#!version:1.0.0.1 #{$microtime} ##File header "#!version:1.0.0.1" can not be edited or deleted, and must be placed in the first line.## ####################################################################################### ## Account 1 Basic Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.enable = {if isset($user_password_1) } account.1.enable = 1 {else} account.1.enable = 0 {/if} account.1.label = {$display_name_1} account.1.display_name = {$display_name_1} account.1.auth_name = {$auth_id_1} account.1.password = {$user_password_1} account.1.user_name = {$user_id_1} account.1.sip_server_host = {$server_address_1} account.1.sip_server_port = {$sip_port_1} account.1.outbound_host = {$outbound_proxy_1} account.1.outbound_port = {$sip_port_1} {if isset($yealink_sip_listen_port)}account.1.sip_listen_port = {$yealink_sip_listen_port}{else}account.1.sip_listen_port = 5060{/if} #Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV; {if $sip_transport_1 == 'udp'}account.1.transport = 0{/if} {if $sip_transport_1 == 'tcp'}account.1.transport = 1{/if} {if $sip_transport_1 == 'tls'}account.1.transport = 2{/if} {if $sip_transport_1 == 'dns srv'}account.1.transport = 3{/if} account.1.outbound_proxy.1.address = {$outbound_proxy_primary_1} account.1.outbound_proxy.2.address = {$outbound_proxy_secondary_1} account.1.outbound_proxy_enable = {if isset($outbound_proxy_primary_1)}1{else}0{/if} {if isset($outbound_proxy_1_port)} account.1.outbound_proxy.1.port = {$outbound_proxy_1_port} {else} account.1.outbound_proxy.1.port = 5060 {/if} {if isset($outbound_proxy_1_port)} account.1.outbound_proxy.2.port = {$outbound_proxy_2_port} {else} account.1.outbound_proxy.2.port = 5060 {/if} ####################################################################################### ## Failback ## ####################################################################################### ## ranges from 1 to 6; ##account.X.reregister_enable = 0 account.1.reregister_enable = 0 account.1.retry_counts = account.1.failback_mode = 0 account.1.failback_timeout = 3600 account.1.naptr_build = 0 account.1.fallback.redundancy_type = 0 account.1.fallback.timeout = {$yealink_outbound_proxy_fallback_interval} account.1.sip_server.1.address = {if $sip_transport_1 == 'dns srv'} account.1.sip_server.1.port = 0 {else} account.1.sip_server.1.port = {$sip_port_1} {/if} #Configure the register expiry time (in seconds), the default value is 3600. account.1.sip_server.1.expires = {$register_expires_1} account.1.sip_server.1.retry_counts = 3 account.1.sip_server.1.failback_mode = 0 account.1.sip_server.1.failback_timeout = 3600 account.1.sip_server.1.register_on_enable = 0 account.1.sip_server.2.address = account.1.sip_server.2.port = 5060 account.1.sip_server.2.expires = 3600 account.1.sip_server.2.retry_counts = 3 account.1.sip_server.2.failback_mode = 0 account.1.sip_server.2.failback_timeout = 3600 account.1.sip_server.2.register_on_enable = 0 account.1.dns_cache_type = 1 account.1.dns_cache_a.1.name = account.1.dns_cache_a.1.ip = account.1.dns_cache_a.1.ttl = 300 account.1.dns_cache_srv.1.name = account.1.dns_cache_srv.1.port = 0 account.1.dns_cache_srv.1.priority = 0 account.1.dns_cache_srv.1.target = account.1.dns_cache_srv.1.weight = 0 account.1.dns_cache_srv.1.ttl = 300 account.1.dns_cache_naptr.1.name = account.1.dns_cache_naptr.1.flags = account.1.dns_cache_naptr.1.order = 0 account.1.dns_cache_naptr.1.preference = 0 account.1.dns_cache_naptr.1.replace = account.1.dns_cache_naptr.1.service = account.1.dns_cache_naptr.1.ttl = 300 account.1.static_cache_pri = 0 ####################################################################################### ## Register Advanced ## ####################################################################################### ## ranges from 1 to 6; ##account.X.sip_server_type = #Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom; account.1.sip_server_type = #Enable or disable the phone to send the account log-off message first and then send account register message when rebooting the phone; 0-Disabled (default), 1-Enabled; account.1.unregister_on_reboot = #Enable or disable the phone to only accept the message from the server; 0-Disabled (default), 1-Enabled; account.1.sip_trust_ctrl = 1 #Configure the timeout (in seconds) for DNS query, the value ranges from 1 to 9, the default value is 8. account.1.dns_query_timeout= #Enable or disable the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled; account.1.srv_ttl_timer_enable = account.1.proxy_require = #Enable or disable the phone to send the MAC address and line number in the Register message; 0-Disabled (default), 1-Enabled; account.1.register_mac = account.1.register_line = #Configure the interval (in seconds) the phone retries to register when account1 fails to register. It ranges from 0 to 1800, the default value is 30. account.1.reg_fail_retry_interval = ######################################################################### ## NAT Settings ## ######################################################################### #Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN; account.1.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if} #Configure the STUN server address. account.1.nat.stun_server = {$stun_server} #Configure the STUN server port, the default value is 3478. account.1.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if} #Enable or disable the NAT keep-alive; 0-Disabled, 1-Default (default), 2-Option, 3-Notify; account.1.nat.udp_update_enable = 3 #Specify the keep-alive interval (in seconds), the default value is 30. account.1.nat.udp_update_time = 30 #Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled; account.1.nat.rport = {$yealink_rport} ####################################################################################### ## AccountX Advance Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.advanced.timer_t1 = 0.5 ##voice_mail.number.X = #Configure the session timer (in seconds), the default value of T1, T2, T3 is 0.5, 4, 5. account.1.advanced.timer_t1 = account.1.advanced.timer_t2 = account.1.advanced.timer_t4 = voice_mail.number.1 = {$voicemail_number} ####################################################################################### ## Subscribe ## ####################################################################################### ## ranges from 1 to 6; ##account.X.subscribe_mwi = account.1.subscribe_mwi = 1 account.1.subscribe_mwi_expires = 3600 #Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled; account.1.subscribe_mwi_to_vm = {$yealink_subscribe_mwi_to_vm} account.1.subscribe_acd_expires= 3600 ####################################################################################### ## BLF List ## ####################################################################################### ## ranges from 1 to 6; ##account.X.blf.blf_list_uri = #Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist". account.1.blf.blf_list_uri = account.1.blf_list_code = account.1.blf_list_barge_in_code = account.1.blf.subscribe_period = 1800 account.1.blf.subscribe_event = account.1.out_dialog_blf_enable = 0 ####################################################################################### ## BLA/SCA ## ####################################################################################### ## ranges from 1 to 6; ##account.X.shared_line = #Assign account1 as shared line; 0-Disabled (default), 1-Broadsoft SCA, 2-BLA; {if isset($shared_line_1) } account.1.shared_line = {$shared_line_1} {else} account.1.shared_line = 0 {/if} #Configure BLA number for account1 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300. account.1.bla_number = account.1.bla_subscribe_period = 300 ####################################################################################### ## Audio Codec ## ####################################################################################### #Audio codecs for account1 (Y ranges from 1 to 11). #Enable or disable the specified codec; 0-Disabled, 1-Enabled; #account.1.codec.Y.enable = #The type of the specified codec. #account.1.codec.Y.payload_type = #The priority of the specified codec. It's available when the codec is enabled. #account.1.codec.Y.priority = #The payload of the specified codec. #account.1.codec.Y.rtpmap = account.1.codec.1.enable = 1 account.1.codec.1.payload_type = PCMU account.1.codec.1.priority = 2 account.1.codec.1.rtpmap = 0 account.1.codec.2.enable = 1 account.1.codec.2.payload_type = PCMA account.1.codec.2.priority = 3 account.1.codec.2.rtpmap = 8 account.1.codec.3.enable = 0 account.1.codec.3.payload_type = G723_53 account.1.codec.3.priority =0 account.1.codec.3.rtpmap = 4 account.1.codec.4.enable = 0 account.1.codec.4.payload_type = G723_63 account.1.codec.4.priority = 0 account.1.codec.4.rtpmap = 4 account.1.codec.5.enable = 1 account.1.codec.5.payload_type = G729 account.1.codec.5.priority = 3 account.1.codec.5.rtpmap = 18 account.1.codec.6.enable = 1 account.1.codec.6.payload_type = G722 account.1.codec.6.priority = 1 account.1.codec.6.rtpmap = 9 account.1.codec.7.enable = 0 account.1.codec.7.payload_type = iLBC account.1.codec.7.priority = 0 account.1.codec.7.rtpmap = 106 account.1.codec.8.enable = 0 account.1.codec.8.payload_type = G726-16 account.1.codec.8.priority = 0 account.1.codec.8.rtpmap = 103 account.1.codec.9.enable = 0 account.1.codec.9.payload_type = G726-24 account.1.codec.9.priority = 0 account.1.codec.9.rtpmap = 104 account.1.codec.10.enable = 0 account.1.codec.10.payload_type = G726-32 account.1.codec.10.priority = 0 account.1.codec.10.rtpmap = 102 account.1.codec.11.enable = 0 account.1.codec.11.payload_type = G726-40 account.1.codec.11.priority = 0 account.1.codec.11.rtpmap = 105 account.1.codec.12.enable = 0 account.1.codec.12.payload_type = GSM account.1.codec.12.priority = 0 account.1.codec.12.rtpmap = 3 ####################################################################################### ## Audio Advanced ## ####################################################################################### #Specify whether to encrypt the SIP messages; 0-Disabled (default), 1-Forced, 2-Negotiated; account.1.srtp_encryption = {$yealink_srtp_encryption} #Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60. account.1.ptime = ####################################################################################### ## Anonymous Call ## ####################################################################################### account.1.anonymous_call = 0 account.1.anonymous_call_oncode = account.1.anonymous_call_offcode = account.1.reject_anonymous_call = account.1.anonymous_reject_oncode = account.1.anonymous_reject_offcode = ####################################################################################### ## Pickup Code ## ####################################################################################### account.1.dialoginfo_callpickup = 0 #Configure the directed and group pickup codes for account 1, the settings on a per-account basis take precedence over the settings on the phone. account.1.group_pickup_code = account.1.direct_pickup_code = ####################################################################################### ## DTMF ## ####################################################################################### #Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO; account.1.dtmf.type = #Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event; account.1.dtmf.info_type = #Configure the RFC2833 payload. It ranges from 96 to 255, the default value is 101. account.1.dtmf.dtmf_payload = ####################################################################################### ## Alert info ## ####################################################################################### #Enable or disable to use the Distinctive Ring Tones; 0-Disabled , 1-Enabled(default); account.1.alert_info_url_enable = #Assign a ringtone for account1. The system ring tones are: common (default), Ring1.wav - Ring8.wav. #If you set the custom ring tone (Busy.wav) for the phone, the value is: account.1.ringtone.ring_type = Config:Busy.wav #If you set the system ring tone (Ring2.wav) for the phone, the value is: account.1.ringtone.ring_type = Resource:Ring2.wav account.1.ringtone.ring_type = account.1.picture_info_enable = 1 ####################################################################################### ## Conference ## ####################################################################################### #Configure the conference type; 0-Local (default), 2-Network Conference; account.1.conf_type = #Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference". account.1.conf_uri = ####################################################################################### ## cid_source ## ####################################################################################### #Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM; account.1.cid_source = {$yealink_cid_source} account.1.cid_source_privacy = 1 account.1.cid_source_ppi = 1 #Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916; account.1.cp_source = 2 ####################################################################################### ## Session Timer ## ####################################################################################### #Enable or disable the session timer, 0-Disabled (default), 1-Enabled; account.1.session_timer.enable = {$yealink_session_timer} #Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999. account.1.session_timer.expires = #Configure the session timer refresher; 0-Uac (default), 1-Uas; account.1.session_timer.refresher = ####################################################################################### ## Music on Hold ## ####################################################################################### #Configure the type of Music on Hold; 0-Send the INVITE request to Music on Hold Server then hold the call; 1-Hold the call then send the INVITE request to Music on Hold Server; #Require reboot; account.1.music_on_hold_type = account.1.music_server_uri = ####################################################################################### ## Advanced ## ####################################################################################### #Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled; account.1.auto_answer = #Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default); account.1.missed_calllog = #Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled; account.1.100rel_enable = {$yealink_retransmission} #Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled; account.1.enable_user_equal_phone = #Enable or disable the simplified header field feature; 0-Disabled, 1-Enabled (default); account.1.compact_header_enable = ####################################################################################### ## DND ## ####################################################################################### account.1.dnd.enable = account.1.dnd.on_code = account.1.dnd.off_code = ####################################################################################### ## Call Forward ## ####################################################################################### account.1.always_fwd.enable = account.1.always_fwd.target = account.1.always_fwd.off_code = account.1.always_fwd.on_code = account.1.busy_fwd.enable = account.1.busy_fwd.target = account.1.busy_fwd.off_code = account.1.busy_fwd.on_code = #Enable or disable the no answer forward feature for account1; 0-Disabled (default), 1-Enabled; #Configure the waiting ring times before forwarding. It ranges from 0 to 20, the default value is 2. account.1.timeout_fwd.enable = account.1.timeout_fwd.target = account.1.timeout_fwd.timeout = account.1.timeout_fwd.off_code = account.1.timeout_fwd.on_code = ####################################################################################### ## Broadsoft Hoteling ## ####################################################################################### account.1.hoteling.enable = 0 account.1.hoteling.user_id = 0 account.1.hoteling.password = 0 account.1.hoteling.auto_login_enable = 0 ####################################################################################### ## Broadsoft ACD ## ####################################################################################### account.1.acd.enable = 0 account.1.acd.unavailable_reason_enable = 0 account.1.acd.available = 0 account.1.acd.initial_state = 1 ####################################################################################### ## Broadsoft ACD Call Center ## ####################################################################################### #Configure the ACD reason code of Broadsoft.(The valus of Y must be consecutive numbers.) #account.1.bw_acd_reason_code.Y = 500(lunch time) account.1.bw_acd_reason_code.1 = account.1.reason_code.1 = account.1.reason_code_name.1 = 0 account.1.bw_disp_code.1 = account.1.bw_disp_code_name.1 = account.1.supervisor_info_code.1 = account.1.supervisor_info_code_name.1 = ####################################################################################### ## Broadsoft Call Center ## ####################################################################################### account.1.call_center.call_info_enable = 0 account.1.call_center.show_call_info_time = 30 account.1.call_center.disp_code_enable = 0 account.1.call_center.trace_enable = 0 account.1.call_center.emergency_enable = 0 account.1.call_center.queue_status_enable = 0 account.1.call_center.queue_status_light_enable = 0 ####################################################################################### ## Broadsoft XSI ## ####################################################################################### account.1.xsi.user = account.1.xsi.password = account.1.xsi.host = account.1.xsi.server_type = account.1.xsi.port = ####################################################################################### ## Account 2 Basic Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.enable = {if isset($user_password_2) } account.2.enable = 1 {else} account.2.enable = 0 {/if} account.2.label = {$display_name_2} account.2.display_name = {$display_name_2} account.2.auth_name = {$auth_id_2} account.2.password = {$user_password_2} account.2.user_name = {$user_id_2} account.2.sip_server_host = {$server_address_2} account.2.sip_server_port = {$sip_port_2} account.2.outbound_host = {$outbound_proxy_2} account.2.outbound_port = {$sip_port_2} {if isset($yealink_sip_listen_port)}account.2.sip_listen_port = {$yealink_sip_listen_port}{else}account.2.sip_listen_port = 5060{/if} account.2.sip_listen_port = 5060 #Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV; {if $sip_transport_2 == 'udp'}account.2.transport = 0{/if} {if $sip_transport_2 == 'tcp'}account.2.transport = 1{/if} {if $sip_transport_2 == 'tls'}account.2.transport = 2{/if} {if $sip_transport_2 == 'dns srv'}account.2.transport = 3{/if} account.2.outbound_proxy.1.address = {$outbound_proxy_primary_2} account.2.outbound_proxy.2.address = {$outbound_proxy_secondary_2} account.2.outbound_proxy_enable = {if isset($outbound_proxy_primary_2)}1{else}0{/if} ####################################################################################### ## Failback ## ####################################################################################### ## ranges from 1 to 6; ##account.X.reregister_enable = 0 account.2.reregister_enable = 0 account.2.retry_counts = account.2.failback_mode = 0 account.2.failback_timeout = 3600 account.2.naptr_build = 0 account.2.fallback.redundancy_type = 0 account.2.fallback.timeout = {$yealink_outbound_proxy_fallback_interval} account.2.sip_server.1.address = account.2.sip_server.1.port = 5060 #Configure the register expiry time (in seconds), the default value is 3600. account.2.sip_server.1.expires = {$register_expires_2} account.2.sip_server.1.retry_counts = 3 account.2.sip_server.1.failback_mode = 0 account.2.sip_server.1.failback_timeout = 3600 account.2.sip_server.1.register_on_enable = 0 account.2.sip_server.2.address = account.2.sip_server.2.port = 5060 account.2.sip_server.2.expires = 3600 account.2.sip_server.2.retry_counts = 3 account.2.sip_server.2.failback_mode = 0 account.2.sip_server.2.failback_timeout = 3600 account.2.sip_server.2.register_on_enable = 0 account.2.dns_cache_type = 1 account.2.dns_cache_a.1.name = account.2.dns_cache_a.1.ip = account.2.dns_cache_a.1.ttl = 300 account.2.dns_cache_srv.0.name = account.2.dns_cache_srv.0.port = 0 account.2.dns_cache_srv.0.priority = 0 account.2.dns_cache_srv.0.target = account.2.dns_cache_srv.0.weight = 0 account.2.dns_cache_srv.0.ttl = 300 account.2.dns_cache_naptr.0.name = account.2.dns_cache_naptr.0.flags = account.2.dns_cache_naptr.0.order = 0 account.2.dns_cache_naptr.0.preference = 0 account.2.dns_cache_naptr.0.replace = account.2.dns_cache_naptr.0.service = account.2.dns_cache_naptr.0.ttl = 300 account.2.static_cache_pri = 0 ####################################################################################### ## Register Advanced ## ####################################################################################### ## ranges from 1 to 6; ##account.X.sip_server_type = #Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom; account.2.sip_server_type = #Enable or disable the phone to send the account log-off message first and then send account register message when rebooting the phone; 0-Disabled (default), 1-Enabled; account.2.unregister_on_reboot = #Enable or disable the phone to only accept the message from the server; 0-Disabled (default), 1-Enabled; account.2.sip_trust_ctrl = 1 #Configure the timeout (in seconds) for DNS query, the value ranges from 1 to 9, the default value is 8. account.2.dns_query_timeout= #Enable or disable the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled; account.2.srv_ttl_timer_enable = account.2.proxy_require = #Enable or disable the phone to send the MAC address and line number in the Register message; 0-Disabled (default), 1-Enabled; account.2.register_mac = account.2.register_line = #Configure the interval (in seconds) the phone retries to register when account1 fails to register. It ranges from 0 to 1800, the default value is 30. account.2.reg_fail_retry_interval = ######################################################################### ## NAT Settings ## ######################################################################### #Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN; account.2.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if} #Configure the STUN server address. account.2.nat.stun_server = {$stun_server} #Configure the STUN server port, the default value is 3478. account.2.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if} #Enable or disable the NAT keep-alive; 0-Disabled, 1-Default (default), 2-Option, 3-Notify; account.2.nat.udp_update_enable = 1 #Specify the keep-alive interval (in seconds), the default value is 30. account.2.nat.udp_update_time = 30 #Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled; account.2.nat.rport = {$yealink_rport} ####################################################################################### ## Account2 Advance Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.advanced.timer_t1 = 0.5 ##voice_mail.number.X = #Configure the session timer (in seconds), the default value of T1, T2, T3 is 0.5, 4, 5. account.2.advanced.timer_t1 = 0.5 account.2.advanced.timer_t2 = 4 account.2.advanced.timer_t4 = 5 voice_mail.number.2 = *97 ####################################################################################### ## Subscribe ## ####################################################################################### ## ranges from 1 to 6; ##account.X.subscribe_mwi = account.2.subscribe_mwi = 1 account.2.subscribe_mwi_expires = 3600 #Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled; account.2.subscribe_mwi_to_vm = {$yealink_subscribe_mwi_to_vm} account.2.subscribe_acd_expires= 3600 ####################################################################################### ## BLF List ## ####################################################################################### ## ranges from 1 to 6; ##account.X.blf.blf_list_uri = #Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist". account.2.blf.blf_list_uri = account.2.blf_list_code = account.2.blf_list_barge_in_code = account.2.blf.subscribe_period = 1800 account.2.blf.subscribe_event = account.2.out_dialog_blf_enable = 0 ####################################################################################### ## BLA/SCA ## ####################################################################################### ## ranges from 1 to 6; ##account.X.shared_line = #Assign account1 as shared line; 0-Disabled (default), 1-Broadsoft SCA, 2-BLA; {if isset($shared_line_2) } account.2.shared_line = {$shared_line_2} {else} account.2.shared_line = 0 {/if} #Configure BLA number for account1 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300. account.2.bla_number = account.2.bla_subscribe_period = 300 ####################################################################################### ## Audio Codec ## ####################################################################################### #Audio codecs for account1 (Y ranges from 1 to 11). #Enable or disable the specified codec; 0-Disabled, 1-Enabled; #account.2.codec.Y.enable = #The type of the specified codec. #account.2.codec.Y.payload_type = #The priority of the specified codec. It's available when the codec is enabled. #account.2.codec.Y.priority = #The payload of the specified codec. #account.2.codec.Y.rtpmap = account.2.codec.1.enable = 1 account.2.codec.1.payload_type = PCMU account.2.codec.1.priority = 2 account.2.codec.1.rtpmap = 0 account.2.codec.2.enable = 1 account.2.codec.2.payload_type = PCMA account.2.codec.2.priority = 3 account.2.codec.2.rtpmap = 8 account.2.codec.3.enable = 0 account.2.codec.3.payload_type = G723_53 account.2.codec.3.priority =0 account.2.codec.3.rtpmap = 4 account.2.codec.4.enable = 0 account.2.codec.4.payload_type = G723_63 account.2.codec.4.priority = 0 account.2.codec.4.rtpmap = 4 account.2.codec.5.enable = 1 account.2.codec.5.payload_type = G729 account.2.codec.5.priority = 3 account.2.codec.5.rtpmap = 18 account.2.codec.6.enable = 1 account.2.codec.6.payload_type = G722 account.2.codec.6.priority = 1 account.2.codec.6.rtpmap = 9 account.2.codec.7.enable = 0 account.2.codec.7.payload_type = iLBC account.2.codec.7.priority = 0 account.2.codec.7.rtpmap = 106 account.2.codec.8.enable = 0 account.2.codec.8.payload_type = G726-16 account.2.codec.8.priority = 0 account.2.codec.8.rtpmap = 103 account.2.codec.9.enable = 0 account.2.codec.9.payload_type = G726-24 account.2.codec.9.priority = 0 account.2.codec.9.rtpmap = 104 account.2.codec.10.enable = 0 account.2.codec.10.payload_type = G726-32 account.2.codec.10.priority = 0 account.2.codec.10.rtpmap = 102 account.2.codec.11.enable = 0 account.2.codec.11.payload_type = G726-40 account.2.codec.11.priority = 0 account.2.codec.11.rtpmap = 105 account.2.codec.12.enable = 0 account.2.codec.12.payload_type = GSM account.2.codec.12.priority = 0 account.2.codec.12.rtpmap = 3 ####################################################################################### ## Audio Advanced ## ####################################################################################### #Specify whether to encrypt the SIP messages; 0-Disabled (default), 1-Forced, 2-Negotiated; account.2.srtp_encryption = #Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60. account.2.ptime = ####################################################################################### ## Anonymous Call ## ####################################################################################### account.2.anonymous_call = 0 account.2.anonymous_call_oncode = account.2.anonymous_call_offcode = account.2.reject_anonymous_call = account.2.anonymous_reject_oncode = account.2.anonymous_reject_offcode = ####################################################################################### ## Pickup Code ## ####################################################################################### account.2.dialoginfo_callpickup = 0 #Configure the directed and group pickup codes for account 1, the settings on a per-account basis take precedence over the settings on the phone. account.2.group_pickup_code = account.2.direct_pickup_code = ####################################################################################### ## DTMF ## ####################################################################################### #Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO; account.2.dtmf.type = #Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event; account.2.dtmf.info_type = #Configure the RFC2833 payload. It ranges from 96 to 255, the default value is 101. account.2.dtmf.dtmf_payload = ####################################################################################### ## Alert info ## ####################################################################################### #Enable or disable to use the Distinctive Ring Tones; 0-Disabled , 1-Enabled(default); account.2.alert_info_url_enable = #Assign a ringtone for account2. The system ring tones are: common (default), Ring1.wav - Ring8.wav. #If you set the custom ring tone (Busy.wav) for the phone, the value is: account.2.ringtone.ring_type = Config:Busy.wav #If you set the system ring tone (Ring2.wav) for the phone, the value is: account.2.ringtone.ring_type = Resource:Ring2.wav account.2.ringtone.ring_type = account.2.picture_info_enable = 1 ####################################################################################### ## Conference ## ####################################################################################### #Configure the conference type; 0-Local (default), 2-Network Conference; account.2.conf_type = #Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference". account.2.conf_uri = ####################################################################################### ## cid source ## ####################################################################################### #Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM; account.2.cid_source = {$yealink_cid_source} account.2.cid_source_privacy = 1 account.2.cid_source_ppi = 1 #Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916; account.2.cp_source = 2 ####################################################################################### ## Session Timer ## ####################################################################################### #Enable or disable the session timer, 0-Disabled (default), 1-Enabled; account.2.session_timer.enable = {$yealink_session_timer} #Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999. account.2.session_timer.expires = #Configure the session timer refresher; 0-Uac (default), 1-Uas; account.2.session_timer.refresher = ####################################################################################### ## Music on Hold ## ####################################################################################### #Configure the type of Music on Hold; 0-Send the INVITE request to Music on Hold Server then hold the call; 1-Hold the call then send the INVITE request to Music on Hold Server; #Require reboot; account.2.music_on_hold_type = account.2.music_server_uri = ####################################################################################### ## Advanced ## ####################################################################################### #Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled; account.2.auto_answer = #Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default); account.2.missed_calllog = #Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled; account.2.100rel_enable = {$yealink_retransmission} #Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled; account.2.enable_user_equal_phone = #Enable or disable the simplified header field feature; 0-Disabled, 1-Enabled (default); account.2.compact_header_enable = ####################################################################################### ## DND ## ####################################################################################### account.2.dnd.enable = account.2.dnd.on_code = account.2.dnd.off_code = ####################################################################################### ## Call Forward ## ####################################################################################### #Enable or disable the busy forward feature for account; 0-Disabled (default), 1-Enabled; account.2.always_fwd.enable = account.2.always_fwd.target = account.2.always_fwd.off_code = account.2.always_fwd.on_code = account.2.busy_fwd.enable = account.2.busy_fwd.target = account.2.busy_fwd.off_code = account.2.busy_fwd.on_code = #Enable or disable the no answer forward feature for account1; 0-Disabled (default), 1-Enabled; #Configure the waiting ring times before forwarding. It ranges from 0 to 20, the default value is 2. account.2.timeout_fwd.enable = account.2.timeout_fwd.target = account.2.timeout_fwd.timeout = account.2.timeout_fwd.off_code = account.2.timeout_fwd.on_code = ####################################################################################### ## Broadsoft Hoteling ## ####################################################################################### account.2.hoteling.enable = 0 account.2.hoteling.user_id = 0 account.2.hoteling.password = 0 account.2.hoteling.auto_login_enable = 0 ####################################################################################### ## Broadsoft ACD ## ####################################################################################### account.2.acd.enable = 0 account.2.acd.unavailable_reason_enable = 0 account.2.acd.available = 0 account.2.acd.initial_state = 1 ####################################################################################### ## Broadsoft ACD Call Center ## ####################################################################################### #Configure the ACD reason code of Broadsoft.(The valus of Y must be consecutive numbers.) #account.2.bw_acd_reason_code.Y = 500(lunch time) account.2.bw_acd_reason_code.1 = account.2.reason_code.1 = account.2.reason_code_name.1 = 0 account.2.bw_disp_code.1 = account.2.bw_disp_code_name.1 = account.2.supervisor_info_code.1 = account.2.supervisor_info_code_name.1 = ####################################################################################### ## Broadsoft Call Center ## ####################################################################################### account.2.call_center.call_info_enable = 0 account.2.call_center.show_call_info_time = 30 account.2.call_center.disp_code_enable = 0 account.2.call_center.trace_enable = 0 account.2.call_center.emergency_enable = 0 account.2.call_center.queue_status_enable = 0 account.2.call_center.queue_status_light_enable = 0 ####################################################################################### ## Broadsoft XSI ## ####################################################################################### account.2.xsi.user = account.2.xsi.password = account.2.xsi.host = account.2.xsi.server_type = account.2.xsi.port = ####################################################################################### ## Time ## ####################################################################################### #Configure the time zone and time zone name. The time zone ranges from -11 to +12, the default value is +8. #local_time.time_zone = +8 #local_time.time_zone_name = China(Beijing) local_time.time_zone = {$yealink_time_zone} local_time.time_zone_name = {$yealink_time_zone_name} ####################################################################################### ## NETWORK ## ####################################################################################### ####################################################################################### ## Account 3 Basic Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.enable = {if isset($user_password_3) } account.3.enable = 1 {else} account.3.enable = 0 {/if} account.3.label = {$display_name_3} account.3.display_name = {$display_name_3} account.3.auth_name = {$auth_id_3} account.3.password = {$user_password_3} account.3.user_name = {$user_id_3} account.3.sip_server_host = {$server_address_3} account.3.sip_server_port = {$sip_port_3} account.3.outbound_host = {$outbound_proxy_3} account.3.outbound_port = {$sip_port_3} {if isset($yealink_sip_listen_port)}account.3.sip_listen_port = {$yealink_sip_listen_port}{else}account.3.sip_listen_port = 5060{/if} account.3.sip_listen_port = 5060 #Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV; {if $sip_transport_3 == 'udp'}account.3.transport = 0{/if} {if $sip_transport_3 == 'tcp'}account.3.transport = 1{/if} {if $sip_transport_3 == 'tls'}account.3.transport = 2{/if} {if $sip_transport_3 == 'dns srv'}account.3.transport = 3{/if} account.3.outbound_proxy.1.address = {$outbound_proxy_primary_3} account.3.outbound_proxy.2.address = {$outbound_proxy_secondary_3} account.3.outbound_proxy_enable = {if isset($outbound_proxy_primary_3)}1{else}0{/if} ####################################################################################### ## Failback ## ####################################################################################### ## ranges from 1 to 6; ##account.X.reregister_enable = 0 account.3.reregister_enable = 0 account.3.retry_counts = account.3.failback_mode = 0 account.3.failback_timeout = 3600 account.3.naptr_build = 0 account.3.fallback.redundancy_type = 0 account.3.fallback.timeout = {$yealink_outbound_proxy_fallback_interval} account.3.sip_server.1.address = account.3.sip_server.1.port = 5060 #Configure the register expiry time (in seconds), the default value is 3600. account.3.sip_server.1.expires = {$register_expires_3} account.3.sip_server.1.retry_counts = 3 account.3.sip_server.1.failback_mode = 0 account.3.sip_server.1.failback_timeout = 3600 account.3.sip_server.1.register_on_enable = 0 account.3.sip_server.2.address = account.3.sip_server.2.port = 5060 account.3.sip_server.2.expires = 3600 account.3.sip_server.2.retry_counts = 3 account.3.sip_server.2.failback_mode = 0 account.3.sip_server.2.failback_timeout = 3600 account.3.sip_server.2.register_on_enable = 0 account.3.dns_cache_type = 1 account.3.dns_cache_a.1.name = account.3.dns_cache_a.1.ip = account.3.dns_cache_a.1.ttl = 300 account.3.dns_cache_srv.0.name = account.3.dns_cache_srv.0.port = 0 account.3.dns_cache_srv.0.priority = 0 account.3.dns_cache_srv.0.target = account.3.dns_cache_srv.0.weight = 0 account.3.dns_cache_srv.0.ttl = 300 account.3.dns_cache_naptr.0.name = account.3.dns_cache_naptr.0.flags = account.3.dns_cache_naptr.0.order = 0 account.3.dns_cache_naptr.0.preference = 0 account.3.dns_cache_naptr.0.replace = account.3.dns_cache_naptr.0.service = account.3.dns_cache_naptr.0.ttl = 300 account.3.static_cache_pri = 0 ####################################################################################### ## Register Advanced ## ####################################################################################### ## ranges from 1 to 6; ##account.X.sip_server_type = #Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom; account.3.sip_server_type = #Enable or disable the phone to send the account log-off message first and then send account register message when rebooting the phone; 0-Disabled (default), 1-Enabled; account.3.unregister_on_reboot = #Enable or disable the phone to only accept the message from the server; 0-Disabled (default), 1-Enabled; account.3.sip_trust_ctrl = 1 #Configure the timeout (in seconds) for DNS query, the value ranges from 1 to 9, the default value is 8. account.3.dns_query_timeout= #Enable or disable the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled; account.3.srv_ttl_timer_enable = account.3.proxy_require = #Enable or disable the phone to send the MAC address and line number in the Register message; 0-Disabled (default), 1-Enabled; account.3.register_mac = account.3.register_line = #Configure the interval (in seconds) the phone retries to register when account1 fails to register. It ranges from 0 to 1800, the default value is 30. account.3.reg_fail_retry_interval = ######################################################################### ## NAT Settings ## ######################################################################### #Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN; account.3.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if} #Configure the STUN server address. account.3.nat.stun_server = {$stun_server} #Configure the STUN server port, the default value is 3478. account.3.