1 2EATON-EPDU-MIB DEFINITIONS ::= BEGIN 3 4IMPORTS 5 OBJECT-TYPE, NOTIFICATION-TYPE, MODULE-IDENTITY, 6 Counter32, Unsigned32, Integer32 7 FROM SNMPv2-SMI 8 NOTIFICATION-GROUP, OBJECT-GROUP, MODULE-COMPLIANCE 9 FROM SNMPv2-CONF 10 TEXTUAL-CONVENTION, DateAndTime, DisplayString 11 FROM SNMPv2-TC 12 pduAgent 13 FROM EATON-OIDS; 14 15eatonEpdu MODULE-IDENTITY 16 LAST-UPDATED "201312181200Z" 17 ORGANIZATION 18 "Eaton Corporation" 19 CONTACT-INFO 20 "www.eaton.com/epdu" 21 DESCRIPTION 22 "The MIB module for Eaton ePDUs (Enclosure Power Distribution Units)." 23 24 REVISION "201409291200Z" 25 DESCRIPTION 26 "Added outletControlSwitchable and outletControlShutoffDelay object." 27 28 REVISION "201312181200Z" 29 DESCRIPTION 30 "Added notifyStrappingStatus and strappingStatus object." 31 32 REVISION "201309021200Z" 33 DESCRIPTION 34 "- Add values for commInterface : ftp (4), xml (5)" 35 36 REVISION "201305291200Z" 37 DESCRIPTION 38 "- Edited values for outletType: removed nema51520(21); added nemaL715(29), rf203p277 (30)" 39 40 REVISION "201302211200Z" 41 DESCRIPTION 42 "- Added unit objects : unitType. 43 - Added input objects : inputCurrentCrestFactor, inputCurrentPercentLoad, inputPowerFactor, inputVAR, inputPlugType. 44 - Added gang objects : groupCurrentCrestFactor, groupCurrentPercentLoad, groupPowerFactor, groupVAR. 45 - Added outlet objects : outletCurrentCrestFactor, outletCurrentPercentLoad, outletPowerFactor, outletVAR." 46 47 REVISION "201111211200Z" 48 DESCRIPTION 49 "- Added notifyGroupBreakerStatus object. 50 - Renamed groupStatus object to groupBreakerStatus. This object had not yet 51 been implemented so there is no user impact. 52 - Updated descriptions for inputWhTimer, groupWhTimer, and outletWhTimer." 53 54 REVISION "201110241200Z" 55 DESCRIPTION 56 "- Added notifyBootUp object. 57 - Added outletType object. 58 - Updated description for all lower and upper thresholds to indicate that 59 a value of -1 indicates that it is not supported by a particular ePDU model. 60 - Updated descriptions for inputVA, inputWatts, groupVA, groupWatts, outletVA, 61 outletWatts to indicate that a value of -1 indicates that it is not 62 supported by a particular ePDU model. 63 - Added a note to unit, group, and outlet level control command objects 64 indicating that some products (mainly with part numbers that begin with IPV 65 or IPC) do not support delayed outlet control commands and will reply with 66 an error if a command value is written that is > 0. 67 - Corrected description for inputType. 68 - Added a UnixTimeStamp Textual Convention and changed the SYNTAX of 69 inputWhTimer, groupWhTimer, and outletWhTimer to use it. 70 - Updated the contact info to reference the ePDU website." 71 72 REVISION "201102071529Z" 73 DESCRIPTION 74 "Initial release." 75::= { pduAgent 7 } 76 77 78UnixTimeStamp ::= TEXTUAL-CONVENTION 79 STATUS current 80 DESCRIPTION 81 "Unix time stamp. Measured in seconds since January 1, 1970." 82 SYNTAX Counter32 83 84 85-- eatonEpdu { iso org(3) dod(6) internet(1) private(4) 86-- enterprises(1) eaton(534) products(6) pduAgent(6) (7) } 87 88notifications OBJECT IDENTIFIER ::= { eatonEpdu 0 } 89units OBJECT IDENTIFIER ::= { eatonEpdu 1 } 90inputs OBJECT IDENTIFIER ::= { eatonEpdu 3 } 91groups OBJECT IDENTIFIER ::= { eatonEpdu 5 } 92outlets OBJECT IDENTIFIER ::= { eatonEpdu 6 } 93environmental OBJECT IDENTIFIER ::= { eatonEpdu 7 } 94conformance OBJECT IDENTIFIER ::= { eatonEpdu 25 } 95objectGroups OBJECT IDENTIFIER ::= { conformance 5 } 96 97notifyUserLogin NOTIFICATION-TYPE 98 OBJECTS { userName, 99 commInterface } 100 STATUS current 101 DESCRIPTION 102 "Sent whenever a user logs in." 103 ::= { notifications 1 } 104 105notifyUserLogout NOTIFICATION-TYPE 106 OBJECTS { userName, 107 commInterface } 108 STATUS current 109 DESCRIPTION 110 "Sent whenever a user logs out." 111 ::= { notifications 2 } 112 113notifyFailedLogin NOTIFICATION-TYPE 114 OBJECTS { userName, 115 commInterface } 116 STATUS current 117 DESCRIPTION 118 "Sent when someone attempts to log in and fails. On some models, may be 119 sent after three failed login attempts." 120 ::= { notifications 3 } 121 122notifyBootUp NOTIFICATION-TYPE 123 OBJECTS { strappingIndex } 124 STATUS current 125 DESCRIPTION 126 "Sent whenever an ePDU finishes booting up (hard or soft reboot)." 127 ::= { notifications 4 } 128 129notifyInputVoltageThStatus NOTIFICATION-TYPE 130 OBJECTS { strappingIndex, 131 inputIndex, 132 inputVoltageIndex, 133 inputVoltage, 134 inputVoltageThStatus } 135 STATUS current 136 DESCRIPTION 137 "Sent whenever an input voltage threshold status changes." 138 ::= { notifications 11 } 139 140notifyInputCurrentThStatus NOTIFICATION-TYPE 141 OBJECTS { strappingIndex, 142 inputIndex, 143 inputCurrentIndex, 144 inputCurrent, 145 inputCurrentThStatus } 146 STATUS current 147 DESCRIPTION 148 "Sent whenever an input current threshold status changes." 149 ::= { notifications 12 } 150 151notifyInputFrequencyStatus NOTIFICATION-TYPE 152 OBJECTS { strappingIndex, 153 inputIndex, 154 inputFrequency, 155 inputFrequencyStatus } 156 STATUS current 157 DESCRIPTION 158 "Sent whenever the input frequency status changes." 159 ::= { notifications 13 } 160 161notifyGroupVoltageThStatus NOTIFICATION-TYPE 162 OBJECTS { strappingIndex, 163 groupIndex, 164 groupVoltage, 165 groupVoltageThStatus } 166 STATUS current 167 DESCRIPTION 168 "Sent whenever a group voltage threshold status changes." 169 ::= { notifications 21 } 170 171notifyGroupCurrentThStatus NOTIFICATION-TYPE 172 OBJECTS { strappingIndex, 173 groupIndex, 174 groupCurrent, 175 groupCurrentThStatus } 176 STATUS current 177 DESCRIPTION 178 "Sent whenever a group current threshold status changes." 179 ::= { notifications 22 } 180 181notifyGroupBreakerStatus NOTIFICATION-TYPE 182 OBJECTS { strappingIndex, 183 groupIndex, 184 groupBreakerStatus } 185 STATUS current 186 DESCRIPTION 187 "Sent whenever a group status changes to indicate whether the circuit 188 breaker is on or off." 189 ::= { notifications 23 } 190 191notifyOutletVoltageThStatus NOTIFICATION-TYPE 192 OBJECTS { strappingIndex, 193 outletIndex, 194 outletVoltage, 195 outletVoltageThStatus } 196 STATUS current 197 DESCRIPTION 198 "Sent whenever an outlet voltage threshold status changes." 199 ::= { notifications 31 } 200 201notifyOutletCurrentThStatus NOTIFICATION-TYPE 202 OBJECTS { strappingIndex, 203 outletIndex, 204 outletCurrent, 205 outletCurrentThStatus } 206 STATUS current 207 DESCRIPTION 208 "Sent whenever an outlet current threshold status changes." 209 ::= { notifications 32 } 210 211notifyOutletControlStatus NOTIFICATION-TYPE 212 OBJECTS { strappingIndex, 213 outletIndex, 214 outletControlStatus } 215 STATUS current 216 DESCRIPTION 217 "Sent whenever an outlet state On / Off changes." 218 ::= { notifications 33 } 219 220notifyTemperatureThStatus NOTIFICATION-TYPE 221 OBJECTS { strappingIndex, 222 temperatureIndex, 223 temperatureValue, 224 temperatureThStatus } 225 STATUS current 226 DESCRIPTION 227 "Sent whenever a temperature threshold status changes." 228 ::= { notifications 41 } 229 230notifyHumidityThStatus NOTIFICATION-TYPE 231 OBJECTS { strappingIndex, 232 humidityIndex, 233 humidityValue, 234 humidityThStatus } 235 STATUS current 236 DESCRIPTION 237 "Sent whenever a humidity threshold status changes." 238 ::= { notifications 42 } 239 240notifyContactState NOTIFICATION-TYPE 241 OBJECTS { strappingIndex, 242 contactIndex, 243 contactState } 244 STATUS current 245 DESCRIPTION 246 "Sent whenever a contact sensor state changes." 247 ::= { notifications 43 } 248 249notifyProbeStatus NOTIFICATION-TYPE 250 OBJECTS { strappingIndex, 251 temperatureIndex, 252 temperatureProbeStatus } 253 STATUS current 254 DESCRIPTION 255 "Sent whenever the environment probe status changes." 256 ::= { notifications 44 } 257 258notifyCommunicationStatus NOTIFICATION-TYPE 259 OBJECTS { strappingIndex, 260 communicationStatus } 261 STATUS current 262 DESCRIPTION 263 "Sent whenever the PDU communication status changes." 264 ::= { notifications 51 } 265 266notifyInternalStatus NOTIFICATION-TYPE 267 OBJECTS { strappingIndex, 268 internalStatus } 269 STATUS current 270 DESCRIPTION 271 "Sent whenever the PDU internal status changes." 272 ::= { notifications 52 } 273 274notifyTest NOTIFICATION-TYPE 275 STATUS current 276 DESCRIPTION 277 "Sent whenever the trap test feature is used by the communication card." 278 ::= { notifications 53 } 279 280notifyStrappingStatus NOTIFICATION-TYPE 281 OBJECTS { strappingIndex, 282 strappingStatus } 283 STATUS current 284 DESCRIPTION 285 "Sent whenever the strapping communication status changes." 286 ::= { notifications 54 } 287 288unitsPresent OBJECT-TYPE 289 SYNTAX DisplayString 290 MAX-ACCESS read-only 291 STATUS current 292 DESCRIPTION 293 "Each unit is identified by a Strapping Index. This object returns a comma-delimited list of the 294 Strapping Indexes of all units present in the strapping group. For example, if units 0, 1, 5, 295 and 7 are present, this value will be '0,1,5,7'. For units that do not support strapping, 296 a Strapping Index of '0' is assumed." 297 ::= { units 1 } 298 299unitTable OBJECT-TYPE 300 SYNTAX SEQUENCE OF UnitEntry 301 MAX-ACCESS not-accessible 302 STATUS current 303 DESCRIPTION 304 "A list of units. In most cases this list will only contain one entry. 305 However, some units have a 'strapping' feature which allow units to be 306 daisy-chained together such that all of them can be accessed through 307 the SNMP interface of the master. If strapping is enabled, the 308 strapping indexes of the units that can be accessed will be listed in the 309 unitsPresent object." 310 ::= { units 2 } 311 312unitEntry OBJECT-TYPE 313 SYNTAX UnitEntry 314 MAX-ACCESS not-accessible 315 STATUS current 316 DESCRIPTION 317 "An entry for a PDU." 318 INDEX { strappingIndex } 319 ::= { unitTable 1 } 320 321UnitEntry ::= SEQUENCE { 322 strappingIndex 323 Integer32, 324 productName 325 OCTET STRING, 326 partNumber 327 OCTET STRING, 328 serialNumber 329 OCTET STRING, 330 firmwareVersion 331 OCTET STRING, 332 unitName 333 OCTET STRING, 334 lcdControl 335 INTEGER, 336 clockValue 337 DateAndTime, 338 temperatureScale 339 INTEGER, 340 unitType 341 INTEGER, 342 inputCount 343 Integer32, 344 groupCount 345 Integer32, 346 outletCount 347 Integer32, 348 temperatureCount 349 Integer32, 350 humidityCount 351 Integer32, 352 contactCount 353 Integer32, 354 communicationStatus 355 INTEGER, 356 internalStatus 357 INTEGER, 358 strappingStatus 359 INTEGER, 360 userName 361 OCTET STRING, 362 commInterface 363 INTEGER 364} 365 366strappingIndex OBJECT-TYPE 367 SYNTAX Integer32 (0..23) 368 MAX-ACCESS accessible-for-notify 369 STATUS current 370 DESCRIPTION 371 "For units that support 'strapping' functionality, this will be a unique 372 value for each unit. If units do not support 'strapping', this will 373 always be '0'." 