xref: /freebsd/contrib/wpa/src/drivers/driver.h (revision a90b9d01)

/*
 * Driver interface definition
 * Copyright (c) 2003-2017, Jouni Malinen <j@w1.fi>
 *
 * This software may be distributed under the terms of the BSD license.
 * See README for more details.
 *
 * This file defines a driver interface used by both %wpa_supplicant and
 * hostapd. The first part of the file defines data structures used in various
 * driver operations. This is followed by the struct wpa_driver_ops that each
 * driver wrapper will beed to define with callback functions for requesting
 * driver operations. After this, there are definitions for driver event
 * reporting with wpa_supplicant_event() and some convenience helper functions
 * that can be used to report events.
 */

#ifndef DRIVER_H
#define DRIVER_H

#define WPA_SUPPLICANT_DRIVER_VERSION 4

#include "common/defs.h"
#include "common/ieee802_11_defs.h"
#include "common/wpa_common.h"
#ifdef CONFIG_MACSEC
#include "pae/ieee802_1x_kay.h"
#endif /* CONFIG_MACSEC */
#include "utils/list.h"

#define HOSTAPD_CHAN_DISABLED 0x00000001
#define HOSTAPD_CHAN_NO_IR 0x00000002
#define HOSTAPD_CHAN_RADAR 0x00000008
#define HOSTAPD_CHAN_HT40PLUS 0x00000010
#define HOSTAPD_CHAN_HT40MINUS 0x00000020
#define HOSTAPD_CHAN_HT40 0x00000040
#define HOSTAPD_CHAN_SURVEY_LIST_INITIALIZED 0x00000080

#define HOSTAPD_CHAN_DFS_UNKNOWN 0x00000000
#define HOSTAPD_CHAN_DFS_USABLE 0x00000100
#define HOSTAPD_CHAN_DFS_UNAVAILABLE 0x00000200
#define HOSTAPD_CHAN_DFS_AVAILABLE 0x00000300
#define HOSTAPD_CHAN_DFS_MASK 0x00000300

#define HOSTAPD_CHAN_VHT_80MHZ_SUBCHANNEL 0x00000800
#define HOSTAPD_CHAN_VHT_160MHZ_SUBCHANNEL 0x00001000
#define HOSTAPD_CHAN_EHT_320MHZ_SUBCHANNEL 0x00002000

#define HOSTAPD_CHAN_INDOOR_ONLY 0x00010000
#define HOSTAPD_CHAN_GO_CONCURRENT 0x00020000

/* Allowed bandwidth mask */
enum hostapd_chan_width_attr {
	HOSTAPD_CHAN_WIDTH_10   = BIT(0),
	HOSTAPD_CHAN_WIDTH_20   = BIT(1),
	HOSTAPD_CHAN_WIDTH_40P  = BIT(2),
	HOSTAPD_CHAN_WIDTH_40M  = BIT(3),
	HOSTAPD_CHAN_WIDTH_80   = BIT(4),
	HOSTAPD_CHAN_WIDTH_160  = BIT(5),
	HOSTAPD_CHAN_WIDTH_320  = BIT(6),
};

/* Filter gratuitous ARP */
#define WPA_DATA_FRAME_FILTER_FLAG_ARP BIT(0)
/* Filter unsolicited Neighbor Advertisement */
#define WPA_DATA_FRAME_FILTER_FLAG_NA BIT(1)
/* Filter unicast IP packets encrypted using the GTK */
#define WPA_DATA_FRAME_FILTER_FLAG_GTK BIT(2)

#define HOSTAPD_DFS_REGION_FCC	1
#define HOSTAPD_DFS_REGION_ETSI	2
#define HOSTAPD_DFS_REGION_JP	3

/**
 * enum reg_change_initiator - Regulatory change initiator
 */
enum reg_change_initiator {
	REGDOM_SET_BY_CORE,
	REGDOM_SET_BY_USER,
	REGDOM_SET_BY_DRIVER,
	REGDOM_SET_BY_COUNTRY_IE,
	REGDOM_BEACON_HINT,
};

/**
 * enum reg_type - Regulatory change types
 */
enum reg_type {
	REGDOM_TYPE_UNKNOWN,
	REGDOM_TYPE_COUNTRY,
	REGDOM_TYPE_WORLD,
	REGDOM_TYPE_CUSTOM_WORLD,
	REGDOM_TYPE_INTERSECTION,
};

/**
 * struct hostapd_wmm_rule - WMM regulatory rule
 * @min_cwmin: Lower bound of CW_min value
 * @min_cwmax: Lower bound of CW_max value
 * @min_aifs: Lower bound of AIFS value
 * @max_txop: Upper bound of TXOP, value in units of 32 usec
 */
struct hostapd_wmm_rule {
	int min_cwmin;
	int min_cwmax;
	int min_aifs;
	int max_txop;
};

/**
 * struct hostapd_channel_data - Channel information
 */
struct hostapd_channel_data {
	/**
	 * chan - Channel number (IEEE 802.11)
	 */
	short chan;

	/**
	 * freq - Frequency in MHz
	 */
	int freq;

	/**
	 * flag - Channel flags (HOSTAPD_CHAN_*)
	 */
	int flag;

	/**
	 * allowed_bw - Allowed channel width bitmask
	 *
	 * See enum hostapd_chan_width_attr.
	 */
	u32 allowed_bw;

	/**
	 * max_tx_power - Regulatory transmit power limit in dBm
	 */
	u8 max_tx_power;

	/**
	 * survey_list - Linked list of surveys (struct freq_survey)
	 */
	struct dl_list survey_list;

	/**
	 * min_nf - Minimum observed noise floor, in dBm, based on all
	 * surveyed channel data
	 */
	s8 min_nf;

#ifdef CONFIG_ACS
	/**
	 * interference_factor - Computed interference factor on this
	 * channel (used internally in src/ap/acs.c; driver wrappers do not
	 * need to set this)
	 */
	long double interference_factor;
#endif /* CONFIG_ACS */

	/**
	 * dfs_cac_ms - DFS CAC time in milliseconds
	 */
	unsigned int dfs_cac_ms;

	/**
	 * wmm_rules_valid - Indicates wmm_rules state
	 */
	int wmm_rules_valid;

	/**
	 * wmm_rules - WMM regulatory rules
	 */
	struct hostapd_wmm_rule wmm_rules[WMM_AC_NUM];

	/**
	 * punct_bitmap - RU puncturing bitmap
	 */
	u16 punct_bitmap;
};

#define HE_MAC_CAPAB_0		0
#define HE_MAX_MAC_CAPAB_SIZE	6
#define HE_MAX_PHY_CAPAB_SIZE	11
#define HE_MAX_MCS_CAPAB_SIZE	12
#define HE_MAX_PPET_CAPAB_SIZE	25

/**
 * struct he_capabilities - IEEE 802.11ax HE capabilities
 */
struct he_capabilities {
	u8 he_supported;
	u8 phy_cap[HE_MAX_PHY_CAPAB_SIZE];
	u8 mac_cap[HE_MAX_MAC_CAPAB_SIZE];
	u8 mcs[HE_MAX_MCS_CAPAB_SIZE];
	u8 ppet[HE_MAX_PPET_CAPAB_SIZE];
	u16 he_6ghz_capa;
};

/* struct eht_capabilities - IEEE 802.11be EHT capabilities */
struct eht_capabilities {
	bool eht_supported;
	u16 mac_cap;
	u8 phy_cap[EHT_PHY_CAPAB_LEN];
	u8 mcs[EHT_MCS_NSS_CAPAB_LEN];
	u8 ppet[EHT_PPE_THRESH_CAPAB_LEN];
};

#define HOSTAPD_MODE_FLAG_HT_INFO_KNOWN BIT(0)
#define HOSTAPD_MODE_FLAG_VHT_INFO_KNOWN BIT(1)
#define HOSTAPD_MODE_FLAG_HE_INFO_KNOWN BIT(2)


enum ieee80211_op_mode {
	IEEE80211_MODE_INFRA = 0,
	IEEE80211_MODE_IBSS = 1,
	IEEE80211_MODE_AP = 2,
	IEEE80211_MODE_MESH = 5,

	/* only add new entries before IEEE80211_MODE_NUM */
	IEEE80211_MODE_NUM
};

/**
 * struct ieee80211_edmg_config - EDMG configuration
 *
 * This structure describes most essential parameters needed
 * for IEEE 802.11ay EDMG configuration
 *
 * @channels: Bitmap that indicates the 2.16 GHz channel(s)
 *	that are allowed to be used for transmissions.
 *	Bit 0 indicates channel 1, bit 1 indicates channel 2, etc.
 *	Set to 0 to indicate EDMG not supported.
 * @bw_config: Channel BW Configuration subfield encodes
 *	the allowed channel bandwidth configurations
 */
struct ieee80211_edmg_config {
	u8 channels;
	enum edmg_bw_config bw_config;
};

/**
 * struct hostapd_hw_modes - Supported hardware mode information
 */
struct hostapd_hw_modes {
	/**
	 * mode - Hardware mode
	 */
	enum hostapd_hw_mode mode;

	/**
	 * is_6ghz - Whether the mode information is for the 6 GHz band
	 */
	bool is_6ghz;

	/**
	 * num_channels - Number of entries in the channels array
	 */
	int num_channels;

	/**
	 * channels - Array of supported channels
	 */
	struct hostapd_channel_data *channels;

	/**
	 * num_rates - Number of entries in the rates array
	 */
	int num_rates;

	/**
	 * rates - Array of supported rates in 100 kbps units
	 */
	int *rates;

	/**
	 * ht_capab - HT (IEEE 802.11n) capabilities
	 */
	u16 ht_capab;

	/**
	 * mcs_set - MCS (IEEE 802.11n) rate parameters
	 */
	u8 mcs_set[16];

	/**
	 * a_mpdu_params - A-MPDU (IEEE 802.11n) parameters
	 */
	u8 a_mpdu_params;

	/**
	 * vht_capab - VHT (IEEE 802.11ac) capabilities
	 */
	u32 vht_capab;

	/**
	 * vht_mcs_set - VHT MCS (IEEE 802.11ac) rate parameters
	 */
	u8 vht_mcs_set[8];

	unsigned int flags; /* HOSTAPD_MODE_FLAG_* */

	/**
	 * he_capab - HE (IEEE 802.11ax) capabilities
	 */
	struct he_capabilities he_capab[IEEE80211_MODE_NUM];

	/**
	 * This structure describes the most essential parameters needed
	 * for IEEE 802.11ay EDMG configuration.
	 */
	struct ieee80211_edmg_config edmg;

	/**
	 * eht_capab - EHT (IEEE 802.11be) capabilities
	 */
	struct eht_capabilities eht_capab[IEEE80211_MODE_NUM];
};


#define IEEE80211_CAP_ESS	0x0001
#define IEEE80211_CAP_IBSS	0x0002
#define IEEE80211_CAP_PRIVACY	0x0010
#define IEEE80211_CAP_RRM	0x1000

/* DMG (60 GHz) IEEE 802.11ad */
/* type - bits 0..1 */
#define IEEE80211_CAP_DMG_MASK	0x0003
#define IEEE80211_CAP_DMG_IBSS	0x0001 /* Tx by: STA */
#define IEEE80211_CAP_DMG_PBSS	0x0002 /* Tx by: PCP */
#define IEEE80211_CAP_DMG_AP	0x0003 /* Tx by: AP */

#define WPA_SCAN_QUAL_INVALID		BIT(0)
#define WPA_SCAN_NOISE_INVALID		BIT(1)
#define WPA_SCAN_LEVEL_INVALID		BIT(2)
#define WPA_SCAN_LEVEL_DBM		BIT(3)
#define WPA_SCAN_ASSOCIATED		BIT(5)

/**
 * struct wpa_scan_res - Scan result for an BSS/IBSS
 * @flags: information flags about the BSS/IBSS (WPA_SCAN_*)
 * @bssid: BSSID
 * @freq: frequency of the channel in MHz (e.g., 2412 = channel 1)
 * @max_cw: the max channel width of the connection (calculated during scan
 * result processing)
 * @beacon_int: beacon interval in TUs (host byte order)
 * @caps: capability information field in host byte order
 * @qual: signal quality
 * @noise: noise level
 * @level: signal level
 * @tsf: Timestamp
 * @age: Age of the information in milliseconds (i.e., how many milliseconds
 * ago the last Beacon or Probe Response frame was received)
 * @est_throughput: Estimated throughput in kbps (this is calculated during
 * scan result processing if left zero by the driver wrapper)
 * @snr: Signal-to-noise ratio in dB (calculated during scan result processing)
 * @parent_tsf: Time when the Beacon/Probe Response frame was received in terms
 * of TSF of the BSS specified by %tsf_bssid.
 * @tsf_bssid: The BSS that %parent_tsf TSF time refers to.
 * @beacon_newer: Whether the Beacon frame data is known to be newer
 * @ie_len: length of the following IE field in octets
 * @beacon_ie_len: length of the following Beacon IE field in octets
 *
 * This structure is used as a generic format for scan results from the
 * driver. Each driver interface implementation is responsible for converting
 * the driver or OS specific scan results into this format.
 *
 * If the driver does not support reporting all IEs, the IE data structure is
 * constructed of the IEs that are available. This field will also need to
 * include SSID in IE format. All drivers are encouraged to be extended to
 * report all IEs to make it easier to support future additions.
 *
 * This structure data is followed by ie_len octets of IEs from Probe Response
 * frame (or if the driver does not indicate source of IEs, these may also be
 * from Beacon frame). After the first set of IEs, another set of IEs may follow
 * (with beacon_ie_len octets of data) if the driver provides both IE sets.
 */
struct wpa_scan_res {
	unsigned int flags;
	u8 bssid[ETH_ALEN];
	int freq;
	enum chan_width max_cw;
	u16 beacon_int;
	u16 caps;
	int qual;
	int noise;
	int level;
	u64 tsf;
	unsigned int age;
	unsigned int est_throughput;
	int snr;
	u64 parent_tsf;
	u8 tsf_bssid[ETH_ALEN];
	bool beacon_newer;
	size_t ie_len;
	size_t beacon_ie_len;
	/* Followed by ie_len + beacon_ie_len octets of IE data */
};

/**
 * struct wpa_scan_results - Scan results
 * @res: Array of pointers to allocated variable length scan result entries
 * @num: Number of entries in the scan result array
 * @fetch_time: Time when the results were fetched from the driver
 */
struct wpa_scan_results {
	struct wpa_scan_res **res;
	size_t num;
	struct os_reltime fetch_time;
};

/**
 * struct wpa_interface_info - Network interface information
 * @next: Pointer to the next interface or NULL if this is the last one
 * @ifname: Interface name that can be used with init() or init2()
 * @desc: Human readable adapter description (e.g., vendor/model) or NULL if
 *	not available
 * @drv_name: struct wpa_driver_ops::name (note: unlike other strings, this one
 *	is not an allocated copy, i.e., get_interfaces() caller will not free
 *	this)
 */
struct wpa_interface_info {
	struct wpa_interface_info *next;
	char *ifname;
	char *desc;
	const char *drv_name;
};

#define WPAS_MAX_SCAN_SSIDS 16

/**
 * struct wpa_driver_scan_ssid - SSIDs to scan for
 * @ssid - specific SSID to scan for (ProbeReq)
 *	%NULL or zero-length SSID is used to indicate active scan
 *	with wildcard SSID.
 * @ssid_len - Length of the SSID in octets
 */
struct wpa_driver_scan_ssid {
	const u8 *ssid;
	size_t ssid_len;
};

struct t2lm_mapping {
	/**
	 * downlink - Bitmap of TIDs mapped with a link in downlink direction
	 */
	u8 downlink;

	/**
	 * uplink - Bitmap of TIDs mapped with a link in uplink direction
	 */
	u8 uplink;
};

/**
 * struct wpa_driver_scan_params - Scan parameters
 * Data for struct wpa_driver_ops::scan2().
 */
struct wpa_driver_scan_params {
	/**
	 * ssids - SSIDs to scan for
	 */
	struct wpa_driver_scan_ssid ssids[WPAS_MAX_SCAN_SSIDS];

	/**
	 * num_ssids - Number of entries in ssids array
	 * Zero indicates a request for a passive scan.
	 */
	size_t num_ssids;

	/**
	 * extra_ies - Extra IE(s) to add into Probe Request or %NULL
	 */
	const u8 *extra_ies;

	/**
	 * extra_ies_len - Length of extra_ies in octets
	 */
	size_t extra_ies_len;

	/**
	 * freqs - Array of frequencies to scan or %NULL for all frequencies
	 *
	 * The frequency is set in MHz. The array is zero-terminated.
	 */
	int *freqs;

	/**
	 * filter_ssids - Filter for reporting SSIDs
	 *
	 * This optional parameter can be used to request the driver wrapper to
	 * filter scan results to include only the specified SSIDs. %NULL
	 * indicates that no filtering is to be done. This can be used to
	 * reduce memory needs for scan results in environments that have large
	 * number of APs with different SSIDs.
	 *
	 * The driver wrapper is allowed to take this allocated buffer into its
	 * own use by setting the pointer to %NULL. In that case, the driver
	 * wrapper is responsible for freeing the buffer with os_free() once it
	 * is not needed anymore.
	 */
	struct wpa_driver_scan_filter {
		u8 ssid[SSID_MAX_LEN];
		size_t ssid_len;
	} *filter_ssids;

	/**
	 * num_filter_ssids - Number of entries in filter_ssids array
	 */
	size_t num_filter_ssids;

	/**
	 * filter_rssi - Filter by RSSI
	 *
	 * The driver may filter scan results in firmware to reduce host
	 * wakeups and thereby save power. Specify the RSSI threshold in s32
	 * dBm.
	 */
	s32 filter_rssi;

	/**
	 * p2p_probe - Used to disable CCK (802.11b) rates for P2P probes
	 *
	 * When set, the driver is expected to remove rates 1, 2, 5.5, and 11
	 * Mbps from the support rates element(s) in the Probe Request frames
	 * and not to transmit the frames at any of those rates.
	 */
	unsigned int p2p_probe:1;

	/**
	 * only_new_results - Request driver to report only new results
	 *
	 * This is used to request the driver to report only BSSes that have
	 * been detected after this scan request has been started, i.e., to
	 * flush old cached BSS entries.
	 */
	unsigned int only_new_results:1;

	/**
	 * low_priority - Requests driver to use a lower scan priority
	 *
	 * This is used to request the driver to use a lower scan priority
	 * if it supports such a thing.
	 */
	unsigned int low_priority:1;

	/**
	 * mac_addr_rand - Requests driver to randomize MAC address
	 */
	unsigned int mac_addr_rand:1;

	/**
	 * mac_addr - MAC address used with randomization. The address cannot be
	 * a multicast one, i.e., bit 0 of byte 0 should not be set.
	 */
	u8 *mac_addr;

	/**
	 * mac_addr_mask - MAC address mask used with randomization.
	 *
	 * Bits that are 0 in the mask should be randomized. Bits that are 1 in
	 * the mask should be taken as is from mac_addr. The mask should not
	 * allow the generation of a multicast address, i.e., bit 0 of byte 0
	 * must be set.
	 */
	const u8 *mac_addr_mask;

	/**
	 * sched_scan_plans - Scan plans for scheduled scan
	 *
	 * Each scan plan consists of the number of iterations to scan and the
	 * interval between scans. When a scan plan finishes (i.e., it was run
	 * for the specified number of iterations), the next scan plan is
	 * executed. The scan plans are executed in the order they appear in
	 * the array (lower index first). The last scan plan will run infinitely
	 * (until requested to stop), thus must not specify the number of
	 * iterations. All other scan plans must specify the number of
	 * iterations.
	 */
	struct sched_scan_plan {
		 u32 interval; /* In seconds */
		 u32 iterations; /* Zero to run infinitely */
	 } *sched_scan_plans;

	/**
	 * sched_scan_plans_num - Number of scan plans in sched_scan_plans array
	 */
	 unsigned int sched_scan_plans_num;

	/**
	 * sched_scan_start_delay - Delay to use before starting the first scan
	 *
	 * Delay (in seconds) before scheduling first scan plan cycle. The
	 * driver may ignore this parameter and start immediately (or at any
	 * other time), if this feature is not supported.
	 */
	 u32 sched_scan_start_delay;

	/**
	 * bssid - Specific BSSID to scan for
	 *
	 * This optional parameter can be used to replace the default wildcard
	 * BSSID with a specific BSSID to scan for if results are needed from
	 * only a single BSS.
	 */
	const u8 *bssid;

	/**
	 * scan_cookie - Unique identification representing the scan request
	 *
	 * This scan_cookie carries a unique identification representing the
	 * scan request if the host driver/kernel supports concurrent scan
	 * requests. This cookie is returned from the corresponding driver
	 * interface.
	 *
	 * Note: Unlike other parameters in this structure, scan_cookie is used
	 * only to return information instead of setting parameters for the
	 * scan.
	 */
	u64 scan_cookie;

	 /**
	  * duration - Dwell time on each channel
	  *
	  * This optional parameter can be used to set the dwell time on each
	  * channel. In TUs.
	  */
	 u16 duration;

	 /**
	  * duration_mandatory - Whether the specified duration is mandatory
	  *
	  * If this is set, the duration specified by the %duration field is
	  * mandatory (and the driver should reject the scan request if it is
	  * unable to comply with the specified duration), otherwise it is the
	  * maximum duration and the actual duration may be shorter.
	  */
	 unsigned int duration_mandatory:1;

	/**
	 * relative_rssi_set - Whether relative RSSI parameters are set
	 */
	unsigned int relative_rssi_set:1;

	/**
	 * relative_rssi - Relative RSSI for reporting better BSSs
	 *
	 * Amount of RSSI by which a BSS should be better than the current
	 * connected BSS to report the new BSS to user space.
	 */
	s8 relative_rssi;

	/**
	 * relative_adjust_band - Band to which RSSI should be adjusted
	 *
	 * The relative_adjust_rssi should be added to the band specified
	 * by relative_adjust_band.
	 */
	enum set_band relative_adjust_band;

	/**
	 * relative_adjust_rssi - RSSI to be added to relative_adjust_band
	 *
	 * An amount of relative_band_rssi should be added to the BSSs that
	 * belong to the band specified by relative_adjust_band while comparing
	 * with other bands for BSS reporting.
	 */
	s8 relative_adjust_rssi;

	/**
	 * oce_scan
	 *
	 * Enable the following OCE scan features: (WFA OCE TechSpec v1.0)
	 * - Accept broadcast Probe Response frame.
	 * - Probe Request frame deferral and suppression.
	 * - Max Channel Time - driver fills FILS request params IE with
	 *   Maximum Channel Time.
	 * - Send 1st Probe Request frame in rate of minimum 5.5 Mbps.
	 */
	unsigned int oce_scan:1;

	/**
	 * p2p_include_6ghz - Include 6 GHz channels for P2P full scan
	 *
	 */
	unsigned int p2p_include_6ghz:1;

	/**
	 * non_coloc_6ghz - Force scanning of non-PSC 6 GHz channels
	 *
	 * If this is set, the driver should scan non-PSC channels from the
	 * scan request even if neighbor reports from 2.4/5 GHz APs did not
	 * report a co-located AP on these channels. The default is to scan
	 * non-PSC channels only if a co-located AP was reported on the channel.
	 */
	unsigned int non_coloc_6ghz:1;

	/**
	 * min_probe_req_content - Minimize probe request content to only have
	 * minimal requirement elements, e.g., supported rates etc., and no
	 * additional elements other then those provided by user space.
	 */
	unsigned int min_probe_req_content:1;

	/**
	 * link_id - Specify the link that is requesting the scan on an MLD
	 *
	 * This is set when operating as an AP MLD and doing an OBSS scan.
	 * -1 indicates that no particular link ID is set.
	 */
	s8 link_id;

	/*
	 * NOTE: Whenever adding new parameters here, please make sure
	 * wpa_scan_clone_params() and wpa_scan_free_params() get updated with
	 * matching changes.
	 */
};

/**
 * struct wpa_driver_auth_params - Authentication parameters
 * Data for struct wpa_driver_ops::authenticate().
 */
struct wpa_driver_auth_params {
	int freq;
	const u8 *bssid;
	const u8 *ssid;
	size_t ssid_len;
	int auth_alg;
	const u8 *ie;
	size_t ie_len;
	const u8 *wep_key[4];
	size_t wep_key_len[4];
	int wep_tx_keyidx;
	int local_state_change;

	/**
	 * p2p - Whether this connection is a P2P group
	 */
	int p2p;

	/**
	 * auth_data - Additional elements for Authentication frame
	 *
	 * This buffer starts with the Authentication transaction sequence
	 * number field. If no special handling of such elements is needed, this
	 * pointer is %NULL. This is used with SAE and FILS.
	 */
	const u8 *auth_data;

	/**
	 * auth_data_len - Length of auth_data buffer in octets
	 */
	size_t auth_data_len;

	/**
	 * mld - Establish an MLD connection
	 */
	bool mld;

	/**
	 * mld_link_id - The link ID of the MLD AP to which we are associating
	 */
	u8 mld_link_id;

	/**
	 * The MLD AP address
	 */
	const u8 *ap_mld_addr;
};

/**
 * enum wps_mode - WPS mode
 */
enum wps_mode {
	/**
	 * WPS_MODE_NONE - No WPS provisioning being used
	 */
	WPS_MODE_NONE,

	/**
	 * WPS_MODE_OPEN - WPS provisioning with AP that is in open mode
	 */
	WPS_MODE_OPEN,

	/**
	 * WPS_MODE_PRIVACY - WPS provisioning with AP that is using protection
	 */
	WPS_MODE_PRIVACY
};

/**
 * struct hostapd_freq_params - Channel parameters
 */
struct hostapd_freq_params {
	/**
	 * mode - Mode/band (HOSTAPD_MODE_IEEE80211A, ..)
	 */
	enum hostapd_hw_mode mode;

	/**
	 * freq - Primary channel center frequency in MHz
	 */
	int freq;

	/**
	 * channel - Channel number
	 */
	int channel;

	/**
	 * ht_enabled - Whether HT is enabled
	 */
	int ht_enabled;

	/**
	 * sec_channel_offset - Secondary channel offset for HT40
	 *
	 * 0 = HT40 disabled,
	 * -1 = HT40 enabled, secondary channel below primary,
	 * 1 = HT40 enabled, secondary channel above primary
	 */
	int sec_channel_offset;

	/**
	 * vht_enabled - Whether VHT is enabled
	 */
	int vht_enabled;

	/**
	 * he_enabled - Whether HE is enabled
	 */
	int he_enabled;

	/**
	 * center_freq1 - Segment 0 center frequency in MHz
	 *
	 * Valid for both HT and VHT.
	 */
	int center_freq1;

	/**
	 * center_freq2 - Segment 1 center frequency in MHz
	 *
	 * Non-zero only for bandwidth 80 and an 80+80 channel
	 */
	int center_freq2;

	/**
	 * bandwidth - Channel bandwidth in MHz (20, 40, 80, 160)
	 */
	int bandwidth;

	/**
	 * This structure describes the most essential parameters needed
	 * for IEEE 802.11ay EDMG configuration.
	 */
	struct ieee80211_edmg_config edmg;

	/**
	 * radar_background - Whether radar/CAC background is requested
	 */
	bool radar_background;

	/**
	 * eht_enabled - Whether EHT is enabled
	 */
	bool eht_enabled;

	/**
	 * link_id: If >=0 indicates the link of the AP MLD to configure
	 */
	int link_id;
};

/**
 * struct wpa_driver_sta_auth_params - Authentication parameters
 * Data for struct wpa_driver_ops::sta_auth().
 */
struct wpa_driver_sta_auth_params {

	/**
	 * own_addr - Source address and BSSID for authentication frame
	 */
	const u8 *own_addr;

	/**
	 * addr - MAC address of the station to associate
	 */
	const u8 *addr;

	/**
	 * seq - authentication sequence number
	 */
	u16 seq;

	/**
	 * status - authentication response status code
	 */
	u16 status;

	/**
	 * ie - authentication frame ie buffer
	 */
	const u8 *ie;

	/**
	 * len - ie buffer length
	 */
	size_t len;

	/**
	 * fils_auth - Indicates whether FILS authentication is being performed
	 */
	int fils_auth;

	/**
	 * fils_anonce - ANonce (required for FILS)
	 */
	u8 fils_anonce[WPA_NONCE_LEN];

	/**
	 * fils_snonce - SNonce (required for FILS)
	*/
	u8 fils_snonce[WPA_NONCE_LEN];

	/**
	 * fils_kek - key for encryption (required for FILS)
	 */
	u8 fils_kek[WPA_KEK_MAX_LEN];

	/**
	 * fils_kek_len - Length of the fils_kek in octets (required for FILS)
	 */
	size_t fils_kek_len;
};

struct wpa_driver_mld_params {
	/**
	 * mld_addr - AP's MLD address
	 */
	const u8 *mld_addr;

	/**
	 * valid_links - The valid links including the association link
	 */
	u16 valid_links;

	/**
	 * assoc_link_id - The link on which the association is performed
	 */
	u8 assoc_link_id;

	/**
	 * mld_links - Link information
	 *
	 * Should include information on all the requested links for association
	 * including the link on which the association should take place.
	 * For the association link, the ies and ies_len should be NULL and
	 * 0 respectively.
	 */
	struct {
		int freq;
		const u8 *bssid;
		const u8 *ies;
		size_t ies_len;
		int error;
		bool disabled;
	} mld_links[MAX_NUM_MLD_LINKS];
};

/**
 * struct wpa_driver_associate_params - Association parameters
 * Data for struct wpa_driver_ops::associate().
 */
struct wpa_driver_associate_params {
	/**
	 * bssid - BSSID of the selected AP
	 * This can be %NULL, if ap_scan=2 mode is used and the driver is
	 * responsible for selecting with which BSS to associate. */
	const u8 *bssid;

	/**
	 * bssid_hint - BSSID of a proposed AP
	 *
	 * This indicates which BSS has been found a suitable candidate for
	 * initial association for drivers that use driver/firmwate-based BSS
	 * selection. Unlike the @bssid parameter, @bssid_hint does not limit
	 * the driver from selecting other BSSes in the ESS.
	 */
	const u8 *bssid_hint;

	/**
	 * ssid - The selected SSID
	 */
	const u8 *ssid;

	/**
	 * ssid_len - Length of the SSID (1..32)
	 */
	size_t ssid_len;

