Lines Matching refs:NAND
3 bool "Raw NAND Device Support"
10 NAND initialization process.
24 bool "Support Atmel NAND controller"
27 Enable this driver for NAND flash platforms using an Atmel NAND
69 bool "Support Broadcom NAND controller"
72 Enable the driver for NAND flash on platforms using a Broadcom NAND
76 bool "Support Broadcom NAND controller on bcm6368"
82 bool "Support Broadcom NAND controller on bcm68360"
88 bool "Support Broadcom NAND controller on bcm6838"
94 bool "Support Broadcom NAND controller on bcm6858"
100 bool "Support Broadcom NAND controller on bcm63158"
106 bool "Support TI Davinci NAND controller"
108 Enable this driver for NAND flash controllers available in TI Davinci
117 bool "Support Denali NAND controller as a DT device"
121 Enable the driver for NAND flash on platforms using a Denali NAND
127 Enable the LPC32XX SLC NAND controller.
130 bool "Support OMAP GPMC NAND controller"
134 GPMC controller is used for parallel NAND flash devices, and can
164 Enables support for NAND Flash Controller on some Freescale
172 bool "Support Vybrid's vf610 NAND controller as a DT device"
175 Enable the driver for Vybrid's vf610 NAND flash on platforms
196 bool "Support for NAND on PXA3xx and Armada 370/XP/38x"
203 This enables the driver for the NAND flash device found on
207 bool "Support for NAND on Allwinner SoCs"
215 Enable support for NAND. This option enables the standard and
217 The SPL driver only supports reading from the NAND using DMA
223 int "Allwinner NAND SPL ECC Strength"
227 int "Allwinner NAND SPL ECC Step Size"
231 int "Allwinner NAND SPL Usable Page Size"
247 bool "MXC NAND support"
251 This enables the NAND driver for the NAND flash controller on the
255 bool "MXS NAND support"
263 This enables NAND driver for the NAND flash controller on the
269 bool "Support MXS NAND controller as a DT device"
272 Enable the driver for MXS NAND flash on platforms using
291 bool "Enable use of 1st stage bootloader timing for NAND"
294 This flag prevent U-boot reconfigure NAND flash controller and reuse
295 the NAND timing from 1st stage bootloader.
298 bool "Support for OcteonTX NAND controller"
306 bool "Support Hardware ECC for OcteonTX NAND controller"
311 support ECC for NAND flash controller.
314 bool "Support for NAND controller on STM32MP SoCs"
319 Enables support for NAND Flash chips on SoCs containing the FMC2
320 NAND controller. This controller is found on STM32MP SoCs.
325 bool "Support for NAND controller on Cortina-Access SoCs"
331 Enables support for NAND Flash chips on Coartina-Access SoCs platform
336 comment "Generic NAND options"
339 hex "NAND chip eraseblock size"
342 Number of data bytes in one eraseblock for the NAND chip on the
347 hex "NAND chip page size"
350 Number of data bytes in one page for the NAND chip on the
354 hex "NAND chip OOB size"
357 Number of bytes in the Out-Of-Band area for the NAND chip on
363 bool "Use 16-bit NAND interface"
366 Indicates that NAND device has 16-bit wide data-bus. In absence of this
367 config, bus-width of NAND device is assumed to be either 8-bit and later
369 Above config is useful when NAND device's bus-width information cannot
380 int "NAND max chips"
384 The maximum number of NAND chips per device to be supported.
389 bool "Define U-boot binaries locations in NAND"
397 hex "Location in NAND to read U-Boot from"
405 hex "Location in NAND to read U-Boot from"
413 bool "Enables SPL-NAND driver which supports ELM based"
418 hardware engine and use NAND boot mode.
421 SPL-NAND driver with software ECC correction support.
424 bool "Support Denali NAND controller for SPL"
426 This is a small implementation of the Denali NAND controller
439 bool "Use simple SPL NAND driver"
442 Support for NAND boot using simple NAND drivers that
446 endif # if NAND