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if} #Enable or disable the NAT keep-alive; 0-Disabled, 1-Default (default), 2-Option, 3-Notify; account.3.nat.udp_update_enable = 1 #Specify the keep-alive interval (in seconds), the default value is 30. account.3.nat.udp_update_time = 30 #Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled; account.3.nat.rport = {$yealink_rport} ####################################################################################### ## Account3 Advance Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.advanced.timer_t1 = 0.5 ##voice_mail.number.X = #Configure the session timer (in seconds), the default value of T1, T2, T3 is 0.5, 4, 5. account.3.advanced.timer_t1 = 0.5 account.3.advanced.timer_t2 = 4 account.3.advanced.timer_t4 = 5 voice_mail.number.3 = *97 ####################################################################################### ## Subscribe ## ####################################################################################### ## ranges from 1 to 6; ##account.X.subscribe_mwi = account.3.subscribe_mwi = 1 account.3.subscribe_mwi_expires = 3600 #Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled; account.3.subscribe_mwi_to_vm = {$yealink_subscribe_mwi_to_vm} account.3.subscribe_acd_expires= 3600 ####################################################################################### ## BLF List ## ####################################################################################### ## ranges from 1 to 6; ##account.X.blf.blf_list_uri = #Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist". account.3.blf.blf_list_uri = account.3.blf_list_code = account.3.blf_list_barge_in_code = account.3.blf.subscribe_period = 1800 account.3.blf.subscribe_event = account.3.out_dialog_blf_enable = 0 ####################################################################################### ## BLA/SCA ## ####################################################################################### ## ranges from 1 to 6; ##account.X.shared_line = #Assign account1 as shared line; 0-Disabled (default), 1-Broadsoft SCA, 2-BLA; {if isset($shared_line_3) } account.3.shared_line = {$shared_line_3} {else} account.3.shared_line = 0 {/if} #Configure BLA number for account1 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300. account.3.bla_number = account.3.bla_subscribe_period = 300 ####################################################################################### ## Audio Codec ## ####################################################################################### #Audio codecs for account1 (Y ranges from 1 to 11). #Enable or disable the specified codec; 0-Disabled, 1-Enabled; #account.3.codec.Y.enable = #The type of the specified codec. #account.3.codec.Y.payload_type = #The priority of the specified codec. It's available when the codec is enabled. #account.3.codec.Y.priority = #The payload of the specified codec. #account.3.codec.Y.rtpmap = account.3.codec.1.enable = 1 account.3.codec.1.payload_type = PCMU account.3.codec.1.priority = 2 account.3.codec.1.rtpmap = 0 account.3.codec.2.enable = 1 account.3.codec.2.payload_type = PCMA account.3.codec.2.priority = 3 account.3.codec.2.rtpmap = 8 account.3.codec.3.enable = 0 account.3.codec.3.payload_type = G723_53 account.3.codec.3.priority =0 account.3.codec.3.rtpmap = 4 account.3.codec.4.enable = 0 account.3.codec.4.payload_type = G723_63 account.3.codec.4.priority = 0 account.3.codec.4.rtpmap = 4 account.3.codec.5.enable = 1 account.3.codec.5.payload_type = G729 account.3.codec.5.priority = 3 account.3.codec.5.rtpmap = 18 account.3.codec.6.enable = 1 account.3.codec.6.payload_type = G722 account.3.codec.6.priority = 1 account.3.codec.6.rtpmap = 9 account.3.codec.7.enable = 0 account.3.codec.7.payload_type = iLBC account.3.codec.7.priority = 0 account.3.codec.7.rtpmap = 106 account.3.codec.8.enable = 0 account.3.codec.8.payload_type = G726-16 account.3.codec.8.priority = 0 account.3.codec.8.rtpmap = 103 account.3.codec.9.enable = 0 account.3.codec.9.payload_type = G726-24 account.3.codec.9.priority = 0 account.3.codec.9.rtpmap = 104 account.3.codec.10.enable = 0 account.3.codec.10.payload_type = G726-32 account.3.codec.10.priority = 0 account.3.codec.10.rtpmap = 102 account.3.codec.11.enable = 0 account.3.codec.11.payload_type = G726-40 account.3.codec.11.priority = 0 account.3.codec.11.rtpmap = 105 account.3.codec.12.enable = 0 account.3.codec.12.payload_type = GSM account.3.codec.12.priority = 0 account.3.codec.12.rtpmap = 3 ####################################################################################### ## Audio Advanced ## ####################################################################################### #Specify whether to encrypt the SIP messages; 0-Disabled (default), 1-Forced, 2-Negotiated; account.3.srtp_encryption = #Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60. account.3.ptime = ####################################################################################### ## Anonymous Call ## ####################################################################################### account.3.anonymous_call = 0 account.3.anonymous_call_oncode = account.3.anonymous_call_offcode = account.3.reject_anonymous_call = account.3.anonymous_reject_oncode = account.3.anonymous_reject_offcode = ####################################################################################### ## Pickup Code ## ####################################################################################### account.3.dialoginfo_callpickup = 0 #Configure the directed and group pickup codes for account 1, the settings on a per-account basis take precedence over the settings on the phone. account.3.group_pickup_code = account.3.direct_pickup_code = ####################################################################################### ## DTMF ## ####################################################################################### #Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO; account.3.dtmf.type = #Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event; account.3.dtmf.info_type = #Configure the RFC2833 payload. It ranges from 96 to 255, the default value is 101. account.3.dtmf.dtmf_payload = ####################################################################################### ## Alert info ## ####################################################################################### #Enable or disable to use the Distinctive Ring Tones; 0-Disabled , 1-Enabled(default); account.3.alert_info_url_enable = #Assign a ringtone for account2. The system ring tones are: common (default), Ring1.wav - Ring8.wav. #If you set the custom ring tone (Busy.wav) for the phone, the value is: account.2.ringtone.ring_type = Config:Busy.wav #If you set the system ring tone (Ring2.wav) for the phone, the value is: account.2.ringtone.ring_type = Resource:Ring2.wav account.3.ringtone.ring_type = account.3.picture_info_enable = 1 ####################################################################################### ## Conference ## ####################################################################################### #Configure the conference type; 0-Local (default), 2-Network Conference; account.3.conf_type = #Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference". account.3.conf_uri = ####################################################################################### ## cid source ## ####################################################################################### #Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM; account.3.cid_source = {$yealink_cid_source} account.3.cid_source_privacy = 1 account.3.cid_source_ppi = 1 #Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916; account.3.cp_source = 2 ####################################################################################### ## Session Timer ## ####################################################################################### #Enable or disable the session timer, 0-Disabled (default), 1-Enabled; account.3.session_timer.enable = {$yealink_session_timer} #Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999. account.3.session_timer.expires = #Configure the session timer refresher; 0-Uac (default), 1-Uas; account.3.session_timer.refresher = ####################################################################################### ## Music on Hold ## ####################################################################################### #Configure the type of Music on Hold; 0-Send the INVITE request to Music on Hold Server then hold the call; 1-Hold the call then send the INVITE request to Music on Hold Server; #Require reboot; account.3.music_on_hold_type = account.3.music_server_uri = ####################################################################################### ## Advanced ## ####################################################################################### #Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled; account.3.auto_answer = #Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default); account.3.missed_calllog = #Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled; account.3.100rel_enable = {$yealink_retransmission} #Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled; account.3.enable_user_equal_phone = #Enable or disable the simplified header field feature; 0-Disabled, 1-Enabled (default); account.3.compact_header_enable = ####################################################################################### ## DND ## ####################################################################################### account.3.dnd.enable = account.3.dnd.on_code = account.3.dnd.off_code = ####################################################################################### ## Call Forward ## ####################################################################################### #Enable or disable the busy forward feature for account; 0-Disabled (default), 1-Enabled; account.3.always_fwd.enable = account.3.always_fwd.target = account.3.always_fwd.off_code = account.3.always_fwd.on_code = account.3.busy_fwd.enable = account.3.busy_fwd.target = account.3.busy_fwd.off_code = account.3.busy_fwd.on_code = #Enable or disable the no answer forward feature for account1; 0-Disabled (default), 1-Enabled; #Configure the waiting ring times before forwarding. It ranges from 0 to 20, the default value is 2. account.3.timeout_fwd.enable = account.3.timeout_fwd.target = account.3.timeout_fwd.timeout = account.3.timeout_fwd.off_code = account.3.timeout_fwd.on_code = ####################################################################################### ## Broadsoft Hoteling ## ####################################################################################### account.3.hoteling.enable = 0 account.3.hoteling.user_id = 0 account.3.hoteling.password = 0 account.3.hoteling.auto_login_enable = 0 ####################################################################################### ## Broadsoft ACD ## ####################################################################################### account.3.acd.enable = 0 account.3.acd.unavailable_reason_enable = 0 account.3.acd.available = 0 account.3.acd.initial_state = 1 ####################################################################################### ## Broadsoft ACD Call Center ## ####################################################################################### #Configure the ACD reason code of Broadsoft.(The valus of Y must be consecutive numbers.) #account.3.bw_acd_reason_code.Y = 500(lunch time) account.3.bw_acd_reason_code.1 = account.3.reason_code.1 = account.3.reason_code_name.1 = 0 account.3.bw_disp_code.1 = account.3.bw_disp_code_name.1 = account.3.supervisor_info_code.1 = account.3.supervisor_info_code_name.1 = ####################################################################################### ## Broadsoft Call Center ## ####################################################################################### account.3.call_center.call_info_enable = 0 account.3.call_center.show_call_info_time = 30 account.3.call_center.disp_code_enable = 0 account.3.call_center.trace_enable = 0 account.3.call_center.emergency_enable = 0 account.3.call_center.queue_status_enable = 0 account.3.call_center.queue_status_light_enable = 0 ####################################################################################### ## Broadsoft XSI ## ####################################################################################### account.3.xsi.user = account.3.xsi.password = account.3.xsi.host = account.3.xsi.server_type = account.3.xsi.port = ####################################################################################### ## NETWORK ## ####################################################################################### ####################################################################################### ## Account 4 Basic Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.enable = {if isset($user_password_4) } account.4.enable = 1 {else} account.4.enable = 0 {/if} account.4.label = {$display_name_4} account.4.display_name = {$display_name_4} account.4.auth_name = {$auth_id_4} account.4.password = {$user_password_4} account.4.user_name = {$user_id_4} account.4.sip_server_host = {$server_address_4} account.4.sip_server_port = {$sip_port_4} account.4.outbound_host = {$outbound_proxy_4} account.4.outbound_port = {$sip_port_4} {if isset($yealink_sip_listen_port)}account.4.sip_listen_port = {$yealink_sip_listen_port}{else}account.4.sip_listen_port = 5060{/if} account.4.sip_listen_port = 5060 #Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV; {if $sip_transport_4 == 'udp'}account.4.transport = 0{/if} {if $sip_transport_4 == 'tcp'}account.4.transport = 1{/if} {if $sip_transport_4 == 'tls'}account.4.transport = 2{/if} {if $sip_transport_4 == 'dns srv'}account.4.transport = 3{/if} account.4.outbound_proxy.1.address = {$outbound_proxy_primary_4} account.4.outbound_proxy.2.address = {$outbound_proxy_secondary_4} account.4.outbound_proxy_enable = {if isset($outbound_proxy_primary_4)}1{else}0{/if} ####################################################################################### ## Failback ## ####################################################################################### ## ranges from 1 to 6; ##account.X.reregister_enable = 0 account.4.reregister_enable = 0 account.4.retry_counts = account.4.failback_mode = 0 account.4.failback_timeout = 3600 account.4.naptr_build = 0 account.4.fallback.redundancy_type = 0 account.4.fallback.timeout = {$yealink_outbound_proxy_fallback_interval} account.4.sip_server.1.address = account.4.sip_server.1.port = 5060 #Configure the register expiry time (in seconds), the default value is 3600. account.4.sip_server.1.expires = {$register_expires_4} account.4.sip_server.1.retry_counts = 3 account.4.sip_server.1.failback_mode = 0 account.4.sip_server.1.failback_timeout = 3600 account.4.sip_server.1.register_on_enable = 0 account.4.sip_server.2.address = account.4.sip_server.2.port = 5060 account.4.sip_server.2.expires = 3600 account.4.sip_server.2.retry_counts = 3 account.4.sip_server.2.failback_mode = 0 account.4.sip_server.2.failback_timeout = 3600 account.4.sip_server.2.register_on_enable = 0 account.4.dns_cache_type = 1 account.4.dns_cache_a.1.name = account.4.dns_cache_a.1.ip = account.4.dns_cache_a.1.ttl = 300 account.4.dns_cache_srv.1.name = account.4.dns_cache_srv.1.port = 0 account.4.dns_cache_srv.1.priority = 0 account.4.dns_cache_srv.1.target = account.4.dns_cache_srv.1.weight = 0 account.4.dns_cache_srv.1.ttl = 300 account.4.dns_cache_naptr.1.name = account.4.dns_cache_naptr.1.flags = account.4.dns_cache_naptr.1.order = 0 account.4.dns_cache_naptr.1.preference = 0 account.4.dns_cache_naptr.1.replace = account.4.dns_cache_naptr.1.service = account.4.dns_cache_naptr.1.ttl = 300 account.4.static_cache_pri = 0 ####################################################################################### ## Register Advanced ## ####################################################################################### ## ranges from 1 to 6; ##account.X.sip_server_type = #Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom; account.4.sip_server_type = #Enable or disable the phone to send the account log-off message first and then send account register message when rebooting the phone; 0-Disabled (default), 1-Enabled; account.4.unregister_on_reboot = #Enable or disable the phone to only accept the message from the server; 0-Disabled (default), 1-Enabled; account.4.sip_trust_ctrl = 1 #Configure the timeout (in seconds) for DNS query, the value ranges from 1 to 9, the default value is 8. account.4.dns_query_timeout= #Enable or disable the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled; account.4.srv_ttl_timer_enable = account.4.proxy_require = #Enable or disable the phone to send the MAC address and line number in the Register message; 0-Disabled (default), 1-Enabled; account.4.register_mac = account.4.register_line = #Configure the interval (in seconds) the phone retries to register when account1 fails to register. It ranges from 0 to 1800, the default value is 30. account.4.reg_fail_retry_interval = ######################################################################### ## NAT Settings ## ######################################################################### #Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN; account.4.