1# 2# X86_64_LINT -- config file for checking all the sources, tries to pull in 3# as much of the source tree as it can. 4# 5# $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $ 6# 7# See the kernconf(5) manual page for more information on the format of 8# this file. 9# 10# NB: You probably don't want to try running a kernel built from this 11# file. Instead, you should start from X86_64_GENERIC, and add options 12# from this file as required. 13# 14 15# These directives are mandatory. The machine directive specifies the 16# platform and the machine_arch directive specifies the cpu architecture. 17# 18platform pc64 19machine x86_64 20machine_arch x86_64 21 22# 23# This is the ``identification'' of the kernel. Usually this should 24# be the same as the name of your kernel. 25# 26ident X86_64_LINT 27 28# 29# The `maxusers' parameter controls the static sizing of a number of 30# internal system tables by a formula defined in subr_param.c. Setting 31# maxusers to 0 will cause the system to auto-size based on physical 32# memory. 33# 34maxusers 10 35 36# 37# The `makeoptions' parameter allows variables to be passed to the 38# generated Makefile in the build area. 39# 40# CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS} 41# after most other flags. Here we use it to inhibit use of non-optimal 42# gcc builtin functions (e.g., memcmp). 43# 44# DEBUG happens to be magic. 45# The following is equivalent to 'config -g KERNELNAME' and creates 46# 'kernel.debug' compiled with -g debugging as well as a normal 47# 'kernel'. Use 'make install.debug' to install the debug kernel 48# but that isn't normally necessary as the debug symbols are not loaded 49# by the kernel and are not useful there anyway. 50# 51# KERNEL can be overridden so that you can change the default name of your 52# kernel. 53# 54# MODULES_OVERRIDE can be used to limit modules built to a specific list. 55# 56# INSTALLSTRIPPED can be set to cause installkernel to install stripped 57# kernels and modules rather than a kernel and modules with debug symbols. 58# 59# INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be 60# installed, but to strip the installed modules. 61# 62makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc. 63#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols 64#makeoptions KERNEL=foo #Build kernel "foo" and install "/foo" 65# Only build Linux API modules and plus those parts of the sound system I need. 66#makeoptions MODULES_OVERRIDE="linux sound/snd sound/pcm" 67#makeoptions INSTALLSTRIPPED=1 68#makeoptions INSTALLSTRIPPEDMODULES=1 69 70# 71# Certain applications can grow to be larger than the 128M limit 72# that DragonFly initially imposes. Below are some options to 73# allow that limit to grow to 256MB, and can be increased further 74# with changing the parameters. MAXDSIZ is the maximum that the 75# limit can be set to, and the DFLDSIZ is the default value for 76# the limit. MAXSSIZ is the maximum that the stack limit can be 77# set to. You might want to set the default lower than the max, 78# and explicitly set the maximum with a shell command for processes 79# that regularly exceed the limit like INND. 80# 81options MAXDSIZ="(256*1024*1024)" 82options MAXSSIZ="(256*1024*1024)" 83options DFLDSIZ="(256*1024*1024)" 84 85# 86# BLKDEV_IOSIZE sets the default block size used in user block 87# device I/O. Note that this value will be overridden by the label 88# when specifying a block device from a label with a non-0 89# partition blocksize. The default is PAGE_SIZE. 90# 91options BLKDEV_IOSIZE=8192 92 93# This allows you to actually store this configuration file into 94# the kernel binary itself, where it may be later read by saying: 95# strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL 96# 97options INCLUDE_CONFIG_FILE # Include this file in kernel 98 99# 100# The root device and filesystem type can be compiled in; 101# this provides a fallback option if the root device cannot 102# be correctly guessed by the bootstrap code, or an override if 103# the RB_DFLTROOT flag (-r) is specified when booting the kernel. 104# 105options ROOTDEVNAME=\"ufs:da0s2e\" 106 107##################################################################### 108# CPU OPTIONS 109 110cpu HAMMER_CPU 111 112# 113# Options for CPU features. 114# 115# CPU_DISABLE_AVX disables AVX instruction set. 116# 117options CPU_DISABLE_AVX 118 119##################################################################### 120# COMPATIBILITY OPTIONS 121 122# 123# Implement system calls compatible with 4.3BSD and older versions of 124# FreeBSD. You probably do NOT want to remove this as much current code 125# still relies on the 4.3 emulation. 126# 127options COMPAT_43 128 129# Enable NDIS binary driver support 130options NDISAPI 131device ndis 132 133# 134# These three options provide support for System V Interface 135# Definition-style interprocess communication, in the form of shared 136# memory, semaphores, and message queues, respectively. 137# 138# System V shared memory and tunable parameters 139options SHMMIN=2 # min shared memory segment size (bytes) 140options SHMMNI=33 # max number of shared memory identifiers 141options SHMSEG=9 # max shared memory segments per process 142 143# System V semaphores and tunable parameters 144options SEMMAP=31 # amount of entries in semaphore map 145options SEMMNI=11 # number of semaphore identifiers in the system 146options SEMMNS=61 # number of semaphores in the system 147options SEMMNU=31 # number of undo structures in the system 148options SEMMSL=61 # max number of semaphores per id 149options SEMOPM=101 # max number of operations per semop call 150options SEMUME=11 # max number of undo entries per process 151 152# System V message queues and tunable parameters 153options MSGMNB=2049 # max characters per message queue 154options MSGMNI=41 # max number of message queue identifiers 155options MSGSEG=2049 # max number of message segments in the system 156options MSGSSZ=16 # size of a message segment MUST be power of 2 157options MSGTQL=41 # max amount of messages in the system 158 159##################################################################### 160# DEBUGGING OPTIONS 161 162# 163# Enable the kernel debugger. 164# 165options DDB 166 167# 168# Print a stack trace on kernel panic. 169# 170options DDB_TRACE 171 172# 173# Don't drop into DDB for a panic. Intended for unattended operation 174# where you may want to drop to DDB from the console, but still want 175# the machine to recover from a panic 176# 177options DDB_UNATTENDED 178 179# 180# If using GDB remote mode to debug the kernel, there's a non-standard 181# extension to the remote protocol that can be used to use the serial 182# port as both the debugging port and the system console. It's non- 183# standard and you're on your own if you enable it. See also the 184# "remotechat" variables in the DragonFly specific version of gdb. 185# 186options GDB_REMOTE_CHAT 187 188# 189# KTRACE enables the system-call tracing facility ktrace(2). 190# 191options KTRACE #kernel tracing 192 193# 194# The INVARIANTS option is used in a number of source files to enable 195# extra sanity checking of internal structures. This support is not 196# enabled by default because of the extra time it would take to check 197# for these conditions, which can only occur as a result of 198# programming errors. 199# 200options INVARIANTS 201 202# 203# The DIAGNOSTIC option is used to enable extra debugging information 204# from some parts of the kernel. As this makes everything more noisy, 205# it is disabled by default. 206# 207options DIAGNOSTIC 208 209# 210# PERFMON causes the driver for Pentium/Pentium Pro performance counters 211# to be compiled. See perfmon(4) for more information. 212# 213options PERFMON 214 215 216# 217# This option let some drivers co-exist that can't co-exist in a running 218# system. This is used to be able to compile all kernel code in one go for 219# quality assurance purposes (like this file, which the option takes it name 220# from.) 221# 222options COMPILING_LINT 223 224 225# XXX - this doesn't belong here. 226# Allow ordinary users to take the console - this is useful for X. 227options UCONSOLE 228 229##################################################################### 230# NETWORKING OPTIONS 231 232# 233# Protocol families: 234# Only the INET (Internet) family is officially supported in DragonFly. 235# Source code for the NS (Xerox Network Service) is provided for amusement 236# value. 237# 238options INET #Internet communications protocols 239options INET6 #IPv6 communications protocols 240options IPSEC #IP security 241options IPSEC_ESP #IP security (crypto; define w/ IPSEC) 242options IPSEC_DEBUG #debug for IP security 243# 244# Set IPSEC_FILTERGIF to force packets coming through a gif tunnel 245# to be processed by any configured packet filtering (ipfw). 246# The default is that packets coming from a tunnel are _not_ processed; 247# they are assumed trusted. 248# 249# Note that enabling this can be problematic as there are no mechanisms 250# in place for distinguishing packets coming out of a tunnel (e.g. no 251# encX devices as found on openbsd). 252# 253#options IPSEC_FILTERGIF #filter ipsec packets from a tunnel 254 255# 256# Experimental IPsec implementation that uses the kernel crypto 257# framework. This cannot be configured together with IPSEC and 258# (currently) supports only IPv4. To use this you must also 259# configure the crypto device (see below). Note that with this 260# you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP). 261# IPSEC_DEBUG is used, as above, to configure debugging support 262# within the IPsec protocols. 263# 264#options FAST_IPSEC #new IPsec 265 266options MPLS #Multi-Protocol Label Switching 267 268# 269# SMB/CIFS requester 270# NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV 271# options. 272# NETSMBCRYPTO enables support for encrypted passwords. 273options NETSMB #SMB/CIFS requester 274options NETSMBCRYPTO #encrypted password support for SMB 275 276# mchain library. It can be either loaded as KLD or compiled into kernel 277options LIBMCHAIN #mbuf management library 278 279# netgraph(4). Enable the base netgraph code with the NETGRAPH option. 280# Individual node types can be enabled with the corresponding option 281# listed below; however, this is not strictly necessary as netgraph 282# will automatically load the corresponding KLD module if the node type 283# is not already compiled into the kernel. Each type below has a 284# corresponding man page, e.g., ng_async(4). 