1 /* $NetBSD: spr.h,v 1.7 2020/07/06 10:31:23 rin Exp $ */
2
3 #ifndef _POWERPC_OEA_SPR_H_
4 #define _POWERPC_OEA_SPR_H_
5
6 #if !defined(_LOCORE) && defined(_KERNEL)
7
8 #ifdef _KERNEL_OPT
9 #include "opt_ppcarch.h"
10 #endif
11
12 #if defined(PPC_OEA64_BRIDGE) || defined (_ARCH_PPC64)
13 #include <powerpc/psl.h>
14 #include <powerpc/spr.h>
15 #endif
16
17 #endif /* !_LOCORE && _KERNEL */
18
19 /*
20 * Special Purpose Register declarations.
21 *
22 * The first column in the comments indicates which PowerPC architectures the
23 * SPR is valid on - E for BookE series, 4 for 4xx series,
24 * 6 for 6xx/7xx series and 8 for 8xx (but not most 8xxx) series.
25 */
26
27 #define SPR_MQ 0x000 /* ..6. 601 MQ register */
28 #define SPR_RTCU_R 0x004 /* ..6. 601 RTC Upper - Read */
29 #define SPR_RTCL_R 0x005 /* ..6. 601 RTC Lower - Read */
30 #define SPR_DSISR 0x012 /* ..68 DSI exception source */
31 #define DSISR_DIRECT 0x80000000 /* Direct-store error exception */
32 #define DSISR_NOTFOUND 0x40000000 /* Translation not found */
33 #define DSISR_PROTECT 0x08000000 /* Memory access not permitted */
34 #define DSISR_INVRX 0x04000000 /* Reserve-indexed insn direct-store access */
35 #define DSISR_STORE 0x02000000 /* Store operation */
36 #define DSISR_DABR 0x00400000 /* DABR match */
37 #define DSISR_SEGMENT 0x00200000 /* XXX; not in 6xx PEM */
38 #define DSISR_EAR 0x00100000 /* eciwx/ecowx && EAR[E] == 0 */
39 #define SPR_DAR 0x013 /* ..68 Data Address Register */
40 #define SPR_RTCU_W 0x014 /* ..6. 601 RTC Upper - Write */
41 #define SPR_RTCL_W 0x015 /* ..6. 601 RTC Lower - Write */
42 #define SPR_SDR1 0x019 /* ..68 Page table base address register */
43 #define SPR_VRSAVE 0x100 /* ..6. AltiVec VRSAVE */
44 #define SPR_SCOMC 0x114 /* .... SCOM Control Register (970) */
45 #define SPR_SCOMD 0x115 /* .... SCOM Data Register (970) */
46 #define SCOM_PCR 0x0aa00100 /* Power Control Register */
47 #define SCOM_PCR_BIT 0x80000000 /* Data bit */
48 #define SCOM_PSR 0x40800100 /* Power Status Register */
49 #define PSR_RECEIVED (1ULL << 61)
50 #define PSR_COMPLETED (1ULL << 60)
51 #define SCOMC_READ 0x00008000
52 #define SCOMC_WRITE 0x00000000
53 #define SPR_ASR 0x118 /* ..6. Address Space Register (PPC64) */
54 #define SPR_EAR 0x11a /* ..68 External Access Register */
55 #define MPC601 0x0001
56 #define MPC603 0x0003
57 #define MPC604 0x0004
58 #define MPC602 0x0005
59 #define MPC603e 0x0006
60 #define MPC603ev 0x0007
61 #define MPC750 0x0008
62 #define MPC604e 0x0009
63 #define MPC604ev 0x000a
64 #define MPC7400 0x000c
65 #define MPC620 0x0014
66 #define IBMRS64II 0x0033
67 #define IBMRS64IIIp 0x0034
68 #define IBMPOWER4 0x0035
69 #define IBMRS64IIIi 0x0036
70 #define IBMRS64IV 0x0037
71 #define IBMPOWER4II 0x0038
72 #define IBM970 0x0039
73 #define IBMPOWER5GR 0x003a
74 #define IBMPOWER5GS 0x003b
75 #define IBM970FX 0x003c