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if} #Configure the STUN server address. account.4.nat.stun_server = {$stun_server} #Configure the STUN server port, the default value is 3478. account.4.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if} #Enable or disable the NAT keep-alive; 0-Disabled, 1-Default (default), 2-Option, 3-Notify; account.4.nat.udp_update_enable = 1 #Specify the keep-alive interval (in seconds), the default value is 30. account.4.nat.udp_update_time = 30 #Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled; account.4.nat.rport = {$yealink_rport} ####################################################################################### ## Account4 Advance Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.advanced.timer_t1 = 0.5 ##voice_mail.number.X = #Configure the session timer (in seconds), the default value of T1, T2, T3 is 0.5, 4, 5. account.4.advanced.timer_t1 = 0.5 account.4.advanced.timer_t2 = 4 account.4.advanced.timer_t4 = 5 voice_mail.number.4 = *97 ####################################################################################### ## Subscribe ## ####################################################################################### ## ranges from 1 to 6; ##account.X.subscribe_mwi = account.4.subscribe_mwi = 1 account.4.subscribe_mwi_expires = 3600 #Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled; account.4.subscribe_mwi_to_vm = {$yealink_subscribe_mwi_to_vm} account.4.subscribe_acd_expires= 3600 ####################################################################################### ## BLF List ## ####################################################################################### ## ranges from 1 to 6; ##account.X.blf.blf_list_uri = #Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist". account.4.blf.blf_list_uri = account.4.blf_list_code = account.4.blf_list_barge_in_code = account.4.blf.subscribe_period = 1800 account.4.blf.subscribe_event = account.4.out_dialog_blf_enable = 0 ####################################################################################### ## BLA/SCA ## ####################################################################################### ## ranges from 1 to 6; ##account.X.shared_line = #Assign account1 as shared line; 0-Disabled (default), 1-Broadsoft SCA, 2-BLA; {if isset($shared_line_4) } account.4.shared_line = {$shared_line_4} {else} account.4.shared_line = 0 {/if} #Configure BLA number for account1 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300. account.4.bla_number = account.4.bla_subscribe_period = 300 ####################################################################################### ## Audio Codec ## ####################################################################################### #Audio codecs for account1 (Y ranges from 1 to 11). #Enable or disable the specified codec; 0-Disabled, 1-Enabled; #account.4.codec.Y.enable = #The type of the specified codec. #account.4.codec.Y.payload_type = #The priority of the specified codec. It's available when the codec is enabled. #account.4.codec.Y.priority = #The payload of the specified codec. #account.4.codec.Y.rtpmap = account.4.codec.1.enable = 1 account.4.codec.1.payload_type = PCMU account.4.codec.1.priority = 1 account.4.codec.1.rtpmap = 0 account.4.codec.2.enable = 1 account.4.codec.2.payload_type = PCMA account.4.codec.2.priority = 2 account.4.codec.2.rtpmap = 8 account.4.codec.3.enable = 0 account.4.codec.3.payload_type = G723_53 account.4.codec.3.priority =0 account.4.codec.3.rtpmap = 4 account.4.codec.4.enable = 0 account.4.codec.4.payload_type = G723_63 account.4.codec.4.priority = 0 account.4.codec.4.rtpmap = 4 account.4.codec.5.enable = 1 account.4.codec.5.payload_type = G729 account.4.codec.5.priority = 3 account.4.codec.5.rtpmap = 18 account.4.codec.6.enable = 1 account.4.codec.6.payload_type = G722 account.4.codec.6.priority = 4 account.4.codec.6.rtpmap = 9 account.4.codec.7.enable = 0 account.4.codec.7.payload_type = iLBC account.4.codec.7.priority = 0 account.4.codec.7.rtpmap = 106 account.4.codec.8.enable = 0 account.4.codec.8.payload_type = G726-16 account.4.codec.8.priority = 0 account.4.codec.8.rtpmap = 103 account.4.codec.9.enable = 0 account.4.codec.9.payload_type = G726-24 account.4.codec.9.priority = 0 account.4.codec.9.rtpmap = 104 account.4.codec.10.enable = 0 account.4.codec.10.payload_type = G726-32 account.4.codec.10.priority = 0 account.4.codec.10.rtpmap = 102 account.4.codec.11.enable = 0 account.4.codec.11.payload_type = G726-40 account.4.codec.11.priority = 0 account.4.codec.11.rtpmap = 105 account.4.codec.12.enable = 0 account.4.codec.12.payload_type = GSM account.4.codec.12.priority = 0 account.4.codec.12.rtpmap = 3 ####################################################################################### ## Audio Advanced ## ####################################################################################### #Specify whether to encrypt the SIP messages; 0-Disabled (default), 1-Forced, 2-Negotiated; account.4.srtp_encryption = #Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60. account.4.ptime = ####################################################################################### ## Anonymous Call ## ####################################################################################### account.4.anonymous_call = 0 account.4.anonymous_call_oncode = account.4.anonymous_call_offcode = account.4.reject_anonymous_call = account.4.anonymous_reject_oncode = account.4.anonymous_reject_offcode = ####################################################################################### ## Pickup Code ## ####################################################################################### account.4.dialoginfo_callpickup = 0 #Configure the directed and group pickup codes for account 1, the settings on a per-account basis take precedence over the settings on the phone. account.4.group_pickup_code = account.4.direct_pickup_code = ####################################################################################### ## DTMF ## ####################################################################################### #Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO; account.4.dtmf.type = #Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event; account.4.dtmf.info_type = #Configure the RFC2833 payload. It ranges from 96 to 255, the default value is 101. account.4.dtmf.dtmf_payload = ####################################################################################### ## Alert info ## ####################################################################################### #Enable or disable to use the Distinctive Ring Tones; 0-Disabled , 1-Enabled(default); account.4.alert_info_url_enable = #Assign a ringtone for account2. The system ring tones are: common (default), Ring1.wav - Ring8.wav. #If you set the custom ring tone (Busy.wav) for the phone, the value is: account.2.ringtone.ring_type = Config:Busy.wav #If you set the system ring tone (Ring2.wav) for the phone, the value is: account.2.ringtone.ring_type = Resource:Ring2.wav account.4.ringtone.ring_type = account.4.picture_info_enable = 1 ####################################################################################### ## Conference ## ####################################################################################### #Configure the conference type; 0-Local (default), 2-Network Conference; account.4.conf_type = #Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference". account.4.conf_uri = ####################################################################################### ## cid source ## ####################################################################################### #Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM; account.4.cid_source = {$yealink_cid_source} account.4.cid_source_privacy = 1 account.4.cid_source_ppi = 1 #Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916; account.4.cp_source = 2 ####################################################################################### ## Session Timer ## ####################################################################################### #Enable or disable the session timer, 0-Disabled (default), 1-Enabled; account.4.session_timer.enable = {$yealink_session_timer} #Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999. account.4.session_timer.expires = #Configure the session timer refresher; 0-Uac (default), 1-Uas; account.4.session_timer.refresher = ####################################################################################### ## Music on Hold ## ####################################################################################### #Configure the type of Music on Hold; 0-Send the INVITE request to Music on Hold Server then hold the call; 1-Hold the call then send the INVITE request to Music on Hold Server; #Require reboot; account.4.music_on_hold_type = account.4.music_server_uri = ####################################################################################### ## Advanced ## ####################################################################################### #Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled; account.4.auto_answer = #Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default); account.4.missed_calllog = #Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled; account.4.100rel_enable = {$yealink_retransmission} #Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled; account.4.enable_user_equal_phone = #Enable or disable the simplified header field feature; 0-Disabled, 1-Enabled (default); account.4.compact_header_enable = ####################################################################################### ## DND ## ####################################################################################### account.4.dnd.enable = account.4.dnd.on_code = account.4.dnd.off_code = ####################################################################################### ## Call Forward ## ####################################################################################### #Enable or disable the busy forward feature for account; 0-Disabled (default), 1-Enabled; account.4.always_fwd.enable = account.4.always_fwd.target = account.4.always_fwd.off_code = account.4.always_fwd.on_code = account.4.busy_fwd.enable = account.4.busy_fwd.target = account.4.busy_fwd.off_code = account.4.busy_fwd.on_code = #Enable or disable the no answer forward feature for account1; 0-Disabled (default), 1-Enabled; #Configure the waiting ring times before forwarding. It ranges from 0 to 20, the default value is 2. account.4.timeout_fwd.enable = account.4.timeout_fwd.target = account.4.timeout_fwd.timeout = account.4.timeout_fwd.off_code = account.4.timeout_fwd.on_code = ####################################################################################### ## Broadsoft Hoteling ## ####################################################################################### account.4.hoteling.enable = 0 account.4.hoteling.user_id = 0 account.4.hoteling.password = 0 account.4.hoteling.auto_login_enable = 0 ####################################################################################### ## Broadsoft ACD ## ####################################################################################### account.4.acd.enable = 0 account.4.acd.unavailable_reason_enable = 0 account.4.acd.available = 0 account.4.acd.initial_state = 1 ####################################################################################### ## Broadsoft ACD Call Center ## ####################################################################################### #Configure the ACD reason code of Broadsoft.