	/**
	 * freq - channel parameters
	 */
	struct hostapd_freq_params freq;

	/**
	 * freq_hint - Frequency of the channel the proposed AP is using
	 *
	 * This provides a channel on which a suitable BSS has been found as a
	 * hint for the driver. Unlike the @freq parameter, @freq_hint does not
	 * limit the driver from selecting other channels for
	 * driver/firmware-based BSS selection.
	 */
	int freq_hint;

	/**
	 * bg_scan_period - Background scan period in seconds, 0 to disable
	 * background scan, or -1 to indicate no change to default driver
	 * configuration
	 */
	int bg_scan_period;

	/**
	 * beacon_int - Beacon interval for IBSS or 0 to use driver default
	 */
	int beacon_int;

	/**
	 * wpa_ie - WPA information element for (Re)Association Request
	 * WPA information element to be included in (Re)Association
	 * Request (including information element id and length). Use
	 * of this WPA IE is optional. If the driver generates the WPA
	 * IE, it can use pairwise_suite, group_suite, group_mgmt_suite, and
	 * key_mgmt_suite to select proper algorithms. In this case,
	 * the driver has to notify wpa_supplicant about the used WPA
	 * IE by generating an event that the interface code will
	 * convert into EVENT_ASSOCINFO data (see below).
	 *
	 * When using WPA2/IEEE 802.11i, wpa_ie is used for RSN IE
	 * instead. The driver can determine which version is used by
	 * looking at the first byte of the IE (0xdd for WPA, 0x30 for
	 * WPA2/RSN).
	 *
	 * When using WPS, wpa_ie is used for WPS IE instead of WPA/RSN IE.
	 */
	const u8 *wpa_ie;

	/**
	 * wpa_ie_len - length of the wpa_ie
	 */
	size_t wpa_ie_len;

	/**
	 * wpa_proto - Bitfield of WPA_PROTO_* values to indicate WPA/WPA2
	 */
	unsigned int wpa_proto;

	/**
	 * pairwise_suite - Selected pairwise cipher suite (WPA_CIPHER_*)
	 *
	 * This is usually ignored if @wpa_ie is used.
	 */
	unsigned int pairwise_suite;

	/**
	 * group_suite - Selected group cipher suite (WPA_CIPHER_*)
	 *
	 * This is usually ignored if @wpa_ie is used.
	 */
	unsigned int group_suite;

	/**
	 * mgmt_group_suite - Selected group management cipher suite (WPA_CIPHER_*)
	 *
	 * This is usually ignored if @wpa_ie is used.
	 */
	unsigned int mgmt_group_suite;

	/**
	 * key_mgmt_suite - Selected key management suite (WPA_KEY_MGMT_*)
	 *
	 * This is usually ignored if @wpa_ie is used.
	 */
	unsigned int key_mgmt_suite;

	/**
	 * allowed_key_mgmts - Bitfield of allowed key management suites
	 * (WPA_KEY_MGMT_*) other than @key_mgmt_suite for the current
	 * connection
	 *
	 * SME in the driver may choose key_mgmt from this list for the initial
	 * connection or roaming. The driver which doesn't support this
	 * ignores this parameter.
	 */
	unsigned int allowed_key_mgmts;

	/**
	 * auth_alg - Allowed authentication algorithms
	 * Bit field of WPA_AUTH_ALG_*
	 */
	int auth_alg;

	/**
	 * mode - Operation mode (infra/ibss) IEEE80211_MODE_*
	 */
	int mode;

	/**
	 * wep_key - WEP keys for static WEP configuration
	 */
	const u8 *wep_key[4];

	/**
	 * wep_key_len - WEP key length for static WEP configuration
	 */
	size_t wep_key_len[4];

	/**
	 * wep_tx_keyidx - WEP TX key index for static WEP configuration
	 */
	int wep_tx_keyidx;

	/**
	 * mgmt_frame_protection - IEEE 802.11w management frame protection
	 */
	enum mfp_options mgmt_frame_protection;

	/**
	 * passphrase - RSN passphrase for PSK
	 *
	 * This value is made available only for WPA/WPA2-Personal (PSK) and
	 * only for drivers that set WPA_DRIVER_FLAGS_4WAY_HANDSHAKE_PSK. This
	 * is the 8..63 character ASCII passphrase, if available. Please note
	 * that this can be %NULL if passphrase was not used to generate the
	 * PSK. In that case, the psk field must be used to fetch the PSK.
	 */
	const char *passphrase;

	/**
	 * psk - RSN PSK (alternative for passphrase for PSK)
	 *
	 * This value is made available only for WPA/WPA2-Personal (PSK) and
	 * only for drivers that set WPA_DRIVER_FLAGS_4WAY_HANDSHAKE_PSK. This
	 * is the 32-octet (256-bit) PSK, if available. The driver wrapper
	 * should be prepared to handle %NULL value as an error.
	 */
	const u8 *psk;

	/**
	 * sae_password - Password for SAE authentication
	 *
	 * This value is made available only for WPA3-Personal (SAE) and only
	 * for drivers that set WPA_DRIVER_FLAGS2_SAE_OFFLOAD.
	 */
	const char *sae_password;

	/**
	 * sae_password_id - Password Identifier for SAE authentication
	 *
	 * This value is made available only for WPA3-Personal (SAE) and only
	 * for drivers that set WPA_DRIVER_FLAGS2_SAE_OFFLOAD. If %NULL, SAE
	 * password identifier is not used.
	 */
	const char *sae_password_id;

	/**
	 * drop_unencrypted - Enable/disable unencrypted frame filtering
	 *
	 * Configure the driver to drop all non-EAPOL frames (both receive and
	 * transmit paths). Unencrypted EAPOL frames (ethertype 0x888e) must
	 * still be allowed for key negotiation.
	 */
	int drop_unencrypted;

	/**
	 * prev_bssid - Previously used BSSID in this ESS
	 *
	 * When not %NULL, this is a request to use reassociation instead of
	 * association.
	 */
	const u8 *prev_bssid;

	/**
	 * wps - WPS mode
	 *
	 * If the driver needs to do special configuration for WPS association,
	 * this variable provides more information on what type of association
	 * is being requested. Most drivers should not need to use this.
	 */
	enum wps_mode wps;

	/**
	 * p2p - Whether this connection is a P2P group
	 */
	int p2p;

	/**
	 * uapsd - UAPSD parameters for the network
	 * -1 = do not change defaults
	 * AP mode: 1 = enabled, 0 = disabled
	 * STA mode: bits 0..3 UAPSD enabled for VO,VI,BK,BE
	 */
	int uapsd;

	/**
	 * fixed_bssid - Whether to force this BSSID in IBSS mode
	 * 1 = Fix this BSSID and prevent merges.
	 * 0 = Do not fix BSSID.
	 */
	int fixed_bssid;

	/**
	 * fixed_freq - Fix control channel in IBSS mode
	 * 0 = don't fix control channel (default)
	 * 1 = fix control channel; this prevents IBSS merging with another
	 *	channel
	 */
	int fixed_freq;

	/**
	 * disable_ht - Disable HT (IEEE 802.11n) for this connection
	 */
	int disable_ht;

	/**
	 * htcaps - HT Capabilities over-rides
	 *
	 * Only bits set in the mask will be used, and not all values are used
	 * by the kernel anyway. Currently, MCS, MPDU and MSDU fields are used.
	 *
	 * Pointer to struct ieee80211_ht_capabilities.
	 */
	const u8 *htcaps;

	/**
	 * htcaps_mask - HT Capabilities over-rides mask
	 *
	 * Pointer to struct ieee80211_ht_capabilities.
	 */
	const u8 *htcaps_mask;

#ifdef CONFIG_VHT_OVERRIDES
	/**
	 * disable_vht - Disable VHT for this connection
	 */
	int disable_vht;

	/**
	 * VHT capability overrides.
	 */
	const struct ieee80211_vht_capabilities *vhtcaps;
	const struct ieee80211_vht_capabilities *vhtcaps_mask;
#endif /* CONFIG_VHT_OVERRIDES */

#ifdef CONFIG_HE_OVERRIDES
	/**
	 * disable_he - Disable HE for this connection
	 */
	int disable_he;
#endif /* CONFIG_HE_OVERRIDES */

	/**
	 * req_key_mgmt_offload - Request key management offload for connection
	 *
	 * Request key management offload for this connection if the device
	 * supports it.
	 */
	int req_key_mgmt_offload;

	/**
	 * req_handshake_offload - Request EAPOL handshake offload
	 *
	 * Request EAPOL handshake offload for this connection if the device
	 * supports it.
	 */
	int req_handshake_offload;

	/**
	 * Flag for indicating whether this association includes support for
	 * RRM (Radio Resource Measurements)
	 */
	int rrm_used;

	/**
	 * pbss - If set, connect to a PCP in a PBSS. Otherwise, connect to an
	 * AP as usual. Valid for DMG network only.
	 */
	int pbss;

	/**
	 * fils_kek - KEK for FILS association frame protection (AES-SIV)
	 */
	const u8 *fils_kek;

	/**
	 * fils_kek_len: Length of fils_kek in bytes
	 */
	size_t fils_kek_len;

	/**
	 * fils_nonces - Nonces for FILS association frame protection
	 * (AES-SIV AAD)
	 */
	const u8 *fils_nonces;

	/**
	 * fils_nonces_len: Length of fils_nonce in bytes
	 */
	size_t fils_nonces_len;

	/**
	 * fils_erp_username - Username part of keyName-NAI
	 */
	const u8 *fils_erp_username;

	/**
	 * fils_erp_username_len - Length of fils_erp_username in bytes
	 */
	size_t fils_erp_username_len;

	/**
	 * fils_erp_realm - Realm/domain name to use in FILS ERP
	 */
	const u8 *fils_erp_realm;

	/**
	 * fils_erp_realm_len - Length of fils_erp_realm in bytes
	 */
	size_t fils_erp_realm_len;

	/**
	 * fils_erp_next_seq_num - The next sequence number to use in FILS ERP
	 * messages
	 */
	u16 fils_erp_next_seq_num;

	/**
	 * fils_erp_rrk - Re-authentication root key (rRK) for the keyName-NAI
	 * specified by fils_erp_username@fils_erp_realm.
	 */
	const u8 *fils_erp_rrk;

	/**
	 * fils_erp_rrk_len - Length of fils_erp_rrk in bytes
	 */
	size_t fils_erp_rrk_len;

	/**
	 * sae_pwe - SAE mechanism for PWE derivation
	 * 0 = hunting-and-pecking loop only
	 * 1 = hash-to-element only
	 * 2 = both hunting-and-pecking loop and hash-to-element enabled
	 */
	enum sae_pwe sae_pwe;

	/**
	 * disable_eht - Disable EHT for this connection
	 */
	int disable_eht;

	/*
	 * mld_params - MLD association parameters
	 */
	struct wpa_driver_mld_params mld_params;
};

enum hide_ssid {
	NO_SSID_HIDING,
	HIDDEN_SSID_ZERO_LEN,
	HIDDEN_SSID_ZERO_CONTENTS
};

enum ch_switch_state {
	CH_SW_STARTED,
	CH_SW_FINISHED
};

struct wowlan_triggers {
	u8 any;
	u8 disconnect;
	u8 magic_pkt;
	u8 gtk_rekey_failure;
	u8 eap_identity_req;
	u8 four_way_handshake;
	u8 rfkill_release;
};

struct unsol_bcast_probe_resp {
	/**
	 * Unsolicited broadcast Probe Response interval in TUs
	 */
	unsigned int unsol_bcast_probe_resp_interval;

	/**
	 * Unsolicited broadcast Probe Response template data
	 */
	u8 *unsol_bcast_probe_resp_tmpl;

	/**
	 * Unsolicited broadcast Probe Response template length
	 */
	size_t unsol_bcast_probe_resp_tmpl_len;
};

struct wpa_driver_ap_params {
	/**
	 * head - Beacon head from IEEE 802.11 header to IEs before TIM IE
	 */
	u8 *head;

	/**
	 * head_len - Length of the head buffer in octets
	 */
	size_t head_len;

	/**
	 * tail - Beacon tail following TIM IE
	 */
	u8 *tail;

	/**
	 * tail_len - Length of the tail buffer in octets
	 */
	size_t tail_len;

	/**
	 * dtim_period - DTIM period
	 */
	int dtim_period;

	/**
	 * beacon_int - Beacon interval
	 */
	int beacon_int;

	/**
	 * basic_rates: -1 terminated array of basic rates in 100 kbps
	 *
	 * This parameter can be used to set a specific basic rate set for the
	 * BSS. If %NULL, default basic rate set is used.
	 */
	int *basic_rates;

	/**
	 * beacon_rate: Beacon frame data rate
	 *
	 * This parameter can be used to set a specific Beacon frame data rate
	 * for the BSS. The interpretation of this value depends on the
	 * rate_type (legacy: in 100 kbps units, HT: HT-MCS, VHT: VHT-MCS,
	 * HE: HE-MCS). If beacon_rate == 0 and rate_type == 0
	 * (BEACON_RATE_LEGACY), the default Beacon frame data rate is used.
	 */
	unsigned int beacon_rate;

	/**
	 * beacon_rate_type: Beacon data rate type (legacy/HT/VHT/HE)
	 */
	enum beacon_rate_type rate_type;

	/**
	 * proberesp - Probe Response template
	 *
	 * This is used by drivers that reply to Probe Requests internally in
	 * AP mode and require the full Probe Response template.
	 */
	u8 *proberesp;

	/**
	 * proberesp_len - Length of the proberesp buffer in octets
	 */
	size_t proberesp_len;

	/**
	 * ssid - The SSID to use in Beacon/Probe Response frames
	 */
	const u8 *ssid;

	/**
	 * ssid_len - Length of the SSID (1..32)
	 */
	size_t ssid_len;

	/**
	 * hide_ssid - Whether to hide the SSID
	 */
	enum hide_ssid hide_ssid;

	/**
	 * pairwise_ciphers - WPA_CIPHER_* bitfield
	 */
	unsigned int pairwise_ciphers;

	/**
	 * group_cipher - WPA_CIPHER_*
	 */
	unsigned int group_cipher;

	/**
	 * key_mgmt_suites - WPA_KEY_MGMT_* bitfield
	 */
	unsigned int key_mgmt_suites;

	/**
	 * auth_algs - WPA_AUTH_ALG_* bitfield
	 */
	unsigned int auth_algs;

	/**
	 * wpa_version - WPA_PROTO_* bitfield
	 */
	unsigned int wpa_version;

	/**
	 * privacy - Whether privacy is used in the BSS
	 */
	int privacy;

	/**
	 * beacon_ies - WPS/P2P IE(s) for Beacon frames
	 *
	 * This is used to add IEs like WPS IE and P2P IE by drivers that do
	 * not use the full Beacon template.
	 */
	const struct wpabuf *beacon_ies;

	/**
	 * proberesp_ies - P2P/WPS IE(s) for Probe Response frames
	 *
	 * This is used to add IEs like WPS IE and P2P IE by drivers that
	 * reply to Probe Request frames internally.
	 */
	const struct wpabuf *proberesp_ies;

	/**
	 * assocresp_ies - WPS IE(s) for (Re)Association Response frames
	 *
	 * This is used to add IEs like WPS IE by drivers that reply to
	 * (Re)Association Request frames internally.
	 */
	const struct wpabuf *assocresp_ies;

	/**
	 * isolate - Whether to isolate frames between associated stations
	 *
	 * If this is non-zero, the AP is requested to disable forwarding of
	 * frames between associated stations.
	 */
	int isolate;

	/**
	 * cts_protect - Whether CTS protection is enabled
	 */
	int cts_protect;

	/**
	 * preamble - Whether short preamble is enabled
	 */
	int preamble;

	/**
	 * short_slot_time - Whether short slot time is enabled
	 *
	 * 0 = short slot time disable, 1 = short slot time enabled, -1 = do
	 * not set (e.g., when 802.11g mode is not in use)
	 */
	int short_slot_time;

	/**
	 * ht_opmode - HT operation mode or -1 if HT not in use
	 */
	int ht_opmode;

	/**
	 * interworking - Whether Interworking is enabled
	 */
	int interworking;

	/**
	 * hessid - Homogeneous ESS identifier or %NULL if not set
	 */
	const u8 *hessid;

	/**
	 * access_network_type - Access Network Type (0..15)
	 *
	 * This is used for filtering Probe Request frames when Interworking is
	 * enabled.
	 */
	u8 access_network_type;

	/**
	 * ap_max_inactivity - Timeout in seconds to detect STA's inactivity
	 *
	 * This is used by driver which advertises this capability.
	 */
	int ap_max_inactivity;

	/**
	 * ctwindow - Client Traffic Window (in TUs)
	 */
	u8 p2p_go_ctwindow;

	/**
	 * disable_dgaf - Whether group-addressed frames are disabled
	 */
	int disable_dgaf;

	/**
	 * osen - Whether OSEN security is enabled
	 */
	int osen;

	/**
	 * freq - Channel parameters for dynamic bandwidth changes
	 */
	struct hostapd_freq_params *freq;

	/**
	 * reenable - Whether this is to re-enable beaconing
	 */
	int reenable;

	/**
	 * pbss - Whether to start a PCP (in PBSS) instead of an AP in
	 * infrastructure BSS. Valid only for DMG network.
	 */
	int pbss;

	/**
	 * multicast_to_unicast - Whether to use multicast_to_unicast
	 *
	 * If this is non-zero, the AP is requested to perform multicast to
	 * unicast conversion for ARP, IPv4, and IPv6 frames (possibly within
	 * 802.1Q). If enabled, such frames are to be sent to each station
	 * separately, with the DA replaced by their own MAC address rather
	 * than the group address.
	 *
	 * Note that this may break certain expectations of the receiver, such
	 * as the ability to drop unicast IP packets received within multicast
	 * L2 frames, or the ability to not send ICMP destination unreachable
	 * messages for packets received in L2 multicast (which is required,
	 * but the receiver can't tell the difference if this new option is
	 * enabled.)
	 *
	 * This also doesn't implement the 802.11 DMS (directed multicast
	 * service).
	 */
	int multicast_to_unicast;

	/**
	 * ftm_responder - Whether FTM responder is enabled
	 */
	int ftm_responder;

	/**
	 * lci - Binary data, the content of an LCI report IE with type 8 as
	 * defined in IEEE Std 802.11-2016, 9.4.2.22.10
	 */
	const struct wpabuf *lci;

	/**
	 * civic - Binary data, the content of a measurement report IE with
	 * type 11 as defined in IEEE Std 802.11-2016, 9.4.2.22.13
	 */
	const struct wpabuf *civic;

	/**
	 * he_spr_ctrl - Spatial Reuse control field of SPR element
	 */
	u8 he_spr_ctrl;

	/**
	 * he_spr_non_srg_obss_pd_max_offset - Non-SRG Maximum TX power offset
	 */
	u8 he_spr_non_srg_obss_pd_max_offset;

	/**
	 * he_spr_srg_obss_pd_min_offset - Minimum TX power offset
	 */
	u8 he_spr_srg_obss_pd_min_offset;

	/**
	 * he_spr_srg_obss_pd_max_offset - Maximum TX power offset
	 */
	u8 he_spr_srg_obss_pd_max_offset;

	/**
	 * he_spr_bss_color_bitmap - BSS color values used by members of the
	 * SRG.
	 */
	u8 he_spr_bss_color_bitmap[8];

	/**
	 * he_spr_partial_bssid_bitmap - Partial BSSID values used by members
	 * of the SRG.
	 */
	u8 he_spr_partial_bssid_bitmap[8];

	/**
	 * he_bss_color - Whether the BSS Color is disabled
	 */
	int he_bss_color_disabled;

	/**
	 * he_bss_color_partial - The BSS Color AID equation
	 */
	int he_bss_color_partial;

	/**
	 * he_bss_color - The BSS Color of the AP
	 */
	int he_bss_color;

	/**
	 * twt_responder - Whether Target Wait Time responder is enabled
	 */
	int twt_responder;

	/**
	 * sae_pwe - SAE mechanism for PWE derivation
	 * 0 = hunting-and-pecking loop only
	 * 1 = hash-to-element only
	 * 2 = both hunting-and-pecking loop and hash-to-element enabled
	 */
	enum sae_pwe sae_pwe;

	/**
	 * FILS Discovery frame minimum interval in TUs
	 */
	u32 fd_min_int;

	/**
	 * FILS Discovery frame maximum interval in TUs (0 = FD frame disabled)
	 */
	u32 fd_max_int;

	/**
	 * FILS Discovery frame template data
	 */
	u8 *fd_frame_tmpl;

	/**
	 * FILS Discovery frame template length
	 */
	size_t fd_frame_tmpl_len;

	/**
	 * mbssid_tx_iface - Transmitting interface of the MBSSID set
	 */
	const char *mbssid_tx_iface;

	/**
	 * mbssid_index - The index of this BSS in the MBSSID set
	 */
	unsigned int mbssid_index;

	/**
	 * mbssid_elem - Buffer containing all MBSSID elements
	 */
	u8 *mbssid_elem;

	/**
	 * mbssid_elem_len - Total length of all MBSSID elements
	 */
	size_t mbssid_elem_len;

	/**
	 * mbssid_elem_count - The number of MBSSID elements
	 */
	u8 mbssid_elem_count;

	/**
	 * mbssid_elem_offset - Offsets to elements in mbssid_elem.
	 * Kernel will use these offsets to generate multiple BSSID beacons.
	 */
	u8 **mbssid_elem_offset;

	/**
	 * ema - Enhanced MBSSID advertisements support.
	 */
	bool ema;

	/**
	 * punct_bitmap - Preamble puncturing bitmap
	 * Each bit corresponds to a 20 MHz subchannel, the lowest bit for the
	 * channel with the lowest frequency. A bit set to 1 indicates that the
	 * subchannel is punctured, otherwise active.
	 */
	u16 punct_bitmap;

	/**
	 * rnr_elem - This buffer contains all of reduced neighbor report (RNR)
	 * elements
	 */
	u8 *rnr_elem;

	/**
	 * rnr_elem_len - Length of rnr_elem buffer
	 */
	size_t rnr_elem_len;

	/**
	 * rnr_elem_count - Number of RNR elements
	 */
	unsigned int rnr_elem_count;

	/**
	 * rnr_elem_offset - The offsets to the elements in rnr_elem.
	 * The driver will use these to include RNR elements in EMA beacons.
	 */
	u8 **rnr_elem_offset;

	/* Unsolicited broadcast Probe Response data */
	struct unsol_bcast_probe_resp ubpr;

	/**
	 * allowed_freqs - List of allowed 20 MHz channel center frequencies in
	 * MHz for AP operation. Drivers which support this parameter will
	 * generate a new list based on this provided list by filtering out
	 * channels that cannot be used at that time due to regulatory or other
	 * constraints. The resulting list is used as the list of all allowed
	 * channels whenever performing operations like ACS and DFS.
	 */
	int *allowed_freqs;

	/*
	 * mld_ap - Whether operating as an AP MLD
	 */
	bool mld_ap;

	/**
	 * mld_link_id - Link id for MLD BSS's
	 */
	u8 mld_link_id;

	/**
	 * psk - PSK passed to the driver for 4-way handshake offload
	 */
	u8 psk[PMK_LEN];

	/**
	 * psk_len - PSK length in bytes (0 = not set)
	 */
	size_t psk_len;

	/**
	 * sae_password - SAE password for SAE offload
	 */
	const char *sae_password;
};

struct wpa_driver_mesh_bss_params {
#define WPA_DRIVER_MESH_CONF_FLAG_AUTO_PLINKS		0x00000001
#define WPA_DRIVER_MESH_CONF_FLAG_PEER_LINK_TIMEOUT	0x00000002
#define WPA_DRIVER_MESH_CONF_FLAG_MAX_PEER_LINKS	0x00000004
#define WPA_DRIVER_MESH_CONF_FLAG_HT_OP_MODE		0x00000008
#define WPA_DRIVER_MESH_CONF_FLAG_RSSI_THRESHOLD	0x00000010
#define WPA_DRIVER_MESH_CONF_FLAG_FORWARDING		0x00000020
	/*
	 * TODO: Other mesh configuration parameters would go here.
	 * See NL80211_MESHCONF_* for all the mesh config parameters.
	 */
	unsigned int flags;
	int auto_plinks;
	int peer_link_timeout;
	int max_peer_links;
	int rssi_threshold;
	int forwarding;
	u16 ht_opmode;
};

struct wpa_driver_mesh_join_params {
	const u8 *meshid;
	int meshid_len;
	const int *basic_rates;
	const u8 *ies;
	int ie_len;
	struct hostapd_freq_params freq;
	int beacon_int;
	int dtim_period;
	struct wpa_driver_mesh_bss_params conf;
#define WPA_DRIVER_MESH_FLAG_USER_MPM	0x00000001
#define WPA_DRIVER_MESH_FLAG_DRIVER_MPM	0x00000002
#define WPA_DRIVER_MESH_FLAG_SAE_AUTH	0x00000004
#define WPA_DRIVER_MESH_FLAG_AMPE	0x00000008
	unsigned int flags;
	bool handle_dfs;
};

struct wpa_driver_set_key_params {
	/**
	 * ifname - Interface name (for multi-SSID/VLAN support) */
	const char *ifname;

	/**
	 * alg - Encryption algorithm
	 *
	 * (%WPA_ALG_NONE, %WPA_ALG_WEP, %WPA_ALG_TKIP, %WPA_ALG_CCMP,
	 * %WPA_ALG_BIP_AES_CMAC_128, %WPA_ALG_GCMP, %WPA_ALG_GCMP_256,
	 * %WPA_ALG_CCMP_256, %WPA_ALG_BIP_GMAC_128, %WPA_ALG_BIP_GMAC_256,
	 * %WPA_ALG_BIP_CMAC_256);
	 * %WPA_ALG_NONE clears the key. */
	enum wpa_alg alg;

	/**
	 * addr - Address of the peer STA
	 *
	 * (BSSID of the current AP when setting pairwise key in station mode),
	 * ff:ff:ff:ff:ff:ff for broadcast keys, %NULL for default keys that
	 * are used both for broadcast and unicast; when clearing keys, %NULL
	 * is used to indicate that both the broadcast-only and default key of
	 * the specified key index is to be cleared */
	const u8 *addr;

	/**
	 * key_idx - Key index
	 *
	 * (0..3), usually 0 for unicast keys; 4..5 for IGTK; 6..7 for BIGTK */
	int key_idx;

	/**
	 * set_tx - Configure this key as the default Tx key
	 *
	 * Only used when driver does not support separate unicast/individual
	 * key */
	int set_tx;

	/**
	 * seq - Sequence number/packet number
	 *
	 * seq_len octets, the next packet number to be used for in replay
	 * protection; configured for Rx keys (in most cases, this is only used
	 * with broadcast keys and set to zero for unicast keys); %NULL if not
	 * set */
	const u8 *seq;

	/**
	 * seq_len - Length of the seq, depends on the algorithm
	 *
	 * TKIP: 6 octets, CCMP/GCMP: 6 octets, IGTK: 6 octets */
	size_t seq_len;

	/**
	 * key - Key buffer
	 *
	 * TKIP: 16-byte temporal key, 8-byte Tx Mic key, 8-byte Rx Mic Key */
	const u8 *key;

	/**
	 * key_len - Length of the key buffer in octets
	 *
	 * WEP: 5 or 13, TKIP: 32, CCMP/GCMP: 16, IGTK: 16 */
	size_t key_len;

	/**
	 * vlan_id - VLAN index (0..4095) for VLAN offload cases */
	int vlan_id;

	/**
	 * key_flag - Additional key flags
	 *
	 * %KEY_FLAG_MODIFY
	 *  Set when an already installed key must be updated.
	 *  So far the only use-case is changing RX/TX status for
	 *  pairwise keys. Must not be set when deleting a key.
	 * %KEY_FLAG_DEFAULT
	 *  Set when the key is also a default key. Must not be set when
	 *  deleting a key.
	 * %KEY_FLAG_RX
	 *  The key is valid for RX. Must not be set when deleting a key.
	 * %KEY_FLAG_TX
	 *  The key is valid for TX. Must not be set when deleting a key.
	 * %KEY_FLAG_GROUP
	 *  The key is a broadcast or group key.
	 * %KEY_FLAG_PAIRWISE
	 *  The key is a pairwise key.
	 * %KEY_FLAG_PMK
	 *  The key is a Pairwise Master Key (PMK).
	 *
	 * Valid and pre-defined combinations are:
	 * %KEY_FLAG_GROUP_RX_TX
	 *  WEP key not to be installed as default key.
	 * %KEY_FLAG_GROUP_RX_TX_DEFAULT
	 *  Default WEP or WPA-NONE key.
	 * %KEY_FLAG_GROUP_RX
	 *  GTK key valid for RX only.
	 * %KEY_FLAG_GROUP_TX_DEFAULT
	 *  GTK key valid for TX only, immediately taking over TX.
	 * %KEY_FLAG_PAIRWISE_RX_TX
	 *  Pairwise key immediately becoming the active pairwise key.
	 * %KEY_FLAG_PAIRWISE_RX
	 *  Pairwise key not yet valid for TX. (Only usable when Extended
	 *  Key ID is supported by the driver.)
	 * %KEY_FLAG_PAIRWISE_RX_TX_MODIFY
	 *  Enable TX for a pairwise key installed with
	 *  KEY_FLAG_PAIRWISE_RX.
	 *
	 * Not a valid standalone key type but pre-defined to be combined
	 * with other key_flags:
	 * %KEY_FLAG_RX_TX
	 *  RX/TX key. */
	enum key_flag key_flag;

	/**
	 * link_id - MLO Link ID
	 *
	 * Set to a valid Link ID (0-14) when applicable, otherwise -1. */
	int link_id;
};

enum wpa_driver_if_type {
	/**
	 * WPA_IF_STATION - Station mode interface
	 */
	WPA_IF_STATION,

	/**
	 * WPA_IF_AP_VLAN - AP mode VLAN interface
	 *
	 * This interface shares its address and Beacon frame with the main
	 * BSS.
	 */
	WPA_IF_AP_VLAN,

	/**
	 * WPA_IF_AP_BSS - AP mode BSS interface
	 *
	 * This interface has its own address and Beacon frame.
	 */
	WPA_IF_AP_BSS,

