1 /* 2 * Generic driver for the BusLogic MultiMaster SCSI host adapters 3 * Product specific probe and attach routines can be found in: 4 * sys/dev/buslogic/bt_isa.c BT-54X, BT-445 cards 5 * sys/dev/buslogic/bt_mca.c BT-64X, SDC3211B, SDC3211F 6 * sys/dev/buslogic/bt_eisa.c BT-74X, BT-75x cards, SDC3222F 7 * sys/dev/buslogic/bt_pci.c BT-946, BT-948, BT-956, BT-958 cards 8 * 9 * Copyright (c) 1998, 1999 Justin T. Gibbs. 10 * All rights reserved. 11 * 12 * Redistribution and use in source and binary forms, with or without 13 * modification, are permitted provided that the following conditions 14 * are met: 15 * 1. Redistributions of source code must retain the above copyright 16 * notice, this list of conditions, and the following disclaimer, 17 * without modification, immediately at the beginning of the file. 18 * 2. The name of the author may not be used to endorse or promote products 19 * derived from this software without specific prior written permission. 20 * 21 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 22 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 23 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 24 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR 25 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 26 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 27 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 28 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 29 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 30 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 31 * SUCH DAMAGE. 32 * 33 * $FreeBSD: src/sys/dev/buslogic/bt.c,v 1.25.2.1 2000/08/02 22:32:26 peter Exp $ 34 * $DragonFly: src/sys/dev/disk/buslogic/bt.c,v 1.6 2004/03/15 01:10:43 dillon Exp $ 35 */ 36 37 /* 38 * Special thanks to Leonard N. Zubkoff for writing such a complete and 39 * well documented Mylex/BusLogic MultiMaster driver for Linux. Support 40 * in this driver for the wide range of MultiMaster controllers and 41 * firmware revisions, with their otherwise undocumented quirks, would not 42 * have been possible without his efforts. 43 */ 44 45 #include <sys/param.h> 46 #include <sys/systm.h> 47 #include <sys/malloc.h> 48 #include <sys/buf.h> 49 #include <sys/kernel.h> 50 #include <sys/sysctl.h> 51 #include <sys/bus.h> 52 53 /* 54 * XXX It appears that BusLogic PCI adapters go out to lunch if you 55 * attempt to perform memory mapped I/O. 56 */ 57 #if 0 58 #include "use_pci.h" 59 #if NPCI > 0 60 #include <machine/bus_memio.h> 61 #endif 62 #endif 63 #include <machine/bus_pio.h> 64 #include <machine/bus.h> 65 #include <machine/clock.h> 66 #include <sys/rman.h> 67 68 #include <bus/cam/cam.h> 69 #include <bus/cam/cam_ccb.h> 70 #include <bus/cam/cam_sim.h> 71 #include <bus/cam/cam_xpt_sim.h> 72 #include <bus/cam/cam_debug.h> 73 74 #include <bus/cam/scsi/scsi_message.h> 75 76 #include <vm/vm.h> 77 #include <vm/pmap.h> 78 79 #include "btreg.h" 80 81 /* MailBox Management functions */ 82 static __inline void btnextinbox(struct bt_softc *bt); 83 static __inline void btnextoutbox(struct bt_softc *bt); 84 85 static __inline void 86 btnextinbox(struct bt_softc *bt) 87 { 88 if (bt->cur_inbox == bt->last_inbox) 89 bt->cur_inbox = bt->in_boxes; 90 else 91 bt->cur_inbox++; 92 } 93 94 static __inline void 95 btnextoutbox(struct bt_softc *bt) 96 { 97 if (bt->cur_outbox == bt->last_outbox) 98 bt->cur_outbox = bt->out_boxes; 99 else 100 bt->cur_outbox++; 101 } 102 103 /* CCB Mangement functions */ 104 static __inline u_int32_t btccbvtop(struct bt_softc *bt, 105 struct bt_ccb *bccb); 106 static __inline struct bt_ccb* btccbptov(struct bt_softc *bt, 107 u_int32_t ccb_addr); 108 static __inline u_int32_t btsensepaddr(struct bt_softc *bt, 109 struct bt_ccb *bccb); 110 static __inline struct scsi_sense_data* btsensevaddr(struct bt_softc *bt, 111 struct bt_ccb *bccb); 112 113 static __inline u_int32_t 114 btccbvtop(struct bt_softc *bt, struct bt_ccb *bccb) 115 { 116 return (bt->bt_ccb_physbase 117 + (u_int32_t)((caddr_t)bccb - (caddr_t)bt->bt_ccb_array)); 118 } 119 120 static __inline struct bt_ccb * 121 btccbptov(struct bt_softc *bt, u_int32_t ccb_addr) 122 { 123 return (bt->bt_ccb_array + 124 ((struct bt_ccb*)ccb_addr-(struct bt_ccb*)bt->bt_ccb_physbase)); 125 } 126 127 static __inline u_int32_t 128 btsensepaddr(struct bt_softc *bt, struct bt_ccb *bccb) 129 { 130 u_int index; 131 132 index = (u_int)(bccb - bt->bt_ccb_array); 133 return (bt->sense_buffers_physbase 134 + (index * sizeof(struct scsi_sense_data))); 135 } 136 137 static __inline struct scsi_sense_data * 138 btsensevaddr(struct bt_softc *bt, struct bt_ccb *bccb) 139 { 140 u_int index; 141 142 index = (u_int)(bccb - bt->bt_ccb_array); 143 return (bt->sense_buffers + index); 144 } 145 146 static __inline struct bt_ccb* btgetccb(struct bt_softc *bt); 147 static __inline void btfreeccb(struct bt_softc *bt, 148 struct bt_ccb *bccb); 149 static void btallocccbs(struct bt_softc *bt); 150 static bus_dmamap_callback_t btexecuteccb; 151 static void btdone(struct bt_softc *bt, struct bt_ccb *bccb, 152 bt_mbi_comp_code_t comp_code); 153 154 /* Host adapter command functions */ 155 static int btreset(struct bt_softc* bt, int hard_reset); 156 157 /* Initialization functions */ 158 static int btinitmboxes(struct bt_softc *bt); 159 static bus_dmamap_callback_t btmapmboxes; 160 static bus_dmamap_callback_t btmapccbs; 161 static bus_dmamap_callback_t btmapsgs; 162 163 /* Transfer Negotiation Functions */ 164 static void btfetchtransinfo(struct bt_softc *bt, 165 struct ccb_trans_settings *cts); 166 167 /* CAM SIM entry points */ 168 #define ccb_bccb_ptr spriv_ptr0 169 #define ccb_bt_ptr spriv_ptr1 170 static void btaction(struct cam_sim *sim, union ccb *ccb); 171 static void btpoll(struct cam_sim *sim); 172 173 /* Our timeout handler */ 174 timeout_t bttimeout; 175 176 u_long bt_unit = 0; 177 178 /* 179 * XXX 180 * Do our own re-probe protection until a configuration 181 * manager can do it for us. This ensures that we don't 182 * reprobe a card already found by the EISA or PCI probes. 