(The valus of Y must be consecutive numbers.) #account.4.bw_acd_reason_code.Y = 500(lunch time) account.4.bw_acd_reason_code.1 = account.4.reason_code.1 = account.4.reason_code_name.1 = 0 account.4.bw_disp_code.1 = account.4.bw_disp_code_name.1 = account.4.supervisor_info_code.1 = account.4.supervisor_info_code_name.1 = ####################################################################################### ## Broadsoft Call Center ## ####################################################################################### account.4.call_center.call_info_enable = 0 account.4.call_center.show_call_info_time = 30 account.4.call_center.disp_code_enable = 0 account.4.call_center.trace_enable = 0 account.4.call_center.emergency_enable = 0 account.4.call_center.queue_status_enable = 0 account.4.call_center.queue_status_light_enable = 0 ####################################################################################### ## Broadsoft XSI ## ####################################################################################### account.4.xsi.user = account.4.xsi.password = account.4.xsi.host = account.4.xsi.server_type = account.4.xsi.port = ####################################################################################### ## NETWORK ## ####################################################################################### ####################################################################################### ## Account 5 Basic Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.enable = {if isset($user_password_5) } account.5.enable = 1 {else} account.5.enable = 0 {/if} account.5.label = {$display_name_5} account.5.display_name = {$display_name_5} account.5.auth_name = {$auth_id_5} account.5.password = {$user_password_5} account.5.user_name = {$user_id_5} account.5.sip_server_host = {$server_address_5} account.5.sip_server_port = {$sip_port_5} account.5.outbound_host = {$outbound_proxy_5} account.5.outbound_port = {$sip_port_5} {if isset($yealink_sip_listen_port)}account.5.sip_listen_port = {$yealink_sip_listen_port}{else}account.5.sip_listen_port = 5060{/if} account.5.sip_listen_port = 5060 #Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV; {if $sip_transport_5 == 'udp'}account.5.transport = 0{/if} {if $sip_transport_5 == 'tcp'}account.5.transport = 1{/if} {if $sip_transport_5 == 'tls'}account.5.transport = 2{/if} {if $sip_transport_5 == 'dns srv'}account.5.transport = 3{/if} account.5.outbound_proxy.1.address = {$outbound_proxy_primary_5} account.5.outbound_proxy.2.address = {$outbound_proxy_secondary_5} account.5.outbound_proxy_enable = {if isset($outbound_proxy_primary_5)}1{else}0{/if} ####################################################################################### ## Failback ## ####################################################################################### ## ranges from 1 to 6; ##account.X.reregister_enable = 0 account.5.reregister_enable = 0 account.5.retry_counts = account.5.failback_mode = 0 account.5.failback_timeout = 3600 account.5.naptr_build = 0 account.5.fallback.redundancy_type = 0 account.5.fallback.timeout = {$yealink_outbound_proxy_fallback_interval} account.5.sip_server.1.address = account.5.sip_server.1.port = 5060 #Configure the register expiry time (in seconds), the default value is 3600. account.5.sip_server.1.expires = {$register_expires_5} account.5.sip_server.1.retry_counts = 3 account.5.sip_server.1.failback_mode = 0 account.5.sip_server.1.failback_timeout = 3600 account.5.sip_server.1.register_on_enable = 0 account.5.sip_server.2.address = account.5.sip_server.2.port = 5060 account.5.sip_server.2.expires = 3600 account.5.sip_server.2.retry_counts = 3 account.5.sip_server.2.failback_mode = 0 account.5.sip_server.2.failback_timeout = 3600 account.5.sip_server.2.register_on_enable = 0 account.5.dns_cache_type = 1 account.5.dns_cache_a.1.name = account.5.dns_cache_a.1.ip = account.5.dns_cache_a.1.ttl = 300 account.5.dns_cache_srv.1.name = account.5.dns_cache_srv.1.port = 0 account.5.dns_cache_srv.1.priority = 0 account.5.dns_cache_srv.1.target = account.5.dns_cache_srv.1.weight = 0 account.5.dns_cache_srv.1.ttl = 300 account.5.dns_cache_naptr.1.name = account.5.dns_cache_naptr.1.flags = account.5.dns_cache_naptr.1.order = 0 account.5.dns_cache_naptr.1.preference = 0 account.5.dns_cache_naptr.1.replace = account.5.dns_cache_naptr.1.service = account.5.dns_cache_naptr.1.ttl = 300 account.5.static_cache_pri = 0 ####################################################################################### ## Register Advanced ## ####################################################################################### ## ranges from 1 to 6; ##account.X.sip_server_type = #Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom; account.5.sip_server_type = #Enable or disable the phone to send the account log-off message first and then send account register message when rebooting the phone; 0-Disabled (default), 1-Enabled; account.5.unregister_on_reboot = #Enable or disable the phone to only accept the message from the server; 0-Disabled (default), 1-Enabled; account.5.sip_trust_ctrl = 1 #Configure the timeout (in seconds) for DNS query, the value ranges from 1 to 9, the default value is 8. account.5.dns_query_timeout= #Enable or disable the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled; account.5.srv_ttl_timer_enable = account.5.proxy_require = #Enable or disable the phone to send the MAC address and line number in the Register message; 0-Disabled (default), 1-Enabled; account.5.register_mac = account.5.register_line = #Configure the interval (in seconds) the phone retries to register when account1 fails to register. It ranges from 0 to 1800, the default value is 30. account.5.reg_fail_retry_interval = ######################################################################### ## NAT Settings ## ######################################################################### #Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN; account.5.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if} #Configure the STUN server address. account.5.nat.stun_server = {$stun_server} #Configure the STUN server port, the default value is 3478. account.5.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if} #Enable or disable the NAT keep-alive; 0-Disabled, 1-Default (default), 2-Option, 3-Notify; account.5.nat.udp_update_enable = 1 #Specify the keep-alive interval (in seconds), the default value is 30. account.5.nat.udp_update_time = 30 #Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled; account.5.nat.rport = {$yealink_rport} ####################################################################################### ## Account5 Advance Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.advanced.timer_t1 = 0.5 ##voice_mail.number.X = #Configure the session timer (in seconds), the default value of T1, T2, T3 is 0.5, 4, 5. account.5.advanced.timer_t1 = 0.5 account.5.advanced.timer_t2 = 4 account.5.advanced.timer_t4 = 5 voice_mail.number.5 = *97 ####################################################################################### ## Subscribe ## ####################################################################################### ## ranges from 1 to 6; ##account.X.subscribe_mwi = account.5.subscribe_mwi = 1 account.5.subscribe_mwi_expires = 3600 #Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled; account.5.subscribe_mwi_to_vm = {$yealink_subscribe_mwi_to_vm} account.5.subscribe_acd_expires= 3600 ####################################################################################### ## BLF List ## ####################################################################################### ## ranges from 1 to 6; ##account.X.blf.blf_list_uri = #Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist". account.5.blf.blf_list_uri = account.5.blf_list_code = account.5.blf_list_barge_in_code = account.5.blf.subscribe_period = 1800 account.5.blf.subscribe_event = account.5.out_dialog_blf_enable = 0 ####################################################################################### ## BLA/SCA ## ####################################################################################### ## ranges from 1 to 6; ##account.X.shared_line = #Assign account1 as shared line; 0-Disabled (default), 1-Broadsoft SCA, 2-BLA; {if isset($shared_line_5) } account.5.shared_line = {$shared_line_5} {else} account.5.shared_line = 0 {/if} #Configure BLA number for account1 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300. account.5.bla_number = account.5.bla_subscribe_period = 300 ####################################################################################### ## Audio Codec ## ####################################################################################### #Audio codecs for account1 (Y ranges from 1 to 11). #Enable or disable the specified codec; 0-Disabled, 1-Enabled; #account.5.codec.Y.enable = #The type of the specified codec. #account.5.codec.Y.payload_type = #The priority of the specified codec. It's available when the codec is enabled. #account.5.codec.Y.priority = #The payload of the specified codec. #account.5.codec.Y.rtpmap = account.5.codec.1.enable = 1 account.5.codec.1.payload_type = PCMU account.5.codec.1.priority = 1 account.5.codec.1.rtpmap = 0 account.5.codec.2.enable = 1 account.5.codec.2.payload_type = PCMA account.5.codec.2.priority = 2 account.5.codec.2.rtpmap = 8 account.5.codec.3.enable = 0 account.5.codec.3.payload_type = G723_53 account.5.codec.3.priority =0 account.5.codec.3.rtpmap = 4 account.5.codec.4.enable = 0 account.5.codec.4.payload_type = G723_63 account.5.codec.4.priority = 0 account.5.codec.4.rtpmap = 4 account.5.codec.5.enable = 1 account.5.codec.5.payload_type = G729 account.5.codec.5.priority = 3 account.5.codec.5.rtpmap = 18 account.5.codec.6.enable = 1 account.5.codec.6.payload_type = G722 account.5.codec.6.priority = 4 account.5.codec.6.rtpmap = 9 account.5.codec.7.enable = 0 account.5.codec.7.payload_type = iLBC account.5.codec.7.priority = 0 account.5.codec.7.rtpmap = 106 account.5.codec.8.enable = 0 account.5.codec.8.payload_type = G726-16 account.5.codec.8.priority = 0 account.5.codec.8.rtpmap = 103 account.5.codec.9.enable = 0 account.5.codec.9.payload_type = G726-24 account.5.codec.9.priority = 0 account.5.codec.9.rtpmap = 104 account.5.codec.10.enable = 0 account.5.codec.10.payload_type = G726-32 account.5.codec.10.priority = 0 account.5.codec.10.rtpmap = 102 account.5.codec.11.enable = 0 account.5.codec.11.payload_type = G726-40 account.5.codec.11.priority = 0 account.5.codec.11.rtpmap = 105 account.5.codec.12.enable = 0 account.5.codec.12.payload_type = GSM account.5.codec.12.priority = 0 account.5.codec.12.rtpmap = 3 ####################################################################################### ## Audio Advanced ## ####################################################################################### #Specify whether to encrypt the SIP messages; 0-Disabled (default), 1-Forced, 2-Negotiated; account.5.srtp_encryption = #Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60. account.5.ptime = ####################################################################################### ## Anonymous Call ## ####################################################################################### account.5.anonymous_call = 0 account.5.anonymous_call_oncode = account.5.anonymous_call_offcode = account.5.reject_anonymous_call = account.5.anonymous_reject_oncode = account.5.anonymous_reject_offcode = ####################################################################################### ## Pickup Code ## ####################################################################################### account.5.dialoginfo_callpickup = 0 #Configure the directed and group pickup codes for account 1, the settings on a per-account basis take precedence over the settings on the phone. account.5.group_pickup_code = account.5.direct_pickup_code = ####################################################################################### ## DTMF ## ####################################################################################### #Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO; account.5.dtmf.type = #Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event; account.5.dtmf.info_type = #Configure the RFC2833 payload. It ranges from 96 to 255, the default value is 101. account.5.dtmf.dtmf_payload = ####################################################################################### ## Alert info ## ####################################################################################### #Enable or disable to use the Distinctive Ring Tones; 0-Disabled , 1-Enabled(default); account.5.alert_info_url_enable = #Assign a ringtone for account2. The system ring tones are: common (default), Ring1.wav - Ring8.wav. #If you set the custom ring tone (Busy.wav) for the phone, the value is: account.2.ringtone.ring_type = Config:Busy.wav #If you set the system ring tone (Ring2.wav) for the phone, the value is: account.2.ringtone.ring_type = Resource:Ring2.wav account.5.ringtone.ring_type = account.5.picture_info_enable = 1 ####################################################################################### ## Conference ## ####################################################################################### #Configure the conference type; 0-Local (default), 2-Network Conference; account.5.conf_type = #Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference". account.5.conf_uri = ####################################################################################### ## cid source ## ####################################################################################### #Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM; account.5.cid_source = {$yealink_cid_source} account.5.cid_source_privacy = 1 account.5.cid_source_ppi = 1 #Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916; account.5.cp_source = 2 ####################################################################################### ## Session Timer ## ####################################################################################### #Enable or disable the session timer, 0-Disabled (default), 1-Enabled; account.5.session_timer.enable = {$yealink_session_timer} #Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999. account.5.session_timer.expires = #Configure the session timer refresher; 0-Uac (default), 1-Uas; account.5.session_timer.refresher = ####################################################################################### ## Music on Hold ## ####################################################################################### #Configure the type of Music on Hold; 0-Send the INVITE request to Music on Hold Server then hold the call; 1-Hold the call then send the INVITE request to Music on Hold Server; #Require reboot; account.5.music_on_hold_type = account.5.music_server_uri = ####################################################################################### ## Advanced ## ####################################################################################### #Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled; account.5.auto_answer = #Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default); account.5.missed_calllog = #Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled; account.5.100rel_enable = {$yealink_retransmission} #Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled; account.5.enable_user_equal_phone = #Enable or disable the simplified header field feature; 0-Disabled, 1-Enabled (default); account.5.compact_header_enable = ####################################################################################### ## DND ## ####################################################################################### account.5.dnd.enable = account.5.dnd.on_code = account.5.dnd.off_code = ####################################################################################### ## Call Forward ## ####################################################################################### #Enable or disable the busy forward feature for account; 0-Disabled (default), 1-Enabled; account.5.always_fwd.enable = account.5.always_fwd.target = account.5.always_fwd.off_code = account.5.always_fwd.on_code = account.5.busy_fwd.enable = account.5.busy_fwd.target = account.5.busy_fwd.off_code = account.5.busy_fwd.on_code = #Enable or disable the no answer forward feature for account1; 0-Disabled (default), 1-Enabled; #Configure the waiting ring times before forwarding. It ranges from 0 to 20, the default value is 2. account.5.timeout_fwd.enable = account.5.timeout_fwd.target = account.5.timeout_fwd.timeout = account.5.timeout_fwd.off_code = account.5.timeout_fwd.on_code = ####################################################################################### ## Broadsoft Hoteling ## ####################################################################################### account.5.hoteling.enable = 0 account.5.hoteling.user_id = 0 account.5.hoteling.password = 0 account.5.hoteling.auto_login_enable = 0 ####################################################################################### ## Broadsoft ACD ## ####################################################################################### account.5.acd.enable = 0 account.5.acd.unavailable_reason_enable = 0 account.5.acd.available = 0 account.5.acd.initial_state = 1 ####################################################################################### ## Broadsoft ACD Call Center ## ####################################################################################### #Configure the ACD reason code of Broadsoft.