xref: /freebsd/sys/dev/aic7xxx/aic7770.c (revision 65971073)
1 /*-
2  * Product specific probe and attach routines for:
3  * 	27/284X and aic7770 motherboard SCSI controllers
4  *
5  * SPDX-License-Identifier: BSD-3-Clause
6  *
7  * Copyright (c) 1994-1998, 2000, 2001 Justin T. Gibbs.
8  * All rights reserved.
9  *
10  * Redistribution and use in source and binary forms, with or without
11  * modification, are permitted provided that the following conditions
12  * are met:
13  * 1. Redistributions of source code must retain the above copyright
14  *    notice, this list of conditions, and the following disclaimer,
15  *    without modification.
16  * 2. Redistributions in binary form must reproduce at minimum a disclaimer
17  *    substantially similar to the "NO WARRANTY" disclaimer below
18  *    ("Disclaimer") and any redistribution must be conditioned upon
19  *    including a substantially similar Disclaimer requirement for further
20  *    binary redistribution.
21  * 3. Neither the names of the above-listed copyright holders nor the names
22  *    of any contributors may be used to endorse or promote products derived
23  *    from this software without specific prior written permission.
24  *
25  * Alternatively, this software may be distributed under the terms of the
26  * GNU General Public License ("GPL") version 2 as published by the Free
27  * Software Foundation.
28  *
29  * NO WARRANTY
30  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
31  * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
32  * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
33  * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
34  * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
35  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
36  * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
37  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
38  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
39  * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
40  * POSSIBILITY OF SUCH DAMAGES.
41  *
42  * $Id: //depot/aic7xxx/aic7xxx/aic7770.c#34 $
43  */
44 
45 #include <dev/aic7xxx/aic7xxx_osm.h>
46 #include <dev/aic7xxx/aic7xxx_inline.h>
47 #include <dev/aic7xxx/aic7xxx_93cx6.h>
48 
49 #define ID_AIC7770	0x04907770
50 #define ID_AHA_274x	0x04907771
51 #define ID_AHA_284xB	0x04907756 /* BIOS enabled */
52 #define ID_AHA_284x	0x04907757 /* BIOS disabled*/
53 #define	ID_OLV_274x	0x04907782 /* Olivetti OEM */
54 #define	ID_OLV_274xD	0x04907783 /* Olivetti OEM (Differential) */
55 
56 static int aic7770_chip_init(struct ahc_softc *ahc);
57 static int aic7770_suspend(struct ahc_softc *ahc);
58 static int aic7770_resume(struct ahc_softc *ahc);
59 static int aha2840_load_seeprom(struct ahc_softc *ahc);
60 static ahc_device_setup_t ahc_aic7770_VL_setup;
61 static ahc_device_setup_t ahc_aic7770_EISA_setup;	/* Really just ISA */
62 static ahc_device_setup_t ahc_aic7770_setup;