76 #define IBMPOWER6 0x003e
77 #define IBMPOWER3 0x0040
78 #define IBMPOWER3II 0x0041
79 #define IBM970MP 0x0044
80 #define IBM970GX 0x0045
81 #define IBMCELL 0x0070
82 #define MPC8240 0x0081
83 #define PA6T 0x0090
84 #define IBMPOWER6P5 0x0f00
85 #define IBMSTB25 0x5151
86 #define IBM750FX 0x7000
87 #define IBM750GX 0x7002
88 #define MPC7450 0x8000
89 #define MPC7455 0x8001
90 #define MPC7457 0x8002
91 #define MPC7447A 0x8003
92 #define MPC7448 0x8004
93 #define MPC745X_P(v) ((v & 0xFFF8) == 0x8000)
94 #define MPC7410 0x800c
95 #define MPC5200 0x8011
96 #define MPC8245 0x8081
97 #define MPCG2 0x8082
98 #define MPCe300c1 0x8083
99 #define MPCe300c2 0x8084
100 #define MPCe300c3 0x8085
101 #define SPR_HIOR 0x137 /* .... HW Interrupt Offset (970) */
102
103 #define SPR_IBAT0U 0x210 /* ..68 Instruction BAT Reg 0 Upper */
104 #define SPR_IBAT0L 0x211 /* ..6. Instruction BAT Reg 0 Lower */
105 #define SPR_IBAT1U 0x212 /* ..6. Instruction BAT Reg 1 Upper */
106 #define SPR_IBAT1L 0x213 /* ..6. Instruction BAT Reg 1 Lower */
107 #define SPR_IBAT2U 0x214 /* ..6. Instruction BAT Reg 2 Upper */
108 #define SPR_IBAT2L 0x215 /* ..6. Instruction BAT Reg 2 Lower */
109 #define SPR_IBAT3U 0x216 /* ..6. Instruction BAT Reg 3 Upper */
110 #define SPR_IBAT3L 0x217 /* ..6. Instruction BAT Reg 3 Lower */
111 #define SPR_DBAT0U 0x218 /* ..6. Data BAT Reg 0 Upper */
112 #define SPR_DBAT0L 0x219 /* ..6. Data BAT Reg 0 Lower */
113 #define SPR_DBAT1U 0x21a /* ..6. Data BAT Reg 1 Upper */
114 #define SPR_DBAT1L 0x21b /* ..6. Data BAT Reg 1 Lower */
115 #define SPR_DBAT2U 0x21c /* ..6. Data BAT Reg 2 Upper */
116 #define SPR_DBAT2L 0x21d /* ..6. Data BAT Reg 2 Lower */
117 #define SPR_DBAT3U 0x21e /* ..6. Data BAT Reg 3 Upper */
118 #define SPR_DBAT3L 0x21f /* ..6. Data BAT Reg 3 Lower */
119 #define SPR_IBAT4U 0x230 /* ..6. Instruction BAT Reg 4 Upper */
120 #define SPR_IBAT4L 0x231 /* ..6. Instruction BAT Reg 4 Lower */
121 #define SPR_IBAT5U 0x232 /* ..6. Instruction BAT Reg 5 Upper */
122 #define SPR_IBAT5L 0x233 /* ..6. Instruction BAT Reg 5 Lower */
123 #define SPR_IBAT6U 0x234 /* ..6. Instruction BAT Reg 6 Upper */
124 #define SPR_IBAT6L 0x235 /* ..6. Instruction BAT Reg 6 Lower */
125 #define SPR_IBAT7U 0x236 /* ..6. Instruction BAT Reg 7 Upper */
126 #define SPR_IBAT7L 0x237 /* ..6. Instruction BAT Reg 7 Lower */
127 #define SPR_DBAT4U 0x238 /* ..6. Data BAT Reg 4 Upper */
128 #define SPR_DBAT4L 0x239 /* ..6. Data BAT Reg 4 Lower */
129 #define SPR_DBAT5U 0x23a /* ..6. Data BAT Reg 5 Upper */
130 #define SPR_DBAT5L 0x23b /* ..6. Data BAT Reg 5 Lower */
131 #define SPR_DBAT6U 0x23c /* ..6. Data BAT Reg 6 Upper */
132 #define SPR_DBAT6L 0x23d /* ..6. Data BAT Reg 6 Lower */
133 #define SPR_DBAT7U 0x23e /* ..6. Data BAT Reg 7 Upper */
134 #define SPR_DBAT7L 0x23f /* ..6. Data BAT Reg 7 Upper */
135 #define SPR_UMMCR2 0x3a0 /* ..6. User Monitor Mode Control Register 2 */