183 */ 184 struct bt_isa_port bt_isa_ports[] = 185 { 186 { 0x130, 0, 4 }, 187 { 0x134, 0, 5 }, 188 { 0x230, 0, 2 }, 189 { 0x234, 0, 3 }, 190 { 0x330, 0, 0 }, 191 { 0x334, 0, 1 } 192 }; 193 194 /* 195 * I/O ports listed in the order enumerated by the 196 * card for certain op codes. 197 */ 198 u_int16_t bt_board_ports[] = 199 { 200 0x330, 201 0x334, 202 0x230, 203 0x234, 204 0x130, 205 0x134 206 }; 207 208 /* Exported functions */ 209 void 210 bt_init_softc(device_t dev, struct resource *port, 211 struct resource *irq, struct resource *drq) 212 { 213 struct bt_softc *bt = device_get_softc(dev); 214 215 SLIST_INIT(&bt->free_bt_ccbs); 216 LIST_INIT(&bt->pending_ccbs); 217 SLIST_INIT(&bt->sg_maps); 218 bt->dev = dev; 219 bt->unit = device_get_unit(dev); 220 bt->port = port; 221 bt->irq = irq; 222 bt->drq = drq; 223 bt->tag = rman_get_bustag(port); 224 bt->bsh = rman_get_bushandle(port); 225 } 226 227 void 228 bt_free_softc(device_t dev) 229 { 230 struct bt_softc *bt = device_get_softc(dev); 231 232 switch (bt->init_level) { 233 default: 234 case 11: 235 bus_dmamap_unload(bt->sense_dmat, bt->sense_dmamap); 236 case 10: 237 bus_dmamem_free(bt->sense_dmat, bt->sense_buffers, 238 bt->sense_dmamap); 239 case 9: 240 bus_dma_tag_destroy(bt->sense_dmat); 241 case 8: 242 { 243 struct sg_map_node *sg_map; 244 245 while ((sg_map = SLIST_FIRST(&bt->sg_maps))!= NULL) { 246 SLIST_REMOVE_HEAD(&bt->sg_maps, links); 247 bus_dmamap_unload(bt->sg_dmat, 248 sg_map->sg_dmamap); 249 bus_dmamem_free(bt->sg_dmat, sg_map->sg_vaddr, 250 sg_map->sg_dmamap); 251 free(sg_map, M_DEVBUF); 252 } 253 bus_dma_tag_destroy(bt->sg_dmat); 254 } 255 case 7: 256 bus_dmamap_unload(bt->ccb_dmat, bt->ccb_dmamap); 257 case 6: 258 bus_dmamem_free(bt->ccb_dmat, bt->bt_ccb_array, 259 bt->ccb_dmamap); 260 bus_dmamap_destroy(bt->ccb_dmat, bt->ccb_dmamap); 261 case 5: 262 bus_dma_tag_destroy(bt->ccb_dmat); 263 case 4: 264 bus_dmamap_unload(bt->mailbox_dmat, bt->mailbox_dmamap); 265 case 3: 266 bus_dmamem_free(bt->mailbox_dmat, bt->in_boxes, 267 bt->mailbox_dmamap); 268 bus_dmamap_destroy(bt->mailbox_dmat, bt->mailbox_dmamap); 269 case 2: 270 bus_dma_tag_destroy(bt->buffer_dmat); 271 case 1: 272 bus_dma_tag_destroy(bt->mailbox_dmat); 273 case 0: 274 break; 275 } 276 } 277 278 int 279 bt_port_probe(device_t dev, struct bt_probe_info *info) 280 { 281 struct bt_softc *bt = device_get_softc(dev); 282 config_data_t config_data; 283 int error; 284 285 /* See if there is really a card present */ 286 if (bt_probe(dev) || bt_fetch_adapter_info(dev)) 287 return(1); 288 289 /* 290 * Determine our IRQ, and DMA settings and 291 * export them to the configuration system. 292 */ 293 error = bt_cmd(bt, BOP_INQUIRE_CONFIG, NULL, /*parmlen*/0, 294 (u_int8_t*)&config_data, sizeof(config_data), 295 DEFAULT_CMD_TIMEOUT); 296 if (error != 0) { 297 printf("bt_port_probe: Could not determine IRQ or DMA " 298 "settings for adapter.\n"); 299 return (1); 300 } 301 302 if (bt->model[0] == '5') { 303 /* DMA settings only make sense for ISA cards */ 304 switch (config_data.dma_chan) { 305 case DMA_CHAN_5: 306 info->drq = 5; 307 break; 308 case DMA_CHAN_6: 309 info->drq = 6; 310 break; 311 case DMA_CHAN_7: 312 info->drq = 7; 313 break; 314 default: 315 printf("bt_port_probe: Invalid DMA setting " 316 "detected for adapter.\n"); 317 return (1); 318 } 319 } else { 320 /* VL/EISA/PCI DMA */ 321 info->drq = -1; 322 } 323 switch (config_data.irq) { 324 case IRQ_9: 325 case IRQ_10: 326 case IRQ_11: 327 case IRQ_12: 328 case IRQ_14: 329 case IRQ_15: 330 info->irq = ffs(config_data.irq) + 8; 331 break; 332 default: 333 printf("bt_port_probe: Invalid IRQ setting %x" 334 "detected for adapter.\n", config_data.irq); 335 return (1); 336 } 337 return (0); 338 } 339 340 /* 341 * Probe the adapter and verify that the card is a BusLogic. 342 */ 343 int 344 bt_probe(device_t dev) 345 { 346 struct bt_softc *bt = device_get_softc(dev); 347 esetup_info_data_t esetup_info; 348 u_int status; 349 u_int intstat; 350 u_int geometry; 351 int error; 352 u_int8_t param; 353 354 /* 355 * See if the three I/O ports look reasonable. 356 * Touch the minimal number of registers in the 357 * failure case. 358 */ 359 status = bt_inb(bt, STATUS_REG); 360 if ((status == 0) 361 || (status & (DIAG_ACTIVE|CMD_REG_BUSY| 362 STATUS_REG_RSVD|CMD_INVALID)) != 0) { 363 if (bootverbose) 364 device_printf(dev, "Failed Status Reg Test - %x\n", 365 status); 366 return (ENXIO); 367 } 368 369 intstat = bt_inb(bt, INTSTAT_REG); 370 if ((intstat & INTSTAT_REG_RSVD) != 0) { 371 device_printf(dev, "Failed Intstat Reg Test\n"); 372 return (ENXIO); 373 } 374 375 geometry = bt_inb(bt, GEOMETRY_REG); 376 if (geometry == 0xFF) { 377 if (bootverbose) 378 device_printf(dev, "Failed Geometry Reg Test\n"); 379 return (ENXIO); 380 } 381 382 /* 383 * Looking good so far. Final test is to reset the 384 * adapter and attempt to fetch the extended setup 385 * information. This should filter out all 1542 cards. 