	/**
	 * WPA_IF_P2P_GO - P2P Group Owner
	 */
	WPA_IF_P2P_GO,

	/**
	 * WPA_IF_P2P_CLIENT - P2P Client
	 */
	WPA_IF_P2P_CLIENT,

	/**
	 * WPA_IF_P2P_GROUP - P2P Group interface (will become either
	 * WPA_IF_P2P_GO or WPA_IF_P2P_CLIENT, but the role is not yet known)
	 */
	WPA_IF_P2P_GROUP,

	/**
	 * WPA_IF_P2P_DEVICE - P2P Device interface is used to identify the
	 * abstracted P2P Device function in the driver
	 */
	WPA_IF_P2P_DEVICE,

	/*
	 * WPA_IF_MESH - Mesh interface
	 */
	WPA_IF_MESH,

	/*
	 * WPA_IF_TDLS - TDLS offchannel interface (used for pref freq only)
	 */
	WPA_IF_TDLS,

	/*
	 * WPA_IF_IBSS - IBSS interface (used for pref freq only)
	 */
	WPA_IF_IBSS,

	/*
	 * WPA_IF_NAN - NAN Device
	 */
	WPA_IF_NAN,

	/* keep last */
	WPA_IF_MAX
};

/**
 * struct wpa_driver_capa - Driver capability information
 */
struct wpa_driver_capa {
#define WPA_DRIVER_CAPA_KEY_MGMT_WPA		0x00000001
#define WPA_DRIVER_CAPA_KEY_MGMT_WPA2		0x00000002
#define WPA_DRIVER_CAPA_KEY_MGMT_WPA_PSK	0x00000004
#define WPA_DRIVER_CAPA_KEY_MGMT_WPA2_PSK	0x00000008
#define WPA_DRIVER_CAPA_KEY_MGMT_WPA_NONE	0x00000010
#define WPA_DRIVER_CAPA_KEY_MGMT_FT		0x00000020
#define WPA_DRIVER_CAPA_KEY_MGMT_FT_PSK		0x00000040
#define WPA_DRIVER_CAPA_KEY_MGMT_WAPI_PSK	0x00000080
#define WPA_DRIVER_CAPA_KEY_MGMT_SUITE_B	0x00000100
#define WPA_DRIVER_CAPA_KEY_MGMT_SUITE_B_192	0x00000200
#define WPA_DRIVER_CAPA_KEY_MGMT_OWE		0x00000400
#define WPA_DRIVER_CAPA_KEY_MGMT_DPP		0x00000800
#define WPA_DRIVER_CAPA_KEY_MGMT_FILS_SHA256    0x00001000
#define WPA_DRIVER_CAPA_KEY_MGMT_FILS_SHA384    0x00002000
#define WPA_DRIVER_CAPA_KEY_MGMT_FT_FILS_SHA256 0x00004000
#define WPA_DRIVER_CAPA_KEY_MGMT_FT_FILS_SHA384 0x00008000
#define WPA_DRIVER_CAPA_KEY_MGMT_SAE 		0x00010000
#define WPA_DRIVER_CAPA_KEY_MGMT_802_1X_SHA256	0x00020000
#define WPA_DRIVER_CAPA_KEY_MGMT_PSK_SHA256	0x00040000
#define WPA_DRIVER_CAPA_KEY_MGMT_TPK_HANDSHAKE	0x00080000
#define WPA_DRIVER_CAPA_KEY_MGMT_FT_SAE		0x00100000
#define WPA_DRIVER_CAPA_KEY_MGMT_FT_802_1X_SHA384	0x00200000
#define WPA_DRIVER_CAPA_KEY_MGMT_CCKM		0x00400000
#define WPA_DRIVER_CAPA_KEY_MGMT_OSEN		0x00800000
#define WPA_DRIVER_CAPA_KEY_MGMT_SAE_EXT_KEY	0x01000000
#define WPA_DRIVER_CAPA_KEY_MGMT_FT_SAE_EXT_KEY	0x02000000
	/** Bitfield of supported key management suites */
	unsigned int key_mgmt;
	unsigned int key_mgmt_iftype[WPA_IF_MAX];

#define WPA_DRIVER_CAPA_ENC_WEP40	0x00000001
#define WPA_DRIVER_CAPA_ENC_WEP104	0x00000002
#define WPA_DRIVER_CAPA_ENC_TKIP	0x00000004
#define WPA_DRIVER_CAPA_ENC_CCMP	0x00000008
#define WPA_DRIVER_CAPA_ENC_WEP128	0x00000010
#define WPA_DRIVER_CAPA_ENC_GCMP	0x00000020
#define WPA_DRIVER_CAPA_ENC_GCMP_256	0x00000040
#define WPA_DRIVER_CAPA_ENC_CCMP_256	0x00000080
#define WPA_DRIVER_CAPA_ENC_BIP		0x00000100
#define WPA_DRIVER_CAPA_ENC_BIP_GMAC_128	0x00000200
#define WPA_DRIVER_CAPA_ENC_BIP_GMAC_256	0x00000400
#define WPA_DRIVER_CAPA_ENC_BIP_CMAC_256	0x00000800
#define WPA_DRIVER_CAPA_ENC_GTK_NOT_USED	0x00001000
	/** Bitfield of supported cipher suites */
	unsigned int enc;

#define WPA_DRIVER_AUTH_OPEN		0x00000001
#define WPA_DRIVER_AUTH_SHARED		0x00000002
#define WPA_DRIVER_AUTH_LEAP		0x00000004
	/** Bitfield of supported IEEE 802.11 authentication algorithms */
	unsigned int auth;

/** Driver generated WPA/RSN IE */
#define WPA_DRIVER_FLAGS_DRIVER_IE	0x00000001
/** Driver needs static WEP key setup after association command */
#define WPA_DRIVER_FLAGS_SET_KEYS_AFTER_ASSOC 0x00000002
/** Driver takes care of all DFS operations */
#define WPA_DRIVER_FLAGS_DFS_OFFLOAD			0x00000004
/** Driver takes care of RSN 4-way handshake internally; PMK is configured with
 * struct wpa_driver_ops::set_key using key_flag = KEY_FLAG_PMK */
#define WPA_DRIVER_FLAGS_4WAY_HANDSHAKE_8021X		0x00000008
/** Driver is for a wired Ethernet interface */
#define WPA_DRIVER_FLAGS_WIRED		0x00000010
/** Driver provides separate commands for authentication and association (SME in
 * wpa_supplicant). */
#define WPA_DRIVER_FLAGS_SME		0x00000020
/** Driver supports AP mode */
#define WPA_DRIVER_FLAGS_AP		0x00000040
/** Driver needs static WEP key setup after association has been completed */
#define WPA_DRIVER_FLAGS_SET_KEYS_AFTER_ASSOC_DONE	0x00000080
/** Driver supports dynamic HT 20/40 MHz channel changes during BSS lifetime */
#define WPA_DRIVER_FLAGS_HT_2040_COEX			0x00000100
/** Driver supports concurrent P2P operations */
#define WPA_DRIVER_FLAGS_P2P_CONCURRENT	0x00000200
/**
 * Driver uses the initial interface as a dedicated management interface, i.e.,
 * it cannot be used for P2P group operations or non-P2P purposes.
 */
#define WPA_DRIVER_FLAGS_P2P_DEDICATED_INTERFACE	0x00000400
/** This interface is P2P capable (P2P GO or P2P Client) */
#define WPA_DRIVER_FLAGS_P2P_CAPABLE	0x00000800
/** Driver supports station and key removal when stopping an AP */
#define WPA_DRIVER_FLAGS_AP_TEARDOWN_SUPPORT		0x00001000
/**
 * Driver uses the initial interface for P2P management interface and non-P2P
 * purposes (e.g., connect to infra AP), but this interface cannot be used for
 * P2P group operations.
 */
#define WPA_DRIVER_FLAGS_P2P_MGMT_AND_NON_P2P		0x00002000
/**
 * Driver is known to use valid error codes, i.e., when it indicates that
 * something (e.g., association) fails, there was indeed a failure and the
 * operation does not end up getting completed successfully later.
 */
#define WPA_DRIVER_FLAGS_VALID_ERROR_CODES		0x00004000
/** Driver supports off-channel TX */
#define WPA_DRIVER_FLAGS_OFFCHANNEL_TX			0x00008000
/** Driver indicates TX status events for EAPOL Data frames */
#define WPA_DRIVER_FLAGS_EAPOL_TX_STATUS		0x00010000
/** Driver indicates TX status events for Deauth/Disassoc frames */
#define WPA_DRIVER_FLAGS_DEAUTH_TX_STATUS		0x00020000
/** Driver supports roaming (BSS selection) in firmware */
#define WPA_DRIVER_FLAGS_BSS_SELECTION			0x00040000
/** Driver supports operating as a TDLS peer */
#define WPA_DRIVER_FLAGS_TDLS_SUPPORT			0x00080000
/** Driver requires external TDLS setup/teardown/discovery */
#define WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP		0x00100000
/** Driver indicates support for Probe Response offloading in AP mode */
#define WPA_DRIVER_FLAGS_PROBE_RESP_OFFLOAD		0x00200000
/** Driver supports U-APSD in AP mode */
#define WPA_DRIVER_FLAGS_AP_UAPSD			0x00400000
/** Driver supports inactivity timer in AP mode */
#define WPA_DRIVER_FLAGS_INACTIVITY_TIMER		0x00800000
/** Driver expects user space implementation of MLME in AP mode */
#define WPA_DRIVER_FLAGS_AP_MLME			0x01000000
/** Driver supports SAE with user space SME */
#define WPA_DRIVER_FLAGS_SAE				0x02000000
/** Driver makes use of OBSS scan mechanism in wpa_supplicant */
#define WPA_DRIVER_FLAGS_OBSS_SCAN			0x04000000
/** Driver supports IBSS (Ad-hoc) mode */
#define WPA_DRIVER_FLAGS_IBSS				0x08000000
/** Driver supports radar detection */
#define WPA_DRIVER_FLAGS_RADAR				0x10000000
/** Driver supports a dedicated interface for P2P Device */
#define WPA_DRIVER_FLAGS_DEDICATED_P2P_DEVICE		0x20000000
/** Driver supports QoS Mapping */
#define WPA_DRIVER_FLAGS_QOS_MAPPING			0x40000000
/** Driver supports CSA in AP mode */
#define WPA_DRIVER_FLAGS_AP_CSA				0x80000000
/** Driver supports mesh */
#define WPA_DRIVER_FLAGS_MESH			0x0000000100000000ULL
/** Driver support ACS offload */
#define WPA_DRIVER_FLAGS_ACS_OFFLOAD		0x0000000200000000ULL
/** Driver supports key management offload */
#define WPA_DRIVER_FLAGS_KEY_MGMT_OFFLOAD	0x0000000400000000ULL
/** Driver supports TDLS channel switching */
#define WPA_DRIVER_FLAGS_TDLS_CHANNEL_SWITCH	0x0000000800000000ULL
/** Driver supports IBSS with HT datarates */
#define WPA_DRIVER_FLAGS_HT_IBSS		0x0000001000000000ULL
/** Driver supports IBSS with VHT datarates */
#define WPA_DRIVER_FLAGS_VHT_IBSS		0x0000002000000000ULL
/** Driver supports automatic band selection */
#define WPA_DRIVER_FLAGS_SUPPORT_HW_MODE_ANY	0x0000004000000000ULL
/** Driver supports simultaneous off-channel operations */
#define WPA_DRIVER_FLAGS_OFFCHANNEL_SIMULTANEOUS	0x0000008000000000ULL
/** Driver supports full AP client state */
#define WPA_DRIVER_FLAGS_FULL_AP_CLIENT_STATE	0x0000010000000000ULL
/** Driver supports P2P Listen offload */
#define WPA_DRIVER_FLAGS_P2P_LISTEN_OFFLOAD     0x0000020000000000ULL
/** Driver supports FILS */
#define WPA_DRIVER_FLAGS_SUPPORT_FILS		0x0000040000000000ULL
/** Driver supports Beacon frame TX rate configuration (legacy rates) */
#define WPA_DRIVER_FLAGS_BEACON_RATE_LEGACY	0x0000080000000000ULL
/** Driver supports Beacon frame TX rate configuration (HT rates) */
#define WPA_DRIVER_FLAGS_BEACON_RATE_HT		0x0000100000000000ULL
/** Driver supports Beacon frame TX rate configuration (VHT rates) */
#define WPA_DRIVER_FLAGS_BEACON_RATE_VHT	0x0000200000000000ULL
/** Driver supports mgmt_tx with random TX address in non-connected state */
#define WPA_DRIVER_FLAGS_MGMT_TX_RANDOM_TA	0x0000400000000000ULL
/** Driver supports mgmt_tx with random TX addr in connected state */
#define WPA_DRIVER_FLAGS_MGMT_TX_RANDOM_TA_CONNECTED	0x0000800000000000ULL
/** Driver supports better BSS reporting with sched_scan in connected mode */
#define WPA_DRIVER_FLAGS_SCHED_SCAN_RELATIVE_RSSI	0x0001000000000000ULL
/** Driver supports HE capabilities */
#define WPA_DRIVER_FLAGS_HE_CAPABILITIES	0x0002000000000000ULL
/** Driver supports FILS shared key offload */
#define WPA_DRIVER_FLAGS_FILS_SK_OFFLOAD	0x0004000000000000ULL
/** Driver supports all OCE STA specific mandatory features */
#define WPA_DRIVER_FLAGS_OCE_STA		0x0008000000000000ULL
/** Driver supports all OCE AP specific mandatory features */
#define WPA_DRIVER_FLAGS_OCE_AP			0x0010000000000000ULL
/**
 * Driver supports all OCE STA-CFON specific mandatory features only.
 * If a driver sets this bit but not the %WPA_DRIVER_FLAGS_OCE_AP, the
 * userspace shall assume that this driver may not support all OCE AP
 * functionality but can support only OCE STA-CFON functionality.
 */
#define WPA_DRIVER_FLAGS_OCE_STA_CFON		0x0020000000000000ULL
/** Driver supports MFP-optional in the connect command */
#define WPA_DRIVER_FLAGS_MFP_OPTIONAL		0x0040000000000000ULL
/** Driver is a self-managed regulatory device */
#define WPA_DRIVER_FLAGS_SELF_MANAGED_REGULATORY       0x0080000000000000ULL
/** Driver supports FTM responder functionality */
#define WPA_DRIVER_FLAGS_FTM_RESPONDER		0x0100000000000000ULL
/** Driver support 4-way handshake offload for WPA-Personal */
#define WPA_DRIVER_FLAGS_4WAY_HANDSHAKE_PSK	0x0200000000000000ULL
/** Driver supports a separate control port TX for EAPOL frames */
#define WPA_DRIVER_FLAGS_CONTROL_PORT		0x0400000000000000ULL
/** Driver supports VLAN offload */
#define WPA_DRIVER_FLAGS_VLAN_OFFLOAD		0x0800000000000000ULL
/** Driver supports UPDATE_FT_IES command */
#define WPA_DRIVER_FLAGS_UPDATE_FT_IES		0x1000000000000000ULL
/** Driver can correctly rekey PTKs without Extended Key ID */
#define WPA_DRIVER_FLAGS_SAFE_PTK0_REKEYS	0x2000000000000000ULL
/** Driver supports Beacon protection */
#define WPA_DRIVER_FLAGS_BEACON_PROTECTION	0x4000000000000000ULL
/** Driver supports Extended Key ID */
#define WPA_DRIVER_FLAGS_EXTENDED_KEY_ID	0x8000000000000000ULL
	u64 flags;

/** Driver supports a separate control port RX for EAPOL frames */
#define WPA_DRIVER_FLAGS2_CONTROL_PORT_RX	0x0000000000000001ULL
/** Driver supports TX status reports for EAPOL frames through control port */
#define WPA_DRIVER_FLAGS2_CONTROL_PORT_TX_STATUS 0x0000000000000002ULL
/** Driver supports secure LTF in AP mode */
#define WPA_DRIVER_FLAGS2_SEC_LTF_AP		0x0000000000000004ULL
/** Driver supports secure RTT measurement exchange in AP mode */
#define WPA_DRIVER_FLAGS2_SEC_RTT_AP		0x0000000000000008ULL
/**
 * Driver supports protection of range negotiation and measurement management
 * frames in AP mode
 */
#define WPA_DRIVER_FLAGS2_PROT_RANGE_NEG_AP	0x0000000000000010ULL
/** Driver supports Beacon frame TX rate configuration (HE rates) */
#define WPA_DRIVER_FLAGS2_BEACON_RATE_HE	0x0000000000000020ULL
/** Driver supports Beacon protection only in client mode */
#define WPA_DRIVER_FLAGS2_BEACON_PROTECTION_CLIENT 0x0000000000000040ULL
/** Driver supports Operating Channel Validation */
#define WPA_DRIVER_FLAGS2_OCV			0x0000000000000080ULL
/** Driver expects user space implementation of SME in AP mode */
#define WPA_DRIVER_FLAGS2_AP_SME		0x0000000000000100ULL
/** Driver handles SA Query procedures in AP mode */
#define WPA_DRIVER_FLAGS2_SA_QUERY_OFFLOAD_AP	0x0000000000000200ULL
/** Driver supports background radar/CAC detection */
#define WPA_DRIVER_FLAGS2_RADAR_BACKGROUND	0x0000000000000400ULL
/** Driver supports secure LTF in STA mode */
#define WPA_DRIVER_FLAGS2_SEC_LTF_STA		0x0000000000000800ULL
/** Driver supports secure RTT measurement exchange in STA mode */
#define WPA_DRIVER_FLAGS2_SEC_RTT_STA		0x0000000000001000ULL
/**
 * Driver supports protection of range negotiation and measurement management
 * frames in STA mode
 */
#define WPA_DRIVER_FLAGS2_PROT_RANGE_NEG_STA	0x0000000000002000ULL
/** Driver supports MLO in station/AP mode */
#define WPA_DRIVER_FLAGS2_MLO			0x0000000000004000ULL
/** Driver supports minimal scan request probe content  */
#define WPA_DRIVER_FLAGS2_SCAN_MIN_PREQ         0x0000000000008000ULL
/** Driver supports SAE authentication offload in STA mode */
#define WPA_DRIVER_FLAGS2_SAE_OFFLOAD_STA	0x0000000000010000ULL
/** Driver support AP_PSK authentication offload */
#define WPA_DRIVER_FLAGS2_4WAY_HANDSHAKE_AP_PSK	0x0000000000020000ULL
/** Driver supports OWE STA offload */
#define WPA_DRIVER_FLAGS2_OWE_OFFLOAD_STA	0x0000000000040000ULL
/** Driver supports OWE AP offload */
#define WPA_DRIVER_FLAGS2_OWE_OFFLOAD_AP	0x0000000000080000ULL
/** Driver support AP SAE authentication offload */
#define WPA_DRIVER_FLAGS2_SAE_OFFLOAD_AP	0x0000000000100000ULL
/** Driver supports TWT responder in HT and VHT modes */
#define WPA_DRIVER_FLAGS2_HT_VHT_TWT_RESPONDER	0x0000000000200000ULL
	u64 flags2;

#define FULL_AP_CLIENT_STATE_SUPP(drv_flags) \
	(drv_flags & WPA_DRIVER_FLAGS_FULL_AP_CLIENT_STATE)

	unsigned int wmm_ac_supported:1;

	unsigned int mac_addr_rand_scan_supported:1;
	unsigned int mac_addr_rand_sched_scan_supported:1;

	/** Maximum number of supported active probe SSIDs */
	int max_scan_ssids;

	/** Maximum number of supported active probe SSIDs for sched_scan */
	int max_sched_scan_ssids;

	/** Maximum number of supported scan plans for scheduled scan */
	unsigned int max_sched_scan_plans;

	/** Maximum interval in a scan plan. In seconds */
	u32 max_sched_scan_plan_interval;

	/** Maximum number of iterations in a single scan plan */
	u32 max_sched_scan_plan_iterations;

	/** Whether sched_scan (offloaded scanning) is supported */
	int sched_scan_supported;

	/** Maximum number of supported match sets for sched_scan */
	int max_match_sets;

	/**
	 * max_remain_on_chan - Maximum remain-on-channel duration in msec
	 */
	unsigned int max_remain_on_chan;

	/**
	 * max_stations - Maximum number of associated stations the driver
	 * supports in AP mode
	 */
	unsigned int max_stations;

	/**
	 * probe_resp_offloads - Bitmap of supported protocols by the driver
	 * for Probe Response offloading.
	 */
/** Driver Probe Response offloading support for WPS ver. 1 */
#define WPA_DRIVER_PROBE_RESP_OFFLOAD_WPS		0x00000001
/** Driver Probe Response offloading support for WPS ver. 2 */
#define WPA_DRIVER_PROBE_RESP_OFFLOAD_WPS2		0x00000002
/** Driver Probe Response offloading support for P2P */
#define WPA_DRIVER_PROBE_RESP_OFFLOAD_P2P		0x00000004
/** Driver Probe Response offloading support for IEEE 802.11u (Interworking) */
#define WPA_DRIVER_PROBE_RESP_OFFLOAD_INTERWORKING	0x00000008
	unsigned int probe_resp_offloads;

	unsigned int max_acl_mac_addrs;

	/**
	 * Number of supported concurrent channels
	 */
	unsigned int num_multichan_concurrent;

	/**
	 * extended_capa - extended capabilities in driver/device
	 *
	 * Must be allocated and freed by driver and the pointers must be
	 * valid for the lifetime of the driver, i.e., freed in deinit()
	 */
	const u8 *extended_capa, *extended_capa_mask;
	unsigned int extended_capa_len;

	struct wowlan_triggers wowlan_triggers;

/** Driver adds the DS Params Set IE in Probe Request frames */
#define WPA_DRIVER_FLAGS_DS_PARAM_SET_IE_IN_PROBES	0x00000001
/** Driver adds the WFA TPC IE in Probe Request frames */
#define WPA_DRIVER_FLAGS_WFA_TPC_IE_IN_PROBES		0x00000002
/** Driver handles quiet period requests */
#define WPA_DRIVER_FLAGS_QUIET				0x00000004
/**
 * Driver is capable of inserting the current TX power value into the body of
 * transmitted frames.
 * Background: Some Action frames include a TPC Report IE. This IE contains a
 * TX power field, which has to be updated by lower layers. One such Action
 * frame is Link Measurement Report (part of RRM). Another is TPC Report (part
 * of spectrum management). Note that this insertion takes place at a fixed
 * offset, namely the 6th byte in the Action frame body.
 */
#define WPA_DRIVER_FLAGS_TX_POWER_INSERTION		0x00000008
/**
 * Driver supports RRM. With this support, the driver will accept to use RRM in
 * (Re)Association Request frames, without supporting quiet period.
 */
#define WPA_DRIVER_FLAGS_SUPPORT_RRM			0x00000010

/** Driver supports setting the scan dwell time */
#define WPA_DRIVER_FLAGS_SUPPORT_SET_SCAN_DWELL		0x00000020
/** Driver supports Beacon Report Measurement */
#define WPA_DRIVER_FLAGS_SUPPORT_BEACON_REPORT		0x00000040

	u32 rrm_flags;

	/* Driver concurrency capabilities */
	unsigned int conc_capab;
	/* Maximum number of concurrent channels on 2.4 GHz */
	unsigned int max_conc_chan_2_4;
	/* Maximum number of concurrent channels on 5 GHz */
	unsigned int max_conc_chan_5_0;

	/* Maximum number of supported CSA counters */
	u16 max_csa_counters;

	/* Maximum number of supported AKM suites in commands */
	unsigned int max_num_akms;

	/* Maximum number of interfaces supported for MBSSID advertisement */
	unsigned int mbssid_max_interfaces;
	/* Maximum profile periodicity for enhanced MBSSID advertisement */
	unsigned int ema_max_periodicity;
};


struct hostapd_data;

enum guard_interval {
	GUARD_INTERVAL_0_4 = 1,
	GUARD_INTERVAL_0_8 = 2,
	GUARD_INTERVAL_1_6 = 3,
	GUARD_INTERVAL_3_2 = 4,
};

#define STA_DRV_DATA_TX_MCS BIT(0)
#define STA_DRV_DATA_RX_MCS BIT(1)
#define STA_DRV_DATA_TX_VHT_MCS BIT(2)
#define STA_DRV_DATA_RX_VHT_MCS BIT(3)
#define STA_DRV_DATA_TX_VHT_NSS BIT(4)
#define STA_DRV_DATA_RX_VHT_NSS BIT(5)
#define STA_DRV_DATA_TX_SHORT_GI BIT(6)
#define STA_DRV_DATA_RX_SHORT_GI BIT(7)
#define STA_DRV_DATA_LAST_ACK_RSSI BIT(8)
#define STA_DRV_DATA_CONN_TIME BIT(9)
#define STA_DRV_DATA_TX_HE_MCS BIT(10)
#define STA_DRV_DATA_RX_HE_MCS BIT(11)
#define STA_DRV_DATA_TX_HE_NSS BIT(12)
#define STA_DRV_DATA_RX_HE_NSS BIT(13)
#define STA_DRV_DATA_TX_HE_DCM BIT(14)
#define STA_DRV_DATA_RX_HE_DCM BIT(15)
#define STA_DRV_DATA_TX_HE_GI BIT(16)
#define STA_DRV_DATA_RX_HE_GI BIT(17)

struct hostap_sta_driver_data {
	unsigned long rx_packets, tx_packets;
	unsigned long long rx_bytes, tx_bytes;
	unsigned long long rx_airtime, tx_airtime;
	unsigned long long beacons_count;
	int bytes_64bit; /* whether 64-bit byte counters are supported */
	unsigned long current_tx_rate; /* in kbps */
	unsigned long current_rx_rate; /* in kbps */
	unsigned long inactive_msec;
	unsigned long connected_sec;
	unsigned long flags; /* bitfield of STA_DRV_DATA_* */
	unsigned long num_ps_buf_frames;
	unsigned long tx_retry_failed;
	unsigned long tx_retry_count;
	s8 last_ack_rssi;
	unsigned long backlog_packets;
	unsigned long backlog_bytes;
	unsigned long fcs_error_count;
	unsigned long beacon_loss_count;
	unsigned long expected_throughput;
	unsigned long rx_drop_misc;
	unsigned long rx_mpdus;
	int signal; /* dBm; or -WPA_INVALID_NOISE */
	u8 rx_hemcs;
	u8 tx_hemcs;
	u8 rx_vhtmcs;
	u8 tx_vhtmcs;
	u8 rx_mcs;
	u8 tx_mcs;
	u8 rx_he_nss;
	u8 tx_he_nss;
	u8 rx_vht_nss;
	u8 tx_vht_nss;
	s8 avg_signal; /* dBm */
	s8 avg_beacon_signal; /* dBm */
	s8 avg_ack_signal; /* dBm */
	enum guard_interval rx_guard_interval, tx_guard_interval;
	u8 rx_dcm, tx_dcm;
};

struct hostapd_sta_add_params {
	const u8 *addr;
	u16 aid;
	u16 capability;
	const u8 *supp_rates;
	size_t supp_rates_len;
	u16 listen_interval;
	const struct ieee80211_ht_capabilities *ht_capabilities;
	const struct ieee80211_vht_capabilities *vht_capabilities;
	int vht_opmode_enabled;
	u8 vht_opmode;
	const struct ieee80211_he_capabilities *he_capab;
	size_t he_capab_len;
	const struct ieee80211_he_6ghz_band_cap *he_6ghz_capab;
	const struct ieee80211_eht_capabilities *eht_capab;
	size_t eht_capab_len;
	u32 flags; /* bitmask of WPA_STA_* flags */
	u32 flags_mask; /* unset bits in flags */
#ifdef CONFIG_MESH
	enum mesh_plink_state plink_state;
	u16 peer_aid;
#endif /* CONFIG_MESH */
	int set; /* Set STA parameters instead of add */
	u8 qosinfo;
	const u8 *ext_capab;
	size_t ext_capab_len;
	const u8 *supp_channels;
	size_t supp_channels_len;
	const u8 *supp_oper_classes;
	size_t supp_oper_classes_len;
	int support_p2p_ps;

	bool mld_link_sta;
	s8 mld_link_id;
	const u8 *mld_link_addr;
};

struct mac_address {
	u8 addr[ETH_ALEN];
};

struct hostapd_acl_params {
	u8 acl_policy;
	unsigned int num_mac_acl;
	struct mac_address mac_acl[0];
};

struct wpa_init_params {
	void *global_priv;
	const u8 *bssid;
	const char *ifname;
	const char *driver_params;
	int use_pae_group_addr;
	char **bridge;
	size_t num_bridge;

	u8 *own_addr; /* buffer for writing own MAC address */
};


struct wpa_bss_params {
	/** Interface name (for multi-SSID/VLAN support) */
	const char *ifname;
	/** Whether IEEE 802.1X or WPA/WPA2 is enabled */
	int enabled;

	int wpa;
	int ieee802_1x;
	int wpa_group;
	int wpa_pairwise;
	int wpa_key_mgmt;
	int rsn_preauth;
	enum mfp_options ieee80211w;
};

#define WPA_STA_AUTHORIZED BIT(0)
#define WPA_STA_WMM BIT(1)
#define WPA_STA_SHORT_PREAMBLE BIT(2)
#define WPA_STA_MFP BIT(3)
#define WPA_STA_TDLS_PEER BIT(4)
#define WPA_STA_AUTHENTICATED BIT(5)
#define WPA_STA_ASSOCIATED BIT(6)

enum tdls_oper {
	TDLS_DISCOVERY_REQ,
	TDLS_SETUP,
	TDLS_TEARDOWN,
	TDLS_ENABLE_LINK,
	TDLS_DISABLE_LINK,
	TDLS_ENABLE,
	TDLS_DISABLE
};

enum wnm_oper {
	WNM_SLEEP_ENTER_CONFIRM,
	WNM_SLEEP_ENTER_FAIL,
	WNM_SLEEP_EXIT_CONFIRM,
	WNM_SLEEP_EXIT_FAIL,
	WNM_SLEEP_TFS_REQ_IE_ADD,   /* STA requests driver to add TFS req IE */
	WNM_SLEEP_TFS_REQ_IE_NONE,  /* STA requests empty TFS req IE */
	WNM_SLEEP_TFS_REQ_IE_SET,   /* AP requests driver to set TFS req IE for
				     * a STA */
	WNM_SLEEP_TFS_RESP_IE_ADD,  /* AP requests driver to add TFS resp IE
				     * for a STA */
	WNM_SLEEP_TFS_RESP_IE_NONE, /* AP requests empty TFS resp IE */
	WNM_SLEEP_TFS_RESP_IE_SET,  /* AP requests driver to set TFS resp IE
				     * for a STA */
	WNM_SLEEP_TFS_IE_DEL        /* AP delete the TFS IE */
};

