1 /* $OpenBSD: icsphyreg.h,v 1.3 2008/06/26 05:42:16 ray Exp $ */ 2 /* $NetBSD: icsphyreg.h,v 1.1 1998/11/02 23:46:20 thorpej Exp $ */ 3 4 /*- 5 * Copyright (c) 1998 The NetBSD Foundation, Inc. 6 * All rights reserved. 7 * 8 * This code is derived from software contributed to The NetBSD Foundation 9 * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility, 10 * NASA Ames Research Center. 11 * 12 * Redistribution and use in source and binary forms, with or without 13 * modification, are permitted provided that the following conditions 14 * are met: 15 * 1. Redistributions of source code must retain the above copyright 16 * notice, this list of conditions and the following disclaimer. 17 * 2. Redistributions in binary form must reproduce the above copyright 18 * notice, this list of conditions and the following disclaimer in the 19 * documentation and/or other materials provided with the distribution. 20 * 21 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS 22 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 23 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 24 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS 25 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 26 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 27 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 28 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 29 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 30 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 31 * POSSIBILITY OF SUCH DAMAGE. 32 */ 33 34 #ifndef _DEV_MII_ICSPHYREG_H_ 35 #define _DEV_MII_ICSPHYREG_H_ 36 37 /* 38 * Register definitions for the ICS1890 Ethernet PHY 39 * Further documentation can be found at: 40 * http://www.icst.com/products/pinfo/1890.htm 41 */ 42 43 #define MII_ICSPHY_ECR 0x10 /* Extended Control Register */ 44 #define ECR_OVR 0x8000 /* disable command reg overwrites */ 45 #define ECR_PHYADDR_MASK 0x07c0 /* PHY address mask */ 46 #define ECR_CTEST 0x0020 /* Stream Cipher Test Mode */ 47 #define ECR_IECT 0x0004 /* Invalid Error Code Test */ 48 #define ECR_SSD 0x0001 /* Stream Cipher Disable */ 49 50 #define MII_ICSPHY_QPR 0x11 /* Quick Poll Register */ 51 #define QPR_SPEED 0x8000 /* 100Mbps */ 52 #define QPR_FDX 0x4000 /* Full dupled */ 53 #define QPR_ANB2 0x2000 /* Autoneg monitor bit 2 */ 54 #define QPR_ANB1 0x1000 /* Autoneg monitor bit 1 */ 55 #define QPR_ANB0 0x0800 /* Autoneg monitor bit 0 */ 56 #define QPR_RXERR 0x0400 /* Receive signal lost */ 57 #define QPR_PLLERR 0x0200 /* PLL error */ 58 #define QPR_FCARR 0x0100 /* False carrier detected */ 59 #define QPR_INVALSYM 0x0080 /* Invalid Symbol Detected */ 60 #define QPR_HALT 0x0040 /* Halt Symbol Detected */ 61 #define QPR_PREEM 0x0020 /* Two Idle Symbols together */ 62 #define QPR_ACOMP 0x0010 /* Autonegotiation complete */ 63 #define QPR_JABBER 0x0004 /* Jabber detected */ 64 #define QPR_RFAULT 0x0002 /* Remote Fault */ 65 #define QPR_LINK 0x0001 /* Link */ 66 67 #define MII_ICSPHY_TTR 0x12 /* 10baseT Operations Register */ 68 #define TTR_RJABBER 0x8000 /* Remote Jabber */ 69 #define TTR_POLARITY 0x4000 /* Polarity Reversed */ 70 #define TTR_NOJABBER 0x0020 /* Disable Jabber Check */ 71 #define TTR_LOOP 0x0010 /* Loopback mode */ 72 #define TTR_NOAPOLARITY 0x0008 /* Disable auto polarity correction */ 73 #define TTR_NOSQE 0x0004 /* Disable SQE check */ 74 #define TTR_NOLINK 0x0002 /* Disable Link check */ 75 #define TTR_NOSQUELCH 0x0001 /* Disable squelch */ 76 77 #define MII_ICSPHY_ECR2 0x13 /* Extended Control Register 2 */ 78 #define ECR2_REPEATER 0x8000 /* Repeater Mode */ 79 #define ECR2_HWSW 0x4000 /* hw/sw config priority */ 80 #define ECR2_LPRF 0x2000 /* link partner supports rem fault */ 81 #define ECR2_FORCERF 0x0400 /* Force transmit of rem fault */ 82 #define ECR2_RFPUP 0x0010 /* Rem fault on power up */ 83 #define ECR2_Q10T 0x0004 /* Qualified 10baseT data */ 84 #define ECR2_10TPROT 0x0002 /* 10baseT protect */ 85 #define ECR2_AUTOPWRDN 0x0001 /* automatic power down */ 86 87 #endif /* _DEV_MII_ICSPHYREG_H_ */ 88