386 */ 387 if ((error = btreset(bt, /*hard_reset*/TRUE)) != 0) { 388 if (bootverbose) 389 device_printf(dev, "Failed Reset\n"); 390 return (ENXIO); 391 } 392 393 param = sizeof(esetup_info); 394 error = bt_cmd(bt, BOP_INQUIRE_ESETUP_INFO, ¶m, /*parmlen*/1, 395 (u_int8_t*)&esetup_info, sizeof(esetup_info), 396 DEFAULT_CMD_TIMEOUT); 397 if (error != 0) { 398 return (ENXIO); 399 } 400 401 return (0); 402 } 403 404 /* 405 * Pull the boards setup information and record it in our softc. 406 */ 407 int 408 bt_fetch_adapter_info(device_t dev) 409 { 410 struct bt_softc *bt = device_get_softc(dev); 411 board_id_data_t board_id; 412 esetup_info_data_t esetup_info; 413 config_data_t config_data; 414 int error; 415 u_int8_t length_param; 416 417 /* First record the firmware version */ 418 error = bt_cmd(bt, BOP_INQUIRE_BOARD_ID, NULL, /*parmlen*/0, 419 (u_int8_t*)&board_id, sizeof(board_id), 420 DEFAULT_CMD_TIMEOUT); 421 if (error != 0) { 422 device_printf(dev, "bt_fetch_adapter_info - Failed Get Board Info\n"); 423 return (error); 424 } 425 bt->firmware_ver[0] = board_id.firmware_rev_major; 426 bt->firmware_ver[1] = '.'; 427 bt->firmware_ver[2] = board_id.firmware_rev_minor; 428 bt->firmware_ver[3] = '\0'; 429 430 /* 431 * Depending on the firmware major and minor version, 432 * we may be able to fetch additional minor version info. 433 */ 434 if (bt->firmware_ver[0] > '0') { 435 436 error = bt_cmd(bt, BOP_INQUIRE_FW_VER_3DIG, NULL, /*parmlen*/0, 437 (u_int8_t*)&bt->firmware_ver[3], 1, 438 DEFAULT_CMD_TIMEOUT); 439 if (error != 0) { 440 device_printf(dev, 441 "bt_fetch_adapter_info - Failed Get " 442 "Firmware 3rd Digit\n"); 443 return (error); 444 } 445 if (bt->firmware_ver[3] == ' ') 446 bt->firmware_ver[3] = '\0'; 447 bt->firmware_ver[4] = '\0'; 448 } 449 450 if (strcmp(bt->firmware_ver, "3.3") >= 0) { 451 452 error = bt_cmd(bt, BOP_INQUIRE_FW_VER_4DIG, NULL, /*parmlen*/0, 453 (u_int8_t*)&bt->firmware_ver[4], 1, 454 DEFAULT_CMD_TIMEOUT); 455 if (error != 0) { 456 device_printf(dev, 457 "bt_fetch_adapter_info - Failed Get " 458 "Firmware 4th Digit\n"); 459 return (error); 460 } 461 if (bt->firmware_ver[4] == ' ') 462 bt->firmware_ver[4] = '\0'; 463 bt->firmware_ver[5] = '\0'; 464 } 465 466 /* 467 * Some boards do not handle the "recently documented" 468 * Inquire Board Model Number command correctly or do not give 469 * exact information. Use the Firmware and Extended Setup 470 * information in these cases to come up with the right answer. 471 * The major firmware revision number indicates: 472 * 473 * 5.xx BusLogic "W" Series Host Adapters: 474 * BT-948/958/958D 475 * 4.xx BusLogic "C" Series Host Adapters: 476 * BT-946C/956C/956CD/747C/757C/757CD/445C/545C/540CF 477 * 3.xx BusLogic "S" Series Host Adapters: 478 * BT-747S/747D/757S/757D/445S/545S/542D 479 * BT-542B/742A (revision H) 480 * 2.xx BusLogic "A" Series Host Adapters: 481 * BT-542B/742A (revision G and below) 482 * 0.xx AMI FastDisk VLB/EISA BusLogic Clone Host Adapter 483 */ 484 length_param = sizeof(esetup_info); 485 error = bt_cmd(bt, BOP_INQUIRE_ESETUP_INFO, &length_param, /*parmlen*/1, 486 (u_int8_t*)&esetup_info, sizeof(esetup_info), 487 DEFAULT_CMD_TIMEOUT); 488 if (error != 0) { 489 return (error); 490 } 491 492 bt->bios_addr = esetup_info.bios_addr << 12; 493 494 if (esetup_info.bus_type == 'A' 495 && bt->firmware_ver[0] == '2') { 496 snprintf(bt->model, sizeof(bt->model), "542B"); 497 } else if (esetup_info.bus_type == 'E' 498 && (strncmp(bt->firmware_ver, "2.1", 3) == 0 499 || strncmp(bt->firmware_ver, "2.20", 4) == 0)) { 500 snprintf(bt->model, sizeof(bt->model), "742A"); 501 } else if (esetup_info.bus_type == 'E' 502 && bt->firmware_ver[0] == '0') { 503 /* AMI FastDisk EISA Series 441 0.x */ 504 snprintf(bt->model, sizeof(bt->model), "747A"); 505 } else { 506 ha_model_data_t model_data; 507 int i; 508 509 length_param = sizeof(model_data); 510 error = bt_cmd(bt, BOP_INQUIRE_MODEL, &length_param, 1, 511 (u_int8_t*)&model_data, sizeof(model_data), 512 DEFAULT_CMD_TIMEOUT); 513 if (error != 0) { 514 device_printf(dev, 515 "bt_fetch_adapter_info - Failed Inquire " 516 "Model Number\n"); 517 return (error); 518 } 519 for (i = 0; i < sizeof(model_data.ascii_model); i++) { 520 bt->model[i] = model_data.ascii_model[i]; 521 if (bt->model[i] == ' ') 522 break; 523 } 524 bt->model[i] = '\0'; 525 } 526 527 bt->level_trigger_ints = esetup_info.level_trigger_ints ? 1 : 0; 528 529 /* SG element limits */ 530 bt->max_sg = esetup_info.max_sg; 531 532 /* Set feature flags */ 533 bt->wide_bus = esetup_info.wide_bus; 534 bt->diff_bus = esetup_info.diff_bus; 535 bt->ultra_scsi = esetup_info.ultra_scsi; 536 537 if ((bt->firmware_ver[0] == '5') 538 || (bt->firmware_ver[0] == '4' && bt->wide_bus)) 539 bt->extended_lun = TRUE; 540 541 bt->strict_rr = (strcmp(bt->firmware_ver, "3.31") >= 0); 542 543 bt->extended_trans = 544 ((bt_inb(bt, GEOMETRY_REG) & EXTENDED_TRANSLATION) != 0); 545 546 /* 547 * Determine max CCB count and whether tagged queuing is 548 * available based on controller type. Tagged queuing 549 * only works on 'W' series adapters, 'C' series adapters 550 * with firmware of rev 4.42 and higher, and 'S' series 551 * adapters with firmware of rev 3.35 and higher. The 552 * maximum CCB counts are as follows: 553 * 554 * 192 BT-948/958/958D 555 * 100 BT-946C/956C/956CD/747C/757C/757CD/445C 556 * 50 BT-545C/540CF 557 * 30 BT-747S/747D/757S/757D/445S/545S/542D/542B/742A 558 */ 559 if (bt->firmware_ver[0] == '5') { 560 bt->max_ccbs = 192; 561 bt->tag_capable = TRUE; 562 } else if (bt->firmware_ver[0] == '4') { 563 if (bt->model[0] == '5') 564 bt->max_ccbs = 50; 565 else 566 bt->max_ccbs = 100; 567 bt->tag_capable = (strcmp(bt->firmware_ver, "4.22") >= 0); 568 } else { 569 bt->max_ccbs = 30; 570 if (bt->firmware_ver[0] == '3' 571 && (strcmp(bt->firmware_ver, "3.35") >= 0)) 572 bt->tag_capable = TRUE; 573 else 574 bt->tag_capable = FALSE; 575 } 576 577 if (bt->tag_capable != FALSE) 578 bt->tags_permitted = ALL_TARGETS; 579 580 /* Determine Sync/Wide/Disc settings */ 581 if (bt->firmware_ver[0] >= '4') { 582 auto_scsi_data_t auto_scsi_data; 583 fetch_lram_params_t fetch_lram_params; 584 int error; 585 586 /* 587 * These settings are stored in the 588 * AutoSCSI data in LRAM of 'W' and 'C' 589 * adapters. 