/* enum smps_mode - SMPS mode definitions */
enum smps_mode {
	SMPS_AUTOMATIC,
	SMPS_OFF,
	SMPS_DYNAMIC,
	SMPS_STATIC,

	/* Keep last */
	SMPS_INVALID,
};

#define WPA_INVALID_NOISE 9999

/**
 * struct wpa_signal_info - Information about channel signal quality
 * @frequency: control frequency
 * @above_threshold: true if the above threshold was crossed
 *	(relevant for a CQM event)
 * @data: STA information
 * @current_noise: %WPA_INVALID_NOISE if not supported
 * @chanwidth: channel width
 * @center_frq1: center frequency for the first segment
 * @center_frq2: center frequency for the second segment (if relevant)
 */
struct wpa_signal_info {
	u32 frequency;
	int above_threshold;
	struct hostap_sta_driver_data data;
	int current_noise;
	enum chan_width chanwidth;
	int center_frq1;
	int center_frq2;
};

struct wpa_mlo_signal_info {
	u16 valid_links;
	struct wpa_signal_info links[MAX_NUM_MLD_LINKS];
};

/**
 * struct wpa_channel_info - Information about the current channel
 * @frequency: Center frequency of the primary 20 MHz channel
 * @chanwidth: Width of the current operating channel
 * @sec_channel: Location of the secondary 20 MHz channel (either +1 or -1).
 *	This field is only filled in when using a 40 MHz channel.
 * @center_frq1: Center frequency of frequency segment 0
 * @center_frq2: Center frequency of frequency segment 1 (for 80+80 channels)
 * @seg1_idx: Frequency segment 1 index when using a 80+80 channel. This is
 *	derived from center_frq2 for convenience.
 */
struct wpa_channel_info {
	u32 frequency;
	enum chan_width chanwidth;
	int sec_channel;
	int center_frq1;
	int center_frq2;
	u8 seg1_idx;
};

/**
 * struct beacon_data - Beacon data
 * @head: Head portion of Beacon frame (before TIM IE)
 * @tail: Tail portion of Beacon frame (after TIM IE)
 * @beacon_ies: Extra information element(s) to add into Beacon frames or %NULL
 * @proberesp_ies: Extra information element(s) to add into Probe Response
 *	frames or %NULL
 * @assocresp_ies: Extra information element(s) to add into (Re)Association
 *	Response frames or %NULL
 * @probe_resp: Probe Response frame template
 * @head_len: Length of @head
 * @tail_len: Length of @tail
 * @beacon_ies_len: Length of beacon_ies in octets
 * @proberesp_ies_len: Length of proberesp_ies in octets
 * @proberesp_ies_len: Length of proberesp_ies in octets
 * @probe_resp_len: Length of probe response template (@probe_resp)
 */
struct beacon_data {
	u8 *head, *tail;
	u8 *beacon_ies;
	u8 *proberesp_ies;
	u8 *assocresp_ies;
	u8 *probe_resp;

	size_t head_len, tail_len;
	size_t beacon_ies_len;
	size_t proberesp_ies_len;
	size_t assocresp_ies_len;
	size_t probe_resp_len;
};

/**
 * struct csa_settings - Settings for channel switch command
 * @cs_count: Count in Beacon frames (TBTT) to perform the switch
 * @block_tx: 1 - block transmission for CSA period
 * @freq_params: Next channel frequency parameter
 * @beacon_csa: Beacon/probe resp/asooc resp info for CSA period
 * @beacon_after: Next beacon/probe resp/asooc resp info
 * @counter_offset_beacon: Offset to the count field in beacon's tail
 * @counter_offset_presp: Offset to the count field in probe resp.
 * @punct_bitmap - Preamble puncturing bitmap
 * @link_id: Link ID to determine the link for MLD; -1 for non-MLD
 * @ubpr: Unsolicited broadcast Probe Response frame data
 */
struct csa_settings {
	u8 cs_count;
	u8 block_tx;

	struct hostapd_freq_params freq_params;
	struct beacon_data beacon_csa;
	struct beacon_data beacon_after;

	u16 counter_offset_beacon[2];
	u16 counter_offset_presp[2];

	u16 punct_bitmap;
	int link_id;

	struct unsol_bcast_probe_resp ubpr;
};

/**
 * struct cca_settings - Settings for color switch command
 * @cca_count: Count in Beacon frames (TBTT) to perform the switch
 * @cca_color: The new color that we are switching to
 * @beacon_cca: Beacon/Probe Response/(Re)Association Response frame info for
 * color switch period
 * @beacon_after: Next Beacon/Probe Response/(Re)Association Response frame info
 * @counter_offset_beacon: Offset to the count field in Beacon frame tail
 * @counter_offset_presp: Offset to the count field in Probe Response frame
 * @ubpr: Unsolicited broadcast Probe Response frame data
 * @link_id: If >= 0 indicates the link of the AP MLD to configure
 */
struct cca_settings {
	u8 cca_count;
	u8 cca_color;

	struct beacon_data beacon_cca;
	struct beacon_data beacon_after;

	u16 counter_offset_beacon;
	u16 counter_offset_presp;

	struct unsol_bcast_probe_resp ubpr;

	int link_id;
};

/* TDLS peer capabilities for send_tdls_mgmt() */
enum tdls_peer_capability {
	TDLS_PEER_HT = BIT(0),
	TDLS_PEER_VHT = BIT(1),
	TDLS_PEER_WMM = BIT(2),
	TDLS_PEER_HE = BIT(3),
};

/* valid info in the wmm_params struct */
enum wmm_params_valid_info {
	WMM_PARAMS_UAPSD_QUEUES_INFO = BIT(0),
};

/**
 * struct wmm_params - WMM parameterss configured for this association
 * @info_bitmap: Bitmap of valid wmm_params info; indicates what fields
 *	of the struct contain valid information.
 * @uapsd_queues: Bitmap of ACs configured for uapsd (valid only if
 *	%WMM_PARAMS_UAPSD_QUEUES_INFO is set)
 */
struct wmm_params {
	u8 info_bitmap;
	u8 uapsd_queues;
};

#ifdef CONFIG_MACSEC
struct macsec_init_params {
	bool always_include_sci;
	bool use_es;
	bool use_scb;
};
#endif /* CONFIG_MACSEC */

enum drv_br_port_attr {
	DRV_BR_PORT_ATTR_PROXYARP,
	DRV_BR_PORT_ATTR_HAIRPIN_MODE,
	DRV_BR_PORT_ATTR_MCAST2UCAST,
};

enum drv_br_net_param {
	DRV_BR_NET_PARAM_GARP_ACCEPT,
	DRV_BR_MULTICAST_SNOOPING,
};

struct drv_acs_params {
	/* Selected mode (HOSTAPD_MODE_*) */
	enum hostapd_hw_mode hw_mode;

	/* Indicates whether HT is enabled */
	int ht_enabled;

	/* Indicates whether HT40 is enabled */
	int ht40_enabled;

	/* Indicates whether VHT is enabled */
	int vht_enabled;

	/* Configured ACS channel width */
	u16 ch_width;

	/* ACS frequency list info */
	const int *freq_list;

	/* Indicates whether EDMG is enabled */
	int edmg_enabled;

	/* Indicates whether EHT is enabled */
	bool eht_enabled;

	/* Indicates the link if MLO case; -1 otherwise */
	int link_id;
};

struct wpa_bss_trans_info {
	u8 mbo_transition_reason;
	u8 n_candidates;
	u8 *bssid;
};

struct wpa_bss_candidate_info {
	u8 num;
	struct candidate_list {
		u8 bssid[ETH_ALEN];
		u8 is_accept;
		u32 reject_reason;
	} *candidates;
};

struct wpa_pmkid_params {
	const u8 *bssid;
	const u8 *ssid;
	size_t ssid_len;
	const u8 *fils_cache_id;
	const u8 *pmkid;
	const u8 *pmk;
	size_t pmk_len;
	u32 pmk_lifetime;
	u8 pmk_reauth_threshold;
};

/* Mask used to specify which connection parameters have to be updated */
enum wpa_drv_update_connect_params_mask {
	WPA_DRV_UPDATE_ASSOC_IES	= BIT(0),
	WPA_DRV_UPDATE_FILS_ERP_INFO	= BIT(1),
	WPA_DRV_UPDATE_AUTH_TYPE	= BIT(2),
};

/**
 * struct external_auth - External authentication trigger parameters
 *
 * These are used across the external authentication request and event
 * interfaces.
 * @action: Action type / trigger for external authentication. Only significant
 *	for the event interface.
 * @bssid: BSSID of the peer with which the authentication has to happen. Used
 *	by both the request and event interface.
 * @ssid: SSID of the AP. Used by both the request and event interface.
 * @ssid_len: SSID length in octets.
 * @key_mgmt_suite: AKM suite of the respective authentication. Optional for
 *	the request interface.
 * @status: Status code, %WLAN_STATUS_SUCCESS for successful authentication,
 *	use %WLAN_STATUS_UNSPECIFIED_FAILURE if wpa_supplicant cannot give
 *	the real status code for failures. Used only for the request interface
 *	from user space to the driver.
 * @pmkid: Generated PMKID as part of external auth exchange (e.g., SAE).
 * @mld_addr: AP's MLD address or %NULL if MLO is not used
 */
struct external_auth {
	enum {
		EXT_AUTH_START,
		EXT_AUTH_ABORT,
	} action;
	const u8 *bssid;
	const u8 *ssid;
	size_t ssid_len;
	unsigned int key_mgmt_suite;
	u16 status;
	const u8 *pmkid;
	const u8 *mld_addr;
};

#define WPAS_MAX_PASN_PEERS 10

enum pasn_status {
	PASN_STATUS_SUCCESS = 0,
	PASN_STATUS_FAILURE = 1,
};

/**
 * struct pasn_peer - PASN peer parameters
 *
 * Used to process the PASN authentication event from the driver to
 * userspace and to send a response back.
 * @own_addr: Own MAC address specified by the driver to use for PASN
 *	handshake.
 * @peer_addr: MAC address of the peer with which PASN authentication is to be
 *	performed.
 * @network_id: Unique id for the network.
 *	This identifier is used as a unique identifier for each network
 *	block when using the control interface. Each network is allocated an
 *	id when it is being created, either when reading the configuration
 *	file or when a new network is added through the control interface.
 * @akmp: Authentication key management protocol type supported.
 * @cipher: Cipher suite.
 * @group: Finite cyclic group. Default group used is 19 (ECC).
 * @ltf_keyseed_required: Indicates whether LTF keyseed generation is required
 * @status: PASN response status, %PASN_STATUS_SUCCESS for successful
 *	authentication, use %PASN_STATUS_FAILURE if PASN authentication
 *	fails or if wpa_supplicant fails to set the security ranging context to
 *	the driver
 */
struct pasn_peer {
	u8 own_addr[ETH_ALEN];
	u8 peer_addr[ETH_ALEN];
	int network_id;
	int akmp;
	int cipher;
	int group;
	bool ltf_keyseed_required;
	enum pasn_status status;
};

/**
 * struct pasn_auth - PASN authentication trigger parameters
 *
 * These are used across the PASN authentication event from the driver to
 * userspace and to send a response to it.
 * @action: Action type. Only significant for the event interface.
 * @num_peers: The number of peers for which the PASN handshake is requested
 *	for.
 * @peer: Holds the peer details.
 */
struct pasn_auth {
	enum {
		PASN_ACTION_AUTH,
		PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT,
	} action;
	unsigned int num_peers;
	struct pasn_peer peer[WPAS_MAX_PASN_PEERS];
};

/**
 * struct secure_ranging_params - Parameters required to set secure ranging
 *	context for a peer.
 *
 * @action: Add or delete a security context to the driver.
 * @own_addr: Own MAC address used during key derivation.
 * @peer_addr: Address of the peer device.
 * @cipher: Cipher suite.
 * @tk_len: Length of temporal key.
 * @tk: Temporal key buffer.
 * @ltf_keyseed_len: Length of LTF keyseed.
 * @ltf_keyeed: LTF keyseed buffer.
 */
struct secure_ranging_params {
	u32 action;
	const u8 *own_addr;
	const u8 *peer_addr;
	u32 cipher;
	u8 tk_len;
	const u8 *tk;
	u8 ltf_keyseed_len;
	const u8 *ltf_keyseed;
};

/* enum nested_attr - Used to specify if subcommand uses nested attributes */
enum nested_attr {
	NESTED_ATTR_NOT_USED = 0,
	NESTED_ATTR_USED = 1,
	NESTED_ATTR_UNSPECIFIED = 2,
};

/* Preferred channel list information */

/* GO role */
#define WEIGHTED_PCL_GO BIT(0)
/* P2P Client role */
#define WEIGHTED_PCL_CLI BIT(1)
/* Must be considered for operating channel */
#define WEIGHTED_PCL_MUST_CONSIDER BIT(2)
/* Should be excluded in GO negotiation */
#define WEIGHTED_PCL_EXCLUDE BIT(3)

/* Preferred channel list with weight */
struct weighted_pcl {
	u32 freq; /* MHz */
	u8 weight;
	u32 flag; /* bitmap for WEIGHTED_PCL_* */
};

struct driver_sta_mlo_info {
	bool default_map;
	u16 req_links; /* bitmap of requested link IDs */
	u16 valid_links; /* bitmap of accepted link IDs */
	u8 assoc_link_id;
	u8 ap_mld_addr[ETH_ALEN];
	struct {
		u8 addr[ETH_ALEN];
		u8 bssid[ETH_ALEN];
		unsigned int freq;
		struct t2lm_mapping t2lmap;
	} links[MAX_NUM_MLD_LINKS];
};

/**
 * struct wpa_driver_ops - Driver interface API definition
 *
 * This structure defines the API that each driver interface needs to implement
 * for core wpa_supplicant code. All driver specific functionality is captured
 * in this wrapper.
 */
struct wpa_driver_ops {
	/** Name of the driver interface */
	const char *name;
	/** One line description of the driver interface */
	const char *desc;

	/**
	 * get_bssid - Get the current BSSID
	 * @priv: private driver interface data
	 * @bssid: buffer for BSSID (ETH_ALEN = 6 bytes)
	 *
	 * Returns: 0 on success, -1 on failure
	 *
	 * Query kernel driver for the current BSSID and copy it to bssid.
	 * Setting bssid to 00:00:00:00:00:00 is recommended if the STA is not
	 * associated.
	 */
	int (*get_bssid)(void *priv, u8 *bssid);

	/**
	 * get_ssid - Get the current SSID
	 * @priv: private driver interface data
	 * @ssid: buffer for SSID (at least 32 bytes)
	 *
	 * Returns: Length of the SSID on success, -1 on failure
	 *
	 * Query kernel driver for the current SSID and copy it to ssid.
	 * Returning zero is recommended if the STA is not associated.
	 *
	 * Note: SSID is an array of octets, i.e., it is not nul terminated and
	 * can, at least in theory, contain control characters (including nul)
	 * and as such, should be processed as binary data, not a printable
	 * string.
	 */
	int (*get_ssid)(void *priv, u8 *ssid);

	/**
	 * set_key - Configure encryption key
	 * @priv: private driver interface data
	 * @params: Key parameters
	 * Returns: 0 on success, -1 on failure
	 *
	 * Configure the given key for the kernel driver. If the driver
	 * supports separate individual keys (4 default keys + 1 individual),
	 * addr can be used to determine whether the key is default or
	 * individual. If only 4 keys are supported, the default key with key
	 * index 0 is used as the individual key. STA must be configured to use
	 * it as the default Tx key (set_tx is set) and accept Rx for all the
	 * key indexes. In most cases, WPA uses only key indexes 1 and 2 for
	 * broadcast keys, so key index 0 is available for this kind of
	 * configuration.
	 *
	 * Please note that TKIP keys include separate TX and RX MIC keys and
	 * some drivers may expect them in different order than wpa_supplicant
	 * is using. If the TX/RX keys are swapped, all TKIP encrypted packets
	 * will trigger Michael MIC errors. This can be fixed by changing the
	 * order of MIC keys by swapping the bytes 16..23 and 24..31 of the key
	 * in driver_*.c set_key() implementation, see driver_ndis.c for an
	 * example on how this can be done.
	 */
	int (*set_key)(void *priv, struct wpa_driver_set_key_params *params);

	/**
	 * init - Initialize driver interface
	 * @ctx: context to be used when calling wpa_supplicant functions,
	 * e.g., wpa_supplicant_event()
	 * @ifname: interface name, e.g., wlan0
	 *
	 * Returns: Pointer to private data, %NULL on failure
	 *
	 * Initialize driver interface, including event processing for kernel
	 * driver events (e.g., associated, scan results, Michael MIC failure).
	 * This function can allocate a private configuration data area for
	 * @ctx, file descriptor, interface name, etc. information that may be
	 * needed in future driver operations. If this is not used, non-NULL
	 * value will need to be returned because %NULL is used to indicate
	 * failure. The returned value will be used as 'void *priv' data for
	 * all other driver_ops functions.
	 *
	 * The main event loop (eloop.c) of wpa_supplicant can be used to
	 * register callback for read sockets (eloop_register_read_sock()).
	 *
	 * See below for more information about events and
	 * wpa_supplicant_event() function.
	 */
	void * (*init)(void *ctx, const char *ifname);

	/**
	 * deinit - Deinitialize driver interface
	 * @priv: private driver interface data from init()
	 *
	 * Shut down driver interface and processing of driver events. Free
	 * private data buffer if one was allocated in init() handler.
	 */
	void (*deinit)(void *priv);

	/**
	 * set_param - Set driver configuration parameters
	 * @priv: private driver interface data from init()
	 * @param: driver specific configuration parameters
	 *
	 * Returns: 0 on success, -1 on failure
	 *
	 * Optional handler for notifying driver interface about configuration
	 * parameters (driver_param).
	 */
	int (*set_param)(void *priv, const char *param);

	/**
	 * set_countermeasures - Enable/disable TKIP countermeasures
	 * @priv: private driver interface data
	 * @enabled: 1 = countermeasures enabled, 0 = disabled
	 *
	 * Returns: 0 on success, -1 on failure
	 *
	 * Configure TKIP countermeasures. When these are enabled, the driver
	 * should drop all received and queued frames that are using TKIP.
	 */
	int (*set_countermeasures)(void *priv, int enabled);

	/**
	 * deauthenticate - Request driver to deauthenticate
	 * @priv: private driver interface data
	 * @addr: peer address (BSSID of the AP)
	 * @reason_code: 16-bit reason code to be sent in the deauthentication
	 *	frame
	 *
	 * Returns: 0 on success, -1 on failure
	 */
	int (*deauthenticate)(void *priv, const u8 *addr, u16 reason_code);

	/**
	 * associate - Request driver to associate
	 * @priv: private driver interface data
	 * @params: association parameters
	 *
	 * Returns: 0 on success, -1 on failure
	 */
	int (*associate)(void *priv,
			 struct wpa_driver_associate_params *params);

	/**
	 * add_pmkid - Add PMKSA cache entry to the driver
	 * @priv: private driver interface data
	 * @params: PMKSA parameters
	 *
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function is called when a new PMK is received, as a result of
	 * either normal authentication or RSN pre-authentication. The PMKSA
	 * parameters are either a set of bssid, pmkid, and pmk; or a set of
	 * ssid, fils_cache_id, pmkid, and pmk.
	 *
	 * If the driver generates RSN IE, i.e., it does not use wpa_ie in
	 * associate(), add_pmkid() can be used to add new PMKSA cache entries
	 * in the driver. If the driver uses wpa_ie from wpa_supplicant, this
	 * driver_ops function does not need to be implemented. Likewise, if
	 * the driver does not support WPA, this function is not needed.
	 */
	int (*add_pmkid)(void *priv, struct wpa_pmkid_params *params);

	/**
	 * remove_pmkid - Remove PMKSA cache entry to the driver
	 * @priv: private driver interface data
	 * @params: PMKSA parameters
	 *
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function is called when the supplicant drops a PMKSA cache
	 * entry for any reason. The PMKSA parameters are either a set of
	 * bssid and pmkid; or a set of ssid, fils_cache_id, and pmkid.
	 *
	 * If the driver generates RSN IE, i.e., it does not use wpa_ie in
	 * associate(), remove_pmkid() can be used to synchronize PMKSA caches
	 * between the driver and wpa_supplicant. If the driver uses wpa_ie
	 * from wpa_supplicant, this driver_ops function does not need to be
	 * implemented. Likewise, if the driver does not support WPA, this
	 * function is not needed.
	 */
	int (*remove_pmkid)(void *priv, struct wpa_pmkid_params *params);

	/**
	 * flush_pmkid - Flush PMKSA cache
	 * @priv: private driver interface data
	 *
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function is called when the supplicant drops all PMKSA cache
	 * entries for any reason.
	 *
	 * If the driver generates RSN IE, i.e., it does not use wpa_ie in
	 * associate(), remove_pmkid() can be used to synchronize PMKSA caches
	 * between the driver and wpa_supplicant. If the driver uses wpa_ie
	 * from wpa_supplicant, this driver_ops function does not need to be
	 * implemented. Likewise, if the driver does not support WPA, this
	 * function is not needed.
	 */
	int (*flush_pmkid)(void *priv);

	/**
	 * get_capa - Get driver capabilities
	 * @priv: private driver interface data
	 *
	 * Returns: 0 on success, -1 on failure
	 *
	 * Get driver/firmware/hardware capabilities.
	 */
	int (*get_capa)(void *priv, struct wpa_driver_capa *capa);

	/**
	 * poll - Poll driver for association information
	 * @priv: private driver interface data
	 *
	 * This is an optional callback that can be used when the driver does
	 * not provide event mechanism for association events. This is called
	 * when receiving WPA/RSN EAPOL-Key messages that require association
	 * information. The driver interface is supposed to generate associnfo
	 * event before returning from this callback function. In addition, the
	 * driver interface should generate an association event after having
	 * sent out associnfo.
	 */
	void (*poll)(void *priv);

	/**
	 * get_ifindex - Get interface index
	 * @priv: private driver interface data
	 *
	 * Returns: Interface index
	 */
	unsigned int (*get_ifindex)(void *priv);

	/**
	 * get_ifname - Get interface name
	 * @priv: private driver interface data
	 *
	 * Returns: Pointer to the interface name. This can differ from the
	 * interface name used in init() call. Init() is called first.
	 *
	 * This optional function can be used to allow the driver interface to
	 * replace the interface name with something else, e.g., based on an
	 * interface mapping from a more descriptive name.
	 */
	const char * (*get_ifname)(void *priv);

	/**
	 * get_mac_addr - Get own MAC address
	 * @priv: private driver interface data
	 *
	 * Returns: Pointer to own MAC address or %NULL on failure
	 *
	 * This optional function can be used to get the own MAC address of the
	 * device from the driver interface code. This is only needed if the
	 * l2_packet implementation for the OS does not provide easy access to
	 * a MAC address. */
	const u8 * (*get_mac_addr)(void *priv);

	/**
	 * set_operstate - Sets device operating state to DORMANT or UP
	 * @priv: private driver interface data
	 * @state: 0 = dormant, 1 = up
	 * Returns: 0 on success, -1 on failure
	 *
	 * This is an optional function that can be used on operating systems
	 * that support a concept of controlling network device state from user
	 * space applications. This function, if set, gets called with
	 * state = 1 when authentication has been completed and with state = 0
	 * when connection is lost.
	 */
	int (*set_operstate)(void *priv, int state);

	/**
	 * mlme_setprotection - MLME-SETPROTECTION.request primitive
	 * @priv: Private driver interface data
	 * @addr: Address of the station for which to set protection (may be
	 * %NULL for group keys)
	 * @protect_type: MLME_SETPROTECTION_PROTECT_TYPE_*
	 * @key_type: MLME_SETPROTECTION_KEY_TYPE_*
	 * Returns: 0 on success, -1 on failure
	 *
	 * This is an optional function that can be used to set the driver to
	 * require protection for Tx and/or Rx frames. This uses the layer
	 * interface defined in IEEE 802.11i-2004 clause 10.3.22.1
	 * (MLME-SETPROTECTION.request). Many drivers do not use explicit
	 * set protection operation; instead, they set protection implicitly
	 * based on configured keys.
	 */
	int (*mlme_setprotection)(void *priv, const u8 *addr, int protect_type,
				  int key_type);

	/**
	 * get_hw_feature_data - Get hardware support data (channels and rates)
	 * @priv: Private driver interface data
	 * @num_modes: Variable for returning the number of returned modes
	 * flags: Variable for returning hardware feature flags
	 * @dfs: Variable for returning DFS region (HOSTAPD_DFS_REGION_*)
	 * Returns: Pointer to allocated hardware data on success or %NULL on
	 * failure. Caller is responsible for freeing this.
	 */
	struct hostapd_hw_modes * (*get_hw_feature_data)(void *priv,
							 u16 *num_modes,
							 u16 *flags, u8 *dfs);

	/**
	 * send_mlme - Send management frame from MLME
	 * @priv: Private driver interface data
	 * @data: IEEE 802.11 management frame with IEEE 802.11 header
	 * @data_len: Size of the management frame
	 * @noack: Do not wait for this frame to be acked (disable retries)
	 * @freq: Frequency (in MHz) to send the frame on, or 0 to let the
	 * driver decide
	 * @csa_offs: Array of CSA offsets or %NULL
	 * @csa_offs_len: Number of elements in csa_offs
	 * @no_encrypt: Do not encrypt frame even if appropriate key exists
	 *	(used only for testing purposes)
	 * @wait: Time to wait off-channel for a response (in ms), or zero
	 * @link_id: Link ID to use for TX, or -1 if not set
	 * Returns: 0 on success, -1 on failure
	 */
	int (*send_mlme)(void *priv, const u8 *data, size_t data_len,
			 int noack, unsigned int freq, const u16 *csa_offs,
			 size_t csa_offs_len, int no_encrypt,
			 unsigned int wait, int link_id);

	/**
	 * update_ft_ies - Update FT (IEEE 802.11r) IEs
	 * @priv: Private driver interface data
	 * @md: Mobility domain (2 octets) (also included inside ies)
	 * @ies: FT IEs (MDIE, FTIE, ...) or %NULL to remove IEs
	 * @ies_len: Length of FT IEs in bytes
	 * Returns: 0 on success, -1 on failure
	 *
	 * The supplicant uses this callback to let the driver know that keying
	 * material for FT is available and that the driver can use the
	 * provided IEs in the next message in FT authentication sequence.
	 *
	 * This function is only needed for driver that support IEEE 802.11r
	 * (Fast BSS Transition).
	 */
	int (*update_ft_ies)(void *priv, const u8 *md, const u8 *ies,
			     size_t ies_len);

	/**
	 * get_scan_results - Fetch the latest scan results
	 * @priv: Private driver interface data
	 * @bssid: Return results only for the specified BSSID, %NULL for all
	 *
	 * Returns: Allocated buffer of scan results (caller is responsible for
	 * freeing the data structure) on success, NULL on failure
	 */
	struct wpa_scan_results * (*get_scan_results)(void *priv,
						      const u8 *bssid);

	/**
	 * get_scan_results2 - Fetch the latest scan results
	 * @priv: private driver interface data
	 *
	 * Returns: Allocated buffer of scan results (caller is responsible for
	 * freeing the data structure) on success, NULL on failure
	 */
	 struct wpa_scan_results * (*get_scan_results2)(void *priv);

	/**
	 * set_country - Set country
	 * @priv: Private driver interface data
	 * @alpha2: country to which to switch to
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function is for drivers which support some form
	 * of setting a regulatory domain.
	 */
	int (*set_country)(void *priv, const char *alpha2);

	/**
	 * get_country - Get country
	 * @priv: Private driver interface data
	 * @alpha2: Buffer for returning country code (at least 3 octets)
	 * Returns: 0 on success, -1 on failure
	 */
	int (*get_country)(void *priv, char *alpha2);

	/**
	 * global_init - Global driver initialization
	 * @ctx: wpa_global pointer
	 * Returns: Pointer to private data (global), %NULL on failure
	 *
	 * This optional function is called to initialize the driver wrapper
	 * for global data, i.e., data that applies to all interfaces. If this
	 * function is implemented, global_deinit() will also need to be
	 * implemented to free the private data. The driver will also likely
	 * use init2() function instead of init() to get the pointer to global
	 * data available to per-interface initializer.
	 */
	void * (*global_init)(void *ctx);

	/**
	 * global_deinit - Global driver deinitialization
	 * @priv: private driver global data from global_init()
	 *
	 * Terminate any global driver related functionality and free the
	 * global data structure.
	 */
	void (*global_deinit)(void *priv);

	/**
	 * init2 - Initialize driver interface (with global data)
	 * @ctx: context to be used when calling wpa_supplicant functions,
	 * e.g., wpa_supplicant_event()
	 * @ifname: interface name, e.g., wlan0
	 * @global_priv: private driver global data from global_init()
	 * Returns: Pointer to private data, %NULL on failure
	 *
	 * This function can be used instead of init() if the driver wrapper
	 * uses global data.
	 */
	void * (*init2)(void *ctx, const char *ifname, void *global_priv);

	/**
	 * get_interfaces - Get information about available interfaces
	 * @global_priv: private driver global data from global_init()
	 * Returns: Allocated buffer of interface information (caller is
	 * responsible for freeing the data structure) on success, NULL on
	 * failure
	 */
	struct wpa_interface_info * (*get_interfaces)(void *global_priv);

	/**
	 * scan2 - Request the driver to initiate scan
	 * @priv: private driver interface data
	 * @params: Scan parameters
	 *
	 * Returns: 0 on success, -1 on failure
	 *
	 * Once the scan results are ready, the driver should report scan
	 * results event for wpa_supplicant which will eventually request the
	 * results with wpa_driver_get_scan_results2().
	 */
	int (*scan2)(void *priv, struct wpa_driver_scan_params *params);

	/**
	 * authenticate - Request driver to authenticate
	 * @priv: private driver interface data
	 * @params: authentication parameters
	 * Returns: 0 on success, -1 on failure
	 *
	 * This is an optional function that can be used with drivers that
	 * support separate authentication and association steps, i.e., when
	 * wpa_supplicant can act as the SME. If not implemented, associate()
	 * function is expected to take care of IEEE 802.11 authentication,
	 * too.
	 */
	int (*authenticate)(void *priv,
			    struct wpa_driver_auth_params *params);