285options NETGRAPH #netgraph(4) system 286options NETGRAPH_ASYNC 287options NETGRAPH_BPF 288options NETGRAPH_BRIDGE 289options NETGRAPH_CISCO 290options NETGRAPH_ECHO 291options NETGRAPH_EIFACE 292options NETGRAPH_ETHER 293options NETGRAPH_FEC 294options NETGRAPH_FRAME_RELAY 295options NETGRAPH_HOLE 296options NETGRAPH_IFACE 297options NETGRAPH_KSOCKET 298options NETGRAPH_L2TP 299options NETGRAPH_LMI 300# MPPC compression requires proprietary files (not included) 301#options NETGRAPH_MPPC_COMPRESSION 302options NETGRAPH_MPPC_ENCRYPTION 303options NETGRAPH_ONE2MANY 304options NETGRAPH_PPP 305options NETGRAPH_PPPOE 306options NETGRAPH_PPTPGRE 307options NETGRAPH_RFC1490 308options NETGRAPH_SOCKET 309options NETGRAPH_TEE 310options NETGRAPH_TTY 311options NETGRAPH_UI 312options NETGRAPH_VJC 313 314device mn # Munich32x/Falc54 Nx64kbit/sec cards. 315 316# 317# Network interfaces: 318# The `loop' pseudo-device is MANDATORY when networking is enabled. 319# The `ether' pseudo-device provides generic code to handle 320# Ethernets; it is MANDATORY when a Ethernet device driver is 321# configured. 322# The `sppp' pseudo-device serves a similar role for certain types 323# of synchronous PPP links (like `ar'). 324# The `sl' pseudo-device implements the Serial Line IP (SLIP) service. 325# The `ppp' pseudo-device implements the Point-to-Point Protocol. 326# The `bpf' pseudo-device enables the Berkeley Packet Filter. Be 327# aware of the legal and administrative consequences of enabling this 328# option. The number of devices determines the maximum number of 329# simultaneous BPF clients programs runnable. 330# The `disc' pseudo-device implements a minimal network interface, 331# which throws away all packets sent and never receives any. It is 332# included for testing purposes. This shows up as the 'ds' interface. 333# The `tun' pseudo-device implements (user-)ppp and nos-tun 334# The `gif' pseudo-device implements IPv6 over IP4 tunneling, 335# IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and 336# IPv6 over IPv6 tunneling. 337# The `gre' device implements two types of IP4 over IP4 tunneling: 338# GRE and MOBILE, as specified in the RFC1701 and RFC2004. 339# The `faith' pseudo-device captures packets sent to it and diverts them 340# to the IPv4/IPv6 translation daemon. 341# The `stf' device implements 6to4 encapsulation. 342# The `ef' pseudo-device provides support for multiple ethernet frame types 343# specified via ETHER_* options. See ef(4) for details. 344# 345# The PPP_BSDCOMP option enables support for compress(1) style entire 346# packet compression, the PPP_DEFLATE is for zlib/gzip style compression. 347# PPP_FILTER enables code for filtering the ppp data stream and selecting 348# events for resetting the demand dial activity timer - requires bpf. 349# See pppd(8) for more details. 350# 351pseudo-device ether #Generic Ethernet 352pseudo-device vlan 1 #VLAN support 353pseudo-device bridge #Bridging support 354pseudo-device sppp #Generic Synchronous PPP 355pseudo-device loop #Network loopback device 356pseudo-device bpf #Berkeley packet filter 357pseudo-device disc #Discard device (ds0, ds1, etc) 358pseudo-device tap #Ethernet tunnel network interface 359pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8)) 360pseudo-device sl 2 #Serial Line IP 361pseudo-device gre #IP over IP tunneling 362pseudo-device ppp 2 #Point-to-point protocol 363options PPP_BSDCOMP #PPP BSD-compress support 364options PPP_DEFLATE #PPP zlib/deflate/gzip support 365options PPP_FILTER #enable bpf filtering (needs bpf) 366 367# for IPv6 368pseudo-device gif #IPv6 and IPv4 tunneling 369pseudo-device faith 1 #for IPv6 and IPv4 translation 370pseudo-device stf #6to4 IPv6 over IPv4 encapsulation 371 372# 373# Internet family options: 374# 375# MROUTING enables the kernel multicast packet forwarder, which works 376# with mrouted(8). 377# 378# PIM enables Protocol Independent Multicast in the kernel. 379# Requires MROUTING enabled. 380# 381# IPFIREWALL enables support for IP firewall construction, in 382# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends 383# logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT 384# limits the number of times a matching entry can be logged. 385# 386# WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any" 387# and if you do not add other rules during startup to allow access, 388# YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open 389# in /etc/rc.conf when first enabling this feature, then refining the 390# firewall rules in /etc/rc.firewall after you've tested that the new kernel 391# feature works properly. 392# 393# IPFIREWALL3 is based on a newer version of FreeBSD's ipfw2, along with 394# some enhancements. See ipfw3(4). 395# 396# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to 397# allow everything. Use with care, if a cracker can crash your 398# firewall machine, they can get to your protected machines. However, 399# if you are using it as an as-needed filter for specific problems as 400# they arise, then this may be for you. Changing the default to 'allow' 401# means that you won't get stuck if the kernel and /sbin/ipfw binary get 402# out of sync. 403# 404# IPDIVERT enables the divert IP sockets, used by ``ipfw divert'' 405# 406# IPSTEALTH enables code to support stealth forwarding (i.e., forwarding 407# packets without touching the ttl). This can be useful to hide firewalls 408# from traceroute and similar tools. 409# 410# TCPDEBUG is undocumented. 411# 412# ICMPPRINTFS enables ICMP to do extra debug prints. 413# 414options MROUTING # Multicast routing 415options PIM # Protocol Independent Multicast 416options IPFIREWALL #firewall 417options IPFIREWALL_DEBUG #debug prints 418options IPFIREWALL_VERBOSE #enable logging to syslogd(8) 419options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity 420options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default 421options IPV6FIREWALL #firewall for IPv6 422options IPV6FIREWALL_VERBOSE 423options IPV6FIREWALL_VERBOSE_LIMIT=100 424options IPV6FIREWALL_DEFAULT_TO_ACCEPT 425options IPDIVERT #divert sockets 426options IPSTEALTH #support for stealth forwarding 427options TCPDEBUG 428options ICMPPRINTFS 429 430options IPFIREWALL3 431 432device pf 433device pflog 434 435#CARP 436pseudo-device carp 437options CARP 438 439# The MBUF_STRESS_TEST option enables options which create 440# various random failures / extreme cases related to mbuf 441# functions. See the mbuf(9) manpage for a list of available 442# test cases. 443options MBUF_STRESS_TEST 444 445# Statically link in accept filters 446options ACCEPT_FILTER_DATA 447options ACCEPT_FILTER_HTTP 448 449# TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are 450# carried in TCP option 19. This option is commonly used to protect 451# TCP sessions (e.g. BGP) where IPSEC is not available nor desirable. 452# This is enabled on a per-socket basis using the TCP_SIGNATURE_ENABLE 453# socket option. 454# This requires the use of 'device crypto', 'options IPSEC' 455# or 'device cryptodev'. 456options TCP_SIGNATURE #include support for RFC 2385 457 458# 459# TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This 460# prevents nmap et al. from identifying the TCP/IP stack, but breaks support 461# for RFC1644 extensions and is not recommended for web servers. 462# 463options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN 464 465# ICMP_BANDLIM enables icmp error response bandwidth limiting. You 466# typically want this option as it will help protect the machine from 467# D.O.S. packet attacks. 468# 469options ICMP_BANDLIM 470 471# DUMMYNET enables the "dummynet" bandwidth limiter. You need 472# IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info. 473# 474options DUMMYNET 475options DUMMYNET_DEBUG 476 477# IFPOLL_ENABLE adds support for mixed interrupt-polling handling 478# of network device drivers, which has significant benefits in terms 479# of robustness to overloads and responsivity, as well as permitting 480# accurate scheduling of the CPU time between kernel network processing 481# and other activities. The drawback is a moderate (up to 1/pollhz seconds) 482# potential increase in response times. See polling(4) for further details. 483# 484# IFPOLL_ENABLE adds hardware queues' based polling 485options IFPOLL_ENABLE 486 487##################################################################### 488# FILESYSTEM OPTIONS 489 490# 491# Only the root, /usr, and /tmp filesystems need be statically 492# compiled; everything else will be automatically loaded at mount 493# time. (Exception: the UFS family --- FFS, and MFS --- 494# cannot currently be demand-loaded.) Some people still prefer 495# to statically compile other filesystems as well. 496# 497# NB: The PORTAL and UNION filesystems are known to be 498# buggy, and WILL panic your system if you attempt to do anything with 499# them. They are included here as an incentive for some enterprising 500# soul to sit down and fix them. 501# 502 503# One of these is mandatory: 504options FFS #Fast filesystem 505options MFS #Memory filesystem 506options NFS #Network filesystem 507 508# The rest are optional: 509#options NFS_NOSERVER #Disable the NFS-server code. 510options CD9660 #ISO 9660 filesystem 511options HAMMER #HAMMER filesystem 512options HPFS #OS/2 File system 513options MSDOSFS #MS DOS filesystem 514options NTFS #NT filesystem 515options NULLFS #NULL filesystem 516options PORTAL #Portal filesystem 517options PROCFS #Process filesystem 518options PUFFS #Userspace file systems (e.g. ntfs-3g & sshfs) 519options SMBFS #SMB/CIFS filesystem 520options TMPFS #Temporary filesystem 521options UDF #UDF filesystem 522 523# YYY-DR Till we rework the VOP methods for this filesystem 524#options UNION #Union filesystem 525# The xFS_ROOT options REQUIRE the associated ``options xFS'' 526options FFS_ROOT #FFS usable as root device 527options NFS_ROOT #NFS usable as root device 528 529# Soft updates is technique for improving UFS filesystem speed and 530# making abrupt shutdown less risky. 531options SOFTUPDATES 532 533# Directory hashing improves the speed of operations on very large 534# directories at the expense of some memory. 535options UFS_DIRHASH 536 537# Make space in the kernel for a root filesystem on a md device. 538# Define to the number of kilobytes to reserve for the filesystem. 539options MD_ROOT_SIZE=10 540 541# Make the md device a potential root device, either with preloaded 542# images of type mfs_root or md_root. 543options MD_ROOT 544 545# Specify double the default maximum size for malloc(9)-backed md devices. 546options MD_NSECT=40000 547 548# Allow this many swap-devices. 549# 550# In order to manage swap, the system must reserve bitmap space that 551# scales with the largest mounted swap device multiplied by NSWAPDEV, 552# regardless of whether other swap devices exist or not. So it 553# is not a good idea to make this value too large. 