590 */ 591 fetch_lram_params.offset = AUTO_SCSI_BYTE_OFFSET; 592 fetch_lram_params.response_len = sizeof(auto_scsi_data); 593 error = bt_cmd(bt, BOP_FETCH_LRAM, 594 (u_int8_t*)&fetch_lram_params, 595 sizeof(fetch_lram_params), 596 (u_int8_t*)&auto_scsi_data, 597 sizeof(auto_scsi_data), DEFAULT_CMD_TIMEOUT); 598 599 if (error != 0) { 600 device_printf(dev, 601 "bt_fetch_adapter_info - Failed " 602 "Get Auto SCSI Info\n"); 603 return (error); 604 } 605 606 bt->disc_permitted = auto_scsi_data.low_disc_permitted 607 | (auto_scsi_data.high_disc_permitted << 8); 608 bt->sync_permitted = auto_scsi_data.low_sync_permitted 609 | (auto_scsi_data.high_sync_permitted << 8); 610 bt->fast_permitted = auto_scsi_data.low_fast_permitted 611 | (auto_scsi_data.high_fast_permitted << 8); 612 bt->ultra_permitted = auto_scsi_data.low_ultra_permitted 613 | (auto_scsi_data.high_ultra_permitted << 8); 614 bt->wide_permitted = auto_scsi_data.low_wide_permitted 615 | (auto_scsi_data.high_wide_permitted << 8); 616 617 if (bt->ultra_scsi == FALSE) 618 bt->ultra_permitted = 0; 619 620 if (bt->wide_bus == FALSE) 621 bt->wide_permitted = 0; 622 } else { 623 /* 624 * 'S' and 'A' series have this information in the setup 625 * information structure. 626 */ 627 setup_data_t setup_info; 628 629 length_param = sizeof(setup_info); 630 error = bt_cmd(bt, BOP_INQUIRE_SETUP_INFO, &length_param, 631 /*paramlen*/1, (u_int8_t*)&setup_info, 632 sizeof(setup_info), DEFAULT_CMD_TIMEOUT); 633 634 if (error != 0) { 635 device_printf(dev, 636 "bt_fetch_adapter_info - Failed " 637 "Get Setup Info\n"); 638 return (error); 639 } 640 641 if (setup_info.initiate_sync != 0) { 642 bt->sync_permitted = ALL_TARGETS; 643 644 if (bt->model[0] == '7') { 645 if (esetup_info.sync_neg10MB != 0) 646 bt->fast_permitted = ALL_TARGETS; 647 if (strcmp(bt->model, "757") == 0) 648 bt->wide_permitted = ALL_TARGETS; 649 } 650 } 651 bt->disc_permitted = ALL_TARGETS; 652 } 653 654 /* We need as many mailboxes as we can have ccbs */ 655 bt->num_boxes = bt->max_ccbs; 656 657 /* Determine our SCSI ID */ 658 659 error = bt_cmd(bt, BOP_INQUIRE_CONFIG, NULL, /*parmlen*/0, 660 (u_int8_t*)&config_data, sizeof(config_data), 661 DEFAULT_CMD_TIMEOUT); 662 if (error != 0) { 663 device_printf(dev, 664 "bt_fetch_adapter_info - Failed Get Config\n"); 665 return (error); 666 } 667 bt->scsi_id = config_data.scsi_id; 668 669 return (0); 670 } 671 672 /* 673 * Start the board, ready for normal operation 674 */ 675 int 676 bt_init(device_t dev) 677 { 678 struct bt_softc *bt = device_get_softc(dev); 679 680 /* Announce the Adapter */ 681 device_printf(dev, "BT-%s FW Rev. %s ", bt->model, bt->firmware_ver); 682 683 if (bt->ultra_scsi != 0) 684 printf("Ultra "); 685 686 if (bt->wide_bus != 0) 687 printf("Wide "); 688 else 689 printf("Narrow "); 690 691 if (bt->diff_bus != 0) 692 printf("Diff "); 693 694 printf("SCSI Host Adapter, SCSI ID %d, %d CCBs\n", bt->scsi_id, 695 bt->max_ccbs); 696 697 /* 698 * Create our DMA tags. These tags define the kinds of device 699 * accessible memory allocations and memory mappings we will 700 * need to perform during normal operation. 701 * 702 * Unless we need to further restrict the allocation, we rely 703 * on the restrictions of the parent dmat, hence the common 704 * use of MAXADDR and MAXSIZE. 705 */ 706 707 /* DMA tag for mapping buffers into device visible space. */ 708 if (bus_dma_tag_create(bt->parent_dmat, /*alignment*/1, /*boundary*/0, 709 /*lowaddr*/BUS_SPACE_MAXADDR, 710 /*highaddr*/BUS_SPACE_MAXADDR, 711 /*filter*/NULL, /*filterarg*/NULL, 712 /*maxsize*/MAXBSIZE, /*nsegments*/BT_NSEG, 713 /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, 714 /*flags*/BUS_DMA_ALLOCNOW, 715 &bt->buffer_dmat) != 0) { 716 goto error_exit; 717 } 718 719 bt->init_level++; 720 /* DMA tag for our mailboxes */ 721 if (bus_dma_tag_create(bt->parent_dmat, /*alignment*/1, /*boundary*/0, 722 /*lowaddr*/BUS_SPACE_MAXADDR, 723 /*highaddr*/BUS_SPACE_MAXADDR, 724 /*filter*/NULL, /*filterarg*/NULL, 725 bt->num_boxes * (sizeof(bt_mbox_in_t) 726 + sizeof(bt_mbox_out_t)), 727 /*nsegments*/1, 728 /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, 729 /*flags*/0, &bt->mailbox_dmat) != 0) { 730 goto error_exit; 731 } 732 733 bt->init_level++; 734 735 /* Allocation for our mailboxes */ 736 if (bus_dmamem_alloc(bt->mailbox_dmat, (void **)&bt->out_boxes, 737 BUS_DMA_NOWAIT, &bt->mailbox_dmamap) != 0) { 738 goto error_exit; 739 } 740 741 bt->init_level++; 742 743 /* And permanently map them */ 744 bus_dmamap_load(bt->mailbox_dmat, bt->mailbox_dmamap, 745 bt->out_boxes, 746 bt->num_boxes * (sizeof(bt_mbox_in_t) 747 + sizeof(bt_mbox_out_t)), 748 btmapmboxes, bt, /*flags*/0); 749 750 bt->init_level++; 751 752 bt->in_boxes = (bt_mbox_in_t *)&bt->out_boxes[bt->num_boxes]; 753 754 btinitmboxes(bt); 755 756 /* DMA tag for our ccb