1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * PWM device driver for ST SoCs
4 *
5 * Copyright (C) 2013-2016 STMicroelectronics (R&D) Limited
6 *
7 * Author: Ajit Pal Singh <ajitpal.singh@st.com>
8 * Lee Jones <lee.jones@linaro.org>
9 */
10
11 #include <linux/clk.h>
12 #include <linux/interrupt.h>
13 #include <linux/math64.h>
14 #include <linux/mfd/syscon.h>
15 #include <linux/module.h>
16 #include <linux/of.h>
17 #include <linux/platform_device.h>
18 #include <linux/pwm.h>
19 #include <linux/regmap.h>
20 #include <linux/sched.h>
21 #include <linux/slab.h>
22 #include <linux/time.h>
23 #include <linux/wait.h>
24
25 #define PWM_OUT_VAL(x) (0x00 + (4 * (x))) /* Device's Duty Cycle register */
26 #define PWM_CPT_VAL(x) (0x10 + (4 * (x))) /* Capture value */
27 #define PWM_CPT_EDGE(x) (0x30 + (4 * (x))) /* Edge to capture on */
28
29 #define STI_PWM_CTRL 0x50 /* Control/Config register */
30 #define STI_INT_EN 0x54 /* Interrupt Enable/Disable register */
31 #define STI_INT_STA 0x58 /* Interrupt Status register */
32 #define PWM_INT_ACK 0x5c
33 #define PWM_PRESCALE_LOW_MASK 0x0f
34 #define PWM_PRESCALE_HIGH_MASK 0xf0
35 #define PWM_CPT_EDGE_MASK 0x03
36 #define PWM_INT_ACK_MASK 0x1ff
37
38 #define STI_MAX_CPT_DEVS 4
39 #define CPT_DC_MAX 0xff
40
41 /* Regfield IDs */
42 enum {
43 /* Bits in PWM_CTRL*/
44 PWMCLK_PRESCALE_LOW,
45 PWMCLK_PRESCALE_HIGH,
46 CPTCLK_PRESCALE,
47
48 PWM_OUT_EN,
49 PWM_CPT_EN,
50
51 PWM_CPT_INT_EN,
52 PWM_CPT_INT_STAT,
53
54 /* Keep last */
55 MAX_REGFIELDS
56 };
57
58 /*
59 * Each capture input can be programmed to detect rising-edge, falling-edge,
60 * either edge or neither egde.
61 */
62 enum sti_cpt_edge {
63 CPT_EDGE_DISABLED,
64 CPT_EDGE_RISING,
65 CPT_EDGE_FALLING,
66 CPT_EDGE_BOTH,
67 };
68
69 struct sti_cpt_ddata {
70 u32 snapshot[3];
71 unsigned int index;
72 struct mutex lock;
73 wait_queue_head_t wait;
74 };
75
76 struct sti_pwm_compat_data {
77 const struct reg_field *reg_fields;
78 unsigned int pwm_num_devs;
79 unsigned int cpt_num_devs;
80 unsigned int max_pwm_cnt;
81 unsigned int max_prescale;
82 };
83
84 struct sti_pwm_chip {
85 struct device *dev;
86 struct clk *pwm_clk;
87 struct clk *cpt_clk;
88 struct regmap *regmap;
89 struct sti_pwm_compat_data *cdata;
90 struct regmap_field *prescale_low;
91 struct regmap_field *prescale_high;
92 struct regmap_field *pwm_out_en;
93 struct regmap_field *pwm_cpt_en;
94 struct regmap_field *pwm_cpt_int_en;
95 struct regmap_field *pwm_cpt_int_stat;
96 struct pwm_chip chip;
97 struct pwm_device *cur;
98 unsigned long configured;
99 unsigned int en_count;
100 struct mutex sti_pwm_lock; /* To sync between enable/disable calls */
101 void __iomem *mmio;
102 };
103
104 static const struct reg_field sti_pwm_regfields[MAX_REGFIELDS] = {
105 [PWMCLK_PRESCALE_LOW] = REG_FIELD(STI_PWM_CTRL, 0, 3),
106 [PWMCLK_PRESCALE_HIGH] = REG_FIELD(STI_PWM_CTRL, 11, 14),
107 [CPTCLK_PRESCALE] = REG_FIELD(STI_PWM_CTRL, 4, 8),
108 [PWM_OUT_EN] = REG_FIELD(STI_PWM_CTRL, 9, 9),
109 [PWM_CPT_EN] = REG_FIELD(STI_PWM_CTRL, 10, 10),
110 [PWM_CPT_INT_EN] = REG_FIELD(STI_INT_EN, 1, 4),
111 [PWM_CPT_INT_STAT] = REG_FIELD(STI_INT_STA, 1, 4),
112 };
113
to_sti_pwmchip(struct pwm_chip * chip)114 static inline struct sti_pwm_chip *to_sti_pwmchip(struct pwm_chip *chip)
115 {
116 return container_of(chip, struct sti_pwm_chip, chip);
117 }
118
119 /*
120 * Calculate the prescaler value corresponding to the period.