63 
64 struct aic7770_identity aic7770_ident_table[] =
65 {
66 	{
67 		ID_AHA_274x,
68 		0xFFFFFFFF,
69 		"Adaptec 274X SCSI adapter",
70 		ahc_aic7770_EISA_setup
71 	},
72 	{
73 		ID_AHA_284xB,
74 		0xFFFFFFFE,
75 		"Adaptec 284X SCSI adapter",
76 		ahc_aic7770_VL_setup
77 	},
78 	{
79 		ID_AHA_284x,
80 		0xFFFFFFFE,
81 		"Adaptec 284X SCSI adapter (BIOS Disabled)",
82 		ahc_aic7770_VL_setup
83 	},
84 	{
85 		ID_OLV_274x,
86 		0xFFFFFFFF,
87 		"Adaptec (Olivetti OEM) 274X SCSI adapter",
88 		ahc_aic7770_EISA_setup
89 	},
90 	{
91 		ID_OLV_274xD,
92 		0xFFFFFFFF,
93 		"Adaptec (Olivetti OEM) 274X Differential SCSI adapter",
94 		ahc_aic7770_EISA_setup
95 	},
96 	/* Generic chip probes for devices we don't know 'exactly' */
97 	{
98 		ID_AIC7770,
99 		0xFFFFFFFF,
100 		"Adaptec aic7770 SCSI adapter",
101 		ahc_aic7770_EISA_setup
102 	}
103 };
104 const int ahc_num_aic7770_devs = NUM_ELEMENTS(aic7770_ident_table);
105 
106 struct aic7770_identity *
aic7770_find_device(uint32_t id)107 aic7770_find_device(uint32_t id)
108 {
109 	struct	aic7770_identity *entry;
110 	int	i;
111 
112 	for (i = 0; i < ahc_num_aic7770_devs; i++) {
113 		entry = &aic7770_ident_table[i];
114 		if (entry->full_id == (id & entry->id_mask))
115 			return (entry);
116 	}
117 	return (NULL);
118 }
119 
120 int
aic7770_config(struct ahc_softc * ahc,struct aic7770_identity * entry,u_int io)121 aic7770_config(struct ahc_softc *ahc, struct aic7770_identity *entry, u_int io)
122 {
123 	int	error;
124 	int	have_seeprom;
125 	u_int	hostconf;
126 	u_int   irq;
127 	u_int	intdef;
128 
129 	error = entry->setup(ahc);
130 	have_seeprom = 0;
131 	if (error != 0)
132 		return (error);
133 
134 	error = aic7770_map_registers(ahc, io);
135 	if (error != 0)
136 		return (error);
137 
138 	/*
139 	 * Before we continue probing the card, ensure that
140 	 * its interrupts are *disabled*.  We don't want
141 	 * a misstep to hang the machine in an interrupt
142 	 * storm.
143 	 */
144 	ahc_intr_enable(ahc, FALSE);
145 
146 	ahc->description = entry->name;
147 	error = ahc_softc_init(ahc);
148 	if (error != 0)
149 		return (error);
150 
151 	ahc->bus_chip_init = aic7770_chip_init;
152 	ahc->bus_suspend = aic7770_suspend;
153 	ahc->bus_resume = aic7770_resume;
154 
155 	error = ahc_reset(ahc, /*reinit*/FALSE);
156 	if (error != 0)
157 		return (error);
158 
159 	/* Make sure we have a valid interrupt vector */
160 	intdef = ahc_inb(ahc, INTDEF);
161 	irq = intdef & VECTOR;
162 	switch (irq) {
163 	case 9:
164 	case 10:
165 	case 11:
166 	case 12:
167 	case 14:
168 	case 15:
169 		break;
170 	default:
171 		printf("aic7770_config: invalid irq setting %d\n", intdef);
172 		return (ENXIO);
173 	}
174 
175 	if ((intdef & EDGE_TRIG) != 0)
176 		ahc->flags |= AHC_EDGE_INTERRUPT;
177 
178 	switch (ahc->chip & (AHC_EISA|AHC_VL)) {
179 	case AHC_EISA:
180 	{
181 		u_int biosctrl;
182 		u_int scsiconf;
