_PESEL | CFG_RNDCNT);
1296
1297 if (SIP_SIS900_REV(sc, SIS_REV_635) ||
1298 SIP_SIS900_REV(sc, SIS_REV_960) ||
1299 SIP_SIS900_REV(sc, SIS_REV_900B))
1300 sc->sc_cfg |=
1301 (bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_CFG) &
1302 CFG_EDBMASTEN);
1303 }
1304
1305 (*sip->sip_variant->sipv_read_macaddr)(sc, pa, enaddr);
1306
1307 aprint_normal_dev(self, "Ethernet address %s\n",ether_sprintf(enaddr));
1308
1309 /*
1310 * Initialize the configuration register: aggressive PCI
1311 * bus request algorithm, default backoff, default OW timer,
1312 * default parity error detection.
1313 *
1314 * NOTE: "Big endian mode" is useless on the SiS900 and
1315 * friends -- it affects packet data, not descriptors.
1316 */
1317 if (sc->sc_gigabit)
1318 sipcom_dp83820_attach(sc, pa);
1319
1320 /*
1321 * Initialize our media structures and probe the MII.
1322 */
1323 mii->mii_ifp = ifp;
1324 mii->mii_readreg = sip->sip_variant->sipv_mii_readreg;
1325 mii->mii_writereg = sip->sip_variant->sipv_mii_writereg;
1326 mii->mii_statchg = sip->sip_variant->sipv_mii_statchg;
1327 sc->sc_ethercom.ec_mii = mii;
1328 ifmedia_init(&mii->mii_media, IFM_IMASK, ether_mediachange,
1329 sipcom_mediastatus);
1330
1331 /*
1332 * XXX We cannot handle flow control on the DP83815.
1333 */
1334 if (SIP_CHIP_MODEL(sc, PCI_VENDOR_NS, PCI_PRODUCT_NS_DP83815))
1335 mii_attach(sc->sc_dev, mii, 0xffffffff, MII_PHY_ANY,
1336 MII_OFFSET_ANY, 0);
1337 else
1338 mii_attach(sc->sc_dev, mii, 0xffffffff, MII_PHY_ANY,
1339 MII_OFFSET_ANY, MIIF_DOPAUSE);
1340 if (LIST_FIRST(&mii->mii_phys) == NULL) {
1341 ifmedia_add(&mii->mii_media, IFM_ETHER | IFM_NONE, 0, NULL);
1342 ifmedia_set(&mii->mii_media, IFM_ETHER | IFM_NONE);
1343 } else
1344 ifmedia_set(&mii->mii_media, IFM_ETHER | IFM_AUTO);
1345
1346 ifp = &sc->sc_ethercom.ec_if;
1347 strlcpy(ifp->if_xname, device_xname(sc->sc_dev), IFNAMSIZ);
1348 ifp->if_softc = sc;
1349 ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST;
1350 sc->sc_if_flags = ifp->if_flags;
1351 ifp->if_ioctl = sipcom_ioctl;
1352 ifp->if_start = sipcom_start;
1353 ifp->if_watchdog = sipcom_watchdog;
1354 ifp->if_init = sipcom_init;
1355 ifp->if_stop = sipcom_stop;
1356 IFQ_SET_READY(&ifp->if_snd);
1357
1358 /*
1359 * We can support 802.1Q VLAN-sized frames.
1360 */
1361 sc->sc_ethercom.ec_capabilities |= ETHERCAP_VLAN_MTU;
1362
1363 if (sc->sc_gigabit) {
1364 /*
1365 * And the DP83820 can do VLAN tagging in hardware, and
1366 * support the jumbo Ethernet MTU.
1367 */
1368 sc->sc_ethercom.ec_capabilities |=
1369 ETHERCAP_VLAN_HWTAGGING | ETHERCAP_JUMBO_MTU;
1370 sc->sc_ethercom.ec_capenable |= ETHERCAP_VLAN_HWTAGGING;
1371
1372 /*
1373 * The DP83820 can do IPv4, TCPv4, and UDPv4 checksums
1374 * in hardware.
1375 */
1376 ifp->if_capabilities |=
1377 IFCAP_CSUM_IPv4_Tx | IFCAP_CSUM_IPv4_Rx |
1378 IFCAP_CSUM_TCPv4_Tx | IFCAP_CSUM_TCPv4_Rx |
1379 IFCAP_CSUM_UDPv4_Tx | IFCAP_CSUM_UDPv4_Rx;
1380 }
1381
1382 /*
1383 * Attach the interface.
1384 */
1385 if_attach(ifp);
1386 if_deferred_start_init(ifp, NULL);
1387 ether_ifattach(ifp, enaddr);
1388 ether_set_ifflags_cb(&sc->sc_ethercom, sip_ifflags_cb);
1389 sc->sc_prev.ec_capenable = sc->sc_ethercom.ec_capenable;
1390 sc->sc_prev.is_vlan = VLAN_ATTACHED(&(sc)->sc_ethercom);
1391 sc->sc_prev.if_capenable = ifp->if_capenable;
1392 rnd_attach_source(&sc->rnd_source, device_xname(sc->sc_dev),
1393 RND_TYPE_NET, RND_FLAG_DEFAULT);
1394
1395 /*
1396 * The number of bytes that must be available in
1397 * the Tx FIFO before the bus master can DMA more
1398 * data into the FIFO.
1399 */
1400 sc->sc_tx_fill_thresh = 64 / 32;
1401
1402 /*
1403 * Start at a drain threshold of 512 bytes. We will
1404 * increase it if a DMA underrun occurs.
1405 *
1406 * XXX The minimum value of this variable should be
1407 * tuned. We may be able to improve performance
1408 * by starting with a lower value. That, however,
1409 * may trash the first few outgoing packets if the
1410 * PCI bus is saturated.
1411 */
1412 if (sc->sc_gigabit)
1413 sc->sc_tx_drain_thresh = 6400 / 32; /* from FreeBSD nge(4) */
1414 else
1415 sc->sc_tx_drain_thresh = 1504 / 32;
1416
1417 /*
1418 * Initialize the Rx FIFO drain threshold.
1419 *
1420 * This is in units of 8 bytes.
1421 *
1422 * We should never set this value lower than 2; 14 bytes are
1423 * required to filter the packet.
1424 */
1425 sc->sc_rx_drain_thresh = 128 / 8;
1426
1427 #ifdef SIP_EVENT_COUNTERS
1428 /*
1429 * Attach event counters.
1430 */
1431 evcnt_attach_dynamic(&sc->sc_ev_txdstall, EVCNT_TYPE_MISC,
1432 NULL, device_xname(sc->sc_dev), "txdstall");
1433 evcnt_attach_dynamic(&sc->sc_ev_txforceintr, EVCNT_TYPE_INTR,
1434 NULL, device_xname(sc->sc_dev), "txforceintr");
1435 evcnt_attach_dynamic(&sc->sc_ev_txdintr, EVCNT_TYPE_INTR,
1436 NULL, device_xname(sc->sc_dev), "txdintr");
1437 evcnt_attach_dynamic(&sc->sc_ev_txiintr, EVCNT_TYPE_INTR,
1438 NULL, device_xname(sc->sc_dev), "txiintr");
1439 evcnt_attach_dynamic(&sc->sc_ev_rxintr, EVCNT_TYPE_INTR,
1440 NULL, device_xname(sc->sc_dev), "rxintr");
1441 evcnt_attach_dynamic(&sc->sc_ev_hiberr, EVCNT_TYPE_INTR,
1442 NULL, device_xname(sc->sc_dev), "hiberr");
1443 if (!sc->sc_gigabit) {
1444 evcnt_attach_dynamic(&sc->sc_ev_rxpause, EVCNT_TYPE_INTR,
1445 NULL, device_xname(sc->sc_dev), "rxpause");
1446 } else {
1447 evcnt_attach_dynamic(&sc->sc_ev_rxpause, EVCNT_TYPE_MISC,
1448 NULL, device_xname(sc->sc_dev), "rxpause");
1449 evcnt_attach_dynamic(&sc->sc_ev_txpause, EVCNT_TYPE_MISC,
1450 NULL, device_xname(sc->sc_dev), "txpause");
1451 evcnt_attach_dynamic(&sc->sc_ev_rxipsum, EVCNT_TYPE_MISC,
1452 NULL, device_xname(sc->sc_dev), "rxipsum");
1453 evcnt_attach_dynamic(&sc->sc_ev_rxtcpsum, EVCNT_TYPE_MISC,
1454 NULL, device_xname(sc->sc_dev), "rxtcpsum");
1455 evcnt_attach_dynamic(&sc->sc_ev_rxudpsum, EVCNT_TYPE_MISC,
1456 NULL, device_xname(sc->sc_dev), "rxudpsum");
1457 evcnt_attach_dynamic(&sc->sc_ev_txipsum, EVCNT_TYPE_MISC,
1458 NULL, device_xname(sc->sc_dev), "txipsum");
1459 evcnt_attach_dynamic(&sc->sc_ev_txtcpsum, EVCNT_TYPE_MISC,
1460 NULL, device_xname(sc->sc_dev), "txtcpsum");
1461 evcnt_attach_dynamic(&sc->sc_ev_txudpsum, EVCNT_TYPE_MISC,
1462 NULL, device_xname(sc->sc_dev), "txudpsum");
1463 }
1464 #endif /* SIP_EVENT_COUNTERS */
1465
1466 if (pmf_device_register(self, sipcom_suspend, sipcom_resume))
1467 pmf_class_network_register(self, ifp);
1468 else
1469 aprint_error_dev(self, "couldn't establish power handler\n");
1470 }
1471
1472 static inline void
sipcom_set_extsts(struct sip_softc * sc,int lasttx,struct mbuf * m0,uint64_t capenable)1473 sipcom_set_extsts(struct sip_softc *sc, int lasttx, struct mbuf *m0,
1474 uint64_t capenable)
1475 {
1476 uint32_t extsts = 0;
1477 #ifdef DEBUG
1478 struct ifnet *ifp = &sc->sc_ethercom.ec_if;
1479 #endif
1480 /*
1481 * If VLANs are enabled and the packet has a VLAN tag, set
1482 * up the descriptor to encapsulate the packet for us.
1483 *
1484 * This apparently has to be on the last descriptor of
1485 * the packet.
1486 */
1487
1488 /*
1489 * Byte swapping is tricky. We need to provide the tag
1490 * in a network byte order. On a big-endian machine,
1491 * the byteorder is correct, but we need to swap it
1492 * anyway, because this will be undone by the outside
1493 * htole32(). That's why there must be an
1494 * unconditional swap instead of htons() inside.
1495 */
1496 if (vlan_has_tag(m0)) {
1497 sc->sc_txdescs[lasttx].sipd_words[sc->sc_extsts_idx] |=
1498 htole32(EXTSTS_VPKT |
1499 (bswap16(vlan_get_tag(m0)) &
1500 EXTSTS_VTCI));
1501 }
1502
1503 /*
1504 * If the upper-layer has requested IPv4/TCPv4/UDPv4
1505 * checksumming, set up the descriptor to do this work
1506 * for us.
1507 *
1508 * This apparently has to be on the first descriptor of
1509 * the packet.
1510 *
1511 * Byte-swap constants so the compiler can optimize.
1512 */
1513 if (m0->m_pkthdr.csum_flags & M_CSUM_IPv4) {
1514 KDASSERT(ifp->if_capenable & IFCAP_CSUM_IPv4_Tx);
1515 SIP_EVCNT_INCR(&sc->sc_ev_txipsum);
1516 extsts |= htole32(EXTSTS_IPPKT);
1517 }
1518 if (m0->m_pkthdr.csum_flags & M_CSUM_TCPv4) {
1519 KDASSERT(ifp->if_capenable & IFCAP_CSUM_TCPv4_Tx);
1520 SIP_EVCNT_INCR(&sc->sc_ev_txtcpsum);
1521 extsts |= htole32(EXTSTS_TCPPKT);
1522 } else if (m0->m_pkthdr.csum_flags & M_CSUM_UDPv4) {
1523 KDASSERT(ifp->if_capenable & IFCAP_CSUM_UDPv4_Tx);
1524 SIP_EVCNT_INCR(&sc->sc_ev_txudpsum);
1525 extsts |= htole32(EXTSTS_UDPPKT);
1526 }
1527 sc->sc_txdescs[sc->sc_txnext].sipd_words[sc->sc_extsts_idx] |= extsts;
1528 }
1529
1530 /*
1531 * sip_start: [ifnet interface function]
1532 *
1533 * Start packet transmission on the interface.
1534 */
1535 static void
sipcom_start(struct ifnet * ifp)1536 sipcom_start(struct ifnet *ifp)
1537 {
1538 struct sip_softc *sc = ifp->if_softc;
1539 struct mbuf *m0;
1540 struct mbuf *m;
1541 struct sip_txsoft *txs;
1542 bus_dmamap_t dmamap;
1543 int error, nexttx, lasttx, seg;
1544 int ofree = sc->sc_txfree;
1545 uint32_t cmdsts;
1546 #if 0
1547 int firsttx = sc->sc_txnext;
1548 #endif
1549
1550 /*
1551 * If we've been told to pause, don't transmit any more packets.
1552 */
1553 if (!sc->sc_gigabit && sc->sc_paused)
1554 return;
1555
1556 if ((ifp->if_flags & IFF_RUNNING) != IFF_RUNNING)
1557 return;
1558
1559 /*
1560 * Loop through the send queue, setting up transmit descriptors
1561 * until we drain the queue, or use up all available transmit
1562 * descriptors.
1563 */
1564 while ((txs = SIMPLEQ_FIRST(&sc->sc_txfreeq)) != NULL) {
1565 /*
1566 * Grab a packet off the queue.
1567 */
1568 IFQ_POLL(&ifp->if_snd, m0);
1569 if (m0 == NULL)
1570 break;
1571 m = NULL;
1572
1573 dmamap = txs->txs_dmamap;
1574
1575 /*
1576 * Load the DMA map. If this fails, the packet either
1577 * didn't fit in the alloted number of segments, or we
1578 * were short on resources.