(The valus of Y must be consecutive numbers.) #account.5.bw_acd_reason_code.Y = 500(lunch time) account.5.bw_acd_reason_code.1 = account.5.reason_code.1 = account.5.reason_code_name.1 = 0 account.5.bw_disp_code.1 = account.5.bw_disp_code_name.1 = account.5.supervisor_info_code.1 = account.5.supervisor_info_code_name.1 = ####################################################################################### ## Broadsoft Call Center ## ####################################################################################### account.5.call_center.call_info_enable = 0 account.5.call_center.show_call_info_time = 30 account.5.call_center.disp_code_enable = 0 account.5.call_center.trace_enable = 0 account.5.call_center.emergency_enable = 0 account.5.call_center.queue_status_enable = 0 account.5.call_center.queue_status_light_enable = 0 ####################################################################################### ## Broadsoft XSI ## ####################################################################################### account.5.xsi.user = account.5.xsi.password = account.5.xsi.host = account.5.xsi.server_type = account.5.xsi.port = ####################################################################################### ## NETWORK ## ####################################################################################### ####################################################################################### ## Account 6 Basic Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.enable = {if isset($user_password_6) } account.6.enable = 1 {else} account.6.enable = 0 {/if} account.6.label = {$display_name_6} account.6.display_name = {$display_name_6} account.6.auth_name = {$auth_id_6} account.6.password = {$user_password_6} account.6.user_name = {$user_id_6} account.6.sip_server_host = {$server_address_6} account.6.sip_server_port = {$sip_port_6} account.6.outbound_host = {$outbound_proxy_6} account.6.outbound_port = {$sip_port_6} {if isset($yealink_sip_listen_port)}account.6.sip_listen_port = {$yealink_sip_listen_port}{else}account.6.sip_listen_port = 5060{/if} account.6.sip_listen_port = 5060 #Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV; {if $sip_transport_6 == 'udp'}account.6.transport = 0{/if} {if $sip_transport_6 == 'tcp'}account.6.transport = 1{/if} {if $sip_transport_6 == 'tls'}account.6.transport = 2{/if} {if $sip_transport_6 == 'dns srv'}account.6.transport = 3{/if} account.6.outbound_proxy.1.address = {$outbound_proxy_primary_6} account.6.outbound_proxy.2.address = {$outbound_proxy_secondary_6} account.6.outbound_proxy_enable = {if isset($outbound_proxy_primary_6)}1{else}0{/if} ####################################################################################### ## Failback ## ####################################################################################### ## ranges from 1 to 6; ##account.X.reregister_enable = 0 account.6.reregister_enable = 0 account.6.retry_counts = account.6.failback_mode = 0 account.6.failback_timeout = 3600 account.6.naptr_build = 0 account.6.fallback.redundancy_type = 0 account.6.fallback.timeout = {$yealink_outbound_proxy_fallback_interval} account.6.sip_server.1.address = account.6.sip_server.1.port = 5060 #Configure the register expiry time (in seconds), the default value is 3600. account.6.sip_server.1.expires = {$register_expires_6} account.6.sip_server.1.retry_counts = 3 account.6.sip_server.1.failback_mode = 0 account.6.sip_server.1.failback_timeout = 3600 account.6.sip_server.1.register_on_enable = 0 account.6.sip_server.2.address = account.6.sip_server.2.port = 5060 account.6.sip_server.2.expires = 3600 account.6.sip_server.2.retry_counts = 3 account.6.sip_server.2.failback_mode = 0 account.6.sip_server.2.failback_timeout = 3600 account.6.sip_server.2.register_on_enable = 0 account.6.dns_cache_type = 1 account.6.dns_cache_a.1.name = account.6.dns_cache_a.1.ip = account.6.dns_cache_a.1.ttl = 300 account.6.dns_cache_srv.1.name = account.6.dns_cache_srv.1.port = 0 account.6.dns_cache_srv.1.priority = 0 account.6.dns_cache_srv.1.target = account.6.dns_cache_srv.1.weight = 0 account.6.dns_cache_srv.1.ttl = 300 account.6.dns_cache_naptr.1.name = account.6.dns_cache_naptr.1.flags = account.6.dns_cache_naptr.1.order = 0 account.6.dns_cache_naptr.1.preference = 0 account.6.dns_cache_naptr.1.replace = account.6.dns_cache_naptr.1.service = account.6.dns_cache_naptr.1.ttl = 300 account.6.static_cache_pri = 0 ####################################################################################### ## Register Advanced ## ####################################################################################### ## ranges from 1 to 6; ##account.X.sip_server_type = #Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom; account.6.sip_server_type = #Enable or disable the phone to send the account log-off message first and then send account register message when rebooting the phone; 0-Disabled (default), 1-Enabled; account.6.unregister_on_reboot = #Enable or disable the phone to only accept the message from the server; 0-Disabled (default), 1-Enabled; account.6.sip_trust_ctrl = 1 #Configure the timeout (in seconds) for DNS query, the value ranges from 1 to 9, the default value is 8. account.6.dns_query_timeout= #Enable or disable the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled; account.6.srv_ttl_timer_enable = account.6.proxy_require = #Enable or disable the phone to send the MAC address and line number in the Register message; 0-Disabled (default), 1-Enabled; account.6.register_mac = account.6.register_line = #Configure the interval (in seconds) the phone retries to register when account1 fails to register. It ranges from 0 to 1800, the default value is 30. account.6.reg_fail_retry_interval = ######################################################################### ## NAT Settings ## ######################################################################### ## ranges from 1 to 6; ##account.X.nat.nat_traversal = 0 #Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN; account.6.nat.nat_traversal = 0 account.6.nat.stun_server = account.6.nat.stun_port = 3478 #Enable or disable the NAT keep-alive; 0-Disabled, 1-Default (default), 2-Option, 3-Notify; account.6.nat.udp_update_enable = 1 #Specify the keep-alive interval (in seconds), the default value is 30. account.6.nat.udp_update_time = 30 #Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled; account.6.nat.rport = {$yealink_rport} ####################################################################################### ## Account6 Advance Settings ## ####################################################################################### ## ranges from 1 to 6; ##account.X.advanced.timer_t1 = 0.5 ##voice_mail.number.X = #Configure the session timer (in seconds), the default value of T1, T2, T3 is 0.5, 4, 5. account.6.advanced.timer_t1 = 0.5 account.6.advanced.timer_t2 = 4 account.6.advanced.timer_t4 = 5 voice_mail.number.6 = *97 ####################################################################################### ## Subscribe ## ####################################################################################### ## ranges from 1 to 6; ##account.X.subscribe_mwi = account.6.subscribe_mwi = 0 account.6.subscribe_mwi_expires = 3600 #Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled; account.6.subscribe_mwi_to_vm = {$yealink_subscribe_mwi_to_vm} account.6.subscribe_acd_expires= 3600 ####################################################################################### ## BLF List ## ####################################################################################### ## ranges from 1 to 6; ##account.X.blf.blf_list_uri = #Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist". account.6.blf.blf_list_uri = account.6.blf_list_code = account.6.blf_list_barge_in_code = account.6.blf.subscribe_period = 1800 account.6.blf.subscribe_event = account.6.out_dialog_blf_enable = 0 ####################################################################################### ## BLA/SCA ## ####################################################################################### ## ranges from 1 to 6; ##account.X.shared_line = #Assign account1 as shared line; 0-Disabled (default), 1-Broadsoft SCA, 2-BLA; {if isset($shared_line_6) } account.6.shared_line = {$shared_line_6} {else} account.6.shared_line = 0 {/if} #Configure BLA number for account1 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300. account.6.bla_number = account.6.bla_subscribe_period = 300 ####################################################################################### ## Audio Codec ## ####################################################################################### #Audio codecs for account1 (Y ranges from 1 to 11). #Enable or disable the specified codec; 0-Disabled, 1-Enabled; #account.6.codec.Y.enable = #The type of the specified codec. #account.6.codec.Y.payload_type = #The priority of the specified codec. It's available when the codec is enabled. #account.6.codec.Y.priority = #The payload of the specified codec. #account.6.codec.Y.rtpmap = account.6.codec.1.enable = 1 account.6.codec.1.payload_type = PCMU account.6.codec.1.priority = 1 account.6.codec.1.rtpmap = 0 account.6.codec.2.enable = 1 account.6.codec.2.payload_type = PCMA account.6.codec.2.priority = 2 account.6.codec.2.rtpmap = 8 account.6.codec.3.enable = 0 account.6.codec.3.payload_type = G723_53 account.6.codec.3.priority =0 account.6.codec.3.rtpmap = 4 account.6.codec.4.enable = 0 account.6.codec.4.payload_type = G723_63 account.6.codec.4.priority = 0 account.6.codec.4.rtpmap = 4 account.6.codec.5.enable = 1 account.6.codec.5.payload_type = G729 account.6.codec.5.priority = 3 account.6.codec.5.rtpmap = 18 account.6.codec.6.enable = 1 account.6.codec.6.payload_type = G722 account.6.codec.6.priority = 4 account.6.codec.6.rtpmap = 9 account.6.codec.7.enable = 0 account.6.codec.7.payload_type = iLBC account.6.codec.7.priority = 0 account.6.codec.7.rtpmap = 106 account.6.codec.8.enable = 0 account.6.codec.8.payload_type = G726-16 account.6.codec.8.priority = 0 account.6.codec.8.rtpmap = 103 account.6.codec.9.enable = 0 account.6.codec.9.payload_type = G726-24 account.6.codec.9.priority = 0 account.6.codec.9.rtpmap = 104 account.6.codec.10.enable = 0 account.6.codec.10.payload_type = G726-32 account.6.codec.10.priority = 0 account.6.codec.10.rtpmap = 102 account.6.codec.11.enable = 0 account.6.codec.11.payload_type = G726-40 account.6.codec.11.priority = 0 account.6.codec.11.rtpmap = 105 account.6.codec.12.enable = 0 account.6.codec.12.payload_type = GSM account.6.codec.12.priority = 0 account.6.codec.12.rtpmap = 3 ####################################################################################### ## Audio Advanced ## ####################################################################################### #Specify whether to encrypt the SIP messages; 0-Disabled (default), 1-Forced, 2-Negotiated; account.6.srtp_encryption = #Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60. account.6.ptime = ####################################################################################### ## Anonymous Call ## ####################################################################################### account.6.anonymous_call = 0 account.6.anonymous_call_oncode = account.6.anonymous_call_offcode = account.6.reject_anonymous_call = account.6.anonymous_reject_oncode = account.6.anonymous_reject_offcode = ####################################################################################### ## Pickup Code ## ####################################################################################### account.5.dialoginfo_callpickup = 0 #Configure the directed and group pickup codes for account 1, the settings on a per-account basis take precedence over the settings on the phone. account.6.group_pickup_code = account.56.direct_pickup_code = ####################################################################################### ## DTMF ## ####################################################################################### #Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO; account.6.dtmf.type = #Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event; account.6.dtmf.info_type = #Configure the RFC2833 payload. It ranges from 96 to 