1 /* 2 * (C) Copyright 2003 3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. 4 * 5 * modified for TOP5200-series by Reinhard Meyer, www.emk-elektronik.de 6 * 7 * TOP5200 differences from IceCube: 8 * 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks 9 * bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins 10 * 1 SDRAM/DDRAM Bank up to 256 MB 11 * local VPD I2C Bus is software driven and uses 12 * GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL 13 * FLASH is re-located at 0xff000000 14 * Internal regs are at 0xf0000000 15 * Reset jumps to 0x00000100 16 * 17 * See file CREDITS for list of people who contributed to this 18 * project. 19 * 20 * This program is free software; you can redistribute it and/or 21 * modify it under the terms of the GNU General Public License as 22 * published by the Free Software Foundation; either version 2 of 23 * the License, or (at your option) any later version. 24 * 25 * This program is distributed in the hope that it will be useful, 26 * but WITHOUT ANY WARRANTY; without even the implied warranty of 27 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 28 * GNU General Public License for more details. 29 * 30 * You should have received a copy of the GNU General Public License 31 * along with this program; if not, write to the Free Software 32 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 33 * MA 02111-1307 USA 34 */ 35 36 #ifndef __CONFIG_H 37 #define __CONFIG_H 38 39 /* 40 * High Level Configuration Options 41 * (easy to change) 42 */ 43 44 #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ 45 #define CONFIG_MPC5200 1 /* More exactly a MPC5200 */ 46 #define CONFIG_TOP5200 1 /* ... on TOP5200 board - we need this for FEC.C */ 47 48 #define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ 49 50 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 51 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 52 53 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 54 55 /* 56 * Serial console configuration 57 */ 58 #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ 59 #define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */ 60 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } 61 62 63 #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) 64 /* 65 * PCI Mapping: 66 * 0x40000000 - 0x4fffffff - PCI Memory 67 * 0x50000000 - 0x50ffffff - PCI IO Space 68 */ 69 # define CONFIG_PCI 1 70 # define CONFIG_PCI_PNP 1 71 # define CONFIG_PCI_SCAN_SHOW 1 72 # define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 73 74 # define CONFIG_PCI_MEM_BUS 0x40000000 75 # define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS 76 # define CONFIG_PCI_MEM_SIZE 0x10000000 77 78 # define CONFIG_PCI_IO_BUS 0x50000000 79 # define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS 80 # define CONFIG_PCI_IO_SIZE 0x01000000 81 82 #endif 83 84 /* USB */ 85 #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) 86 87 # define CONFIG_USB_OHCI 88 # define CONFIG_USB_CLOCK 0x0001bbbb 89 # if defined (CONFIG_EVAL5200) 90 # define CONFIG_USB_CONFIG 0x00005100 91 # else 92 # define CONFIG_USB_CONFIG 0x00001000 93 # endif 94 # define CONFIG_DOS_PARTITION 95 # define CONFIG_USB_STORAGE 96 97 #endif 98 99 /* IDE */ 100 #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) 101 # define CONFIG_DOS_PARTITION 102 #endif 103 104 105 /* 106 * BOOTP options 107 */ 108 #define CONFIG_BOOTP_BOOTFILESIZE 109 #define CONFIG_BOOTP_BOOTPATH 110 #define CONFIG_BOOTP_GATEWAY 111 #define CONFIG_BOOTP_HOSTNAME 112 113 114 /* 115 * Command line configuration. 116 */ 117 #include <config_cmd_default.h> 118 119 #define CONFIG_CMD_ASKENV 120 #define CONFIG_CMD_BEDBUG 121 #define CONFIG_CMD_DATE 122 #define CONFIG_CMD_DHCP 123 #define CONFIG_CMD_EEPROM 124 #define CONFIG_CMD_ELF 125 #define CONFIG_CMD_I2C 126 #define CONFIG_CMD_IMMAP 127 #define CONFIG_CMD_MII 128 #define CONFIG_CMD_REGINFO 129 130 #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) 131 #define CONFIG_CMD_FAT 132 #define CONFIG_CMD_IDE 133 #define CONFIG_CMD_USB 134 #define CONFIG_CMD_PCI 135 #endif 136 137 138 /* 139 * MUST be low boot - HIGHBOOT is not supported anymore 140 */ 141 #if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */ 142 # define CONFIG_SYS_LOWBOOT 1 143 # define CONFIG_SYS_LOWBOOT16 1 144 #else 145 # error "TEXT_BASE must be 0xff000000" 146 #endif 147 148 /* 149 * Autobooting 150 */ 151 #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ 152 153 #define CONFIG_PREBOOT "echo;" \ 154 "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ 155 "echo" 156 157 #undef CONFIG_BOOTARGS 158 159 #define CONFIG_EXTRA_ENV_SETTINGS \ 160 "netdev=eth0\0" \ 161 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 162 "nfsroot=${serverip}:${rootpath}\0" \ 163 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 164 "addip=setenv bootargs ${bootargs} " \ 165 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 166 ":${hostname}:${netdev}:off panic=1\0" \ 167 "flash_nfs=run nfsargs addip;" \ 168 "bootm ${kernel_addr}\0" \ 169 "flash_self=run ramargs addip;" \ 170 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 171 "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ 172 "rootpath=/opt/eldk/ppc_82xx\0" \ 173 "bootfile=/tftpboot/MPC5200/uImage\0" \ 174 "" 175 176 #define CONFIG_BOOTCOMMAND "run flash_self" 177 178 /* 179 * IPB Bus clocking configuration. 180 */ 181 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ 182 183 /* 184 * I2C configuration 185 */ 186 /* 187 * EEPROM configuration 188 */ 189 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 190 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 191 192 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 193 #define CONFIG_SYS_EEPROM_SIZE 0x2000 194 195 #define CONFIG_ENV_OVERWRITE 196 #define CONFIG_MISC_INIT_R 197 198 #undef CONFIG_HARD_I2C /* I2C with hardware support */ 199 #define CONFIG_SOFT_I2C 1 /* I2C with softwate support */ 200 201 #if defined (CONFIG_SOFT_I2C) 202 # define SDA0 0x40 203 # define SCL0 0x80 204 # define GPIOE0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c00)) 205 # define DDR0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c08)) 206 # define DVO0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c0c)) 207 # define DVI0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c20)) 208 # define ODE0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c04)) 209 # define I2C_INIT {GPIOE0|=(SDA0|SCL0);ODE0|=(SDA0|SCL0);DVO0|=(SDA0|SCL0);DDR0|=(SDA0|SCL0);} 210 # define I2C_READ ((DVI0&SDA0)?1:0) 211 # define I2C_SDA(x) {if(x)DVO0|=SDA0;else DVO0&=~SDA0;} 212 # define I2C_SCL(x) {if(x)DVO0|=SCL0;else DVO0&=~SCL0;} 213 # define I2C_DELAY {udelay(5);} 214 # define I2C_ACTIVE {DDR0|=SDA0;} 215 # define I2C_TRISTATE {DDR0&=~SDA0;} 216 # define CONFIG_SYS_I2C_SPEED 100000 217 # define CONFIG_SYS_I2C_SLAVE 0x7F 218 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 219 #define CONFIG_SYS_I2C_FACT_ADDR 0x57 220 #endif 221 222 #if defined (CONFIG_HARD_I2C) 223 # define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ 224 # define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ 225 # define CONFIG_SYS_I2C_SLAVE 0x7F 226 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 227 #define CONFIG_SYS_I2C_FACT_ADDR 0x54 228 #endif 229 230 /* 231 * Flash configuration, expect one 16 Megabyte Bank at most 232 */ 233 #define CONFIG_SYS_FLASH_BASE 0xff000000 234 #define CONFIG_SYS_FLASH_SIZE 0x01000000 235 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ 236 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0) 237 238 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ 239 240 #define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ 241 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ 242 243 #undef CONFIG_FLASH_16BIT /* Flash is 8-bit */ 244 245 /* 246 * DRAM configuration - will be read from VPD later... TODO! 247 */ 248 #if 0 249 /* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */ 250 #define CONFIG_SYS_DRAM_DDR 0 251 #define CONFIG_SYS_DRAM_EMODE 0 252 #define CONFIG_SYS_DRAM_MODE 0x008D 253 #define CONFIG_SYS_DRAM_CONTROL 0x514F0000 254 #define CONFIG_SYS_DRAM_CONFIG1 0xC2233A00 255 #define CONFIG_SYS_DRAM_CONFIG2 0x88B70004 256 #define CONFIG_SYS_DRAM_TAP_DEL 0x08 257 #define CONFIG_SYS_DRAM_RAM_SIZE 0x19 258 #endif 259 #if 1 260 /* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */ 261 #define CONFIG_SYS_DRAM_DDR 0 262 #define CONFIG_SYS_DRAM_EMODE 0 263 #define CONFIG_SYS_DRAM_MODE 0x00CD 264 #define CONFIG_SYS_DRAM_CONTROL 0x514F0000 265 #define CONFIG_SYS_DRAM_CONFIG1 0xD2333A00 266 #define CONFIG_SYS_DRAM_CONFIG2 0x8AD70004 267 #define CONFIG_SYS_DRAM_TAP_DEL 0x08 268 #define CONFIG_SYS_DRAM_RAM_SIZE 0x19 269 #endif 270 271 /* 272 * Environment settings 273 */ 274 #define CONFIG_ENV_IS_IN_EEPROM 1 /* turn on EEPROM env feature */ 275 #define CONFIG_ENV_OFFSET 0x1000 276 #define CONFIG_ENV_SIZE 0x0700 277 278 /* 279 * VPD settings 280 */ 281 #define CONFIG_SYS_FACT_OFFSET 0x1800 282 #define CONFIG_SYS_FACT_SIZE 0x0800 283 284 /* 285 * Memory map 286 * 287 * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000 288 */ 