	/**
	 * set_ap - Set Beacon and Probe Response information for AP mode
	 * @priv: Private driver interface data
	 * @params: Parameters to use in AP mode
	 *
	 * This function is used to configure Beacon template and/or extra IEs
	 * to add for Beacon and Probe Response frames for the driver in
	 * AP mode. The driver is responsible for building the full Beacon
	 * frame by concatenating the head part with TIM IE generated by the
	 * driver/firmware and finishing with the tail part. Depending on the
	 * driver architectue, this can be done either by using the full
	 * template or the set of additional IEs (e.g., WPS and P2P IE).
	 * Similarly, Probe Response processing depends on the driver design.
	 * If the driver (or firmware) takes care of replying to Probe Request
	 * frames, the extra IEs provided here needs to be added to the Probe
	 * Response frames.
	 *
	 * Returns: 0 on success, -1 on failure
	 */
	int (*set_ap)(void *priv, struct wpa_driver_ap_params *params);

	/**
	 * set_acl - Set ACL in AP mode
	 * @priv: Private driver interface data
	 * @params: Parameters to configure ACL
	 * Returns: 0 on success, -1 on failure
	 *
	 * This is used only for the drivers which support MAC address ACL.
	 */
	int (*set_acl)(void *priv, struct hostapd_acl_params *params);

	/**
	 * hapd_init - Initialize driver interface (hostapd only)
	 * @hapd: Pointer to hostapd context
	 * @params: Configuration for the driver wrapper
	 * Returns: Pointer to private data, %NULL on failure
	 *
	 * This function is used instead of init() or init2() when the driver
	 * wrapper is used with hostapd.
	 */
	void * (*hapd_init)(struct hostapd_data *hapd,
			    struct wpa_init_params *params);

	/**
	 * hapd_deinit - Deinitialize driver interface (hostapd only)
	 * @priv: Private driver interface data from hapd_init()
	 */
	void (*hapd_deinit)(void *priv);

	/**
	 * set_ieee8021x - Enable/disable IEEE 802.1X support (AP only)
	 * @priv: Private driver interface data
	 * @params: BSS parameters
	 * Returns: 0 on success, -1 on failure
	 *
	 * This is an optional function to configure the kernel driver to
	 * enable/disable IEEE 802.1X support and set WPA/WPA2 parameters. This
	 * can be left undefined (set to %NULL) if IEEE 802.1X support is
	 * always enabled and the driver uses set_ap() to set WPA/RSN IE
	 * for Beacon frames.
	 *
	 * DEPRECATED - use set_ap() instead
	 */
	int (*set_ieee8021x)(void *priv, struct wpa_bss_params *params);

	/**
	 * set_privacy - Enable/disable privacy (AP only)
	 * @priv: Private driver interface data
	 * @enabled: 1 = privacy enabled, 0 = disabled
	 * Returns: 0 on success, -1 on failure
	 *
	 * This is an optional function to configure privacy field in the
	 * kernel driver for Beacon frames. This can be left undefined (set to
	 * %NULL) if the driver uses the Beacon template from set_ap().
	 *
	 * DEPRECATED - use set_ap() instead
	 */
	int (*set_privacy)(void *priv, int enabled);

	/**
	 * get_seqnum - Fetch the current TSC/packet number (AP only)
	 * @ifname: The interface name (main or virtual)
	 * @priv: Private driver interface data
	 * @addr: MAC address of the station or %NULL for group keys
	 * @idx: Key index
	 * @link_id: Link ID for a group key, or -1 if not set
	 * @seq: Buffer for returning the latest used TSC/packet number
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function is used to fetch the last used TSC/packet number for
	 * a TKIP, CCMP, GCMP, or BIP/IGTK key. It is mainly used with group
	 * keys, so there is no strict requirement on implementing support for
	 * unicast keys (i.e., addr != %NULL).
	 */
	int (*get_seqnum)(const char *ifname, void *priv, const u8 *addr,
			  int idx, int link_id, u8 *seq);

	/**
	 * flush - Flush all association stations (AP only)
	 * @priv: Private driver interface data
	 * @link_id: In case of MLO, valid link ID on which all associated
	 *	stations will be flushed, -1 otherwise.
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function requests the driver to disassociate all associated
	 * stations. This function does not need to be implemented if the
	 * driver does not process association frames internally.
	 */
	int (*flush)(void *priv, int link_id);

	/**
	 * set_generic_elem - Add IEs into Beacon/Probe Response frames (AP)
	 * @priv: Private driver interface data
	 * @elem: Information elements
	 * @elem_len: Length of the elem buffer in octets
	 * Returns: 0 on success, -1 on failure
	 *
	 * This is an optional function to add information elements in the
	 * kernel driver for Beacon and Probe Response frames. This can be left
	 * undefined (set to %NULL) if the driver uses the Beacon template from
	 * set_ap().
	 *
	 * DEPRECATED - use set_ap() instead
	 */
	int (*set_generic_elem)(void *priv, const u8 *elem, size_t elem_len);

	/**
	 * read_sta_data - Fetch station data
	 * @priv: Private driver interface data
	 * @data: Buffer for returning station information
	 * @addr: MAC address of the station
	 * Returns: 0 on success, -1 on failure
	 */
	int (*read_sta_data)(void *priv, struct hostap_sta_driver_data *data,
			     const u8 *addr);

	/**
	 * tx_control_port - Send a frame over the 802.1X controlled port
	 * @priv: Private driver interface data
	 * @dest: Destination MAC address
	 * @proto: Ethertype in host byte order
	 * @buf: Frame payload starting from IEEE 802.1X header
	 * @len: Frame payload length
	 * @no_encrypt: Do not encrypt frame
	 * @link_id: Link ID to use for TX, or -1 if not set
	 *
	 * Returns 0 on success, else an error
	 *
	 * This is like a normal Ethernet send except that the driver is aware
	 * (by other means than the Ethertype) that this frame is special,
	 * and more importantly it gains an ordering between the transmission of
	 * the frame and other driver management operations such as key
	 * installations. This can be used to work around known limitations in
	 * IEEE 802.11 protocols such as race conditions between rekeying 4-way
	 * handshake message 4/4 and a PTK being overwritten.
	 *
	 * This function is only used for a given interface if the driver
	 * instance reports WPA_DRIVER_FLAGS_CONTROL_PORT capability. Otherwise,
	 * API users will fall back to sending the frame via a normal socket.
	 */
	int (*tx_control_port)(void *priv, const u8 *dest,
			       u16 proto, const u8 *buf, size_t len,
			       int no_encrypt, int link_id);

	/**
	 * hapd_send_eapol - Send an EAPOL packet (AP only)
	 * @priv: private driver interface data
	 * @addr: Destination MAC address
	 * @data: EAPOL packet starting with IEEE 802.1X header
	 * @data_len: Length of the EAPOL packet in octets
	 * @encrypt: Whether the frame should be encrypted
	 * @own_addr: Source MAC address
	 * @flags: WPA_STA_* flags for the destination station
	 * @link_id: Link ID to use for TX, or -1 if not set
	 *
	 * Returns: 0 on success, -1 on failure
	 */
	int (*hapd_send_eapol)(void *priv, const u8 *addr, const u8 *data,
			       size_t data_len, int encrypt,
			       const u8 *own_addr, u32 flags, int link_id);

	/**
	 * sta_deauth - Deauthenticate a station (AP only)
	 * @priv: Private driver interface data
	 * @own_addr: Source address and BSSID for the Deauthentication frame
	 * @addr: MAC address of the station to deauthenticate
	 * @reason: Reason code for the Deauthentication frame
	 * @link_id: Link ID to use for Deauthentication frame, or -1 if not set
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function requests a specific station to be deauthenticated and
	 * a Deauthentication frame to be sent to it.
	 */
	int (*sta_deauth)(void *priv, const u8 *own_addr, const u8 *addr,
			  u16 reason, int link_id);

	/**
	 * sta_disassoc - Disassociate a station (AP only)
	 * @priv: Private driver interface data
	 * @own_addr: Source address and BSSID for the Disassociation frame
	 * @addr: MAC address of the station to disassociate
	 * @reason: Reason code for the Disassociation frame
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function requests a specific station to be disassociated and
	 * a Disassociation frame to be sent to it.
	 */
	int (*sta_disassoc)(void *priv, const u8 *own_addr, const u8 *addr,
			    u16 reason);

	/**
	 * sta_remove - Remove a station entry (AP only)
	 * @priv: Private driver interface data
	 * @addr: MAC address of the station to be removed
	 * Returns: 0 on success, -1 on failure
	 */
	int (*sta_remove)(void *priv, const u8 *addr);

	/**
	 * hapd_get_ssid - Get the current SSID (AP only)
	 * @priv: Private driver interface data
	 * @buf: Buffer for returning the SSID
	 * @len: Maximum length of the buffer
	 * Returns: Length of the SSID on success, -1 on failure
	 *
	 * This function need not be implemented if the driver uses Beacon
	 * template from set_ap() and does not reply to Probe Request frames.
	 */
	int (*hapd_get_ssid)(void *priv, u8 *buf, int len);

	/**
	 * hapd_set_ssid - Set SSID (AP only)
	 * @priv: Private driver interface data
	 * @buf: SSID
	 * @len: Length of the SSID in octets
	 * Returns: 0 on success, -1 on failure
	 *
	 * DEPRECATED - use set_ap() instead
	 */
	int (*hapd_set_ssid)(void *priv, const u8 *buf, int len);

	/**
	 * hapd_set_countermeasures - Enable/disable TKIP countermeasures (AP)
	 * @priv: Private driver interface data
	 * @enabled: 1 = countermeasures enabled, 0 = disabled
	 * Returns: 0 on success, -1 on failure
	 *
	 * This need not be implemented if the driver does not take care of
	 * association processing.
	 */
	int (*hapd_set_countermeasures)(void *priv, int enabled);

	/**
	 * sta_add - Add a station entry
	 * @priv: Private driver interface data
	 * @params: Station parameters
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function is used to add or set (params->set 1) a station
	 * entry in the driver. Adding STA entries is used only if the driver
	 * does not take care of association processing.
	 *
	 * With drivers that don't support full AP client state, this function
	 * is used to add a station entry to the driver once the station has
	 * completed association.
	 *
	 * With TDLS, this function is used to add or set (params->set 1)
	 * TDLS peer entries (even with drivers that do not support full AP
	 * client state).
	 */
	int (*sta_add)(void *priv, struct hostapd_sta_add_params *params);

	/**
	 * get_inact_sec - Get station inactivity duration (AP only)
	 * @priv: Private driver interface data
	 * @addr: Station address
	 * Returns: Number of seconds station has been inactive, -1 on failure
	 */
	int (*get_inact_sec)(void *priv, const u8 *addr);

	/**
	 * sta_clear_stats - Clear station statistics (AP only)
	 * @priv: Private driver interface data
	 * @addr: Station address
	 * Returns: 0 on success, -1 on failure
	 */
	int (*sta_clear_stats)(void *priv, const u8 *addr);

	/**
	 * set_freq - Set channel/frequency (AP only)
	 * @priv: Private driver interface data
	 * @freq: Channel parameters
	 * Returns: 0 on success, -1 on failure
	 */
	int (*set_freq)(void *priv, struct hostapd_freq_params *freq);

	/**
	 * set_rts - Set RTS threshold
	 * @priv: Private driver interface data
	 * @rts: RTS threshold in octets
	 * Returns: 0 on success, -1 on failure
	 */
	int (*set_rts)(void *priv, int rts);

	/**
	 * set_frag - Set fragmentation threshold
	 * @priv: Private driver interface data
	 * @frag: Fragmentation threshold in octets
	 * Returns: 0 on success, -1 on failure
	 */
	int (*set_frag)(void *priv, int frag);

	/**
	 * sta_set_flags - Set station flags (AP only)
	 * @priv: Private driver interface data
	 * @addr: Station address
	 * @total_flags: Bitmap of all WPA_STA_* flags currently set
	 * @flags_or: Bitmap of WPA_STA_* flags to add
	 * @flags_and: Bitmap of WPA_STA_* flags to us as a mask
	 * Returns: 0 on success, -1 on failure
	 */
	int (*sta_set_flags)(void *priv, const u8 *addr,
			     unsigned int total_flags, unsigned int flags_or,
			     unsigned int flags_and);

	/**
	 * sta_set_airtime_weight - Set station airtime weight (AP only)
	 * @priv: Private driver interface data
	 * @addr: Station address
	 * @weight: New weight for station airtime assignment
	 * Returns: 0 on success, -1 on failure
	 */
	int (*sta_set_airtime_weight)(void *priv, const u8 *addr,
				      unsigned int weight);

	/**
	 * set_tx_queue_params - Set TX queue parameters
	 * @priv: Private driver interface data
	 * @queue: Queue number (0 = VO, 1 = VI, 2 = BE, 3 = BK)
	 * @aifs: AIFS
	 * @cw_min: cwMin
	 * @cw_max: cwMax
	 * @burst_time: Maximum length for bursting in 0.1 msec units
	 * @link_id: Link ID to use, or -1 for non MLD.
	 */
	int (*set_tx_queue_params)(void *priv, int queue, int aifs, int cw_min,
				   int cw_max, int burst_time, int link_id);

	/**
	 * if_add - Add a virtual interface
	 * @priv: Private driver interface data
	 * @type: Interface type
	 * @ifname: Interface name for the new virtual interface
	 * @addr: Local address to use for the interface or %NULL to use the
	 *	parent interface address
	 * @bss_ctx: BSS context for %WPA_IF_AP_BSS interfaces
	 * @drv_priv: Pointer for overwriting the driver context or %NULL if
	 *	not allowed (applies only to %WPA_IF_AP_BSS type)
	 * @force_ifname: Buffer for returning an interface name that the
	 *	driver ended up using if it differs from the requested ifname
	 * @if_addr: Buffer for returning the allocated interface address
	 *	(this may differ from the requested addr if the driver cannot
	 *	change interface address)
	 * @bridge: Bridge interface to use or %NULL if no bridge configured
	 * @use_existing: Whether to allow existing interface to be used
	 * @setup_ap: Whether to setup AP for %WPA_IF_AP_BSS interfaces
	 * Returns: 0 on success, -1 on failure
	 */
	int (*if_add)(void *priv, enum wpa_driver_if_type type,
		      const char *ifname, const u8 *addr, void *bss_ctx,
		      void **drv_priv, char *force_ifname, u8 *if_addr,
		      const char *bridge, int use_existing, int setup_ap);

	/**
	 * if_remove - Remove a virtual interface
	 * @priv: Private driver interface data
	 * @type: Interface type
	 * @ifname: Interface name of the virtual interface to be removed
	 * Returns: 0 on success, -1 on failure
	 */
	int (*if_remove)(void *priv, enum wpa_driver_if_type type,
			 const char *ifname);

	/**
	 * set_sta_vlan - Bind a station into a specific interface (AP only)
	 * @priv: Private driver interface data
	 * @ifname: Interface (main or virtual BSS or VLAN)
	 * @addr: MAC address of the associated station
	 * @vlan_id: VLAN ID
	 * @link_id: The link ID or -1 for non-MLO
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function is used to bind a station to a specific virtual
	 * interface. It is only used if when virtual interfaces are supported,
	 * e.g., to assign stations to different VLAN interfaces based on
	 * information from a RADIUS server. This allows separate broadcast
	 * domains to be used with a single BSS.
	 */
	int (*set_sta_vlan)(void *priv, const u8 *addr, const char *ifname,
			    int vlan_id, int link_id);

	/**
	 * commit - Optional commit changes handler (AP only)
	 * @priv: driver private data
	 * Returns: 0 on success, -1 on failure
	 *
	 * This optional handler function can be registered if the driver
	 * interface implementation needs to commit changes (e.g., by setting
	 * network interface up) at the end of initial configuration. If set,
	 * this handler will be called after initial setup has been completed.
	 */
	int (*commit)(void *priv);

	/**
	 * set_radius_acl_auth - Notification of RADIUS ACL change
	 * @priv: Private driver interface data
	 * @mac: MAC address of the station
	 * @accepted: Whether the station was accepted
	 * @session_timeout: Session timeout for the station
	 * Returns: 0 on success, -1 on failure
	 */
	int (*set_radius_acl_auth)(void *priv, const u8 *mac, int accepted,
				   u32 session_timeout);

	/**
	 * set_radius_acl_expire - Notification of RADIUS ACL expiration
	 * @priv: Private driver interface data
	 * @mac: MAC address of the station
	 * Returns: 0 on success, -1 on failure
	 */
	int (*set_radius_acl_expire)(void *priv, const u8 *mac);

	/**
	 * set_ap_wps_ie - Add WPS IE(s) into Beacon/Probe Response frames (AP)
	 * @priv: Private driver interface data
	 * @beacon: WPS IE(s) for Beacon frames or %NULL to remove extra IE(s)
	 * @proberesp: WPS IE(s) for Probe Response frames or %NULL to remove
	 *	extra IE(s)
	 * @assocresp: WPS IE(s) for (Re)Association Response frames or %NULL
	 *	to remove extra IE(s)
	 * Returns: 0 on success, -1 on failure
	 *
	 * This is an optional function to add WPS IE in the kernel driver for
	 * Beacon and Probe Response frames. This can be left undefined (set
	 * to %NULL) if the driver uses the Beacon template from set_ap()
	 * and does not process Probe Request frames. If the driver takes care
	 * of (Re)Association frame processing, the assocresp buffer includes
	 * WPS IE(s) that need to be added to (Re)Association Response frames
	 * whenever a (Re)Association Request frame indicated use of WPS.
	 *
	 * This will also be used to add P2P IE(s) into Beacon/Probe Response
	 * frames when operating as a GO. The driver is responsible for adding
	 * timing related attributes (e.g., NoA) in addition to the IEs
	 * included here by appending them after these buffers. This call is
	 * also used to provide Probe Response IEs for P2P Listen state
	 * operations for drivers that generate the Probe Response frames
	 * internally.
	 *
	 * DEPRECATED - use set_ap() instead
	 */
	int (*set_ap_wps_ie)(void *priv, const struct wpabuf *beacon,
			     const struct wpabuf *proberesp,
			     const struct wpabuf *assocresp);

	/**
	 * set_supp_port - Set IEEE 802.1X Supplicant Port status
	 * @priv: Private driver interface data
	 * @authorized: Whether the port is authorized
	 * Returns: 0 on success, -1 on failure
	 */
	int (*set_supp_port)(void *priv, int authorized);

	/**
	 * set_wds_sta - Bind a station into a 4-address WDS (AP only)
	 * @priv: Private driver interface data
	 * @addr: MAC address of the associated station
	 * @aid: Association ID
	 * @val: 1 = bind to 4-address WDS; 0 = unbind
	 * @bridge_ifname: Bridge interface to use for the WDS station or %NULL
	 *	to indicate that bridge is not to be used
	 * @ifname_wds: Buffer to return the interface name for the new WDS
	 *	station or %NULL to indicate name is not returned.
	 * Returns: 0 on success, -1 on failure
	 */
	int (*set_wds_sta)(void *priv, const u8 *addr, int aid, int val,
			   const char *bridge_ifname, char *ifname_wds);

	/**
	 * send_action - Transmit an Action frame
	 * @priv: Private driver interface data
	 * @freq: Frequency (in MHz) of the channel
	 * @wait: Time to wait off-channel for a response (in ms), or zero
	 * @dst: Destination MAC address (Address 1)
	 * @src: Source MAC address (Address 2)
	 * @bssid: BSSID (Address 3)
	 * @data: Frame body
	 * @data_len: data length in octets
	 @ @no_cck: Whether CCK rates must not be used to transmit this frame
	 * Returns: 0 on success, -1 on failure
	 *
	 * This command can be used to request the driver to transmit an action
	 * frame to the specified destination.
	 *
	 * If the %WPA_DRIVER_FLAGS_OFFCHANNEL_TX flag is set, the frame will
	 * be transmitted on the given channel and the device will wait for a
	 * response on that channel for the given wait time.
	 *
	 * If the flag is not set, the wait time will be ignored. In this case,
	 * if a remain-on-channel duration is in progress, the frame must be
	 * transmitted on that channel; alternatively the frame may be sent on
	 * the current operational channel (if in associated state in station
	 * mode or while operating as an AP.)
	 *
	 * If @src differs from the device MAC address, use of a random
	 * transmitter address is requested for this message exchange.
	 */
	int (*send_action)(void *priv, unsigned int freq, unsigned int wait,
			   const u8 *dst, const u8 *src, const u8 *bssid,
			   const u8 *data, size_t data_len, int no_cck);

	/**
	 * send_action_cancel_wait - Cancel action frame TX wait
	 * @priv: Private driver interface data
	 *
	 * This command cancels the wait time associated with sending an action
	 * frame. It is only available when %WPA_DRIVER_FLAGS_OFFCHANNEL_TX is
	 * set in the driver flags.
	 */
	void (*send_action_cancel_wait)(void *priv);

	/**
	 * remain_on_channel - Remain awake on a channel
	 * @priv: Private driver interface data
	 * @freq: Frequency (in MHz) of the channel
	 * @duration: Duration in milliseconds
	 * Returns: 0 on success, -1 on failure
	 *
	 * This command is used to request the driver to remain awake on the
	 * specified channel for the specified duration and report received
	 * Action frames with EVENT_RX_MGMT events. Optionally, received
	 * Probe Request frames may also be requested to be reported by calling
	 * probe_req_report(). These will be reported with EVENT_RX_PROBE_REQ.
	 *
	 * The driver may not be at the requested channel when this function
	 * returns, i.e., the return code is only indicating whether the
	 * request was accepted. The caller will need to wait until the
	 * EVENT_REMAIN_ON_CHANNEL event indicates that the driver has
	 * completed the channel change. This may take some time due to other
	 * need for the radio and the caller should be prepared to timing out
	 * its wait since there are no guarantees on when this request can be
	 * executed.
	 */
	int (*remain_on_channel)(void *priv, unsigned int freq,
				 unsigned int duration);

	/**
	 * cancel_remain_on_channel - Cancel remain-on-channel operation
	 * @priv: Private driver interface data
	 *
	 * This command can be used to cancel a remain-on-channel operation
	 * before its originally requested duration has passed. This could be
	 * used, e.g., when remain_on_channel() is used to request extra time
	 * to receive a response to an Action frame and the response is
	 * received when there is still unneeded time remaining on the
	 * remain-on-channel operation.
	 */
	int (*cancel_remain_on_channel)(void *priv);

	/**
	 * probe_req_report - Request Probe Request frames to be indicated
	 * @priv: Private driver interface data
	 * @report: Whether to report received Probe Request frames
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 *
	 * This command can be used to request the driver to indicate when
	 * Probe Request frames are received with EVENT_RX_PROBE_REQ events.
	 * Since this operation may require extra resources, e.g., due to less
	 * optimal hardware/firmware RX filtering, many drivers may disable
	 * Probe Request reporting at least in station mode. This command is
	 * used to notify the driver when the Probe Request frames need to be
	 * reported, e.g., during remain-on-channel operations.
	 */
	int (*probe_req_report)(void *priv, int report);

	/**
	 * deinit_ap - Deinitialize AP mode
	 * @priv: Private driver interface data
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 *
	 * This optional function can be used to disable AP mode related
	 * configuration. If the interface was not dynamically added,
	 * change the driver mode to station mode to allow normal station
	 * operations like scanning to be completed.
	 */
	int (*deinit_ap)(void *priv);

	/**
	 * deinit_p2p_cli - Deinitialize P2P client mode
	 * @priv: Private driver interface data
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 *
	 * This optional function can be used to disable P2P client mode. If the
	 * interface was not dynamically added, change the interface type back
	 * to station mode.
	 */
	int (*deinit_p2p_cli)(void *priv);

	/**
	 * suspend - Notification on system suspend/hibernate event
	 * @priv: Private driver interface data
	 */
	void (*suspend)(void *priv);

	/**
	 * resume - Notification on system resume/thaw event
	 * @priv: Private driver interface data
	 */
	void (*resume)(void *priv);

	/**
	 * signal_monitor - Set signal monitoring parameters
	 * @priv: Private driver interface data
	 * @threshold: Threshold value for signal change events; 0 = disabled
	 * @hysteresis: Minimum change in signal strength before indicating a
	 *	new event
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 *
	 * This function can be used to configure monitoring of signal strength
	 * with the current AP. Whenever signal strength drops below the
	 * %threshold value or increases above it, EVENT_SIGNAL_CHANGE event
	 * should be generated assuming the signal strength has changed at
	 * least %hysteresis from the previously indicated signal change event.
	 */
	int (*signal_monitor)(void *priv, int threshold, int hysteresis);

	/**
	 * get_noa - Get current Notice of Absence attribute payload
	 * @priv: Private driver interface data
	 * @buf: Buffer for returning NoA
	 * @buf_len: Buffer length in octets
	 * Returns: Number of octets used in buf, 0 to indicate no NoA is being
	 * advertized, or -1 on failure
	 *
	 * This function is used to fetch the current Notice of Absence
	 * attribute value from GO.
	 */
	int (*get_noa)(void *priv, u8 *buf, size_t buf_len);

	/**
	 * set_noa - Set Notice of Absence parameters for GO (testing)
	 * @priv: Private driver interface data
	 * @count: Count
	 * @start: Start time in ms from next TBTT
	 * @duration: Duration in ms
	 * Returns: 0 on success or -1 on failure
	 *
	 * This function is used to set Notice of Absence parameters for GO. It
	 * is used only for testing. To disable NoA, all parameters are set to
	 * 0.
	 */
	int (*set_noa)(void *priv, u8 count, int start, int duration);

	/**
	 * set_p2p_powersave - Set P2P power save options
	 * @priv: Private driver interface data
	 * @legacy_ps: 0 = disable, 1 = enable, 2 = maximum PS, -1 = no change
	 * @opp_ps: 0 = disable, 1 = enable, -1 = no change
	 * @ctwindow: 0.. = change (msec), -1 = no change
	 * Returns: 0 on success or -1 on failure
	 */
	int (*set_p2p_powersave)(void *priv, int legacy_ps, int opp_ps,
				 int ctwindow);

	/**
	 * ampdu - Enable/disable aggregation
	 * @priv: Private driver interface data
	 * @ampdu: 1/0 = enable/disable A-MPDU aggregation
	 * Returns: 0 on success or -1 on failure
	 */
	int (*ampdu)(void *priv, int ampdu);

	/**
	 * get_radio_name - Get physical radio name for the device
	 * @priv: Private driver interface data
	 * Returns: Radio name or %NULL if not known
	 *
	 * The returned data must not be modified by the caller. It is assumed
	 * that any interface that has the same radio name as another is
	 * sharing the same physical radio. This information can be used to
	 * share scan results etc. information between the virtual interfaces
	 * to speed up various operations.
	 */
	const char * (*get_radio_name)(void *priv);

	/**
	 * send_tdls_mgmt - for sending TDLS management packets
	 * @priv: private driver interface data
	 * @dst: Destination (peer) MAC address
	 * @action_code: TDLS action code for the mssage
	 * @dialog_token: Dialog Token to use in the message (if needed)
	 * @status_code: Status Code or Reason Code to use (if needed)
	 * @peer_capab: TDLS peer capability (TDLS_PEER_* bitfield)
	 * @initiator: Is the current end the TDLS link initiator
	 * @buf: TDLS IEs to add to the message
	 * @len: Length of buf in octets
	 * @link_id: If >= 0 indicates the link of the AP MLD to specify the
	 * operating channel on which to send a TDLS Discovery Response frame.
	 * Returns: 0 on success, negative (<0) on failure
	 *
	 * This optional function can be used to send packet to driver which is
	 * responsible for receiving and sending all TDLS packets.
	 */
	int (*send_tdls_mgmt)(void *priv, const u8 *dst, u8 action_code,
			      u8 dialog_token, u16 status_code, u32 peer_capab,
			      int initiator, const u8 *buf, size_t len,
			      int link_id);

	/**
	 * tdls_oper - Ask the driver to perform high-level TDLS operations
	 * @priv: Private driver interface data
	 * @oper: TDLS high-level operation. See %enum tdls_oper
	 * @peer: Destination (peer) MAC address
	 * Returns: 0 on success, negative (<0) on failure
	 *
	 * This optional function can be used to send high-level TDLS commands
	 * to the driver.
	 */
	int (*tdls_oper)(void *priv, enum tdls_oper oper, const u8 *peer);

	/**
	 * wnm_oper - Notify driver of the WNM frame reception
	 * @priv: Private driver interface data
	 * @oper: WNM operation. See %enum wnm_oper
	 * @peer: Destination (peer) MAC address
	 * @buf: Buffer for the driver to fill in (for getting IE)
	 * @buf_len: Return the len of buf
	 * Returns: 0 on success, negative (<0) on failure
	 */
	int (*wnm_oper)(void *priv, enum wnm_oper oper, const u8 *peer,
			u8 *buf, u16 *buf_len);

	/**
	 * set_qos_map - Set QoS Map
	 * @priv: Private driver interface data
	 * @qos_map_set: QoS Map
	 * @qos_map_set_len: Length of QoS Map
	 */
	int (*set_qos_map)(void *priv, const u8 *qos_map_set,
			   u8 qos_map_set_len);

	/**
	 * br_add_ip_neigh - Add a neigh to the bridge ip neigh table
	 * @priv: Private driver interface data
	 * @version: IP version of the IP address, 4 or 6
	 * @ipaddr: IP address for the neigh entry
	 * @prefixlen: IP address prefix length
	 * @addr: Corresponding MAC address
	 * Returns: 0 on success, negative (<0) on failure
	 */
	int (*br_add_ip_neigh)(void *priv, u8 version, const u8 *ipaddr,
			       int prefixlen, const u8 *addr);

	/**
	 * br_delete_ip_neigh - Remove a neigh from the bridge ip neigh table
	 * @priv: Private driver interface data
	 * @version: IP version of the IP address, 4 or 6
	 * @ipaddr: IP address for the neigh entry
	 * Returns: 0 on success, negative (<0) on failure
	 */
	int (*br_delete_ip_neigh)(void *priv, u8 version, const u8 *ipaddr);