255, the default value is 101. account.6.dtmf.dtmf_payload = ####################################################################################### ## Alert info ## ####################################################################################### #Enable or disable to use the Distinctive Ring Tones; 0-Disabled , 1-Enabled(default); account.6.alert_info_url_enable = #Assign a ringtone for account2. The system ring tones are: common (default), Ring1.wav - Ring8.wav. #If you set the custom ring tone (Busy.wav) for the phone, the value is: account.2.ringtone.ring_type = Config:Busy.wav #If you set the system ring tone (Ring2.wav) for the phone, the value is: account.2.ringtone.ring_type = Resource:Ring2.wav account.6.ringtone.ring_type = account.6.picture_info_enable = 1 ####################################################################################### ## Conference ## ####################################################################################### #Configure the conference type; 0-Local (default), 2-Network Conference; account.6.conf_type = #Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference". account.6.conf_uri = ####################################################################################### ## cid source ## ####################################################################################### #Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM; account.6.cid_source = {$yealink_cid_source} account.6.cid_source_privacy = 1 account.6.cid_source_ppi = 1 #Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916; account.6.cp_source = 2 ####################################################################################### ## Session Timer ## ####################################################################################### #Enable or disable the session timer, 0-Disabled (default), 1-Enabled; account.6.session_timer.enable = {$yealink_session_timer} #Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999. account.6.session_timer.expires = #Configure the session timer refresher; 0-Uac (default), 1-Uas; account.6.session_timer.refresher = ####################################################################################### ## Music on Hold ## ####################################################################################### #Configure the type of Music on Hold; 0-Send the INVITE request to Music on Hold Server then hold the call; 1-Hold the call then send the INVITE request to Music on Hold Server; #Require reboot; account.6.music_on_hold_type = account.6.music_server_uri = ####################################################################################### ## Advanced ## ####################################################################################### #Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled; account.6.auto_answer = #Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default); account.6.missed_calllog = #Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled; account.6.100rel_enable = {$yealink_retransmission} #Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled; account.6.enable_user_equal_phone = #Enable or disable the simplified header field feature; 0-Disabled, 1-Enabled (default); account.6.compact_header_enable = ####################################################################################### ## DND ## ####################################################################################### account.6.dnd.enable = account.6.dnd.on_code = account.6.dnd.off_code = ####################################################################################### ## Call Forward ## ####################################################################################### #Enable or disable the busy forward feature for account; 0-Disabled (default), 1-Enabled; account.6.always_fwd.enable = account.6.always_fwd.target = account.6.always_fwd.off_code = account.6.always_fwd.on_code = account.6.busy_fwd.enable = account.6.busy_fwd.target = account.6.busy_fwd.off_code = account.6.busy_fwd.on_code = #Enable or disable the no answer forward feature for account1; 0-Disabled (default), 1-Enabled; #Configure the waiting ring times before forwarding. It ranges from 0 to 20, the default value is 2. account.6.timeout_fwd.enable = account.6.timeout_fwd.target = account.6.timeout_fwd.timeout = account.6.timeout_fwd.off_code = account.6.timeout_fwd.on_code = ####################################################################################### ## Broadsoft Hoteling ## ####################################################################################### account.6.hoteling.enable = 0 account.6.hoteling.user_id = 0 account.6.hoteling.password = 0 account.6.hoteling.auto_login_enable = 0 ####################################################################################### ## Broadsoft ACD ## ####################################################################################### account.6.acd.enable = 0 account.6.acd.unavailable_reason_enable = 0 account.6.acd.available = 0 account.6.acd.initial_state = 1 ####################################################################################### ## Broadsoft ACD Call Center ## ####################################################################################### #Configure the ACD reason code of Broadsoft.(The valus of Y must be consecutive numbers.) #account.6.bw_acd_reason_code.Y = 500(lunch time) account.6.bw_acd_reason_code.1 = account.6.reason_code.1 = account.6.reason_code_name.1 = 0 account.6.bw_disp_code.1 = account.6.bw_disp_code_name.1 = account.6.supervisor_info_code.1 = account.6.supervisor_info_code_name.1 = ####################################################################################### ## Broadsoft Call Center ## ####################################################################################### account.6.call_center.call_info_enable = 0 account.6.call_center.show_call_info_time = 30 account.6.call_center.disp_code_enable = 0 account.6.call_center.trace_enable = 0 account.6.call_center.emergency_enable = 0 account.6.call_center.queue_status_enable = 0 account.6.call_center.queue_status_light_enable = 0 ####################################################################################### ## Broadsoft XSI ## ####################################################################################### account.6.xsi.user = account.6.xsi.password = account.6.xsi.host = account.6.xsi.server_type = account.6.xsi.port = ####################################################################################### ## NETWORK ## ####################################################################################### ####################################################################################### ## Line Key ## ####################################################################################### #The x of the parameter "linekey.x.line" ranges from 1 to 6. #The default value equals to the value of x. For example, the default value of the parameter "linekey.1.line" is 1. #linekey.x.lable--Define the label for each line key. Meet-Me Conference "1" or BLF "16" require pick_value. {foreach $keys['line'] as $row} #Configure Line Key {$row.device_key_id} linekey.{$row.device_key_id}.line = {$row.device_key_line} linekey.{$row.device_key_id}.value = {$row.device_key_value} {if $row.device_key_type == "1" || $row.device_key_type == "16"} linekey.{$row.device_key_id}.pickup_value = {$row.device_key_extension} {else} linekey.{$row.device_key_id}.extension = {$row.device_key_extension} {/if} linekey.{$row.device_key_id}.type = {$row.device_key_type} linekey.{$row.device_key_id}.xml_phonebook = linekey.{$row.device_key_id}.label = {$row.device_key_label} {/foreach} ####################################################################################### ## Memory Key (For T38G only) ## ####################################################################################### #X ranges from 1 to 10; #memorykey.x.line--Configure the desired line to apply the key feature. It ranges from 0 to 6. #The value 0 of the "memorykey.x.line" stands for Auto, it means the first available line. #But, when the DSS key is configured as BLF, BLF List, Shared Line, Call Park, Pick Up, ACD or Voice Mail feature, the value 0 stands for line 1. #memorykey.x.value--Enter the value of some features. E.g. When configuring the DSS key to be BLF, enter the number of the monitored user. #memorykey.x.extension--Enter the pickup code, this parameter is only appilicable to BLF. #memorykey.x.type--Assign the desired feature to the memory key. #Valid types are: 0-N/A(default for memory key) 1-Conference 2-Forward 3-Transfer 4-Hold 5-DND 6-Redial 7-Call Return 8-SMS # 9-Call Pickup 10-Call Park 11-DTMF 12-Voicemail 13-SpeedDial 14-Intercom 15-Line(default for line key) 16-BLF 17-URL # 18-Group Listening 19-Public Hold 20-Private 21-Shared Line 22-XML Group 23-Group Pickup 24-Paging 25-Record 27-XML Browser # 34-Hot Desking 35-URL Record 38-LDAP 39-BLF List 40-Prefix 41-Zero-Sp-Touch 42-ACD 45-Local Group 46-Broadsoft Group #memorykey.x.xml_phonebook--Specify the desired remote phonebook/local group/BSFT phonebook for the DSS key. This parameter is only appilicable to the feature XML Group/Local Group/Broadsoft Group. #memorykey.x.sub_type = {foreach $keys["memory"] as $row} #Expansion Memory Key {$row.device_key_id} memorykey.{$row.device_key_id}.type = {$row.device_key_type} memorykey.{$row.device_key_id}.line = {$row.device_key_line} memorykey.{$row.device_key_id}.value = {$row.device_key_value} memorykey.{$row.device_key_id}.extension = {$row.device_key_extension} memorykey.{$row.device_key_id}.label = {$row.device_key_label} memorykey.{$row.device_key_id}.xml_phonebook = memorykey.{$row.device_key_id}.sub_type = {/foreach} ########################################################################################## ## Programmable Key (For T38G only) ## ########################################################################################## #X ranges from 1 to 15. #programablekey.x.type--Customize the programmable key type. #The valid types are: #0-N/A 2-Forward 5-DND 6-Redial 7-Call Return 8-SMS 9-Call Pickup 13-Spead Dial 14-Intercom #22-XML Group 23-Group Pickup 27-XML Browser 28-History 29-Directory 30-Menu 32-New SMS 33-Status 43-Local Phonebook #44-Broadsoft Phonebook 45-Local Group 46-Broadsoft Group 47-XML Phonebook 48-Switch Account Up 49-Switch Account Down 50-Keypad Lock #programablekey.x.line--Configure the desired line to apply the key feature. It ranges from 0 to 6. #The value 0 of the "proramablekey.x.line" stands for Auto, it means the first available line. #But, when the programmable key is configured as Pick Up, the value 0 stands for line 1. {foreach $keys["programmable"] as $row} programablekey.{$row.device_key_id}.type = {$row.device_key_type} programablekey.{$row.device_key_id}.line = {$row.device_key_line} programablekey.{$row.device_key_id}.value = {$row.device_key_value} programablekey.{$row.device_key_id}.xml_phonebook = programablekey.{$row.device_key_id}.history_type = programablekey.{$row.device_key_id}.label = {$row.device_key_label} {/foreach} #programablekey.x.value = #programablekey.x.xml_phonebook--Specify the desired remote phonebook/local group/BSFT phonebook for the programmable key. This parameter is only appilicable to the feature XML Group/Local Group/Broadsoft Group. #programablekey.x.history_type = #programablekey.x.label--This parameter is only available to the key 1 to key 4. #History #programablekey.1.type = 28 #programablekey.1.line = 1 #programablekey.1.value = #programablekey.1.xml_phonebook = #programablekey.1.history_type = #programablekey.1.label = #Directory #programablekey.2.type = 29 #programablekey.2.line = 1 #programablekey.2.value = #programablekey.2.xml_phonebook = #programablekey.2.history_type = #programablekey.2.label = #DND programablekey.3.type = 5 programablekey.3.line = 1 programablekey.3.value = programablekey.3.xml_phonebook = programablekey.3.history_type = programablekey.3.label = #Menu #programablekey.4.type = 30 #programablekey.4.line = #programablekey.4.value = #programablekey.4.xml_phonebook = #programablekey.4.history_type = #programablekey.4.label = ########################################################################################## ## Expansion Module 1 ## ########################################################################################## #X ranges from 1 to 16, Y ranges from 1 to 40. #expansion_module.x.key.y.type = 37 (Switch by default) #expansion_module.x.key.y.line = 0 #expansion_module.x.key.y.value = #expansion_module.x.key.y.extension = #expansion_module.x.key.y.label = #expansion_module.X.key.Y.xml_phonebook = {$rownum = 1} {foreach $keys["expansion"] as $row} {if $rownum <= 40} expansion_module.1.key.{$row.device_key_id}.type = {$row.device_key_type} expansion_module.1.key.{$row.device_key_id}.line = {$row.device_key_line} expansion_module.1.key.{$row.device_key_id}.value = {$row.device_key_value} expansion_module.1.key.{$row.device_key_id}.extension = {$row.device_key_extension} expansion_module.1.key.{$row.device_key_id}.label = {$row.device_key_label} expansion_module.1.key.{$row.device_key_id}.xml_phonebook = {else} expansion_module.2.key.{$row.device_key_id - 40}.type = {$row.device_key_type} expansion_module.2.key.{$row.device_key_id - 40}.line = {$row.device_key_line} expansion_module.2.key.{$row.device_key_id - 40}.value = {$row.device_key_value} expansion_module.2.key.{$row.device_key_id - 40}.extension = {$row.device_key_extension} expansion_module.2.key.{$row.device_key_id - 40}.label = {$row.device_key_label} expansion_module.2.key.{$row.device_key_id - 40}.xml_phonebook = {/if} {$rownum = $rownum + 1} {/foreach} ########################################################################################## ## Expansion Module 2 ## ########################################################################################## #Expansion module 2 key 1 #expansion_module.2.key.1.type = #expansion_module.2.key.1.line = #expansion_module.2.key.1.value = #expansion_module.2.key.1.extension = #expansion_module.2.key.1.label = #expansion_module.2.key.1.xml_phonebook = #expansion_module.2.key.1.type = #expansion_module.2.key.1.label =