121 */
sti_pwm_get_prescale(struct sti_pwm_chip * pc,unsigned long period,unsigned int * prescale)122 static int sti_pwm_get_prescale(struct sti_pwm_chip *pc, unsigned long period,
123 unsigned int *prescale)
124 {
125 struct sti_pwm_compat_data *cdata = pc->cdata;
126 unsigned long clk_rate;
127 unsigned long value;
128 unsigned int ps;
129
130 clk_rate = clk_get_rate(pc->pwm_clk);
131 if (!clk_rate) {
132 dev_err(pc->dev, "failed to get clock rate\n");
133 return -EINVAL;
134 }
135
136 /*
137 * prescale = ((period_ns * clk_rate) / (10^9 * (max_pwm_cnt + 1)) - 1
138 */
139 value = NSEC_PER_SEC / clk_rate;
140 value *= cdata->max_pwm_cnt + 1;
141
142 if (period % value)
143 return -EINVAL;
144
145 ps = period / value - 1;
146 if (ps > cdata->max_prescale)
147 return -EINVAL;
148
149 *prescale = ps;
150
151 return 0;
152 }
153
154 /*
155 * For STiH4xx PWM IP, the PWM period is fixed to 256 local clock cycles. The
156 * only way to change the period (apart from changing the PWM input clock) is
157 * to change the PWM clock prescaler.
158 *
159 * The prescaler is of 8 bits, so 256 prescaler values and hence 256 possible
160 * period values are supported (for a particular clock rate). The requested
161 * period will be applied only if it matches one of these 256 values.
162 */
sti_pwm_config(struct pwm_chip * chip,struct pwm_device * pwm,int duty_ns,int period_ns)163 static int sti_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
164 int duty_ns, int period_ns)
165 {
166 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
167 struct sti_pwm_compat_data *cdata = pc->cdata;
168 unsigned int ncfg, value, prescale = 0;
169 struct pwm_device *cur = pc->cur;
170 struct device *dev = pc->dev;
171 bool period_same = false;
172 int ret;
173
174 ncfg = hweight_long(pc->configured);
175 if (ncfg)
176 period_same = (period_ns == pwm_get_period(cur));
177
178 /*
179 * Allow configuration changes if one of the following conditions
180 * satisfy.
181 * 1. No devices have been configured.
182 * 2. Only one device has been configured and the new request is for
183 * the same device.
184 * 3. Only one device has been configured and the new request is for
185 * a new device and period of the new device is same as the current
186 * configured period.
187 * 4. More than one devices are configured and period of the new
188 * requestis the same as the current period.
189 */
190 if (!ncfg ||
191 ((ncfg == 1) && (pwm->hwpwm == cur->hwpwm)) ||
192 ((ncfg == 1) && (pwm->hwpwm != cur->hwpwm) && period_same) ||
193 ((ncfg > 1) && period_same)) {
194 /* Enable clock before writing to PWM registers. */
195 ret = clk_enable(pc->pwm_clk);
196 if (ret)
197 return ret;
198
199 ret = clk_enable(pc->cpt_clk);
200 if (ret)
201 return ret;
202
203 if (!period_same) {
204 ret = sti_pwm_get_prescale(pc, period_ns, &prescale);
205 if (ret)
206 goto clk_dis;
207
208 value = prescale & PWM_PRESCALE_LOW_MASK;
209
210 ret = regmap_field_write(pc->prescale_low, value);
211 if (ret)
212 goto clk_dis;
213
214 value = (prescale & PWM_PRESCALE_HIGH_MASK) >> 4;
215
216 ret = regmap_field_write(pc->prescale_high, value);
217 if (ret)
218 goto clk_dis;
219 }
220
221 /*
222 * When PWMVal == 0, PWM pulse = 1 local clock cycle.