1579 */
1580 error = bus_dmamap_load_mbuf(sc->sc_dmat, dmamap, m0,
1581 BUS_DMA_WRITE | BUS_DMA_NOWAIT);
1582 /* In the non-gigabit case, we'll copy and try again. */
1583 if (error != 0 && !sc->sc_gigabit) {
1584 MGETHDR(m, M_DONTWAIT, MT_DATA);
1585 if (m == NULL) {
1586 printf("%s: unable to allocate Tx mbuf\n",
1587 device_xname(sc->sc_dev));
1588 break;
1589 }
1590 MCLAIM(m, &sc->sc_ethercom.ec_tx_mowner);
1591 if (m0->m_pkthdr.len > MHLEN) {
1592 MCLGET(m, M_DONTWAIT);
1593 if ((m->m_flags & M_EXT) == 0) {
1594 printf("%s: unable to allocate Tx "
1595 "cluster\n",
1596 device_xname(sc->sc_dev));
1597 m_freem(m);
1598 break;
1599 }
1600 }
1601 m_copydata(m0, 0, m0->m_pkthdr.len, mtod(m, void *));
1602 m->m_pkthdr.len = m->m_len = m0->m_pkthdr.len;
1603 error = bus_dmamap_load_mbuf(sc->sc_dmat, dmamap,
1604 m, BUS_DMA_WRITE | BUS_DMA_NOWAIT);
1605 if (error) {
1606 printf("%s: unable to load Tx buffer, error = "
1607 "%d\n", device_xname(sc->sc_dev), error);
1608 break;
1609 }
1610 } else if (error == EFBIG) {
1611 /*
1612 * For the too-many-segments case, we simply
1613 * report an error and drop the packet,
1614 * since we can't sanely copy a jumbo packet
1615 * to a single buffer.
1616 */
1617 printf("%s: Tx packet consumes too many DMA segments, "
1618 "dropping...\n", device_xname(sc->sc_dev));
1619 IFQ_DEQUEUE(&ifp->if_snd, m0);
1620 m_freem(m0);
1621 continue;
1622 } else if (error != 0) {
1623 /*
1624 * Short on resources, just stop for now.
1625 */
1626 break;
1627 }
1628
1629 /*
1630 * Ensure we have enough descriptors free to describe
1631 * the packet. Note, we always reserve one descriptor
1632 * at the end of the ring as a termination point, to
1633 * prevent wrap-around.
1634 */
1635 if (dmamap->dm_nsegs > (sc->sc_txfree - 1)) {
1636 /*
1637 * Not enough free descriptors to transmit this
1638 * packet.
1639 */
1640 bus_dmamap_unload(sc->sc_dmat, dmamap);
1641 if (m != NULL)
1642 m_freem(m);
1643 SIP_EVCNT_INCR(&sc->sc_ev_txdstall);
1644 break;
1645 }
1646
1647 IFQ_DEQUEUE(&ifp->if_snd, m0);
1648 if (m != NULL) {
1649 m_freem(m0);
1650 m0 = m;
1651 }
1652
1653 /*
1654 * WE ARE NOW COMMITTED TO TRANSMITTING THE PACKET.
1655 */
1656
1657 /* Sync the DMA map. */
1658 bus_dmamap_sync(sc->sc_dmat, dmamap, 0, dmamap->dm_mapsize,
1659 BUS_DMASYNC_PREWRITE);
1660
1661 /*
1662 * Initialize the transmit descriptors.
1663 */
1664 for (nexttx = lasttx = sc->sc_txnext, seg = 0;
1665 seg < dmamap->dm_nsegs;
1666 seg++, nexttx = sip_nexttx(sc, nexttx)) {
1667 /*
1668 * If this is the first descriptor we're
1669 * enqueueing, don't set the OWN bit just
1670 * yet. That could cause a race condition.
1671 * We'll do it below.
1672 */
1673
1674 cmdsts = dmamap->dm_segs[seg].ds_len;
1675 if (nexttx != sc->sc_txnext)
1676 cmdsts |= CMDSTS_OWN;
1677 if (seg < dmamap->dm_nsegs - 1)
1678 cmdsts |= CMDSTS_MORE;
1679 sip_init_txdesc(sc, nexttx,
1680 dmamap->dm_segs[seg].ds_addr, cmdsts);
1681 lasttx = nexttx;
1682 }
1683
1684 /*
1685 * If we're in the interrupt delay window, delay the
1686 * interrupt.
1687 */
1688 if (++sc->sc_txwin >= (SIP_TXQUEUELEN * 2 / 3)) {
1689 SIP_EVCNT_INCR(&sc->sc_ev_txforceintr);
1690 sc->sc_txdescs[lasttx].sipd_words[sc->sc_cmdsts_idx] |=
1691 htole32(CMDSTS_INTR);
1692 sc->sc_txwin = 0;
1693 }
1694
1695 if (sc->sc_gigabit)
1696 sipcom_set_extsts(sc, lasttx, m0, ifp->if_capenable);
1697
1698 /* Sync the descriptors we're using. */
1699 sip_cdtxsync(sc, sc->sc_txnext, dmamap->dm_nsegs,
1700 BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE);
1701
1702 /*
1703 * The entire packet is set up. Give the first descriptor
1704 * to the chip now.
1705 */
1706 sc->sc_txdescs[sc->sc_txnext].sipd_words[sc->sc_cmdsts_idx] |=
1707 htole32(CMDSTS_OWN);
1708 sip_cdtxsync(sc, sc->sc_txnext, 1,
1709 BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE);
1710
1711 /*
1712 * Store a pointer to the packet so we can free it later,
1713 * and remember what txdirty will be once the packet is
1714 * done.
1715 */
1716 txs->txs_mbuf = m0;
1717 txs->txs_firstdesc = sc->sc_txnext;
1718 txs->txs_lastdesc = lasttx;
1719
1720 /* Advance the tx pointer. */
1721 sc->sc_txfree -= dmamap->dm_nsegs;
1722 sc->sc_txnext = nexttx;
1723
1724 SIMPLEQ_REMOVE_HEAD(&sc->sc_txfreeq, txs_q);
1725 SIMPLEQ_INSERT_TAIL(&sc->sc_txdirtyq, txs, txs_q);
1726
1727 /* Pass the packet to any BPF listeners. */
1728 bpf_mtap(ifp, m0, BPF_D_OUT);
1729 }
1730
1731 if (sc->sc_txfree != ofree) {
1732 /*
1733 * Start the transmit process. Note, the manual says
1734 * that if there are no pending transmissions in the
1735 * chip's internal queue (indicated by TXE being clear),
1736 * then the driver software must set the TXDP to the
1737 * first descriptor to be transmitted. However, if we
1738 * do this, it causes serious performance degradation on
1739 * the DP83820 under load, not setting TXDP doesn't seem
1740 * to adversely affect the SiS 900 or DP83815.
1741 *
1742 * Well, I guess it wouldn't be the first time a manual
1743 * has lied -- and they could be speaking of the NULL-
1744 * terminated descriptor list case, rather than OWN-
1745 * terminated rings.
1746 */
1747 #if 0
1748 if ((bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_CR) &
1749 CR_TXE) == 0) {
1750 sip_set_txdp(sc, SIP_CDTXADDR(sc, firsttx));
1751 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_CR, CR_TXE);
1752 }
1753 #else
1754 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_CR, CR_TXE);
1755 #endif
1756
1757 /* Set a watchdog timer in case the chip flakes out. */
1758 /* Gigabit autonegotiation takes 5 seconds. */
1759 ifp->if_timer = (sc->sc_gigabit) ? 10 : 5;
1760 }
1761 }
1762
1763 /*
1764 * sip_watchdog: [ifnet interface function]
1765 *
1766 * Watchdog timer handler.
1767 */
1768 static void
sipcom_watchdog(struct ifnet * ifp)1769 sipcom_watchdog(struct ifnet *ifp)
1770 {
1771 struct sip_softc *sc = ifp->if_softc;
1772
1773 /*
1774 * The chip seems to ignore the CMDSTS_INTR bit sometimes!
1775 * If we get a timeout, try and sweep up transmit descriptors.
1776 * If we manage to sweep them all up, ignore the lack of
1777 * interrupt.
1778 */
1779 sipcom_txintr(sc);
1780
1781 if (sc->sc_txfree != sc->sc_ntxdesc) {
1782 printf("%s: device timeout\n", device_xname(sc->sc_dev));
1783 if_statinc(ifp, if_oerrors);
1784
1785 /* Reset the interface. */
1786 (void) sipcom_init(ifp);
1787 } else if (ifp->if_flags & IFF_DEBUG)
1788 printf("%s: recovered from device timeout\n",
1789 device_xname(sc->sc_dev));
1790
1791 /* Try to get more packets going. */
1792 sipcom_start(ifp);
1793 }
1794
1795 /* If the interface is up and running, only modify the receive
1796 * filter when setting promiscuous or debug mode. Otherwise fall
1797 * through to ether_ioctl, which will reset the chip.
1798 */
1799 static int
sip_ifflags_cb(struct ethercom * ec)1800 sip_ifflags_cb(struct ethercom *ec)
1801 {
1802 #define COMPARE_EC(sc) (((sc)->sc_prev.ec_capenable \
1803 == (sc)->sc_ethercom.ec_capenable) \
1804 && ((sc)->sc_prev.is_vlan == \
1805 VLAN_ATTACHED(&(sc)->sc_ethercom) ))
1806 #define COMPARE_IC(sc, ifp) ((sc)->sc_prev.if_capenable == (ifp)->if_capenable)
1807 struct ifnet *ifp = &ec->ec_if;
1808 struct sip_softc *sc = ifp->if_softc;
1809 u_short change = ifp->if_flags ^ sc->sc_if_flags;
1810
1811 if ((change & ~(IFF_CANTCHANGE | IFF_DEBUG)) != 0 || !COMPARE_EC(sc) ||
1812 !COMPARE_IC(sc, ifp))
1813 return ENETRESET;
1814 /* Set up the receive filter. */
1815 (*sc->sc_model->sip_variant->sipv_set_filter)(sc);
1816 return 0;
1817 }
1818
1819 /*
1820 * sip_ioctl: [ifnet interface function]
1821 *
1822 * Handle control requests from the operator.
1823 */
1824 static int
sipcom_ioctl(struct ifnet * ifp,u_long cmd,void * data)1825 sipcom_ioctl(struct ifnet *ifp, u_long cmd, void *data)
1826 {
1827 struct sip_softc *sc = ifp->if_softc;
1828 struct ifreq *ifr = (struct ifreq *)data;
1829 int s, error;
1830
1831 s = splnet();
1832
1833 switch (cmd) {
1834 case SIOCSIFMEDIA:
1835 /* Flow control requires full-duplex mode. */
1836 if (IFM_SUBTYPE(ifr->ifr_media) == IFM_AUTO ||
1837 (ifr->ifr_media & IFM_FDX) == 0)
1838 ifr->ifr_media &= ~IFM_ETH_FMASK;
1839
1840 /* XXX */
1841 if (SIP_CHIP_MODEL(sc, PCI_VENDOR_NS, PCI_PRODUCT_NS_DP83815))
1842 ifr->ifr_media &= ~IFM_ETH_FMASK;
1843 if (IFM_SUBTYPE(ifr->ifr_media) != IFM_AUTO) {
1844 if (sc->sc_gigabit &&
1845 (ifr->ifr_media & IFM_ETH_FMASK) == IFM_FLOW) {
1846 /* We can do both TXPAUSE and RXPAUSE. */
1847 ifr->ifr_media |=
1848 IFM_ETH_TXPAUSE | IFM_ETH_RXPAUSE;
1849 } else if (ifr->ifr_media & IFM_FLOW) {
1850 /*
1851 * Both TXPAUSE and RXPAUSE must be set.
1852 * (SiS900 and DP83815 don't have PAUSE_ASYM
1853 * feature.)
1854 *
1855 * XXX Can SiS900 and DP83815 send PAUSE?
1856 */
1857 ifr->ifr_media |=
1858 IFM_ETH_TXPAUSE | IFM_ETH_RXPAUSE;
1859 }
1860 sc->sc_flowflags = ifr->ifr_media & IFM_ETH_FMASK;
1861 }
1862 /*FALLTHROUGH*/
1863 default:
1864 if ((error = ether_ioctl(ifp, cmd, data)) != ENETRESET)
1865 break;
1866
1867 error = 0;
1868
1869 if (cmd == SIOCSIFCAP)
1870 error = if_init(ifp);
1871 else if (cmd != SIOCADDMULTI && cmd != SIOCDELMULTI)
1872 ;
1873 else if (ifp->if_flags & IFF_RUNNING) {
1874 /*
1875 * Multicast list has changed; set the hardware filter
1876 * accordingly.
1877 */
1878 (*sc->sc_model->sip_variant->sipv_set_filter)(sc);
1879 }
1880 break;
1881 }
1882
1883 /* Try to get more packets going. */
1884 sipcom_start(ifp);
1885
1886 sc->sc_if_flags = ifp->if_flags;
1887 splx(s);
1888 return error;
1889 }
1890
1891 /*
1892 * sip_intr:
1893 *
1894 * Interrupt service routine.