structures */ 757 if (bus_dma_tag_create(bt->parent_dmat, /*alignment*/1, /*boundary*/0, 758 /*lowaddr*/BUS_SPACE_MAXADDR, 759 /*highaddr*/BUS_SPACE_MAXADDR, 760 /*filter*/NULL, /*filterarg*/NULL, 761 bt->max_ccbs * sizeof(struct bt_ccb), 762 /*nsegments*/1, 763 /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, 764 /*flags*/0, &bt->ccb_dmat) != 0) { 765 goto error_exit; 766 } 767 768 bt->init_level++; 769 770 /* Allocation for our ccbs */ 771 if (bus_dmamem_alloc(bt->ccb_dmat, (void **)&bt->bt_ccb_array, 772 BUS_DMA_NOWAIT, &bt->ccb_dmamap) != 0) { 773 goto error_exit; 774 } 775 776 bt->init_level++; 777 778 /* And permanently map them */ 779 bus_dmamap_load(bt->ccb_dmat, bt->ccb_dmamap, 780 bt->bt_ccb_array, 781 bt->max_ccbs * sizeof(struct bt_ccb), 782 btmapccbs, bt, /*flags*/0); 783 784 bt->init_level++; 785 786 /* DMA tag for our S/G structures. We allocate in page sized chunks */ 787 if (bus_dma_tag_create(bt->parent_dmat, /*alignment*/1, /*boundary*/0, 788 /*lowaddr*/BUS_SPACE_MAXADDR, 789 /*highaddr*/BUS_SPACE_MAXADDR, 790 /*filter*/NULL, /*filterarg*/NULL, 791 PAGE_SIZE, /*nsegments*/1, 792 /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, 793 /*flags*/0, &bt->sg_dmat) != 0) { 794 goto error_exit; 795 } 796 797 bt->init_level++; 798 799 /* Perform initial CCB allocation */ 800 bzero(bt->bt_ccb_array, bt->max_ccbs * sizeof(struct bt_ccb)); 801 btallocccbs(bt); 802 803 if (bt->num_ccbs == 0) { 804 device_printf(dev, 805 "bt_init - Unable to allocate initial ccbs\n"); 806 goto error_exit; 807 } 808 809 /* 810 * Note that we are going and return (to probe) 811 */ 812 return 0; 813 814 error_exit: 815 816 return (ENXIO); 817 } 818 819 int 820 bt_attach(device_t dev) 821 { 822 struct bt_softc *bt = device_get_softc(dev); 823 int tagged_dev_openings; 824 struct cam_devq *devq; 825 int error; 826 827 /* 828 * We reserve 1 ccb for error recovery, so don't 829 * tell the XPT about it. 830 */ 831 if (bt->tag_capable != 0) 832 tagged_dev_openings = bt->max_ccbs - 1; 833 else 834 tagged_dev_openings = 0; 835 836 /* 837 * Create the device queue for our SIM. 838 */ 839 devq = cam_simq_alloc(bt->max_ccbs - 1); 840 if (devq == NULL) 841 return (ENOMEM); 842 843 /* 844 * Construct our SIM entry 845 */ 846 bt->sim = cam_sim_alloc(btaction, btpoll, "bt", bt, bt->unit, 847 2, tagged_dev_openings, devq); 848 cam_simq_release(devq); 849 if (bt->sim == NULL) 850 return (ENOMEM); 851 852 if (xpt_bus_register(bt->sim, 0) != CAM_SUCCESS) { 853 cam_sim_free(bt->sim); 854 return (ENXIO); 855 } 856 857 if (xpt_create_path(&bt->path, /*periph*/NULL, 858 cam_sim_path(bt->sim), CAM_TARGET_WILDCARD, 859 CAM_LUN_WILDCARD) != CAM_REQ_CMP) { 860 xpt_bus_deregister(cam_sim_path(bt->sim)); 861 cam_sim_free(bt->sim); 862 return (ENXIO); 863 } 864 865 /* 866 * Setup interrupt. 867 */ 868 error = bus_setup_intr(dev, bt->irq, INTR_TYPE_CAM, 869 bt_intr, bt, &bt->ih); 870 if (error) { 871 device_printf(dev, "bus_setup_intr() failed: %d\n", error); 872 return (error); 873 } 874 875 return (0); 876 } 877 878 int 879 bt_check_probed_iop(u_int ioport) 880 { 881 u_int i; 882 883 for (i = 0; i < BT_NUM_ISAPORTS; i++) { 884 if (bt_isa_ports[i].addr == ioport) { 885 if (bt_isa_ports[i].probed != 0) 886 return (1); 887 else { 888 return (0); 889 } 890 } 891 } 892 return (1); 893 } 894 895 void 896 bt_mark_probed_bio(isa_compat_io_t port) 897 { 898 if (port < BIO_DISABLED) 899 bt_mark_probed_iop(bt_board_ports[port]); 900 } 901 902 void 903 bt_mark_probed_iop(u_int ioport) 904 { 905 u_int i; 906 907 for (i = 0; i < BT_NUM_ISAPORTS; i++) { 908 if (ioport == bt_isa_ports[i].addr) { 909 bt_isa_ports[i].probed = 1; 910 break; 911 } 912 } 913 } 914 915 void 916 bt_find_probe_range(int ioport, int *port_index, int *max_port_index) 917 { 918 if (ioport > 0) { 919 int i; 920 921 for (i = 0;i < BT_NUM_ISAPORTS; i++) 922 if (ioport <= bt_isa_ports[i].addr) 923 break; 924 if ((i >= BT_NUM_ISAPORTS) 925 || (ioport != bt_isa_ports[i].addr)) { 926 printf("\nbt_isa_probe: Invalid baseport of 0x%x specified.\n" 927 "bt_isa_probe: Nearest valid baseport is 0x%x.\n" 928 "bt_isa_probe: Failing probe.\n", 929 ioport, 930 (i < BT_NUM_ISAPORTS) 931 ? bt_isa_ports[i].addr 932 : bt_isa_ports[BT_NUM_ISAPORTS - 1].addr); 933 *port_index = *max_port_index = -1; 934 return; 935 } 936 *port_index = *max_port_index = bt_isa_ports[i].bio; 937 } else { 938 *port_index = 0; 939 *max_port_index = BT_NUM_ISAPORTS - 1; 940 } 941 } 942 943 int 944 bt_iop_from_bio(isa_compat_io_t bio_index) 945 { 946 if (bio_index >= 0 && bio_index < BT_NUM_ISAPORTS) 947 return (bt_board_ports[bio_index]); 948 return (-1); 949 } 950 951 952 static void 953 btallocccbs(struct bt_softc *bt) 954 { 955 struct bt_ccb *next_ccb; 956 struct sg_map_node *sg_map; 957 bus_addr_t physaddr; 958 bt_sg_t *segs; 959 int newcount; 960 int i; 961 962 if (bt->num_ccbs >= bt->max_ccbs) 963 /* Can't allocate any more */ 964 return; 965 966 next_ccb = &bt->bt_ccb_array[bt->num_ccbs]; 967 968 sg_map = malloc(sizeof(*sg_map), M_DEVBUF, M_WAITOK); 969 970 /* Allocate S/G space for the next batch of CCBS */ 971 if (bus_dmamem_alloc(bt->sg_dmat, (void **)&sg_map->sg_vaddr, 972 BUS_DMA_NOWAIT, &sg_map->sg_dmamap) != 0) { 973 free(sg_map, M_DEVBUF); 974 goto error_exit; 975 } 976 977 SLIST_INSERT_HEAD(&bt->sg_maps, sg_map, links); 978 979 bus_dmamap_load(bt->sg_dmat, sg_map->sg_dmamap, sg_map->sg_vaddr, 980 PAGE_SIZE, btmapsgs, bt, /*flags*/0); 981 982 segs = sg_map->sg_vaddr; 983 physaddr = sg_map->sg_physaddr; 984 985 newcount = (PAGE_SIZE / (BT_NSEG * sizeof(bt_sg_t))); 986 for (i = 0; bt->num_ccbs < bt->max_ccbs && i < newcount; i++) { 987 int error; 988 989 next_ccb->sg_list = segs; 990 next_ccb->sg_list_phys = physaddr; 991 next_ccb->flags = BCCB_FREE; 992 error = bus_dmamap_create(bt->buffer_dmat, /*flags*/0, 993 &next_ccb->dmamap); 994 if (error != 0) 995 break; 996 SLIST_INSERT_HEAD(&bt->free_bt_ccbs, next_ccb, links); 997 segs += BT_NSEG; 998 physaddr += (BT_NSEG * sizeof(bt_sg_t)); 999 next_ccb++; 1000 bt->num_ccbs++; 1001 } 1002 1003 /* Reserve a CCB for error recovery */ 1004 if (bt->recovery_bccb == NULL) { 1005 bt->recovery_bccb = SLIST_FIRST(&bt->free_bt_ccbs); 1006 SLIST_REMOVE_HEAD(&bt->free_bt_ccbs, links); 1007 } 1008 1009 if (SLIST_FIRST(&bt->free_bt_ccbs) != NULL) 1010 return; 1011 1012 error_exit: 1013 device_printf(bt->dev, "Can't malloc BCCBs\n"); 1014 } 1015 1016 static __inline void 1017 btfreeccb(struct bt_softc *bt, struct bt_ccb *bccb) 1018 { 1019 int s; 1020 1021 s = splcam(); 1022 if ((bccb->flags & BCCB_ACTIVE) != 0) 1023 LIST_REMOVE(&bccb->ccb->ccb_h, sim_links.le); 1024 if (bt->resource_shortage != 0 1025 && (bccb->ccb->ccb_h.status & CAM_RELEASE_SIMQ) == 0) { 1026 bccb->ccb->ccb_h.status |= CAM_RELEASE_SIMQ; 1027 bt->resource_shortage = FALSE; 1028 } 1029 bccb->flags = BCCB_FREE; 1030 SLIST_INSERT_HEAD(&bt->free_bt_ccbs, bccb, links); 1031 bt->active_ccbs--; 1032 splx(s); 1033 } 1034 1035 static __inline struct bt_ccb* 1036 btgetccb(struct bt_softc *bt) 1037 { 1038 struct bt_ccb* bccb; 1039 int s; 1040 1041 s = splcam(); 1042 if ((bccb = SLIST_FIRST(&bt->free_bt_ccbs)) != NULL) { 1043 SLIST_REMOVE_HEAD(&bt->free_bt_ccbs, links); 1044 bt->active_ccbs++; 1045 } else { 1046 btallocccbs(bt); 1047 bccb = SLIST_FIRST(&bt->free_bt_ccbs); 1048 if (bccb != NULL) { 1049 SLIST_REMOVE_HEAD(&bt->free_bt_ccbs, links); 1050 bt->active_ccbs++; 1051 } 1052 } 1053 splx(s); 1054 1055 return (bccb); 1056 } 1057 1058 static void 1059 btaction(struct cam_sim *sim, union ccb *ccb) 1060 { 1061 struct bt_softc *bt; 1062 1063 CAM_DEBUG(ccb->ccb_h.path, CAM_DEBUG_TRACE, ("btaction\n")); 1064 1065 bt = (struct bt_softc *)cam_sim_softc(sim); 1066 1067 switch (ccb->ccb_h.func_code) { 1068 /* Common cases first */ 1069 case XPT_SCSI_IO: /* Execute the requested I/O operation */ 1070 case XPT_RESET_DEV: /* Bus Device Reset the specified SCSI device */ 1071 { 1072 struct bt_ccb *bccb; 1073 struct bt_hccb *hccb; 1074 1075 /* 1076 * get a bccb to use. 1077 */ 1078 if ((bccb = btgetccb(bt)) == NULL) { 1079 int s; 1080 1081 s = splcam(); 1082 bt->resource_shortage = TRUE; 1083 splx(s); 1084 xpt_freeze_simq(bt->sim, /*count*/1); 1085 ccb->ccb_h.status = CAM_REQUEUE_REQ; 1086 xpt_done(ccb); 1087 return; 1088 } 1089 1090 hccb = &bccb->hccb; 1091 1092 /* 1093 * So we can find the BCCB when an abort is requested 1094 */ 1095 bccb->ccb = ccb; 1096 ccb->ccb_h.ccb_bccb_ptr = bccb; 1097 ccb->ccb_h.ccb_bt_ptr = bt; 1098 1099 /* 1100 * Put all the arguments for the xfer in the bccb 1101 */ 1102 hccb->target_id = ccb->ccb_h.target_id; 1103 hccb->target_lun = ccb->ccb_h.target_lun; 1104 hccb->btstat = 0; 1105 hccb->sdstat = 0; 1106 1107 if (ccb->ccb_h.func_code == XPT_SCSI_IO) { 1108 struct ccb_scsiio *csio; 1109 struct ccb_hdr *ccbh; 1110 1111 csio = &ccb->csio; 1112 ccbh = &csio->ccb_h; 1113 hccb->opcode = INITIATOR_CCB_WRESID; 1114 hccb->datain = (ccb->ccb_h.flags & CAM_DIR_IN) ? 1 : 0; 1115 hccb->dataout =(ccb->ccb_h.flags & CAM_DIR_OUT) ? 1 : 0; 1116 hccb->cmd_len = csio->cdb_len; 1117 if (hccb->cmd_len > sizeof(hccb->scsi_cdb)) { 1118 ccb->ccb_h.status = CAM_REQ_INVALID; 1119 btfreeccb(bt, bccb); 1120 xpt_done(ccb); 1121 return; 1122 } 1123 hccb->sense_len = csio->sense_len; 1124 if ((ccbh->flags & CAM_TAG_ACTION_VALID) != 0 1125 && ccb->csio.tag_action != CAM_TAG_ACTION_NONE) { 1126 hccb->tag_enable = TRUE; 1127 hccb->tag_type = (ccb->csio.tag_action & 0x3); 1128 } else { 1129 hccb->tag_enable = FALSE; 1130 hccb->tag_type = 0; 1131 } 1132 if ((ccbh->flags & CAM_CDB_POINTER) != 0) { 1133 if ((ccbh->flags & CAM_CDB_PHYS) == 0) { 1134 bcopy(csio->cdb_io.cdb_ptr, 1135 hccb->scsi_cdb, hccb->cmd_len); 1136 } else { 1137 /* I guess I could map it in... */ 1138 ccbh->status = CAM_REQ_INVALID; 1139 btfreeccb(bt, bccb); 1140 xpt_done(ccb); 1141 return; 1142 } 1143 } else { 1144 bcopy(csio->cdb_io.cdb_bytes, 1145 hccb->scsi_cdb, hccb->cmd_len); 1146 } 1147 /* If need be, bounce our sense buffer */ 1148 if (bt->sense_buffers != NULL) { 1149 hccb->sense_addr = btsensepaddr(bt, bccb); 1150 } else { 1151 hccb->sense_addr = vtophys(&csio->sense_data); 1152 } 1153 /* 1154 * If we have any data to send with this command, 1155 * map it into bus space. 1156 */ 1157 /* Only use S/G if there is a transfer */ 1158 if ((ccbh->flags & CAM_DIR_MASK) != CAM_DIR_NONE) { 1159 if ((ccbh->flags & CAM_SCATTER_VALID) == 0) { 1160 /* 1161 * We've been given a pointer 1162 * to a single buffer. 1163 */ 1164 if ((ccbh->flags & CAM_DATA_PHYS)==0) { 1165 int s; 1166 int error; 1167 1168 s = splsoftvm(); 1169 error = bus_dmamap_load( 1170 bt->buffer_dmat, 1171 bccb->dmamap, 1172 csio->data_ptr, 1173 csio->dxfer_len, 1174 btexecuteccb, 1175 bccb, 1176 /*flags*/0); 1177 if (error == EINPROGRESS) { 1178 /* 1179 * So as to maintain 1180 * ordering, freeze the 1181 * controller queue 1182 * until our mapping is 1183 * returned. 