223 * When PWMVal == max_pwm_count,
224 * PWM pulse = (max_pwm_count + 1) local cycles,
225 * that is continuous pulse: signal never goes low.
226 */
227 value = cdata->max_pwm_cnt * duty_ns / period_ns;
228
229 ret = regmap_write(pc->regmap, PWM_OUT_VAL(pwm->hwpwm), value);
230 if (ret)
231 goto clk_dis;
232
233 ret = regmap_field_write(pc->pwm_cpt_int_en, 0);
234
235 set_bit(pwm->hwpwm, &pc->configured);
236 pc->cur = pwm;
237
238 dev_dbg(dev, "prescale:%u, period:%i, duty:%i, value:%u\n",
239 prescale, period_ns, duty_ns, value);
240 } else {
241 return -EINVAL;
242 }
243
244 clk_dis:
245 clk_disable(pc->pwm_clk);
246 clk_disable(pc->cpt_clk);
247 return ret;
248 }
249
sti_pwm_enable(struct pwm_chip * chip,struct pwm_device * pwm)250 static int sti_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
251 {
252 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
253 struct device *dev = pc->dev;
254 int ret = 0;
255
256 /*
257 * Since we have a common enable for all PWM devices, do not enable if
258 * already enabled.
259 */
260 mutex_lock(&pc->sti_pwm_lock);
261
262 if (!pc->en_count) {
263 ret = clk_enable(pc->pwm_clk);
264 if (ret)
265 goto out;
266
267 ret = clk_enable(pc->cpt_clk);
268 if (ret)
269 goto out;
270
271 ret = regmap_field_write(pc->pwm_out_en, 1);
272 if (ret) {
273 dev_err(dev, "failed to enable PWM device %u: %d\n",
274 pwm->hwpwm, ret);
275 goto out;
276 }
277 }
278
279 pc->en_count++;
280
281 out:
282 mutex_unlock(&pc->sti_pwm_lock);
283 return ret;
284 }
285
sti_pwm_disable(struct pwm_chip * chip,struct pwm_device * pwm)286 static void sti_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
287 {
288 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
289
290 mutex_lock(&pc->sti_pwm_lock);
291
292 if (--pc->en_count) {
293 mutex_unlock(&pc->sti_pwm_lock);
294 return;
295 }
296
297 regmap_field_write(pc->pwm_out_en, 0);
298
299 clk_disable(pc->pwm_clk);
300 clk_disable(pc->cpt_clk);
301
302 mutex_unlock(&pc->sti_pwm_lock);
303 }
304
sti_pwm_free(struct pwm_chip * chip,struct pwm_device * pwm)305 static void sti_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
306 {
307 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
308
309 clear_bit(pwm->hwpwm, &pc->configured);
310 }
311
sti_pwm_capture(struct pwm_chip * chip,struct pwm_device * pwm,struct pwm_capture * result,unsigned long timeout)312 static int sti_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm,
313 struct pwm_capture *result, unsigned long timeout)
314 {
315 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
316 struct sti_pwm_compat_data *cdata = pc->cdata;
317 struct sti_cpt_ddata *ddata = pwm_get_chip_data(pwm);
318 struct device *dev = pc->dev;
319 unsigned int effective_ticks;
320 unsigned long long high, low;
321 int ret;
322