1895 */
1896 static int
sipcom_intr(void * arg)1897 sipcom_intr(void *arg)
1898 {
1899 struct sip_softc *sc = arg;
1900 struct ifnet *ifp = &sc->sc_ethercom.ec_if;
1901 uint32_t isr;
1902 int handled = 0;
1903
1904 if (!device_activation(sc->sc_dev, DEVACT_LEVEL_DRIVER))
1905 return 0;
1906
1907 /* Disable interrupts. */
1908 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_IER, 0);
1909
1910 for (;;) {
1911 /* Reading clears interrupt. */
1912 isr = bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_ISR);
1913 if ((isr & sc->sc_imr) == 0)
1914 break;
1915
1916 rnd_add_uint32(&sc->rnd_source, isr);
1917
1918 handled = 1;
1919
1920 if ((ifp->if_flags & IFF_RUNNING) == 0)
1921 break;
1922
1923 if (isr & (ISR_RXORN | ISR_RXIDLE | ISR_RXDESC)) {
1924 SIP_EVCNT_INCR(&sc->sc_ev_rxintr);
1925
1926 /* Grab any new packets. */
1927 (*sc->sc_rxintr)(sc);
1928
1929 if (isr & ISR_RXORN) {
1930 printf("%s: receive FIFO overrun\n",
1931 device_xname(sc->sc_dev));
1932
1933 /* XXX adjust rx_drain_thresh? */
1934 }
1935
1936 if (isr & ISR_RXIDLE) {
1937 printf("%s: receive ring overrun\n",
1938 device_xname(sc->sc_dev));
1939
1940 /* Get the receive process going again. */
1941 sip_set_rxdp(sc,
1942 SIP_CDRXADDR(sc, sc->sc_rxptr));
1943 bus_space_write_4(sc->sc_st, sc->sc_sh,
1944 SIP_CR, CR_RXE);
1945 }
1946 }
1947
1948 if (isr & (ISR_TXURN | ISR_TXDESC | ISR_TXIDLE)) {
1949 #ifdef SIP_EVENT_COUNTERS
1950 if (isr & ISR_TXDESC)
1951 SIP_EVCNT_INCR(&sc->sc_ev_txdintr);
1952 else if (isr & ISR_TXIDLE)
1953 SIP_EVCNT_INCR(&sc->sc_ev_txiintr);
1954 #endif
1955
1956 /* Sweep up transmit descriptors. */
1957 sipcom_txintr(sc);
1958
1959 if (isr & ISR_TXURN) {
1960 uint32_t thresh;
1961 int txfifo_size = (sc->sc_gigabit)
1962 ? DP83820_SIP_TXFIFO_SIZE
1963 : OTHER_SIP_TXFIFO_SIZE;
1964
1965 printf("%s: transmit FIFO underrun",
1966 device_xname(sc->sc_dev));
1967 thresh = sc->sc_tx_drain_thresh + 1;
1968 if (thresh <= __SHIFTOUT_MASK(sc->sc_bits.b_txcfg_drth_mask)
1969 && (thresh * 32) <= (txfifo_size -
1970 (sc->sc_tx_fill_thresh * 32))) {
1971 printf("; increasing Tx drain "
1972 "threshold to %u bytes\n",
1973 thresh * 32);
1974 sc->sc_tx_drain_thresh = thresh;
1975 (void) sipcom_init(ifp);
1976 } else {
1977 (void) sipcom_init(ifp);
1978 printf("\n");
1979 }
1980 }
1981 }
1982
1983 if (sc->sc_imr & (ISR_PAUSE_END | ISR_PAUSE_ST)) {
1984 if (isr & ISR_PAUSE_ST) {
1985 sc->sc_paused = 1;
1986 SIP_EVCNT_INCR(&sc->sc_ev_rxpause);
1987 }
1988 if (isr & ISR_PAUSE_END) {
1989 sc->sc_paused = 0;
1990 }
1991 }
1992
1993 if (isr & ISR_HIBERR) {
1994 int want_init = 0;
1995
1996 SIP_EVCNT_INCR(&sc->sc_ev_hiberr);
1997
1998 #define PRINTERR(bit, str) \
1999 do { \
2000 if ((isr & (bit)) != 0) { \
2001 if ((ifp->if_flags & IFF_DEBUG) != 0) \
2002 printf("%s: %s\n", \
2003 device_xname(sc->sc_dev), str); \
2004 want_init = 1; \
2005 } \
2006 } while (/*CONSTCOND*/0)
2007
2008 PRINTERR(sc->sc_bits.b_isr_dperr, "parity error");
2009 PRINTERR(sc->sc_bits.b_isr_sserr, "system error");
2010 PRINTERR(sc->sc_bits.b_isr_rmabt, "master abort");
2011 PRINTERR(sc->sc_bits.b_isr_rtabt, "target abort");
2012 PRINTERR(ISR_RXSOVR, "receive status FIFO overrun");
2013 /*
2014 * Ignore:
2015 * Tx reset complete
2016 * Rx reset complete
2017 */
2018 if (want_init)
2019 (void) sipcom_init(ifp);
2020 #undef PRINTERR
2021 }
2022 }
2023
2024 /* Re-enable interrupts. */
2025 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_IER, IER_IE);
2026
2027 /* Try to get more packets going. */
2028 if_schedule_deferred_start(ifp);
2029
2030 return handled;
2031 }
2032
2033 /*
2034 * sip_txintr:
2035 *
2036 * Helper; handle transmit interrupts.
2037 */
2038 static void
sipcom_txintr(struct sip_softc * sc)2039 sipcom_txintr(struct sip_softc *sc)
2040 {
2041 struct ifnet *ifp = &sc->sc_ethercom.ec_if;
2042 struct sip_txsoft *txs;
2043 uint32_t cmdsts;
2044
2045 /*
2046 * Go through our Tx list and free mbufs for those
2047 * frames which have been transmitted.
2048 */
2049 while ((txs = SIMPLEQ_FIRST(&sc->sc_txdirtyq)) != NULL) {
2050 sip_cdtxsync(sc, txs->txs_firstdesc, txs->txs_dmamap->dm_nsegs,
2051 BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE);
2052
2053 cmdsts = le32toh(sc->sc_txdescs[
2054 txs->txs_lastdesc].sipd_words[sc->sc_cmdsts_idx]);
2055 if (cmdsts & CMDSTS_OWN)
2056 break;
2057
2058 SIMPLEQ_REMOVE_HEAD(&sc->sc_txdirtyq, txs_q);
2059
2060 sc->sc_txfree += txs->txs_dmamap->dm_nsegs;
2061
2062 bus_dmamap_sync(sc->sc_dmat, txs->txs_dmamap,
2063 0, txs->txs_dmamap->dm_mapsize, BUS_DMASYNC_POSTWRITE);
2064 bus_dmamap_unload(sc->sc_dmat, txs->txs_dmamap);
2065 m_freem(txs->txs_mbuf);
2066 txs->txs_mbuf = NULL;
2067
2068 SIMPLEQ_INSERT_TAIL(&sc->sc_txfreeq, txs, txs_q);
2069
2070 /* Check for errors and collisions. */
2071 net_stat_ref_t nsr = IF_STAT_GETREF(ifp);
2072 if (cmdsts & (CMDSTS_Tx_TXA | CMDSTS_Tx_TFU | CMDSTS_Tx_ED |
2073 CMDSTS_Tx_EC)) {
2074 if_statinc_ref(nsr, if_oerrors);
2075 if (cmdsts & CMDSTS_Tx_EC)
2076 if_statadd_ref(nsr, if_collisions, 16);
2077 if (ifp->if_flags & IFF_DEBUG) {
2078 if (cmdsts & CMDSTS_Tx_ED)
2079 printf("%s: excessive deferral\n",
2080 device_xname(sc->sc_dev));
2081 if (cmdsts & CMDSTS_Tx_EC)
2082 printf("%s: excessive collisions\n",
2083 device_xname(sc->sc_dev));
2084 }
2085 } else {
2086 /* Packet was transmitted successfully. */
2087 if_statinc_ref(nsr, if_opackets);
2088 if (CMDSTS_COLLISIONS(cmdsts))
2089 if_statadd_ref(nsr, if_collisions,
2090 CMDSTS_COLLISIONS(cmdsts));
2091 }
2092 IF_STAT_PUTREF(ifp);
2093 }
2094
2095 /*
2096 * If there are no more pending transmissions, cancel the watchdog
2097 * timer.
2098 */
2099 if (txs == NULL) {
2100 ifp->if_timer = 0;
2101 sc->sc_txwin = 0;
2102 }
2103 }
2104
2105 /*
2106 * gsip_rxintr:
2107 *
2108 * Helper; handle receive interrupts on gigabit parts.
2109 */
2110 static void
gsip_rxintr(struct sip_softc * sc)2111 gsip_rxintr(struct sip_softc *sc)
2112 {
2113 struct ifnet *ifp = &sc->sc_ethercom.ec_if;
2114 struct sip_rxsoft *rxs;
2115 struct mbuf *m;
2116 uint32_t cmdsts, extsts;
2117 int i, len;
2118
2119 for (i = sc->sc_rxptr;; i = sip_nextrx(sc, i)) {
2120 rxs = &sc->sc_rxsoft[i];
2121
2122 sip_cdrxsync(sc, i,
2123 BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE);
2124
2125 cmdsts =
2126 le32toh(sc->sc_rxdescs[i].sipd_words[sc->sc_cmdsts_idx]);
2127
2128 /*
2129 * NOTE: OWN is set if owned by _consumer_. We're the
2130 * consumer of the receive ring, so if the bit is clear,
2131 * we have processed all of the packets.
2132 */
2133 if ((cmdsts & CMDSTS_OWN) == 0) {
2134 /*
2135 * We have processed all of the receive buffers.
2136 */
2137 break;
2138 }
2139
2140 sip_cdrxsync(sc, i, BUS_DMASYNC_POSTREAD);
2141
2142 extsts =
2143 le32toh(sc->sc_rxdescs[i].sipd_words[sc->sc_extsts_idx]);
2144 len = CMDSTS_SIZE(sc, cmdsts);
2145
2146 if (__predict_false(sc->sc_rxdiscard)) {
2147 sip_init_rxdesc(sc, i);
2148 if ((cmdsts & CMDSTS_MORE) == 0) {
2149 /* Reset our state. */
2150 sc->sc_rxdiscard = 0;
2151 }
2152 continue;
2153 }
2154
2155 bus_dmamap_sync(sc->sc_dmat, rxs->rxs_dmamap, 0,
2156 rxs->rxs_dmamap->dm_mapsize, BUS_DMASYNC_POSTREAD);
2157
2158 m = rxs->rxs_mbuf;
2159
2160 /*
2161 * Add a new receive buffer to the ring.
2162 */
2163 if (sipcom_add_rxbuf(sc, i) != 0) {
2164 /*
2165 * Failed, throw away what we've done so
2166 * far, and discard the rest of the packet.
2167 */
2168 if_statinc(ifp, if_ierrors);
2169 bus_dmamap_sync(sc->sc_dmat, rxs->rxs_dmamap, 0,
2170 rxs->rxs_dmamap->dm_mapsize, BUS_DMASYNC_PREREAD);
2171 sip_init_rxdesc(sc, i);
2172 if (cmdsts & CMDSTS_MORE)
2173 sc->sc_rxdiscard = 1;
2174 if (sc->sc_rxhead != NULL)
2175 m_freem(sc->sc_rxhead);
2176 sip_rxchain_reset(sc);
2177 continue;
2178 }
2179
2180 sip_rxchain_link(sc, m);
2181
2182 m->m_len = len;
2183
2184 /*
2185 * If this is not the end of the packet, keep
2186 * looking.
2187 */
2188 if (cmdsts & CMDSTS_MORE) {
2189 sc->sc_rxlen += len;
2190 continue;
2191 }
2192
2193 /*
2194 * Okay, we have the entire packet now. The chip includes
2195 * the FCS, so we need to trim it.
2196 */
2197 m->m_len -= ETHER_CRC_LEN;
2198
2199 *sc->sc_rxtailp = NULL;
2200 len = m->m_len + sc->sc_rxlen;
2201 m = sc->sc_rxhead;
2202
2203 sip_rxchain_reset(sc);
2204
2205 /* If an error occurred, update stats and drop the packet. */
2206 if (cmdsts & (CMDSTS_Rx_RXA | CMDSTS_Rx_LONG | CMDSTS_Rx_RUNT |
2207 CMDSTS_Rx_ISE | CMDSTS_Rx_CRCE | CMDSTS_Rx_FAE)) {
2208 if_statinc(ifp, if_ierrors);
2209 if ((cmdsts & CMDSTS_Rx_RXA) != 0 &&
2210 (cmdsts & CMDSTS_Rx_RXO) == 0) {
2211 /* Receive overrun handled elsewhere. */
2212 printf("%s: receive descriptor error\n",
2213 device_xname(sc->sc_dev));
2214 }
2215 #define PRINTERR(bit, str) \
2216 if ((ifp->if_flags & IFF_DEBUG) != 0 && \
2217 (cmdsts & (bit)) != 0) \
2218 printf("%s: %s\n", device_xname(sc->sc_dev), str)
2219 PRINTERR(CMDSTS_Rx_LONG, "Too long packet");
2220 PRINTERR(CMDSTS_Rx_RUNT, "runt packet");
2221 PRINTERR(CMDSTS_Rx_ISE, "invalid symbol error");
2222 PRINTERR(CMDSTS_Rx_CRCE, "CRC error");
2223 PRINTERR(CMDSTS_Rx_FAE, "frame alignment error");
2224 #undef PRINTERR
2225 m_freem(m);
2226 continue;
2227 }
2228
2229 /*
2230 * If the packet is small enough to fit in a
2231 * single header mbuf, allocate one and copy
2232 * the data into it. This greatly reduces
2233 * memory consumption when we receive lots
2234 * of small packets.
2235 */
2236 if (gsip_copy_small != 0 && len <= (MHLEN - 2)) {
2237 struct mbuf *nm;
2238 MGETHDR(nm, M_DONTWAIT, MT_DATA);
2239 if (nm == NULL) {
2240 if_statinc(ifp, if_ierrors);
2241 m_freem(m);
2242 continue;
2243 }
2244 MCLAIM(m, &sc->sc_ethercom.ec_rx_mowner);
2245 nm->m_data += 2;
2246 nm->m_pkthdr.len = nm->m_len = len;
2247 m_copydata(m, 0, len, mtod(nm, void *));
2248 m_freem(m);
2249 m = nm;
2250 }
2251 #ifndef __NO_STRICT_ALIGNMENT
2252 else {
2253 /*
2254 * The DP83820's receive buffers must be 4-byte
2255 * aligned. But this means that the data after
2256 * the Ethernet header is misaligned. To compensate,
2257 * we have artificially shortened the buffer size
2258 * in the descriptor, and we do an overlapping copy
2259 * of the data two bytes further in (in the first
2260 * buffer of the chain only).
2261 */
2262 memmove(mtod(m, char *) + 2, mtod(m, void *),
2263 m->m_len);
2264 m->m_data += 2;
2265 }
2266 #endif /* ! __NO_STRICT_ALIGNMENT */
2267
2268 /*
2269 * If VLANs are enabled, VLAN packets have been unwrapped
2270 * for us. Associate the tag with the packet.
2271 */
2272
2273 /*
2274 * Again, byte swapping is tricky. Hardware provided
2275 * the tag in the network byte order, but extsts was
2276 * passed through le32toh() in the meantime. On a
2277 * big-endian machine, we need to swap it again. On a
2278 * little-endian machine, we need to convert from the
2279 * network to host byte order. This means that we must
2280 * swap it in any case, so unconditional swap instead
2281 * of htons() is used.
2282 */
2283 if ((extsts & EXTSTS_VPKT) != 0) {
2284 vlan_set_tag(m, bswap16(extsts & EXTSTS_VTCI));
2285 }
2286
2287 /*
2288 * Set the incoming checksum information for the
2289 * packet.
2290 */
2291 if ((extsts & EXTSTS_IPPKT) != 0) {
2292 SIP_EVCNT_INCR(&sc->sc_ev_rxipsum);
2293 m->m_pkthdr.csum_flags |= M_CSUM_IPv4;
2294 if (extsts & EXTSTS_Rx_IPERR)
2295 m->m_pkthdr.csum_flags |= M_CSUM_IPv4_BAD;
2296 if (extsts & EXTSTS_TCPPKT) {
2297 SIP_EVCNT_INCR(&sc->sc_ev_rxtcpsum);
2298 m->m_pkthdr.csum_flags |= M_CSUM_TCPv4;
2299 if (extsts & EXTSTS_Rx_TCPERR)
2300 m->m_pkthdr.csum_flags |=
2301 M_CSUM_TCP_UDP_BAD;
2302 } else if (extsts & EXTSTS_UDPPKT) {
2303 SIP_EVCNT_INCR(&sc->sc_ev_rxudpsum);
2304 m->m_pkthdr.csum_flags |= M_CSUM_UDPv4;
2305 if (extsts & EXTSTS_Rx_UDPERR)
2306 m->m_pkthdr.csum_flags |=
2307 M_CSUM_TCP_UDP_BAD;
2308 }
2309 }
2310
2311 m_set_rcvif(m, ifp);
2312 m->m_pkthdr.len = len;
2313
2314 /* Pass it on. */
2315 if_percpuq_enqueue(ifp->if_percpuq, m);
2316 }
2317
2318 /* Update the receive pointer. */
2319 sc->sc_rxptr = i;
2320 }
2321
2322 /*
2323 * sip_rxintr:
2324 *
2325 * Helper; handle receive interrupts on 10/100 parts.