374 ::= { unitEntry 1 } 375 376productName OBJECT-TYPE 377 SYNTAX OCTET STRING (SIZE(1..127)) 378 MAX-ACCESS read-only 379 STATUS current 380 DESCRIPTION 381 "Name of the product." 382 ::= { unitEntry 2 } 383 384partNumber OBJECT-TYPE 385 SYNTAX OCTET STRING 386 MAX-ACCESS read-only 387 STATUS current 388 DESCRIPTION 389 "Part number of the unit." 390 ::= { unitEntry 3 } 391 392serialNumber OBJECT-TYPE 393 SYNTAX OCTET STRING 394 MAX-ACCESS read-only 395 STATUS current 396 DESCRIPTION 397 "Serial number of the unit." 398 ::= { unitEntry 4 } 399 400firmwareVersion OBJECT-TYPE 401 SYNTAX OCTET STRING 402 MAX-ACCESS read-only 403 STATUS current 404 DESCRIPTION 405 "Firmware version." 406 ::= { unitEntry 5 } 407 408unitName OBJECT-TYPE 409 SYNTAX OCTET STRING (SIZE(1..63)) 410 MAX-ACCESS read-write 411 STATUS current 412 DESCRIPTION 413 "Descriptive name for the unit." 414 ::= { unitEntry 6 } 415 416lcdControl OBJECT-TYPE 417 SYNTAX INTEGER { 418 notApplicable (0), 419 lcdScreenOff (1), 420 lcdKeyLock (2), 421 lcdScreenOffAndKeyLock (3) 422 } 423 MAX-ACCESS read-write 424 STATUS current 425 DESCRIPTION 426 "Control the local LCD." 427 ::= { unitEntry 7 } 428 429clockValue OBJECT-TYPE 430 SYNTAX DateAndTime 431 MAX-ACCESS read-write 432 STATUS current 433 DESCRIPTION 434 "Clock value. This could be from either a real-time clock (in which case 435 it is likely writeable) or from a time server via NTP (probably read-only)." 436 ::= { unitEntry 8 } 437 438temperatureScale OBJECT-TYPE 439 SYNTAX INTEGER { 440 celsius (0), 441 fahrenheit (1) 442 } 443 MAX-ACCESS read-write 444 STATUS current 445 DESCRIPTION 446 "Scale used to return temperature objects." 447 ::= { unitEntry 9 } 448 449unitType OBJECT-TYPE 450 SYNTAX INTEGER { 451 unknown (0), 452 switched (1), 453 advancedMonitored (2), 454 managed (3), 455 monitored (4) 456 } 457 MAX-ACCESS read-only 458 STATUS current 459 DESCRIPTION 460 "Technical capabilities of the PDU. Functionality is as follows: 461 Monitored (MI) - input and usually section/group monitoring. 462 Advanced Monitored (AM) - input, section/group, and outlet monitoring. 463 Switched (SW) - input and section/group monitoring, outlet switching. 464 Managed (MA) - input, section/group, and outlet monitoring plug outlet switching." 465 ::= { unitEntry 10 } 466 467inputCount OBJECT-TYPE 468 SYNTAX Integer32 469 MAX-ACCESS read-only 470 STATUS current 471 DESCRIPTION 472 "Number of inputs on this ePDU." 473 ::= { unitEntry 20 } 474 475groupCount OBJECT-TYPE 476 SYNTAX Integer32 477 MAX-ACCESS read-only 478 STATUS current 479 DESCRIPTION 480 "Number of groups on this ePDU. Groups include breakers, outlet sections, 481 and user-defined groups." 482 ::= { unitEntry 21 } 483 484outletCount OBJECT-TYPE 485 SYNTAX Integer32 486 MAX-ACCESS read-only 487 STATUS current 488 DESCRIPTION 489 "Number of outlets on this ePDU." 490 ::= { unitEntry 22 } 491 492temperatureCount OBJECT-TYPE 493 SYNTAX Integer32 494 MAX-ACCESS read-only 495 STATUS current 496 DESCRIPTION 497 "Max number of temperature measurements on this ePDU." 498 ::= { unitEntry 23 } 499 500humidityCount OBJECT-TYPE 501 SYNTAX Integer32 502 MAX-ACCESS read-only 503 STATUS current 504 DESCRIPTION 505 "Max number of humidity measurements on this ePDU." 506 ::= { unitEntry 24 } 507 508contactCount OBJECT-TYPE 509 SYNTAX Integer32 510 MAX-ACCESS read-only 511 STATUS current 512 DESCRIPTION 513 "Max number of contact sensors on this ePDU." 514 ::= { unitEntry 25 } 515 516communicationStatus OBJECT-TYPE 517 SYNTAX INTEGER { 518 good (0), 519 communicationLost (1) 520 } 521 MAX-ACCESS read-only 522 STATUS current 523 DESCRIPTION 524 "Status of the internal communication with the PDU." 525 ::= { unitEntry 30 } 526 527internalStatus OBJECT-TYPE 528 SYNTAX INTEGER { 529 good (0), 530 internalFailure (1) 531 } 532 MAX-ACCESS read-only 533 STATUS current 534 DESCRIPTION 535 "Status of the internal failure inside the PDU." 536 ::= { unitEntry 31 } 537 538strappingStatus OBJECT-TYPE 539 SYNTAX INTEGER { 540 good (0), 541 communicationLost (1) 542 } 543 MAX-ACCESS read-only 544 STATUS current 545 DESCRIPTION 546 "Status of the external communication with a strapping unit." 547 ::= { unitEntry 32 } 548 549userName OBJECT-TYPE 550 SYNTAX OCTET STRING (SIZE(0..31)) 551 MAX-ACCESS accessible-for-notify 552 STATUS current 553 DESCRIPTION 554 "Username used to log into the PDU." 555 ::= { unitEntry 40 } 556 557commInterface OBJECT-TYPE 558 SYNTAX INTEGER { 559 serial (0), 560 usb (1), 561 telnet (2), 562 web (3), 563 ftp (4), 564 xml (5) 565 } 566 MAX-ACCESS accessible-for-notify 567 STATUS current 568 DESCRIPTION 569 "Communications interface used to log into the PDU." 570 ::= { unitEntry 41 } 571 572unitControlTable OBJECT-TYPE 573 SYNTAX SEQUENCE OF UnitControlEntry 574 MAX-ACCESS not-accessible 575 STATUS current 576 DESCRIPTION 577 "A list of units that have controllable outlets." 578 ::= { units 3 } 579 580unitControlEntry OBJECT-TYPE 581 SYNTAX UnitControlEntry 582 MAX-ACCESS not-accessible 583 STATUS current 584 DESCRIPTION 585 "An entry for a PDU which has controllable outlets." 586 INDEX { strappingIndex } 587 ::= { unitControlTable 1 } 588 589UnitControlEntry ::= SEQUENCE { 590 unitControlOffCmd 591 Integer32, 592 unitControlOnCmd 593 Integer32 594} 595 596unitControlOffCmd OBJECT-TYPE 597 SYNTAX Integer32 (-1..99999) 598 MAX-ACCESS read-write 599 STATUS current 600 DESCRIPTION 601 "Unit-level outlet control command. 602 603 Once the command is issued, outlets will turn Off. 604 0-n : Time in seconds until the outlet Sequence Off command is issued 605 -1 : Cancel a pending unit-level Off command 606 607 When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. 608 609 Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control 610 commands. These will respond with an error if a command value of > 0 is written to this object." 611 ::= { unitControlEntry 2 } 612 613unitControlOnCmd OBJECT-TYPE 614 SYNTAX Integer32 (-1..99999) 615 MAX-ACCESS read-write 616 STATUS current 617 DESCRIPTION 618 "Unit-level outlet control command. 619 620 Once the command is issued, outlets will turn On according to their outletControlSequenceDelay value. 621 0-n : Time in seconds until the outlet Sequence On command is issued 622 -1 : Cancel a pending unit-level On command 623 624 When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. 625 626 Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control 627 commands. These will respond with an error if a command value of > 0 is written to this object." 628 ::= { unitControlEntry 3 } 629 630inputTable OBJECT-TYPE 631 SYNTAX SEQUENCE OF InputEntry 632 MAX-ACCESS not-accessible 633 STATUS current 634 DESCRIPTION 635 "List of inputs to the PDU." 636 ::= { inputs 1 } 637 638inputEntry OBJECT-TYPE 639 SYNTAX InputEntry 640 MAX-ACCESS not-accessible 641 STATUS current 642 DESCRIPTION 643 "An entry for a particular input." 644 INDEX { strappingIndex, 645 inputIndex } 646 ::= { inputTable 1 } 647 648InputEntry ::= SEQUENCE { 649 inputIndex 650 Integer32, 651 inputType 652 INTEGER, 653 inputFrequency 654 Integer32, 655 inputFrequencyStatus 656 INTEGER, 657 inputVoltageCount 658 Integer32, 659 inputCurrentCount 660 Integer32, 661 inputPowerCount 662 Integer32, 663 inputPlugType 664 INTEGER 665} 666 667inputIndex OBJECT-TYPE 668 SYNTAX Integer32 (1..2) 669 MAX-ACCESS accessible-for-notify 670 STATUS current 671 DESCRIPTION 672 "A unique value for each input. Its value ranges from 1 to inputCount." 673 ::= { inputEntry 1 } 674 675inputType OBJECT-TYPE 676 SYNTAX INTEGER { 677 singlePhase (1), 678 splitPhase (2), 679 threePhaseDelta (3), 680 threePhaseWye (4) 681 } 682 MAX-ACCESS read-only 683 STATUS current 684 DESCRIPTION 685 "Type of input - single phase, split phase, three phase delta, or three 686 phase wye." 687 ::= { inputEntry 2 } 688 689inputFrequency OBJECT-TYPE 690 SYNTAX Integer32 691 MAX-ACCESS read-only 692 STATUS current 693 DESCRIPTION 694 "Units are 0.1 Hz; divide by ten to get Hz." 695 ::= { inputEntry 3 } 696 697inputFrequencyStatus OBJECT-TYPE 698 SYNTAX INTEGER { 699 good (0), 700 outOfRange (1) 701 } 702 MAX-ACCESS read-only 703 STATUS current 704 DESCRIPTION 705 "Status of the measured input frequency relative to the nominal frequency and the admitted tolerance." 706 ::= { inputEntry 4 } 707 708inputVoltageCount OBJECT-TYPE 709 SYNTAX Integer32 710 MAX-ACCESS read-only 711 STATUS current 712 DESCRIPTION 713 "Number of input voltage measurements on this ePDU." 714 ::= { inputEntry 5 } 715 716inputCurrentCount OBJECT-TYPE 717 SYNTAX Integer32 718 MAX-ACCESS read-only 719 STATUS current 720 DESCRIPTION 721 "Number of input current measurements on this ePDU." 722 ::= { inputEntry 6 } 723 724inputPowerCount OBJECT-TYPE 725 SYNTAX Integer32 726 MAX-ACCESS read-only 727 STATUS current 728 DESCRIPTION 729 "Number of rows in the inputPowerTable." 730 ::= { inputEntry 7 } 731 732inputPlugType OBJECT-TYPE 733 SYNTAX INTEGER { 734 other1Phase (100), 735 other2Phase (200), 736 other3Phase (300), 737 iecC14Inlet (101), 738 iecC20Inlet (102), 739 iec316P6 (103), 740 iec332P6 (104), 741 iec360P6 (105), 742 iecC14Plug (106), 743 iecC20Plug (107), 744 nema515 (120), 745 nemaL515 (121), 746 nema520 (122), 747 nemaL520 (123), 748 nema615 (124), 749 nemaL615 (125), 750 nemaL530 (126), 751 nema620 (127), 752 nemaL620 (128), 753 nemaL630 (129), 754 cs8265 (130), 755 french (150), 756 schuko (151), 757 uk (152), 758 nemaL1420 (201), 759 nemaL1430 (202), 760 iec516P6 (301), 761 iec460P9 (302), 762 iec560P9 (303), 763 iec532P6 (304), 764 iec563P6 (306), 765 nemaL1520 (320), 766 nemaL2120 (321), 767 nemaL1530 (322), 768 nemaL2130 (323), 769 cs8365 (324), 770 nemaL2220 (325), 771 nemaL2230 (326), 772 bladeUps208V (350), 773 bladeUps400V (351) 774 } 775 MAX-ACCESS read-only 776 STATUS current 777 DESCRIPTION 778 "Identifies which plug is on the input." 