554options NSWAPDEV=5 555 556# Disk quotas are supported when this option is enabled. 557options QUOTA #enable disk quotas 558 559# If you are running a machine just as a fileserver for PC and MAC 560# users, e.g. using SAMBA, you may consider setting this option 561# and keeping all those users' directories on a filesystem that is 562# mounted with the suiddir option. This gives new files the same 563# ownership as the directory (similar to group). It's a security hole 564# if you let these users run programs, so confine it to file-servers 565# (but it'll save you lots of headaches in those cases). Root owned 566# directories are exempt and X bits are cleared. The suid bit must be 567# set on the directory as well; see chmod(1) PC owners can't see/set 568# ownerships so they keep getting their toes trodden on. This saves 569# you all the support calls as the filesystem it's used on will act as 570# they expect: "It's my dir so it must be my file". 571# 572options SUIDDIR 573 574# NFS options: 575options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec 576options NFS_MAXATTRTIMO=60 577options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec 578options NFS_MAXDIRATTRTIMO=60 579options NFS_GATHERDELAY=10 # Default write gather delay (msec) 580options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this 581options NFS_WDELAYHASHSIZ=16 # and with this 582options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this 583options NFS_DEBUG # Enable NFS Debugging 584 585# NTFS options: 586options NTFS_DEBUG 587 588# MSDOSFS options: 589options MSDOSFS_DEBUG # Enable MSDOSFS Debugging 590 591# 592# Add support for the EXT2FS filesystem of Linux fame. Be a bit 593# careful with this - the ext2fs code has a tendency to lag behind 594# changes and not be exercised very much, so mounting read/write could 595# be dangerous (and even mounting read only could result in panics.) 596# 597options EXT2FS 598 599# Optional character code conversion support with LIBICONV. 600# Each option requires their base file system and LIBICONV. 601options CD9660_ICONV 602options MSDOSFS_ICONV 603options NTFS_ICONV 604 605##################################################################### 606# POSIX P1003.1B 607 608# Real time extensions added in the 1993 Posix 609# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING 610 611options _KPOSIX_PRIORITY_SCHEDULING 612 613##################################################################### 614# CLOCK OPTIONS 615 616# The granularity of operation is controlled by the kernel option HZ whose 617# default value (100) means a granularity of 10ms (1s/HZ). 618# Consider, however, that reducing the granularity too much might 619# cause excessive overhead in clock interrupt processing, 620# potentially causing ticks to be missed and thus actually reducing 621# the accuracy of operation. 622 623options HZ=100 624 625# The following options are used for debugging clock behavior only, and 626# should not be used for production systems. 627# 628# CLK_CALIBRATION_LOOP will run the clock calibration loop at startup 629# until the user presses a key. 630 631#options CLK_CALIBRATION_LOOP 632 633# The following two options measure the frequency of the corresponding 634# clock relative to the RTC (onboard mc146818a). 635 636#options CLK_USE_I8254_CALIBRATION 637#options CLK_USE_TSC_CALIBRATION 638 639##################################################################### 640# SCSI DEVICES 641 642# SCSI DEVICE CONFIGURATION 643 644# The SCSI subsystem consists of the `base' SCSI code, a number of 645# high-level SCSI device `type' drivers, and the low-level host-adapter 646# device drivers. The host adapters are listed in the ISA and PCI 647# device configuration sections below. 648# 649# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so 650# that a given bus, target, and LUN always come on line as the same 651# device unit. In earlier versions the unit numbers were assigned 652# in the order that the devices were probed on the SCSI bus. This 653# means that if you removed a disk drive, you may have had to rewrite 654# your /etc/fstab file, and also that you had to be careful when adding 655# a new disk as it may have been probed earlier and moved your device 656# configuration around. 657 658# This old behavior is maintained as the default behavior. The unit 659# assignment begins with the first non-wired down unit for a device 660# type. For example, if you wire a disk as "da3" then the first 661# non-wired disk will be assigned da4. 662 663# The syntax for wiring down devices is: 664 665# device scbus0 at ahc0 # Single bus device 666# device scbus1 at ahc1 bus 0 # Single bus device 667# device scbus3 at ahc2 bus 0 # Twin bus device 668# device scbus2 at ahc2 bus 1 # Twin bus device 669# device da0 at scbus0 target 0 unit 0 670# device da1 at scbus3 target 1 671# device da2 at scbus2 target 3 672# device sa1 at scbus1 target 6 673# device cd 674 675# "units" (SCSI logical unit number) that are not specified are 676# treated as if specified as LUN 0. 677 678# All SCSI devices allocate as many units as are required. 679 680# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI 681# configuration and doesn't have to be explicitly configured. 682 683device scbus #base SCSI code 684device ch #SCSI media changers 685device da #SCSI direct access devices (aka disks) 686device sa #SCSI tapes 687device cd #SCSI CD-ROMs 688device pass #CAM passthrough driver 689device sg #Passthrough device (linux scsi generic) 690device pt #SCSI processor type 691device ses #SCSI SES/SAF-TE driver 692device targ #SCSI Target Mode Code 693device targbh #SCSI Target Mode Blackhole Device 694 695# Options for device mapper 696device dm 697device dm_target_crypt 698device dm_target_linear 699device dm_target_striped 700 701# Options for iSCSI 702device iscsi_initiator 703options ISCSI_INITIATOR_DEBUG=8 704 705# CAM OPTIONS: 706# debugging options: 707# -- NOTE -- If you specify one of the bus/target/lun options, you must 708# specify them all! 709# CAMDEBUG: When defined enables debugging macros 710# CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses. 711# CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets. 712# CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns. 713# CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE, 714# CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB 715# 716# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds 717# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions 718# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions 719# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter) 720# queue after a bus reset, and the number of milliseconds to 721# freeze the device queue after a bus device reset. This 722# can be changed at boot and runtime with the 723# kern.cam.scsi_delay tunable/sysctl. 724options CAMDEBUG 725options CAM_DEBUG_BUS=-1 726options CAM_DEBUG_TARGET=-1 727options CAM_DEBUG_LUN=-1 728options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB" 729options CAM_MAX_HIGHPOWER=4 730options SCSI_NO_SENSE_STRINGS 731options SCSI_NO_OP_STRINGS 732options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device 733 734# Options for the CAM CDROM driver: 735# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN 736# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only 737# enforced if there is I/O waiting for another LUN 738# The compiled in defaults for these variables are 2 and 10 seconds, 739# respectively. 740# 741# These can also be changed on the fly with the following sysctl variables: 742# kern.cam.cd.changer.min_busy_seconds 743# kern.cam.cd.changer.max_busy_seconds 744# 745options CHANGER_MIN_BUSY_SECONDS=2 746options CHANGER_MAX_BUSY_SECONDS=10 747 748# Options for the CAM sequential access driver: 749# SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes 750# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes 751# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes 752# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes 753# SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT. 754options SA_IO_TIMEOUT="(4)" 755options SA_SPACE_TIMEOUT="(60)" 756options SA_REWIND_TIMEOUT="(2*60)" 757options SA_ERASE_TIMEOUT="(4*60)" 758options SA_1FM_AT_EOD 759 760# Optional timeout for the CAM processor target (pt) device 761# This is specified in seconds. The default is 60 seconds. 762options SCSI_PT_DEFAULT_TIMEOUT="60" 763 764# Optional enable of doing SES passthrough on other devices (e.g., disks) 765# 766# Normally disabled because a lot of newer SCSI disks report themselves 767# as having SES capabilities, but this can then clot up attempts to build 768# build a topology with the SES device that's on the box these drives 769# are in.... 770options SES_ENABLE_PASSTHROUGH 771 772##################################################################### 773# MISCELLANEOUS DEVICES AND OPTIONS 774 775# The `pty' device usually turns out to be ``effectively mandatory'', 776# as it is required for `telnetd', `rlogind', `screen', `emacs', and 777# `xterm', among others. 778 779pseudo-device pty # Pseudo ttys 780pseudo-device gzip # Exec gzipped a.out's 781pseudo-device md # Memory/malloc disk 782pseudo-device vn # File image "disks" 783pseudo-device putter # for puffs and pud 784pseudo-device snp # Snoop device - to look at pty/vty/etc.. 785pseudo-device ccd 4 # Concatenated disk driver 786 787# Configuring Vinum into the kernel is not necessary, since the kld 788# module gets started automatically when vinum(8) starts. This 789# device is also untested. Use at your own risk. 790# 791# The option VINUMDEBUG must match the value set in CFLAGS 792# in src/sbin/vinum/Makefile. Failure to do so will result in 793# the following message from vinum(8): 794# 795# Can't get vinum config: Invalid argument 796# 797# see vinum(4) for more reasons not to use these options. 798pseudo-device vinum #Vinum concat/mirror/raid driver 799options VINUMDEBUG #enable Vinum debugging hooks 800 801# Kernel side iconv library 802options LIBICONV 803 804# Size of the kernel message buffer. Should be N * pagesize. 805options MSGBUF_SIZE=40960 806 807##################################################################### 808# HARDWARE DEVICE CONFIGURATION 809 810# ISA devices: 811 812# 813# Mandatory ISA devices: isa 814# 815device isa 816 817# 818# Options for `isa': 819# 820# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A 821# interrupt controller. This saves about 0.7-1.25 usec for each interrupt. 822# This option breaks suspend/resume on some portables. 823# 824# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A 825# interrupt controller. This saves about 0.7-1.25 usec for each interrupt. 