2326 */
2327 static void
sip_rxintr(struct sip_softc * sc)2328 sip_rxintr(struct sip_softc *sc)
2329 {
2330 struct ifnet *ifp = &sc->sc_ethercom.ec_if;
2331 struct sip_rxsoft *rxs;
2332 struct mbuf *m;
2333 uint32_t cmdsts;
2334 int i, len;
2335
2336 for (i = sc->sc_rxptr;; i = sip_nextrx(sc, i)) {
2337 rxs = &sc->sc_rxsoft[i];
2338
2339 sip_cdrxsync(sc, i,
2340 BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE);
2341
2342 cmdsts =
2343 le32toh(sc->sc_rxdescs[i].sipd_words[sc->sc_cmdsts_idx]);
2344
2345 /*
2346 * NOTE: OWN is set if owned by _consumer_. We're the
2347 * consumer of the receive ring, so if the bit is clear,
2348 * we have processed all of the packets.
2349 */
2350 if ((cmdsts & CMDSTS_OWN) == 0) {
2351 /*
2352 * We have processed all of the receive buffers.
2353 */
2354 break;
2355 }
2356
2357 /* If any collisions were seen on the wire, count one. */
2358 if (cmdsts & CMDSTS_Rx_COL)
2359 if_statinc(ifp, if_collisions);
2360
2361 /*
2362 * If an error occurred, update stats, clear the status
2363 * word, and leave the packet buffer in place. It will
2364 * simply be reused the next time the ring comes around.
2365 */
2366 if (cmdsts & (CMDSTS_Rx_RXA | CMDSTS_Rx_LONG | CMDSTS_Rx_RUNT |
2367 CMDSTS_Rx_ISE | CMDSTS_Rx_CRCE | CMDSTS_Rx_FAE)) {
2368 if_statinc(ifp, if_ierrors);
2369 if ((cmdsts & CMDSTS_Rx_RXA) != 0 &&
2370 (cmdsts & CMDSTS_Rx_RXO) == 0) {
2371 /* Receive overrun handled elsewhere. */
2372 printf("%s: receive descriptor error\n",
2373 device_xname(sc->sc_dev));
2374 }
2375 #define PRINTERR(bit, str) \
2376 if ((ifp->if_flags & IFF_DEBUG) != 0 && \
2377 (cmdsts & (bit)) != 0) \
2378 printf("%s: %s\n", device_xname(sc->sc_dev), str)
2379 PRINTERR(CMDSTS_Rx_LONG, "Too long packet");
2380 PRINTERR(CMDSTS_Rx_RUNT, "runt packet");
2381 PRINTERR(CMDSTS_Rx_ISE, "invalid symbol error");
2382 PRINTERR(CMDSTS_Rx_CRCE, "CRC error");
2383 PRINTERR(CMDSTS_Rx_FAE, "frame alignment error");
2384 #undef PRINTERR
2385 sip_init_rxdesc(sc, i);
2386 continue;
2387 }
2388
2389 bus_dmamap_sync(sc->sc_dmat, rxs->rxs_dmamap, 0,
2390 rxs->rxs_dmamap->dm_mapsize, BUS_DMASYNC_POSTREAD);
2391
2392 /*
2393 * No errors; receive the packet. Note, the SiS 900
2394 * includes the CRC with every packet.
2395 */
2396 len = CMDSTS_SIZE(sc, cmdsts) - ETHER_CRC_LEN;
2397
2398 #ifdef __NO_STRICT_ALIGNMENT
2399 /*
2400 * If the packet is small enough to fit in a
2401 * single header mbuf, allocate one and copy
2402 * the data into it. This greatly reduces
2403 * memory consumption when we receive lots
2404 * of small packets.
2405 *
2406 * Otherwise, we add a new buffer to the receive
2407 * chain. If this fails, we drop the packet and
2408 * recycle the old buffer.
2409 */
2410 if (sip_copy_small != 0 && len <= MHLEN) {
2411 MGETHDR(m, M_DONTWAIT, MT_DATA);
2412 if (m == NULL)
2413 goto dropit;
2414 MCLAIM(m, &sc->sc_ethercom.ec_rx_mowner);
2415 memcpy(mtod(m, void *),
2416 mtod(rxs->rxs_mbuf, void *), len);
2417 sip_init_rxdesc(sc, i);
2418 bus_dmamap_sync(sc->sc_dmat, rxs->rxs_dmamap, 0,
2419 rxs->rxs_dmamap->dm_mapsize,
2420 BUS_DMASYNC_PREREAD);
2421 } else {
2422 m = rxs->rxs_mbuf;
2423 if (sipcom_add_rxbuf(sc, i) != 0) {
2424 dropit:
2425 if_statinc(ifp, if_ierrors);
2426 sip_init_rxdesc(sc, i);
2427 bus_dmamap_sync(sc->sc_dmat,
2428 rxs->rxs_dmamap, 0,
2429 rxs->rxs_dmamap->dm_mapsize,
2430 BUS_DMASYNC_PREREAD);
2431 continue;
2432 }
2433 }
2434 #else
2435 /*
2436 * The SiS 900's receive buffers must be 4-byte aligned.
2437 * But this means that the data after the Ethernet header
2438 * is misaligned. We must allocate a new buffer and
2439 * copy the data, shifted forward 2 bytes.
2440 */
2441 MGETHDR(m, M_DONTWAIT, MT_DATA);
2442 if (m == NULL) {
2443 dropit:
2444 if_statinc(ifp, if_ierrors);
2445 sip_init_rxdesc(sc, i);
2446 bus_dmamap_sync(sc->sc_dmat, rxs->rxs_dmamap, 0,
2447 rxs->rxs_dmamap->dm_mapsize, BUS_DMASYNC_PREREAD);
2448 continue;
2449 }
2450 MCLAIM(m, &sc->sc_ethercom.ec_rx_mowner);
2451 if (len > (MHLEN - 2)) {
2452 MCLGET(m, M_DONTWAIT);
2453 if ((m->m_flags & M_EXT) == 0) {
2454 m_freem(m);
2455 goto dropit;
2456 }
2457 }
2458 m->m_data += 2;
2459
2460 /*
2461 * Note that we use clusters for incoming frames, so the
2462 * buffer is virtually contiguous.
2463 */
2464 memcpy(mtod(m, void *), mtod(rxs->rxs_mbuf, void *), len);
2465
2466 /* Allow the receive descriptor to continue using its mbuf. */
2467 sip_init_rxdesc(sc, i);
2468 bus_dmamap_sync(sc->sc_dmat, rxs->rxs_dmamap, 0,
2469 rxs->rxs_dmamap->dm_mapsize, BUS_DMASYNC_PREREAD);
2470 #endif /* __NO_STRICT_ALIGNMENT */
2471
2472 m_set_rcvif(m, ifp);
2473 m->m_pkthdr.len = m->m_len = len;
2474
2475 /* Pass it on. */
2476 if_percpuq_enqueue(ifp->if_percpuq, m);
2477 }
2478
2479 /* Update the receive pointer. */
2480 sc->sc_rxptr = i;
2481 }
2482
2483 /*
2484 * sip_tick:
2485 *
2486 * One second timer, used to tick the MII.
2487 */
2488 static void
sipcom_tick(void * arg)2489 sipcom_tick(void *arg)
2490 {
2491 struct sip_softc *sc = arg;
2492 int s;
2493
2494 s = splnet();
2495 #ifdef SIP_EVENT_COUNTERS
2496 if (sc->sc_gigabit) {
2497 /* Read PAUSE related counts from MIB registers. */
2498 sc->sc_ev_rxpause.ev_count +=
2499 bus_space_read_4(sc->sc_st, sc->sc_sh,
2500 SIP_NS_MIB(MIB_RXPauseFrames)) & 0xffff;
2501 sc->sc_ev_txpause.ev_count +=
2502 bus_space_read_4(sc->sc_st, sc->sc_sh,
2503 SIP_NS_MIB(MIB_TXPauseFrames)) & 0xffff;
2504 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_NS_MIBC, MIBC_ACLR);
2505 }
2506 #endif /* SIP_EVENT_COUNTERS */
2507 mii_tick(&sc->sc_mii);
2508 splx(s);
2509
2510 callout_schedule(&sc->sc_tick_ch, hz);
2511 }
2512
2513 /*
2514 * sip_reset:
2515 *
2516 * Perform a soft reset on the SiS 900.
2517 */
2518 static bool
sipcom_reset(struct sip_softc * sc)2519 sipcom_reset(struct sip_softc *sc)
2520 {
2521 bus_space_tag_t st = sc->sc_st;
2522 bus_space_handle_t sh = sc->sc_sh;
2523 int i;
2524
2525 bus_space_write_4(st, sh, SIP_IER, 0);
2526 bus_space_write_4(st, sh, SIP_IMR, 0);
2527 bus_space_write_4(st, sh, SIP_RFCR, 0);
2528 bus_space_write_4(st, sh, SIP_CR, CR_RST);
2529
2530 for (i = 0; i < SIP_TIMEOUT; i++) {
2531 if ((bus_space_read_4(st, sh, SIP_CR) & CR_RST) == 0)
2532 break;
2533 delay(2);
2534 }
2535
2536 if (i == SIP_TIMEOUT) {
2537 printf("%s: reset failed to complete\n",
2538 device_xname(sc->sc_dev));
2539 return false;
2540 }
2541
2542 delay(1000);
2543
2544 if (sc->sc_gigabit) {
2545 /*
2546 * Set the general purpose I/O bits. Do it here in case we
2547 * need to have GPIO set up to talk to the media interface.
2548 */
2549 bus_space_write_4(st, sh, SIP_GPIOR, sc->sc_gpior);
2550 delay(1000);
2551 }
2552 return true;
2553 }
2554
2555 static void
sipcom_dp83820_init(struct sip_softc * sc,uint64_t capenable)2556 sipcom_dp83820_init(struct sip_softc *sc, uint64_t capenable)
2557 {
2558 uint32_t reg;
2559 bus_space_tag_t st = sc->sc_st;
2560 bus_space_handle_t sh = sc->sc_sh;
2561 /*
2562 * Initialize the VLAN/IP receive control register.
2563 * We enable checksum computation on all incoming
2564 * packets, and do not reject packets w/ bad checksums.
2565 */
2566 reg = 0;
2567 if (capenable &
2568 (IFCAP_CSUM_IPv4_Rx | IFCAP_CSUM_TCPv4_Rx | IFCAP_CSUM_UDPv4_Rx))
2569 reg |= VRCR_IPEN;
2570 if (VLAN_ATTACHED(&sc->sc_ethercom))
2571 reg |= VRCR_VTDEN | VRCR_VTREN;
2572 bus_space_write_4(st, sh, SIP_VRCR, reg);
2573
2574 /*
2575 * Initialize the VLAN/IP transmit control register.
2576 * We enable outgoing checksum computation on a
2577 * per-packet basis.
2578 */
2579 reg = 0;
2580 if (capenable &
2581 (IFCAP_CSUM_IPv4_Tx | IFCAP_CSUM_TCPv4_Tx | IFCAP_CSUM_UDPv4_Tx))
2582 reg |= VTCR_PPCHK;
2583 if (VLAN_ATTACHED(&sc->sc_ethercom))
2584 reg |= VTCR_VPPTI;
2585 bus_space_write_4(st, sh, SIP_VTCR, reg);
2586
2587 /*
2588 * If we're using VLANs, initialize the VLAN data register.
2589 * To understand why we bswap the VLAN Ethertype, see section
2590 * 4.2.36 of the DP83820 manual.
2591 */
2592 if (VLAN_ATTACHED(&sc->sc_ethercom))
2593 bus_space_write_4(st, sh, SIP_VDR, bswap16(ETHERTYPE_VLAN));
2594 }
2595
2596 /*
2597 * sip_init: [ ifnet interface function ]
2598 *
2599 * Initialize the interface. Must be called at splnet().
2600 */
2601 static int
sipcom_init(struct ifnet * ifp)2602 sipcom_init(struct ifnet *ifp)
2603 {
2604 struct sip_softc *sc = ifp->if_softc;
2605 bus_space_tag_t st = sc->sc_st;
2606 bus_space_handle_t sh = sc->sc_sh;
2607 struct sip_txsoft *txs;
2608 struct sip_rxsoft *rxs;
2609 int i, error = 0;
2610
2611 if (device_is_active(sc->sc_dev)) {
2612 /*
2613 * Cancel any pending I/O.
2614 */
2615 sipcom_stop(ifp, 0);
2616 } else if (!pmf_device_subtree_resume(sc->sc_dev, &sc->sc_qual) ||
2617 !device_is_active(sc->sc_dev))
2618 return 0;
2619
2620 /*
2621 * Reset the chip to a known state.
2622 */
2623 if (!sipcom_reset(sc))
2624 return EBUSY;
2625
2626 if (SIP_CHIP_MODEL(sc, PCI_VENDOR_NS, PCI_PRODUCT_NS_DP83815)) {
2627 /*
2628 * DP83815 manual, page 78:
2629 * 4.4 Recommended Registers Configuration
2630 * For optimum performance of the DP83815, version noted
2631 * as DP83815CVNG (SRR = 203h), the listed register
2632 * modifications must be followed in sequence...
2633 *
2634 * It's not clear if this should be 302h or 203h because that
2635 * chip name is listed as SRR 302h in the description of the
2636 * SRR register. However, my revision 302h DP83815 on the
2637 * Netgear FA311 purchased in 02/2001 needs these settings
2638 * to avoid tons of errors in AcceptPerfectMatch (non-
2639 * IFF_PROMISC) mode. I do not know if other revisions need
2640 * this set or not. [briggs -- 09 March 2001]
2641 *
2642 * Note that only the low-order 12 bits of 0xe4 are documented
2643 * and that this sets reserved bits in that register.
2644 */
2645 bus_space_write_4(st, sh, 0x00cc, 0x0001);
2646
2647 bus_space_write_4(st, sh, 0x00e4, 0x189C);
2648 bus_space_write_4(st, sh, 0x00fc, 0x0000);
2649 bus_space_write_4(st, sh, 0x00f4, 0x5040);
2650 bus_space_write_4(st, sh, 0x00f8, 0x008c);
2651
2652 bus_space_write_4(st, sh, 0x00cc, 0x0000);
2653 }
2654
2655 /* Initialize the transmit descriptor ring. */
2656 sip_init_txring(sc);
2657
2658 /*
2659 * Initialize the transmit job descriptors.