	/**
	 * br_port_set_attr - Set a bridge port attribute
	 * @attr: Bridge port attribute to set
	 * @val: Value to be set
	 * Returns: 0 on success, negative (<0) on failure
	 */
	int (*br_port_set_attr)(void *priv, enum drv_br_port_attr attr,
				unsigned int val);

	/**
	 * br_port_set_attr - Set a bridge network parameter
	 * @param: Bridge parameter to set
	 * @val: Value to be set
	 * Returns: 0 on success, negative (<0) on failure
	 */
	int (*br_set_net_param)(void *priv, enum drv_br_net_param param,
				unsigned int val);

	/**
	 * get_wowlan - Get wake-on-wireless status
	 * @priv: Private driver interface data
	 */
	int (*get_wowlan)(void *priv);

	/**
	 * set_wowlan - Set wake-on-wireless triggers
	 * @priv: Private driver interface data
	 * @triggers: wowlan triggers
	 */
	int (*set_wowlan)(void *priv, const struct wowlan_triggers *triggers);

	/**
	 * signal_poll - Get current connection information
	 * @priv: Private driver interface data
	 * @signal_info: Connection info structure
	 */
	int (*signal_poll)(void *priv, struct wpa_signal_info *signal_info);

	/**
	 * mlo_signal_poll - Get current MLO connection information
	 * @priv: Private driver interface data
	 * @mlo_signal_info: MLO connection info structure
	 */
	int (*mlo_signal_poll)(void *priv,
			       struct wpa_mlo_signal_info *mlo_signal_info);

	/**
	 * channel_info - Get parameters of the current operating channel
	 * @priv: Private driver interface data
	 * @channel_info: Channel info structure
	 * Returns: 0 on success, negative (<0) on failure
	 */
	int (*channel_info)(void *priv, struct wpa_channel_info *channel_info);

	/**
	 * set_authmode - Set authentication algorithm(s) for static WEP
	 * @priv: Private driver interface data
	 * @authmode: 1=Open System, 2=Shared Key, 3=both
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function can be used to set authentication algorithms for AP
	 * mode when static WEP is used. If the driver uses user space MLME/SME
	 * implementation, there is no need to implement this function.
	 *
	 * DEPRECATED - use set_ap() instead
	 */
	int (*set_authmode)(void *priv, int authmode);

#ifdef ANDROID
	/**
	 * driver_cmd - Execute driver-specific command
	 * @priv: Private driver interface data
	 * @cmd: Command to execute
	 * @buf: Return buffer
	 * @buf_len: Buffer length
	 * Returns: 0 on success, -1 on failure
	 */
	int (*driver_cmd)(void *priv, char *cmd, char *buf, size_t buf_len);
#endif /* ANDROID */

	/**
	 * vendor_cmd - Execute vendor specific command
	 * @priv: Private driver interface data
	 * @vendor_id: Vendor id
	 * @subcmd: Vendor command id
	 * @nested_attr_flag: Specifies if vendor subcommand uses nested
	 *	attributes or not
	 * @data: Vendor command parameters (%NULL if no parameters)
	 * @data_len: Data length
	 * @buf: Return buffer (%NULL to ignore reply)
	 * Returns: 0 on success, negative (<0) on failure
	 *
	 * This function handles vendor specific commands that are passed to
	 * the driver/device. The command is identified by vendor id and
	 * command id. The nested_attr_flag specifies whether the subcommand
	 * uses nested attributes or not. Parameters can be passed
	 * as argument to the command in the data buffer. Reply (if any) will be
	 * filled in the supplied return buffer.
	 *
	 * The exact driver behavior is driver interface and vendor specific. As
	 * an example, this will be converted to a vendor specific cfg80211
	 * command in case of the nl80211 driver interface.
	 */
	int (*vendor_cmd)(void *priv, unsigned int vendor_id,
			  unsigned int subcmd, const u8 *data, size_t data_len,
			  enum nested_attr nested_attr_flag,
			  struct wpabuf *buf);

	/**
	 * set_rekey_info - Set rekey information
	 * @priv: Private driver interface data
	 * @kek: Current KEK
	 * @kek_len: KEK length in octets
	 * @kck: Current KCK
	 * @kck_len: KCK length in octets
	 * @replay_ctr: Current EAPOL-Key Replay Counter
	 *
	 * This optional function can be used to provide information for the
	 * driver/firmware to process EAPOL-Key frames in Group Key Handshake
	 * while the host (including wpa_supplicant) is sleeping.
	 */
	void (*set_rekey_info)(void *priv, const u8 *kek, size_t kek_len,
			       const u8 *kck, size_t kck_len,
			       const u8 *replay_ctr);

	/**
	 * sta_assoc - Station association indication
	 * @priv: Private driver interface data
	 * @own_addr: Source address and BSSID for association frame
	 * @addr: MAC address of the station to associate
	 * @reassoc: flag to indicate re-association
	 * @status: association response status code
	 * @ie: assoc response ie buffer
	 * @len: ie buffer length
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function indicates the driver to send (Re)Association
	 * Response frame to the station.
	 */
	 int (*sta_assoc)(void *priv, const u8 *own_addr, const u8 *addr,
			  int reassoc, u16 status, const u8 *ie, size_t len);

	/**
	 * sta_auth - Station authentication indication
	 * @priv: private driver interface data
	 * @params: Station authentication parameters
	 *
	 * Returns: 0 on success, -1 on failure
	 */
	 int (*sta_auth)(void *priv,
			 struct wpa_driver_sta_auth_params *params);

	/**
	 * add_tspec - Add traffic stream
	 * @priv: Private driver interface data
	 * @addr: MAC address of the station to associate
	 * @tspec_ie: tspec ie buffer
	 * @tspec_ielen: tspec ie length
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function adds the traffic steam for the station
	 * and fills the medium_time in tspec_ie.
	 */
	 int (*add_tspec)(void *priv, const u8 *addr, u8 *tspec_ie,
			  size_t tspec_ielen);

	/**
	 * add_sta_node - Add a station node in the driver
	 * @priv: Private driver interface data
	 * @addr: MAC address of the station to add
	 * @auth_alg: authentication algorithm used by the station
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function adds the station node in the driver, when
	 * the station gets added by FT-over-DS.
	 */
	int (*add_sta_node)(void *priv, const u8 *addr, u16 auth_alg);

	/**
	 * sched_scan - Request the driver to initiate scheduled scan
	 * @priv: Private driver interface data
	 * @params: Scan parameters
	 * Returns: 0 on success, -1 on failure
	 *
	 * This operation should be used for scheduled scan offload to
	 * the hardware. Every time scan results are available, the
	 * driver should report scan results event for wpa_supplicant
	 * which will eventually request the results with
	 * wpa_driver_get_scan_results2(). This operation is optional
	 * and if not provided or if it returns -1, we fall back to
	 * normal host-scheduled scans.
	 */
	int (*sched_scan)(void *priv, struct wpa_driver_scan_params *params);

	/**
	 * stop_sched_scan - Request the driver to stop a scheduled scan
	 * @priv: Private driver interface data
	 * Returns: 0 on success, -1 on failure
	 *
	 * This should cause the scheduled scan to be stopped and
	 * results should stop being sent. Must be supported if
	 * sched_scan is supported.
	 */
	int (*stop_sched_scan)(void *priv);

	/**
	 * poll_client - Probe (null data or such) the given station
	 * @priv: Private driver interface data
	 * @own_addr: MAC address of sending interface
	 * @addr: MAC address of the station to probe
	 * @qos: Indicates whether station is QoS station
	 *
	 * This function is used to verify whether an associated station is
	 * still present. This function does not need to be implemented if the
	 * driver provides such inactivity polling mechanism.
	 */
	void (*poll_client)(void *priv, const u8 *own_addr,
			    const u8 *addr, int qos);

	/**
	 * radio_disable - Disable/enable radio
	 * @priv: Private driver interface data
	 * @disabled: 1=disable 0=enable radio
	 * Returns: 0 on success, -1 on failure
	 *
	 * This optional command is for testing purposes. It can be used to
	 * disable the radio on a testbed device to simulate out-of-radio-range
	 * conditions.
	 */
	int (*radio_disable)(void *priv, int disabled);

	/**
	 * switch_channel - Announce channel switch and migrate the GO to the
	 * given frequency
	 * @priv: Private driver interface data
	 * @settings: Settings for CSA period and new channel
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function is used to move the GO to the legacy STA channel to
	 * avoid frequency conflict in single channel concurrency.
	 */
	int (*switch_channel)(void *priv, struct csa_settings *settings);

	/**
	 * switch_color - Announce color switch and migrate the BSS to the
	 * given color
	 * @priv: Private driver interface data
	 * @settings: Settings for CCA period and new color
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function is used to move the BSS to its new color.
	 */
	int (*switch_color)(void *priv, struct cca_settings *settings);

	/**
	 * add_tx_ts - Add traffic stream
	 * @priv: Private driver interface data
	 * @tsid: Traffic stream ID
	 * @addr: Receiver address
	 * @user_prio: User priority of the traffic stream
	 * @admitted_time: Admitted time for this TS in units of
	 *	32 microsecond periods (per second).
	 * Returns: 0 on success, -1 on failure
	 */
	int (*add_tx_ts)(void *priv, u8 tsid, const u8 *addr, u8 user_prio,
			 u16 admitted_time);

	/**
	 * del_tx_ts - Delete traffic stream
	 * @priv: Private driver interface data
	 * @tsid: Traffic stream ID
	 * @addr: Receiver address
	 * Returns: 0 on success, -1 on failure
	 */
	int (*del_tx_ts)(void *priv, u8 tsid, const u8 *addr);

	/**
	 * Enable channel-switching with TDLS peer
	 * @priv: Private driver interface data
	 * @addr: MAC address of the TDLS peer
	 * @oper_class: Operating class of the switch channel
	 * @params: Channel specification
	 * Returns: 0 on success, -1 on failure
	 *
	 * The function indicates to driver that it can start switching to a
	 * different channel with a specified TDLS peer. The switching is
	 * assumed on until canceled with tdls_disable_channel_switch().
	 */
	int (*tdls_enable_channel_switch)(
		void *priv, const u8 *addr, u8 oper_class,
		const struct hostapd_freq_params *params);

	/**
	 * Disable channel switching with TDLS peer
	 * @priv: Private driver interface data
	 * @addr: MAC address of the TDLS peer
	 * Returns: 0 on success, -1 on failure
	 *
	 * This function indicates to the driver that it should stop switching
	 * with a given TDLS peer.
	 */
	int (*tdls_disable_channel_switch)(void *priv, const u8 *addr);

	/**
	 * start_dfs_cac - Listen for radar interference on the channel
	 * @priv: Private driver interface data
	 * @freq: Channel parameters
	 * Returns: 0 on success, -1 on failure
	 */
	int (*start_dfs_cac)(void *priv, struct hostapd_freq_params *freq);

	/**
	 * stop_ap - Removes beacon from AP
	 * @priv: Private driver interface data
	 * @link_id: Link ID of the specified link; -1 for non-MLD
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 *
	 * This optional function can be used to disable AP mode related
	 * configuration. Unlike deinit_ap, it does not change to station
	 * mode.
	 */
	int (*stop_ap)(void *priv, int link_id);

	/**
	 * get_survey - Retrieve survey data
	 * @priv: Private driver interface data
	 * @freq: If set, survey data for the specified frequency is only
	 *	being requested. If not set, all survey data is requested.
	 * Returns: 0 on success, -1 on failure
	 *
	 * Use this to retrieve:
	 *
	 * - the observed channel noise floor
	 * - the amount of time we have spent on the channel
	 * - the amount of time during which we have spent on the channel that
	 *   the radio has determined the medium is busy and we cannot
	 *   transmit
	 * - the amount of time we have spent receiving data
	 * - the amount of time we have spent transmitting data
	 *
	 * This data can be used for spectrum heuristics. One example is
	 * Automatic Channel Selection (ACS). The channel survey data is
	 * kept on a linked list on the channel data, one entry is added
	 * for each survey. The min_nf of the channel is updated for each
	 * survey.
	 */
	int (*get_survey)(void *priv, unsigned int freq);

	/**
	 * status - Get driver interface status information
	 * @priv: Private driver interface data
	 * @buf: Buffer for printing the status information
	 * @buflen: Maximum length of the buffer
	 * Returns: Length of written status information or -1 on failure
	 */
	int (*status)(void *priv, char *buf, size_t buflen);

	/**
	 * roaming - Set roaming policy for driver-based BSS selection
	 * @priv: Private driver interface data
	 * @allowed: Whether roaming within ESS is allowed
	 * @bssid: Forced BSSID if roaming is disabled or %NULL if not set
	 * Returns: Length of written status information or -1 on failure
	 *
	 * This optional callback can be used to update roaming policy from the
	 * associate() command (bssid being set there indicates that the driver
	 * should not roam before getting this roaming() call to allow roaming.
	 * If the driver does not indicate WPA_DRIVER_FLAGS_BSS_SELECTION
	 * capability, roaming policy is handled within wpa_supplicant and there
	 * is no need to implement or react to this callback.
	 */
	int (*roaming)(void *priv, int allowed, const u8 *bssid);

	/**
	 * disable_fils - Enable/disable FILS feature
	 * @priv: Private driver interface data
	 * @disable: 0-enable and 1-disable FILS feature
	 * Returns: 0 on success, -1 on failure
	 *
	 * This callback can be used to configure driver and below layers to
	 * enable/disable all FILS features.
	 */
	int (*disable_fils)(void *priv, int disable);

	/**
	 * set_mac_addr - Set MAC address
	 * @priv: Private driver interface data
	 * @addr: MAC address to use or %NULL for setting back to permanent
	 * Returns: 0 on success, -1 on failure
	 */
	int (*set_mac_addr)(void *priv, const u8 *addr);

#ifdef CONFIG_MACSEC
	int (*macsec_init)(void *priv, struct macsec_init_params *params);

	int (*macsec_deinit)(void *priv);

	/**
	 * macsec_get_capability - Inform MKA of this driver's capability
	 * @priv: Private driver interface data
	 * @cap: Driver's capability
	 * Returns: 0 on success, -1 on failure
	 */
	int (*macsec_get_capability)(void *priv, enum macsec_cap *cap);

	/**
	 * enable_protect_frames - Set protect frames status
	 * @priv: Private driver interface data
	 * @enabled: true = protect frames enabled
	 *           false = protect frames disabled
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*enable_protect_frames)(void *priv, bool enabled);

	/**
	 * enable_encrypt - Set encryption status
	 * @priv: Private driver interface data
	 * @enabled: true = encrypt outgoing traffic
	 *           false = integrity-only protection on outgoing traffic
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*enable_encrypt)(void *priv, bool enabled);

	/**
	 * set_replay_protect - Set replay protect status and window size
	 * @priv: Private driver interface data
	 * @enabled: true = replay protect enabled
	 *           false = replay protect disabled
	 * @window: replay window size, valid only when replay protect enabled
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*set_replay_protect)(void *priv, bool enabled, u32 window);

	/**
	 * set_offload - Set MACsec hardware offload
	 * @priv: Private driver interface data
	 * @offload: 0 = MACSEC_OFFLOAD_OFF
	 *           1 = MACSEC_OFFLOAD_PHY
	 *           2 = MACSEC_OFFLOAD_MAC
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*set_offload)(void *priv, u8 offload);

	/**
	 * set_current_cipher_suite - Set current cipher suite
	 * @priv: Private driver interface data
	 * @cs: EUI64 identifier
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*set_current_cipher_suite)(void *priv, u64 cs);

	/**
	 * enable_controlled_port - Set controlled port status
	 * @priv: Private driver interface data
	 * @enabled: true = controlled port enabled
	 *           false = controlled port disabled
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*enable_controlled_port)(void *priv, bool enabled);

	/**
	 * get_receive_lowest_pn - Get receive lowest pn
	 * @priv: Private driver interface data
	 * @sa: secure association
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*get_receive_lowest_pn)(void *priv, struct receive_sa *sa);

	/**
	 * get_transmit_next_pn - Get transmit next pn
	 * @priv: Private driver interface data
	 * @sa: secure association
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*get_transmit_next_pn)(void *priv, struct transmit_sa *sa);

	/**
	 * set_transmit_next_pn - Set transmit next pn
	 * @priv: Private driver interface data
	 * @sa: secure association
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*set_transmit_next_pn)(void *priv, struct transmit_sa *sa);

	/**
	 * set_receive_lowest_pn - Set receive lowest PN
	 * @priv: Private driver interface data
	 * @sa: secure association
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*set_receive_lowest_pn)(void *priv, struct receive_sa *sa);

	/**
	 * create_receive_sc - create secure channel for receiving
	 * @priv: Private driver interface data
	 * @sc: secure channel
	 * @conf_offset: confidentiality offset (0, 30, or 50)
	 * @validation: frame validation policy (0 = Disabled, 1 = Checked,
	 *	2 = Strict)
	 * Returns: 0 on success, -1 on failure (or if not supported)
	 */
	int (*create_receive_sc)(void *priv, struct receive_sc *sc,
				 unsigned int conf_offset,
				 int validation);

	/**
	 * delete_receive_sc - delete secure connection for receiving
	 * @priv: private driver interface data from init()
	 * @sc: secure channel
	 * Returns: 0 on success, -1 on failure
	 */
	int (*delete_receive_sc)(void *priv, struct receive_sc *sc);

	/**
	 * create_receive_sa - create secure association for receive
	 * @priv: private driver interface data from init()
	 * @sa: secure association
	 * Returns: 0 on success, -1 on failure
	 */
	int (*create_receive_sa)(void *priv, struct receive_sa *sa);

	/**
	 * delete_receive_sa - Delete secure association for receive
	 * @priv: Private driver interface data from init()
	 * @sa: Secure association
	 * Returns: 0 on success, -1 on failure
	 */
	int (*delete_receive_sa)(void *priv, struct receive_sa *sa);

	/**
	 * enable_receive_sa - enable the SA for receive
	 * @priv: private driver interface data from init()
	 * @sa: secure association
	 * Returns: 0 on success, -1 on failure
	 */
	int (*enable_receive_sa)(void *priv, struct receive_sa *sa);

	/**
	 * disable_receive_sa - disable SA for receive
	 * @priv: private driver interface data from init()
	 * @sa: secure association
	 * Returns: 0 on success, -1 on failure
	 */
	int (*disable_receive_sa)(void *priv, struct receive_sa *sa);

	/**
	 * create_transmit_sc - create secure connection for transmit
	 * @priv: private driver interface data from init()
	 * @sc: secure channel
	 * @conf_offset: confidentiality offset (0, 30, or 50)
	 * Returns: 0 on success, -1 on failure
	 */
	int (*create_transmit_sc)(void *priv, struct transmit_sc *sc,
				  unsigned int conf_offset);

	/**
	 * delete_transmit_sc - delete secure connection for transmit
	 * @priv: private driver interface data from init()
	 * @sc: secure channel
	 * Returns: 0 on success, -1 on failure
	 */
	int (*delete_transmit_sc)(void *priv, struct transmit_sc *sc);

	/**
	 * create_transmit_sa - create secure association for transmit
	 * @priv: private driver interface data from init()
	 * @sa: secure association
	 * Returns: 0 on success, -1 on failure
	 */
	int (*create_transmit_sa)(void *priv, struct transmit_sa *sa);

	/**
	 * delete_transmit_sa - Delete secure association for transmit
	 * @priv: Private driver interface data from init()
	 * @sa: Secure association
	 * Returns: 0 on success, -1 on failure
	 */
	int (*delete_transmit_sa)(void *priv, struct transmit_sa *sa);

	/**
	 * enable_transmit_sa - enable SA for transmit
	 * @priv: private driver interface data from init()
	 * @sa: secure association
	 * Returns: 0 on success, -1 on failure
	 */
	int (*enable_transmit_sa)(void *priv, struct transmit_sa *sa);

	/**
	 * disable_transmit_sa - disable SA for transmit
	 * @priv: private driver interface data from init()
	 * @sa: secure association
	 * Returns: 0 on success, -1 on failure
	 */
	int (*disable_transmit_sa)(void *priv, struct transmit_sa *sa);
#endif /* CONFIG_MACSEC */

	/**
	 * init_mesh - Driver specific initialization for mesh
	 * @priv: Private driver interface data
	 * Returns: 0 on success, -1 on failure
	 */
	int (*init_mesh)(void *priv);

	/**
	 * join_mesh - Join a mesh network
	 * @priv: Private driver interface data
	 * @params: Mesh configuration parameters
	 * Returns: 0 on success, -1 on failure
	 */
	int (*join_mesh)(void *priv,
			 struct wpa_driver_mesh_join_params *params);

	/**
	 * leave_mesh - Leave a mesh network
	 * @priv: Private driver interface data
	 * Returns 0 on success, -1 on failure
	 */
	int (*leave_mesh)(void *priv);

	/**
	 * probe_mesh_link - Inject a frame over direct mesh link to a given
	 *	peer skipping the next_hop lookup from mpath table.
	 * @priv: Private driver interface data
	 * @addr: Peer MAC address
	 * @eth: Ethernet frame to be sent
	 * @len: Ethernet frame lengtn in bytes
	 * Returns 0 on success, -1 on failure
	 */
	int (*probe_mesh_link)(void *priv, const u8 *addr, const u8 *eth,
			       size_t len);

	/**
	 * do_acs - Automatically select channel
	 * @priv: Private driver interface data
	 * @params: Parameters for ACS
	 * Returns 0 on success, -1 on failure
	 *
	 * This command can be used to offload ACS to the driver if the driver
	 * indicates support for such offloading (WPA_DRIVER_FLAGS_ACS_OFFLOAD).
	 */
	int (*do_acs)(void *priv, struct drv_acs_params *params);

	/**
	 * set_band - Notify driver of band(s) selection
	 * @priv: Private driver interface data
	 * @band_mask: The selected band(s) bit mask (from enum set_band)
	 * Returns 0 on success, -1 on failure
	 */
	int (*set_band)(void *priv, u32 band_mask);

	/**
	 * get_pref_freq_list - Get preferred frequency list for an interface
	 * @priv: Private driver interface data
	 * @if_type: Interface type
	 * @num: Number of channels
	 * @freq_list: Weighted preferred channel list
	 * Returns 0 on success, -1 on failure
	 *
	 * This command can be used to query the preferred frequency list from
	 * the driver specific to a particular interface type. The freq_list
	 * array needs to have room for *num entries. *num will be updated to
	 * indicate the number of entries fetched from the driver.
	 */
	int (*get_pref_freq_list)(void *priv, enum wpa_driver_if_type if_type,
				  unsigned int *num,
				  struct weighted_pcl *freq_list);

	/**
	 * set_prob_oper_freq - Indicate probable P2P operating channel
	 * @priv: Private driver interface data
	 * @freq: Channel frequency in MHz
	 * Returns 0 on success, -1 on failure
	 *
	 * This command can be used to inform the driver of the operating
	 * frequency that an ongoing P2P group formation is likely to come up
	 * on. Local device is assuming P2P Client role.
	 */
	int (*set_prob_oper_freq)(void *priv, unsigned int freq);

	/**
	 * abort_scan - Request the driver to abort an ongoing scan
	 * @priv: Private driver interface data
	 * @scan_cookie: Cookie identifying the scan request. This is used only
	 *	when the vendor interface QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN
	 *	was used to trigger scan. Otherwise, 0 is used.
	 * Returns 0 on success, -1 on failure
	 */
	int (*abort_scan)(void *priv, u64 scan_cookie);

	/**
	 * configure_data_frame_filters - Request to configure frame filters
	 * @priv: Private driver interface data
	 * @filter_flags: The type of frames to filter (bitfield of
	 * WPA_DATA_FRAME_FILTER_FLAG_*)
	 * Returns: 0 on success or -1 on failure
	 */
	int (*configure_data_frame_filters)(void *priv, u32 filter_flags);

	/**
	 * get_ext_capab - Get extended capabilities for the specified interface
	 * @priv: Private driver interface data
	 * @type: Interface type for which to get extended capabilities
	 * @ext_capab: Extended capabilities fetched
	 * @ext_capab_mask: Extended capabilities mask
	 * @ext_capab_len: Length of the extended capabilities
	 * Returns: 0 on success or -1 on failure
	 */
	int (*get_ext_capab)(void *priv, enum wpa_driver_if_type type,
			     const u8 **ext_capab, const u8 **ext_capab_mask,
			     unsigned int *ext_capab_len);

	/**
	 * get_mld_capab - Get MLD capabilities for the specified interface
	 * @priv: Private driver interface data
	 * @type: Interface type for which to get MLD capabilities
	 * @eml_capa: EML capabilities
	 * @mld_capa_and_ops: MLD Capabilities and Operations
	 * Returns: 0 on success or -1 on failure
	 */
	int (*get_mld_capab)(void *priv, enum wpa_driver_if_type type,
			     u16 *eml_capa, u16 *mld_capa_and_ops);

	/**
	 * p2p_lo_start - Start offloading P2P listen to device
	 * @priv: Private driver interface data
	 * @freq: Listening frequency (MHz) for P2P listen
	 * @period: Length of the listen operation in milliseconds
	 * @interval: Interval for running the listen operation in milliseconds
	 * @count: Number of times to run the listen operation
	 * @device_types: Device primary and secondary types
	 * @dev_types_len: Number of bytes for device_types
	 * @ies: P2P IE and WSC IE for Probe Response frames
	 * @ies_len: Length of ies in bytes
	 * Returns: 0 on success or -1 on failure
	 */
	int (*p2p_lo_start)(void *priv, unsigned int freq,
			    unsigned int period, unsigned int interval,
			    unsigned int count,
			    const u8 *device_types, size_t dev_types_len,
			    const u8 *ies, size_t ies_len);

	/**
	 * p2p_lo_stop - Stop P2P listen offload
	 * @priv: Private driver interface data
	 * Returns: 0 on success or -1 on failure
	 */
	int (*p2p_lo_stop)(void *priv);

	/**
	 * set_default_scan_ies - Set default scan IEs
	 * @priv: Private driver interface data
	 * @ies: Scan default IEs buffer
	 * @ies_len: Length of IEs in bytes
	 * Returns: 0 on success or -1 on failure
	 *
	 * The driver can use these by default when there are no scan IEs coming
	 * in the subsequent scan requests. Also in case of one or more of IEs
	 * given in set_default_scan_ies() are missing in the subsequent scan
	 * request, the driver should merge the missing scan IEs in the scan
	 * request from the IEs set by set_default_scan_ies() in the Probe
	 * Request frames sent.
	 */
	int (*set_default_scan_ies)(void *priv, const u8 *ies, size_t ies_len);

	/**
	 * set_tdls_mode - Set TDLS trigger mode to the host driver
	 * @priv: Private driver interface data
	 * @tdls_external_control: Represents if TDLS external trigger control
	 *  mode is enabled/disabled.
	 *
	 * This optional callback can be used to configure the TDLS external
	 * trigger control mode to the host driver.
	 */
	int (*set_tdls_mode)(void *priv, int tdls_external_control);

	/**
	 * get_bss_transition_status - Get candidate BSS's transition status
	 * @priv: Private driver interface data
	 * @params: Candidate BSS list
	 *
	 * Get the accept or reject reason code for a list of BSS transition
	 * candidates.
	 */
	struct wpa_bss_candidate_info *
	(*get_bss_transition_status)(void *priv,
				     struct wpa_bss_trans_info *params);
	/**
	 * ignore_assoc_disallow - Configure driver to ignore assoc_disallow
	 * @priv: Private driver interface data
	 * @ignore_disallow: 0 to not ignore, 1 to ignore
	 * Returns: 0 on success, -1 on failure
	 */
	int (*ignore_assoc_disallow)(void *priv, int ignore_disallow);

	/**
	 * set_bssid_tmp_disallow - Set disallowed BSSIDs to the driver
	 * @priv: Private driver interface data
	 * @num_bssid: Number of temporarily disallowed BSSIDs
	 * @bssids: List of temporarily disallowed BSSIDs
	 */
	int (*set_bssid_tmp_disallow)(void *priv, unsigned int num_bssid,
				      const u8 *bssid);

	/**
	 * update_connect_params - Update the connection parameters
	 * @priv: Private driver interface data
	 * @params: Association parameters
	 * @mask: Bit mask indicating which parameters in @params have to be
	 *	updated
	 * Returns: 0 on success, -1 on failure
	 *
	 * Update the connection parameters when in connected state so that the
	 * driver uses the updated parameters for subsequent roaming. This is
	 * used only with drivers that implement internal BSS selection and
	 * roaming.
	 */
	int (*update_connect_params)(
		void *priv, struct wpa_driver_associate_params *params,
		enum wpa_drv_update_connect_params_mask mask);

	/**
	 * send_external_auth_status - Indicate the status of external
	 * authentication processing to the host driver.
	 * @priv: Private driver interface data
	 * @params: Status of authentication processing.
	 * Returns: 0 on success, -1 on failure
	 */
	int (*send_external_auth_status)(void *priv,
					 struct external_auth *params);

	/**
	 * set_4addr_mode - Set 4-address mode
	 * @priv: Private driver interface data
	 * @bridge_ifname: Bridge interface name
	 * @val: 0 - disable 4addr mode, 1 - enable 4addr mode
	 * Returns: 0 on success, < 0 on failure
	 */
	int (*set_4addr_mode)(void *priv, const char *bridge_ifname, int val);

	/**
	 * update_dh_ie - Update DH IE
	 * @priv: Private driver interface data
	 * @peer_mac: Peer MAC address
	 * @reason_code: Reacon code
	 * @ie: DH IE
	 * @ie_len: DH IE length in bytes
	 * Returns: 0 on success, -1 on failure
	 *
	 * This callback is used to let the driver know the DH processing result
	 * and DH IE for a pending association.
	 */
	int (*update_dh_ie)(void *priv, const u8 *peer_mac, u16 reason_code,
			    const u8 *ie, size_t ie_len);

	/**
	 * dpp_listen - Notify driver about start/stop of DPP listen
	 * @priv: Private driver interface data
	 * @enable: Whether listen state is enabled (or disabled)
	 * Returns: 0 on success, -1 on failure
	 *
	 * This optional callback can be used to update RX frame filtering to
	 * explicitly allow reception of broadcast Public Action frames.
	 */
	int (*dpp_listen)(void *priv, bool enable);

