1 /* 2 * (C) Copyright 2000, 2001 3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. 4 * 5 * (C) Copyright 2001 6 * James F. Dougherty (jfd@cs.stanford.edu) 7 * 8 * See file CREDITS for list of people who contributed to this 9 * project. 10 * 11 * This program is free software; you can redistribute it and/or 12 * modify it under the terms of the GNU General Public License as 13 * published by the Free Software Foundation; either version 2 of 14 * the License, or (at your option) any later version. 15 * 16 * This program is distributed in the hope that it will be useful, 17 * but WITHOUT ANY WARRANTY; without even the implied warranty of 18 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 19 * GNU General Public License for more details. 20 * 21 * You should have received a copy of the GNU General Public License 22 * along with this program; if not, write to the Free Software 23 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 24 * MA 02111-1307 USA 25 */ 26 27 /* 28 * 29 * Configuration settings for the MOUSSE board. 30 * See also: http://www.vooha.com/ 31 * 32 */ 33 34 /* ------------------------------------------------------------------------- */ 35 36 /* 37 * board/config.h - configuration options, board specific 38 */ 39 40 #ifndef __CONFIG_H 41 #define __CONFIG_H 42 43 /* 44 * High Level Configuration Options 45 * (easy to change) 46 */ 47 48 #define CONFIG_MPC824X 1 49 #define CONFIG_MPC8240 1 50 #define CONFIG_MOUSSE 1 51 #define CONFIG_SYS_ADDR_MAP_B 1 52 #define CONFIG_CONS_INDEX 1 53 #define CONFIG_BAUDRATE 9600 54 #if 1 55 #define CONFIG_BOOTCOMMAND "tftp 100000 vmlinux.img;bootm" /* autoboot command */ 56 #else 57 #define CONFIG_BOOTCOMMAND "bootm ffe10000" 58 #endif 59 #define CONFIG_BOOTARGS "console=ttyS0 root=/dev/nfs rw nfsroot=209.128.93.133:/boot nfsaddrs=209.128.93.133:209.128.93.138" 60 #define CONFIG_BOOTDELAY 3 61 62 63 /* 64 * BOOTP options 65 */ 66 #define CONFIG_BOOTP_BOOTFILESIZE 67 #define CONFIG_BOOTP_BOOTPATH 68 #define CONFIG_BOOTP_GATEWAY 69 #define CONFIG_BOOTP_HOSTNAME 70 71 72 /* 73 * Command line configuration. 74 */ 75 #include <config_cmd_default.h> 76 77 #define CONFIG_CMD_ASKENV 78 #define CONFIG_CMD_DATE 79 80 81 #define CONFIG_ENV_OVERWRITE 1 82 #define CONFIG_ETH_ADDR "00:10:18:10:00:06" 83 84 #define CONFIG_DOS_PARTITION 1 /* MSDOS bootable partitiion support */ 85 86 #include "../board/mousse/mousse.h" 87 88 /* 89 * Miscellaneous configurable options 90 */ 91 #undef CONFIG_SYS_LONGHELP /* undef to save memory */ 92 #define CONFIG_SYS_PROMPT "=>" /* Monitor Command Prompt */ 93 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 94 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 95 #define CONFIG_SYS_MAXARGS 8 /* Max number of command args */ 96 97 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 98 #define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */ 99 100 /*----------------------------------------------------------------------- 101 * Start addresses for the final memory configuration 102 * (Set up by the startup code) 103 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 104 */ 105 #define CONFIG_SYS_SDRAM_BASE 0x00000000 106 107 #ifdef DEBUG 108 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_SDRAM_BASE 109 #else 110 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 111 #endif 112 113 #ifdef DEBUG 114 #define CONFIG_SYS_MONITOR_LEN (4 << 20) /* lots of mem ... */ 115 #else 116 #define CONFIG_SYS_MONITOR_LEN (512 << 10) /* 512K PLCC bootrom */ 117 #endif 118 #define CONFIG_SYS_MALLOC_LEN (2*(4096 << 10)) /* 2*4096kB for malloc() */ 119 120 #define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ 121 #define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ 122 123 124 #define CONFIG_SYS_EUMB_ADDR 0xFC000000 125 126 #define CONFIG_SYS_ISA_MEM 0xFD000000 127 #define CONFIG_SYS_ISA_IO 0xFE000000 128 129 #define CONFIG_SYS_FLASH_BASE 0xFFF00000 130 #define CONFIG_SYS_FLASH_SIZE ((uint)(512 * 1024)) 131 #define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 