2660 */
2661 SIMPLEQ_INIT(&sc->sc_txfreeq);
2662 SIMPLEQ_INIT(&sc->sc_txdirtyq);
2663 for (i = 0; i < SIP_TXQUEUELEN; i++) {
2664 txs = &sc->sc_txsoft[i];
2665 txs->txs_mbuf = NULL;
2666 SIMPLEQ_INSERT_TAIL(&sc->sc_txfreeq, txs, txs_q);
2667 }
2668
2669 /*
2670 * Initialize the receive descriptor and receive job
2671 * descriptor rings.
2672 */
2673 for (i = 0; i < sc->sc_parm->p_nrxdesc; i++) {
2674 rxs = &sc->sc_rxsoft[i];
2675 if (rxs->rxs_mbuf == NULL) {
2676 if ((error = sipcom_add_rxbuf(sc, i)) != 0) {
2677 printf("%s: unable to allocate or map rx "
2678 "buffer %d, error = %d\n",
2679 device_xname(sc->sc_dev), i, error);
2680 /*
2681 * XXX Should attempt to run with fewer receive
2682 * XXX buffers instead of just failing.
2683 */
2684 sipcom_rxdrain(sc);
2685 goto out;
2686 }
2687 } else
2688 sip_init_rxdesc(sc, i);
2689 }
2690 sc->sc_rxptr = 0;
2691 sc->sc_rxdiscard = 0;
2692 sip_rxchain_reset(sc);
2693
2694 /*
2695 * Set the configuration register; it's already initialized
2696 * in sip_attach().
2697 */
2698 bus_space_write_4(st, sh, SIP_CFG, sc->sc_cfg);
2699
2700 /*
2701 * Initialize the prototype TXCFG register.
2702 */
2703 if (sc->sc_gigabit) {
2704 sc->sc_txcfg = sc->sc_bits.b_txcfg_mxdma_512;
2705 sc->sc_rxcfg = sc->sc_bits.b_rxcfg_mxdma_512;
2706 } else if ((SIP_SIS900_REV(sc, SIS_REV_635) ||
2707 SIP_SIS900_REV(sc, SIS_REV_960) ||
2708 SIP_SIS900_REV(sc, SIS_REV_900B)) &&
2709 (sc->sc_cfg & CFG_EDBMASTEN)) {
2710 sc->sc_txcfg = sc->sc_bits.b_txcfg_mxdma_64;
2711 sc->sc_rxcfg = sc->sc_bits.b_rxcfg_mxdma_64;
2712 } else {
2713 sc->sc_txcfg = sc->sc_bits.b_txcfg_mxdma_512;
2714 sc->sc_rxcfg = sc->sc_bits.b_rxcfg_mxdma_512;
2715 }
2716
2717 sc->sc_txcfg |= TXCFG_ATP |
2718 __SHIFTIN(sc->sc_tx_fill_thresh, sc->sc_bits.b_txcfg_flth_mask) |
2719 sc->sc_tx_drain_thresh;
2720 bus_space_write_4(st, sh, sc->sc_regs.r_txcfg, sc->sc_txcfg);
2721
2722 /*
2723 * Initialize the receive drain threshold if we have never
2724 * done so.
2725 */
2726 if (sc->sc_rx_drain_thresh == 0) {
2727 /*
2728 * XXX This value should be tuned. This is set to the
2729 * maximum of 248 bytes, and we may be able to improve
2730 * performance by decreasing it (although we should never
2731 * set this value lower than 2; 14 bytes are required to
2732 * filter the packet).
2733 */
2734 sc->sc_rx_drain_thresh = __SHIFTOUT_MASK(RXCFG_DRTH_MASK);
2735 }
2736
2737 /*
2738 * Initialize the prototype RXCFG register.
2739 */
2740 sc->sc_rxcfg |= __SHIFTIN(sc->sc_rx_drain_thresh, RXCFG_DRTH_MASK);
2741 /*
2742 * Accept long packets (including FCS) so we can handle
2743 * 802.1q-tagged frames and jumbo frames properly.
2744 */
2745 if ((sc->sc_gigabit && ifp->if_mtu > ETHERMTU) ||
2746 (sc->sc_ethercom.ec_capenable & ETHERCAP_VLAN_MTU))
2747 sc->sc_rxcfg |= RXCFG_ALP;
2748
2749 /*
2750 * Checksum offloading is disabled if the user selects an MTU
2751 * larger than 8109. (FreeBSD says 8152, but there is empirical
2752 * evidence that >8109 does not work on some boards, such as the
2753 * Planex GN-1000TE).
2754 */
2755 if (sc->sc_gigabit && ifp->if_mtu > 8109 &&
2756 (ifp->if_capenable &
2757 (IFCAP_CSUM_IPv4_Tx | IFCAP_CSUM_IPv4_Rx |
2758 IFCAP_CSUM_TCPv4_Tx | IFCAP_CSUM_TCPv4_Rx |
2759 IFCAP_CSUM_UDPv4_Tx | IFCAP_CSUM_UDPv4_Rx))) {
2760 printf("%s: Checksum offloading does not work if MTU > 8109 - "
2761 "disabled.\n", device_xname(sc->sc_dev));
2762 ifp->if_capenable &=
2763 ~(IFCAP_CSUM_IPv4_Tx | IFCAP_CSUM_IPv4_Rx |
2764 IFCAP_CSUM_TCPv4_Tx | IFCAP_CSUM_TCPv4_Rx |
2765 IFCAP_CSUM_UDPv4_Tx | IFCAP_CSUM_UDPv4_Rx);
2766 ifp->if_csum_flags_tx = 0;
2767 ifp->if_csum_flags_rx = 0;
2768 }
2769
2770 bus_space_write_4(st, sh, sc->sc_regs.r_rxcfg, sc->sc_rxcfg);
2771
2772 if (sc->sc_gigabit)
2773 sipcom_dp83820_init(sc, ifp->if_capenable);
2774
2775 /*
2776 * Give the transmit and receive rings to the chip.
2777 */
2778 sip_set_txdp(sc, SIP_CDTXADDR(sc, sc->sc_txnext));
2779 sip_set_rxdp(sc, SIP_CDRXADDR(sc, sc->sc_rxptr));
2780
2781 /*
2782 * Initialize the interrupt mask.
2783 */
2784 sc->sc_imr = sc->sc_bits.b_isr_dperr |
2785 sc->sc_bits.b_isr_sserr |
2786 sc->sc_bits.b_isr_rmabt |
2787 sc->sc_bits.b_isr_rtabt |
2788 ISR_RXSOVR | ISR_TXURN | ISR_TXDESC | ISR_TXIDLE | ISR_RXORN |
2789 ISR_RXIDLE | ISR_RXDESC;
2790 bus_space_write_4(st, sh, SIP_IMR, sc->sc_imr);
2791
2792 /* Set up the receive filter. */
2793 (*sc->sc_model->sip_variant->sipv_set_filter)(sc);
2794
2795 /*
2796 * Tune sc_rx_flow_thresh.
2797 * XXX "More than 8KB" is too short for jumbo frames.
2798 * XXX TODO: Threshold value should be user-settable.
2799 */
2800 sc->sc_rx_flow_thresh = (PCR_PS_STHI_8 | PCR_PS_STLO_4 |
2801 PCR_PS_FFHI_8 | PCR_PS_FFLO_4 |
2802 (PCR_PAUSE_CNT & PCR_PAUSE_CNT_MASK));
2803
2804 /*
2805 * Set the current media. Do this after initializing the prototype
2806 * IMR, since sip_mii_statchg() modifies the IMR for 802.3x flow
2807 * control.
2808 */
2809 if ((error = ether_mediachange(ifp)) != 0)
2810 goto out;
2811
2812 /*
2813 * Set the interrupt hold-off timer to 100us.
2814 */
2815 if (sc->sc_gigabit)
2816 bus_space_write_4(st, sh, SIP_IHR, 0x01);
2817
2818 /*
2819 * Enable interrupts.
2820 */
2821 bus_space_write_4(st, sh, SIP_IER, IER_IE);
2822
2823 /*
2824 * Start the transmit and receive processes.
2825 */
2826 bus_space_write_4(st, sh, SIP_CR, CR_RXE | CR_TXE);
2827
2828 /*
2829 * Start the one second MII clock.
2830 */
2831 callout_schedule(&sc->sc_tick_ch, hz);
2832
2833 /*
2834 * ...all done!
2835 */
2836 ifp->if_flags |= IFF_RUNNING;
2837 sc->sc_if_flags = ifp->if_flags;
2838 sc->sc_prev.ec_capenable = sc->sc_ethercom.ec_capenable;
2839 sc->sc_prev.is_vlan = VLAN_ATTACHED(&(sc)->sc_ethercom);
2840 sc->sc_prev.if_capenable = ifp->if_capenable;
2841
2842 out:
2843 if (error)
2844 printf("%s: interface not running\n", device_xname(sc->sc_dev));
2845 return error;
2846 }
2847
2848 /*
2849 * sip_drain:
2850 *
2851 * Drain the receive queue.
2852 */
2853 static void
sipcom_rxdrain(struct sip_softc * sc)2854 sipcom_rxdrain(struct sip_softc *sc)
2855 {
2856 struct sip_rxsoft *rxs;
2857 int i;
2858
2859 for (i = 0; i < sc->sc_parm->p_nrxdesc; i++) {
2860 rxs = &sc->sc_rxsoft[i];
2861 if (rxs->rxs_mbuf != NULL) {
2862 bus_dmamap_unload(sc->sc_dmat, rxs->rxs_dmamap);
2863 m_freem(rxs->rxs_mbuf);
2864 rxs->rxs_mbuf = NULL;
2865 }
2866 }
2867 }
2868
2869 /*
2870 * sip_stop: [ ifnet interface function ]
2871 *
2872 * Stop transmission on the interface.
2873 */
2874 static void
sipcom_stop(struct ifnet * ifp,int disable)2875 sipcom_stop(struct ifnet *ifp, int disable)
2876 {
2877 struct sip_softc *sc = ifp->if_softc;
2878 bus_space_tag_t st = sc->sc_st;
2879 bus_space_handle_t sh = sc->sc_sh;
2880 struct sip_txsoft *txs;
2881 uint32_t cmdsts = 0; /* DEBUG */
2882
2883 /*
2884 * Stop the one second clock.
2885 */
2886 callout_stop(&sc->sc_tick_ch);
2887
2888 /* Down the MII. */
2889 mii_down(&sc->sc_mii);
2890
2891 if (device_is_active(sc->sc_dev)) {
2892 /*
2893 * Disable interrupts.
2894 */
2895 bus_space_write_4(st, sh, SIP_IER, 0);
2896
2897 /*
2898 * Stop receiver and transmitter.
2899 */
2900 bus_space_write_4(st, sh, SIP_CR, CR_RXD | CR_TXD);
2901 }
2902
2903 /*
2904 * Release any queued transmit buffers.
2905 */
2906 while ((txs = SIMPLEQ_FIRST(&sc->sc_txdirtyq)) != NULL) {
2907 if ((ifp->if_flags & IFF_DEBUG) != 0 &&
2908 SIMPLEQ_NEXT(txs, txs_q) == NULL &&
2909 (sc->sc_txdescs[
2910 txs->txs_lastdesc].sipd_words[
2911 sc->sc_cmdsts_idx] & htole32(CMDSTS_INTR)) == 0)
2912 printf("%s: sip_stop: last descriptor does not "
2913 "have INTR bit set\n", device_xname(sc->sc_dev));
2914 SIMPLEQ_REMOVE_HEAD(&sc->sc_txdirtyq, txs_q);
2915 #ifdef DIAGNOSTIC
2916 if (txs->txs_mbuf == NULL) {
2917 printf("%s: dirty txsoft with no mbuf chain\n",
2918 device_xname(sc->sc_dev));
2919 panic("sip_stop");
2920 }
2921 #endif
2922 cmdsts |= /* DEBUG */
2923 le32toh(sc->sc_txdescs[
2924 txs->txs_lastdesc].sipd_words[sc->sc_cmdsts_idx]);
2925 bus_dmamap_unload(sc->sc_dmat, txs->txs_dmamap);
2926 m_freem(txs->txs_mbuf);
2927 txs->txs_mbuf = NULL;
2928 SIMPLEQ_INSERT_TAIL(&sc->sc_txfreeq, txs, txs_q);
2929 }
2930
2931 /*
2932 * Mark the interface down and cancel the watchdog timer.
2933 */
2934 ifp->if_flags &= ~IFF_RUNNING;
2935 ifp->if_timer = 0;
2936
2937 if (disable)
2938 pmf_device_recursive_suspend(sc->sc_dev, &sc->sc_qual);
2939
2940 if ((ifp->if_flags & IFF_DEBUG) != 0 &&
2941 (cmdsts & CMDSTS_INTR) == 0 && sc->sc_txfree != sc->sc_ntxdesc)
2942 printf("%s: sip_stop: no INTR bits set in dirty tx "
2943 "descriptors\n", device_xname(sc->sc_dev));
2944 }
2945
2946 /*
2947 * sip_read_eeprom:
2948 *
2949 * Read data from the serial EEPROM.
2950 */
2951 static void
sipcom_read_eeprom(struct sip_softc * sc,int word,int wordcnt,uint16_t * data)2952 sipcom_read_eeprom(struct sip_softc *sc, int word, int wordcnt,
2953 uint16_t *data)
2954 {
2955 bus_space_tag_t st = sc->sc_st;
2956 bus_space_handle_t sh = sc->sc_sh;
2957 uint16_t reg;
2958 int i, x;
2959
2960 for (i = 0; i < wordcnt; i++) {
2961 /* Send CHIP SELECT. */
2962 reg = EROMAR_EECS;
2963 bus_space_write_4(st, sh, SIP_EROMAR, reg);
2964
2965 /* Shift in the READ opcode. */
2966 for (x = 3; x > 0; x--) {
2967 if (SIP_EEPROM_OPC_READ & (1 << (x - 1)))
2968 reg |= EROMAR_EEDI;
2969 else
2970 reg &= ~EROMAR_EEDI;
2971 bus_space_write_4(st, sh, SIP_EROMAR, reg);
2972 bus_space_write_4(st, sh, SIP_EROMAR,
2973 reg | EROMAR_EESK);
2974 delay(4);
2975 bus_space_write_4(st, sh, SIP_EROMAR, reg);
2976 delay(4);
2977 }
2978
2979 /* Shift in address. */
2980 for (x = 6; x > 0; x--) {
2981 if ((word + i) & (1 << (x - 1)))
2982 reg |= EROMAR_EEDI;
2983 else
2984 reg &= ~EROMAR_EEDI;
2985 bus_space_write_4(st, sh, SIP_EROMAR, reg);
2986 bus_space_write_4(st, sh, SIP_EROMAR,
2987 reg | EROMAR_EESK);
2988 delay(4);
2989 bus_space_write_4(st, sh, SIP_EROMAR, reg);
2990 delay(4);
2991 }
2992
2993 /* Shift out data. */
2994 reg = EROMAR_EECS;
2995 data[i] = 0;
2996 for (x = 16; x > 0; x--) {
2997 bus_space_write_4(st, sh, SIP_EROMAR,
2998 reg | EROMAR_EESK);
2999 delay(4);
3000 if (bus_space_read_4(st, sh, SIP_EROMAR) & EROMAR_EEDO)
3001 data[i] |= (1 << (x - 1));
3002 bus_space_write_4(st, sh, SIP_EROMAR, reg);
3003 delay(4);
3004 }
3005
3006 /* Clear CHIP SELECT. */
3007 bus_space_write_4(st, sh, SIP_EROMAR, 0);
3008 delay(4);
3009 }
3010 }
3011
3012 /*
3013 * sipcom_add_rxbuf:
3014 *
3015 * Add a receive buffer to the indicated descriptor.
