| /freebsd/sys/contrib/device-tree/src/arm/microchip/ |
| H A D | at91-natte.dtsi | 71 ti,charge-current = <2000>;
72 ti,charge-voltage = <16800>;
87 ti,charge-current = <2000>;
88 ti,charge-voltage = <16800>;
103 ti,charge-current = <2000>;
104 ti,charge-voltage = <16800>;
119 ti,charge-current = <2000>;
135 ti,charge-current = <2000>;
151 ti,charge-current = <2000>;
167 ti,charge-current = <2000>;
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/power/supply/ |
| H A D | gpio-charger.yaml | 38 charge-status-gpios:
42 charge-current-limit-gpios:
47 charge-current-limit-mapping:
58 charge-current-limit-gpios property. Bit 1 second to last
68 - charge-status-gpios
70 - charge-current-limit-gpios
73 charge-current-limit-gpios: [ charge-current-limit-mapping ]
74 charge-current-limit-mapping: [ charge-current-limit-gpios ]
87 charge-status-gpios = <&gpc 27 GPIO_ACTIVE_LOW>;
89 charge-current-limit-gpios = <&gpioA 11 GPIO_ACTIVE_HIGH>,
[all …]
|
| H A D | richtek,rt5033-charger.yaml | 27 Current of pre-charge mode. The pre-charge current levels are 350 mA
30 constant-charge-current-max-microamp:
31 Current of fast-charge mode. The fast-charge current levels are 700 mA
34 charge-term-current-microamp:
35 This property is end of charge current. Its level ranges from 150 mA
40 Voltage of pre-charge mode. If the battery voltage is below the pre-charge
41 threshold voltage, the charger is in pre-charge mode with pre-charge
44 constant-charge-voltage-max-microvolt:
|
| H A D | qcom,pm8941-charger.yaml | 23 - description: charge done
24 - description: charge fast mode
25 - description: charge trickle mode
43 qcom,fast-charge-current-limit:
49 qcom,fast-charge-low-threshold-voltage:
57 qcom,fast-charge-high-threshold-voltage:
66 qcom,fast-charge-safe-voltage:
75 qcom,fast-charge-safe-current:
120 usb-charge-current-limit:
125 Default USB charge current limit in uA.
[all …]
|
| H A D | qcom_smbb.txt | 21 - charge done
22 - charge fast mode
23 - charge trickle mode
43 - qcom,fast-charge-current-limit:
48 - qcom,fast-charge-low-threshold-voltage:
55 - qcom,fast-charge-high-threshold-voltage:
62 - qcom,fast-charge-safe-voltage:
69 - qcom,fast-charge-safe-current:
91 Description: Default DC charge current limit
145 qcom,fast-charge-current-limit = <1000000>;
[all …]
|
| H A D | richtek,rt9455.yaml | 25 richtek,output-charge-current:
29 richtek,end-of-charge-percentage:
32 percent of the output charge current. When the current in constant-voltage phase drops
33 below output_charge_current x end-of-charge-percentage, charge is terminated.
61 - richtek,output-charge-current
62 - richtek,end-of-charge-percentage
82 richtek,output-charge-current = <500000>;
83 richtek,end-of-charge-percentage = <10>;
|
| H A D | rohm,bd99954.yaml | 33 # a) Trickle-charge with constant current (8).
34 # b) pre-charge with constant current (6)
35 # c) fast-charge with:
70 # - trickle-charge-current-microamp:
71 # Current used at trickle-charge phase (8 in above chart)
76 # Current used at pre-charge phase (6 in above chart)
80 # - constant-charge-current-max-microamp
85 # - constant-charge-voltage-max-microvolt
96 # - re-charge-voltage-microvolt
108 # - charge-term-current-microamp
[all …]
|
| H A D | battery.yaml | 51 re-charge-voltage-microvolt:
63 charge-full-design-microamp-hours:
66 trickle-charge-current-microamp:
67 description: current for trickle-charge phase
70 description: current for pre-charge phase
75 charge-term-current-microamp:
76 description: current for charge termination phase
78 constant-charge-current-max-microamp:
81 constant-charge-voltage-max-microvolt:
151 re-charge-voltage-microvolt = <250000>;
[all …]
|
| H A D | rt9455_charger.txt | 9 - richtek,output-charge-current: integer, output current from the charger to the
11 - richtek,end-of-charge-percentage: integer, percent of the output charge current.
13 below output_charge_current x end-of-charge-percentage,
14 charge is terminated.
39 richtek,output-charge-current = <500000>;
40 richtek,end-of-charge-percentage = <10>;
|
| H A D | sc2731_charger.txt | 11 - charge-term-current-microamp: current for charge termination phase.
