xref: /linux/include/uapi/linux/mii.h (revision bdbdac76)
1 /* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
2 /*
3  * linux/mii.h: definitions for MII-compatible transceivers
4  * Originally drivers/net/sunhme.h.
5  *
6  * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com)
7  */
8 
9 #ifndef _UAPI__LINUX_MII_H__
10 #define _UAPI__LINUX_MII_H__
11 
12 #include <linux/types.h>
13 #include <linux/ethtool.h>
14 
15 /* Generic MII registers. */
16 #define MII_BMCR		0x00	/* Basic mode control register */
17 #define MII_BMSR		0x01	/* Basic mode status register  */
18 #define MII_PHYSID1		0x02	/* PHYS ID 1                   */
19 #define MII_PHYSID2		0x03	/* PHYS ID 2                   */
20 #define MII_ADVERTISE		0x04	/* Advertisement control reg   */
21 #define MII_LPA			0x05	/* Link partner ability reg    */
22 #define MII_EXPANSION		0x06	/* Expansion register          */
23 #define MII_CTRL1000		0x09	/* 1000BASE-T control          */
24 #define MII_STAT1000		0x0a	/* 1000BASE-T status           */
25 #define	MII_MMD_CTRL		0x0d	/* MMD Access Control Register */
26 #define	MII_MMD_DATA		0x0e	/* MMD Access Data Register */
27 #define MII_ESTATUS		0x0f	/* Extended Status             */
28 #define MII_DCOUNTER		0x12	/* Disconnect counter          */
29 #define MII_FCSCOUNTER		0x13	/* False carrier counter       */
30 #define MII_NWAYTEST		0x14	/* N-way auto-neg test reg     */
31 #define MII_RERRCOUNTER		0x15	/* Receive error counter       */
32 #define MII_SREVISION		0x16	/* Silicon revision            */
33 #define MII_RESV1		0x17	/* Reserved...                 */
34 #define MII_LBRERROR		0x18	/* Lpback, rx, bypass error    */
35 #define MII_PHYADDR		0x19	/* PHY address                 */
36 #define MII_RESV2		0x1a	/* Reserved...                 */
37 #define MII_TPISTATUS		0x1b	/* TPI status for 10mbps       */
38 #define MII_NCONFIG		0x1c	/* Network interface config    */
39 
40 /* Basic mode control register. */
41 #define BMCR_RESV		0x003f	/* Unused...                   */
42 #define BMCR_SPEED1000		0x0040	/* MSB of Speed (1000)         */
43 #define BMCR_CTST		0x0080	/* Collision test              */
44 #define BMCR_FULLDPLX		0x0100	/* Full duplex                 */
45 #define BMCR_ANRESTART		0x0200	/* Auto negotiation restart    */
46 #define BMCR_ISOLATE		0x0400	/* Isolate data paths from MII */
47 #define BMCR_PDOWN		0x0800	/* Enable low power state      */
48 #define BMCR_ANENABLE		0x1000	/* Enable auto negotiation     */
49 #define BMCR_SPEED100		0x2000	/* Select 100Mbps              */
50 #define BMCR_LOOPBACK		0x4000	/* TXD loopback bits           */
51 #define BMCR_RESET		0x8000	/* Reset to default state      */
52 #define BMCR_SPEED10		0x0000	/* Select 10Mbps               */
53 
54 /* Basic mode status register. */
55 #define BMSR_ERCAP		0x0001	/* Ext-reg capability          */
56 #define BMSR_JCD		0x0002	/* Jabber detected             */
57 #define BMSR_LSTATUS		0x0004	/* Link status                 */
58 #define BMSR_ANEGCAPABLE	0x0008	/* Able to do auto-negotiation */
59 #define BMSR_RFAULT		0x0010	/* Remote fault detected       */
60 #define BMSR_ANEGCOMPLETE	0x0020	/* Auto-negotiation complete   */
61 #define BMSR_RESV		0x00c0	/* Unused...                   */
62 #define BMSR_ESTATEN		0x0100	/* Extended Status in R15      */
63 #define BMSR_100HALF2		0x0200	/* Can do 100BASE-T2 HDX       */
