Searched refs:set (Results 3001 – 3025 of 5983) sorted by relevance
1...<<121122123124125126127128129130>>...240
/freebsd/sys/contrib/device-tree/Bindings/sound/ |
H A D | imx-audio-spdif.txt | 25 * Note: At least one of these two properties should be set in the DT binding.
|
H A D | wm8962.txt | 16 of R51 (Class D Control 2) gets set, indicating that the speaker is
|
/freebsd/contrib/tcsh/nls/greek/ |
H A D | set3 | 2 $set 3
|
/freebsd/sys/contrib/device-tree/Bindings/crypto/ |
H A D | omap-des.txt | 7 - reg : Offset and length of the register set for the module
|
/freebsd/sys/contrib/device-tree/Bindings/gpio/ |
H A D | gpio-grgpio.txt | 12 - reg : Address and length of the register set for the device
|
/freebsd/contrib/sendmail/cf/feature/ |
H A D | compat_check.m4 | 6 # By using this file, you agree to the terms and conditions set
|
H A D | nullclient.m4 | 9 # By using this file, you agree to the terms and conditions set
|
/freebsd/sys/contrib/device-tree/Bindings/media/ |
H A D | imx7-csi.txt | 13 - reg : base address and length of the register set for the device;
|
/freebsd/sys/contrib/device-tree/Bindings/mfd/ |
H A D | zii,rave-sp.txt | 16 - current-speed: Should be set to baud rate SP device is using
|
/freebsd/sys/contrib/device-tree/Bindings/arm/ |
H A D | ste-u300.txt | 26 syscon registers to set the board as self-powered.
|
/freebsd/sys/contrib/device-tree/Bindings/iio/proximity/ |
H A D | as3935.txt | 19 startup. This will need to set according to the noise from the
|
/freebsd/sys/contrib/device-tree/Bindings/leds/backlight/ |
H A D | kinetic,ktd253.yaml | 15 it goes to maximum backlight then you can set the level of backlight
|
/freebsd/sys/contrib/device-tree/Bindings/phy/ |
H A D | qcom-pcie2-phy.txt | 11 - reg: offset and length of the PHY register set.
|
/freebsd/contrib/llvm-project/compiler-rt/lib/builtins/hexagon/ |
H A D | divsi3.S | 83 .set __qdsp_divsi3, __hexagon_divsi3
|
/freebsd/contrib/sendmail/cf/domain/ |
H A D | generic.m4 | 9 # By using this file, you agree to the terms and conditions set
|
/freebsd/sys/contrib/device-tree/Bindings/serial/ |
H A D | sirf-uart.txt | 6 - reg : Offset and length of the register set for the device
|
/freebsd/contrib/llvm-project/llvm/lib/Target/Mips/ |
H A D | MipsMulMulBugPass.cpp | 46 return MachineFunctionProperties().set( in getRequiredProperties()
|
/freebsd/sys/contrib/device-tree/Bindings/pinctrl/ |
H A D | mscc,ocelot-pinctrl.txt | 9 - reg : Address and length of the register set for the device
|
/freebsd/sys/contrib/device-tree/Bindings/regulator/ |
H A D | rohm,bd9576-regulator.yaml | 34 to be set.
|
/freebsd/usr.bin/ministat/ |
H A D | README | 10 You need at least three data points in each data set, but the more
|
/freebsd/sys/contrib/device-tree/Bindings/iio/temperature/ |
H A D | melexis,mlx90614.yaml | 28 device. In normal operation, the GPIO is set as input and will
|
/freebsd/sys/contrib/device-tree/src/arm/intel/ixp/ |
H A D | intel-ixp43x-kixrp435.dts | 37 /* CHECKME: ethernet set-up taken from Gateworks Cambria */
|
/freebsd/contrib/llvm-project/llvm/include/llvm/ExecutionEngine/Orc/ |
H A D | CompileOnDemandLayer.h | 63 using GlobalValueSet = std::set<const GlobalValue *>;
|
/freebsd/contrib/llvm-project/llvm/lib/TextAPI/ |
H A D | Target.cpp | 72 Result.set(Target.Arch); in mapToArchitectureSet()
|
/freebsd/sys/contrib/device-tree/Bindings/mtd/partitions/ |
H A D | u-boot.yaml | 13 Device configuration is stored as a set of environment variables that are
|
1...<<121122123124125126127128129130>>...240