1184 */ 1185 xpt_freeze_simq(bt->sim, 1186 1); 1187 csio->ccb_h.status |= 1188 CAM_RELEASE_SIMQ; 1189 } 1190 splx(s); 1191 } else { 1192 struct bus_dma_segment seg; 1193 1194 /* Pointer to physical buffer */ 1195 seg.ds_addr = 1196 (bus_addr_t)csio->data_ptr; 1197 seg.ds_len = csio->dxfer_len; 1198 btexecuteccb(bccb, &seg, 1, 0); 1199 } 1200 } else { 1201 struct bus_dma_segment *segs; 1202 1203 if ((ccbh->flags & CAM_DATA_PHYS) != 0) 1204 panic("btaction - Physical " 1205 "segment pointers " 1206 "unsupported"); 1207 1208 if ((ccbh->flags&CAM_SG_LIST_PHYS)==0) 1209 panic("btaction - Virtual " 1210 "segment addresses " 1211 "unsupported"); 1212 1213 /* Just use the segments provided */ 1214 segs = (struct bus_dma_segment *) 1215 csio->data_ptr; 1216 btexecuteccb(bccb, segs, 1217 csio->sglist_cnt, 0); 1218 } 1219 } else { 1220 btexecuteccb(bccb, NULL, 0, 0); 1221 } 1222 } else { 1223 hccb->opcode = INITIATOR_BUS_DEV_RESET; 1224 /* No data transfer */ 1225 hccb->datain = TRUE; 1226 hccb->dataout = TRUE; 1227 hccb->cmd_len = 0; 1228 hccb->sense_len = 0; 1229 hccb->tag_enable = FALSE; 1230 hccb->tag_type = 0; 1231 btexecuteccb(bccb, NULL, 0, 0); 1232 } 1233 break; 1234 } 1235 case XPT_EN_LUN: /* Enable LUN as a target */ 1236 case XPT_TARGET_IO: /* Execute target I/O request */ 1237 case XPT_ACCEPT_TARGET_IO: /* Accept Host Target Mode CDB */ 1238 case XPT_CONT_TARGET_IO: /* Continue Host Target I/O Connection*/ 1239 case XPT_ABORT: /* Abort the specified CCB */ 1240 /* XXX Implement */ 1241 ccb->ccb_h.status = CAM_REQ_INVALID; 1242 xpt_done(ccb); 1243 break; 1244 case XPT_SET_TRAN_SETTINGS: 1245 { 1246 /* XXX Implement */ 1247 ccb->ccb_h.status = CAM_PROVIDE_FAIL; 1248 xpt_done(ccb); 1249 break; 1250 } 1251 case XPT_GET_TRAN_SETTINGS: 1252 /* Get default/user set transfer settings for the target */ 1253 { 1254 struct ccb_trans_settings *cts; 1255 u_int target_mask; 1256 1257 cts = &ccb->cts; 1258 target_mask = 0x01 << ccb->ccb_h.target_id; 1259 if ((cts->flags & CCB_TRANS_USER_SETTINGS) != 0) { 1260 cts->flags = 0; 1261 if ((bt->disc_permitted & target_mask) != 0) 1262 cts->flags |= CCB_TRANS_DISC_ENB; 1263 if ((bt->tags_permitted & target_mask) != 0) 1264 cts->flags |= CCB_TRANS_TAG_ENB; 1265 if ((bt->wide_permitted & target_mask) != 0) 1266 cts->bus_width = MSG_EXT_WDTR_BUS_16_BIT; 1267 else 1268 cts->bus_width = MSG_EXT_WDTR_BUS_8_BIT; 1269 if ((bt->ultra_permitted & target_mask) != 0) 1270 cts->sync_period = 12; 1271 else if ((bt->fast_permitted & target_mask) != 0) 1272 cts->sync_period = 25; 1273 else if ((bt->sync_permitted & target_mask) != 0) 1274 cts->sync_period = 50; 1275 else 1276 cts->sync_period = 0; 1277 1278 if (cts->sync_period != 0) 1279 cts->sync_offset = 15; 1280 1281 cts->valid = CCB_TRANS_SYNC_RATE_VALID 1282 | CCB_TRANS_SYNC_OFFSET_VALID 1283 | CCB_TRANS_BUS_WIDTH_VALID 1284 | CCB_TRANS_DISC_VALID 1285 | CCB_TRANS_TQ_VALID; 1286 } else { 1287 btfetchtransinfo(bt, cts); 1288 } 1289 1290 ccb->ccb_h.status = CAM_REQ_CMP; 1291 xpt_done(ccb); 1292 break; 1293 } 1294 case XPT_CALC_GEOMETRY: 1295 { 1296 struct ccb_calc_geometry *ccg; 1297 u_int32_t size_mb; 1298 u_int32_t secs_per_cylinder; 1299 1300 ccg = &ccb->ccg; 1301 size_mb = ccg->volume_size 1302 / ((1024L * 1024L) / ccg->block_size); 1303 1304 if (size_mb >= 1024 && (bt->extended_trans != 0)) { 1305 if (size_mb >= 2048) { 1306 ccg->heads = 255; 1307 ccg->secs_per_track = 63; 1308 } else { 1309 ccg->heads = 128; 1310 ccg->secs_per_track = 32; 1311 } 1312 } else { 1313 ccg->heads = 64; 1314 ccg->secs_per_track = 32; 1315 } 1316 secs_per_cylinder = ccg->heads * ccg->secs_per_track; 1317 ccg->cylinders = ccg->volume_size / secs_per_cylinder; 1318 ccb->ccb_h.status = CAM_REQ_CMP; 1319 xpt_done(ccb); 1320 break; 1321 } 1322 case XPT_RESET_BUS: /* Reset the specified SCSI bus */ 1323 { 1324 btreset(bt, /*hardreset*/TRUE); 1325 ccb->ccb_h.status = CAM_REQ_CMP; 1326 xpt_done(ccb); 1327 break; 1328 } 1329 case XPT_TERM_IO: /* Terminate the I/O process */ 1330 /* XXX Implement */ 1331 ccb->ccb_h.status = CAM_REQ_INVALID; 1332 xpt_done(ccb); 1333 break; 1334 case XPT_PATH_INQ: /* Path routing inquiry */ 1335 { 1336 struct ccb_pathinq *cpi = &ccb->cpi; 1337 1338 cpi->version_num = 1; /* XXX??? */ 1339 cpi->hba_inquiry = PI_SDTR_ABLE; 1340 if (bt->tag_capable != 0) 1341 cpi->hba_inquiry |= PI_TAG_ABLE; 1342 if (bt->wide_bus != 0) 1343 cpi->hba_inquiry |= PI_WIDE_16; 1344 cpi->target_sprt = 0; 1345 cpi->hba_misc = 0; 1346 cpi->hba_eng_cnt = 0; 1347 cpi->max_target = bt->wide_bus ? 15 : 7; 1348 cpi->max_lun = 7; 1349 cpi->initiator_id = bt->scsi_id; 1350 cpi->bus_id = cam_sim_bus(sim); 1351 cpi->base_transfer_speed = 3300; 1352 strncpy(cpi->sim_vid, "FreeBSD", SIM_IDLEN); 1353 strncpy(cpi->hba_vid, "BusLogic", HBA_IDLEN); 1354 strncpy(cpi->dev_name, cam_sim_name(sim), DEV_IDLEN); 1355 cpi->unit_number = cam_sim_unit(sim); 1356 cpi->ccb_h.status = CAM_REQ_CMP; 1357 xpt_done(ccb); 1358 break; 1359 } 1360 default: 1361 ccb->ccb_h.status = CAM_REQ_INVALID; 1362 xpt_done(ccb); 1363 break; 1364 } 1365 } 1366 1367 static void 1368 btexecuteccb(void *arg, bus_dma_segment_t *dm_segs, int nseg, int error) 1369 { 1370 struct bt_ccb *bccb; 1371 union ccb *ccb; 1372 struct bt_softc *bt; 1373 int s; 1374 1375 bccb = (struct bt_ccb *)arg; 1376 ccb = bccb->ccb; 1377 bt = (struct bt_softc *)ccb->ccb_h.ccb_bt_ptr; 1378 1379 if (error != 0) { 1380 if (error != EFBIG) 1381 device_printf(bt->dev, 1382 "Unexepected error 0x%x returned from " 1383 "bus_dmamap_load\n", error); 1384 if (ccb->ccb_h.status == CAM_REQ_INPROG) { 1385 xpt_freeze_devq(ccb->ccb_h.path, /*count*/1); 1386 ccb->ccb_h.status = CAM_REQ_TOO_BIG|CAM_DEV_QFRZN; 1387 } 1388 btfreeccb(bt, bccb); 