136 #define SPR_UMMCR0 0x3a8 /* ..6. User Monitor Mode Control Register 0 */
137 #define SPR_USIA 0x3ab /* ..6. User Sampled Instruction Address */
138 #define SPR_UMMCR1 0x3ac /* ..6. User Monitor Mode Control Register 1 */
139 #define SPR_MMCR2 0x3b0 /* ..6. Monitor Mode Control Register 2 */
140 #define SPR_MMCR2_THRESHMULT_32 0x80000000 /* Multiply MMCR0 threshold by 32 */
141 #define SPR_MMCR2_THRESHMULT_2 0x00000000 /* Multiply MMCR0 threshold by 2 */
142 #define SPR_PMC5 0x3b1 /* ..6. Performance Counter Register 5 */
143 #define SPR_PMC6 0x3b2 /* ..6. Performance Counter Register 6 */
144
145 #define SPR_MMCR0 0x3b8 /* ..6. Monitor Mode Control Register 0 */
146 #define MMCR0_FC 0x80000000 /* Freeze counters */
147 #define MMCR0_FCS 0x40000000 /* Freeze counters in supervisor mode */
148 #define MMCR0_FCP 0x20000000 /* Freeze counters in user mode */
149 #define MMCR0_FCM1 0x10000000 /* Freeze counters when mark=1 */
150 #define MMCR0_FCM0 0x08000000 /* Freeze counters when mark=0 */
151 #define MMCR0_PMXE 0x04000000 /* Enable PM interrupt */
152 #define MMCR0_FCECE 0x02000000 /* Freeze counters after event */
153 #define MMCR0_TBSEL_15 0x01800000 /* Count bit 15 of TBL */
154 #define MMCR0_TBSEL_19 0x01000000 /* Count bit 19 of TBL */
155 #define MMCR0_TBSEL_23 0x00800000 /* Count bit 23 of TBL */
156 #define MMCR0_TBSEL_31 0x00000000 /* Count bit 31 of TBL */
157 #define MMCR0_TBEE 0x00400000 /* Time-base event enable */
158 #define MMCRO_THRESHOLD(x) ((x) << 16) /* Threshold value */
159 #define MMCR0_PMC1CE 0x00008000 /* PMC1 condition enable */
160 #define MMCR0_PMCNCE 0x00004000 /* PMCn condition enable */
161 #define MMCR0_TRIGGER 0x00002000 /* Trigger */
162 #define MMCR0_PMC1SEL(x) ((x) << 6) /* PMC1 selector */
163 #define MMCR0_PMC2SEL(x) ((x) << 0) /* PMC2 selector */
164 #define SPR_PMC1 0x3b9 /* ..6. Performance Counter Register 1 */
165 #define SPR_PMC2 0x3ba /* ..6. Performance Counter Register 2 */
166 #define SPR_SIA 0x3bb /* ..6. Sampled Instruction Address */
167 #define SPR_MMCR1 0x3bc /* ..6. Monitor Mode Control Register 2 */
168 #define MMCR1_PMC3SEL(x) ((x) << 27) /* PMC 3 selector */
169 #define MMCR1_PMC4SEL(x) ((x) << 22) /* PMC 4 selector */
170 #define MMCR1_PMC5SEL(x) ((x) << 17) /* PMC 5 selector */
171 #define MMCR1_PMC6SEL(x) ((x) << 11) /* PMC 6 selector */
172
173 #define SPR_PMC3 0x3bd /* ..6. Performance Counter Register 3 */
174 #define SPR_PMC4 0x3be /* ..6. Performance Counter Register 4 */
175 #define SPR_DMISS 0x3d0 /* ..68 Data TLB Miss Address Register */
176 #define SPR_DCMP 0x3d1 /* ..68 Data TLB Compare Register */
177 #define SPR_HASH1 0x3d2 /* ..68 Primary Hash Address Register */
178 #define SPR_HASH2 0x3d3 /* ..68 Secondary Hash Address Register */
179 #define SPR_IMISS 0x3d4 /* ..68 Instruction TLB Miss Address Register */