3016 */
3017 static int
sipcom_add_rxbuf(struct sip_softc * sc,int idx)3018 sipcom_add_rxbuf(struct sip_softc *sc, int idx)
3019 {
3020 struct sip_rxsoft *rxs = &sc->sc_rxsoft[idx];
3021 struct mbuf *m;
3022 int error;
3023
3024 MGETHDR(m, M_DONTWAIT, MT_DATA);
3025 if (m == NULL)
3026 return ENOBUFS;
3027 MCLAIM(m, &sc->sc_ethercom.ec_rx_mowner);
3028
3029 MCLGET(m, M_DONTWAIT);
3030 if ((m->m_flags & M_EXT) == 0) {
3031 m_freem(m);
3032 return ENOBUFS;
3033 }
3034
3035 /* XXX I don't believe this is necessary. --dyoung */
3036 if (sc->sc_gigabit)
3037 m->m_len = sc->sc_parm->p_rxbuf_len;
3038
3039 if (rxs->rxs_mbuf != NULL)
3040 bus_dmamap_unload(sc->sc_dmat, rxs->rxs_dmamap);
3041
3042 rxs->rxs_mbuf = m;
3043
3044 error = bus_dmamap_load(sc->sc_dmat, rxs->rxs_dmamap,
3045 m->m_ext.ext_buf, m->m_ext.ext_size, NULL,
3046 BUS_DMA_READ | BUS_DMA_NOWAIT);
3047 if (error) {
3048 printf("%s: can't load rx DMA map %d, error = %d\n",
3049 device_xname(sc->sc_dev), idx, error);
3050 panic("%s", __func__); /* XXX */
3051 }
3052
3053 bus_dmamap_sync(sc->sc_dmat, rxs->rxs_dmamap, 0,
3054 rxs->rxs_dmamap->dm_mapsize, BUS_DMASYNC_PREREAD);
3055
3056 sip_init_rxdesc(sc, idx);
3057
3058 return 0;
3059 }
3060
3061 /*
3062 * sip_sis900_set_filter:
3063 *
3064 * Set up the receive filter.
3065 */
3066 static void
sipcom_sis900_set_filter(struct sip_softc * sc)3067 sipcom_sis900_set_filter(struct sip_softc *sc)
3068 {
3069 bus_space_tag_t st = sc->sc_st;
3070 bus_space_handle_t sh = sc->sc_sh;
3071 struct ethercom *ec = &sc->sc_ethercom;
3072 struct ifnet *ifp = &sc->sc_ethercom.ec_if;
3073 struct ether_multi *enm;
3074 const uint8_t *cp;
3075 struct ether_multistep step;
3076 uint32_t crc, mchash[16];
3077
3078 /*
3079 * Initialize the prototype RFCR.
3080 */
3081 sc->sc_rfcr = RFCR_RFEN;
3082 if (ifp->if_flags & IFF_BROADCAST)
3083 sc->sc_rfcr |= RFCR_AAB;
3084 if (ifp->if_flags & IFF_PROMISC) {
3085 sc->sc_rfcr |= RFCR_AAP;
3086 goto allmulti;
3087 }
3088
3089 /*
3090 * Set up the multicast address filter by passing all multicast
3091 * addresses through a CRC generator, and then using the high-order
3092 * 6 bits as an index into the 128 bit multicast hash table (only
3093 * the lower 16 bits of each 32 bit multicast hash register are
3094 * valid). The high order bits select the register, while the
3095 * rest of the bits select the bit within the register.
3096 */
3097
3098 memset(mchash, 0, sizeof(mchash));
3099
3100 /*
3101 * SiS900 (at least SiS963) requires us to register the address of
3102 * the PAUSE packet (01:80:c2:00:00:01) into the address filter.
3103 */
3104 crc = 0x0ed423f9;
3105
3106 if (SIP_SIS900_REV(sc, SIS_REV_635) ||
3107 SIP_SIS900_REV(sc, SIS_REV_960) ||
3108 SIP_SIS900_REV(sc, SIS_REV_900B)) {
3109 /* Just want the 8 most significant bits. */
3110 crc >>= 24;
3111 } else {
3112 /* Just want the 7 most significant bits. */
3113 crc >>= 25;
3114 }
3115
3116 /* Set the corresponding bit in the hash table. */
3117 mchash[crc >> 4] |= 1 << (crc & 0xf);
3118
3119 ETHER_LOCK(ec);
3120 ETHER_FIRST_MULTI(step, ec, enm);
3121 while (enm != NULL) {
3122 if (memcmp(enm->enm_addrlo, enm->enm_addrhi, ETHER_ADDR_LEN)) {
3123 /*
3124 * We must listen to a range of multicast addresses.
3125 * For now, just accept all multicasts, rather than
3126 * trying to set only those filter bits needed to match
3127 * the range. (At this time, the only use of address
3128 * ranges is for IP multicast routing, for which the
3129 * range is big enough to require all bits set.)
3130 */
3131 ETHER_UNLOCK(ec);
3132 goto allmulti;
3133 }
3134
3135 crc = ether_crc32_be(enm->enm_addrlo, ETHER_ADDR_LEN);
3136
3137 if (SIP_SIS900_REV(sc, SIS_REV_635) ||
3138 SIP_SIS900_REV(sc, SIS_REV_960) ||
3139 SIP_SIS900_REV(sc, SIS_REV_900B)) {
3140 /* Just want the 8 most significant bits. */
3141 crc >>= 24;
3142 } else {
3143 /* Just want the 7 most significant bits. */
3144 crc >>= 25;
3145 }
3146
3147 /* Set the corresponding bit in the hash table. */
3148 mchash[crc >> 4] |= 1 << (crc & 0xf);
3149
3150 ETHER_NEXT_MULTI(step, enm);
3151 }
3152 ETHER_UNLOCK(ec);
3153
3154 ifp->if_flags &= ~IFF_ALLMULTI;
3155 goto setit;
3156
3157 allmulti:
3158 ifp->if_flags |= IFF_ALLMULTI;
3159 sc->sc_rfcr |= RFCR_AAM;
3160
3161 setit:
3162 #define FILTER_EMIT(addr, data) \
3163 bus_space_write_4(st, sh, SIP_RFCR, (addr)); \
3164 delay(1); \
3165 bus_space_write_4(st, sh, SIP_RFDR, (data)); \
3166 delay(1)
3167
3168 /*
3169 * Disable receive filter, and program the node address.
3170 */
3171 cp = CLLADDR(ifp->if_sadl);
3172 FILTER_EMIT(RFCR_RFADDR_NODE0, (cp[1] << 8) | cp[0]);
3173 FILTER_EMIT(RFCR_RFADDR_NODE2, (cp[3] << 8) | cp[2]);
3174 FILTER_EMIT(RFCR_RFADDR_NODE4, (cp[5] << 8) | cp[4]);
3175
3176 if ((ifp->if_flags & IFF_ALLMULTI) == 0) {
3177 /*
3178 * Program the multicast hash table.
3179 */
3180 FILTER_EMIT(RFCR_RFADDR_MC0, mchash[0]);
3181 FILTER_EMIT(RFCR_RFADDR_MC1, mchash[1]);
3182 FILTER_EMIT(RFCR_RFADDR_MC2, mchash[2]);
3183 FILTER_EMIT(RFCR_RFADDR_MC3, mchash[3]);
3184 FILTER_EMIT(RFCR_RFADDR_MC4, mchash[4]);
3185 FILTER_EMIT(RFCR_RFADDR_MC5, mchash[5]);
3186 FILTER_EMIT(RFCR_RFADDR_MC6, mchash[6]);
3187 FILTER_EMIT(RFCR_RFADDR_MC7, mchash[7]);
3188 if (SIP_SIS900_REV(sc, SIS_REV_635) ||
3189 SIP_SIS900_REV(sc, SIS_REV_960) ||
3190 SIP_SIS900_REV(sc, SIS_REV_900B)) {
3191 FILTER_EMIT(RFCR_RFADDR_MC8, mchash[8]);
3192 FILTER_EMIT(RFCR_RFADDR_MC9, mchash[9]);
3193 FILTER_EMIT(RFCR_RFADDR_MC10, mchash[10]);
3194 FILTER_EMIT(RFCR_RFADDR_MC11, mchash[11]);
3195 FILTER_EMIT(RFCR_RFADDR_MC12, mchash[12]);
3196 FILTER_EMIT(RFCR_RFADDR_MC13, mchash[13]);
3197 FILTER_EMIT(RFCR_RFADDR_MC14, mchash[14]);
3198 FILTER_EMIT(RFCR_RFADDR_MC15, mchash[15]);
3199 }
3200 }
3201 #undef FILTER_EMIT
3202
3203 /*
3204 * Re-enable the receiver filter.
3205 */
3206 bus_space_write_4(st, sh, SIP_RFCR, sc->sc_rfcr);
3207 }
3208
3209 /*
3210 * sip_dp83815_set_filter:
3211 *
3212 * Set up the receive filter.
3213 */
3214 static void
sipcom_dp83815_set_filter(struct sip_softc * sc)3215 sipcom_dp83815_set_filter(struct sip_softc *sc)
3216 {
3217 bus_space_tag_t st = sc->sc_st;
3218 bus_space_handle_t sh = sc->sc_sh;
3219 struct ethercom *ec = &sc->sc_ethercom;
3220 struct ifnet *ifp = &sc->sc_ethercom.ec_if;
3221 struct ether_multi *enm;
3222 const uint8_t *cp;
3223 struct ether_multistep step;
3224 uint32_t crc, hash, slot, bit;
3225 #define MCHASH_NWORDS_83820 128
3226 #define MCHASH_NWORDS_83815 32
3227 #define MCHASH_NWORDS MAX(MCHASH_NWORDS_83820, MCHASH_NWORDS_83815)
3228 uint16_t mchash[MCHASH_NWORDS];
3229 int i;
3230
3231 /*
3232 * Initialize the prototype RFCR.
3233 * Enable the receive filter, and accept on
3234 * Perfect (destination address) Match
3235 * If IFF_BROADCAST, also accept all broadcast packets.
3236 * If IFF_PROMISC, accept all unicast packets (and later, set
3237 * IFF_ALLMULTI and accept all multicast, too).
3238 */
3239 sc->sc_rfcr = RFCR_RFEN | RFCR_APM;
3240 if (ifp->if_flags & IFF_BROADCAST)
3241 sc->sc_rfcr |= RFCR_AAB;
3242 if (ifp->if_flags & IFF_PROMISC) {
3243 sc->sc_rfcr |= RFCR_AAP;
3244 goto allmulti;
3245 }
3246
3247 /*
3248 * Set up the DP83820/DP83815 multicast address filter by
3249 * passing all multicast addresses through a CRC generator,
3250 * and then using the high-order 11/9 bits as an index into
3251 * the 2048/512 bit multicast hash table. The high-order
3252 * 7/5 bits select the slot, while the low-order 4 bits
3253 * select the bit within the slot. Note that only the low
3254 * 16-bits of each filter word are used, and there are
3255 * 128/32 filter words.
3256 */
3257
3258 memset(mchash, 0, sizeof(mchash));
3259
3260 ifp->if_flags &= ~IFF_ALLMULTI;
3261 ETHER_FIRST_MULTI(step, ec, enm);
3262 if (enm == NULL)
3263 goto setit;
3264 while (enm != NULL) {
3265 if (memcmp(enm->enm_addrlo, enm->enm_addrhi, ETHER_ADDR_LEN)) {
3266 /*
3267 * We must listen to a range of multicast addresses.
3268 * For now, just accept all multicasts, rather than
3269 * trying to set only those filter bits needed to match
3270 * the range. (At this time, the only use of address
3271 * ranges is for IP multicast routing, for which the
3272 * range is big enough to require all bits set.)
3273 */
3274 goto allmulti;
3275 }
3276
3277 crc = ether_crc32_be(enm->enm_addrlo, ETHER_ADDR_LEN);
3278
3279 if (sc->sc_gigabit) {
3280 /* Just want the 11 most significant bits. */
3281 hash = crc >> 21;
3282 } else {
3283 /* Just want the 9 most significant bits. */
3284 hash = crc >> 23;
3285 }
3286
3287 slot = hash >> 4;
3288 bit = hash & 0xf;
3289
3290 /* Set the corresponding bit in the hash table. */
3291 mchash[slot] |= 1 << bit;
3292
3293 ETHER_NEXT_MULTI(step, enm);
3294 }
3295 sc->sc_rfcr |= RFCR_MHEN;
3296 goto setit;
3297
3298 allmulti:
3299 ifp->if_flags |= IFF_ALLMULTI;
3300 sc->sc_rfcr |= RFCR_AAM;
3301
3302 setit:
3303 #define FILTER_EMIT(addr, data) \
3304 bus_space_write_4(st, sh, SIP_RFCR, (addr)); \
3305 delay(1); \
3306 bus_space_write_4(st, sh, SIP_RFDR, (data)); \
3307 delay(1)
3308
3309 /*
3310 * Disable receive filter, and program the node address.
3311 */
3312 cp = CLLADDR(ifp->if_sadl);
3313 FILTER_EMIT(RFCR_NS_RFADDR_PMATCH0, (cp[1] << 8) | cp[0]);
3314 FILTER_EMIT(RFCR_NS_RFADDR_PMATCH2, (cp[3] << 8) | cp[2]);
3315 FILTER_EMIT(RFCR_NS_RFADDR_PMATCH4, (cp[5] << 8) | cp[4]);
3316
3317 if ((ifp->if_flags & IFF_ALLMULTI) == 0) {
3318 int nwords =
3319 sc->sc_gigabit ? MCHASH_NWORDS_83820 : MCHASH_NWORDS_83815;
3320 /*
3321 * Program the multicast hash table.