826# Automatic EOI is documented not to work for the slave with the 827# original i8259A, but it works for some clones and some integrated 828# versions. 829# 830# MAXMEM specifies the amount of RAM on the machine; if this is not 831# specified, DragonFly will first read the amount of memory from the CMOS 832# RAM, so the amount of memory will initially be limited to 64MB or 16MB 833# depending on the BIOS. If the BIOS reports 64MB, a memory probe will 834# then attempt to detect the installed amount of RAM. If this probe 835# fails to detect >64MB RAM you will have to use the MAXMEM option. 836# The amount is in kilobytes, so for a machine with 128MB of RAM, it would 837# be 131072 (128 * 1024). 838# 839# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to 840# reset the CPU for reboot. This is needed on some systems with broken 841# keyboard controllers. 842 843options AUTO_EOI_1 844#options AUTO_EOI_2 845options MAXMEM="(128*1024)" 846#options BROKEN_KEYBOARD_RESET 847 848# Enable support for the kernel PLL to use an external PPS signal, 849# under supervision of [x]ntpd(8) 850# More info in ntpd documentation: http://www.eecis.udel.edu/~ntp 851 852options PPS_SYNC 853 854# The keyboard controller; it controls the keyboard and the PS/2 mouse. 855device atkbdc0 at isa? port IO_KBD 856 857# The AT keyboard 858device atkbd0 at atkbdc? irq 1 859 860# Options for atkbd: 861options ATKBD_DFLT_KEYMAP # specify the built-in keymap 862makeoptions ATKBD_DFLT_KEYMAP="jp.106" 863 864# These options are valid for other keyboard drivers as well. 865options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap 866options KBD_INSTALL_CDEV # install a CDEV entry in /dev 867 868# `flags' for atkbd: 869# 0x01 Force detection of keyboard, else we always assume a keyboard 870# 0x02 Don't reset keyboard, useful for some newer ThinkPads 871# 0x03 Force detection and avoid reset, might help with certain 872# dockingstations 873# 0x04 Old-style (XT) keyboard support, useful for older ThinkPads 874 875# PS/2 mouse 876device psm0 at atkbdc? irq 12 877 878# Options for psm: 879options PSM_HOOKRESUME #hook the system resume event, useful 880 #for some laptops 881options PSM_RESETAFTERSUSPEND #reset the device at the resume event 882 883device kbdmux # keyboard multiplexer 884 885# The video card driver. 886device vga0 at isa? 887 888# Options for vga: 889options VGA_DEBUG=2 # enable VGA debug output 890 891# If you experience problems switching back to 80x25 (or a derived mode), 892# the following option might help. 893#options VGA_KEEP_POWERON_MODE # use power-on settings for 80x25 894 895# If you can dispense with some vga driver features, you may want to 896# use the following options to save some memory. 897#options VGA_NO_FONT_LOADING # don't save/load font 898#options VGA_NO_MODE_CHANGE # don't change video modes 899 900# The following option probably won't work with the LCD displays. 901options VGA_WIDTH90 # support 90 column modes 902 903# Splash screen at start up! Screen savers require this too. 904pseudo-device splash 905 906# The syscons console driver (sco color console compatible). 907device sc0 at isa? 908options MAXCONS=16 # number of virtual consoles 909options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode 910options SC_DEBUG_LEVEL=5 # enable debug output 911options SC_DFLT_FONT # compile font in 912makeoptions SC_DFLT_FONT=cp850 913options SC_DISABLE_DDBKEY # disable `debug' key 914options SC_DISABLE_REBOOT # disable reboot key sequence 915options SC_HISTORY_SIZE=200 # number of history buffer lines 916options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor 917options SC_PIXEL_MODE # add support for the raster text mode 918 919# The following options will let you change the default colors of syscons. 920options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)" 921options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)" 922options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)" 923options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)" 924 925# If you have a two button mouse, you may want to add the following option 926# to use the right button of the mouse to paste text. 927options SC_TWOBUTTON_MOUSE 928 929# You can selectively disable features in syscons. 930#options SC_NO_CUTPASTE 931#options SC_NO_FONT_LOADING 932#options SC_NO_HISTORY 933#options SC_NO_SYSMOUSE 934 935# 936# SCSI host adapters 937# 938# adv: All Narrow SCSI bus AdvanSys controllers. 939# adw: Second Generation AdvanSys controllers including the ADV940UW. 940# ahc: Adaptec 274x/284x/294x 941# aic: Adaptec 1460 942# bt: Most Buslogic controllers 943# ncv: NCR 53C500 based SCSI host adapters. 944# nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters. 945# stg: TMC 18C30, 18C50 based PC Card SCSI host adapters. 946# 947# Note that the order is important in order for Buslogic cards to be 948# probed correctly. 949# 950 951device bt 952device adv 953device adw 954device aic 955device ncv 956device nsp 957device stg 958 959# 960# Adaptec FSA RAID controllers, including integrated DELL controller, 961# the Dell PERC 2/QC and the HP NetRAID-4M 962# 963device aac 964options AAC_DEBUG 965device aacp # SCSI Passthrough interface (optional, CAM required) 966 967# 968# Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only 969# one entry is needed; the code will find and configure all supported 970# controllers. 971# 972device ida # Compaq Smart RAID 973device mlx # Mylex DAC960 974device amr # AMI MegaRAID 975device amrp # SCSI Passthrough interface (optional, CAM req.) 976options AMR_DEBUG=3 977device mfi # LSI MegaRAID SAS 978device mfip # LSI MegaRAID SAS passthrough, requires CAM 979options MFI_DEBUG 980 981# 982# LSI MegaRAID 6Gb/s and 12Gb/s SAS+SATA RAID controller driver 983# 984device mrsas 985 986# 987# Areca RAID (CAM is required). 988# 989device arcmsr # Areca SATA II RAID 990 991# 992# Highpoint RocketRAID 182x. 993device hptmv 994 995# 996# Highpoint RocketRAID. Supports RR172x, RR222x, RR2240, RR232x, RR2340, 997# RR2210, RR174x, RR2522, RR231x, RR230x. 998device hptrr 999 1000# 1001# Highpoint RocketRAID 27xx. 1002device "hpt27xx" 1003 1004# 1005# Highpoint RocketRaid 3xxx series SATA RAID 1006device hptiop 1007 1008# 1009# 3ware ATA RAID 1010# 1011device twe # 3ware ATA RAID 1012device twa # 3ware 9000 series PATA/SATA RAID 1013options TWA_DEBUG=10 # enable debug messages 1014device tws # 3ware 9750 series SATA/SAS RAID 1015 1016# 1017# IBM ServeRAID 1018# 1019device ips 1020 1021# AHCI driver, this will override NATA for AHCI devices, 1022# both drivers may be included. 1023# 1024device ahci 1025 1026# SiI3124/3132 driver 1027# 1028device sili 1029 1030# The 'NATA' driver supports all ATA and ATAPI devices. 1031# You only need one "device nata" for it to find all 1032# PCI ATA/ATAPI devices on modern machines. 1033# 1034device nata 1035device natadisk # ATA disk drives 1036device natapicd # ATAPI CD/DVD drives 1037device natapifd # ATAPI floppy drives 1038device natapist # ATAPI tape drives 1039device natapicam # ATAPI CAM layer emulation 1040device nataraid # support for ATA software RAID controllers 1041 1042# The following options are valid for the NATA driver: 1043# 1044# ATA_STATIC_ID: controller numbering is static (like the old driver) 1045# else the device numbers are dynamically allocated. 1046options ATA_STATIC_ID 1047 1048# For older non-PCI systems, these are the lines to use: 1049# 1050#device nata0 at isa? port IO_WD1 irq 14 1051#device nata1 at isa? port IO_WD2 irq 15 1052 1053# 1054# Standard floppy disk controllers: `fdc' and `fd' 1055# 1056#device fdc0 at isa? port IO_FD1 irq 6 drq 2 1057# 1058# FDC_DEBUG enables floppy debugging. Since the debug output is huge, you 1059# gotta turn it actually on by setting the variable fd_debug with DDB, 1060# however. 1061#options FDC_DEBUG 1062 1063#device fd0 at fdc0 drive 0 1064#device fd1 at fdc0 drive 1 1065 1066# 1067# sio: serial ports (see sio(4)) 1068 1069device sio0 at isa? port IO_COM1 flags 0x10 irq 4 1070 1071# 1072# `flags' for serial drivers that support consoles (only for sio now): 1073# 0x10 enable console support for this unit. The other console flags 1074# are ignored unless this is set. Enabling console support does 1075# not make the unit the preferred console - boot with -h or set 1076# the 0x20 flag for that. Currently, at most one unit can have 1077# console support; the first one (in config file order) with 1078# this flag set is preferred. Setting this flag for sio0 gives 1079# the old behaviour. 1080# 0x20 force this unit to be the console (unless there is another 1081# higher priority console). This replaces the COMCONSOLE option. 1082# 0x40 reserve this unit for low level console operations. Do not 1083# access the device in any normal way. 1084# 0x80 use this port for serial line gdb support in ddb. 1085# 1086 1087# Options for serial drivers that support consoles (only for sio now): 1088options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to 1089 #DDB, if available. 1090options CONSPEED=115200 # speed for serial console 1091 # (default 9600) 1092 1093# Solaris implements a new BREAK which is initiated by a character 1094# sequence CR ~ ^b which is similar to a familiar pattern used on 1095# Sun servers by the Remote Console. 1096options ALT_BREAK_TO_DEBUGGER 1097 1098# Options for sio: 1099options COM_ESP #code for Hayes ESP 1100options COM_MULTIPORT #code for some cards with shared IRQs 1101 1102# Other flags for sio that aren't documented in the man page. 1103# 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for 1104# ST16650A-compatible UARTs. 1105 1106# PCI Universal Communications driver 1107# Supports various single and multi port PCI serial cards. Maybe later 1108# also the parallel ports on combination serial/parallel cards. New cards 1109# can be added in src/sys/dev/misc/puc/pucdata.c. 1110device puc 1111 1112# 1113# Network interfaces: `ed', `ep', `is', `lnc' 1114# 1115# cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters 1116# ep: 3Com 3C509 1117# ex: Intel EtherExpress Pro/10 and other i82595-based adapters 1118# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960) 1119# sbsh: Granch SBNI16 SHDSL modem PCI adapters 1120# wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both 1121# the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA 1122# bridge with a PCMCIA adapter plugged into it. 1123# an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA, 1124# PCI and ISA varieties. 1125# xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller. 1126# 1127device cs 1128device ep 1129device ex 1130device lnc 1131device sln 1132device sn 1133 1134# Wlan support is mandatory for some wireless LAN devices. 