Home
last modified time | relevance | path

Searched refs:IP (Results 1 – 21 of 21) sorted by relevance

/qemu/qapi/
H A Drocker.json135 # @ip-proto: IP Header protocol field
137 # @ip-tos: IP header TOS field
139 # @ip-dst: IP header destination address
167 # @ip-proto: IP Header protocol field
169 # @ip-tos: IP header TOS field
H A Dnet.json131 # @net: IP network address that the guest will see, in the form
167 # @smbserver: IP address of the built-in SMB server
538 # Must be in the private IP range (RFC 1918). Must be specified
544 # interface. Must be in the private IP range (RFC 1918). Must be
585 # Must be in the private IP range (RFC 1918). Must be specified
591 # interface. Must be in the private IP range (RFC 1918). Must be
H A Dui.json211 # @host: IP address
296 # the name resolution on the host and may be an IP address.
474 # @host: IP address
534 # name resolution on the host and may be an IP address.
/qemu/docs/specs/
H A Dsev-guest-firmware.rst94 * IP value [0:15]
97 A hypervisor reads the CS segment base and IP value. The CS segment
101 would then program the EIP register with the IP value as read.
H A Drocker.txt580 1: insert IP csum (ipv4 only)
595 length of ethernet, IP, and
596 TCP/UDP headers, including IP
636 (1 << 4): IP fragment
641 RX_CSUM 2 IP calculated checksum:
642 IPv4: IP payload csum
785 OF_DPA_SRC_IP_MASK 4 (N) IP Mask
841 OF_DPA_SRC_IP_MASK 4 (N) IP Mask
844 OF_DPA_DST_IP_MASK 4 (N) IP Mask
856 OF_DPA_SRC_ARP_IP_MASK 4 (N) IP Mask
[all …]
H A Dfsi.rst39 integration of the FSI master IP with the OPB, mainly the existence of an
/qemu/hw/ipack/
H A Dtpci200.c38 #define STATUS_INT(IP, INTNO) BIT((IP) * 2 + (INTNO)) argument
39 #define STATUS_TIME(IP) BIT((IP) + 12) argument
/qemu/tests/rocker/
H A Dport13 # config IP on hosts
H A Dbridge34 # config IP on hosts
H A Dbridge-stp28 # config IP on hosts
H A Dbridge-vlan40 # config IP on host VLANs
H A Dbridge-vlan-stp35 # config IP on host VLANs
/qemu/docs/system/
H A Dtls.rst88 certificate are the hostnames and/or IP addresses that will be used by
89 clients when connecting. The hostname / IP address that the client
91 IP address(es) recorded in the server certificate, and if no match is
96 permanently assigned IP address(es), and clients are likely to use them
/qemu/docs/
H A DCOLO-FT.txt149 change the IP Addresses if you want to run it on two hosts. Initially
155 You don't need to change any IP's here, because 0.0.0.0 listens on any
156 interface. The chardev's with 127.0.0.1 IP's loopback to the local qemu
183 any IP's here, except for the $primary_ip variable.
H A Dcolo-proxy.txt161 Here is an example using demonstration IP and port addresses to more
H A Dblock-replication.txt172 2. host is the secondary physical machine's hostname or IP
H A Drdma.txt29 of the significantly lower latency and higher throughput over TCP/IP. This is
/qemu/docs/system/devices/
H A Dcanokey.rst21 * (virt-card) CanoKey USB/IP
/qemu/qga/
H A Dqapi-schema.json644 # An enumeration of supported IP address types
646 # @ipv4: IP version 4
648 # @ipv6: IP version 6
658 # @ip-address: IP address
726 # Get list of guest IP addresses, MAC addresses and netmasks.
/qemu/docs/about/
H A Dremoved-features.rst890 processor IP (see `Intel discontinuance notification`_).
1004 processor IP (see `Intel discontinuance notification`_).
/qemu/
H A Dqemu-options.hx2297 Set the IP address spice is listening on. Default is any
2301 Force using the specified IP version.
3058 Set IP network address the guest will see. Optionally specify
3064 2nd IP in the guest network, i.e. x.x.x.2.
3078 will not be able to contact the host and no guest IP packets
3088 assign. Default is the 15th to 31st IP in the guest network,
3094 3rd IP in the guest network, i.e. x.x.x.3.
3099 Default is the 3rd IP in the guest network, i.e. xxxx::3.
3148 ``dir`` transparently. The IP address of the SMB server can be
3168 hostport to the guest IP address guestaddr on guest port
[all …]