12 - constant-charge-voltage-max-microvolt: maximum constant input voltage.
19 charge-term-current-microamp = <120000>;
20 constant-charge-voltage-max-microvolt = <4350000>;
|
| H A D | sc2731-charger.yaml | 29 - charge-term-current-microamp: current for charge termination phase.
30 - constant-charge-voltage-max-microvolt: maximum constant input voltage.
38 charge-term-current-microamp = <120000>;
39 constant-charge-voltage-max-microvolt = <4350000>;
|
| H A D | sc27xx-fg.txt | 12 - io-channels: Specify the IIO ADC channels to get temperature and charge voltage.
13 - io-channel-names: Should be "bat-temp" or "charge-vol".
25 charge-full-design-microamp-hours = <1900000>;
26 constant-charge-voltage-max-microvolt = <4350000>;
53 io-channel-names = "bat-temp", "charge-vol";
|
| H A D | bq24190.txt | 15 + precharge-current-microamp: maximum charge current during precharge
17 + charge-term-current-microamp: a charge cycle terminates when the
32 charge current on USB SDP ports, among other features). To simulate this on
40 charge-term-current-microamp = <128000>;
|
| H A D | summit,smb347-charger.yaml | 42 summit,enable-charge-control:
51 description: Voltage threshold to transit to fast charge mode (in uV)
61 summit,charge-current-compensation-microamp:
114 summit,charge-current-compensation-microamp:
127 summit,charge-current-compensation-microamp:
156 summit,enable-charge-control = <SMB3XX_CHG_ENABLE_PIN_ACTIVE_HIGH>;
179 constant-charge-current-max-microamp = <1800000>;
|
| H A D | cpcap-charger.yaml | 29 - description: reverse charge interrupt
33 - description: charge current 2 interrupt
34 - description: charge current 1 interrupt
55 - description: battery charge current
69 charge controller that is controlled with two GPIOs
|
| H A D | bq2515x.yaml | 14 The BQ2515x family is a highly integrated battery charge management IC that
47 charge-enable-gpios:
71 constant-charge-current-max-microamp = <50000>;
73 constant-charge-voltage-max-microvolt = <4000000>;
89 charge-enable-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
| H A D | bq25890.yaml | 38 ti,charge-current:
45 charge will be terminated when current in constant-voltage phase
50 description: maximum charge current during precharge phase (in uA)
79 temperature above which the charge current is lowered, to avoid overheating
93 - ti,charge-current
117 ti,charge-current = <1000000>;
|
| H A D | bq25890.txt | 15 - ti,charge-current: integer, maximum charging current (in uA);
16 - ti,termination-current: integer, charge will be terminated when current in
18 - ti,precharge-current: integer, maximum charge current during precharge
33 - ti,thermal-regulation-threshold: integer, temperature above which the charge
51 ti,charge-current = <1000000>;
|
| H A D | maxim,max14577.yaml | 39 maxim,fast-charge-uamp:
57 - maxim,fast-charge-uamp
71 maxim,fast-charge-uamp:
80 maxim,fast-charge-uamp:
|
| H A D | sc27xx-fg.yaml | 38 - const: charge-vol
70 charge-full-design-microamp-hours = <1900000>;
71 constant-charge-voltage-max-microvolt = <4350000>;
92 io-channel-names = "bat-temp", "charge-vol";
|
| H A D | richtek,rt9467.yaml | 17 regulation, and charge termination. The charge current is regulated through
38 charge-enable-gpios:
72 charge-enable-gpios = <&gpio26 1 GPIO_ACTIVE_LOW>;
|
| H A D | bq2415x.yaml | 48 ti,charge-current:
55 charge will be terminated when current in constant-voltage phase drops
72 - ti,charge-current
91 ti,charge-current = <650>;
|
| H A D | bq24190.yaml | 54 - precharge-current-microamp: maximum charge current during precharge phase
56 - charge-term-current-microamp: a charge cycle terminates when the battery voltage is
75 charge-term-current-microamp = <128000>;
|
| /freebsd/sys/contrib/device-tree/src/arm64/rockchip/ |
| H A D | rk3326-odroid-go2.dts | 42 charge-full-design-microamp-hours = <3000000>;
43 charge-term-current-microamp = <300000>;
44 constant-charge-current-max-microamp = <2000000>;
45 constant-charge-voltage-max-microvolt = <4200000>;
|
| H A D | rk3566-anbernic-rg353vs.dts | 22 charge-full-design-microamp-hours = <3151000>;
23 charge-term-current-microamp = <300000>;
24 constant-charge-current-max-microamp = <2000000>;
25 constant-charge-voltage-max-microvolt = <4200000>;
|