779 ::= { inputEntry 8 } 780 781inputVoltageTable OBJECT-TYPE 782 SYNTAX SEQUENCE OF InputVoltageEntry 783 MAX-ACCESS not-accessible 784 STATUS current 785 DESCRIPTION 786 "A list of input voltage measurements. The number of entries 787 is given by inputVoltageCount." 788 ::= { inputs 2 } 789 790inputVoltageEntry OBJECT-TYPE 791 SYNTAX InputVoltageEntry 792 MAX-ACCESS not-accessible 793 STATUS current 794 DESCRIPTION 795 "An entry for a particular input voltage measurement." 796 INDEX { strappingIndex, 797 inputIndex, 798 inputVoltageIndex } 799 ::= { inputVoltageTable 1 } 800 801InputVoltageEntry ::= SEQUENCE { 802 inputVoltageIndex 803 Integer32, 804 inputVoltageMeasType 805 INTEGER, 806 inputVoltage 807 Integer32, 808 inputVoltageThStatus 809 INTEGER, 810 inputVoltageThLowerWarning 811 Integer32, 812 inputVoltageThLowerCritical 813 Integer32, 814 inputVoltageThUpperWarning 815 Integer32, 816 inputVoltageThUpperCritical 817 Integer32 818} 819 820inputVoltageIndex OBJECT-TYPE 821 SYNTAX Integer32 (1..3) 822 MAX-ACCESS accessible-for-notify 823 STATUS current 824 DESCRIPTION 825 "A unique value for each input voltage measurement. Its value ranges 826 from 1 to inputVoltageCount." 827 ::= { inputVoltageEntry 1 } 828 829inputVoltageMeasType OBJECT-TYPE 830 SYNTAX INTEGER { 831 singlePhase (1), 832 phase1toN (2), 833 phase2toN (3), 834 phase3toN (4), 835 phase1to2 (5), 836 phase2to3 (6), 837 phase3to1 (7) 838 } 839 MAX-ACCESS read-only 840 STATUS current 841 DESCRIPTION 842 "Value indicates what input voltage is being measured in this table row - single phase 843 voltage, phase 1 to neutral, phase 2 to neutral, phase 3 to neutral, phase 1 to phase 2, 844 phase 2 to phase 3, or phase 3 to phase 1." 845 ::= { inputVoltageEntry 2 } 846 847inputVoltage OBJECT-TYPE 848 SYNTAX Integer32 849 MAX-ACCESS read-only 850 STATUS current 851 DESCRIPTION 852 "An input voltage measurement value. Units are millivolts." 853 ::= { inputVoltageEntry 3 } 854 855inputVoltageThStatus OBJECT-TYPE 856 SYNTAX INTEGER { 857 good (0), 858 lowWarning (1), 859 lowCritical (2), 860 highWarning (3), 861 highCritical (4) 862 } 863 MAX-ACCESS read-only 864 STATUS current 865 DESCRIPTION 866 "Status of the measured input voltage relative to the configured thresholds." 867 ::= { inputVoltageEntry 4 } 868 869inputVoltageThLowerWarning OBJECT-TYPE 870 SYNTAX Integer32 (-1..500000) 871 MAX-ACCESS read-write 872 STATUS current 873 DESCRIPTION 874 "Lower warning threshold. Units are millivolts. A negative value indicates 875 that this object is not available." 876 ::= { inputVoltageEntry 5 } 877 878inputVoltageThLowerCritical OBJECT-TYPE 879 SYNTAX Integer32 (-1..500000) 880 MAX-ACCESS read-write 881 STATUS current 882 DESCRIPTION 883 "Lower critical threshold. Units are millivolts. A negative value indicates 884 that this object is not available." 885 ::= { inputVoltageEntry 6 } 886 887inputVoltageThUpperWarning OBJECT-TYPE 888 SYNTAX Integer32 (-1..500000) 889 MAX-ACCESS read-write 890 STATUS current 891 DESCRIPTION 892 "Upper warning threshold. Units are millivolts. A negative value indicates 893 that this object is not available." 894 ::= { inputVoltageEntry 7 } 895 896inputVoltageThUpperCritical OBJECT-TYPE 897 SYNTAX Integer32 (-1..500000) 898 MAX-ACCESS read-write 899 STATUS current 900 DESCRIPTION 901 "Upper critical threshold. Units are millivolts. A negative value indicates 902 that this object is not available." 903 ::= { inputVoltageEntry 8 } 904 905inputCurrentTable OBJECT-TYPE 906 SYNTAX SEQUENCE OF InputCurrentEntry 907 MAX-ACCESS not-accessible 908 STATUS current 909 DESCRIPTION 910 "A list of input current measurements. The number of entries 911 is given by inputCurrentCount." 912 ::= { inputs 3 } 913 914inputCurrentEntry OBJECT-TYPE 915 SYNTAX InputCurrentEntry 916 MAX-ACCESS not-accessible 917 STATUS current 918 DESCRIPTION 919 "An entry for a particular input current measurement." 920 INDEX { strappingIndex, 921 inputIndex, 922 inputCurrentIndex } 923 ::= { inputCurrentTable 1 } 924 925InputCurrentEntry ::= SEQUENCE { 926 inputCurrentIndex 927 Integer32, 928 inputCurrentMeasType 929 INTEGER, 930 inputCurrentCapacity 931 Integer32, 932 inputCurrent 933 Integer32, 934 inputCurrentThStatus 935 INTEGER, 936 inputCurrentThLowerWarning 937 Integer32, 938 inputCurrentThLowerCritical 939 Integer32, 940 inputCurrentThUpperWarning 941 Integer32, 942 inputCurrentThUpperCritical 943 Integer32, 944 inputCurrentCrestFactor 945 Integer32, 946 inputCurrentPercentLoad 947 Integer32 948} 949 950inputCurrentIndex OBJECT-TYPE 951 SYNTAX Integer32 (1..4) 952 MAX-ACCESS accessible-for-notify 953 STATUS current 954 DESCRIPTION 955 "A unique value for each input current measurement. Its value ranges 956 from 1 to inputCurrentCount." 957 ::= { inputCurrentEntry 1 } 958 959inputCurrentMeasType OBJECT-TYPE 960 SYNTAX INTEGER { 961 singlePhase (1), 962 neutral (2), 963 phase1 (3), 964 phase2 (4), 965 phase3 (5) 966 } 967 MAX-ACCESS read-only 968 STATUS current 969 DESCRIPTION 970 "Which input wire is being measured in this table row - single phase, neutral, phase 1, 971 phase 2, or phase 3." 972 ::= { inputCurrentEntry 2 } 973 974inputCurrentCapacity OBJECT-TYPE 975 SYNTAX Integer32 976 MAX-ACCESS read-only 977 STATUS current 978 DESCRIPTION 979 "Rated current capacity of the input. A negative value indicates that 980 the hardware current capacity is unknown. Units are milliamps." 981 ::= { inputCurrentEntry 3 } 982 983inputCurrent OBJECT-TYPE 984 SYNTAX Integer32 985 MAX-ACCESS read-only 986 STATUS current 987 DESCRIPTION 988 "An input current measurement value. Units are milliamps." 989 ::= { inputCurrentEntry 4 } 990 991inputCurrentThStatus OBJECT-TYPE 992 SYNTAX INTEGER { 993 good (0), 994 lowWarning (1), 995 lowCritical (2), 996 highWarning (3), 997 highCritical (4) 998 } 999 MAX-ACCESS read-only 1000 STATUS current 1001 DESCRIPTION 1002 "Status of the measured input current relative to the configured thresholds." 1003 ::= { inputCurrentEntry 5 } 1004 1005inputCurrentThLowerWarning OBJECT-TYPE 1006 SYNTAX Integer32 (-1..100000) 1007 MAX-ACCESS read-write 1008 STATUS current 1009 DESCRIPTION 1010 "Lower warning threshold. Units are milliamps. A negative value indicates 1011 that this object is not available." 1012 ::= { inputCurrentEntry 6 } 1013 1014inputCurrentThLowerCritical OBJECT-TYPE 1015 SYNTAX Integer32 (-1..100000) 1016 MAX-ACCESS read-write 1017 STATUS current 1018 DESCRIPTION 1019 "Lower critical threshold. Units are milliamps. A negative value indicates 1020 that this object is not available." 1021 ::= { inputCurrentEntry 7 } 1022 1023inputCurrentThUpperWarning OBJECT-TYPE 1024 SYNTAX Integer32 (-1..100000) 1025 MAX-ACCESS read-write 1026 STATUS current 1027 DESCRIPTION 1028 "Upper warning threshold. Units are milliamps. A negative value indicates 1029 that this object is not available." 1030 ::= { inputCurrentEntry 8 } 1031 1032inputCurrentThUpperCritical OBJECT-TYPE 1033 SYNTAX Integer32 (-1..100000) 1034 MAX-ACCESS read-write 1035 STATUS current 1036 DESCRIPTION 1037 "Upper critical threshold. Units are milliamps. A negative value indicates 1038 that this object is not available." 1039 ::= { inputCurrentEntry 9 } 1040 1041inputCurrentCrestFactor OBJECT-TYPE 1042 SYNTAX Integer32 1043 MAX-ACCESS read-only 1044 STATUS current 1045 DESCRIPTION 1046 "Current crest factor. Units are in milli, for example a crest factor of 1047 1.414 will be returned as 1414. A negative value indicates 1048 that this object is not available." 1049 ::= { inputCurrentEntry 10 } 1050 1051inputCurrentPercentLoad OBJECT-TYPE 1052 SYNTAX Integer32 1053 MAX-ACCESS read-only 1054 STATUS current 1055 DESCRIPTION 1056 "Current percent load, based on the rated current capacity. Units are 1057 percentage, for example 80% will be returned as 80. A negative 1058 value indicates that this object is not available." 1059 ::= { inputCurrentEntry 11 } 1060 1061inputPowerTable OBJECT-TYPE 1062 SYNTAX SEQUENCE OF InputPowerEntry 1063 MAX-ACCESS not-accessible 1064 STATUS current 1065 DESCRIPTION 1066 "A list of input power measurements. The number of entries 1067 is given by inputPowerCount." 1068 ::= { inputs 4 } 1069 1070inputPowerEntry OBJECT-TYPE 1071 SYNTAX InputPowerEntry 1072 MAX-ACCESS not-accessible 1073 STATUS current 1074 DESCRIPTION 1075 "An entry for an input power measurement." 1076 INDEX { strappingIndex, 1077 inputIndex, 1078 inputPowerIndex } 1079 ::= { inputPowerTable 1 } 1080 1081InputPowerEntry ::= SEQUENCE { 1082 inputPowerIndex 1083 Integer32, 1084 inputPowerMeasType 1085 INTEGER, 1086 inputVA 1087 Integer32, 1088 inputWatts 1089 Integer32, 1090 inputWh 1091 Unsigned32, 1092 inputWhTimer 1093 UnixTimeStamp, 1094 inputPowerFactor 1095 Integer32, 1096 inputVAR 1097 Integer32 1098} 1099 1100inputPowerIndex OBJECT-TYPE 1101 SYNTAX Integer32 (1..12) 1102 MAX-ACCESS not-accessible 1103 STATUS current 1104 DESCRIPTION 1105 "A unique value for each input power measurement. Its value ranges 1106 from 1 to inputPowerCount." 1107 ::= { inputPowerEntry 1 } 1108 1109inputPowerMeasType OBJECT-TYPE 1110 SYNTAX INTEGER { 1111 unknown (0), 1112 phase1 (1), 1113 phase2 (2), 1114 phase3 (3), 1115 total (4) 1116 } 1117 MAX-ACCESS read-only 1118 STATUS current 1119 DESCRIPTION 1120 "Value indicates what is being measured in this table row." 1121 ::= { inputPowerEntry 2 } 1122 1123inputVA OBJECT-TYPE 1124 SYNTAX Integer32 1125 MAX-ACCESS read-only 1126 STATUS current 1127 DESCRIPTION 1128 "An input VA value. Units are VA. A negative value indicates 1129 that this object is not available." 1130 ::= { inputPowerEntry 3 } 1131 1132inputWatts OBJECT-TYPE 1133 SYNTAX Integer32 1134 MAX-ACCESS read-only 1135 STATUS current 1136 DESCRIPTION 1137 "An input Watts value. Units are Watts. A negative value indicates 1138 that this object is not available." 1139 ::= { inputPowerEntry 4 } 1140 1141inputWh OBJECT-TYPE 1142 SYNTAX Unsigned32 (0..4294967295) 1143 MAX-ACCESS read-write 1144 STATUS current 1145 DESCRIPTION 1146 "Units are Watt-hours. This object is writable so that it can be reset to 0. When it is 1147 written to, the inputWhTimer will be reset updated as well." 1148 ::= { inputPowerEntry 5 } 1149 1150inputWhTimer OBJECT-TYPE 1151 SYNTAX UnixTimeStamp 1152 MAX-ACCESS read-only 1153 STATUS current 1154 DESCRIPTION 1155 "Timestamp of when input Watt-hours (inputWh) was last reset." 