1135options IEEE80211_DEBUG #enable debugging msgs 1136options IEEE80211_AMPDU_AGE #age frames in AMPDU reorder q's 1137options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support 1138options IEEE80211_SUPPORT_TDMA #enable TDMA support 1139device wlan # 802.11 support 1140device wlan_acl # 802.11 MAC-based access control for AP 1141device wlan_ccmp # 802.11 CCMP support 1142device wlan_tkip # 802.11 TKIP support 1143device wlan_wep # 802.11 WEP support 1144device wlan_xauth # 802.11 WPA or 802.1x authentication for AP 1145device wlan_amrr # 802.11 AMRR TX rate control algorithm 1146device an # Aironet Communications 4500/4800 1147device ath # Atheros AR521x 1148options AH_AR5416_INTERRUPT_MITIGATION 1149options AH_ASSERT 1150options AH_DEBUG 1151options AH_INTERRUPT_DEBUGGING 1152options AH_MAXCHAN=96 1153options AH_NEED_DESC_SWAP 1154options AH_PRIVATE_DIAG 1155options AH_REGOPS_FUNC 1156options AH_RXCFG_SDMAMW_4BYTES 1157options AH_SUPPORT_AR5416 1158options AH_SUPPORT_AR9130 1159options AH_SUPPORT_AR9330 1160options AH_SUPPORT_AR9340 1161options AH_USE_INIPDGAIN 1162device ath_hal # Atheros Hardware Access Layer 1163#device ath_rate_amrr # Atheros AMRR TX rate control algorithm 1164#device ath_rate_onoe # Atheros Onoe TX rate control algorithm 1165device ath_rate_sample # Atheros Sample TX rate control algorithm 1166options ATH_DEBUG # turn on debugging output (see hw.ath.debug) 1167options ATH_DIAGAPI # diagnostic interface to the HAL 1168options ATH_ENABLE_DFS 1169options ATH_KTR_INTR_DEBUG 1170device siba_bwn # Sonic Inc. Silicon Backplane needed for bwn 1171options SIBA_DEBUG # turn on debugging output 1172device bwn # Broadcom BCM43xx NICs using v4 firmware 1173options BWN_DEBUG # turn on debugging output 1174options BWN_RXRING_SLOTS=128 # number of RX slots to allocate 1175options BWN_TXRING_SLOTS=128 # number of TX slots to allocate 1176device iwi # Intel PRO/Wireless 2200BG/2915ABG 1177device iwm # Intel Dual Band Wireless AC 3160/7260/7265 1178device iwn # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050 1179options IWN_DEBUG # turn on debugging output 1180device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS 1181device xe # Xircom PCMCIA 1182device ral # Ralink Technology 802.11 wireless NIC 1183device wpi 1184 1185# IEEE 802.11 adapter firmware modules 1186 1187# iwifw: Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware 1188# iwmfw Intel Dual Band Wireless AC 3160/7260/7265 1189# iwnfw: Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050 1190# ralfw: Ralink Technology RT25xx and RT26xx firmware 1191# wpifw: Intel 3945ABG Wireless LAN Controller firmware 1192 1193device iwifw 1194device iwmfw 1195device iwnfw 1196device ralfw 1197device wpifw 1198 1199# Bluetooth Protocols 1200device bluetooth 1201 1202# Sound drivers 1203# 1204 1205# Basic sound card support: 1206device sound 1207# For PCI sound cards: 1208device "snd_als4000" 1209device "snd_atiixp" 1210device "snd_cmi" 1211device "snd_cs4281" 1212device "snd_emu10k1" 1213device "snd_emu10kx" 1214device "snd_envy24" 1215device "snd_envy24ht" 1216device "snd_es137x" 1217device "snd_fm801" 1218device "snd_hda" 1219device "snd_hdspe" 1220device "snd_ich" 1221device "snd_maestro" 1222device "snd_neomagic" 1223device "snd_solo" 1224device "snd_spicds" 1225device "snd_t4dwave" 1226device "snd_via8233" 1227device "snd_via82c686" 1228device "snd_vibes" 1229# USB 1230device "snd_uaudio" 1231 1232# 1233# Following options are intended for debugging/testing purposes: 1234# 1235# SND_DEBUG Enable extra debugging code that includes 1236# sanity checking and possible increase of 1237# verbosity. 1238# 1239# SND_DIAGNOSTIC Similar in a spirit of INVARIANTS/DIAGNOSTIC, 1240# zero tolerance against inconsistencies. 1241# 1242# SND_FEEDER_MULTIFORMAT By default, only 16/32 bit feeders are compiled 1243# in. This options enable most feeder converters 1244# except for 8bit. WARNING: May bloat the kernel. 1245# 1246# SND_FEEDER_FULL_MULTIFORMAT Ditto, but includes 8bit feeders as well. 1247# 1248# SND_FEEDER_RATE_HP (feeder_rate) High precision 64bit arithmetic 1249# as much as possible (the default trying to 1250# avoid it). Possible slowdown. 1251# 1252# SND_PCM_64 (Only applicable for i386/32bit arch) 1253# Process 32bit samples through 64bit 1254# integer/arithmetic. Slight increase of dynamic 1255# range at a cost of possible slowdown. 1256# 1257# SND_OLDSTEREO Only 2 channels are allowed, effectively 1258# disabling multichannel processing. 1259# 1260options SND_DEBUG 1261#options SND_DIAGNOSTIC 1262options SND_FEEDER_MULTIFORMAT 1263options SND_FEEDER_FULL_MULTIFORMAT 1264options SND_FEEDER_RATE_HP 1265options SND_PCM_64 1266options SND_OLDSTEREO 1267 1268# 1269# Miscellaneous hardware: 1270# 1271# bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board 1272# coremctl: Intel Core/E3 memory controller (required by ecc(4) and memtemp(4)) 1273# dimm: Location inforamtion (required by ecc(4) and memtemp(4)) 1274# ecc: ECC memory controller 1275# ipmi: Intelligent Platform Management Interface 1276# joy: joystick 1277# nrp: Comtrol Rocketport 1278# si: Specialix SI/XIO 4-32 port terminal multiplexor 1279# nmdm: nullmodem terminal driver (see nmdm(4)) 1280# tpm: Trusted Platform Module 1281 1282# Notes on the Specialix SI/XIO driver: 1283# **This is NOT a Specialix supported Driver!** 1284# The host card is memory, not IO mapped. 1285# The Rev 1 host cards use a 64K chunk, on a 32K boundary. 1286# The Rev 2 host cards use a 32K chunk, on a 32K boundary. 1287# The cards can use an IRQ of 11, 12 or 15. 1288 1289device coremctl 1290device dimm 1291device ecc 1292device joy0 at isa? port IO_GAME 1293device nrp 1294device si 1295# nullmodem terminal driver 1296device nmdm 1297device tpm 1298device ipmi 1299 1300# The `ahc' device provides support for the Adaptec 274X and 284X 1301# adapters. 1302device ahc 1303 1304# The aic7xxx driver will attempt to use memory mapped I/O for all PCI 1305# controllers that have it configured only if this option is set. Unfortunately, 1306# this doesn't work on some motherboards, which prevents it from being the 1307# default. 1308options AHC_ALLOW_MEMIO 1309 1310# The adw driver will attempt to use memory mapped I/O for all PCI 1311# controllers that have it configured only if this option is set. 1312options ADW_ALLOW_MEMIO 1313 1314# 1315# PCI devices & PCI options: 1316# 1317# The main PCI bus device is `pci'. It provides auto-detection and 1318# configuration support for all devices on the PCI bus, using either 1319# configuration mode defined in the PCI specification. 1320 1321device pci 1322 1323# PCI options 1324# 1325options COMPAT_OLDPCI #FreeBSD 2.2 and 3.x compatibility shims 1326 1327# AGP GART support 1328# 1329device agp 1330 1331# 1332# AGP debugging. 1333# 1334options AGP_DEBUG 1335 1336# The `ahc' device provides support for the Adaptec 29/3940(U)(W) 1337# and motherboard based AIC7870/AIC7880 adapters. 1338options AHC_DEBUG 1339options AHC_DEBUG_OPTS=0xffffffff 1340options AHC_REG_PRETTY_PRINT 1341options AHC_TMODE_ENABLE 1342# 1343# The 'ahd' device provides support for the Adaptec 79xx Ultra320 1344# SCSI adapters. Options are documented in the ahd(4) manpage: 1345options AHD_DEBUG 1346options AHD_DEBUG_OPTS=0xffffffff 1347options AHD_REG_PRETTY_PRINT 1348#options AHD_TMODE_ENABLE=0xff 1349# 1350# The `amd' device provides support for the AMD 53C974 SCSI host 1351# adapter chip as found on devices such as the Tekram DC-390(T). 1352# 1353# The `bge' device provides support for gigabit ethernet adapters 1354# based on the Broadcom BCM570x family of controllers, including the 1355# 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41, 1356# and the embedded gigE NICs on Dell PowerEdge 2550 servers. 1357# 1358# The `ncr' device provides support for the NCR 53C810 and 53C825 1359# self-contained SCSI host adapters. 1360# 1361# The `isp' device provides support for the Qlogic ISP 1020, 1040 1362# nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI, 1363# ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as 1364# the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters. 1365# 1366# The `dc' device provides support for PCI fast ethernet adapters 1367# based on the DEC/Intel 21143 and various workalikes including: 1368# the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics 1369# AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On 1370# 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II 1371# and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver 1372# replaces the old al, ax, dm, pn and mx drivers. List of brands: 1373# Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110, 1374# SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX, 1375# LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204, 1376# KNE110TX. 1377# 1378# The `de' device provides support for the Digital Equipment DC21040 1379# self-contained Ethernet adapter. 1380# 1381# The `em' device provides support for the Intel Pro/1000 Family of Gigabit 1382# adapters (82542, 82543, 82544, 82540). 1383# 1384# The `et' device provides support for the Agere ET1310 10/100/1000 PCIe 1385# adapters. 1386# 1387# The `fxp' device provides support for the Intel EtherExpress Pro/100B 1388# PCI Fast Ethernet adapters. 1389# 1390# The 'lge' device provides support for PCI gigabit ethernet adapters 1391# based on the Level 1 LXT1001 NetCellerator chipset. This includes the 1392# D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards. 1393# 1394# The 'my' device provides support for the Myson MTD80X and MTD89X PCI 1395# Fast Ethernet adapters. 1396# 1397# The 'nge' device provides support for PCI gigabit ethernet adapters 1398# based on the National Semiconductor DP83820 and DP83821 chipset. This 1399# includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante 1400# FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the 1401# LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T. 1402# 1403# The 'oce' device provides support for Emulex 10 Gbit adapters 1404# (OneConnect Ethernet). 1405# 1406# The 'pcn' device provides support for PCI fast ethernet adapters based 1407# on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+, 1408# PCnet/PRO and PCnet/Home. These were previously handled by the lnc 1409# driver (and still will be if you leave this driver out of the kernel). 1410# 1411# Te 're' device provides support for PCI GigaBit ethernet adapters based 1412# on the RealTek 8169 chipset. It also supports the 8139C+ and is the 1413# preferred driver for that chip. 1414# 1415# The 'rl' device provides support for PCI fast ethernet adapters based 1416# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults 1417# to using programmed I/O to do register accesses because memory mapped 1418# mode seems to cause severe lockups on SMP hardware. This driver also 1419# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called 1420# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek 1421# workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset 1422# and is supported by this driver, not the 'vr' driver. 