64 #define BMSR_100FULL2		0x0400	/* Can do 100BASE-T2 FDX       */
65 #define BMSR_10HALF		0x0800	/* Can do 10mbps, half-duplex  */
66 #define BMSR_10FULL		0x1000	/* Can do 10mbps, full-duplex  */
67 #define BMSR_100HALF		0x2000	/* Can do 100mbps, half-duplex */
68 #define BMSR_100FULL		0x4000	/* Can do 100mbps, full-duplex */
69 #define BMSR_100BASE4		0x8000	/* Can do 100mbps, 4k packets  */
70 
71 /* Advertisement control register. */
72 #define ADVERTISE_SLCT		0x001f	/* Selector bits               */
73 #define ADVERTISE_CSMA		0x0001	/* Only selector supported     */
74 #define ADVERTISE_10HALF	0x0020	/* Try for 10mbps half-duplex  */
75 #define ADVERTISE_1000XFULL	0x0020	/* Try for 1000BASE-X full-duplex */
76 #define ADVERTISE_10FULL	0x0040	/* Try for 10mbps full-duplex  */
77 #define ADVERTISE_1000XHALF	0x0040	/* Try for 1000BASE-X half-duplex */
78 #define ADVERTISE_100HALF	0x0080	/* Try for 100mbps half-duplex */
79 #define ADVERTISE_1000XPAUSE	0x0080	/* Try for 1000BASE-X pause    */
80 #define ADVERTISE_100FULL	0x0100	/* Try for 100mbps full-duplex */
81 #define ADVERTISE_1000XPSE_ASYM	0x0100	/* Try for 1000BASE-X asym pause */
82 #define ADVERTISE_100BASE4	0x0200	/* Try for 100mbps 4k packets  */
83 #define ADVERTISE_PAUSE_CAP	0x0400	/* Try for pause               */
84 #define ADVERTISE_PAUSE_ASYM	0x0800	/* Try for asymetric pause     */
85 #define ADVERTISE_RESV		0x1000	/* Unused...                   */
86 #define ADVERTISE_RFAULT	0x2000	/* Say we can detect faults    */
87 #define ADVERTISE_LPACK		0x4000	/* Ack link partners response  */
88 #define ADVERTISE_NPAGE		0x8000	/* Next page bit               */
89 
90 #define ADVERTISE_FULL		(ADVERTISE_100FULL | ADVERTISE_10FULL | \
91 				  ADVERTISE_CSMA)
92 #define ADVERTISE_ALL		(ADVERTISE_10HALF | ADVERTISE_10FULL | \
93 				  ADVERTISE_100HALF | ADVERTISE_100FULL)
94 
95 /* Link partner ability register. */
96 #define LPA_SLCT		0x001f	/* Same as advertise selector  */
97 #define LPA_10HALF		0x0020	/* Can do 10mbps half-duplex   */
98 #define LPA_1000XFULL		0x0020	/* Can do 1000BASE-X full-duplex */
99 #define LPA_10FULL		0x0040	/* Can do 10mbps full-duplex   */
100 #define LPA_1000XHALF		0x0040	/* Can do 1000BASE-X half-duplex */
101 #define LPA_100HALF		0x0080	/* Can do 100mbps half-duplex  */
102 #define LPA_1000XPAUSE		0x0080	/* Can do 1000BASE-X pause     */
103 #define LPA_100FULL		0x0100	/* Can do 100mbps full-duplex  */
104 #define LPA_1000XPAUSE_ASYM	0x0100	/* Can do 1000BASE-X pause asym*/
105 #define LPA_100BASE4		0x0200	/* Can do 100mbps 4k packets   */
106 #define LPA_PAUSE_CAP		0x0400	/* Can pause                   */
107 #define LPA_PAUSE_ASYM		0x0800	/* Can pause asymetrically     */
108 #define LPA_RESV		0x1000	/* Unused...                   */
109 #define LPA_RFAULT		0x2000	/* Link partner faulted        */
110 #define LPA_LPACK		0x4000	/* Link partner acked us       */
111 #define LPA_NPAGE		0x8000	/* Next page bit               */
112 
113 #define LPA_DUPLEX		(LPA_10FULL | LPA_100FULL)
114 #define LPA_100			(LPA_100FULL | LPA_100HALF | LPA_100BASE4)
115 
116 /* Expansion register for auto-negotiation. */
117 #define EXPANSION_NWAY		0x0001	/* Can do N-way auto-nego      */
118 #define EXPANSION_LCWP		0x0002	/* Got new RX page code word   */
119 #define EXPANSION_ENABLENPAGE	0x0004	/* This enables npage words    */
120 #define EXPANSION_NPCAPABLE	0x0008	/* Link partner supports npage */