1156 ::= { inputPowerEntry 6 } 1157 1158inputPowerFactor OBJECT-TYPE 1159 SYNTAX Integer32 1160 MAX-ACCESS read-only 1161 STATUS current 1162 DESCRIPTION 1163 "An input PF value. Units are in thousandths, for example a power factor 1164 of 0.958 would be returned as 958, and 0.92 would be returned 1165 as 920. A negative value indicates that this object is not 1166 available." 1167 ::= { inputPowerEntry 7 } 1168 1169inputVAR OBJECT-TYPE 1170 SYNTAX Integer32 1171 MAX-ACCESS read-only 1172 STATUS current 1173 DESCRIPTION 1174 "An input VAR value. Units are VAR. A negative value indicates 1175 that this object is not available." 1176 ::= { inputPowerEntry 8 } 1177 1178 1179 1180 1181 1182inputTotalPowerTable OBJECT-TYPE 1183 SYNTAX SEQUENCE OF InputTotalPowerEntry 1184 MAX-ACCESS not-accessible 1185 STATUS current 1186 DESCRIPTION 1187 "A list of total input power measurements." 1188 ::= { inputs 5 } 1189 1190inputTotalPowerEntry OBJECT-TYPE 1191 SYNTAX InputTotalPowerEntry 1192 MAX-ACCESS not-accessible 1193 STATUS current 1194 DESCRIPTION 1195 "An entry for a total input power measurement." 1196 INDEX { strappingIndex, 1197 inputIndex } 1198 ::= { inputTotalPowerTable 1 } 1199 1200InputTotalPowerEntry ::= SEQUENCE { 1201 inputTotalVA 1202 Integer32, 1203 inputTotalWatts 1204 Integer32, 1205 inputTotalWh 1206 Unsigned32, 1207 inputTotalWhTimer 1208 UnixTimeStamp, 1209 inputTotalPowerFactor 1210 Integer32, 1211 inputTotalVAR 1212 Integer32 1213} 1214 1215inputTotalVA OBJECT-TYPE 1216 SYNTAX Integer32 1217 MAX-ACCESS read-only 1218 STATUS current 1219 DESCRIPTION 1220 "An input VA value. Units are VA. A negative value indicates 1221 that this object is not available." 1222 ::= { inputTotalPowerEntry 3 } 1223 1224inputTotalWatts OBJECT-TYPE 1225 SYNTAX Integer32 1226 MAX-ACCESS read-only 1227 STATUS current 1228 DESCRIPTION 1229 "An input Watts value. Units are Watts. A negative value indicates 1230 that this object is not available." 1231 ::= { inputTotalPowerEntry 4 } 1232 1233inputTotalWh OBJECT-TYPE 1234 SYNTAX Unsigned32 (0..4294967295) 1235 MAX-ACCESS read-write 1236 STATUS current 1237 DESCRIPTION 1238 "Units are Watt-hours. This object is writable so that it can be reset to 0. When it is 1239 written to, the inputWhTimer will be reset updated as well." 1240 ::= { inputTotalPowerEntry 5 } 1241 1242inputTotalWhTimer OBJECT-TYPE 1243 SYNTAX UnixTimeStamp 1244 MAX-ACCESS read-only 1245 STATUS current 1246 DESCRIPTION 1247 "Timestamp of when input Watt-hours (inputWh) was last reset." 1248 ::= { inputTotalPowerEntry 6 } 1249 1250inputTotalPowerFactor OBJECT-TYPE 1251 SYNTAX Integer32 1252 MAX-ACCESS read-only 1253 STATUS current 1254 DESCRIPTION 1255 "An input PF value. Units are in thousandths, for example a power factor 1256 of 0.958 would be returned as 958, and 0.92 would be returned 1257 as 920. A negative value indicates that this object is not 1258 available." 1259 ::= { inputTotalPowerEntry 7 } 1260 1261inputTotalVAR OBJECT-TYPE 1262 SYNTAX Integer32 1263 MAX-ACCESS read-only 1264 STATUS current 1265 DESCRIPTION 1266 "An input VAR value. Units are VAR. A negative value indicates 1267 that this object is not available." 1268 ::= { inputTotalPowerEntry 8 } 1269 1270 1271 1272 1273 1274groupTable OBJECT-TYPE 1275 SYNTAX SEQUENCE OF GroupEntry 1276 MAX-ACCESS not-accessible 1277 STATUS current 1278 DESCRIPTION 1279 "A list of groups. The number of entries is given by groupCount." 1280 ::= { groups 1 } 1281 1282groupEntry OBJECT-TYPE 1283 SYNTAX GroupEntry 1284 MAX-ACCESS not-accessible 1285 STATUS current 1286 DESCRIPTION 1287 "An entry for a particular group." 1288 INDEX { strappingIndex, 1289 groupIndex } 1290 ::= { groupTable 1 } 1291 1292GroupEntry ::= SEQUENCE { 1293 groupIndex 1294 Integer32, 1295 groupID 1296 DisplayString, 1297 groupName 1298 OCTET STRING, 1299 groupType 1300 INTEGER, 1301 groupBreakerStatus 1302 INTEGER, 1303 groupChildCount 1304 Integer32 1305} 1306 1307groupIndex OBJECT-TYPE 1308 SYNTAX Integer32 (1..64) 1309 MAX-ACCESS accessible-for-notify 1310 STATUS current 1311 DESCRIPTION 1312 "A unique value for each group. Its value ranges from 1 to groupCount." 1313 ::= { groupEntry 1 } 1314 1315groupID OBJECT-TYPE 1316 SYNTAX DisplayString (SIZE(2..4)) 1317 MAX-ACCESS read-only 1318 STATUS current 1319 DESCRIPTION 1320 "Alphanumeric designator for the group. This value may be written 1321 on the face of the unit." 1322 ::= { groupEntry 2 } 1323 1324groupName OBJECT-TYPE 1325 SYNTAX OCTET STRING (SIZE(1..31)) 1326 MAX-ACCESS read-write 1327 STATUS current 1328 DESCRIPTION 1329 "A descriptive name for the group." 1330 ::= { groupEntry 3 } 1331 1332groupType OBJECT-TYPE 1333 SYNTAX INTEGER { 1334 unknown (0), 1335 breaker1pole (1), 1336 breaker2pole (2), 1337 breaker3pole (3), 1338 outletSection (4), 1339 userDefined (5) 1340 } 1341 MAX-ACCESS read-only 1342 STATUS current 1343 DESCRIPTION 1344 "The type of the group." 1345 ::= { groupEntry 4 } 1346 1347groupBreakerStatus OBJECT-TYPE 1348 SYNTAX INTEGER { 1349 notApplicable (0), 1350 breakerOn (1), 1351 breakerOff (2) 1352 } 1353 MAX-ACCESS read-only 1354 STATUS current 1355 DESCRIPTION 1356 "Only applicable to breaker-groups. Indicates whether a breaker is turned 1357 off or on." 1358 ::= { groupEntry 5 } 1359 1360groupChildCount OBJECT-TYPE 1361 SYNTAX Integer32 1362 MAX-ACCESS read-only 1363 STATUS current 1364 DESCRIPTION 1365 "Number of children for this group." 1366 ::= { groupEntry 6 } 1367 1368groupChildTable OBJECT-TYPE 1369 SYNTAX SEQUENCE OF GroupChildEntry 1370 MAX-ACCESS not-accessible 1371 STATUS current 1372 DESCRIPTION 1373 "A list of children for this group. For example, this table will link 1374 to all of the outlets that are contained in a particular group." 1375 ::= { groups 2 } 1376 1377groupChildEntry OBJECT-TYPE 1378 SYNTAX GroupChildEntry 1379 MAX-ACCESS not-accessible 1380 STATUS current 1381 DESCRIPTION 1382 "An entry for a particular child." 1383 INDEX { strappingIndex, 1384 groupIndex, 1385 groupChildIndex } 1386 ::= { groupChildTable 1 } 1387 1388GroupChildEntry ::= SEQUENCE { 1389 groupChildIndex 1390 Integer32, 1391 groupChildType 1392 INTEGER, 1393 groupChildOID 1394 OBJECT IDENTIFIER 1395} 1396 1397groupChildIndex OBJECT-TYPE 1398 SYNTAX Integer32 (1..32) 1399 MAX-ACCESS not-accessible 1400 STATUS current 1401 DESCRIPTION 1402 "A unique value for each child. Its value ranges from 1 to groupChildCount." 1403 ::= { groupChildEntry 1 } 1404 1405groupChildType OBJECT-TYPE 1406 SYNTAX INTEGER { 1407 unknown (0), 1408 section (2), 1409 custom (3), 1410 outlet (4) 1411 } 1412 MAX-ACCESS read-only 1413 STATUS current 1414 DESCRIPTION 1415 "The type of the child." 1416 ::= { groupChildEntry 2 } 1417 1418groupChildOID OBJECT-TYPE 1419 SYNTAX OBJECT IDENTIFIER 1420 MAX-ACCESS read-only 1421 STATUS current 1422 DESCRIPTION 1423 "Object ID of a child object." 1424 ::= { groupChildEntry 3 } 1425 1426groupVoltageTable OBJECT-TYPE 1427 SYNTAX SEQUENCE OF GroupVoltageEntry 1428 MAX-ACCESS not-accessible 1429 STATUS current 1430 DESCRIPTION 1431 "A list of group voltage measurements. There can be only one voltage 1432 measurement for each group." 1433 ::= { groups 3 } 1434 1435groupVoltageEntry OBJECT-TYPE 1436 SYNTAX GroupVoltageEntry 1437 MAX-ACCESS not-accessible 1438 STATUS current 1439 DESCRIPTION 1440 "An entry for a group voltage measurement." 1441 INDEX { strappingIndex, 1442 groupIndex } 1443 ::= { groupVoltageTable 1 } 1444 1445GroupVoltageEntry ::= SEQUENCE { 1446 groupVoltageMeasType 1447 INTEGER, 1448 groupVoltage 1449 Integer32, 1450 groupVoltageThStatus 1451 INTEGER, 1452 groupVoltageThLowerWarning 1453 Integer32, 1454 groupVoltageThLowerCritical 1455 Integer32, 1456 groupVoltageThUpperWarning 1457 Integer32, 1458 groupVoltageThUpperCritical 1459 Integer32 1460} 1461 1462groupVoltageMeasType OBJECT-TYPE 1463 SYNTAX INTEGER { 1464 unknown (0), 1465 singlePhase (1), 1466 phase1toN (2), 1467 phase2toN (3), 1468 phase3toN (4), 1469 phase1to2 (5), 1470 phase2to3 (6), 1471 phase3to1 (7) 1472 } 1473 MAX-ACCESS read-only 1474 STATUS current 1475 DESCRIPTION 1476 "Value indicates what voltage is being measured in this table row." 1477 ::= { groupVoltageEntry 2 } 1478 1479groupVoltage OBJECT-TYPE 1480 SYNTAX Integer32 1481 MAX-ACCESS read-only 1482 STATUS current 1483 DESCRIPTION 1484 "Units are millivolts." 1485 ::= { groupVoltageEntry 3 } 1486 1487groupVoltageThStatus OBJECT-TYPE 1488 SYNTAX INTEGER { 1489 good (0), 1490 lowWarning (1), 1491 lowCritical (2), 1492 highWarning (3), 1493 highCritical (4) 1494 } 1495 MAX-ACCESS read-only 1496 STATUS current 1497 DESCRIPTION 1498 "Status of the measured group voltage relative to the configured thresholds." 1499 ::= { groupVoltageEntry 4 } 1500 1501groupVoltageThLowerWarning OBJECT-TYPE 1502 SYNTAX Integer32 (-1..500000) 1503 MAX-ACCESS read-write 1504 STATUS current 1505 DESCRIPTION 1506 "Lower warning threshold. Units are millivolts. A negative value indicates 1507 that this object is not available." 1508 ::= { groupVoltageEntry 5 } 1509 1510groupVoltageThLowerCritical OBJECT-TYPE 1511 SYNTAX Integer32 (-1..500000) 1512 MAX-ACCESS read-write 1513 STATUS current 1514 DESCRIPTION 1515 "Lower critical threshold. Units are millivolts. A negative value indicates 1516 that this object is not available." 1517 ::= { groupVoltageEntry 6 } 1518 1519groupVoltageThUpperWarning OBJECT-TYPE 1520 SYNTAX Integer32 (-1..500000) 1521 MAX-ACCESS read-write 1522 STATUS current 1523 DESCRIPTION 1524 "Upper warning threshold. Units are millivolts. A negative value indicates 1525 that this object is not available." 1526 ::= { groupVoltageEntry 7 } 1527 1528groupVoltageThUpperCritical OBJECT-TYPE 1529 SYNTAX Integer32 (-1..500000) 1530 MAX-ACCESS read-write 1531 STATUS current 1532 DESCRIPTION 1533 "Upper critical threshold. Units are millivolts. A negative value indicates 1534 that this object is not available." 1535 ::= { groupVoltageEntry 8 } 1536 1537groupCurrentTable OBJECT-TYPE 1538 SYNTAX SEQUENCE OF GroupCurrentEntry 1539 MAX-ACCESS not-accessible 1540 STATUS current 1541 DESCRIPTION 1542 "A list of group current measurements. There can be only one current 1543 measurement for each group." 1544 ::= { groups 4 } 1545 1546groupCurrentEntry OBJECT-TYPE 1547 SYNTAX GroupCurrentEntry 1548 MAX-ACCESS not-accessible 1549 STATUS current 1550 DESCRIPTION 1551 "An entry for a group current measurement." 