1423# 1424# The 'sf' device provides support for Adaptec Duralink PCI fast 1425# ethernet adapters based on the Adaptec AIC-6915 "starfire" controller. 1426# This includes dual and quad port cards, as well as one 100baseFX card. 1427# Most of these are 64-bit PCI devices, except for one single port 1428# card which is 32-bit. 1429# 1430# The 'ste' device provides support for adapters based on the Sundance 1431# Technologies ST201 PCI fast ethernet controller. This includes the 1432# D-Link DFE-550TX. 1433# 1434# The 'sis' device provides support for adapters based on the Silicon 1435# Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller 1436# chips. 1437# 1438# The 'sk' device provides support for the SysKonnect SK-984x series 1439# PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842 1440# single port cards (single mode and multimode fiber) and the 1441# SK-9843 and SK-9844 dual port cards (also single mode and multimode). 1442# The driver will autodetect the number of ports on the card and 1443# attach each one as a separate network interface. 1444# 1445# The 'ti' device provides support for PCI gigabit ethernet NICs based 1446# on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the 1447# Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others. 1448# Note that you will probably want to bump up NMBCLUSTERS a lot to use 1449# this driver. 1450# 1451# The 'tl' device provides support for the Texas Instruments TNETE100 1452# series 'ThunderLAN' cards and integrated ethernet controllers. This 1453# includes several Compaq Netelligent 10/100 cards and the built-in 1454# ethernet controllers in several Compaq Prosignia, Proliant and 1455# Deskpro systems. It also supports several Olicom 10Mbps and 10/100 1456# boards. 1457# 1458# The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards. 1459# 1460# The `txp' device provides support for the 3Com 3cR990 "Typhoon" 1461# 10/100 adapters. 1462# 1463# The `vr' device provides support for various fast ethernet adapters 1464# based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II' 1465# chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking 1466# Technologies PN102TX, and the AOpen/Acer ALN-320. 1467# 1468# The `vx' device provides support for the 3Com 3C590 and 3C595 1469# early support 1470# 1471# The `wb' device provides support for various fast ethernet adapters 1472# based on the Winbond W89C840F chip. Note: this is not the same as 1473# the Winbond W89C940F, which is an NE2000 clone. 1474# 1475# The `xl' device provides support for the 3Com 3c900, 3c905 and 1476# 3c905B (Fast) Etherlink XL cards and integrated controllers. This 1477# includes the integrated 3c905B-TX chips in certain Dell Optiplex and 1478# Dell Precision desktop machines and the integrated 3c905-TX chips 1479# in Dell Latitude laptop docking stations. 1480# 1481# The 'bktr' device is a PCI video capture device using the Brooktree 1482# bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a 1483# TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator, 1484# Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo. 1485# 1486# options OVERRIDE_CARD=xxx 1487# options OVERRIDE_TUNER=xxx 1488# options OVERRIDE_MSP=1 1489# options OVERRIDE_DBX=1 1490# These options can be used to override the auto detection 1491# The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h 1492# Using sysctl(8) run-time overrides on a per-card basis can be made 1493# 1494# options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL 1495# or 1496# options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC 1497# Specifies the default video capture mode. 1498# This is required for Dual Crystal (28&35Mhz) boards where PAL is used 1499# to prevent hangs during initialisation. eg VideoLogic Captivator PCI. 1500# 1501# options BKTR_USE_PLL 1502# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal) 1503# must enable PLL mode with this option. eg some new Bt878 cards. 1504# 1505# options BKTR_GPIO_ACCESS 1506# This enable IOCTLs which give user level access to the GPIO port. 1507# 1508# options BKTR_NO_MSP_RESET 1509# Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first 1510# 1511# options BKTR_430_FX_MODE 1512# Switch Bt878/879 cards into Intel 430FX chipset compatibility mode. 1513# 1514# options BKTR_SIS_VIA_MODE 1515# Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is 1516# needed for some old SiS and VIA chipset motherboards. 1517# This also allows Bt878/879 chips to work on old OPTi (<1997) chipset 1518# motherboards and motherboards with bad or incomplete PCI 2.1 support. 1519# As a rough guess, old = before 1998 1520# 1521# options BKTR_NEW_MSP34XX_DRIVER 1522# Use new, more complete initialization scheme for the msp34* soundchip. 1523# Should fix stereo autodetection if the old driver does only output 1524# mono sound. 1525# 1526# options BKTR_OVERRIDE_CARD=xxx 1527# options BKTR_OVERRIDE_DBX=xxx 1528# options BKTR_OVERRIDE_MSP=xxx 1529# options BKTR_OVERRIDE_TUNER=xxx 1530# These options can be used to select a specific device, regardless of 1531# the autodetection and i2c device checks (see comments in bktr_card.c). 1532# 1533device ahc # AHA2940 and onboard AIC7xxx devices 1534device ahd # AIC79xx devices 1535device amd # AMD 53C974 (Tekram DC-390(T)) 1536device isp # Qlogic family 1537device ispfw # Firmware for QLogic HBAs 1538device mpt # LSI '909 FC adapters 1539device mps # LSI-Logic MPT-Fusion 2 1540device ncr # NCR/Symbios Logic 1541device sym # NCR/Symbios Logic (newer chipsets) 1542device trm # Tekram DC395U/UW/F and DC315U 1543# 1544# Options for ISP 1545# 1546# ISP_TARGET_MODE - enable target mode operation 1547#options ISP_TARGET_MODE=1 1548 1549# Options used in dev/disk/sym/ (Symbios SCSI driver). 1550#options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits) 1551 # Allows the ncr to take precedence 1552 # 1 (1<<0) -> 810a, 860 1553 # 2 (1<<1) -> 825a, 875, 885, 895 1554 # 4 (1<<2) -> 895a, 896, 1510d 1555#options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885 1556 # disabled:0 (default), enabled:1 1557#options SYM_SETUP_PCI_PARITY #-PCI parity checking 1558 # disabled:0, enabled:1 (default) 1559#options SYM_SETUP_MAX_LUN #-Number of LUNs supported 1560 # default:8, range:[1..64] 1561 1562 1563# MII bus support is required for some PCI 10/100 ethernet NICs, 1564# namely those which use MII-compliant transceivers or implement 1565# transceiver control interfaces that operate like an MII. Adding 1566# "device miibus0" to the kernel config pulls in support for 1567# the generic miibus API and all of the PHY drivers, including a 1568# generic one for PHYs that aren't specifically handled by an 1569# individual driver. 1570device miibus 1571 1572# PCI Ethernet NICs that use the common MII bus controller code. 1573device ae # Attansic/Atheros L2 Fast Ethernet 1574device alc # Atheros AR8131/AR8132 1575device ale # Atheros AR8121/AR8113/AR8114 1576device age # Attansic/Atheros L1 Gigabit Ethernet 1577device bce # Broadcom NetXtreme II Gigabit Ethernet 1578device bfe # Broadcom BCM440x 10/100 Ethernet 1579device bnx # Broadcom NetXtreme 5718/57785 Gigabit Ethernet 1580device dc # DEC/Intel 21143 and various workalikes 1581device fxp # Intel EtherExpress PRO/100B (82557, 82558) 1582device my # Myson Fast Ethernet (MTD80X, MTD89X) 1583device pcn # AMD Am79C97x PCI 10/100 NICs 1584device re # RealTek 8139C+/8169 1585device rl # RealTek 8129/8139 1586device sbsh # Granch SBNI16 SHDSL modem 1587device sf # Adaptec AIC-6915 (``Starfire'') 1588device sis # Silicon Integrated Systems SiS 900/SiS 7016 1589device ste # Sundance ST201 (D-Link DFE-550TX) 1590device tl # Texas Instruments ThunderLAN 1591device tx # SMC EtherPower II (83c17x ``EPIC'') 1592device vge # VIA 612x GigE 1593device vr # VIA Rhine, Rhine II 1594device wb # Winbond W89C840F 1595device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') 1596 1597# PCI Ethernet NICs. 1598device de # DEC/Intel DC21x4x (``Tulip'') 1599device txp # 3Com 3cR990 (``Typhoon'') 1600device vx # 3Com 3c590, 3c595 (``Vortex'') 1601 1602# Gigabit Ethernet NICs. 1603device bge # Broadcom BCM570x (``Tigon III'') 1604device em # Intel Pro/1000 (8254x,8257x) 1605 # Requires ig_hal 1606device emx # Intel Pro/1000 (8257{1,2,3,4}) 1607 # Requires ig_hal 1608device igb # Intel Pro/1000 (82575, 82576, 82580, i350) 1609 # Requires ig_hal 1610device ig_hal # Intel Pro/1000 hardware abstraction layer 1611device ix # Intel PRO/10GbE PCIE Ethernet Family 1612device et # Agere ET1310 10/100/1000 Ethernet 1613device lge # Level 1 LXT1001 (``Mercury'') 1614device mxge # Myricom Myri-10G 10GbE NIC 1615device nfe # nVidia nForce2/3 MCP04/51/55 CK804 1616device nge # NatSemi DP83820 and DP83821 1617device oce # Emulex 10 GbE (OneConnect Ethernet) 1618device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link 1619device ti # Alteon (``Tigon I'', ``Tigon II'') 1620device stge # Sundance/Tamarack TC9021 Gigabit Ethernet 1621device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet 1622device jme # JMicron Gigabit/Fast Ethernet 1623 1624# Brooktree driver has been ported to the new I2C framework. Thus, 1625# you'll need to have the following 3 lines in the kernel config. 1626# device smbus 1627# device iicbus 1628# device iicbb 1629# The iic and smb devices are only needed if you want to control other 1630# I2C slaves connected to the external connector of some cards. 1631# 1632device bktr 1633options BKTR_NEW_MSP34XX_DRIVER 1634 1635# WinTV PVR-250/350 driver 1636device cxm 1637 1638# 1639# PCCARD/PCMCIA 1640# 1641# pccard: pccard slots 1642# cardbus/cbb: cardbus bridge 1643device pccard 1644device cardbus 1645device cbb 1646 1647# 1648# MMC/SD 1649# 1650# mmc MMC/SD bus 1651# mmcsd MMC/SD memory card 1652# sdhci Generic PCI SD Host Controller 1653# 1654device mmc 1655device mmcsd 1656device sdhci 1657 1658# 1659# SMB bus 1660# 1661# System Management Bus support is provided by the 'smbus' device. 1662# Access to the SMBus device is via the 'smb' device (/dev/smb*), 1663# which is a child of the 'smbus' device. 1664# 1665# Supported devices: 1666# smb standard io through /dev/smb* 1667# 1668# Supported SMB interfaces: 1669# iicsmb I2C to SMB bridge with any iicbus interface 1670# bktr brooktree848 I2C hardware interface 1671# intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit 1672# alpm Acer Aladdin-IV/V/Pro2 Power Management Unit 1673# ichiic Intel generation 4 I2C controller 1674# ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA) 1675# viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers 1676# amdpm AMD 756 Power Management Unit 1677# amdsmb AMD 8111 SMBus 2.0 Controller 1678# 1679device smbus # Bus support, required for smb below. 