180 #define SPR_TLBMISS 0x3d4 /* ..6. TLB Miss Address Register */
181 #define SPR_ICMP 0x3d5 /* ..68 Instruction TLB Compare Register */
182 #define SPR_PTEHI 0x3d5 /* ..6. Instruction TLB Compare Register */
183 #define SPR_RPA 0x3d6 /* ..68 Required Physical Address Register */
184 #define SPR_PTELO 0x3d6 /* ..6. Required Physical Address Register */
185 #define SPR_HID0 0x3f0 /* E.68 Hardware Implementation Register
186 0 */
187 #define SPR_HID1 0x3f1 /* E.68 Hardware Implementation Register
188 1 */
189 #define SPR_HID4 0x3f4 /* ..6. 970 HID4 */
190 #define SPR_HID5 0x3f6 /* ..6. 970 HID5 */
191 #define SPR_DABR 0x3f5 /* ..6. Data Address Breakpoint Register */
192 #define SPR_MSSCR0 0x3f6 /* ..6. Memory SubSystem Control Register */
193 #define MSSCR0_SHDEN 0x80000000 /* 0: Shared-state enable */
194 #define MSSCR0_SHDPEN3 0x40000000 /* 1: ~SHD[01] signal enable in MEI mode */
195 #define MSSCR0_L1INTVEN 0x38000000 /* 2-4: L1 data cache ~HIT intervention enable */
196 #define MSSCR0_L2INTVEN 0x07000000 /* 5-7: L2 data cache ~HIT intervention enable */
197 #define MSSCR0_DL1HWF 0x00800000 /* 8: L1 data cache hardware flush */
198 #define MSSCR0_MBO 0x00400000 /* 9: must be one */
199 #define MSSCR0_EMODE 0x00200000 /* 10: MPX bus mode (read-only) */
200 #define MSSCR0_ABD 0x00100000 /* 11: address bus driven (read-only) */
201 #define MSSCR0_BMODE 0x0000c000 /* 16-17: Bus Mode (read-only) (7450) */
202 #define MSSCR0_ID 0x00000040 /* 26: Processor ID */
203 #define MSSCR0_L2PFE 0x00000003 /* 30-31: L2 prefetching enabled (7450) */
204 #define SPR_L2PM 0x3f8 /* ..6. L2 Private Memory Control Register */
205 #define SPR_L2CR 0x3f9 /* ..6. L2 Control Register */
206 #define L2CR_L2E 0x80000000 /* 0: L2 enable */
207 #define L2CR_L2PE 0x40000000 /* 1: L2 data parity enable */
208 #define L2CR_L2SIZ 0x30000000 /* 2-3: L2 size */
209 #define L2SIZ_2M 0x00000000
210 #define L2SIZ_256K 0x10000000
211 #define L2SIZ_512K 0x20000000
212 #define L2SIZ_1M 0x30000000
213 #define L2CR_L2CLK 0x0e000000 /* 4-6: L2 clock ratio */
214 #define L2CLK_DIS 0x00000000 /* disable L2 clock */
215 #define L2CLK_10 0x02000000 /* core clock / 1 */
216 #define L2CLK_15 0x04000000 /* / 1.5 */
217 #define L2CLK_35 0x06000000 /* / 3.5 */
218 #define L2CLK_20 0x08000000 /* / 2 */
219 #define L2CLK_25 0x0a000000 /* / 2.5 */
220 #define L2CLK_30 0x0c000000 /* / 3 */
221 #define L2CLK_40 0x0e000000 /* / 4 */
222 #define L2CR_L2RAM 0x01800000 /* 7-8: L2 RAM type */
223 #define L2RAM_FLOWTHRU_BURST 0x00000000
224 #define L2RAM_PIPELINE_BURST 0x01000000
225 #define L2RAM_PIPELINE_LATE 0x01800000
226 #define L2CR_L2DO 0x00400000 /* 9: L2 data-only.
227 Setting this bit disables instruction
228 caching. */
229 #define L2CR_L2I 0x00200000 /* 10: L2 global invalidate. */
230 #define L2CR_L2CTL 0x00100000 /* 11: L2 RAM control (ZZ enable).