183 		u_int scsiconf1;
184 
185 		biosctrl = ahc_inb(ahc, HA_274_BIOSCTRL);
186 		scsiconf = ahc_inb(ahc, SCSICONF);
187 		scsiconf1 = ahc_inb(ahc, SCSICONF + 1);
188 
189 		/* Get the primary channel information */
190 		if ((biosctrl & CHANNEL_B_PRIMARY) != 0)
191 			ahc->flags |= 1;
192 
193 		if ((biosctrl & BIOSMODE) == BIOSDISABLED) {
194 			ahc->flags |= AHC_USEDEFAULTS;
195 		} else {
196 			if ((ahc->features & AHC_WIDE) != 0) {
197 				ahc->our_id = scsiconf1 & HWSCSIID;
198 				if (scsiconf & TERM_ENB)
199 					ahc->flags |= AHC_TERM_ENB_A;
200 			} else {
201 				ahc->our_id = scsiconf & HSCSIID;
202 				ahc->our_id_b = scsiconf1 & HSCSIID;
203 				if (scsiconf & TERM_ENB)
204 					ahc->flags |= AHC_TERM_ENB_A;
205 				if (scsiconf1 & TERM_ENB)
206 					ahc->flags |= AHC_TERM_ENB_B;
207 			}
208 		}
209 		if ((ahc_inb(ahc, HA_274_BIOSGLOBAL) & HA_274_EXTENDED_TRANS))
210 			ahc->flags |= AHC_EXTENDED_TRANS_A|AHC_EXTENDED_TRANS_B;
211 		break;
212 	}
213 	case AHC_VL:
214 	{
215 		have_seeprom = aha2840_load_seeprom(ahc);
216 		break;
217 	}
218 	default:
219 		break;
220 	}
221 	if (have_seeprom == 0) {
222 		free(ahc->seep_config, M_DEVBUF);
223 		ahc->seep_config = NULL;
224 	}
225 
226 	/*
227 	 * Ensure autoflush is enabled
228 	 */
229 	ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) & ~AUTOFLUSHDIS);
230 
231 	/* Setup the FIFO threshold and the bus off time */
232 	hostconf = ahc_inb(ahc, HOSTCONF);
233 	ahc_outb(ahc, BUSSPD, hostconf & DFTHRSH);
234 	ahc_outb(ahc, BUSTIME, (hostconf << 2) & BOFF);
235 
236 	ahc->bus_softc.aic7770_softc.busspd = hostconf & DFTHRSH;
237 	ahc->bus_softc.aic7770_softc.bustime = (hostconf << 2) & BOFF;
238 
239 	/*
240 	 * Generic aic7xxx initialization.
241 	 */
242 	error = ahc_init(ahc);
243 	if (error != 0)
244 		return (error);
245 
246 	error = aic7770_map_int(ahc, irq);
247 	if (error != 0)
248 		return (error);
249 
250 	ahc_lock(ahc);
251 	/*
252 	 * Link this softc in with all other ahc instances.
253 	 */
254 	ahc_softc_insert(ahc);
255 
256 	/*
257 	 * Enable the board's BUS drivers
258 	 */
259 	ahc_outb(ahc, BCTL, ENABLE);
260 
261 	ahc_unlock(ahc);
262 
263 	return (0);
264 }
265 
266 static int
aic7770_chip_init(struct ahc_softc * ahc)267 aic7770_chip_init(struct ahc_softc *ahc)
268 {
269 	ahc_outb(ahc, BUSSPD, ahc->bus_softc.aic7770_softc.busspd);
270 	ahc_outb(ahc, BUSTIME, ahc->bus_softc.aic7770_softc.bustime);
271 	ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) & ~AUTOFLUSHDIS);
272 	ahc_outb(ahc, BCTL, ENABLE);
273 	return (ahc_chip_init(ahc));
274 }
275 
276 static int
aic7770_suspend(struct ahc_softc * ahc)277 aic7770_suspend(struct ahc_softc *ahc)
278 {
279 	return (ahc_suspend(ahc));
280 }
281 
282 static int
aic7770_resume(struct ahc_softc * ahc)283 aic7770_resume(struct ahc_softc *ahc)
284 {
285 	return (ahc_resume(ahc));
286 }
287 
288 /*
289  * Read the 284x SEEPROM.
