| /freebsd/sys/contrib/device-tree/Bindings/sound/ |
| H A D | adi,adau1701.txt | 7 and ADDR1, as wired in hardware.
|
| H A D | tas571x.txt | 4 signals that can be wired up to GPIOs: reset (strongly recommended), and
|
| H A D | adi,adau1977.txt | 38 and ADDR1, as wired in hardware.
|
| /freebsd/tools/tools/net80211/scripts/ |
| H A D | config | 35 test -z "$WIRED" && { echo "No wired device detected!"; exit; }
|
| /freebsd/sys/contrib/device-tree/Bindings/net/ |
| H A D | wiznet,w5x00.txt | 13 - reg: Specify the SPI chip select the chip is wired to.
|
| H A D | microchip,lan95xx.yaml | 13 Device tree properties for hard wired SMSC95xx compatible USB Ethernet
|
| H A D | microchip,enc28j60.txt | 10 - reg: Specify the SPI chip select the ENC28J60 is wired to
|
| H A D | smsc911x.txt | 27 of the device. On many systems this is wired high so the device goes
|
| /freebsd/sys/contrib/device-tree/Bindings/net/dsa/ |
| H A D | ksz.txt | 31 Ethernet switch connected via SPI to the host, CPU port wired to eth0:
|
| /freebsd/sys/contrib/device-tree/Bindings/display/bridge/ |
| H A D | tda998x.txt | 22 output is wired to the TDA998x input - default: <0x230145>
|
| H A D | nxp,tda998x.yaml | 27 24 bits value which defines how the video controller output is wired to
|
| /freebsd/sys/contrib/device-tree/src/arm/synaptics/ |
| H A D | berlin2cd-valve-steamlink.dts | 71 * port wired to the on-board Steam Controller wireless receiver chip. */
|
| /freebsd/sys/contrib/device-tree/Bindings/bus/ |
| H A D | ti-sysc.yaml | 117 Target module reset bit in the RSTCTRL register if wired for the module.
125 "rstctrl" if only one reset bit is wired for the module.
|
| /freebsd/sys/contrib/device-tree/Bindings/mfd/ |
| H A D | twl4030-power.txt | 23 depending on how the external oscillator is wired.
|
| /freebsd/sys/contrib/device-tree/Bindings/media/i2c/ |
| H A D | sony,imx214.txt | 12 - reg: I2C bus address of the device. Depending on how the sensor is wired,
|
| /freebsd/sys/contrib/device-tree/src/arm64/allwinner/ |
| H A D | sun50i-h618-orangepi-zero3.dts | 27 * The schematic shows the card detect pin wired up to PF6, via an
|
| /freebsd/sys/contrib/device-tree/Bindings/iio/adc/ |
| H A D | adi,ad7280a.yaml | 35 alerts, typically because not all are wired to anything. Only applies to
|
| /freebsd/sys/contrib/device-tree/Bindings/interrupt-controller/ |
| H A D | arm,vic.txt | 23 at source 31 at MSb. A bit that is set means that the source is wired and
|
| H A D | hisilicon,mbigen-v2.txt | 8 To reduce the wired interrupt number connected to GIC,
|
| H A D | brcm,bcm6345-l1-intc.txt | 10 - Most onchip peripherals are wired directly to an L1 input
|
| H A D | arm,vic.yaml | 47 that the source is wired and clear means otherwise. If unspecified,
|
| /freebsd/sys/contrib/device-tree/src/arm/marvell/ |
| H A D | kirkwood-nas2big.dts | 46 * wired to a separate GPIO.
|
| /freebsd/sys/contrib/device-tree/Bindings/gpio/ |
| H A D | gpio-max3191x.txt | 21 (if all chips are wired to the same pin).
|
| /freebsd/sys/contrib/device-tree/Bindings/i2c/ |
| H A D | i2c-s3c2410.txt | 23 lines are permanently wired to the respective clienta
|
| /freebsd/sys/contrib/device-tree/Bindings/leds/ |
| H A D | leds-pm8058.txt | 8 are more of a suggestion than a hard-wired usecase.
|