1552 INDEX { strappingIndex, 1553 groupIndex } 1554 ::= { groupCurrentTable 1 } 1555 1556GroupCurrentEntry ::= SEQUENCE { 1557 groupCurrentCapacity 1558 Integer32, 1559 groupCurrent 1560 Integer32, 1561 groupCurrentThStatus 1562 INTEGER, 1563 groupCurrentThLowerWarning 1564 Integer32, 1565 groupCurrentThLowerCritical 1566 Integer32, 1567 groupCurrentThUpperWarning 1568 Integer32, 1569 groupCurrentThUpperCritical 1570 Integer32, 1571 groupCurrentCrestFactor 1572 Integer32, 1573 groupCurrentPercentLoad 1574 Integer32 1575} 1576 1577groupCurrentCapacity OBJECT-TYPE 1578 SYNTAX Integer32 1579 MAX-ACCESS read-only 1580 STATUS current 1581 DESCRIPTION 1582 "Rated current capacity of the group. Units are milliamps. A negative 1583 value indicates that the hardware current capacity is unknown (it 1584 will always be unknown for custom groups)." 1585 ::= { groupCurrentEntry 2 } 1586 1587groupCurrent OBJECT-TYPE 1588 SYNTAX Integer32 1589 MAX-ACCESS read-only 1590 STATUS current 1591 DESCRIPTION 1592 "A group current measurement value. Units are milliamps." 1593 ::= { groupCurrentEntry 3 } 1594 1595groupCurrentThStatus OBJECT-TYPE 1596 SYNTAX INTEGER { 1597 good (0), 1598 lowWarning (1), 1599 lowCritical (2), 1600 highWarning (3), 1601 highCritical (4) 1602 } 1603 MAX-ACCESS read-only 1604 STATUS current 1605 DESCRIPTION 1606 "Status of the measured group current relative to the configured thresholds." 1607 ::= { groupCurrentEntry 4 } 1608 1609groupCurrentThLowerWarning OBJECT-TYPE 1610 SYNTAX Integer32 (-1..100000) 1611 MAX-ACCESS read-write 1612 STATUS current 1613 DESCRIPTION 1614 "Lower warning threshold. Units are milliamps. A negative value indicates 1615 that this object is not available." 1616 ::= { groupCurrentEntry 5 } 1617 1618groupCurrentThLowerCritical OBJECT-TYPE 1619 SYNTAX Integer32 (-1..100000) 1620 MAX-ACCESS read-write 1621 STATUS current 1622 DESCRIPTION 1623 "Lower critical threshold. Units are milliamps. A negative value indicates 1624 that this object is not available." 1625 ::= { groupCurrentEntry 6 } 1626 1627groupCurrentThUpperWarning OBJECT-TYPE 1628 SYNTAX Integer32 (-1..100000) 1629 MAX-ACCESS read-write 1630 STATUS current 1631 DESCRIPTION 1632 "Upper warning threshold. Units are milliamps. A negative value indicates 1633 that this object is not available." 1634 ::= { groupCurrentEntry 7 } 1635 1636groupCurrentThUpperCritical OBJECT-TYPE 1637 SYNTAX Integer32 (-1..100000) 1638 MAX-ACCESS read-write 1639 STATUS current 1640 DESCRIPTION 1641 "Upper critical threshold. Units are milliamps. A negative value indicates 1642 that this object is not available." 1643 ::= { groupCurrentEntry 8 } 1644 1645groupCurrentCrestFactor OBJECT-TYPE 1646 SYNTAX Integer32 1647 MAX-ACCESS read-only 1648 STATUS current 1649 DESCRIPTION 1650 "Current crest factor. Units are in milli, for example a crest factor of 1651 1.414 will be returned as 1414. A negative value indicates 1652 that this object is not available." 1653 ::= { groupCurrentEntry 9 } 1654 1655groupCurrentPercentLoad OBJECT-TYPE 1656 SYNTAX Integer32 1657 MAX-ACCESS read-only 1658 STATUS current 1659 DESCRIPTION 1660 "Current percent load, based on the rated current capacity. Units are 1661 percentage, for example 80% will be returned as 80. A negative 1662 value indicates that this object is not available." 1663 ::= { groupCurrentEntry 10 } 1664 1665groupPowerTable OBJECT-TYPE 1666 SYNTAX SEQUENCE OF GroupPowerEntry 1667 MAX-ACCESS not-accessible 1668 STATUS current 1669 DESCRIPTION 1670 "A list of group power measurements. There can be only one power 1671 measurement for each group." 1672 ::= { groups 5 } 1673 1674groupPowerEntry OBJECT-TYPE 1675 SYNTAX GroupPowerEntry 1676 MAX-ACCESS not-accessible 1677 STATUS current 1678 DESCRIPTION 1679 "An entry for a group power measurement." 1680 INDEX { strappingIndex, 1681 groupIndex } 1682 ::= { groupPowerTable 1 } 1683 1684GroupPowerEntry ::= SEQUENCE { 1685 groupVA 1686 Integer32, 1687 groupWatts 1688 Integer32, 1689 groupWh 1690 Unsigned32, 1691 groupWhTimer 1692 UnixTimeStamp, 1693 groupPowerFactor 1694 Integer32, 1695 groupVAR 1696 Integer32 1697} 1698 1699groupVA OBJECT-TYPE 1700 SYNTAX Integer32 1701 MAX-ACCESS read-only 1702 STATUS current 1703 DESCRIPTION 1704 "A group VA value. Units are VA. A negative value indicates 1705 that this object is not available." 1706 ::= { groupPowerEntry 2 } 1707 1708groupWatts OBJECT-TYPE 1709 SYNTAX Integer32 1710 MAX-ACCESS read-only 1711 STATUS current 1712 DESCRIPTION 1713 "A group Watts value. Units are Watts. A negative value indicates 1714 that this object is not available." 1715 ::= { groupPowerEntry 3 } 1716 1717groupWh OBJECT-TYPE 1718 SYNTAX Unsigned32 (0..4294967295) 1719 MAX-ACCESS read-write 1720 STATUS current 1721 DESCRIPTION 1722 "Units are Watt-hours. This object is writable so that it can be reset to 0. When it is 1723 written to, the inputWhTotalTimer will be reset to 0 as well." 1724 ::= { groupPowerEntry 4 } 1725 1726groupWhTimer OBJECT-TYPE 1727 SYNTAX UnixTimeStamp 1728 MAX-ACCESS read-only 1729 STATUS current 1730 DESCRIPTION 1731 "Timestamp of when group Watt-hours (groupWh) was last reset." 1732 ::= { groupPowerEntry 5 } 1733 1734groupPowerFactor OBJECT-TYPE 1735 SYNTAX Integer32 1736 MAX-ACCESS read-only 1737 STATUS current 1738 DESCRIPTION 1739 "A group PF value. Units are in thousandths, for example a power factor 1740 of 0.958 would be returned as 958, and 0.92 would be returned 1741 as 920. A negative value indicates that this object is not available." 1742 ::= { groupPowerEntry 6 } 1743 1744groupVAR OBJECT-TYPE 1745 SYNTAX Integer32 1746 MAX-ACCESS read-only 1747 STATUS current 1748 DESCRIPTION 1749 "A group VAR value. Units are VAR. A negative value indicates 1750 that this object is not available." 1751 ::= { groupPowerEntry 7 } 1752 1753groupControlTable OBJECT-TYPE 1754 SYNTAX SEQUENCE OF GroupControlEntry 1755 MAX-ACCESS not-accessible 1756 STATUS current 1757 DESCRIPTION 1758 "A list of controllable groups." 1759 ::= { groups 6 } 1760 1761groupControlEntry OBJECT-TYPE 1762 SYNTAX GroupControlEntry 1763 MAX-ACCESS not-accessible 1764 STATUS current 1765 DESCRIPTION 1766 "An entry for a controllable group." 1767 INDEX { strappingIndex, 1768 groupIndex } 1769 ::= { groupControlTable 1 } 1770 1771GroupControlEntry ::= SEQUENCE { 1772 groupControlStatus 1773 INTEGER, 1774 groupControlOffCmd 1775 Integer32, 1776 groupControl0nCmd 1777 Integer32, 1778 groupControlRebootCmd 1779 Integer32 1780} 1781 1782groupControlStatus OBJECT-TYPE 1783 SYNTAX INTEGER { 1784 off (0), 1785 on (1), 1786 rebooting (2), 1787 mixed (3) 1788 } 1789 MAX-ACCESS read-only 1790 STATUS current 1791 DESCRIPTION 1792 "Current state of a controlled group. A value of 'mixed' means that 1793 that the outlets within the group have differing states." 1794 ::= { groupControlEntry 2 } 1795 1796groupControlOffCmd OBJECT-TYPE 1797 SYNTAX Integer32 (-1..99999) 1798 MAX-ACCESS read-write 1799 STATUS current 1800 DESCRIPTION 1801 "Group-level outlet control command. 1802 1803 Once the command is issued, the outlets in the group will turn Off immediately. 1804 0-n : Time in seconds until the group command is issued 1805 -1 : Cancel a pending group-level Off command 1806 1807 When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. 1808 1809 Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control 1810 commands. These will respond with an error if a command value of > 0 is written to this object." 1811 ::= { groupControlEntry 3 } 1812 1813groupControl0nCmd OBJECT-TYPE 1814 SYNTAX Integer32 (-1..99999) 1815 MAX-ACCESS read-write 1816 STATUS current 1817 DESCRIPTION 1818 "Group-level outlet control command. 1819 1820 Once the command is issued, the outlets in the group will turn On immediately. 1821 0-n : Time in seconds until the group command is issued 1822 -1 : Cancel a pending group-level On command 1823 1824 When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. 1825 1826 Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control 1827 commands. These will respond with an error if a command value of > 0 is written to this object." 1828 ::= { groupControlEntry 4 } 1829 1830groupControlRebootCmd OBJECT-TYPE 1831 SYNTAX Integer32 (-1..0) 1832 MAX-ACCESS read-write 1833 STATUS current 1834 DESCRIPTION 1835 "Group-level outlet control command. 1836 1837 For outlets that are On prior to the Reboot command, they will switch Off immediately when the command is 1838 issued, remain Off for outletControlRebootOffTime seconds, and then turn back On. 1839 For outlets that are Off prior to the Reboot command, they will turn On after a delay of outletControlRebootOffTime 1840 seconds from when the command is issued. 1841 0-n : Time in seconds until the Reboot command is issued 1842 -1 : Cancel a pending group-level Reboot command 1843 1844 When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. 1845 1846 Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control 1847 commands. These will respond with an error if a command value of > 0 is written to this object." 1848 ::= { groupControlEntry 5 } 1849 1850outletTable OBJECT-TYPE 1851 SYNTAX SEQUENCE OF OutletEntry 1852 MAX-ACCESS not-accessible 1853 STATUS current 1854 DESCRIPTION 1855 "A list of outlets. The number of entries is given by outletCount." 1856 ::= { outlets 1 } 1857 1858outletEntry OBJECT-TYPE 1859 SYNTAX OutletEntry 1860 MAX-ACCESS not-accessible 1861 STATUS current 1862 DESCRIPTION 1863 "An entry for a particular outlet." 1864 INDEX { strappingIndex, 1865 outletIndex } 1866 ::= { outletTable 1 } 1867 1868OutletEntry ::= SEQUENCE { 1869 outletIndex 1870 Integer32, 1871 outletID 1872 DisplayString, 1873 outletName 1874 OCTET STRING, 1875 outletParentCount 1876 Integer32, 1877 outletType 1878 INTEGER 1879} 1880 1881outletIndex OBJECT-TYPE 1882 SYNTAX Integer32 (1..64) 1883 MAX-ACCESS accessible-for-notify 1884 STATUS current 1885 DESCRIPTION 1886 "A unique value for each outlet. its value ranges from 1 to outletCount." 1887 ::= { outletEntry 1 } 1888 1889outletID OBJECT-TYPE 1890 SYNTAX DisplayString (SIZE(2..4)) 1891 MAX-ACCESS read-only 1892 STATUS current 1893 DESCRIPTION 1894 "Alphanumeric designator for the outlet." 1895 ::= { outletEntry 2 } 1896 1897outletName OBJECT-TYPE 1898 SYNTAX OCTET STRING (SIZE(1..31)) 1899 MAX-ACCESS read-write 1900 STATUS current 1901 DESCRIPTION 1902 "A descriptive name for the outlet." 