	/**
	 * set_secure_ranging_ctx - Add or delete secure ranging parameters of
	 * the specified peer to the driver.
	 * @priv: Private driver interface data
	 * @params: Secure ranging parameters
	 * Returns: 0 on success, -1 on failure
	 *
	 */
	int (*set_secure_ranging_ctx)(void *priv,
				      struct secure_ranging_params *params);

	/**
	 * send_pasn_resp - Send PASN response for a set of peers to the
	 * driver.
	 * @priv: Private driver interface data
	 * @params: Parameters holding peers and respective status.
	 * Returns: 0 on success, -1 on failure
	 */
	int (*send_pasn_resp)(void *priv, struct pasn_auth *params);

	/**
	 * get_sta_mlo_info - Get the current multi-link association info
	 * @priv: Private driver interface data
	 * @mlo: Pointer to fill multi-link association info
	 * Returns: 0 on success, -1 on failure
	 *
	 * This callback is used to fetch multi-link of the current association.
	 */
	int (*get_sta_mlo_info)(void *priv,
				struct driver_sta_mlo_info *mlo_info);

	/**
	 * link_add - Add a link to the AP MLD interface
	 * @priv: Private driver interface data
	 * @link_id: The link ID
	 * @addr: The MAC address to use for the link
	 * @bss_ctx: BSS context for %WPA_IF_AP_BSS interfaces
	 * Returns: 0 on success, negative value on failure
	 */
	int (*link_add)(void *priv, u8 link_id, const u8 *addr, void *bss_ctx);

	/**
	 * link_remove - Remove a link from the AP MLD interface
	 * @priv: Private driver interface data
	 * @type: Interface type
	 * @ifname: Interface name of the virtual interface from where the link
	 *	is to be removed.
	 * @link_id: Valid link ID to remove
	 * Returns: 0 on success, -1 on failure
	 */
	int (*link_remove)(void *priv, enum wpa_driver_if_type type,
			   const char *ifname, u8 link_id);

	/**
	 * is_drv_shared - Check whether the driver interface is shared
	 * @priv: Private driver interface data from init()
	 * @bss_ctx: BSS context for %WPA_IF_AP_BSS interfaces
	 *
	 * Checks whether the driver interface is being used by other partner
	 * BSS(s) or not. This is used to decide whether the driver interface
	 * needs to be deinitilized when one interface is getting deinitialized.
	 *
	 * Returns: true if it is being used or else false.
	 */
	bool (*is_drv_shared)(void *priv, void *bss_ctx);

	/**
	 * link_sta_remove - Remove a link STA from an MLD STA
	 * @priv: Private driver interface data
	 * @link_id: The link ID which the link STA is using
	 * @addr: The MLD MAC address of the MLD STA
	 * Returns: 0 on success, negative value on failure
	 */
	int (*link_sta_remove)(void *priv, u8 link_id, const u8 *addr);

#ifdef CONFIG_TESTING_OPTIONS
	int (*register_frame)(void *priv, u16 type,
			      const u8 *match, size_t match_len,
			      bool multicast);
#endif /* CONFIG_TESTING_OPTIONS */
};

/**
 * enum wpa_event_type - Event type for wpa_supplicant_event() calls
 */
enum wpa_event_type {
	/**
	 * EVENT_ASSOC - Association completed
	 *
	 * This event needs to be delivered when the driver completes IEEE
	 * 802.11 association or reassociation successfully.
	 * wpa_driver_ops::get_bssid() is expected to provide the current BSSID
	 * after this event has been generated. In addition, optional
	 * EVENT_ASSOCINFO may be generated just before EVENT_ASSOC to provide
	 * more information about the association. If the driver interface gets
	 * both of these events at the same time, it can also include the
	 * assoc_info data in EVENT_ASSOC call.
	 */
	EVENT_ASSOC,

	/**
	 * EVENT_DISASSOC - Association lost
	 *
	 * This event should be called when association is lost either due to
	 * receiving deauthenticate or disassociate frame from the AP or when
	 * sending either of these frames to the current AP. If the driver
	 * supports separate deauthentication event, EVENT_DISASSOC should only
	 * be used for disassociation and EVENT_DEAUTH for deauthentication.
	 * In AP mode, union wpa_event_data::disassoc_info is required.
	 */
	EVENT_DISASSOC,

	/**
	 * EVENT_MICHAEL_MIC_FAILURE - Michael MIC (TKIP) detected
	 *
	 * This event must be delivered when a Michael MIC error is detected by
	 * the local driver. Additional data for event processing is
	 * provided with union wpa_event_data::michael_mic_failure. This
	 * information is used to request new encryption key and to initiate
	 * TKIP countermeasures if needed.
	 */
	EVENT_MICHAEL_MIC_FAILURE,

	/**
	 * EVENT_SCAN_RESULTS - Scan results available
	 *
	 * This event must be called whenever scan results are available to be
	 * fetched with struct wpa_driver_ops::get_scan_results(). This event
	 * is expected to be used some time after struct wpa_driver_ops::scan()
	 * is called. If the driver provides an unsolicited event when the scan
	 * has been completed, this event can be used to trigger
	 * EVENT_SCAN_RESULTS call. If such event is not available from the
	 * driver, the driver wrapper code is expected to use a registered
	 * timeout to generate EVENT_SCAN_RESULTS call after the time that the
	 * scan is expected to be completed. Optional information about
	 * completed scan can be provided with union wpa_event_data::scan_info.
	 */
	EVENT_SCAN_RESULTS,

	/**
	 * EVENT_ASSOCINFO - Report optional extra information for association
	 *
	 * This event can be used to report extra association information for
	 * EVENT_ASSOC processing. This extra information includes IEs from
	 * association frames and Beacon/Probe Response frames in union
	 * wpa_event_data::assoc_info. EVENT_ASSOCINFO must be send just before
	 * EVENT_ASSOC. Alternatively, the driver interface can include
	 * assoc_info data in the EVENT_ASSOC call if it has all the
	 * information available at the same point.
	 */
	EVENT_ASSOCINFO,

	/**
	 * EVENT_INTERFACE_STATUS - Report interface status changes
	 *
	 * This optional event can be used to report changes in interface
	 * status (interface added/removed) using union
	 * wpa_event_data::interface_status. This can be used to trigger
	 * wpa_supplicant to stop and re-start processing for the interface,
	 * e.g., when a cardbus card is ejected/inserted.
	 */
	EVENT_INTERFACE_STATUS,

	/**
	 * EVENT_PMKID_CANDIDATE - Report a candidate AP for pre-authentication
	 *
	 * This event can be used to inform wpa_supplicant about candidates for
	 * RSN (WPA2) pre-authentication. If wpa_supplicant is not responsible
	 * for scan request (ap_scan=2 mode), this event is required for
	 * pre-authentication. If wpa_supplicant is performing scan request
	 * (ap_scan=1), this event is optional since scan results can be used
	 * to add pre-authentication candidates. union
	 * wpa_event_data::pmkid_candidate is used to report the BSSID of the
	 * candidate and priority of the candidate, e.g., based on the signal
	 * strength, in order to try to pre-authenticate first with candidates
	 * that are most likely targets for re-association.
	 *
	 * EVENT_PMKID_CANDIDATE can be called whenever the driver has updates
	 * on the candidate list. In addition, it can be called for the current
	 * AP and APs that have existing PMKSA cache entries. wpa_supplicant
	 * will automatically skip pre-authentication in cases where a valid
	 * PMKSA exists. When more than one candidate exists, this event should
	 * be generated once for each candidate.
	 *
	 * Driver will be notified about successful pre-authentication with
	 * struct wpa_driver_ops::add_pmkid() calls.
	 */
	EVENT_PMKID_CANDIDATE,

	/**
	 * EVENT_TDLS - Request TDLS operation
	 *
	 * This event can be used to request a TDLS operation to be performed.
	 */
	EVENT_TDLS,

	/**
	 * EVENT_FT_RESPONSE - Report FT (IEEE 802.11r) response IEs
	 *
	 * The driver is expected to report the received FT IEs from
	 * FT authentication sequence from the AP. The FT IEs are included in
	 * the extra information in union wpa_event_data::ft_ies.
	 */
	EVENT_FT_RESPONSE,

	/**
	 * EVENT_IBSS_RSN_START - Request RSN authentication in IBSS
	 *
	 * The driver can use this event to inform wpa_supplicant about a STA
	 * in an IBSS with which protected frames could be exchanged. This
	 * event starts RSN authentication with the other STA to authenticate
	 * the STA and set up encryption keys with it.
	 */
	EVENT_IBSS_RSN_START,

	/**
	 * EVENT_AUTH - Authentication result
	 *
	 * This event should be called when authentication attempt has been
	 * completed. This is only used if the driver supports separate
	 * authentication step (struct wpa_driver_ops::authenticate).
	 * Information about authentication result is included in
	 * union wpa_event_data::auth.
	 */
	EVENT_AUTH,

	/**
	 * EVENT_DEAUTH - Authentication lost
	 *
	 * This event should be called when authentication is lost either due
	 * to receiving deauthenticate frame from the AP or when sending that
	 * frame to the current AP.
	 * In AP mode, union wpa_event_data::deauth_info is required.
	 */
	EVENT_DEAUTH,

	/**
	 * EVENT_ASSOC_REJECT - Association rejected
	 *
	 * This event should be called when (re)association attempt has been
	 * rejected by the AP. Information about the association response is
	 * included in union wpa_event_data::assoc_reject.
	 */
	EVENT_ASSOC_REJECT,

	/**
	 * EVENT_AUTH_TIMED_OUT - Authentication timed out
	 */
	EVENT_AUTH_TIMED_OUT,

	/**
	 * EVENT_ASSOC_TIMED_OUT - Association timed out
	 */
	EVENT_ASSOC_TIMED_OUT,

	/**
	 * EVENT_WPS_BUTTON_PUSHED - Report hardware push button press for WPS
	 */
	EVENT_WPS_BUTTON_PUSHED,

	/**
	 * EVENT_TX_STATUS - Report TX status
	 */
	EVENT_TX_STATUS,

	/**
	 * EVENT_RX_FROM_UNKNOWN - Report RX from unknown STA
	 */
	EVENT_RX_FROM_UNKNOWN,

	/**
	 * EVENT_RX_MGMT - Report RX of a management frame
	 */
	EVENT_RX_MGMT,

	/**
	 * EVENT_REMAIN_ON_CHANNEL - Remain-on-channel duration started
	 *
	 * This event is used to indicate when the driver has started the
	 * requested remain-on-channel duration. Information about the
	 * operation is included in union wpa_event_data::remain_on_channel.
	 */
	EVENT_REMAIN_ON_CHANNEL,

	/**
	 * EVENT_CANCEL_REMAIN_ON_CHANNEL - Remain-on-channel timed out
	 *
	 * This event is used to indicate when the driver has completed
	 * remain-on-channel duration, i.e., may noot be available on the
	 * requested channel anymore. Information about the
	 * operation is included in union wpa_event_data::remain_on_channel.
	 */
	EVENT_CANCEL_REMAIN_ON_CHANNEL,

	/**
	 * EVENT_RX_PROBE_REQ - Indicate received Probe Request frame
	 *
	 * This event is used to indicate when a Probe Request frame has been
	 * received. Information about the received frame is included in
	 * union wpa_event_data::rx_probe_req. The driver is required to report
	 * these events only after successfully completed probe_req_report()
	 * commands to request the events (i.e., report parameter is non-zero)
	 * in station mode. In AP mode, Probe Request frames should always be
	 * reported.
	 */
	EVENT_RX_PROBE_REQ,

	/**
	 * EVENT_NEW_STA - New wired device noticed
	 *
	 * This event is used to indicate that a new device has been detected
	 * in a network that does not use association-like functionality (i.e.,
	 * mainly wired Ethernet). This can be used to start EAPOL
	 * authenticator when receiving a frame from a device. The address of
	 * the device is included in union wpa_event_data::new_sta.
	 */
	EVENT_NEW_STA,

	/**
	 * EVENT_EAPOL_RX - Report received EAPOL frame
	 *
	 * When in AP mode with hostapd, this event is required to be used to
	 * deliver the receive EAPOL frames from the driver.
	 */
	EVENT_EAPOL_RX,

	/**
	 * EVENT_SIGNAL_CHANGE - Indicate change in signal strength
	 *
	 * This event is used to indicate changes in the signal strength
	 * observed in frames received from the current AP if signal strength
	 * monitoring has been enabled with signal_monitor().
	 */
	EVENT_SIGNAL_CHANGE,

	/**
	 * EVENT_INTERFACE_ENABLED - Notify that interface was enabled
	 *
	 * This event is used to indicate that the interface was enabled after
	 * having been previously disabled, e.g., due to rfkill.
	 */
	EVENT_INTERFACE_ENABLED,

	/**
	 * EVENT_INTERFACE_DISABLED - Notify that interface was disabled
	 *
	 * This event is used to indicate that the interface was disabled,
	 * e.g., due to rfkill.
	 */
	EVENT_INTERFACE_DISABLED,

	/**
	 * EVENT_CHANNEL_LIST_CHANGED - Channel list changed
	 *
	 * This event is used to indicate that the channel list has changed,
	 * e.g., because of a regulatory domain change triggered by scan
	 * results including an AP advertising a country code.
	 */
	EVENT_CHANNEL_LIST_CHANGED,

	/**
	 * EVENT_INTERFACE_UNAVAILABLE - Notify that interface is unavailable
	 *
	 * This event is used to indicate that the driver cannot maintain this
	 * interface in its operation mode anymore. The most likely use for
	 * this is to indicate that AP mode operation is not available due to
	 * operating channel would need to be changed to a DFS channel when
	 * the driver does not support radar detection and another virtual
	 * interfaces caused the operating channel to change. Other similar
	 * resource conflicts could also trigger this for station mode
	 * interfaces. This event can be propagated when channel switching
	 * fails.
	 */
	EVENT_INTERFACE_UNAVAILABLE,

	/**
	 * EVENT_BEST_CHANNEL
	 *
	 * Driver generates this event whenever it detects a better channel
	 * (e.g., based on RSSI or channel use). This information can be used
	 * to improve channel selection for a new AP/P2P group.
	 */
	EVENT_BEST_CHANNEL,

	/**
	 * EVENT_UNPROT_DEAUTH - Unprotected Deauthentication frame received
	 *
	 * This event should be called when a Deauthentication frame is dropped
	 * due to it not being protected (MFP/IEEE 802.11w).
	 * union wpa_event_data::unprot_deauth is required to provide more
	 * details of the frame.
	 */
	EVENT_UNPROT_DEAUTH,

	/**
	 * EVENT_UNPROT_DISASSOC - Unprotected Disassociation frame received
	 *
	 * This event should be called when a Disassociation frame is dropped
	 * due to it not being protected (MFP/IEEE 802.11w).
	 * union wpa_event_data::unprot_disassoc is required to provide more
	 * details of the frame.
	 */
	EVENT_UNPROT_DISASSOC,

	/**
	 * EVENT_STATION_LOW_ACK
	 *
	 * Driver generates this event whenever it detected that a particular
	 * station was lost. Detection can be through massive transmission
	 * failures for example.
	 */
	EVENT_STATION_LOW_ACK,

	/**
	 * EVENT_IBSS_PEER_LOST - IBSS peer not reachable anymore
	 */
	EVENT_IBSS_PEER_LOST,

	/**
	 * EVENT_DRIVER_GTK_REKEY - Device/driver did GTK rekey
	 *
	 * This event carries the new replay counter to notify wpa_supplicant
	 * of the current EAPOL-Key Replay Counter in case the driver/firmware
	 * completed Group Key Handshake while the host (including
	 * wpa_supplicant was sleeping).
	 */
	EVENT_DRIVER_GTK_REKEY,

	/**
	 * EVENT_SCHED_SCAN_STOPPED - Scheduled scan was stopped
	 */
	EVENT_SCHED_SCAN_STOPPED,

	/**
	 * EVENT_DRIVER_CLIENT_POLL_OK - Station responded to poll
	 *
	 * This event indicates that the station responded to the poll
	 * initiated with @poll_client.
	 */
	EVENT_DRIVER_CLIENT_POLL_OK,

	/**
	 * EVENT_EAPOL_TX_STATUS - notify of EAPOL TX status
	 */
	EVENT_EAPOL_TX_STATUS,

	/**
	 * EVENT_CH_SWITCH - AP or GO decided to switch channels
	 *
	 * Described in wpa_event_data.ch_switch
	 * */
	EVENT_CH_SWITCH,

	/**
	 * EVENT_CH_SWITCH_STARTED - AP or GO started to switch channels
	 *
	 * This is a pre-switch event indicating the shortly following switch
	 * of operating channels.
	 *
	 * Described in wpa_event_data.ch_switch
	 */
	EVENT_CH_SWITCH_STARTED,
	/**
	 * EVENT_WNM - Request WNM operation
	 *
	 * This event can be used to request a WNM operation to be performed.
	 */
	EVENT_WNM,

	/**
	 * EVENT_CONNECT_FAILED_REASON - Connection failure reason in AP mode
	 *
	 * This event indicates that the driver reported a connection failure
	 * with the specified client (for example, max client reached, etc.) in
	 * AP mode.
	 */
	EVENT_CONNECT_FAILED_REASON,

	/**
	 * EVENT_DFS_RADAR_DETECTED - Notify of radar detection
	 *
	 * A radar has been detected on the supplied frequency, hostapd should
	 * react accordingly (e.g., change channel).
	 */
	EVENT_DFS_RADAR_DETECTED,

	/**
	 * EVENT_DFS_CAC_FINISHED - Notify that channel availability check has been completed
	 *
	 * After a successful CAC, the channel can be marked clear and used.
	 */
	EVENT_DFS_CAC_FINISHED,

	/**
	 * EVENT_DFS_CAC_ABORTED - Notify that channel availability check has been aborted
	 *
	 * The CAC was not successful, and the channel remains in the previous
	 * state. This may happen due to a radar being detected or other
	 * external influences.
	 */
	EVENT_DFS_CAC_ABORTED,

	/**
	 * EVENT_DFS_NOP_FINISHED - Notify that non-occupancy period is over
	 *
	 * The channel which was previously unavailable is now available again.
	 */
	EVENT_DFS_NOP_FINISHED,

	/**
	 * EVENT_SURVEY - Received survey data
	 *
	 * This event gets triggered when a driver query is issued for survey
	 * data and the requested data becomes available. The returned data is
	 * stored in struct survey_results. The results provide at most one
	 * survey entry for each frequency and at minimum will provide one
	 * survey entry for one frequency. The survey data can be os_malloc()'d
	 * and then os_free()'d, so the event callback must only copy data.
	 */
	EVENT_SURVEY,

	/**
	 * EVENT_SCAN_STARTED - Scan started
	 *
	 * This indicates that driver has started a scan operation either based
	 * on a request from wpa_supplicant/hostapd or from another application.
	 * EVENT_SCAN_RESULTS is used to indicate when the scan has been
	 * completed (either successfully or by getting cancelled).
	 */
	EVENT_SCAN_STARTED,

	/**
	 * EVENT_AVOID_FREQUENCIES - Received avoid frequency range
	 *
	 * This event indicates a set of frequency ranges that should be avoided
	 * to reduce issues due to interference or internal co-existence
	 * information in the driver.
	 */
	EVENT_AVOID_FREQUENCIES,

	/**
	 * EVENT_NEW_PEER_CANDIDATE - new (unknown) mesh peer notification
	 */
	EVENT_NEW_PEER_CANDIDATE,

	/**
	 * EVENT_ACS_CHANNEL_SELECTED - Received selected channels by ACS
	 *
	 * Indicates a pair of primary and secondary channels chosen by ACS
	 * in device.
	 */
	EVENT_ACS_CHANNEL_SELECTED,

	/**
	 * EVENT_DFS_CAC_STARTED - Notify that channel availability check has
	 * been started.
	 *
	 * This event indicates that channel availability check has been started
	 * on a DFS frequency by a driver that supports DFS Offload.
	 */
	EVENT_DFS_CAC_STARTED,

	/**
	 * EVENT_P2P_LO_STOP - Notify that P2P listen offload is stopped
	 */
	EVENT_P2P_LO_STOP,

	/**
	 * EVENT_BEACON_LOSS - Beacon loss detected
	 *
	 * This event indicates that no Beacon frames has been received from
	 * the current AP. This may indicate that the AP is not anymore in
	 * range.
	 */
	EVENT_BEACON_LOSS,

	/**
	 * EVENT_DFS_PRE_CAC_EXPIRED - Notify that channel availability check
	 * done previously (Pre-CAC) on the channel has expired. This would
	 * normally be on a non-ETSI DFS regulatory domain. DFS state of the
	 * channel will be moved from available to usable. A new CAC has to be
	 * performed before start operating on this channel.
	 */
	EVENT_DFS_PRE_CAC_EXPIRED,

	/**
	 * EVENT_EXTERNAL_AUTH - This event interface is used by host drivers
	 * that do not define separate commands for authentication and
	 * association (~WPA_DRIVER_FLAGS_SME) but offload the 802.11
	 * authentication to wpa_supplicant. This event carries all the
	 * necessary information from the host driver for the authentication to
	 * happen.
	 */
	EVENT_EXTERNAL_AUTH,

	/**
	 * EVENT_PORT_AUTHORIZED - Notification that a connection is authorized
	 *
	 * This event should be indicated when the driver completes the 4-way
	 * handshake. This event should be preceded by an EVENT_ASSOC that
	 * indicates the completion of IEEE 802.11 association.
	 */
	EVENT_PORT_AUTHORIZED,

	/**
	 * EVENT_STATION_OPMODE_CHANGED - Notify STA's HT/VHT operation mode
	 * change event.
	 */
	EVENT_STATION_OPMODE_CHANGED,

	/**
	 * EVENT_INTERFACE_MAC_CHANGED - Notify that interface MAC changed
	 *
	 * This event is emitted when the MAC changes while the interface is
	 * enabled. When an interface was disabled and becomes enabled, it
	 * must be always assumed that the MAC possibly changed.
	 */
	EVENT_INTERFACE_MAC_CHANGED,

	/**
	 * EVENT_WDS_STA_INTERFACE_STATUS - Notify WDS STA interface status
	 *
	 * This event is emitted when an interface is added/removed for WDS STA.
	 */
	EVENT_WDS_STA_INTERFACE_STATUS,

	/**
	  * EVENT_UPDATE_DH - Notification of updated DH information
	  */
	EVENT_UPDATE_DH,

	/**
	 * EVENT_UNPROT_BEACON - Unprotected Beacon frame received
	 *
	 * This event should be called when a Beacon frame is dropped due to it
	 * not being protected correctly. union wpa_event_data::unprot_beacon
	 * is required to provide more details of the frame.
	 */
	EVENT_UNPROT_BEACON,

	/**
	 * EVENT_TX_WAIT_EXPIRE - TX wait timed out
	 *
	 * This event is used to indicate when the driver has completed
	 * wait for a response frame based on a TX request that specified a
	 * non-zero wait time and that has not been explicitly cancelled.
	 */
	EVENT_TX_WAIT_EXPIRE,

	/**
	  * EVENT_BSS_COLOR_COLLISION - Notification of a BSS color collision
	  */
	EVENT_BSS_COLOR_COLLISION,

	/**
	 * EVENT_CCA_STARTED_NOTIFY - Notification that CCA has started
	 */
	EVENT_CCA_STARTED_NOTIFY,

	/**
	 * EVENT_CCA_ABORTED_NOTIFY - Notification that CCA has aborted
	 */
	EVENT_CCA_ABORTED_NOTIFY,

	/**
	 * EVENT_CCA_NOTIFY - Notification that CCA has completed
	 */
	EVENT_CCA_NOTIFY,

	/**
	 * EVENT_PASN_AUTH - This event is used by the driver that requests
	 * PASN authentication and secure ranging context for multiple peers.
	 */
	EVENT_PASN_AUTH,

	/**
	 * EVENT_LINK_CH_SWITCH - MLD AP link decided to switch channels
	 *
	 * Described in wpa_event_data.ch_switch.
	 *
	 */
	EVENT_LINK_CH_SWITCH,

	/**
	 * EVENT_LINK_CH_SWITCH_STARTED - MLD AP link started to switch channels
	 *
	 * This is a pre-switch event indicating the shortly following switch
	 * of operating channels.
	 *
	 * Described in wpa_event_data.ch_switch.
	 */
	EVENT_LINK_CH_SWITCH_STARTED,

	/**
	 * EVENT_TID_LINK_MAP - MLD event to set TID-to-link mapping
	 *
	 * This event is used by the driver to indicate the received TID-to-link
	 * mapping response from the associated AP MLD.
	 *
	 * Described in wpa_event_data.t2l_map_info.
	 */
	EVENT_TID_LINK_MAP,

	/**
	 * EVENT_LINK_RECONFIG - Notification that AP links removed
	 */
	EVENT_LINK_RECONFIG,
};


/**
 * struct freq_survey - Channel survey info
 *
 * @ifidx: Interface index in which this survey was observed
 * @freq: Center of frequency of the surveyed channel
 * @nf: Channel noise floor in dBm
 * @channel_time: Amount of time in ms the radio spent on the channel
 * @channel_time_busy: Amount of time in ms the radio detected some signal
 *     that indicated to the radio the channel was not clear
 * @channel_time_rx: Amount of time the radio spent receiving data
 * @channel_time_tx: Amount of time the radio spent transmitting data
 * @filled: bitmask indicating which fields have been reported, see
 *     SURVEY_HAS_* defines.
 * @list: Internal list pointers
 */
struct freq_survey {
	u32 ifidx;
	unsigned int freq;
	s8 nf;
	u64 channel_time;
	u64 channel_time_busy;
	u64 channel_time_rx;
	u64 channel_time_tx;
	unsigned int filled;
	struct dl_list list;
};

#define SURVEY_HAS_NF BIT(0)
#define SURVEY_HAS_CHAN_TIME BIT(1)
#define SURVEY_HAS_CHAN_TIME_BUSY BIT(2)
#define SURVEY_HAS_CHAN_TIME_RX BIT(3)
#define SURVEY_HAS_CHAN_TIME_TX BIT(4)

/**
 * enum sta_connect_fail_reason_codes - STA connect failure reason code values
 * @STA_CONNECT_FAIL_REASON_UNSPECIFIED: No reason code specified for
 *	connection failure.
 * @STA_CONNECT_FAIL_REASON_NO_BSS_FOUND: No Probe Response frame received
 *	for unicast Probe Request frame.
 * @STA_CONNECT_FAIL_REASON_AUTH_TX_FAIL: STA failed to send auth request.
 * @STA_CONNECT_FAIL_REASON_AUTH_NO_ACK_RECEIVED: AP didn't send ACK for
 *	auth request.
 * @STA_CONNECT_FAIL_REASON_AUTH_NO_RESP_RECEIVED: Auth response is not
 *	received from AP.
 * @STA_CONNECT_FAIL_REASON_ASSOC_REQ_TX_FAIL: STA failed to send
 *	Association Request frame.
 * @STA_CONNECT_FAIL_REASON_ASSOC_NO_ACK_RECEIVED: AP didn't send ACK for
 *	Association Request frame.
 * @STA_CONNECT_FAIL_REASON_ASSOC_NO_RESP_RECEIVED: Association Response
 *	frame is not received from AP.
 */
enum sta_connect_fail_reason_codes {
	STA_CONNECT_FAIL_REASON_UNSPECIFIED = 0,
	STA_CONNECT_FAIL_REASON_NO_BSS_FOUND = 1,
	STA_CONNECT_FAIL_REASON_AUTH_TX_FAIL = 2,
	STA_CONNECT_FAIL_REASON_AUTH_NO_ACK_RECEIVED = 3,
	STA_CONNECT_FAIL_REASON_AUTH_NO_RESP_RECEIVED = 4,
	STA_CONNECT_FAIL_REASON_ASSOC_REQ_TX_FAIL = 5,
	STA_CONNECT_FAIL_REASON_ASSOC_NO_ACK_RECEIVED = 6,
	STA_CONNECT_FAIL_REASON_ASSOC_NO_RESP_RECEIVED = 7,
};

/**
 * union wpa_event_data - Additional data for wpa_supplicant_event() calls
 */
union wpa_event_data {
	/**
	 * struct assoc_info - Data for EVENT_ASSOC and EVENT_ASSOCINFO events
	 *
	 * This structure is optional for EVENT_ASSOC calls and required for
	 * EVENT_ASSOCINFO calls. By using EVENT_ASSOC with this data, the
	 * driver interface does not need to generate separate EVENT_ASSOCINFO
	 * calls.
	 */
	struct assoc_info {
		/**
		 * reassoc - Flag to indicate association or reassociation
		 */
		int reassoc;

		/**
		 * req_ies - (Re)Association Request IEs
		 *
		 * If the driver generates WPA/RSN IE, this event data must be
		 * returned for WPA handshake to have needed information. If
		 * wpa_supplicant-generated WPA/RSN IE is used, this
		 * information event is optional.
		 *
		 * This should start with the first IE (fixed fields before IEs
		 * are not included).
		 */
		const u8 *req_ies;

		/**
		 * req_ies_len - Length of req_ies in bytes
		 */
		size_t req_ies_len;

		/**
		 * resp_ies - (Re)Association Response IEs
		 *
		 * Optional association data from the driver. This data is not
		 * required WPA, but may be useful for some protocols and as
		 * such, should be reported if this is available to the driver
		 * interface.
		 *
		 * This should start with the first IE (fixed fields before IEs
		 * are not included).
		 */
		const u8 *resp_ies;

		/**
		 * resp_ies_len - Length of resp_ies in bytes
		 */
		size_t resp_ies_len;

		/**
		 * resp_frame - (Re)Association Response frame
		 */
		const u8 *resp_frame;

		/**
		 * resp_frame_len - (Re)Association Response frame length
		 */
		size_t resp_frame_len;

		/**
		 * beacon_ies - Beacon or Probe Response IEs
		 *
		 * Optional Beacon/ProbeResp data: IEs included in Beacon or
		 * Probe Response frames from the current AP (i.e., the one
		 * that the client just associated with). This information is
		 * used to update WPA/RSN IE for the AP. If this field is not
		 * set, the results from previous scan will be used. If no
		 * data for the new AP is found, scan results will be requested
		 * again (without scan request). At this point, the driver is
		 * expected to provide WPA/RSN IE for the AP (if WPA/WPA2 is
		 * used).
		 *
		 * This should start with the first IE (fixed fields before IEs
		 * are not included).
		 */
		const u8 *beacon_ies;

		/**
		 * beacon_ies_len - Length of beacon_ies */
		size_t beacon_ies_len;