323 if (pwm->hwpwm >= cdata->cpt_num_devs) {
324 dev_err(dev, "device %u is not valid\n", pwm->hwpwm);
325 return -EINVAL;
326 }
327
328 mutex_lock(&ddata->lock);
329 ddata->index = 0;
330
331 /* Prepare capture measurement */
332 regmap_write(pc->regmap, PWM_CPT_EDGE(pwm->hwpwm), CPT_EDGE_RISING);
333 regmap_field_write(pc->pwm_cpt_int_en, BIT(pwm->hwpwm));
334
335 /* Enable capture */
336 ret = regmap_field_write(pc->pwm_cpt_en, 1);
337 if (ret) {
338 dev_err(dev, "failed to enable PWM capture %u: %d\n",
339 pwm->hwpwm, ret);
340 goto out;
341 }
342
343 ret = wait_event_interruptible_timeout(ddata->wait, ddata->index > 1,
344 msecs_to_jiffies(timeout));
345
346 regmap_write(pc->regmap, PWM_CPT_EDGE(pwm->hwpwm), CPT_EDGE_DISABLED);
347
348 if (ret == -ERESTARTSYS)
349 goto out;
350
351 switch (ddata->index) {
352 case 0:
353 case 1:
354 /*
355 * Getting here could mean:
356 * - input signal is constant of less than 1 Hz
357 * - there is no input signal at all
358 *
359 * In such case the frequency is rounded down to 0
360 */
361 result->period = 0;
362 result->duty_cycle = 0;
363
364 break;
365
366 case 2:
367 /* We have everying we need */
368 high = ddata->snapshot[1] - ddata->snapshot[0];
369 low = ddata->snapshot[2] - ddata->snapshot[1];
370
371 effective_ticks = clk_get_rate(pc->cpt_clk);
372
373 result->period = (high + low) * NSEC_PER_SEC;
374 result->period /= effective_ticks;
375
376 result->duty_cycle = high * NSEC_PER_SEC;
377 result->duty_cycle /= effective_ticks;
378
379 break;
380
381 default:
382 dev_err(dev, "internal error\n");
383 break;
384 }
385
386 out:
387 /* Disable capture */
388 regmap_field_write(pc->pwm_cpt_en, 0);
389
390 mutex_unlock(&ddata->lock);
391 return ret;
392 }
393
394 static const struct pwm_ops sti_pwm_ops = {
395 .capture = sti_pwm_capture,
396 .config = sti_pwm_config,
397 .enable = sti_pwm_enable,
398 .disable = sti_pwm_disable,
399 .free = sti_pwm_free,
400 .owner = THIS_MODULE,
401 };
402
sti_pwm_interrupt(int irq,void * data)403 static irqreturn_t sti_pwm_interrupt(int irq, void *data)
404 {
405 struct sti_pwm_chip *pc = data;
406 struct device *dev = pc->dev;
407 struct sti_cpt_ddata *ddata;
408 int devicenum;
409 unsigned int cpt_int_stat;
410 unsigned int reg;
411 int ret = IRQ_NONE;
412
413 ret = regmap_field_read(pc->pwm_cpt_int_stat, &cpt_int_stat);
414 if (ret)
415 return ret;
416
417 while (cpt_int_stat) {
418 devicenum = ffs(cpt_int_stat) - 1;
419
420 ddata = pwm_get_chip_data(&pc->chip.pwms[devicenum]);
421
422 /*
423 * Capture input:
424 * _______ _______
425 * | | | |
426 * __| |_________________| |________
427 * ^0 ^1 ^2
428 *
429 * Capture start by the first available rising edge. When a
430 * capture event occurs, capture value (CPT_VALx) is stored,
431 * index incremented, capture edge changed.