1903 ::= { outletEntry 3 } 1904 1905outletParentCount OBJECT-TYPE 1906 SYNTAX Integer32 1907 MAX-ACCESS read-only 1908 STATUS current 1909 DESCRIPTION 1910 "Number of parents for this outlet." 1911 ::= { outletEntry 4 } 1912 1913outletType OBJECT-TYPE 1914 SYNTAX INTEGER { 1915 unknown (0), 1916 iecC13 (1), 1917 iecC19 (2), 1918 uk (10), 1919 french (11), 1920 schuko (12), 1921 nema515 (20), 1922 nema51520 (21), 1923 nema520 (22), 1924 nemaL520 (23), 1925 nemaL530 (24), 1926 nema615 (25), 1927 nema620 (26), 1928 nemaL620 (27), 1929 nemaL630 (28), 1930 nemaL715 (29), 1931 rf203p277 (30) 1932 } 1933 MAX-ACCESS read-only 1934 STATUS current 1935 DESCRIPTION 1936 "The physical type of outlet." 1937 ::= { outletEntry 5 } 1938 1939outletParentTable OBJECT-TYPE 1940 SYNTAX SEQUENCE OF OutletParentEntry 1941 MAX-ACCESS not-accessible 1942 STATUS current 1943 DESCRIPTION 1944 "A list of parents for this outlet. For example, this table will link 1945 to all of the groups that have this outlet as a child." 1946 ::= { outlets 2 } 1947 1948outletParentEntry OBJECT-TYPE 1949 SYNTAX OutletParentEntry 1950 MAX-ACCESS not-accessible 1951 STATUS current 1952 DESCRIPTION 1953 "An entry for a particular parent." 1954 INDEX { strappingIndex, 1955 outletIndex, 1956 outletParentIndex } 1957 ::= { outletParentTable 1 } 1958 1959OutletParentEntry ::= SEQUENCE { 1960 outletParentIndex 1961 Integer32, 1962 outletParentType 1963 INTEGER, 1964 outletParentOID 1965 OBJECT IDENTIFIER 1966} 1967 1968outletParentIndex OBJECT-TYPE 1969 SYNTAX Integer32 (1..32) 1970 MAX-ACCESS not-accessible 1971 STATUS current 1972 DESCRIPTION 1973 "A unique value for each parent. Its value ranges from 1 to outletParentCount." 1974 ::= { outletParentEntry 1 } 1975 1976outletParentType OBJECT-TYPE 1977 SYNTAX INTEGER { 1978 unknown (0), 1979 breaker (1), 1980 section (2), 1981 custom (3) 1982 } 1983 MAX-ACCESS read-only 1984 STATUS current 1985 DESCRIPTION 1986 "The type of the parent." 1987 ::= { outletParentEntry 2 } 1988 1989outletParentOID OBJECT-TYPE 1990 SYNTAX OBJECT IDENTIFIER 1991 MAX-ACCESS read-only 1992 STATUS current 1993 DESCRIPTION 1994 "Object ID of a parent object." 1995 ::= { outletParentEntry 3 } 1996 1997outletVoltageTable OBJECT-TYPE 1998 SYNTAX SEQUENCE OF OutletVoltageEntry 1999 MAX-ACCESS not-accessible 2000 STATUS current 2001 DESCRIPTION 2002 "A list of outlet voltage measurements." 2003 ::= { outlets 3 } 2004 2005outletVoltageEntry OBJECT-TYPE 2006 SYNTAX OutletVoltageEntry 2007 MAX-ACCESS not-accessible 2008 STATUS current 2009 DESCRIPTION 2010 "An entry for an outlet voltage measurement." 2011 INDEX { strappingIndex, 2012 outletIndex } 2013 ::= { outletVoltageTable 1 } 2014 2015OutletVoltageEntry ::= SEQUENCE { 2016 outletVoltage 2017 Integer32, 2018 outletVoltageThStatus 2019 INTEGER, 2020 outletVoltageThLowerWarning 2021 Integer32, 2022 outletVoltageThLowerCritical 2023 Integer32, 2024 outletVoltageThUpperWarning 2025 Integer32, 2026 outletVoltageThUpperCritical 2027 Integer32 2028} 2029 2030outletVoltage OBJECT-TYPE 2031 SYNTAX Integer32 2032 MAX-ACCESS read-only 2033 STATUS current 2034 DESCRIPTION 2035 "Units are millivolts." 2036 ::= { outletVoltageEntry 2 } 2037 2038outletVoltageThStatus OBJECT-TYPE 2039 SYNTAX INTEGER { 2040 good (0), 2041 lowWarning (1), 2042 lowCritical (2), 2043 highWarning (3), 2044 highCritical (4) 2045 } 2046 MAX-ACCESS read-only 2047 STATUS current 2048 DESCRIPTION 2049 "Status of the measured outlet voltage relative to the configured thresholds." 2050 ::= { outletVoltageEntry 3 } 2051 2052outletVoltageThLowerWarning OBJECT-TYPE 2053 SYNTAX Integer32 (-1..500000) 2054 MAX-ACCESS read-write 2055 STATUS current 2056 DESCRIPTION 2057 "Lower warning threshold. Units are millivolts. A negative value indicates 2058 that this object is not available." 2059 ::= { outletVoltageEntry 4 } 2060 2061outletVoltageThLowerCritical OBJECT-TYPE 2062 SYNTAX Integer32 (-1..500000) 2063 MAX-ACCESS read-write 2064 STATUS current 2065 DESCRIPTION 2066 "Lower critical threshold. Units are millivolts. A negative value indicates 2067 that this object is not available." 2068 ::= { outletVoltageEntry 5 } 2069 2070outletVoltageThUpperWarning OBJECT-TYPE 2071 SYNTAX Integer32 (-1..500000) 2072 MAX-ACCESS read-write 2073 STATUS current 2074 DESCRIPTION 2075 "Upper warning threshold. Units are millivolts. A negative value indicates 2076 that this object is not available." 2077 ::= { outletVoltageEntry 6 } 2078 2079outletVoltageThUpperCritical OBJECT-TYPE 2080 SYNTAX Integer32 (-1..500000) 2081 MAX-ACCESS read-write 2082 STATUS current 2083 DESCRIPTION 2084 "Upper critical threshold. Units are millivolts. A negative value indicates 2085 that this object is not available." 2086 ::= { outletVoltageEntry 7 } 2087 2088outletCurrentTable OBJECT-TYPE 2089 SYNTAX SEQUENCE OF OutletCurrentEntry 2090 MAX-ACCESS not-accessible 2091 STATUS current 2092 DESCRIPTION 2093 "A list of outlet current measurements." 2094 ::= { outlets 4 } 2095 2096outletCurrentEntry OBJECT-TYPE 2097 SYNTAX OutletCurrentEntry 2098 MAX-ACCESS not-accessible 2099 STATUS current 2100 DESCRIPTION 2101 "An entry for an outlet current measurement." 2102 INDEX { strappingIndex, 2103 outletIndex } 2104 ::= { outletCurrentTable 1 } 2105 2106OutletCurrentEntry ::= SEQUENCE { 2107 outletCurrentCapacity 2108 Integer32, 2109 outletCurrent 2110 Integer32, 2111 outletCurrentThStatus 2112 INTEGER, 2113 outletCurrentThLowerWarning 2114 Integer32, 2115 outletCurrentThLowerCritical 2116 Integer32, 2117 outletCurrentThUpperWarning 2118 Integer32, 2119 outletCurrentThUpperCritical 2120 Integer32, 2121 outletCurrentCrestFactor 2122 Integer32, 2123 outletCurrentPercentLoad 2124 Integer32 2125} 2126 2127outletCurrentCapacity OBJECT-TYPE 2128 SYNTAX Integer32 2129 MAX-ACCESS read-only 2130 STATUS current 2131 DESCRIPTION 2132 "Rated current capacity of the outlet. Units are milliamps. A negative 2133 value indicates that the hardware current capacity is unknown." 2134 ::= { outletCurrentEntry 2 } 2135 2136outletCurrent OBJECT-TYPE 2137 SYNTAX Integer32 2138 MAX-ACCESS read-only 2139 STATUS current 2140 DESCRIPTION 2141 "An outlet current measurement value. Units are milliamps." 2142 ::= { outletCurrentEntry 3 } 2143 2144outletCurrentThStatus OBJECT-TYPE 2145 SYNTAX INTEGER { 2146 good (0), 2147 lowWarning (1), 2148 lowCritical (2), 2149 highWarning (3), 2150 highCritical (4) 2151 } 2152 MAX-ACCESS read-only 2153 STATUS current 2154 DESCRIPTION 2155 "Status of the measured outlet current relative to the configured thresholds." 2156 ::= { outletCurrentEntry 4 } 2157 2158outletCurrentThLowerWarning OBJECT-TYPE 2159 SYNTAX Integer32 (-1..100000) 2160 MAX-ACCESS read-write 2161 STATUS current 2162 DESCRIPTION 2163 "Lower warning threshold. Units are milliamps. A negative value indicates 2164 that this object is not available." 2165 ::= { outletCurrentEntry 5 } 2166 2167outletCurrentThLowerCritical OBJECT-TYPE 2168 SYNTAX Integer32 (-1..100000) 2169 MAX-ACCESS read-write 2170 STATUS current 2171 DESCRIPTION 2172 "Lower critical threshold. Units are milliamps. A negative value indicates 2173 that this object is not available." 2174 ::= { outletCurrentEntry 6 } 2175 2176outletCurrentThUpperWarning OBJECT-TYPE 2177 SYNTAX Integer32 (-1..100000) 2178 MAX-ACCESS read-write 2179 STATUS current 2180 DESCRIPTION 2181 "Upper warning threshold. Units are milliamps. A negative value indicates 2182 that this object is not available." 2183 ::= { outletCurrentEntry 7 } 2184 2185outletCurrentThUpperCritical OBJECT-TYPE 2186 SYNTAX Integer32 (-1..100000) 2187 MAX-ACCESS read-write 2188 STATUS current 2189 DESCRIPTION 2190 "Upper critical threshold. Units are milliamps. A negative value indicates 2191 that this object is not available." 2192 ::= { outletCurrentEntry 8 } 2193 2194outletCurrentCrestFactor OBJECT-TYPE 2195 SYNTAX Integer32 2196 MAX-ACCESS read-only 2197 STATUS current 2198 DESCRIPTION 2199 "Current crest factor. Units are in milli, for example a crest factor of 2200 1.414 will be returned as 1414. A negative value indicates 2201 that this object is not available." 2202 ::= { outletCurrentEntry 9 } 2203 2204outletCurrentPercentLoad OBJECT-TYPE 2205 SYNTAX Integer32 2206 MAX-ACCESS read-only 2207 STATUS current 2208 DESCRIPTION 2209 "Current percent load, based on the rated current capacity. Units are 2210 percentage, for example 80% will be returned as 80. A negative 2211 value indicates that this object is not available." 2212 ::= { outletCurrentEntry 10 } 2213 2214outletPowerTable OBJECT-TYPE 2215 SYNTAX SEQUENCE OF OutletPowerEntry 2216 MAX-ACCESS not-accessible 2217 STATUS current 2218 DESCRIPTION 2219 "A list of outlet power measurements." 2220 ::= { outlets 5 } 2221 2222outletPowerEntry OBJECT-TYPE 2223 SYNTAX OutletPowerEntry 2224 MAX-ACCESS not-accessible 2225 STATUS current 2226 DESCRIPTION 2227 "An entry for an outlet power measurement." 2228 INDEX { strappingIndex, 2229 outletIndex } 2230 ::= { outletPowerTable 1 } 2231 2232OutletPowerEntry ::= SEQUENCE { 2233 outletVA 2234 Integer32, 2235 outletWatts 2236 Integer32, 2237 outletWh 2238 Unsigned32, 2239 outletWhTimer 2240 UnixTimeStamp, 2241 outletPowerFactor 2242 Integer32, 2243 outletVAR 2244 Integer32 2245} 2246 2247outletVA OBJECT-TYPE 2248 SYNTAX Integer32 2249 MAX-ACCESS read-only 2250 STATUS current 2251 DESCRIPTION 2252 "An outlet VA value. Units are VA. A negative value indicates 2253 that this object is not available." 2254 ::= { outletPowerEntry 2 } 2255 2256outletWatts OBJECT-TYPE 2257 SYNTAX Integer32 2258 MAX-ACCESS read-only 2259 STATUS current 2260 DESCRIPTION 2261 "An outlet Watts value. Units are Watts. A negative value indicates 2262 that this object is not available." 2263 ::= { outletPowerEntry 3 } 2264 2265outletWh OBJECT-TYPE 2266 SYNTAX Unsigned32 (0..4294967295) 2267 MAX-ACCESS read-write 2268 STATUS current 2269 DESCRIPTION 2270 "Units are Watt-hours. This object is writable so that it can be reset to 0. When it is 2271 written to, the inputWhTotalTimer will be reset to 0 as well." 2272 ::= { outletPowerEntry 4 } 2273 2274outletWhTimer OBJECT-TYPE 2275 SYNTAX UnixTimeStamp 2276 MAX-ACCESS read-only 2277 STATUS current 2278 DESCRIPTION 2279 "Timestamp of when outlet Watt-hours (outletWh) was last reset." 