231 Enables automatic operation of the
232 L2ZZ (low-power mode) signal. */
233 #define L2CR_L2WT 0x00080000 /* 12: L2 write-through. */
234 #define L2CR_L2TS 0x00040000 /* 13: L2 test support. */
235 #define L2CR_L2OH 0x00030000 /* 14-15: L2 output hold. */
236 #define L2CR_L2SL 0x00008000 /* 16: L2 DLL slow. */
237 #define L2CR_L2DF 0x00004000 /* 17: L2 differential clock. */
238 #define L2CR_L2BYP 0x00002000 /* 18: L2 DLL bypass. */
239 #define L2CR_L2FA 0x00001000 /* 19: L2 flush assist (for software flush). */
240 #define L2CR_L2HWF 0x00000800 /* 20: L2 hardware flush. */
241 #define L2CR_L2IO 0x00000400 /* 21: L2 instruction-only. */
242 #define L2CR_L2CLKSTP 0x00000200 /* 22: L2 clock stop. */
243 #define L2CR_L2DRO 0x00000100 /* 23: L2DLL rollover checkstop enable. */
244 #define L2CR_L2IP 0x00000001 /* 31: L2 global invalidate in */
245 /* progress (read only). */
246 #define SPR_L3CR 0x3fa /* ..6. L3 Control Register */
247 #define L3CR_RESERVED 0x0438003a /* Reserved bits in L3CR */
248 #define L3CR_L3E 0x80000000 /* 0: L3 enable */
249 #define L3CR_L3PE 0x40000000 /* 1: L3 data parity checking enable */
250 #define L3CR_L3APE 0x20000000 /* 2: L3 address parity checking enable */
251 #define L3CR_L3SIZ 0x10000000 /* 3: L3 size (0=1MB, 1=2MB) */
252 #define L3SIZ_1M 0x00000000
253 #define L3SIZ_2M 0x10000000
254 #define L3CR_L3CLKEN 0x08000000 /* 4: Enables the L3_CLK[0:1] signals */
255 #define L3CR_L3CLK 0x03800000 /* 6-8: L3 clock ratio */
256 #define L3CLK_60 0x00000000 /* core clock / 6 */
257 #define L3CLK_20 0x01000000 /* / 2 */
258 #define L3CLK_25 0x01800000 /* / 2.5 */
259 #define L3CLK_30 0x02000000 /* / 3 */
260 #define L3CLK_35 0x02800000 /* / 3.5 */
261 #define L3CLK_40 0x03000000 /* / 4 */
262 #define L3CLK_50 0x03800000 /* / 5 */
263 #define L3CR_L3IO 0x00400000 /* 9: L3 instruction-only mode */
264 #define L3CR_L3SPO 0x00040000 /* 13: L3 sample point override */
265 #define L3CR_L3CKSP 0x00030000 /* 14-15: L3 clock sample point */
266 #define L3CKSP_2 0x00000000 /* 2 clocks */
267 #define L3CKSP_3 0x00010000 /* 3 clocks */
268 #define L3CKSP_4 0x00020000 /* 4 clocks */
269 #define L3CKSP_5 0x00030000 /* 5 clocks */
270 #define L3CR_L3PSP 0x0000e000 /* 16-18: L3 P-clock sample point */
271 #define L3PSP_0 0x00000000 /* 0 clocks */
272 #define L3PSP_1 0x00002000 /* 1 clocks */
273 #define L3PSP_2 0x00004000 /* 2 clocks */
274 #define L3PSP_3 0x00006000 /* 3 clocks */
275 #define L3PSP_4 0x00008000 /* 4 clocks */
276 #define L3PSP_5 0x0000a000 /* 5 clocks */
277 #define L3CR_L3REP 0x00001000 /* 19: L3 replacement algorithm (0=default, 1=alternate) */
278 #define L3CR_L3HWF 0x00000800 /* 20: L3 hardware flush */
279 #define L3CR_L3I 0x00000400 /* 21: L3 global invalidate */
280 #define L3CR_L3RT 0x00000300 /* 22-23: L3 SRAM type */
281 #define L3RT_MSUG2_DDR 0x00000000 /* MSUG2 DDR SRAM */
282 #define L3RT_PIPELINE_LATE 0x00000100 /* Pipelined (register-register) synchronous late-write SRAM */