		/**
		 * freq - Frequency of the operational channel in MHz
		 */
		unsigned int freq;

		/**
		 * wmm_params - WMM parameters used in this association.
		 */
		struct wmm_params wmm_params;

		/**
		 * addr - Station address (for AP mode)
		 */
		const u8 *addr;

		/**
		 * The following is the key management offload information
		 * @authorized
		 * @key_replay_ctr
		 * @key_replay_ctr_len
		 * @ptk_kck
		 * @ptk_kek_len
		 * @ptk_kek
		 * @ptk_kek_len
		 */

		/**
		 * authorized - Status of key management offload,
		 * 1 = successful
		 */
		int authorized;

		/**
		 * key_replay_ctr - Key replay counter value last used
		 * in a valid EAPOL-Key frame
		 */
		const u8 *key_replay_ctr;

		/**
		 * key_replay_ctr_len - The length of key_replay_ctr
		 */
		size_t key_replay_ctr_len;

		/**
		 * ptk_kck - The derived PTK KCK
		 */
		const u8 *ptk_kck;

		/**
		 * ptk_kek_len - The length of ptk_kck
		 */
		size_t ptk_kck_len;

		/**
		 * ptk_kek - The derived PTK KEK
		 * This is used in key management offload and also in FILS SK
		 * offload.
		 */
		const u8 *ptk_kek;

		/**
		 * ptk_kek_len - The length of ptk_kek
		 */
		size_t ptk_kek_len;

		/**
		 * subnet_status - The subnet status:
		 * 0 = unknown, 1 = unchanged, 2 = changed
		 */
		u8 subnet_status;

		/**
		 * The following information is used in FILS SK offload
		 * @fils_erp_next_seq_num
		 * @fils_pmk
		 * @fils_pmk_len
		 * @fils_pmkid
		 */

		/**
		 * fils_erp_next_seq_num - The next sequence number to use in
		 * FILS ERP messages
		 */
		u16 fils_erp_next_seq_num;

		/**
		 * fils_pmk - A new PMK if generated in case of FILS
		 * authentication
		 */
		const u8 *fils_pmk;

		/**
		 * fils_pmk_len - Length of fils_pmk
		 */
		size_t fils_pmk_len;

		/**
		 * fils_pmkid - PMKID used or generated in FILS authentication
		 */
		const u8 *fils_pmkid;

		/**
		 * link_addr - Link address of the STA
		 */
		const u8 *link_addr;

		/**
		 * assoc_link_id - Association link id of the MLO association or
		 *	-1 if MLO is not used
		 */
		int assoc_link_id;
	} assoc_info;

	/**
	 * struct disassoc_info - Data for EVENT_DISASSOC events
	 */
	struct disassoc_info {
		/**
		 * addr - Station address (for AP mode)
		 */
		const u8 *addr;

		/**
		 * reason_code - Reason Code (host byte order) used in
		 *	Deauthentication frame
		 */
		u16 reason_code;

		/**
		 * ie - Optional IE(s) in Disassociation frame
		 */
		const u8 *ie;

		/**
		 * ie_len - Length of ie buffer in octets
		 */
		size_t ie_len;

		/**
		 * locally_generated - Whether the frame was locally generated
		 */
		int locally_generated;
	} disassoc_info;

	/**
	 * struct deauth_info - Data for EVENT_DEAUTH events
	 */
	struct deauth_info {
		/**
		 * addr - Station address (for AP mode)
		 */
		const u8 *addr;

		/**
		 * reason_code - Reason Code (host byte order) used in
		 *	Deauthentication frame
		 */
		u16 reason_code;

		/**
		 * ie - Optional IE(s) in Deauthentication frame
		 */
		const u8 *ie;

		/**
		 * ie_len - Length of ie buffer in octets
		 */
		size_t ie_len;

		/**
		 * locally_generated - Whether the frame was locally generated
		 */
		int locally_generated;
	} deauth_info;

	/**
	 * struct michael_mic_failure - Data for EVENT_MICHAEL_MIC_FAILURE
	 */
	struct michael_mic_failure {
		int unicast;
		const u8 *src;
	} michael_mic_failure;

	/**
	 * struct interface_status - Data for EVENT_INTERFACE_STATUS
	 */
	struct interface_status {
		unsigned int ifindex;
		char ifname[100];
		enum {
			EVENT_INTERFACE_ADDED, EVENT_INTERFACE_REMOVED
		} ievent;
	} interface_status;

	/**
	 * struct pmkid_candidate - Data for EVENT_PMKID_CANDIDATE
	 */
	struct pmkid_candidate {
		/** BSSID of the PMKID candidate */
		u8 bssid[ETH_ALEN];
		/** Smaller the index, higher the priority */
		int index;
		/** Whether RSN IE includes pre-authenticate flag */
		int preauth;
	} pmkid_candidate;

	/**
	 * struct tdls - Data for EVENT_TDLS
	 */
	struct tdls {
		u8 peer[ETH_ALEN];
		enum {
			TDLS_REQUEST_SETUP,
			TDLS_REQUEST_TEARDOWN,
			TDLS_REQUEST_DISCOVER,
		} oper;
		u16 reason_code; /* for teardown */
	} tdls;

	/**
	 * struct wnm - Data for EVENT_WNM
	 */
	struct wnm {
		u8 addr[ETH_ALEN];
		enum {
			WNM_OPER_SLEEP,
		} oper;
		enum {
			WNM_SLEEP_ENTER,
			WNM_SLEEP_EXIT
		} sleep_action;
		int sleep_intval;
		u16 reason_code;
		u8 *buf;
		u16 buf_len;
	} wnm;

	/**
	 * struct ft_ies - FT information elements (EVENT_FT_RESPONSE)
	 *
	 * During FT (IEEE 802.11r) authentication sequence, the driver is
	 * expected to use this event to report received FT IEs (MDIE, FTIE,
	 * RSN IE, TIE, possible resource request) to the supplicant. The FT
	 * IEs for the next message will be delivered through the
	 * struct wpa_driver_ops::update_ft_ies() callback.
	 */
	struct ft_ies {
		const u8 *ies;
		size_t ies_len;
		int ft_action;
		u8 target_ap[ETH_ALEN];
		/** Optional IE(s), e.g., WMM TSPEC(s), for RIC-Request */
		const u8 *ric_ies;
		/** Length of ric_ies buffer in octets */
		size_t ric_ies_len;
	} ft_ies;

	/**
	 * struct ibss_rsn_start - Data for EVENT_IBSS_RSN_START
	 */
	struct ibss_rsn_start {
		u8 peer[ETH_ALEN];
	} ibss_rsn_start;

	/**
	 * struct auth_info - Data for EVENT_AUTH events
	 */
	struct auth_info {
		u8 peer[ETH_ALEN];
		u8 bssid[ETH_ALEN];
		u16 auth_type;
		u16 auth_transaction;
		u16 status_code;
		const u8 *ies;
		size_t ies_len;
	} auth;

	/**
	 * struct assoc_reject - Data for EVENT_ASSOC_REJECT events
	 */
	struct assoc_reject {
		/**
		 * bssid - BSSID of the AP that rejected association
		 */
		const u8 *bssid;

		/**
		 * resp_ies - (Re)Association Response IEs
		 *
		 * Optional association data from the driver. This data is not
		 * required WPA, but may be useful for some protocols and as
		 * such, should be reported if this is available to the driver
		 * interface.
		 *
		 * This should start with the first IE (fixed fields before IEs
		 * are not included).
		 */
		const u8 *resp_ies;

		/**
		 * resp_ies_len - Length of resp_ies in bytes
		 */
		size_t resp_ies_len;

		/**
		 * status_code - Status Code from (Re)association Response
		 */
		u16 status_code;

		/**
		 * timed_out - Whether failure is due to timeout (etc.) rather
		 * than explicit rejection response from the AP.
		 */
		int timed_out;

		/**
		 * timeout_reason - Reason for the timeout
		 */
		const char *timeout_reason;

		/**
		 * fils_erp_next_seq_num - The next sequence number to use in
		 * FILS ERP messages
		 */
		u16 fils_erp_next_seq_num;

		/**
		 * reason_code - Connection failure reason code from the driver
		 */
		enum sta_connect_fail_reason_codes reason_code;
	} assoc_reject;

	struct timeout_event {
		u8 addr[ETH_ALEN];
	} timeout_event;

	/**
	 * struct tx_status - Data for EVENT_TX_STATUS events
	 */
	struct tx_status {
		u16 type;
		u16 stype;
		const u8 *dst;
		const u8 *data;
		size_t data_len;
		int ack;
		int link_id;
	} tx_status;

	/**
	 * struct rx_from_unknown - Data for EVENT_RX_FROM_UNKNOWN events
	 */
	struct rx_from_unknown {
		const u8 *bssid;
		const u8 *addr;
		int wds;
	} rx_from_unknown;

	/**
	 * struct rx_mgmt - Data for EVENT_RX_MGMT events
	 */
	struct rx_mgmt {
		const u8 *frame;
		size_t frame_len;
		u32 datarate;

		/**
		 * drv_priv - Pointer to store driver private BSS information
		 *
		 * If not set to NULL, this is used for comparison with
		 * hostapd_data->drv_priv to determine which BSS should process
		 * the frame.
		 */
		void *drv_priv;

		/**
		 * ctx - Pointer to store ctx of private BSS information
		 *
		 * If not set to NULL, this is used for forwarding the packet
		 * to right link BSS of ML BSS.
		 */
		void *ctx;

		/**
		 * freq - Frequency (in MHz) on which the frame was received
		 */
		int freq;

		/**
		 * ssi_signal - Signal strength in dBm (or 0 if not available)
		 */
		int ssi_signal;

		/**
		 * link_id - MLO link on which the frame was received or -1 for
		 * non MLD.
		 */
		int link_id;
	} rx_mgmt;

	/**
	 * struct remain_on_channel - Data for EVENT_REMAIN_ON_CHANNEL events
	 *
	 * This is also used with EVENT_CANCEL_REMAIN_ON_CHANNEL events.
	 */
	struct remain_on_channel {
		/**
		 * freq - Channel frequency in MHz
		 */
		unsigned int freq;

		/**
		 * duration - Duration to remain on the channel in milliseconds
		 */
		unsigned int duration;
	} remain_on_channel;

	/**
	 * struct scan_info - Optional data for EVENT_SCAN_RESULTS events
	 * @aborted: Whether the scan was aborted
	 * @freqs: Scanned frequencies in MHz (%NULL = all channels scanned)
	 * @num_freqs: Number of entries in freqs array
	 * @ssids: Scanned SSIDs (%NULL or zero-length SSID indicates wildcard
	 *	SSID)
	 * @num_ssids: Number of entries in ssids array
	 * @external_scan: Whether the scan info is for an external scan
	 * @nl_scan_event: 1 if the source of this scan event is a normal scan,
	 * 	0 if the source of the scan event is a vendor scan
	 * @scan_start_tsf: Time when the scan started in terms of TSF of the
	 *	BSS that the interface that requested the scan is connected to
	 *	(if available).
	 * @scan_start_tsf_bssid: The BSSID according to which %scan_start_tsf
	 *	is set.
	 * @scan_cookie: Unique identification representing the corresponding
	 *      scan request. 0 if no unique identification is available.
	 */
	struct scan_info {
		int aborted;
		const int *freqs;
		size_t num_freqs;
		struct wpa_driver_scan_ssid ssids[WPAS_MAX_SCAN_SSIDS];
		size_t num_ssids;
		int external_scan;
		int nl_scan_event;
		u64 scan_start_tsf;
		u8 scan_start_tsf_bssid[ETH_ALEN];
		u64 scan_cookie;
	} scan_info;

	/**
	 * struct rx_probe_req - Data for EVENT_RX_PROBE_REQ events
	 */
	struct rx_probe_req {
		/**
		 * sa - Source address of the received Probe Request frame
		 */
		const u8 *sa;

		/**
		 * da - Destination address of the received Probe Request frame
		 *	or %NULL if not available
		 */
		const u8 *da;

		/**
		 * bssid - BSSID of the received Probe Request frame or %NULL
		 *	if not available
		 */
		const u8 *bssid;

		/**
		 * ie - IEs from the Probe Request body
		 */
		const u8 *ie;

		/**
		 * ie_len - Length of ie buffer in octets
		 */
		size_t ie_len;

		/**
		 * signal - signal strength in dBm (or 0 if not available)
		 */
		int ssi_signal;
	} rx_probe_req;

	/**
	 * struct new_sta - Data for EVENT_NEW_STA events
	 */
	struct new_sta {
		const u8 *addr;
	} new_sta;

	/**
	 * struct eapol_rx - Data for EVENT_EAPOL_RX events
	 */
	struct eapol_rx {
		const u8 *src;
		const u8 *data;
		size_t data_len;
		enum frame_encryption encrypted;
		int link_id;
	} eapol_rx;

	/**
	 * signal_change - Data for EVENT_SIGNAL_CHANGE events
	 */
	struct wpa_signal_info signal_change;

	/**
	 * struct best_channel - Data for EVENT_BEST_CHANNEL events
	 * @freq_24: Best 2.4 GHz band channel frequency in MHz
	 * @freq_5: Best 5 GHz band channel frequency in MHz
	 * @freq_overall: Best channel frequency in MHz
	 *
	 * 0 can be used to indicate no preference in either band.
	 */
	struct best_channel {
		int freq_24;
		int freq_5;
		int freq_overall;
	} best_chan;

	struct unprot_deauth {
		const u8 *sa;
		const u8 *da;
		u16 reason_code;
	} unprot_deauth;

	struct unprot_disassoc {
		const u8 *sa;
		const u8 *da;
		u16 reason_code;
	} unprot_disassoc;

	/**
	 * struct low_ack - Data for EVENT_STATION_LOW_ACK events
	 * @addr: station address
	 * @num_packets: Number of packets lost (consecutive packets not
	 * acknowledged)
	 */
	struct low_ack {
		u8 addr[ETH_ALEN];
		u32 num_packets;
	} low_ack;

	/**
	 * struct ibss_peer_lost - Data for EVENT_IBSS_PEER_LOST
	 */
	struct ibss_peer_lost {
		u8 peer[ETH_ALEN];
	} ibss_peer_lost;

	/**
	 * struct driver_gtk_rekey - Data for EVENT_DRIVER_GTK_REKEY
	 */
	struct driver_gtk_rekey {
		const u8 *bssid;
		const u8 *replay_ctr;
	} driver_gtk_rekey;

	/**
	 * struct client_poll - Data for EVENT_DRIVER_CLIENT_POLL_OK events
	 * @addr: station address
	 */
	struct client_poll {
		u8 addr[ETH_ALEN];
	} client_poll;

	/**
	 * struct eapol_tx_status
	 * @dst: Original destination
	 * @data: Data starting with IEEE 802.1X header (!)
	 * @data_len: Length of data
	 * @ack: Indicates ack or lost frame
	 * @link_id: MLD link id used to transmit the frame or -1 for non MLO
	 *
	 * This corresponds to hapd_send_eapol if the frame sent
	 * there isn't just reported as EVENT_TX_STATUS.
	 */
	struct eapol_tx_status {
		const u8 *dst;
		const u8 *data;
		int data_len;
		int ack;
		int link_id;
	} eapol_tx_status;

	/**
	 * struct ch_switch
	 * @freq: Frequency of new channel in MHz
	 * @ht_enabled: Whether this is an HT channel
	 * @ch_offset: Secondary channel offset
	 * @ch_width: Channel width
	 * @cf1: Center frequency 1
	 * @cf2: Center frequency 2
	 * @link_id: Link ID of the MLO link
	 * @punct_bitmap: Puncturing bitmap
	 */
	struct ch_switch {
		int freq;
		int ht_enabled;
		int ch_offset;
		enum chan_width ch_width;
		int cf1;
		int cf2;
		int link_id;
		u16 punct_bitmap;
	} ch_switch;

	/**
	 * struct connect_failed - Data for EVENT_CONNECT_FAILED_REASON
	 * @addr: Remote client address
	 * @code: Reason code for connection failure
	 */
	struct connect_failed_reason {
		u8 addr[ETH_ALEN];
		enum {
			MAX_CLIENT_REACHED,
			BLOCKED_CLIENT
		} code;
	} connect_failed_reason;

	/**
	 * struct dfs_event - Data for radar detected events
	 * @freq: Frequency of the channel in MHz
	 * @link_id: If >= 0, Link ID of the MLO link
	 */
	struct dfs_event {
		int freq;
		int ht_enabled;
		int chan_offset;
		enum chan_width chan_width;
		int cf1;
		int cf2;
		int link_id;
	} dfs_event;

	/**
	 * survey_results - Survey result data for EVENT_SURVEY
	 * @freq_filter: Requested frequency survey filter, 0 if request
	 *	was for all survey data
	 * @survey_list: Linked list of survey data (struct freq_survey)
	 */
	struct survey_results {
		unsigned int freq_filter;
		struct dl_list survey_list; /* struct freq_survey */
	} survey_results;

	/**
	 * channel_list_changed - Data for EVENT_CHANNEL_LIST_CHANGED
	 * @initiator: Initiator of the regulatory change
	 * @type: Regulatory change type
	 * @alpha2: Country code (or "" if not available)
	 * @beacon_hint_before: Data for frequency attributes before beacon hint
	 *	event if initiator == REGDOM_BEACON_HINT
	 * @beacon_hint_after: Data for frequency attributes after beacon hint
	 *	event if initiator == REGDOM_BEACON_HINT
	 */
	struct channel_list_changed {
		enum reg_change_initiator initiator;
		enum reg_type type;
		char alpha2[3];
		struct frequency_attrs {
			unsigned int freq;
			unsigned int max_tx_power;
			bool disabled;
			bool no_ir;
			bool radar;
		} beacon_hint_before, beacon_hint_after;
	} channel_list_changed;

	/**
	 * freq_range - List of frequency ranges
	 *
	 * This is used as the data with EVENT_AVOID_FREQUENCIES.
	 */
	struct wpa_freq_range_list freq_range;

	/**
	 * struct mesh_peer
	 *
	 * @peer: Peer address
	 * @ies: Beacon IEs
	 * @ie_len: Length of @ies
	 *
	 * Notification of new candidate mesh peer.
	 */
	struct mesh_peer {
		const u8 *peer;
		const u8 *ies;
		size_t ie_len;
	} mesh_peer;

	/**
	 * struct acs_selected_channels - Data for EVENT_ACS_CHANNEL_SELECTED
	 * @pri_freq: Selected primary frequency
	 * @sec_freq: Selected secondary frequency
	 * @edmg_channel: Selected EDMG channel
	 * @vht_seg0_center_ch: VHT mode Segment0 center channel
	 *	The value is the index of the channel center frequency for
	 *	20 MHz, 40 MHz, and 80 MHz channels. The value is the center
	 *	frequency index of the primary 80 MHz segment for 160 MHz and
	 *	80+80 MHz channels.
	 * @vht_seg1_center_ch: VHT mode Segment1 center channel
	 *	The value is zero for 20 MHz, 40 MHz, and 80 MHz channels. The
	 *	value is the index of the channel center frequency for 160 MHz
	 *	channels and the center frequency index of the secondary 80 MHz
	 *	segment for 80+80 MHz channels.
	 * @ch_width: Selected Channel width by driver. Driver may choose to
	 *	change hostapd configured ACS channel width due driver internal
	 *	channel restrictions.
	 * @hw_mode: Selected band (used with hw_mode=any)
	 * @puncture_bitmap: Indicate the puncturing channels
	 * @link_id: Indicate the link id if operating as AP MLD; -1 otherwise
	 */
	struct acs_selected_channels {
		unsigned int pri_freq;
		unsigned int sec_freq;
		u8 edmg_channel;
		u8 vht_seg0_center_ch;
		u8 vht_seg1_center_ch;
		u16 ch_width;
		enum hostapd_hw_mode hw_mode;
		u16 puncture_bitmap;
		int link_id;
	} acs_selected_channels;

	/**
	 * struct p2p_lo_stop - Reason code for P2P Listen offload stop event
	 * @reason_code: Reason for stopping offload
	 *	P2P_LO_STOPPED_REASON_COMPLETE: Listen offload finished as
	 *	scheduled.
	 *	P2P_LO_STOPPED_REASON_RECV_STOP_CMD: Host requested offload to
	 *	be stopped.
	 *	P2P_LO_STOPPED_REASON_INVALID_PARAM: Invalid listen offload
	 *	parameters.
	 *	P2P_LO_STOPPED_REASON_NOT_SUPPORTED: Listen offload not
	 *	supported by device.
	 */
	struct p2p_lo_stop {
		enum {
			P2P_LO_STOPPED_REASON_COMPLETE = 0,
			P2P_LO_STOPPED_REASON_RECV_STOP_CMD,
			P2P_LO_STOPPED_REASON_INVALID_PARAM,
			P2P_LO_STOPPED_REASON_NOT_SUPPORTED,
		} reason_code;
	} p2p_lo_stop;

	/* For EVENT_EXTERNAL_AUTH */
	struct external_auth external_auth;

	/**
	 * struct sta_opmode - Station's operation mode change event
	 * @addr: The station MAC address
	 * @smps_mode: SMPS mode of the station
	 * @chan_width: Channel width of the station
	 * @rx_nss: RX_NSS of the station
	 *
	 * This is used as data with EVENT_STATION_OPMODE_CHANGED.
	 */
	struct sta_opmode {
		const u8 *addr;
		enum smps_mode smps_mode;
		enum chan_width chan_width;
		u8 rx_nss;
	} sta_opmode;

	/**
	 * struct wds_sta_interface - Data for EVENT_WDS_STA_INTERFACE_STATUS.
	 */
	struct wds_sta_interface {
		const u8 *sta_addr;
		const char *ifname;
		enum {
			INTERFACE_ADDED,
			INTERFACE_REMOVED
		} istatus;
	} wds_sta_interface;

	/**
	 * struct update_dh - Data for EVENT_UPDATE_DH
	 */
	struct update_dh {
		const u8 *peer;
		const u8 *ie;
		size_t ie_len;
		int assoc_link_id;
		const u8 *link_addr;
	} update_dh;

	/**
	 * struct unprot_beacon - Data for EVENT_UNPROT_BEACON
	 */
	struct unprot_beacon {
		const u8 *sa;
	} unprot_beacon;

	/**
	 * struct bss_color_collision - Data for EVENT_BSS_COLOR_COLLISION
	 */
	struct bss_color_collision {
		u64 bitmap;
		int link_id;
	} bss_color_collision;

	/**
	 * struct pasn_auth - Data for EVENT_PASN_AUTH
	 */
	struct pasn_auth pasn_auth;

	/**
	 * struct port_authorized - Data for EVENT_PORT_AUTHORIZED
	 * @td_bitmap: For STA mode, transition disable bitmap, if received in
	 *	EAPOL-Key msg 3/4
	 * @td_bitmap_len: For STA mode, length of td_bitmap
	 * @sta_addr: For AP mode, the MAC address of the associated STA
	 *
	 * This event is used to indicate that the port is authorized and
	 * open for normal data in STA and AP modes when 4-way handshake is
	 * offloaded to the driver.
	 */
	struct port_authorized {
		const u8 *td_bitmap;
		size_t td_bitmap_len;
		const u8 *sta_addr;
	} port_authorized;

	/**
	 * struct tid_link_map_info - Data for EVENT_TID_LINK_MAP
	 */
	struct tid_link_map_info {
		bool default_map;
		u8 valid_links;
		struct t2lm_mapping t2lmap[MAX_NUM_MLD_LINKS];
	} t2l_map_info;
};

/**
 * wpa_supplicant_event - Report a driver event for wpa_supplicant
 * @ctx: Context pointer (wpa_s); this is the ctx variable registered
 *	with struct wpa_driver_ops::init()
 * @event: event type (defined above)
 * @data: possible extra data for the event
 *
 * Driver wrapper code should call this function whenever an event is received
 * from the driver.
 */
void wpa_supplicant_event(void *ctx, enum wpa_event_type event,
			  union wpa_event_data *data);

/**
 * wpa_supplicant_event_global - Report a driver event for wpa_supplicant
 * @ctx: Context pointer (wpa_s); this is the ctx variable registered
 *	with struct wpa_driver_ops::init()
 * @event: event type (defined above)
 * @data: possible extra data for the event
 *
 * Same as wpa_supplicant_event(), but we search for the interface in
 * wpa_global.
 */
void wpa_supplicant_event_global(void *ctx, enum wpa_event_type event,
				 union wpa_event_data *data);

/*
 * The following inline functions are provided for convenience to simplify
 * event indication for some of the common events.
 */

static inline void drv_event_assoc(void *ctx, const u8 *addr, const u8 *req_ies,
				   size_t req_ielen, const u8 *resp_ies,
				   size_t resp_ielen, const u8 *link_addr,
				   int assoc_link_id, int reassoc)
{
	union wpa_event_data event;
	os_memset(&event, 0, sizeof(event));
	event.assoc_info.reassoc = reassoc;
	event.assoc_info.req_ies = req_ies;
	event.assoc_info.req_ies_len = req_ielen;
	event.assoc_info.resp_ies = resp_ies;
	event.assoc_info.resp_ies_len = resp_ielen;
	event.assoc_info.addr = addr;
	event.assoc_info.link_addr = link_addr;
	event.assoc_info.assoc_link_id = assoc_link_id;
	wpa_supplicant_event(ctx, EVENT_ASSOC, &event);
}

static inline void drv_event_disassoc(void *ctx, const u8 *addr)
{
	union wpa_event_data event;
	os_memset(&event, 0, sizeof(event));
	event.disassoc_info.addr = addr;
	wpa_supplicant_event(ctx, EVENT_DISASSOC, &event);
}

static inline void drv_event_eapol_rx(void *ctx, const u8 *src, const u8 *data,
				      size_t data_len)
{
	union wpa_event_data event;
	os_memset(&event, 0, sizeof(event));
	event.eapol_rx.src = src;
	event.eapol_rx.data = data;
	event.eapol_rx.data_len = data_len;
	event.eapol_rx.encrypted = FRAME_ENCRYPTION_UNKNOWN;
	event.eapol_rx.link_id = -1;
	wpa_supplicant_event(ctx, EVENT_EAPOL_RX, &event);
}

static inline void drv_event_eapol_rx2(void *ctx, const u8 *src, const u8 *data,
				       size_t data_len,
				       enum frame_encryption encrypted,
				       int link_id)
{
	union wpa_event_data event;
	os_memset(&event, 0, sizeof(event));
	event.eapol_rx.src = src;
	event.eapol_rx.data = data;
	event.eapol_rx.data_len = data_len;
	event.eapol_rx.encrypted = encrypted;
	event.eapol_rx.link_id = link_id;
	wpa_supplicant_event(ctx, EVENT_EAPOL_RX, &event);
}

/* driver_common.c */
void wpa_scan_results_free(struct wpa_scan_results *res);

/* Convert wpa_event_type to a string for logging */
const char * event_to_string(enum wpa_event_type event);

/* Convert chan_width to a string for logging and control interfaces */
const char * channel_width_to_string(enum chan_width width);

int channel_width_to_int(enum chan_width width);

int ht_supported(const struct hostapd_hw_modes *mode);
int vht_supported(const struct hostapd_hw_modes *mode);
bool he_supported(const struct hostapd_hw_modes *hw_mode,
		  enum ieee80211_op_mode op_mode);

struct wowlan_triggers *
wpa_get_wowlan_triggers(const char *wowlan_triggers,
			const struct wpa_driver_capa *capa);
/* Convert driver flag to string */
const char * driver_flag_to_string(u64 flag);
const char * driver_flag2_to_string(u64 flag2);

/* NULL terminated array of linked in driver wrappers */
extern const struct wpa_driver_ops *const wpa_drivers[];


/* Available drivers */

#ifdef CONFIG_DRIVER_WEXT
extern const struct wpa_driver_ops wpa_driver_wext_ops; /* driver_wext.c */
#endif /* CONFIG_DRIVER_WEXT */
#ifdef CONFIG_DRIVER_NL80211
/* driver_nl80211.c */
extern const struct wpa_driver_ops wpa_driver_nl80211_ops;
#endif /* CONFIG_DRIVER_NL80211 */
#ifdef CONFIG_DRIVER_HOSTAP
extern const struct wpa_driver_ops wpa_driver_hostap_ops; /* driver_hostap.c */
#endif /* CONFIG_DRIVER_HOSTAP */
#ifdef CONFIG_DRIVER_BSD
extern const struct wpa_driver_ops wpa_driver_bsd_ops; /* driver_bsd.c */
#endif /* CONFIG_DRIVER_BSD */
#ifdef CONFIG_DRIVER_OPENBSD
/* driver_openbsd.c */
extern const struct wpa_driver_ops wpa_driver_openbsd_ops;
#endif /* CONFIG_DRIVER_OPENBSD */
#ifdef CONFIG_DRIVER_NDIS
extern struct wpa_driver_ops wpa_driver_ndis_ops; /* driver_ndis.c */
#endif /* CONFIG_DRIVER_NDIS */
#ifdef CONFIG_DRIVER_WIRED
extern const struct wpa_driver_ops wpa_driver_wired_ops; /* driver_wired.c */
#endif /* CONFIG_DRIVER_WIRED */
#ifdef CONFIG_DRIVER_MACSEC_QCA
/* driver_macsec_qca.c */
extern const struct wpa_driver_ops wpa_driver_macsec_qca_ops;
#endif /* CONFIG_DRIVER_MACSEC_QCA */
#ifdef CONFIG_DRIVER_MACSEC_LINUX
/* driver_macsec_linux.c */
extern const struct wpa_driver_ops wpa_driver_macsec_linux_ops;
#endif /* CONFIG_DRIVER_MACSEC_LINUX */
#ifdef CONFIG_DRIVER_ROBOSWITCH
/* driver_roboswitch.c */
extern const struct wpa_driver_ops wpa_driver_roboswitch_ops;
#endif /* CONFIG_DRIVER_ROBOSWITCH */
#ifdef CONFIG_DRIVER_ATHEROS
/* driver_atheros.c */
extern const struct wpa_driver_ops wpa_driver_atheros_ops;
#endif /* CONFIG_DRIVER_ATHEROS */
#ifdef CONFIG_DRIVER_NONE
extern const struct wpa_driver_ops wpa_driver_none_ops; /* driver_none.c */
#endif /* CONFIG_DRIVER_NONE */

#endif /* DRIVER_H */