432 *
433 * After the capture, if the index > 1, we have collected the
434 * necessary data so we signal the thread waiting for it and
435 * disable the capture by setting capture edge to none
436 */
437
438 regmap_read(pc->regmap,
439 PWM_CPT_VAL(devicenum),
440 &ddata->snapshot[ddata->index]);
441
442 switch (ddata->index) {
443 case 0:
444 case 1:
445 regmap_read(pc->regmap, PWM_CPT_EDGE(devicenum), ®);
446 reg ^= PWM_CPT_EDGE_MASK;
447 regmap_write(pc->regmap, PWM_CPT_EDGE(devicenum), reg);
448
449 ddata->index++;
450 break;
451
452 case 2:
453 regmap_write(pc->regmap,
454 PWM_CPT_EDGE(devicenum),
455 CPT_EDGE_DISABLED);
456 wake_up(&ddata->wait);
457 break;
458
459 default:
460 dev_err(dev, "Internal error\n");
461 }
462
463 cpt_int_stat &= ~BIT_MASK(devicenum);
464
465 ret = IRQ_HANDLED;
466 }
467
468 /* Just ACK everything */
469 regmap_write(pc->regmap, PWM_INT_ACK, PWM_INT_ACK_MASK);
470
471 return ret;
472 }
473
sti_pwm_probe_dt(struct sti_pwm_chip * pc)474 static int sti_pwm_probe_dt(struct sti_pwm_chip *pc)
475 {
476 struct device *dev = pc->dev;
477 const struct reg_field *reg_fields;
478 struct device_node *np = dev->of_node;
479 struct sti_pwm_compat_data *cdata = pc->cdata;
480 u32 num_devs;
481 int ret;
482
483 ret = of_property_read_u32(np, "st,pwm-num-chan", &num_devs);
484 if (!ret)
485 cdata->pwm_num_devs = num_devs;
486
487 ret = of_property_read_u32(np, "st,capture-num-chan", &num_devs);
488 if (!ret)
489 cdata->cpt_num_devs = num_devs;
490
491 if (!cdata->pwm_num_devs && !cdata->cpt_num_devs) {
492 dev_err(dev, "No channels configured\n");
493 return -EINVAL;
494 }
495
496 reg_fields = cdata->reg_fields;
497
498 pc->prescale_low = devm_regmap_field_alloc(dev, pc->regmap,
499 reg_fields[PWMCLK_PRESCALE_LOW]);
500 if (IS_ERR(pc->prescale_low))
501 return PTR_ERR(pc->prescale_low);
502
503 pc->prescale_high = devm_regmap_field_alloc(dev, pc->regmap,
504 reg_fields[PWMCLK_PRESCALE_HIGH]);
505 if (IS_ERR(pc->prescale_high))
506 return PTR_ERR(pc->prescale_high);
507
508 pc->pwm_out_en = devm_regmap_field_alloc(dev, pc->regmap,
509 reg_fields[PWM_OUT_EN]);
510 if (IS_ERR(pc->pwm_out_en))
511 return PTR_ERR(pc->pwm_out_en);
512
513 pc->pwm_cpt_en = devm_regmap_field_alloc(dev, pc->regmap,
514 reg_fields[PWM_CPT_EN]);
515 if (IS_ERR(pc->pwm_cpt_en))
516 return PTR_ERR(pc->pwm_cpt_en);
517
518 pc->pwm_cpt_int_en = devm_regmap_field_alloc(dev, pc->regmap,
519 reg_fields[PWM_CPT_INT_EN]);
520 if (IS_ERR(pc->pwm_cpt_int_en))
521 return PTR_ERR(pc->pwm_cpt_int_en);
522
523 pc->pwm_cpt_int_stat = devm_regmap_field_alloc(dev, pc->regmap,
524 reg_fields[PWM_CPT_INT_STAT]);
525 if (PTR_ERR_OR_ZERO(pc->pwm_cpt_int_stat))
526 return PTR_ERR(pc->pwm_cpt_int_stat);
527
528 return 0;
529 }
530
531 static const struct regmap_config sti_pwm_regmap_config = {
532 .reg_bits = 32,
533 .val_bits = 32,
534 .reg_stride = 4,
535 };
536
sti_pwm_probe(struct platform_device * pdev)537 static int sti_pwm_probe(struct platform_device *pdev)
538 {
539 struct device *dev = &pdev->dev;
540 struct sti_pwm_compat_data *cdata;
541 struct sti_pwm_chip *pc;
542 unsigned int i;
543 int irq, ret;
544
545 pc = devm_kzalloc(dev, sizeof(*pc), GFP_KERNEL);
546 if (!pc)
547 return -ENOMEM;
548
549 cdata = devm_kzalloc(dev, sizeof(*cdata), GFP_KERNEL);
550 if (!cdata)
551 return -ENOMEM;
552
553 pc->mmio = devm_platform_ioremap_resource(pdev, 0);
554 if (IS_ERR(pc->mmio))
555 return PTR_ERR(pc->mmio);
556
557 pc->regmap = devm_regmap_init_mmio(dev, pc->mmio,
558 &sti_pwm_regmap_config);
559 if (IS_ERR(pc->regmap))
560 return PTR_ERR(pc->regmap);
561
562 irq = platform_get_irq(pdev, 0);
563 if (irq < 0)
564 return irq;
565
566 ret = devm_request_irq(&pdev->dev, irq, sti_pwm_interrupt, 0,
567 pdev->name, pc);
568 if (ret < 0) {
569 dev_err(&pdev->dev, "Failed to request IRQ\n");
570 return ret;
571 }
572
573 /*
574 * Setup PWM data with default values: some values could be replaced
575 * with specific ones provided from Device Tree.