121 #define EXPANSION_MFAULTS	0x0010	/* Multiple faults detected    */
122 #define EXPANSION_RESV		0xffe0	/* Unused...                   */
123 
124 #define ESTATUS_1000_XFULL	0x8000	/* Can do 1000BaseX Full       */
125 #define ESTATUS_1000_XHALF	0x4000	/* Can do 1000BaseX Half       */
126 #define ESTATUS_1000_TFULL	0x2000	/* Can do 1000BT Full          */
127 #define ESTATUS_1000_THALF	0x1000	/* Can do 1000BT Half          */
128 
129 /* N-way test register. */
130 #define NWAYTEST_RESV1		0x00ff	/* Unused...                   */
131 #define NWAYTEST_LOOPBACK	0x0100	/* Enable loopback for N-way   */
132 #define NWAYTEST_RESV2		0xfe00	/* Unused...                   */
133 
134 /* MAC and PHY tx_config_Reg[15:0] for SGMII in-band auto-negotiation.*/
135 #define ADVERTISE_SGMII		0x0001	/* MAC can do SGMII            */
136 #define LPA_SGMII		0x0001	/* PHY can do SGMII            */
137 #define LPA_SGMII_SPD_MASK	0x0c00	/* SGMII speed mask            */
138 #define LPA_SGMII_FULL_DUPLEX	0x1000	/* SGMII full duplex           */
139 #define LPA_SGMII_DPX_SPD_MASK	0x1C00	/* SGMII duplex and speed bits */
140 #define LPA_SGMII_10		0x0000	/* 10Mbps                      */
141 #define LPA_SGMII_10HALF	0x0000	/* Can do 10mbps half-duplex   */
142 #define LPA_SGMII_10FULL	0x1000	/* Can do 10mbps full-duplex   */
143 #define LPA_SGMII_100		0x0400	/* 100Mbps                     */
144 #define LPA_SGMII_100HALF	0x0400	/* Can do 100mbps half-duplex  */
145 #define LPA_SGMII_100FULL	0x1400	/* Can do 100mbps full-duplex  */
146 #define LPA_SGMII_1000		0x0800	/* 1000Mbps                    */
147 #define LPA_SGMII_1000HALF	0x0800	/* Can do 1000mbps half-duplex */
148 #define LPA_SGMII_1000FULL	0x1800	/* Can do 1000mbps full-duplex */
149 #define LPA_SGMII_LINK		0x8000	/* PHY link with copper-side partner */
150 
151 /* 1000BASE-T Control register */
152 #define ADVERTISE_1000FULL	0x0200  /* Advertise 1000BASE-T full duplex */
153 #define ADVERTISE_1000HALF	0x0100  /* Advertise 1000BASE-T half duplex */
154 #define CTL1000_PREFER_MASTER	0x0400  /* prefer to operate as master */
155 #define CTL1000_AS_MASTER	0x0800
156 #define CTL1000_ENABLE_MASTER	0x1000
157 
158 /* 1000BASE-T Status register */
159 #define LPA_1000MSFAIL		0x8000	/* Master/Slave resolution failure */
160 #define LPA_1000MSRES		0x4000	/* Master/Slave resolution status */
161 #define LPA_1000LOCALRXOK	0x2000	/* Link partner local receiver status */
162 #define LPA_1000REMRXOK		0x1000	/* Link partner remote receiver status */
163 #define LPA_1000FULL		0x0800	/* Link partner 1000BASE-T full duplex */
164 #define LPA_1000HALF		0x0400	/* Link partner 1000BASE-T half duplex */
165 
166 /* Flow control flags */
167 #define FLOW_CTRL_TX		0x01
168 #define FLOW_CTRL_RX		0x02
169 
170 /* MMD Access Control register fields */
171 #define MII_MMD_CTRL_DEVAD_MASK	0x1f	/* Mask MMD DEVAD*/
172 #define MII_MMD_CTRL_ADDR	0x0000	/* Address */
173 #define MII_MMD_CTRL_NOINCR	0x4000	/* no post increment */
174 #define MII_MMD_CTRL_INCR_RDWT	0x8000	/* post increment on reads & writes */
175 #define MII_MMD_CTRL_INCR_ON_WT	0xC000	/* post increment on writes only */
176 
177 /* This structure is used in all SIOCxMIIxxx ioctl calls */
178 struct mii_ioctl_data {
179 	__u16		phy_id;
180 	__u16		reg_num;
181 	__u16		val_in;
182 	__u16		val_out;
183 };
184 
185 #endif /* _UAPI__LINUX_MII_H__ */
186