3322 */
3323 for (i = 0; i < nwords; i++) {
3324 FILTER_EMIT(sc->sc_parm->p_filtmem + (i * 2), mchash[i]);
3325 }
3326 }
3327 #undef FILTER_EMIT
3328 #undef MCHASH_NWORDS
3329 #undef MCHASH_NWORDS_83815
3330 #undef MCHASH_NWORDS_83820
3331
3332 /*
3333 * Re-enable the receiver filter.
3334 */
3335 bus_space_write_4(st, sh, SIP_RFCR, sc->sc_rfcr);
3336 }
3337
3338 /*
3339 * sip_dp83820_mii_readreg: [mii interface function]
3340 *
3341 * Read a PHY register on the MII of the DP83820.
3342 */
3343 static int
sipcom_dp83820_mii_readreg(device_t self,int phy,int reg,uint16_t * val)3344 sipcom_dp83820_mii_readreg(device_t self, int phy, int reg, uint16_t *val)
3345 {
3346 struct sip_softc *sc = device_private(self);
3347
3348 if (sc->sc_cfg & CFG_TBI_EN) {
3349 bus_addr_t tbireg;
3350
3351 if (phy != 0)
3352 return -1;
3353
3354 switch (reg) {
3355 case MII_BMCR: tbireg = SIP_TBICR; break;
3356 case MII_BMSR: tbireg = SIP_TBISR; break;
3357 case MII_ANAR: tbireg = SIP_TANAR; break;
3358 case MII_ANLPAR: tbireg = SIP_TANLPAR; break;
3359 case MII_ANER: tbireg = SIP_TANER; break;
3360 case MII_EXTSR:
3361 /*
3362 * Don't even bother reading the TESR register.
3363 * The manual documents that the device has
3364 * 1000baseX full/half capability, but the
3365 * register itself seems read back 0 on some
3366 * boards. Just hard-code the result.
3367 */
3368 *val = (EXTSR_1000XFDX | EXTSR_1000XHDX);
3369 return 0;
3370
3371 default:
3372 return 0;
3373 }
3374
3375 *val = bus_space_read_4(sc->sc_st, sc->sc_sh, tbireg) & 0xffff;
3376 if (tbireg == SIP_TBISR) {
3377 /* LINK and ACOMP are switched! */
3378 int sr = *val;
3379
3380 *val = 0;
3381 if (sr & TBISR_MR_LINK_STATUS)
3382 *val |= BMSR_LINK;
3383 if (sr & TBISR_MR_AN_COMPLETE)
3384 *val |= BMSR_ACOMP;
3385
3386 /*
3387 * The manual claims this register reads back 0
3388 * on hard and soft reset. But we want to let
3389 * the gentbi driver know that we support auto-
3390 * negotiation, so hard-code this bit in the
3391 * result.
3392 */
3393 *val |= BMSR_ANEG | BMSR_EXTSTAT;
3394 }
3395
3396 return 0;
3397 }
3398
3399 return mii_bitbang_readreg(self, &sipcom_mii_bitbang_ops, phy, reg,
3400 val);
3401 }
3402
3403 /*
3404 * sip_dp83820_mii_writereg: [mii interface function]
3405 *
3406 * Write a PHY register on the MII of the DP83820.
3407 */
3408 static int
sipcom_dp83820_mii_writereg(device_t self,int phy,int reg,uint16_t val)3409 sipcom_dp83820_mii_writereg(device_t self, int phy, int reg, uint16_t val)
3410 {
3411 struct sip_softc *sc = device_private(self);
3412
3413 if (sc->sc_cfg & CFG_TBI_EN) {
3414 bus_addr_t tbireg;
3415
3416 if (phy != 0)
3417 return -1;
3418
3419 switch (reg) {
3420 case MII_BMCR: tbireg = SIP_TBICR; break;
3421 case MII_ANAR: tbireg = SIP_TANAR; break;
3422 case MII_ANLPAR: tbireg = SIP_TANLPAR; break;
3423 default:
3424 return 0;
3425 }
3426
3427 bus_space_write_4(sc->sc_st, sc->sc_sh, tbireg, val);
3428 return 0;
3429 }
3430
3431 return mii_bitbang_writereg(self, &sipcom_mii_bitbang_ops, phy, reg,
3432 val);
3433 }
3434
3435 /*
3436 * sip_dp83820_mii_statchg: [mii interface function]
3437 *
3438 * Callback from MII layer when media changes.
3439 */
3440 static void
sipcom_dp83820_mii_statchg(struct ifnet * ifp)3441 sipcom_dp83820_mii_statchg(struct ifnet *ifp)
3442 {
3443 struct sip_softc *sc = ifp->if_softc;
3444 struct mii_data *mii = &sc->sc_mii;
3445 uint32_t cfg, pcr;
3446
3447 /*
3448 * Get flow control negotiation result.
3449 */
3450 if (IFM_SUBTYPE(mii->mii_media.ifm_cur->ifm_media) == IFM_AUTO &&
3451 (mii->mii_media_active & IFM_ETH_FMASK) != sc->sc_flowflags) {
3452 sc->sc_flowflags = mii->mii_media_active & IFM_ETH_FMASK;
3453 mii->mii_media_active &= ~IFM_ETH_FMASK;
3454 }
3455
3456 /*
3457 * Update TXCFG for full-duplex operation.
3458 */
3459 if ((mii->mii_media_active & IFM_FDX) != 0)
3460 sc->sc_txcfg |= (TXCFG_CSI | TXCFG_HBI);
3461 else
3462 sc->sc_txcfg &= ~(TXCFG_CSI | TXCFG_HBI);
3463
3464 /*
3465 * Update RXCFG for full-duplex or loopback.
3466 */
3467 if ((mii->mii_media_active & IFM_FDX) != 0 ||
3468 IFM_SUBTYPE(mii->mii_media_active) == IFM_LOOP)
3469 sc->sc_rxcfg |= RXCFG_ATX;
3470 else
3471 sc->sc_rxcfg &= ~RXCFG_ATX;
3472
3473 /*
3474 * Update CFG for MII/GMII.
3475 */
3476 if (sc->sc_ethercom.ec_if.if_baudrate == IF_Mbps(1000))
3477 cfg = sc->sc_cfg | CFG_MODE_1000;
3478 else
3479 cfg = sc->sc_cfg;
3480
3481 /*
3482 * 802.3x flow control.
3483 */
3484 pcr = 0;
3485 if (sc->sc_flowflags & IFM_FLOW) {
3486 if (sc->sc_flowflags & IFM_ETH_TXPAUSE)
3487 pcr |= sc->sc_rx_flow_thresh;
3488 if (sc->sc_flowflags & IFM_ETH_RXPAUSE)
3489 pcr |= PCR_PSEN | PCR_PS_MCAST;
3490 }
3491
3492 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_CFG, cfg);
3493 bus_space_write_4(sc->sc_st, sc->sc_sh, sc->sc_regs.r_txcfg,
3494 sc->sc_txcfg);
3495 bus_space_write_4(sc->sc_st, sc->sc_sh, sc->sc_regs.r_rxcfg,
3496 sc->sc_rxcfg);
3497 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_NS_PCR, pcr);
3498 }
3499
3500 /*
3501 * sip_mii_bitbang_read: [mii bit-bang interface function]
3502 *
3503 * Read the MII serial port for the MII bit-bang module.
3504 */
3505 static uint32_t
sipcom_mii_bitbang_read(device_t self)3506 sipcom_mii_bitbang_read(device_t self)
3507 {
3508 struct sip_softc *sc = device_private(self);
3509
3510 return (bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_EROMAR));
3511 }
3512
3513 /*
3514 * sip_mii_bitbang_write: [mii big-bang interface function]
3515 *
3516 * Write the MII serial port for the MII bit-bang module.
3517 */
3518 static void
sipcom_mii_bitbang_write(device_t self,uint32_t val)3519 sipcom_mii_bitbang_write(device_t self, uint32_t val)
3520 {
3521 struct sip_softc *sc = device_private(self);
3522
3523 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_EROMAR, val);
3524 }
3525
3526 /*
3527 * sip_sis900_mii_readreg: [mii interface function]
3528 *
3529 * Read a PHY register on the MII.
3530 */
3531 static int
sipcom_sis900_mii_readreg(device_t self,int phy,int reg,uint16_t * val)3532 sipcom_sis900_mii_readreg(device_t self, int phy, int reg, uint16_t *val)
3533 {
3534 struct sip_softc *sc = device_private(self);
3535 uint32_t enphy;
3536
3537 /*
3538 * The PHY of recent SiS chipsets is accessed through bitbang
3539 * operations.
3540 */
3541 if (sc->sc_model->sip_product == PCI_PRODUCT_SIS_900)
3542 return mii_bitbang_readreg(self, &sipcom_mii_bitbang_ops,
3543 phy, reg, val);
3544
3545 #ifndef SIS900_MII_RESTRICT
3546 /*
3547 * The SiS 900 has only an internal PHY on the MII. Only allow
3548 * MII address 0.
3549 */
3550 if (sc->sc_model->sip_product == PCI_PRODUCT_SIS_900 && phy != 0)
3551 return -1;
3552 #endif
3553
3554 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_ENPHY,
3555 (phy << ENPHY_PHYADDR_SHIFT) | (reg << ENPHY_REGADDR_SHIFT) |
3556 ENPHY_RWCMD | ENPHY_ACCESS);
3557 do {
3558 enphy = bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_ENPHY);
3559 } while (enphy & ENPHY_ACCESS);
3560
3561 *val = (enphy & ENPHY_PHYDATA) >> ENPHY_DATA_SHIFT;
3562 return 0;
3563 }
3564
3565 /*
3566 * sip_sis900_mii_writereg: [mii interface function]
3567 *
3568 * Write a PHY register on the MII.
3569 */
3570 static int
sipcom_sis900_mii_writereg(device_t self,int phy,int reg,uint16_t val)3571 sipcom_sis900_mii_writereg(device_t self, int phy, int reg, uint16_t val)
3572 {
3573 struct sip_softc *sc = device_private(self);
3574 uint32_t enphy;
3575
3576 if (sc->sc_model->sip_product == PCI_PRODUCT_SIS_900) {
3577 return mii_bitbang_writereg(self, &sipcom_mii_bitbang_ops,
3578 phy, reg, val);
3579 }
3580
3581 #ifndef SIS900_MII_RESTRICT
3582 /*
3583 * The SiS 900 has only an internal PHY on the MII. Only allow
3584 * MII address 0.
3585 */
3586 if (sc->sc_model->sip_product == PCI_PRODUCT_SIS_900 && phy != 0)
3587 return -1;
3588 #endif
3589
3590 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_ENPHY,
3591 (val << ENPHY_DATA_SHIFT) | (phy << ENPHY_PHYADDR_SHIFT) |
3592 (reg << ENPHY_REGADDR_SHIFT) | ENPHY_ACCESS);
3593 do {
3594 enphy = bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_ENPHY);
3595 } while (enphy & ENPHY_ACCESS);
3596
3597 return 0;
3598 }
3599
3600 /*
3601 * sip_sis900_mii_statchg: [mii interface function]
3602 *
3603 * Callback from MII layer when media changes.
3604 */
3605 static void
sipcom_sis900_mii_statchg(struct ifnet * ifp)3606 sipcom_sis900_mii_statchg(struct ifnet *ifp)
3607 {
3608 struct sip_softc *sc = ifp->if_softc;
3609 struct mii_data *mii = &sc->sc_mii;
3610 uint32_t flowctl;
3611
3612 /*
3613 * Get flow control negotiation result.
3614 */
3615 if (IFM_SUBTYPE(mii->mii_media.ifm_cur->ifm_media) == IFM_AUTO &&
3616 (mii->mii_media_active & IFM_ETH_FMASK) != sc->sc_flowflags) {
3617 sc->sc_flowflags = mii->mii_media_active & IFM_ETH_FMASK;
3618 mii->mii_media_active &= ~IFM_ETH_FMASK;
3619 }
3620
3621 /*
3622 * Update TXCFG for full-duplex operation.
3623 */
3624 if ((mii->mii_media_active & IFM_FDX) != 0)
3625 sc->sc_txcfg |= (TXCFG_CSI | TXCFG_HBI);
3626 else
3627 sc->sc_txcfg &= ~(TXCFG_CSI | TXCFG_HBI);
3628
3629 /*
3630 * Update RXCFG for full-duplex or loopback.
3631 */
3632 if ((mii->mii_media_active & IFM_FDX) != 0 ||
3633 IFM_SUBTYPE(mii->mii_media_active) == IFM_LOOP)
3634 sc->sc_rxcfg |= RXCFG_ATX;
3635 else
3636 sc->sc_rxcfg &= ~RXCFG_ATX;
3637
3638 /*
3639 * Update IMR for use of 802.3x flow control.
3640 */
3641 if (sc->sc_flowflags & IFM_FLOW) {
3642 sc->sc_imr |= (ISR_PAUSE_END | ISR_PAUSE_ST);
3643 flowctl = FLOWCTL_FLOWEN;
3644 } else {
3645 sc->sc_imr &= ~(ISR_PAUSE_END | ISR_PAUSE_ST);
3646 flowctl = 0;
3647 }
3648
3649 bus_space_write_4(sc->sc_st, sc->sc_sh, sc->sc_regs.r_txcfg,
3650 sc->sc_txcfg);
3651 bus_space_write_4(sc->sc_st, sc->sc_sh, sc->sc_regs.r_rxcfg,
3652 sc->sc_rxcfg);
3653 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_IMR, sc->sc_imr);
3654 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_FLOWCTL, flowctl);
3655 }
3656
3657 /*
3658 * sip_dp83815_mii_readreg: [mii interface function]
3659 *
3660 * Read a PHY register on the MII.
3661 */
3662 static int
sipcom_dp83815_mii_readreg(device_t self,int phy,int reg,uint16_t * val)3663 sipcom_dp83815_mii_readreg(device_t self, int phy, int reg, uint16_t *val)
3664 {
3665 struct sip_softc *sc = device_private(self);
3666 uint32_t data;
3667
3668 /*
3669 * The DP83815 only has an internal PHY. Only allow
3670 * MII address 0.
3671 */
3672 if (phy != 0)
3673 return -1;
3674
3675 /*
3676 * Apparently, after a reset, the DP83815 can take a while
3677 * to respond. During this recovery period, the BMSR returns
3678 * a value of 0. Catch this -- it's not supposed to happen
3679 * (the BMSR has some hardcoded-to-1 bits), and wait for the
3680 * PHY to come back to life.
3681 *
3682 * This works out because the BMSR is the first register
3683 * read during the PHY probe process.