290  */
291 static int
aha2840_load_seeprom(struct ahc_softc * ahc)292 aha2840_load_seeprom(struct ahc_softc *ahc)
293 {
294 	struct	seeprom_descriptor sd;
295 	struct	seeprom_config *sc;
296 	int	have_seeprom;
297 	uint8_t scsi_conf;
298 
299 	sd.sd_ahc = ahc;
300 	sd.sd_control_offset = SEECTL_2840;
301 	sd.sd_status_offset = STATUS_2840;
302 	sd.sd_dataout_offset = STATUS_2840;
303 	sd.sd_chip = C46;
304 	sd.sd_MS = 0;
305 	sd.sd_RDY = EEPROM_TF;
306 	sd.sd_CS = CS_2840;
307 	sd.sd_CK = CK_2840;
308 	sd.sd_DO = DO_2840;
309 	sd.sd_DI = DI_2840;
310 	sc = ahc->seep_config;
311 
312 	if (bootverbose)
313 		printf("%s: Reading SEEPROM...", ahc_name(ahc));
314 	have_seeprom = ahc_read_seeprom(&sd, (uint16_t *)sc,
315 					/*start_addr*/0, sizeof(*sc)/2);
316 
317 	if (have_seeprom) {
318 		if (ahc_verify_cksum(sc) == 0) {
319 			if(bootverbose)
320 				printf ("checksum error\n");
321 			have_seeprom = 0;
322 		} else if (bootverbose) {
323 			printf("done.\n");
324 		}
325 	}
326 
327 	if (!have_seeprom) {
328 		if (bootverbose)
329 			printf("%s: No SEEPROM available\n", ahc_name(ahc));
330 		ahc->flags |= AHC_USEDEFAULTS;
331 	} else {
332 		/*
333 		 * Put the data we've collected down into SRAM
334 		 * where ahc_init will find it.
335 		 */
336 		int	 i;
337 		int	 max_targ;
338 		uint16_t discenable;
339 
340 		max_targ = (ahc->features & AHC_WIDE) != 0 ? 16 : 8;
341 		discenable = 0;
342 		for (i = 0; i < max_targ; i++){
343 			uint8_t target_settings;
344 
345 			target_settings = (sc->device_flags[i] & CFXFER) << 4;
346 			if (sc->device_flags[i] & CFSYNCH)
347 				target_settings |= SOFS;
348 			if (sc->device_flags[i] & CFWIDEB)
349 				target_settings |= WIDEXFER;
350 			if (sc->device_flags[i] & CFDISC)
351 				discenable |= (0x01 << i);
352 			ahc_outb(ahc, TARG_SCSIRATE + i, target_settings);
353 		}
354 		ahc_outb(ahc, DISC_DSB, ~(discenable & 0xff));
355 		ahc_outb(ahc, DISC_DSB + 1, ~((discenable >> 8) & 0xff));
356 
357 		ahc->our_id = sc->brtime_id & CFSCSIID;
358 
359 		scsi_conf = (ahc->our_id & 0x7);
360 		if (sc->adapter_control & CFSPARITY)
361 			scsi_conf |= ENSPCHK;
362 		if (sc->adapter_control & CFRESETB)
363 			scsi_conf |= RESET_SCSI;
364 
365 		if (sc->bios_control & CF284XEXTEND)
366 			ahc->flags |= AHC_EXTENDED_TRANS_A;
367 		/* Set SCSICONF info */
368 		ahc_outb(ahc, SCSICONF, scsi_conf);
369 
370 		if (sc->adapter_control & CF284XSTERM)
371 			ahc->flags |= AHC_TERM_ENB_A;
372 	}
373 	return (have_seeprom);
374 }
375 
376 static int
ahc_aic7770_VL_setup(struct ahc_softc * ahc)377 ahc_aic7770_VL_setup(struct ahc_softc *ahc)
378 {
379 	int error;
380 
381 	error = ahc_aic7770_setup(ahc);
382 	ahc->chip |= AHC_VL;
383 	return (error);
384 }
385 
386 static int
ahc_aic7770_EISA_setup(struct ahc_softc * ahc)387 ahc_aic7770_EISA_setup(struct ahc_softc *ahc)
388 {
389 	int error;
390 
391 	error = ahc_aic7770_setup(ahc);
392 	ahc->chip |= AHC_EISA;
393 	return (error);
394 }
395 
396 static int
ahc_aic7770_setup(struct ahc_softc * ahc)397 ahc_aic7770_setup(struct ahc_softc *ahc)
398 {
399 	ahc->channel = 'A';
400 	ahc->channel_b = 'B';
401 	ahc->chip = AHC_AIC7770;
402 	ahc->features = AHC_AIC7770_FE;
403 	ahc->bugs |= AHC_TMODE_WIDEODD_BUG;
404 	ahc->flags |= AHC_PAGESCBS;
405 	ahc->instruction_ram_size = 448;
406 	return (0);
407 }
408