1680 1681device intpm 1682device alpm 1683device ichiic 1684device ichsmb 1685device viapm 1686device amdpm 1687device amdsmb 1688 1689device smb 1690 1691# 1692# I2C Bus 1693# 1694# Philips i2c bus support is provided by the `iicbus' device. 1695# 1696# Supported devices: 1697# ic i2c network interface 1698# iic i2c standard io 1699# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands. 1700# 1701# Supported interfaces: 1702# pcf Philips PCF8584 ISA-bus controller 1703# bktr brooktree848 I2C software interface 1704# 1705# Other: 1706# iicbb generic I2C bit-banging code (needed by lpbb, bktr) 1707# 1708device iicbus # Bus support, required for ic/iic/iicsmb below. 1709device iicbb 1710 1711device ic 1712device iic 1713device iicsmb # smb over i2c bridge 1714 1715device pcf0 at isa? port 0x320 irq 5 1716 1717# Intel performance-energy bias 1718device perfbias 1719 1720# Intel software controlled clock modulation 1721device clockmod 1722 1723# Intel Sandy Bridge and newer CPUs power usage estimation 1724device corepower 1725 1726# Intel Core and newer CPUs on-die digital thermal sensor support 1727device coretemp 1728 1729# Memory thermal sensor 1730device memtemp 1731 1732# CPU control pseudo-device. Provides access to MSRs, CPUID info and 1733# microcode update feature. 1734device cpuctl 1735 1736# Effective CPU frequency interface via APERF/MPERF MSRs 1737device aperf 1738 1739# AMD Family 0Fh, 10h and 11h temperature sensors 1740device kate 1741device km 1742 1743# ThinkPad Active Protection System accelerometer 1744device aps0 at isa? port 0x1600 1745 1746# HW monitoring devices lm(4), it(4) and nsclpcsio. 1747device lm0 at isa? port 0x290 1748device it0 at isa? port 0x290 1749device it1 at isa? port 0xc00 1750device it2 at isa? port 0xd00 1751device it3 at isa? port 0x228 1752device nsclpcsio0 at isa? port 0x2e 1753device nsclpcsio1 at isa? port 0x4e 1754device wbsio0 at isa? port 0x2e 1755device wbsio1 at isa? port 0x4e 1756device uguru0 at isa? port 0xe0 # ABIT uGuru 1757 1758# Parallel-Port Bus 1759# 1760# Parallel port bus support is provided by the `ppbus' device. 1761# Multiple devices may be attached to the parallel port, devices 1762# are automatically probed and attached when found. 1763# 1764# Supported devices: 1765# vpo Iomega Zip Drive 1766# Requires SCSI disk support ('scbus' and 'da'); the best 1767# performance is achieved with ports in EPP 1.9 mode. 1768# lpt Parallel Printer 1769# plip Parallel network interface 1770# ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O 1771# pps Pulse per second Timing Interface 1772# lpbb Philips official parallel port I2C bit-banging interface 1773# 1774# Supported interfaces: 1775# ppc ISA-bus parallel port interfaces. 1776# 1777 1778options PPC_PROBE_CHIPSET # Enable chipset specific detection 1779 # (see flags in ppc(4)) 1780options DEBUG_1284 # IEEE1284 signaling protocol debug 1781options PERIPH_1284 # Makes your computer act as a IEEE1284 1782 # compliant peripheral 1783options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices 1784options VP0_DEBUG # ZIP/ZIP+ debug 1785options LPT_DEBUG # Printer driver debug 1786options PPC_DEBUG=2 # Parallel chipset level debug 1787options PLIP_DEBUG # Parallel network IP interface debug 1788options PCFCLOCK_VERBOSE # Verbose pcfclock driver 1789options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10) 1790 1791device ppc0 at isa? irq 7 1792device ppbus 1793device vpo 1794device lpt 1795device plip 1796device ppi 1797device pps 1798device lpbb 1799device pcfclock 1800 1801# Kernel BOOTP support 1802 1803options BOOTP # Use BOOTP to obtain IP address/hostname 1804options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info 1805options BOOTP_COMPAT # Workaround for broken bootp daemons. 1806options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP 1807 1808# 1809# Set the number of PV entries per process. Increasing this can 1810# stop panics related to heavy use of shared memory. However, that can 1811# (combined with large amounts of physical memory) cause panics at 1812# boot time due the kernel running out of VM space. 1813# 1814# If you're tweaking this, you might also want to increase the sysctls 1815# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target". 1816# 1817# The value below is the one more than the default. 1818# 1819options PMAP_SHPGPERPROC=201 1820 1821# 1822# Disable swapping. This option removes all code which actually performs 1823# swapping, so it's not possible to turn it back on at run-time. 1824# 1825# This is sometimes usable for systems which don't have any swap space 1826# (see also sysctls "vm.defer_swapspace_pageouts" and 1827# "vm.disable_swapspace_pageouts") 1828# 1829#options NO_SWAPPING 1830 1831# Set the size of the buffer cache KVM reservation, in buffers. This is 1832# scaled by approximately 16384 bytes. The system will auto-size the buffer 1833# cache if this option is not specified. 1834# 1835options NBUF=512 1836 1837# Set the size of the mbuf KVM reservation, in clusters. This is scaled 1838# by approximately 2048 bytes. The system will auto-size the mbuf area 1839# to (512 + maxusers*16) if this option is not specified. 1840# maxusers is in turn computed at boot time depending on available memory 1841# or set to the value specified by "options MAXUSERS=x" (x=0 means 1842# autoscaling). 1843# So, to take advantage of autoscaling, you have to remove both 1844# NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config. 1845# 1846options NMBCLUSTERS=1024 1847 1848# Set the number of mbufs available in the system. Each mbuf 1849# consumes 256 bytes. The system will autosize this (to 4 times 1850# the number of NMBCLUSTERS, depending on other constraints) 1851# if this option is not specified. 1852# 1853options NMBUFS=4096 1854 1855# Tune the buffer cache maximum KVA reservation, in bytes. The maximum is 1856# usually capped at 200 MB, effecting machines with > 1GB of ram. Note 1857# that the buffer cache only really governs write buffering and disk block 1858# translations. The VM page cache is our primary disk cache and is not 1859# effected by the size of the buffer cache. 1860# 1861options VM_BCACHE_SIZE_MAX="(100*1024*1024)" 1862 1863# Tune the swap zone KVA reservation, in bytes. The default is typically 1864# 70 MB, giving the system the ability to manage a maximum of 28GB worth 1865# of swapped out data. 1866# 1867options VM_SWZONE_SIZE_MAX="(50*1024*1024)" 1868 1869# 1870# Enable extra debugging code for locks. This stores the filename and 1871# line of whatever acquired the lock in the lock itself, and change a 1872# number of function calls to pass around the relevant data. This is 1873# not at all useful unless you are debugging lock code. Also note 1874# that it is likely to break e.g. fstat(1) unless you recompile your 1875# userland with -DDEBUG_LOCKS as well. 1876# 1877# DEBUG_LOCKS_LATENCY adds a sysctl to add a forced latency loop 1878# (count to N) in front of any spinlock or gettoken. 1879# 1880options DEBUG_LOCKS 1881options DEBUG_LOCKS_LATENCY 1882 1883# Set the amount of time (in seconds) the system will wait before 1884# rebooting automatically when a kernel panic occurs. If set to (-1), 1885# the system will wait indefinitely until a key is pressed on the 1886# console. 1887options PANIC_REBOOT_WAIT_TIME=16 1888 1889# Attempt to bypass the buffer cache and put data directly into the 1890# userland buffer for read operation when O_DIRECT flag is set on the 1891# file. Both offset and length of the read operation must be 1892# multiples of the physical media sector size. 1893# 1894options DIRECTIO 1895 1896# Specify a lower limit for the number of swap I/O buffers. They are 1897# (among other things) used when bypassing the buffer cache due to 1898# DIRECTIO kernel option enabled and O_DIRECT flag set on file. 1899# 1900#options NSWBUF_MIN=120 1901 1902# The 'asr' driver provides support for current DPT/Adaptec SCSI RAID 1903# controllers (SmartRAID V and VI and later). 1904# These controllers require the CAM infrastructure. 1905# 1906device asr 1907 1908# The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/). 1909# These have hardware RAID-{0,1,5} support, and do multi-initiator I/O. 1910# The DPT controllers are commonly re-licensed under other brand-names - 1911# some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and 1912# Compaq are actually DPT controllers. 1913# 1914# See src/sys/dev/raid/dpt for debugging and other subtle options. 1915# DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various 1916# instruments are enabled. The tools in 1917# /usr/sbin/dpt_* assume these to be enabled. 1918# DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT. 1919# If you ant the driver to handle timeouts, enable 1920# this option. If your system is very busy, this 1921# option will create more trouble than solve. 1922# DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to 1923# wait when timing out with the above option. 1924# DPT_DEBUG_xxxx These are controllable from sys/dev/raid/dpt/dpt.h 1925# DPT_LOST_IRQ When enabled, will try, once per second, to catch 1926# any interrupt that got lost. Seems to help in some 1927# DPT-firmware/Motherboard combinations. Minimal 1928# cost, great benefit. 1929# DPT_RESET_HBA Make "reset" actually reset the controller 1930# instead of fudging it. Only enable this if you 1931# are 100% certain you need it. 1932 1933device dpt 1934 1935# DPT options 1936#!CAM# options DPT_MEASURE_PERFORMANCE 1937#!CAM# options DPT_HANDLE_TIMEOUTS 1938options DPT_TIMEOUT_FACTOR=4 1939options DPT_LOST_IRQ 1940options DPT_RESET_HBA 1941 1942# 1943# Compaq "CISS" RAID controllers (SmartRAID 5* series) 1944# These controllers have a SCSI-like interface, and require the 1945# CAM infrastructure. 1946# 1947device ciss 1948 1949# 1950# Intel Integrated RAID controllers. 1951# This driver is supported and maintained by 1952# "Leubner, Achim" <Achim_Leubner@adaptec.com>. 1953# 1954device iir 1955 1956# 1957# Mylex AcceleRAID and eXtremeRAID controllers with v6 and later 1958# firmware. These controllers have a SCSI-like interface, and require 1959# the CAM infrastructure. 