289 #define CONFIG_SYS_MBAR 0xf0000000 /* DO NOT CHANGE this */ 290 #define CONFIG_SYS_SDRAM_BASE 0x00000000 291 #define CONFIG_SYS_DEFAULT_MBAR 0x80000000 292 293 /* Use SRAM until RAM will be available */ 294 #define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM 295 #define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ 296 297 298 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ 299 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 300 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 301 302 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE 303 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 304 # define CONFIG_SYS_RAMBOOT 1 305 #endif 306 307 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ 308 #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ 309 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 310 311 /* 312 * Ethernet configuration 313 */ 314 #define CONFIG_MPC5xxx_FEC 1 315 #define CONFIG_MPC5xxx_FEC_MII10 /* Workaround for FEC 100Mbit problem */ 316 #define CONFIG_PHY_ADDR 0x1f 317 #define CONFIG_PHY_TYPE 0x79c874 318 /* 319 * GPIO configuration: 320 * PSC1,2,3 predefined as UART 321 * PCI disabled 322 * Ethernet 100 with MD 323 */ 324 #define CONFIG_SYS_GPS_PORT_CONFIG 0x00058044 325 326 /* 327 * Miscellaneous configurable options 328 */ 329 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 330 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 331 #if defined(CONFIG_CMD_KGDB) 332 # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 333 #else 334 # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 335 #endif 336 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 337 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 338 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 339 340 #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ 341 #define CONFIG_SYS_MEMTEST_END 0x01f00000 /* 1 ... 31 MB in DRAM */ 342 343 #define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */ 344 345 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ 346 347 #define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ 348 #if defined(CONFIG_CMD_KGDB) 349 # define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ 350 #endif 351 352 353 #ifdef CONFIG_EVAL5200 /* M48T08 is available with the Evaluation board only */ 354 #define CONFIG_RTC_MK48T59 1 /* use M48T08 on EVAL5200 */ 355 #define RTC(reg) (0xf0010000+reg) 356 /* setup CS2 for M48T08. Must MAP 64kB */ 357 #define CONFIG_SYS_CS2_START RTC(0) 358 #define CONFIG_SYS_CS2_SIZE 0x10000 359 /* setup CS2 configuration register: */ 360 /* WaitP = 0, WaitX = 4, MX=0, AL=1, AA=1, CE=1 */ 361 /* AS=2, DS=0, Bank=0, WTyp=0, WS=0, RS=0, WO=0, RO=0 */ 362 #define CONFIG_SYS_CS2_CFG 0x00047800 363 #else 364 #define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ 365 #endif 366 367 /* 368 * Various low-level settings 369 */ 370 #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI 371 #define CONFIG_SYS_HID0_FINAL HID0_ICE 372 373 #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE 374 #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE 375 #define CONFIG_SYS_BOOTCS_CFG 0x00047801 376 #define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE 377 #define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE 378 379 #define CONFIG_SYS_CS_BURST 0x00000000 380 #define CONFIG_SYS_CS_DEADCYCLE 0x33333333 381 382 #define CONFIG_SYS_RESET_ADDRESS 0x7f000000 383 384 /*----------------------------------------------------------------------- 385 * IDE/ATA stuff Supports IDE harddisk 386 *----------------------------------------------------------------------- 387 */ 388 389 #undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ 390 391 #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ 392 #undef CONFIG_IDE_LED /* LED for ide not supported */ 393 394 #define CONFIG_IDE_RESET 1 395 #define CONFIG_IDE_PREINIT 396 397 #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ 398 #define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ 399 400 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 401 402 #define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA 403 404 /* Offset for data I/O */ 405 #define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) 406 407 /* Offset for normal register accesses */ 408 #define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) 409 410 /* Offset for alternate registers */ 411 #define CONFIG_SYS_ATA_ALT_OFFSET (0x005c) 412 413 /* Interval between registers */ 414 #define CONFIG_SYS_ATA_STRIDE 4 415 416 #endif /* __CONFIG_H */ 417