3684 */
3685 do {
3686 data = bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_NS_PHY(reg));
3687 } while (reg == MII_BMSR && data == 0);
3688
3689 *val = data & 0xffff;
3690 return 0;
3691 }
3692
3693 /*
3694 * sip_dp83815_mii_writereg: [mii interface function]
3695 *
3696 * Write a PHY register to the MII.
3697 */
3698 static int
sipcom_dp83815_mii_writereg(device_t self,int phy,int reg,uint16_t val)3699 sipcom_dp83815_mii_writereg(device_t self, int phy, int reg, uint16_t val)
3700 {
3701 struct sip_softc *sc = device_private(self);
3702
3703 /*
3704 * The DP83815 only has an internal PHY. Only allow
3705 * MII address 0.
3706 */
3707 if (phy != 0)
3708 return -1;
3709
3710 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_NS_PHY(reg), val);
3711
3712 return 0;
3713 }
3714
3715 /*
3716 * sip_dp83815_mii_statchg: [mii interface function]
3717 *
3718 * Callback from MII layer when media changes.
3719 */
3720 static void
sipcom_dp83815_mii_statchg(struct ifnet * ifp)3721 sipcom_dp83815_mii_statchg(struct ifnet *ifp)
3722 {
3723 struct sip_softc *sc = ifp->if_softc;
3724
3725 /*
3726 * Update TXCFG for full-duplex operation.
3727 */
3728 if ((sc->sc_mii.mii_media_active & IFM_FDX) != 0)
3729 sc->sc_txcfg |= (TXCFG_CSI | TXCFG_HBI);
3730 else
3731 sc->sc_txcfg &= ~(TXCFG_CSI | TXCFG_HBI);
3732
3733 /*
3734 * Update RXCFG for full-duplex or loopback.
3735 */
3736 if ((sc->sc_mii.mii_media_active & IFM_FDX) != 0 ||
3737 IFM_SUBTYPE(sc->sc_mii.mii_media_active) == IFM_LOOP)
3738 sc->sc_rxcfg |= RXCFG_ATX;
3739 else
3740 sc->sc_rxcfg &= ~RXCFG_ATX;
3741
3742 /*
3743 * XXX 802.3x flow control.
3744 */
3745
3746 bus_space_write_4(sc->sc_st, sc->sc_sh, sc->sc_regs.r_txcfg,
3747 sc->sc_txcfg);
3748 bus_space_write_4(sc->sc_st, sc->sc_sh, sc->sc_regs.r_rxcfg,
3749 sc->sc_rxcfg);
3750
3751 /*
3752 * Some DP83815s experience problems when used with short
3753 * (< 30m/100ft) Ethernet cables in 100BaseTX mode. This
3754 * sequence adjusts the DSP's signal attenuation to fix the
3755 * problem.
3756 */
3757 if (IFM_SUBTYPE(sc->sc_mii.mii_media_active) == IFM_100_TX) {
3758 uint32_t reg;
3759
3760 bus_space_write_4(sc->sc_st, sc->sc_sh, 0x00cc, 0x0001);
3761
3762 reg = bus_space_read_4(sc->sc_st, sc->sc_sh, 0x00f4);
3763 reg &= 0x0fff;
3764 bus_space_write_4(sc->sc_st, sc->sc_sh, 0x00f4, reg | 0x1000);
3765 delay(100);
3766 reg = bus_space_read_4(sc->sc_st, sc->sc_sh, 0x00fc);
3767 reg &= 0x00ff;
3768 if ((reg & 0x0080) == 0 || (reg >= 0x00d8)) {
3769 bus_space_write_4(sc->sc_st, sc->sc_sh, 0x00fc,
3770 0x00e8);
3771 reg = bus_space_read_4(sc->sc_st, sc->sc_sh, 0x00f4);
3772 bus_space_write_4(sc->sc_st, sc->sc_sh, 0x00f4,
3773 reg | 0x20);
3774 }
3775
3776 bus_space_write_4(sc->sc_st, sc->sc_sh, 0x00cc, 0);
3777 }
3778 }
3779
3780 static void
sipcom_dp83820_read_macaddr(struct sip_softc * sc,const struct pci_attach_args * pa,uint8_t * enaddr)3781 sipcom_dp83820_read_macaddr(struct sip_softc *sc,
3782 const struct pci_attach_args *pa, uint8_t *enaddr)
3783 {
3784 uint16_t eeprom_data[SIP_DP83820_EEPROM_LENGTH / 2];
3785 uint8_t cksum, *e, match;
3786 int i;
3787
3788 /*
3789 * EEPROM data format for the DP83820 can be found in
3790 * the DP83820 manual, section 4.2.4.
3791 */
3792
3793 sipcom_read_eeprom(sc, 0, __arraycount(eeprom_data), eeprom_data);
3794
3795 match = eeprom_data[SIP_DP83820_EEPROM_CHECKSUM / 2] >> 8;
3796 match = ~(match - 1);
3797
3798 cksum = 0x55;
3799 e = (uint8_t *)eeprom_data;
3800 for (i = 0; i < SIP_DP83820_EEPROM_CHECKSUM; i++)
3801 cksum += *e++;
3802
3803 if (cksum != match)
3804 printf("%s: Checksum (%x) mismatch (%x)",
3805 device_xname(sc->sc_dev), cksum, match);
3806
3807 enaddr[0] = eeprom_data[SIP_DP83820_EEPROM_PMATCH2 / 2] & 0xff;
3808 enaddr[1] = eeprom_data[SIP_DP83820_EEPROM_PMATCH2 / 2] >> 8;
3809 enaddr[2] = eeprom_data[SIP_DP83820_EEPROM_PMATCH1 / 2] & 0xff;
3810 enaddr[3] = eeprom_data[SIP_DP83820_EEPROM_PMATCH1 / 2] >> 8;
3811 enaddr[4] = eeprom_data[SIP_DP83820_EEPROM_PMATCH0 / 2] & 0xff;
3812 enaddr[5] = eeprom_data[SIP_DP83820_EEPROM_PMATCH0 / 2] >> 8;
3813 }
3814
3815 static void
sipcom_sis900_eeprom_delay(struct sip_softc * sc)3816 sipcom_sis900_eeprom_delay(struct sip_softc *sc)
3817 {
3818 int i;
3819
3820 /*
3821 * FreeBSD goes from (300/33)+1 [10] to 0. There must be
3822 * a reason, but I don't know it.
3823 */
3824 for (i = 0; i < 10; i++)
3825 bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_CR);
3826 }
3827
3828 static void
sipcom_sis900_read_macaddr(struct sip_softc * sc,const struct pci_attach_args * pa,uint8_t * enaddr)3829 sipcom_sis900_read_macaddr(struct sip_softc *sc,
3830 const struct pci_attach_args *pa, uint8_t *enaddr)
3831 {
3832 uint16_t myea[ETHER_ADDR_LEN / 2];
3833
3834 switch (sc->sc_rev) {
3835 case SIS_REV_630S:
3836 case SIS_REV_630E:
3837 case SIS_REV_630EA1:
3838 case SIS_REV_630ET:
3839 case SIS_REV_635:
3840 /*
3841 * The MAC address for the on-board Ethernet of
3842 * the SiS 630 chipset is in the NVRAM. Kick
3843 * the chip into re-loading it from NVRAM, and
3844 * read the MAC address out of the filter registers.
3845 */
3846 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_CR, CR_RLD);
3847
3848 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_RFCR,
3849 RFCR_RFADDR_NODE0);
3850 myea[0] = bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_RFDR) &
3851 0xffff;
3852
3853 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_RFCR,
3854 RFCR_RFADDR_NODE2);
3855 myea[1] = bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_RFDR) &
3856 0xffff;
3857
3858 bus_space_write_4(sc->sc_st, sc->sc_sh, SIP_RFCR,
3859 RFCR_RFADDR_NODE4);
3860 myea[2] = bus_space_read_4(sc->sc_st, sc->sc_sh, SIP_RFDR) &
3861 0xffff;
3862 break;
3863
3864 case SIS_REV_960:
3865 {
3866 #define SIS_SET_EROMAR(x, y) \
3867 bus_space_write_4(x->sc_st, x->sc_sh, SIP_EROMAR, \
3868 bus_space_read_4(x->sc_st, x->sc_sh, SIP_EROMAR) | (y))
3869
3870 #define SIS_CLR_EROMAR(x, y) \
3871 bus_space_write_4(x->sc_st, x->sc_sh, SIP_EROMAR, \
3872 bus_space_read_4(x->sc_st, x->sc_sh, SIP_EROMAR) & ~(y))
3873
3874 int waittime, i;
3875
3876 /* Allow to read EEPROM from LAN. It is shared
3877 * between a 1394 controller and the NIC and each
3878 * time we access it, we need to set SIS_EECMD_REQ.
3879 */
3880 SIS_SET_EROMAR(sc, EROMAR_REQ);
3881
3882 for (waittime = 0; waittime < 1000; waittime++) { /* 1 ms max */
3883 /* Force EEPROM to idle state. */
3884
3885 /*
3886 * XXX-cube This is ugly.
3887 * I'll look for docs about it.
3888 */
3889 SIS_SET_EROMAR(sc, EROMAR_EECS);
3890 sipcom_sis900_eeprom_delay(sc);
3891 for (i = 0; i <= 25; i++) { /* Yes, 26 times. */
3892 SIS_SET_EROMAR(sc, EROMAR_EESK);
3893 sipcom_sis900_eeprom_delay(sc);
3894 SIS_CLR_EROMAR(sc, EROMAR_EESK);
3895 sipcom_sis900_eeprom_delay(sc);
3896 }
3897 SIS_CLR_EROMAR(sc, EROMAR_EECS);
3898 sipcom_sis900_eeprom_delay(sc);
3899 bus_space_write_4(sc->sc_st, sc->sc_sh,
3900 SIP_EROMAR, 0);
3901
3902 if (bus_space_read_4(sc->sc_st, sc->sc_sh,
3903 SIP_EROMAR) & EROMAR_GNT) {
3904 sipcom_read_eeprom(sc,
3905 SIP_EEPROM_ETHERNET_ID0 >> 1,
3906 sizeof(myea) / sizeof(myea[0]),
3907 myea);
3908 break;
3909 }
3910 DELAY(1);
3911 }
3912
3913 /*
3914 * Set SIS_EECTL_CLK to high, so a other master
3915 * can operate on the i2c bus.
3916 */
3917 SIS_SET_EROMAR(sc, EROMAR_EESK);
3918
3919 /* Refuse EEPROM access by LAN */
3920 SIS_SET_EROMAR(sc, EROMAR_DONE);
3921 } break;
3922
3923 default:
3924 sipcom_read_eeprom(sc, SIP_EEPROM_ETHERNET_ID0 >> 1,
3925 sizeof(myea) / sizeof(myea[0]), myea);
3926 }
3927
3928 enaddr[0] = myea[0] & 0xff;
3929 enaddr[1] = myea[0] >> 8;
3930 enaddr[2] = myea[1] & 0xff;
3931 enaddr[3] = myea[1] >> 8;
3932 enaddr[4] = myea[2] & 0xff;
3933 enaddr[5] = myea[2] >> 8;
3934 }
3935
3936 /* Table and macro to bit-reverse an octet. */
3937 static const uint8_t bbr4[] = {0,8,4,12,2,10,6,14,1,9,5,13,3,11,7,15};
3938 #define bbr(v) ((bbr4[(v)&0xf] << 4) | bbr4[((v)>>4) & 0xf])
3939
3940 static void
sipcom_dp83815_read_macaddr(struct sip_softc * sc,const struct pci_attach_args * pa,uint8_t * enaddr)3941 sipcom_dp83815_read_macaddr(struct sip_softc *sc,
3942 const struct pci_attach_args *pa, uint8_t *enaddr)
3943 {
3944 uint16_t eeprom_data[SIP_DP83815_EEPROM_LENGTH / 2], *ea;
3945 uint8_t cksum, *e, match;
3946 int i;
3947
3948 sipcom_read_eeprom(sc, 0, sizeof(eeprom_data) /
3949 sizeof(eeprom_data[0]), eeprom_data);
3950
3951 match = eeprom_data[SIP_DP83815_EEPROM_CHECKSUM/2] >> 8;
3952 match = ~(match - 1);
3953
3954 cksum = 0x55;
3955 e = (uint8_t *)eeprom_data;
3956 for (i = 0; i < SIP_DP83815_EEPROM_CHECKSUM; i++)
3957 cksum += *e++;
3958
3959 if (cksum != match)
3960 printf("%s: Checksum (%x) mismatch (%x)",
3961 device_xname(sc->sc_dev), cksum, match);
3962
3963 /*
3964 * Unrolled because it makes slightly more sense this way.
3965 * The DP83815 stores the MAC address in bit 0 of word 6
3966 * through bit 15 of word 8.
3967 */
3968 ea = &eeprom_data[6];
3969 enaddr[0] = ((*ea & 0x1) << 7);
3970 ea++;
3971 enaddr[0] |= ((*ea & 0xFE00) >> 9);
3972 enaddr[1] = ((*ea & 0x1FE) >> 1);
3973 enaddr[2] = ((*ea & 0x1) << 7);
3974 ea++;
3975 enaddr[2] |= ((*ea & 0xFE00) >> 9);
3976 enaddr[3] = ((*ea & 0x1FE) >> 1);
3977 enaddr[4] = ((*ea & 0x1) << 7);
3978 ea++;
3979 enaddr[4] |= ((*ea & 0xFE00) >> 9);
3980 enaddr[5] = ((*ea & 0x1FE) >> 1);
3981
3982 /*
3983 * In case that's not weird enough, we also need to reverse
3984 * the bits in each byte. This all actually makes more sense
3985 * if you think about the EEPROM storage as an array of bits
3986 * being shifted into bytes, but that's not how we're looking
3987 * at it here...
3988 */
3989 for (i = 0; i < 6 ;i++)
3990 enaddr[i] = bbr(enaddr[i]);
3991 }
3992
3993 /*
3994 * sip_mediastatus: [ifmedia interface function]
3995 *
3996 * Get the current interface media status.
3997 */
3998 static void
sipcom_mediastatus(struct ifnet * ifp,struct ifmediareq * ifmr)3999 sipcom_mediastatus(struct ifnet *ifp, struct ifmediareq *ifmr)
4000 {
4001 struct sip_softc *sc = ifp->if_softc;
4002
4003 if (!device_is_active(sc->sc_dev)) {
4004 ifmr->ifm_active = IFM_ETHER | IFM_NONE;
4005 ifmr->ifm_status = 0;
4006 return;
4007 }
4008 ether_mediastatus(ifp, ifmr);
4009 ifmr->ifm_active = (ifmr->ifm_active & ~IFM_ETH_FMASK) |
4010 sc->sc_flowflags;
4011 }
4012