576 */
577 cdata->reg_fields = sti_pwm_regfields;
578 cdata->max_prescale = 0xff;
579 cdata->max_pwm_cnt = 255;
580 cdata->pwm_num_devs = 0;
581 cdata->cpt_num_devs = 0;
582
583 pc->cdata = cdata;
584 pc->dev = dev;
585 pc->en_count = 0;
586 mutex_init(&pc->sti_pwm_lock);
587
588 ret = sti_pwm_probe_dt(pc);
589 if (ret)
590 return ret;
591
592 if (cdata->pwm_num_devs) {
593 pc->pwm_clk = of_clk_get_by_name(dev->of_node, "pwm");
594 if (IS_ERR(pc->pwm_clk)) {
595 dev_err(dev, "failed to get PWM clock\n");
596 return PTR_ERR(pc->pwm_clk);
597 }
598
599 ret = clk_prepare(pc->pwm_clk);
600 if (ret) {
601 dev_err(dev, "failed to prepare clock\n");
602 return ret;
603 }
604 }
605
606 if (cdata->cpt_num_devs) {
607 pc->cpt_clk = of_clk_get_by_name(dev->of_node, "capture");
608 if (IS_ERR(pc->cpt_clk)) {
609 dev_err(dev, "failed to get PWM capture clock\n");
610 return PTR_ERR(pc->cpt_clk);
611 }
612
613 ret = clk_prepare(pc->cpt_clk);
614 if (ret) {
615 dev_err(dev, "failed to prepare clock\n");
616 return ret;
617 }
618 }
619
620 pc->chip.dev = dev;
621 pc->chip.ops = &sti_pwm_ops;
622 pc->chip.npwm = pc->cdata->pwm_num_devs;
623
624 ret = pwmchip_add(&pc->chip);
625 if (ret < 0) {
626 clk_unprepare(pc->pwm_clk);
627 clk_unprepare(pc->cpt_clk);
628 return ret;
629 }
630
631 for (i = 0; i < cdata->cpt_num_devs; i++) {
632 struct sti_cpt_ddata *ddata;
633
634 ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL);
635 if (!ddata)
636 return -ENOMEM;
637
638 init_waitqueue_head(&ddata->wait);
639 mutex_init(&ddata->lock);
640
641 pwm_set_chip_data(&pc->chip.pwms[i], ddata);
642 }
643
644 platform_set_drvdata(pdev, pc);
645
646 return 0;
647 }
648
sti_pwm_remove(struct platform_device * pdev)649 static int sti_pwm_remove(struct platform_device *pdev)
650 {
651 struct sti_pwm_chip *pc = platform_get_drvdata(pdev);
652
653 pwmchip_remove(&pc->chip);
654
655 clk_unprepare(pc->pwm_clk);
656 clk_unprepare(pc->cpt_clk);
657
658 return 0;
659 }
660
661 static const struct of_device_id sti_pwm_of_match[] = {
662 { .compatible = "st,sti-pwm", },
663 { /* sentinel */ }
664 };
665 MODULE_DEVICE_TABLE(of, sti_pwm_of_match);
666
667 static struct platform_driver sti_pwm_driver = {
668 .driver = {
669 .name = "sti-pwm",
670 .of_match_table = sti_pwm_of_match,
671 },
672 .probe = sti_pwm_probe,
673 .remove = sti_pwm_remove,
674 };
675 module_platform_driver(sti_pwm_driver);
676
677 MODULE_AUTHOR("Ajit Pal Singh <ajitpal.singh@st.com>");
678 MODULE_DESCRIPTION("STMicroelectronics ST PWM driver");
679 MODULE_LICENSE("GPL");
680