283 #define L3RT_PB2_SRAM 0x00000300 /* PB2 SRAM */
284 #define L3CR_L3NIRCA 0x00000080 /* 24: L3 non-integer ratios clock adjustment for the SRAM */
285 #define L3CR_L3DO 0x00000040 /* 25: L3 data-only mode */
286 #define L3CR_PMEN 0x00000004 /* 29: Private memory enable */
287 #define L3CR_PMSIZ 0x00000004 /* 31: Private memory size (0=1MB, 1=2MB) */
288 #define SPR_ICTC 0x3fb /* ..6. instruction cache throttling */
289 #define ICTC_ENABLE 0x00000001 /* enable throttling */
290 #define ICTC_COUNT_M 0x000001fe /* number of waits to insert */
291 #define SPR_THRM1 0x3fc /* ..6. Thermal Management Register */
292 #define SPR_THRM2 0x3fd /* ..6. Thermal Management Register */
293 #define SPR_THRM_TIN 0x80000000 /* Thermal interrupt bit (RO) */
294 #define SPR_THRM_TIV 0x40000000 /* Thermal interrupt valid (RO) */
295 #define SPR_THRM_THRESHOLD(x) ((x) << 23) /* Thermal sensor threshold */
296 #define SPR_THRM_TID 0x00000004 /* Thermal interrupt direction */
297 #define SPR_THRM_TIE 0x00000002 /* Thermal interrupt enable */
298 #define SPR_THRM_VALID 0x00000001 /* Valid bit */
299 #define SPR_THRM3 0x3fe /* ..6. Thermal Management Register */
300 #define SPR_THRM_TIMER(x) ((x) << 1) /* Sampling interval timer */
301 #define SPR_THRM_ENABLE 0x00000001 /* TAU Enable */
302 #define SPR_FPECR 0x3fe /* ..6. Floating-Point Exception Cause Register */
303 #define SPR_PIR 0x3ff /* ..6. Processor Identification Register */
304
305 /* Performance counter declarations */
306 #define PMC_OVERFLOW 0x80000000 /* Counter has overflowed */
307
308 /* The first five countable [non-]events are common to all the PMC's */
309 #define PMCN_NONE 0 /* Count nothing */
310 #define PMCN_CYCLES 1 /* Processor cycles */
311 #define PMCN_ICOMP 2 /* Instructions completed */
312 #define PMCN_TBLTRANS 3 /* TBL bit transitions */
313 #define PCMN_IDISPATCH 4 /* Instructions dispatched */
314
315 #if !defined(_LOCORE) && defined(_KERNEL)
316
317 #if defined(PPC_OEA64_BRIDGE) || defined (_ARCH_PPC64)
318
319 static inline uint64_t
scom_read(register_t address)320 scom_read(register_t address)
321 {
322 register_t msr;
323 uint64_t ret;
324
325 msr = mfmsr();
326 mtmsr(msr & ~PSL_EE);
327 __asm volatile("isync;");
328
329 mtspr(SPR_SCOMC, address | SCOMC_READ);
330 __asm volatile("isync;");
331
332 ret = mfspr(SPR_SCOMD);
333 mtmsr(msr);
334 __asm volatile("isync;");
335
336 return ret;
337 }
338
339 static inline void
scom_write(register_t address,uint64_t data)340 scom_write(register_t address, uint64_t data)
341 {
342 register_t msr;
343
344 msr = mfmsr();
345 mtmsr(msr & ~PSL_EE);
346 __asm volatile("isync;");
347
348 mtspr(SPR_SCOMD, data);
349 __asm volatile("isync;");
350 mtspr(SPR_SCOMC, address | SCOMC_WRITE);
351 __asm volatile("isync;");
352
353 mtmsr(msr);
354 __asm volatile("isync;");
355 }
356
357 #endif /* defined(PPC_OEA64_BRIDGE) || defined (_ARCH_PPC64) */
358
359 #endif /* !defined(_LOCORE) && defined(_KERNEL) */
360
361 #endif /* !_POWERPC_SPR_H_ */
362