2280 ::= { outletPowerEntry 5 } 2281 2282outletPowerFactor OBJECT-TYPE 2283 SYNTAX Integer32 2284 MAX-ACCESS read-only 2285 STATUS current 2286 DESCRIPTION 2287 "An outlet PF value. Units are in thousandths, for example a power factor 2288 of 0.958 would be returned as 958, and 0.92 would be returned 2289 as 920. A negative value indicates that this object is not available." 2290 ::= { outletPowerEntry 6 } 2291 2292outletVAR OBJECT-TYPE 2293 SYNTAX Integer32 2294 MAX-ACCESS read-only 2295 STATUS current 2296 DESCRIPTION 2297 "An outlet VAR value. Units are VAR. A negative value indicates 2298 that this object is not available." 2299 ::= { outletPowerEntry 7 } 2300 2301outletControlTable OBJECT-TYPE 2302 SYNTAX SEQUENCE OF OutletControlEntry 2303 MAX-ACCESS not-accessible 2304 STATUS current 2305 DESCRIPTION 2306 "A list of controllable outlets." 2307 ::= { outlets 6 } 2308 2309outletControlEntry OBJECT-TYPE 2310 SYNTAX OutletControlEntry 2311 MAX-ACCESS not-accessible 2312 STATUS current 2313 DESCRIPTION 2314 "An entry for a controllable outlet." 2315 INDEX { strappingIndex, 2316 outletIndex } 2317 ::= { outletControlTable 1 } 2318 2319OutletControlEntry ::= SEQUENCE { 2320 outletControlStatus 2321 INTEGER, 2322 outletControlOffCmd 2323 Integer32, 2324 outletControlOnCmd 2325 Integer32, 2326 outletControlRebootCmd 2327 Integer32, 2328 outletControlPowerOnState 2329 INTEGER, 2330 outletControlSequenceDelay 2331 Integer32, 2332 outletControlRebootOffTime 2333 Integer32, 2334 outletControlSwitchable 2335 INTEGER, 2336 outletControlShutoffDelay 2337 Integer32 2338} 2339 2340outletControlStatus OBJECT-TYPE 2341 SYNTAX INTEGER { 2342 off (0), 2343 on (1), 2344 pendingOff (2), 2345 pendingOn (3) 2346 } 2347 MAX-ACCESS read-only 2348 STATUS current 2349 DESCRIPTION 2350 "Current state of a controlled outlet." 2351 ::= { outletControlEntry 2 } 2352 2353outletControlOffCmd OBJECT-TYPE 2354 SYNTAX Integer32 (-1..99999) 2355 MAX-ACCESS read-write 2356 STATUS current 2357 DESCRIPTION 2358 "Outlet control command. 2359 2360 Once the command is issued, the outlet will turn Off immediately. 2361 0-n : Time in seconds until the outlet command is issued 2362 -1 : Cancel a pending outlet Off command 2363 2364 When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. 2365 2366 Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control 2367 commands. These will respond with an error if a command value of > 0 is written to this object." 2368 ::= { outletControlEntry 3 } 2369 2370outletControlOnCmd OBJECT-TYPE 2371 SYNTAX Integer32 (-1..99999) 2372 MAX-ACCESS read-write 2373 STATUS current 2374 DESCRIPTION 2375 "Outlet control command. 2376 2377 Once the command is issued, the outlet will turn On immediately. 2378 0-n : Time in seconds until the outlet command is issued 2379 -1 : Cancel a pending outlet On command 2380 2381 When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. 2382 2383 Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control 2384 commands. These will respond with an error if a command value of > 0 is written to this object." 2385 ::= { outletControlEntry 4 } 2386 2387outletControlRebootCmd OBJECT-TYPE 2388 SYNTAX Integer32 (-1..99999) 2389 MAX-ACCESS read-write 2390 STATUS current 2391 DESCRIPTION 2392 "Outlet control command. 2393 2394 For outlets that are On prior to this Reboot command, they will switch Off immediately when the command is 2395 issued, remain Off for outletControlRebootOffTime seconds, and then turn back On. 2396 For outlets that are Off prior to the Reboot command, they will turn On after a delay of outletControlRebootOffTime 2397 seconds from when the command is issued. 2398 0-n : Time in seconds until the Reboot command is issued 2399 -1 : Cancel a pending outlet Reboot command 2400 2401 When read, returns -1 if no command is pending, or the current downcount in seconds of a pending command. 2402 2403 Certain ePDUs (mainly those with part numbers beginning with IPV or IPC) do not support delayed control 2404 commands. These will respond with an error if a command value of > 0 is written to this object." 2405 ::= { outletControlEntry 5 } 2406 2407outletControlPowerOnState OBJECT-TYPE 2408 SYNTAX INTEGER { 2409 off (0), 2410 on (1), 2411 lastState (2) 2412 } 2413 MAX-ACCESS read-write 2414 STATUS current 2415 DESCRIPTION 2416 "Determines the outlet state when power is applied to the unit. 2417 0 : not restart at device startup 2418 1 : should sequence back ON in line with outletControlSequenceTime 2419 2 : should take the state the outlet had when power was lost. 2420 If the state was ON, should sequence back ON in line with outletControlSequenceTime." 2421 ::= { outletControlEntry 6 } 2422 2423outletControlSequenceDelay OBJECT-TYPE 2424 SYNTAX Integer32 (-1..99999) 2425 MAX-ACCESS read-write 2426 STATUS current 2427 DESCRIPTION 2428 "Time delay in seconds from when a Global Sequence On command is issued to 2429 when the command is executed on this outlet. This delay is also used as a power-on 2430 delay. Set to -1 to exclude this outlet from Global Sequence On 2431 commands." 2432 ::= { outletControlEntry 7 } 2433 2434outletControlRebootOffTime OBJECT-TYPE 2435 SYNTAX Integer32 (1..99999) 2436 MAX-ACCESS read-write 2437 STATUS current 2438 DESCRIPTION 2439 "Time delay in seconds that the outlet should remain in the Off state when executing a Reboot command." 2440 ::= { outletControlEntry 8 } 2441 2442outletControlSwitchable OBJECT-TYPE 2443 SYNTAX INTEGER { 2444 switchable (1), 2445 notSwitchable (2) 2446 } 2447 MAX-ACCESS read-write 2448 STATUS current 2449 DESCRIPTION 2450 "Determines the outlet capability to be controlled On/Off from the communication channels. 2451 1 : control On/Off enabled 2452 2 : control On/Off disabled." 2453 ::= { outletControlEntry 9 } 2454 2455outletControlShutoffDelay OBJECT-TYPE 2456 SYNTAX Integer32 (-1..99999) 2457 MAX-ACCESS read-write 2458 STATUS current 2459 DESCRIPTION 2460 "Time delay in seconds that could be taken in account before shutting of the outlet. 2461 An application which need to shutoff properly an outlet will read this parameter first 2462 then write it to the command outletControlOffCmd." 2463 ::= { outletControlEntry 10 } 2464 2465temperatureTable OBJECT-TYPE 2466 SYNTAX SEQUENCE OF TemperatureEntry 2467 MAX-ACCESS not-accessible 2468 STATUS current 2469 DESCRIPTION 2470 "A list of temperature probe measurements. The number of entries is 2471 given by temperatureCount." 2472 ::= { environmental 1 } 2473 2474temperatureEntry OBJECT-TYPE 2475 SYNTAX TemperatureEntry 2476 MAX-ACCESS not-accessible 2477 STATUS current 2478 DESCRIPTION 2479 "An entry for a temperature measurement." 2480 INDEX { strappingIndex, 2481 temperatureIndex } 2482 ::= { temperatureTable 1 } 2483 2484TemperatureEntry ::= SEQUENCE { 2485 temperatureIndex 2486 Integer32, 2487 temperatureName 2488 OCTET STRING, 2489 temperatureProbeStatus 2490 INTEGER, 2491 temperatureValue 2492 Integer32, 2493 temperatureThStatus 2494 INTEGER, 2495 temperatureThLowerWarning 2496 Integer32, 2497 temperatureThLowerCritical 2498 Integer32, 2499 temperatureThUpperWarning 2500 Integer32, 2501 temperatureThUpperCritical 2502 Integer32 2503} 2504 2505temperatureIndex OBJECT-TYPE 2506 SYNTAX Integer32 (1..2) 2507 MAX-ACCESS accessible-for-notify 2508 STATUS current 2509 DESCRIPTION 2510 "A unique value for each temperature probe measurement. Its value 2511 ranges from 1 to temperatureCount." 2512 ::= { temperatureEntry 1 } 2513 2514temperatureName OBJECT-TYPE 2515 SYNTAX OCTET STRING (SIZE(1..31)) 2516 MAX-ACCESS read-write 2517 STATUS current 2518 DESCRIPTION 2519 "A descriptive name for the temperature probe." 2520 ::= { temperatureEntry 2 } 2521 2522temperatureProbeStatus OBJECT-TYPE 2523 SYNTAX INTEGER { 2524 bad (-1), 2525 disconnected (0), 2526 connected (1) 2527 } 2528 MAX-ACCESS read-only 2529 STATUS current 2530 DESCRIPTION 2531 "Indicates whether a probe is connected or not." 2532 ::= { temperatureEntry 3 } 2533 2534temperatureValue OBJECT-TYPE 2535 SYNTAX Integer32 2536 MAX-ACCESS read-only 2537 STATUS current 2538 DESCRIPTION 2539 "Units are in tenths of a degree according to the scale specified by 2540 temperatureScale (either Fahrenheit or Celsius). Divide by ten to get 2541 degrees." 2542 ::= { temperatureEntry 4 } 2543 2544temperatureThStatus OBJECT-TYPE 2545 SYNTAX INTEGER { 2546 good (0), 2547 lowWarning (1), 2548 lowCritical (2), 2549 highWarning (3), 2550 highCritical (4) 2551 } 2552 MAX-ACCESS read-only 2553 STATUS current 2554 DESCRIPTION 2555 "Status of the measured temperature relative to the configured 2556 thresholds." 2557 ::= { temperatureEntry 5 } 2558 2559temperatureThLowerWarning OBJECT-TYPE 2560 SYNTAX Integer32 (-1..150000) 2561 MAX-ACCESS read-write 2562 STATUS current 2563 DESCRIPTION 2564 "Lower warning threshold. Units are tenths of a degree. A negative value 2565 indicates that this object is not available." 2566 ::= { temperatureEntry 6 } 2567 2568temperatureThLowerCritical OBJECT-TYPE 2569 SYNTAX Integer32 (-1..150000) 2570 MAX-ACCESS read-write 2571 STATUS current 2572 DESCRIPTION 2573 "Lower critical threshold. Units are tenths of a degree. A negative value 2574 indicates that this object is not available." 2575 ::= { temperatureEntry 7 } 2576 2577temperatureThUpperWarning OBJECT-TYPE 2578 SYNTAX Integer32 (-1..150000) 2579 MAX-ACCESS read-write 2580 STATUS current 2581 DESCRIPTION 2582 "Upper warning threshold. Units are tenths of a degree. A negative value 2583 indicates that this object is not available." 2584 ::= { temperatureEntry 8 } 2585 2586temperatureThUpperCritical OBJECT-TYPE 2587 SYNTAX Integer32 (-1..150000) 2588 MAX-ACCESS read-write 2589 STATUS current 2590 DESCRIPTION 2591 "Upper critical threshold. Units are tenths of a degree. A negative value 2592 indicates that this object is not available." 2593 ::= { temperatureEntry 9 } 2594 2595humidityTable OBJECT-TYPE 2596 SYNTAX SEQUENCE OF HumidityEntry 2597 MAX-ACCESS not-accessible 2598 STATUS current 2599 DESCRIPTION 2600 "A list of humidity probe measurements. The number of entries is 2601 given by humidityCount." 2602 ::= { environmental 2 } 2603 2604humidityEntry OBJECT-TYPE 2605 SYNTAX HumidityEntry 2606 MAX-ACCESS not-accessible 2607 STATUS current 2608 DESCRIPTION 2609 "An entry for a humidity measurement." 