132 #define FLASH_BASE0_PRELIM 0xFFF00000 /* 512K PLCC FLASH/AM29F040*/ 133 #define FLASH_BASE0_SIZE 0x80000 /* 512K */ 134 #define FLASH_BASE1_PRELIM 0xFFE10000 /* AMD 29LV160DB 135 1MB - 64K FLASH0 SEG =960K 136 (size=0xf0000)*/ 137 138 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 139 140 /* 141 * NS16550 Configuration 142 */ 143 #define CONFIG_SYS_NS16550 144 #define CONFIG_SYS_NS16550_SERIAL 145 146 #define CONFIG_SYS_NS16550_REG_SIZE 1 147 148 #define CONFIG_SYS_NS16550_CLK 18432000 149 150 #define CONFIG_SYS_NS16550_COM1 0xFFE08080 151 152 /*----------------------------------------------------------------------- 153 * Definitions for initial stack pointer and data area (in DPRAM) 154 */ 155 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_MONITOR_LEN 156 #define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ 157 #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ 158 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 159 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 160 161 /* 162 * Low Level Configuration Settings 163 * (address mappings, register initial values, etc.) 164 * You should know what you are doing if you make changes here. 165 * For the detail description refer to the MPC8240 user's manual. 166 */ 167 168 #define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ 169 #define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 2 170 #define CONFIG_SYS_HZ 1000 171 172 #define CONFIG_SYS_ETH_DEV_FN 0x00 173 #define CONFIG_SYS_ETH_IOBASE 0x00104000 174 175 176 /* Bit-field values for MCCR1. 177 */ 178 #define CONFIG_SYS_ROMNAL 8 179 #define CONFIG_SYS_ROMFAL 8 180 181 /* Bit-field values for MCCR2. 182 */ 183 #define CONFIG_SYS_REFINT 0xf5 /* Refresh interval */ 184 185 /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. 186 */ 187 #define CONFIG_SYS_BSTOPRE 0x79 188 189 #ifdef INCLUDE_ECC 190 #define USE_ECC 1 191 #else /* INCLUDE_ECC */ 192 #define USE_ECC 0 193 #endif /* INCLUDE_ECC */ 194 195 196 /* Bit-field values for MCCR3. 197 */ 198 #define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */ 199 #define CONFIG_SYS_RDLAT (4+USE_ECC) /* Data latancy from read command */ 200 201 /* Bit-field values for MCCR4. 202 */ 203 #define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */ 204 #define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */ 205 #define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */ 206 #define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */ 207 #define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length */ 208 #define CONFIG_SYS_ACTORW 2 209 #define CONFIG_SYS_REGISTERD_TYPE_BUFFER (1-USE_ECC) 210 211 /* Memory bank settings. 212 * Only bits 20-29 are actually used from these vales to set the 213 * start/end addresses. The upper two bits will always be 0, and the lower 214 * 20 bits will be 0x00000 for a start address, or 0xfffff for an end 215 * address. Refer to the MPC8240 book. 216 */ 217 #define CONFIG_SYS_RAM_SIZE 0x04000000 /* 64MB */ 218 219 220 #define CONFIG_SYS_BANK0_START 0x00000000 221 #define CONFIG_SYS_BANK0_END (CONFIG_SYS_RAM_SIZE - 1) 222 #define CONFIG_SYS_BANK0_ENABLE 1 223 #define CONFIG_SYS_BANK1_START 0x3ff00000 224 #define CONFIG_SYS_BANK1_END 0x3fffffff 225 #define CONFIG_SYS_BANK1_ENABLE 0 226 #define CONFIG_SYS_BANK2_START 0x3ff00000 227 #define CONFIG_SYS_BANK2_END 0x3fffffff 228 #define CONFIG_SYS_BANK2_ENABLE 0 229 #define CONFIG_SYS_BANK3_START 0x3ff00000 230 #define CONFIG_SYS_BANK3_END 0x3fffffff 231 #define CONFIG_SYS_BANK3_ENABLE 0 232 #define CONFIG_SYS_BANK4_START 0x3ff00000 233 #define CONFIG_SYS_BANK4_END 0x3fffffff 234 #define CONFIG_SYS_BANK4_ENABLE 0 235 #define CONFIG_SYS_BANK5_START 0x3ff00000 236 #define CONFIG_SYS_BANK5_END 0x3fffffff 237 #define CONFIG_SYS_BANK5_ENABLE 0 238 #define CONFIG_SYS_BANK6_START 0x3ff00000 239 #define CONFIG_SYS_BANK6_END 0x3fffffff 240 #define CONFIG_SYS_BANK6_ENABLE 0 241 #define CONFIG_SYS_BANK7_START 0x3ff00000 242 #define CONFIG_SYS_BANK7_END 0x3fffffff 243 #define