| /freebsd/sys/contrib/device-tree/Bindings/pinctrl/ |
| H A D | pinctrl-single.txt | 69 - pinctrl-single,low-power-mode : array of value that are used to configure
70 low power mode of this pin. For some silicons, the low power mode will
71 control the output of the pin when the pad including the pin enter low
73 /* low power mode value, mask */
74 pinctrl-single,low-power-mode = <0x288 0x388>;
|
| H A D | pinctrl-stmfx.txt | 30 - drive-push-pull: the pin will be driven actively high and low.
32 - output-low: the pin will be configured as an output driving low level.
|
| /freebsd/contrib/lua/src/ |
| H A D | lmathlib.c | 558 lua_Integer low, up; in math_random() local
568 low = 1; in math_random()
577 low = luaL_checkinteger(L, 1); in math_random()
584 luaL_argcheck(L, low <= up, 1, "interval is empty"); in math_random()
586 p = project(I2UInt(rv), (lua_Unsigned)up - (lua_Unsigned)low, state); in math_random()
587 lua_pushinteger(L, p + (lua_Unsigned)low); in math_random()
|
| /freebsd/sys/contrib/device-tree/Bindings/net/ |
| H A D | rockchip-dwmac.txt | 37 - snps,reset-active-low boolean flag to indicate if phy reset is active low.
69 snps,reset-active-low;
|
| H A D | renesas,ether.yaml | 77 renesas,ether-link-active-low:
80 specify when the Ether LINK signal is active-low instead of normal
116 renesas,ether-link-active-low;
|
| H A D | mediatek-bluetooth.txt | 58 - pinctrl-0: Should contain UART RXD low when the device is powered up to
73 - reset-gpios: GPIO used to reset the device whose initial state keeps low,
87 output-low;
|
| /freebsd/sys/contrib/device-tree/Bindings/gpio/ |
| H A D | gpio-mvebu.txt | 37 1 = low-to-high edge triggered.
38 2 = high-to-low edge triggered.
40 8 = active low level-sensitive.
|
| H A D | aspeed,sgpio.yaml | 18 sensitivity option (level-high, level-low, edge-high, edge-low)
|
| /freebsd/sys/contrib/device-tree/Bindings/interrupt-controller/ |
| H A D | open-pic.txt | 45 0 = low-to-high edge triggered
46 1 = active low level-sensitive
48 3 = high-to-low edge triggered
|
| H A D | snps,dw-apb-ictl.txt | 20 - 0 maps to bit 0 of low interrupts,
21 - 1 maps to bit 1 of low interrupts,
|
| /freebsd/sys/contrib/device-tree/Bindings/regulator/ |
| H A D | tps62360-regulator.txt | 21 If this property is missing, then assume the state as low (0).
23 If this property is missing, then assume the state as low (0).
|
| /freebsd/sys/contrib/device-tree/Bindings/iio/adc/ |
| H A D | adi,ad7768-1.txt | 18 if the filter decimation rate changes. As the line is active low, it should
24 driver probe. As the line is active low, it should be marked GPIO_ACTIVE_LOW.
|
| /freebsd/sys/contrib/device-tree/Bindings/media/i2c/ |
| H A D | ovti,ov5670.yaml | 29 description: Reference to the GPIO connected to the PWDNB pin. Active low.
32 description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low.
|
| /freebsd/sys/contrib/device-tree/src/arm/renesas/ |
| H A D | r8a7742-iwg21m.dtsi | 39 /* GP0_18 set low to select QSPI. Doing so will disable VIN2 */
43 output-low;
|
| /freebsd/sys/contrib/device-tree/src/arm64/renesas/ |
| H A D | rzg2ul-smarc-pinfunction.dtsi | 24 output-low;
38 output-low;
|
| /freebsd/sys/dev/isci/scil/ |
| H A D | scic_sds_port_configuration_agent.c | 113 else if (address_one.low > address_two.low) in sci_sas_address_compare()
117 else if (address_one.low < address_two.low) in sci_sas_address_compare()
332 sas_address.low = 0; in scic_sds_mpc_agent_validate_phy_configuration()
|
| /freebsd/usr.sbin/ppp/ |
| H A D | nat_cmd.c | 345 StrToPortRange(const char *str, u_short *low, u_short *high, const char *proto) in StrToPortRange() argument
354 res = StrToPort(str, low, proto); in StrToPortRange()
363 *high = *low; in StrToPortRange()
370 StrToAddrAndPort(const char *str, struct in_addr *addr, u_short *low, in StrToAddrAndPort() argument
388 return StrToPortRange(colon + 1, low, high, proto); in StrToAddrAndPort()
|
| /freebsd/contrib/one-true-awk/ |
| H A D | lex.c | 501 int cond, low, mid, high; in binsearch() local
503 low = 0; in binsearch()
505 while (low <= high) { in binsearch()
506 mid = (low + high) / 2; in binsearch()
510 low = mid + 1; in binsearch()
|
| /freebsd/sys/contrib/device-tree/src/arm64/qcom/ |
| H A D | sc7280-qcard.dtsi | 509 * maintain a low power state regardless of whether
578 output-low;
586 output-low;
596 output-low;
606 * maintain a low power state regardless of whether
618 * Configure pull-down on RTS. As RTS is active low
619 * signal, pull it low to indicate the BT SoC that it
621 * pulling RX low (by sending wakeup bytes).
|
| /freebsd/sys/contrib/device-tree/Bindings/soc/ti/ |
| H A D | wkup-m3-ipc.yaml | 15 (commonly referred to as Wakeup M3 or CM3) to help with various low power tasks
40 override the pin's existing bias (pull-up/pull-down) and value (high/low) when
47 during low power mode entry.
90 into a low power state.
|
| /freebsd/sys/contrib/device-tree/src/arm/marvell/ |
| H A D | dove-sbc-a510.dts | 51 * 0.3 DVI transmitter TI TFP410 PD# (active low power down)
52 * 0.4 LVDS transmitter DS90C365 PD# (active low power down)
53 * 0.5 LCD nRST (active low reset)
54 * 0.6 PCIe0 nRST (active low reset)
|
| /freebsd/sys/contrib/device-tree/Bindings/sound/ |
| H A D | qcom,msm8916-wcd-analog.txt | 35 - qcom,mbhc-vthreshold-low: Array of 5 threshold voltages in mV for 5 buttons
37 by internal current source, this is a low power.
65 qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
|
| /freebsd/sys/contrib/device-tree/src/arm64/freescale/ |
| H A D | imx8mm-var-som-symphony.dts | 94 output-low;
101 output-low;
108 output-low;
|
| H A D | imx8mn-var-som-symphony.dts | 97 output-low;
104 output-low;
111 output-low;
|
| /freebsd/sys/contrib/device-tree/Bindings/fpga/ |
| H A D | lattice,sysconfig.yaml | 30 A GPIO line connected to PROGRAMN (active low) pin of the device.
36 A GPIO line connected to INITN (active low) pin of the device.
|