1960# 1961device mly 1962 1963# USB support 1964# 1965 1966# UHCI controller 1967device uhci 1968# OHCI controller 1969device ohci 1970# EHCI controller 1971device ehci 1972# XHCI controller 1973device xhci 1974# General USB code (mandatory for USB) 1975device usb 1976# Human Interface Device (anything with buttons and dials) 1977device uhid 1978# USB keyboard 1979device ukbd 1980# USB printer 1981device ulpt 1982# USB mass storage (Requires scbus and da) 1983device umass 1984# USB mass storage driver for device-side mode 1985device usfs 1986# USB modem support 1987device umodem 1988# USB mouse 1989device ums 1990# eGalax USB touch screen 1991device uep 1992# Diamond Rio 500 MP3 player 1993device urio 1994# USB com devices 1995device "u3g" 1996device uark 1997device ubsa 1998device ubser 1999device uchcom 2000device ucom 2001device ucycom 2002device ufoma 2003device uftdi 2004device ugensa 2005device uipaq 2006device umcs 2007device umct 2008device umoscom 2009device uplcom 2010device uslcom 2011device uvisor 2012device uvscom 2013 2014# 2015# USB ethernet support 2016device uether 2017# 2018# ADMtek USB ethernet. Supports the LinkSys USB100TX, 2019# the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX 2020# and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus 2021# eval board. 2022device aue 2023# 2024# ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the 2025# LinkSys USB200M and various other adapters. 2026device axe 2027# 2028# ASIX Electronics AX88178A/AX88179 USB 2.0/3.0 gigabit ethernet driver. 2029device axge 2030# 2031# CATC USB-EL1201A USB ethernet. Supports the CATC Netmate 2032# and Netmate II, and the Belkin F5U111. 2033device cue 2034# 2035# USB Apple iPhone/iPad tethered Ethernet driver 2036device ipheth 2037# 2038# Kawasaki LSI ethernet. Supports the LinkSys USB10T, 2039# Entrega USB-NET-E45, Peracom Ethernet Adapter, the 2040# 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T, 2041# the Netgear EA101, the D-Link DSB-650, the SMC 2102USB 2042# and 2104USB, and the Corega USB-T. 2043device kue 2044# 2045# Moschip MCS7730/MCS7840 USB to fast ethernet. Supports the Sitecom LN030. 2046device mos 2047# 2048# Davicom DM9601E USB to fast ethernet. Supports the Corega FEther USB-TXC. 2049device udav 2050 2051# USB wireless NICs, requires wlan_amrr 2052# 2053# Ralink Technology RT2501USB/RT2601USB 2054device rum 2055# 2056# Ralink Technology RT2700U/RT2800U/RT3000U wireless driver 2057device run 2058device runfw 2059# 2060# RNDIS USB ethernet driver 2061device urndis 2062# 2063# Realtek RTL8188CU/RTL8192CU wireless driver 2064device urtwn 2065device urtwnfw 2066 2067# Fm Radio 2068# 2069device ufm 2070 2071# Templates for programming USB device side drivers 2072# 2073device usb_template 2074 2075# debugging options for the USB subsystem 2076# 2077options USB_DEBUG 2078 2079# options for ukbd: 2080options UKBD_DFLT_KEYMAP # specify the built-in keymap 2081makeoptions UKBD_DFLT_KEYMAP=it.iso 2082 2083# Firewire support 2084device firewire # Firewire bus code 2085device sbp # SCSI over Firewire (Requires scbus and da) 2086device fwe # Ethernet over Firewire (non-standard!) 2087 2088# dcons support (Dumb Console Device) 2089device dcons # dumb console driver 2090device dcons_crom # FireWire attachment 2091options DCONS_BUF_SIZE=16384 # buffer size 2092options DCONS_POLL_HZ=100 # polling rate 2093options DCONS_FORCE_CONSOLE=1 # force to be the primary console 2094options DCONS_FORCE_GDB=1 # force to be the gdb device 2095 2096##################################################################### 2097# crypto subsystem 2098# 2099# This is a port of the openbsd crypto framework. Include this when 2100# configuring IPsec and when you have a h/w crypto device to accelerate 2101# user applications that link to openssl. 2102# 2103# Drivers are ports from openbsd with some simple enhancements that have 2104# been fed back to openbsd (and hopefully will be included). 2105 2106device crypto # core crypto support 2107device cryptodev # /dev/crypto for access to h/w 2108 2109device rndtest # FIPS 140-2 entropy tester 2110 2111device hifn # Hifn 7951, 7781, etc. 2112options HIFN_DEBUG # enable debugging support: hw.hifn.debug 2113#options HIFN_NO_RNG # for devices without RNG 2114options HIFN_RNDTEST # enable rndtest support 2115 2116device safe # SafeNet 1141 2117options SAFE_DEBUG # enable debugging support: hw.safe.debug 2118#options SAFE_NO_RNG # for devices without RNG 2119options SAFE_RNDTEST # enable rndtest support 2120 2121device ubsec # Broadcom 5501, 5601, 58xx 2122options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug 2123#options UBSEC_NO_RNG # for devices without RNG 2124options UBSEC_RNDTEST # enable rndtest support 2125 2126device aesni # hardware crypto/RNG for AES-NI 2127device padlock # hardware crypto/RNG for VIA C3/C7/Eden 2128device rdrand # hardware RNG for RdRand 2129 2130# 2131# ACPI support using the Intel ACPI Component Architecture reference 2132# implementation. 2133# 2134# ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer 2135# kernel environment variables to select initial debugging levels for the 2136# Intel ACPICA code. 2137# 2138# Note that building ACPI into the kernel is deprecated; the module is 2139# normally loaded automatically by the loader. 2140 2141device acpi 2142options ACPI_DEBUG 2143 2144# ACPI WMI Mapping driver 2145device acpi_wmi 2146 2147# ACPI Asus Extras (LCD backlight/brightness, video output, etc.) 2148device acpi_asus 2149 2150# ACPI Fujitsu Extras (Buttons) 2151device acpi_fujitsu 2152 2153# ACPI extras driver for HP laptops 2154device acpi_hp 2155 2156# ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.) 2157device acpi_panasonic 2158 2159# ACPI Sony extra (LCD brightness) 2160device acpi_sony 2161 2162# ACPI extras driver for ThinkPad laptops 2163device acpi_thinkpad 2164 2165# ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.) 2166device acpi_toshiba 2167 2168# ACPI Video Extensions (LCD backlight/brightness, video output, etc.) 2169device acpi_video 2170 2171# ACPI Docking Station 2172device acpi_dock 2173 2174device aibs # ASUSTeK AI Booster (ACPI ASOC ATK0110) 2175 2176# DRM options: 2177# drm: General DRM code 2178# i915kms: Intel integrated GPUs, starting from the 830M family 2179# radeonkms: ATI Radeon cards 2180# 2181# DRM_DEBUG: include debug printfs, very slow 2182# 2183# DRM requires AGP in the kernel. 2184 2185device drm 2186#device "i915kms" # breaks VGA console, disabled by default 2187#device radeonkms # breaks VGA console, disabled by default 2188 2189options DRM_DEBUG 2190options DRM_LINUX 2191 2192# 2193# Misc devices 2194# 2195device cmx # Omnikey CardMan 4040 smartcard reader 2196device amdsbwd # AMD South Bridge watchdog 2197device gpio # Enable support for the gpio framework 2198device ichwd # Intel ICH watchdog interrupt timer 2199device tbridge # regression testing 2200 2201# 2202# Virtio support 2203# 2204device virtio 2205device virtio_blk 2206device vtnet 2207device virtio_pci 2208 2209# 2210# Embedded system options: 2211# 2212# An embedded system might want to run something other than init. 2213options INIT_PATH="/sbin/init:/sbin/oinit" 2214 2215# Debug options 2216options BUS_DEBUG # enable newbus debugging 2217options RSS_DEBUG # enable RSS (Receive Side Scaling) debugging 2218 2219# Record the program counter of the code interrupted by the statistics 2220# clock interrupt. Use pctrack(8) to dump this information. 2221options DEBUG_PCTRACK 2222 2223# More undocumented options for linting. 2224# Note that documenting these are not considered an affront. 2225 2226#options ACPI_NO_SEMAPHORES 2227options AHC_DUMP_EEPROM 2228#options BKTR_ALLOC_PAGES=xxx 2229options CAM_DEBUG_DELAY 2230options CLUSTERDEBUG 2231#options COMPAT_LINUX 2232options DEBUG 2233options DEBUG_CRIT_SECTIONS 2234#options DISABLE_PSE 2235options BCE_RSS_DEBUG 2236options BCE_TSS_DEBUG 2237options BNX_RSS_DEBUG 2238options BNX_TSO_DEBUG 2239options BNX_TSS_DEBUG 2240options EMX_RSS_DEBUG 2241options EMX_TSO_DEBUG 2242options EMX_TSS_DEBUG 2243options JME_RSS_DEBUG 2244options IGB_RSS_DEBUG 2245options IGB_TSS_DEBUG 2246options IGB_MSIX_DEBUG 2247options IX_RSS_DEBUG 2248options ENABLE_ALART 2249options FB_DEBUG=2 2250options FB_INSTALL_CDEV 2251options I586_PMC_GUPROF=0x70000 2252#options IEEE80211_DEBUG_REFCNT 2253options IEEE80211_SUPPORT_SUPERG 2254options KBDIO_DEBUG=10 2255options KBD_MAXRETRY=4 2256options KBD_MAXWAIT=6 2257options KBD_RESETDELAY=201 2258#options KERN_TIMESTAMP 2259options KEY 2260#options LINPROCFS 2261options LOCKF_DEBUG 2262#options MAXFILES=xxx 2263options MBUF_DEBUG 2264options NO_LWKT_SPLIT_USERPRI 2265options PANIC_DEBUG 2266options PMAP_DEBUG 2267options PSM_DEBUG=4 2268options SCSI_NCR_DEBUG 2269options SCSI_NCR_MAX_SYNC=10000 2270options SCSI_NCR_MAX_WIDE=1 2271options SCSI_NCR_MYADDR=7 2272options SHOW_BUSYBUFS # List buffers that prevent root unmount 2273options SI_DEBUG 2274options SLAB_DEBUG 2275options SLIP_IFF_OPTS 2276options SOCKBUF_DEBUG 2277options TDMA_BINTVAL_DEFAULT=5 2278options TDMA_SLOTCNT_DEFAULT=2 2279options TDMA_SLOTLEN_DEFAULT=10*1000 2280options TDMA_TXRATE_11A_DEFAULT=2*24 2281options TDMA_TXRATE_11B_DEFAULT=2*11 2282options TDMA_TXRATE_11G_DEFAULT=2*24 2283options TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)" 2284options TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)" 2285options TDMA_TXRATE_HALF_DEFAULT=2*12 2286options TDMA_TXRATE_QUARTER_DEFAULT=2*6 2287options TDMA_TXRATE_TURBO_DEFAULT=2*24 2288#options TIMER_FREQ="((14318182+6)/12)" 2289options VFS_BIO_DEBUG 2290options VM_PAGE_DEBUG 2291options XBONEHACK 2292 2293options KTR 2294options KTR_ALL 2295options KTR_ENTRIES=1024 2296options KTR_VERBOSE=1 2297#options KTR_ACPI_EC 2298#options KTR_CTXSW 2299#options KTR_DMCRYPT 2300#options KTR_DSCHED_BFQ 2301#options KTR_ETHERNET 2302#options KTR_HAMMER 2303#options KTR_IFQ 2304#options KTR_IF_BGE 2305#options KTR_IF_EM 2306#options KTR_IF_EMX 2307#options KTR_IF_POLL 2308#options KTR_IF_START 2309#options KTR_IPIQ 2310#options KTR_KERNENTRY 2311#options KTR_MEMORY 2312#options KTR_SERIALIZER 2313#options KTR_SOWAKEUP 2314#options KTR_SPIN_CONTENTION 2315#options KTR_TESTLOG 2316#options KTR_TOKENS 2317#options KTR_TSLEEP 2318#options KTR_UDP 2319#options KTR_USCHED_BSD4 2320#options KTR_USCHED_DFLY 2321 2322# ALTQ 2323options ALTQ #alternate queueing 2324options ALTQ_CBQ #class based queueing 2325options ALTQ_RED #random early detection 2326options ALTQ_RIO #triple red for diffserv (needs RED) 2327options ALTQ_HFSC #hierarchical fair service curve 2328options ALTQ_PRIQ #priority queue 2329options ALTQ_FAIRQ #fair queue 2330#options ALTQ_NOPCC #don't use processor cycle counter 2331options ALTQ_DEBUG #for debugging 2332# you might want to set kernel timer to 1kHz if you use CBQ, 2333# especially with 100baseT 2334#options HZ=1000 2335 2336# DSCHED stuff 2337options DSCHED_AS 2338options DSCHED_BFQ 2339options DSCHED_FQ 2340 2341# WATCHDOG 2342options WDOG_DISABLE_ON_PANIC # Automatically disable watchdogs on panic 2343 2344# LED 2345options ERROR_LED_ON_PANIC # If an error led is present, light it up on panic 2346