CONFIG_SYS_BANK7_ENABLE 0 244 245 #define CONFIG_SYS_ODCR 0x7f 246 247 248 #define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 reatins the currently accessed page in memory 249 see 8240 book for details*/ 250 #define PCI_MEM_SPACE1_START 0x80000000 251 #define PCI_MEM_SPACE2_START 0xfd000000 252 253 /* IBAT/DBAT Configuration */ 254 /* Ram: 64MB, starts at address-0, r/w instruction/data */ 255 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP) 256 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) 257 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 258 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 259 260 /* MPLD/Port-X I/O Space : data and instruction read/write, cache-inhibit */ 261 #define CONFIG_SYS_IBAT1U (PORTX_DEV_BASE | BATU_BL_128M | BATU_VS | BATU_VP) 262 #if 0 263 #define CONFIG_SYS_IBAT1L (PORTX_DEV_BASE | BATL_PP_10 | BATL_MEMCOHERENCE |\ 264 BATL_WRITETHROUGH | BATL_CACHEINHIBIT) 265 #else 266 #define CONFIG_SYS_IBAT1L (PORTX_DEV_BASE | BATL_PP_10 |BATL_CACHEINHIBIT) 267 #endif 268 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 269 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 270 271 /* PCI Memory region 1: 0x8XXX_XXXX PCI Mem space: EUMBAR, etc - 16MB */ 272 #define CONFIG_SYS_IBAT2U (PCI_MEM_SPACE1_START|BATU_BL_16M | BATU_VS | BATU_VP) 273 #define CONFIG_SYS_IBAT2L (PCI_MEM_SPACE1_START|BATL_PP_10 | BATL_GUARDEDSTORAGE|BATL_CACHEINHIBIT) 274 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 275 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 276 277 /* PCI Memory region 2: PCI Devices in 0xFD space */ 278 #define CONFIG_SYS_IBAT3U (PCI_MEM_SPACE2_START|BATU_BL_16M | BATU_VS | BATU_VP) 279 #define CONFIG_SYS_IBAT3L (PCI_MEM_SPACE2_START|BATL_PP_10 | BATL_GUARDEDSTORAGE | BATL_CACHEINHIBIT) 280 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 281 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 282 283 284 /* 285 * For booting Linux, the board info and command line data 286 * have to be in the first 8 MB of memory, since this is 287 * the maximum mapped by the Linux kernel during initialization. 288 */ 289 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 290 291 /*----------------------------------------------------------------------- 292 * FLASH organization 293 */ 294 #define CONFIG_SYS_MAX_FLASH_BANKS 3 /* Max number of flash banks */ 295 #define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors in one bank */ 296 297 #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ 298 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ 299 300 #if 0 301 #define CONFIG_ENV_IS_IN_FLASH 1 302 #define CONFIG_ENV_OFFSET 0x8000 /* Offset of the Environment Sector */ 303 #define CONFIG_ENV_SIZE 0x4000 /* Size of the Environment Sector */ 304 #else 305 #define CONFIG_ENV_IS_IN_NVRAM 1 306 #define CONFIG_ENV_ADDR NV_OFF_U_BOOT_ADDR /* PortX NVM Free addr*/ 307 #define CONFIG_ENV_OFFSET CONFIG_ENV_ADDR 308 #define CONFIG_ENV_SIZE NV_U_BOOT_ENV_SIZE /* 2K */ 309 #endif 310 /*----------------------------------------------------------------------- 311 * Cache Configuration 312 */ 313 #define CONFIG_SYS_CACHELINE_SIZE 16 314 315 316 /* 317 * Internal Definitions 318 * 319 * Boot Flags 320 */ 321 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 322 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 323 324 /* Localizations */ 325 #if 0 326 #define CONFIG_ETHADDR 0:0:0:0:1:d 327 #define CONFIG_IPADDR 172.16.40.113 328 #define CONFIG_SERVERIP 172.16.40.111 329 #else 330 #define CONFIG_ETHADDR 0:0:0:0:1:d 331 #define CONFIG_IPADDR 209.128.93.138 332 #define CONFIG_SERVERIP 209.128.93.133 333 #endif 334 335 /*----------------------------------------------------------------------- 336 * PCI stuff 337 *----------------------------------------------------------------------- 338 */ 339 #define CONFIG_PCI /* include pci support */ 340 #undef CONFIG_PCI_PNP 341 342 #define CONFIG_NET_MULTI /* Multi ethernet cards support */ 343 344 #define CONFIG_TULIP 345 346 #endif /* __CONFIG_H */ 347