2610 INDEX { strappingIndex, 2611 humidityIndex } 2612 ::= { humidityTable 1 } 2613 2614HumidityEntry ::= SEQUENCE { 2615 humidityIndex 2616 Integer32, 2617 humidityName 2618 OCTET STRING, 2619 humidityProbeStatus 2620 INTEGER, 2621 humidityValue 2622 Integer32, 2623 humidityThStatus 2624 INTEGER, 2625 humidityThLowerWarning 2626 Integer32, 2627 humidityThLowerCritical 2628 Integer32, 2629 humidityThUpperWarning 2630 Integer32, 2631 humidityThUpperCritical 2632 Integer32 2633} 2634 2635humidityIndex OBJECT-TYPE 2636 SYNTAX Integer32 (1..2) 2637 MAX-ACCESS accessible-for-notify 2638 STATUS current 2639 DESCRIPTION 2640 "A unique value for each humidity probe measurement. Its value 2641 ranges from 1 to humidityCount." 2642 ::= { humidityEntry 1 } 2643 2644humidityName OBJECT-TYPE 2645 SYNTAX OCTET STRING (SIZE(1..31)) 2646 MAX-ACCESS read-write 2647 STATUS current 2648 DESCRIPTION 2649 "A descriptive name for the humidity probe." 2650 ::= { humidityEntry 2 } 2651 2652humidityProbeStatus OBJECT-TYPE 2653 SYNTAX INTEGER { 2654 bad (-1), 2655 disconnected (0), 2656 connected (1) 2657 } 2658 MAX-ACCESS read-only 2659 STATUS current 2660 DESCRIPTION 2661 "Indicates whether a probe is connected or not." 2662 ::= { humidityEntry 3 } 2663 2664humidityValue OBJECT-TYPE 2665 SYNTAX Integer32 2666 MAX-ACCESS read-only 2667 STATUS current 2668 DESCRIPTION 2669 "Units are tenths of a percent relative humidity. Divide the value by 10 to get %RH." 2670 ::= { humidityEntry 4 } 2671 2672humidityThStatus OBJECT-TYPE 2673 SYNTAX INTEGER { 2674 good (0), 2675 lowWarning (1), 2676 lowCritical (2), 2677 highWarning (3), 2678 highCritical (4) 2679 } 2680 MAX-ACCESS read-only 2681 STATUS current 2682 DESCRIPTION 2683 "Status of the measured humidity relative to the configured 2684 thresholds." 2685 ::= { humidityEntry 5 } 2686 2687humidityThLowerWarning OBJECT-TYPE 2688 SYNTAX Integer32 (-1..1000) 2689 MAX-ACCESS read-write 2690 STATUS current 2691 DESCRIPTION 2692 "Lower warning threshold. Units are 0.1 %RH. A negative value 2693 indicates that this object is not available." 2694 ::= { humidityEntry 6 } 2695 2696humidityThLowerCritical OBJECT-TYPE 2697 SYNTAX Integer32 (-1..1000) 2698 MAX-ACCESS read-write 2699 STATUS current 2700 DESCRIPTION 2701 "Lower critical threshold. Units are 0.1 %RH. A negative value 2702 indicates that this object is not available." 2703 ::= { humidityEntry 7 } 2704 2705humidityThUpperWarning OBJECT-TYPE 2706 SYNTAX Integer32 (-1..1000) 2707 MAX-ACCESS read-write 2708 STATUS current 2709 DESCRIPTION 2710 "Upper warning threshold. Units are 0.1 %RH. A negative value 2711 indicates that this object is not available." 2712 ::= { humidityEntry 8 } 2713 2714humidityThUpperCritical OBJECT-TYPE 2715 SYNTAX Integer32 (-1..1000) 2716 MAX-ACCESS read-write 2717 STATUS current 2718 DESCRIPTION 2719 "Upper critical threshold. Units are 0.1 %RH. A negative value 2720 indicates that this object is not available." 2721 ::= { humidityEntry 9 } 2722 2723contactTable OBJECT-TYPE 2724 SYNTAX SEQUENCE OF ContactEntry 2725 MAX-ACCESS not-accessible 2726 STATUS current 2727 DESCRIPTION 2728 "A list of contact sensors. The number of entries is 2729 given by contactCount." 2730 ::= { environmental 3 } 2731 2732contactEntry OBJECT-TYPE 2733 SYNTAX ContactEntry 2734 MAX-ACCESS not-accessible 2735 STATUS current 2736 DESCRIPTION 2737 "An entry for a contact sensor" 2738 INDEX { strappingIndex, 2739 contactIndex } 2740 ::= { contactTable 1 } 2741 2742ContactEntry ::= SEQUENCE { 2743 contactIndex 2744 Integer32, 2745 contactName 2746 OCTET STRING, 2747 contactProbeStatus 2748 INTEGER, 2749 contactState 2750 INTEGER 2751} 2752 2753contactIndex OBJECT-TYPE 2754 SYNTAX Integer32 (1..3) 2755 MAX-ACCESS accessible-for-notify 2756 STATUS current 2757 DESCRIPTION 2758 "A unique value for each contact sensor. Its value ranges from 1 to 2759 contactCount." 2760 ::= { contactEntry 1 } 2761 2762contactName OBJECT-TYPE 2763 SYNTAX OCTET STRING (SIZE(1..31)) 2764 MAX-ACCESS read-write 2765 STATUS current 2766 DESCRIPTION 2767 "A descriptive name for the contact sensor." 2768 ::= { contactEntry 2 } 2769 2770contactProbeStatus OBJECT-TYPE 2771 SYNTAX INTEGER { 2772 bad (-1), 2773 disconnected (0), 2774 connected (1) 2775 } 2776 MAX-ACCESS read-only 2777 STATUS current 2778 DESCRIPTION 2779 "Indicates whether a probe is connected or not. 2780 Will not be returned if the contact sensor is internal to the ePDU, 2781 in that case only contactState should be read." 2782 ::= { contactEntry 3 } 2783 2784contactState OBJECT-TYPE 2785 SYNTAX INTEGER { 2786 contactBad (-1), 2787 contactOpen (0), 2788 contactClosed (1) 2789 } 2790 MAX-ACCESS read-only 2791 STATUS current 2792 DESCRIPTION 2793 "The state of the contact sensor." 2794 ::= { contactEntry 4 } 2795 2796eatonEpduCompliances MODULE-COMPLIANCE 2797 STATUS current 2798 DESCRIPTION 2799 "The requirements for conforming to the ePDU MIB." 2800 MODULE 2801 MANDATORY-GROUPS { epduRequiredGroup } 2802 GROUP epduOptionalGroup 2803 DESCRIPTION 2804 "Different ePDUs will support a subset of the defined objects." 2805 GROUP epduNotifyGroup 2806 DESCRIPTION 2807 "Different ePDUs will support a subset of the defined notifications." 2808 ::= { conformance 1 } 2809 2810epduRequiredGroup OBJECT-GROUP 2811 OBJECTS { unitName, 2812 firmwareVersion } 2813 STATUS current 2814 DESCRIPTION 2815 "Minimal objects are required to conform to this MIB." 2816 ::= { objectGroups 1 } 2817 2818epduOptionalGroup OBJECT-GROUP 2819 OBJECTS { clockValue, 2820 commInterface, 2821 communicationStatus, 2822 contactCount, 2823 contactIndex, 2824 contactName, 2825 contactProbeStatus, 2826 contactState, 2827 groupChildCount, 2828 groupChildOID, 2829 groupChildType, 2830 groupControl0nCmd, 2831 groupControlOffCmd, 2832 groupControlRebootCmd, 2833 groupControlStatus, 2834 groupCount, 2835 groupCurrent, 2836 groupCurrentCapacity, 2837 groupCurrentCrestFactor, 2838 groupCurrentPercentLoad, 2839 groupCurrentThLowerCritical, 2840 groupCurrentThLowerWarning, 2841 groupCurrentThStatus, 2842 groupCurrentThUpperCritical, 2843 groupCurrentThUpperWarning, 2844 groupID, 2845 groupIndex, 2846 groupName, 2847 groupBreakerStatus, 2848 groupPowerFactor, 2849 groupType, 2850 groupVA, 2851 groupVAR, 2852 groupVoltage, 2853 groupVoltageMeasType, 2854 groupVoltageThLowerCritical, 2855 groupVoltageThLowerWarning, 2856 groupVoltageThStatus, 2857 groupVoltageThUpperCritical, 2858 groupVoltageThUpperWarning, 2859 groupWatts, 2860 groupWh, 2861 groupWhTimer, 2862 humidityCount, 2863 humidityIndex, 2864 humidityName, 2865 humidityProbeStatus, 2866 humidityThLowerCritical, 2867 humidityThLowerWarning, 2868 humidityThStatus, 2869 humidityThUpperCritical, 2870 humidityThUpperWarning, 2871 humidityValue, 2872 inputCount, 2873 inputCurrent, 2874 inputCurrentCapacity, 2875 inputCurrentCount, 2876 inputCurrentCrestFactor, 2877 inputCurrentIndex, 2878 inputCurrentMeasType, 2879 inputCurrentPercentLoad, 2880 inputCurrentThLowerCritical, 2881 inputCurrentThLowerWarning, 2882 inputCurrentThStatus, 2883 inputCurrentThUpperCritical, 2884 inputCurrentThUpperWarning, 2885 inputFrequency, 2886 inputFrequencyStatus, 2887 inputIndex, 2888 inputPlugType, 2889 inputPowerCount, 2890 inputPowerFactor, 2891 inputPowerMeasType, 2892 inputType, 2893 inputVA, 2894 inputVAR, 2895 inputVoltage, 2896 inputVoltageCount, 2897 inputVoltageIndex, 2898 inputVoltageMeasType, 2899 inputVoltageThLowerCritical, 2900 inputVoltageThLowerWarning, 2901 inputVoltageThStatus, 2902 inputVoltageThUpperCritical, 2903 inputVoltageThUpperWarning, 2904 inputWatts, 2905 inputWh, 2906 inputWhTimer, 2907 inputTotalVA, 2908 inputTotalWatts, 2909 inputTotalWh, 2910 inputTotalWhTimer, 2911 inputTotalPowerFactor, 2912 inputTotalVAR, 2913 internalStatus, 2914 lcdControl, 2915 outletControlSwitchable, 2916 outletControlShutoffDelay, 2917 outletControlOffCmd, 2918 outletControlOnCmd, 2919 outletControlPowerOnState, 2920 outletControlRebootCmd, 2921 outletControlRebootOffTime, 2922 outletControlSequenceDelay, 2923 outletControlStatus, 2924 outletCount, 2925 outletCurrent, 2926 outletCurrentCapacity, 2927 outletCurrentCrestFactor, 2928 outletCurrentPercentLoad, 2929 outletCurrentThLowerCritical, 2930 outletCurrentThLowerWarning, 2931 outletCurrentThStatus, 2932 outletCurrentThUpperCritical, 2933 outletCurrentThUpperWarning, 2934 outletID, 2935 outletIndex, 2936 outletName, 2937 outletParentCount, 2938 outletParentOID, 2939 outletParentType, 2940 outletPowerFactor, 2941 outletType, 2942 outletVA, 2943 outletVAR, 2944 outletVoltage, 2945 outletVoltageThLowerCritical, 2946 outletVoltageThLowerWarning, 2947 outletVoltageThStatus, 2948 outletVoltageThUpperCritical, 2949 outletVoltageThUpperWarning, 2950 outletWatts, 2951 outletWh, 2952 outletWhTimer, 2953 partNumber, 2954 productName, 2955 serialNumber, 2956 strappingIndex, 2957 strappingStatus, 2958 temperatureCount, 2959 temperatureIndex, 2960 temperatureName, 2961 temperatureProbeStatus, 2962 temperatureScale, 2963 unitType, 2964 temperatureThLowerCritical, 2965 temperatureThLowerWarning, 2966 temperatureThStatus, 2967 temperatureThUpperCritical, 2968 temperatureThUpperWarning, 2969 temperatureValue, 2970 unitControlOffCmd, 2971 unitControlOnCmd, 2972 unitName, 2973 unitsPresent, 2974 userName } 2975 STATUS current 2976 DESCRIPTION 2977 "Most objects in this MIB are optional." 2978 ::= { objectGroups 2 } 2979 2980epduNotifyGroup NOTIFICATION-GROUP 2981 NOTIFICATIONS { notifyBootUp, 2982 notifyCommunicationStatus, 2983 notifyContactState, 2984 notifyFailedLogin, 2985 notifyGroupCurrentThStatus, 2986 notifyGroupVoltageThStatus, 2987 notifyGroupBreakerStatus, 2988 notifyHumidityThStatus, 2989 notifyInputCurrentThStatus, 2990 notifyInputFrequencyStatus, 2991 notifyInputVoltageThStatus, 2992 notifyInternalStatus, 2993 notifyOutletControlStatus, 2994 notifyOutletCurrentThStatus, 2995 notifyOutletVoltageThStatus, 2996 notifyProbeStatus, 2997 notifyStrappingStatus, 2998 notifyTemperatureThStatus, 2999 notifyTest, 3000 notifyUserLogin, 3001 notifyUserLogout } 3002 STATUS current 3003 DESCRIPTION 3004 "These notifications will be supported depending on the features of the ePDU. 3005 Check the web interface for options to turn these notifications on/off. If 3006 an option is not listed, then the ePDU likely does not support that 3007 notification." 3008 ::= { objectGroups 3 } 3009END 3010 3011 3012-- This MIB was created using NuDesign Team's Visual MIBuilder (Ver 4.7). 3013 3014