1389 xpt_done(ccb); 1390 return; 1391 } 1392 1393 if (nseg != 0) { 1394 bt_sg_t *sg; 1395 bus_dma_segment_t *end_seg; 1396 bus_dmasync_op_t op; 1397 1398 end_seg = dm_segs + nseg; 1399 1400 /* Copy the segments into our SG list */ 1401 sg = bccb->sg_list; 1402 while (dm_segs < end_seg) { 1403 sg->len = dm_segs->ds_len; 1404 sg->addr = dm_segs->ds_addr; 1405 sg++; 1406 dm_segs++; 1407 } 1408 1409 if (nseg > 1) { 1410 bccb->hccb.opcode = INITIATOR_SG_CCB_WRESID; 1411 bccb->hccb.data_len = sizeof(bt_sg_t) * nseg; 1412 bccb->hccb.data_addr = bccb->sg_list_phys; 1413 } else { 1414 bccb->hccb.data_len = bccb->sg_list->len; 1415 bccb->hccb.data_addr = bccb->sg_list->addr; 1416 } 1417 1418 if ((ccb->ccb_h.flags & CAM_DIR_MASK) == CAM_DIR_IN) 1419 op = BUS_DMASYNC_PREREAD; 1420 else 1421 op = BUS_DMASYNC_PREWRITE; 1422 1423 bus_dmamap_sync(bt->buffer_dmat, bccb->dmamap, op); 1424 1425 } else { 1426 bccb->hccb.opcode = INITIATOR_CCB; 1427 bccb->hccb.data_len = 0; 1428 bccb->hccb.data_addr = 0; 1429 } 1430 1431 s = splcam(); 1432 1433 /* 1434 * Last time we need to check if this CCB needs to 1435 * be aborted. 1436 */ 1437 if (ccb->ccb_h.status != CAM_REQ_INPROG) { 1438 if (nseg != 0) 1439 bus_dmamap_unload(bt->buffer_dmat, bccb->dmamap); 1440 btfreeccb(bt, bccb); 1441 xpt_done(ccb); 1442 splx(s); 1443 return; 1444 } 1445 1446 bccb->flags = BCCB_ACTIVE; 1447 ccb->ccb_h.status |= CAM_SIM_QUEUED; 1448 LIST_INSERT_HEAD(&bt->pending_ccbs, &ccb->ccb_h, sim_links.le); 1449 1450 ccb->ccb_h.timeout_ch = 1451 timeout(bttimeout, (caddr_t)bccb, 1452 (ccb->ccb_h.timeout * hz) / 1000); 1453 1454 /* Tell the adapter about this command */ 1455 bt->cur_outbox->ccb_addr = btccbvtop(bt, bccb); 1456 if (bt->cur_outbox->action_code != BMBO_FREE) { 1457 /* 1458 * We should never encounter a busy mailbox. 1459 * If we do, warn the user, and treat it as 1460 * a resource shortage. If the controller is 1461 * hung, one of the pending transactions will 1462 * timeout causing us to start recovery operations. 1463 */ 1464 device_printf(bt->dev, 1465 "Encountered busy mailbox with %d out of %d " 1466 "commands active!!!\n", bt->active_ccbs, 1467 bt->max_ccbs); 1468 untimeout(bttimeout, bccb, ccb->ccb_h.timeout_ch); 1469 if (nseg != 0) 1470 bus_dmamap_unload(bt->buffer_dmat, bccb->dmamap); 1471 btfreeccb(bt, bccb); 1472 bt->resource_shortage = TRUE; 1473 xpt_freeze_simq(bt->sim, /*count*/1); 1474 ccb->ccb_h.status = CAM_REQUEUE_REQ; 1475 xpt_done(ccb); 1476 return; 1477 } 1478 bt->cur_outbox->action_code = BMBO_START; 1479 bt_outb(bt, COMMAND_REG, BOP_START_MBOX); 1480 btnextoutbox(bt); 1481 splx(s); 1482 } 1483 1484 void 1485 bt_intr(void *arg) 1486 { 1487 struct bt_softc *bt; 1488 u_int intstat; 1489 1490 bt = (struct bt_softc *)arg; 1491 while (((intstat = bt_inb(bt, INTSTAT_REG)) & INTR_PENDING) != 0) { 1492 1493 if ((intstat & CMD_COMPLETE) != 0) { 1494 bt->latched_status = bt_inb(bt, STATUS_REG); 1495 bt->command_cmp = TRUE; 1496 } 1497 1498 bt_outb(bt, CONTROL_REG, RESET_INTR); 1499 1500 if ((intstat & IMB_LOADED) != 0) { 1501 while (bt->cur_inbox->comp_code != BMBI_FREE) { 1502 btdone(bt, 1503 btccbptov(bt, bt->cur_inbox->ccb_addr), 1504 bt->cur_inbox->comp_code); 1505 bt->cur_inbox->comp_code = BMBI_FREE; 1506 btnextinbox(bt); 1507 } 1508 } 1509 1510 if ((intstat & SCSI_BUS_RESET) != 0) { 1511 btreset(bt, /*hardreset*/FALSE); 1512 } 1513 } 1514 } 1515 1516 static void 1517 btdone(struct bt_softc *bt, struct bt_ccb *bccb, bt_mbi_comp_code_t comp_code) 1518 { 1519 union ccb *ccb; 1520 struct ccb_scsiio *csio; 1521 1522 ccb = bccb->ccb; 1523 csio = &bccb->ccb->csio; 1524 1525 if ((bccb->flags & BCCB_ACTIVE) == 0) { 1526 device_printf(bt->dev, 1527 "btdone - Attempt to free non-active BCCB %p\n", 1528 (void *)bccb); 1529 return; 1530 } 1531 1532 if ((ccb->ccb_h.flags & CAM_DIR_MASK) != CAM_DIR_NONE) { 1533 bus_dmasync_op_t op; 1534 1535 if ((ccb->ccb_h.flags & CAM_DIR_MASK) == CAM_DIR_IN) 1536 op = BUS_DMASYNC_POSTREAD; 1537 else 1538 op = BUS_DMASYNC_POSTWRITE; 1539 bus_dmamap_sync(bt->buffer_dmat, bccb->dmamap, op); 1540 bus_dmamap_unload(bt->buffer_dmat, bccb->dmamap); 1541 } 1542 1543 if (bccb == bt->recovery_bccb) { 1544 /* 1545 * The recovery BCCB does not have a CCB associated 1546 * with it, so short circuit the normal error handling. 1547 * We now traverse our list of pending CCBs and process 1548 * any that were terminated by the recovery CCBs action. 1549 * We also reinstate timeouts for all remaining, pending, 1550 * CCBs. 1551 */ 1552 struct cam_path *path; 1553 struct ccb_hdr *ccb_h; 1554 cam_status error; 1555 1556 /* Notify all clients that a BDR occured */ 1557 error = xpt_create_path(&path, /*periph*/NULL, 1558 cam_sim_path(bt->sim), 1559 bccb->hccb.target_id, 1560 CAM_LUN_WILDCARD); 1561 1562 if (error == CAM_REQ_CMP) 1563 xpt_async(AC_SENT_BDR, path, NULL); 1564 1565 ccb_h = LIST_FIRST(&bt->pending_ccbs); 1566 while (ccb_h != NULL) { 1567 struct bt_ccb *pending_bccb; 1568 1569 pending_bccb = (struct bt_ccb *)ccb_h->ccb_bccb_ptr; 1570 if (pending_bccb->hccb.target_id 1571 == bccb->hccb.target_id) { 1572 pending_bccb->hccb.btstat = BTSTAT_HA_BDR; 1573 ccb_h = LIST_NEXT(ccb_h, sim_links.le); 1574 btdone(bt, pending_bccb, BMBI_ERROR); 1575 } else { 1576 ccb_h->timeout_ch = 1577 timeout(bttimeout, (caddr_t)pending_bccb, 1578 (ccb_h->timeout * hz) / 1000); 1579 ccb_h = LIST_NEXT(ccb_h, sim_links.le); 1580 } 1581 } 1582 device_printf(bt->dev, "No longer in timeout\n"); 1583 return; 1584 } 1585 1586 untimeout(bttimeout, bccb, ccb->ccb_h.timeout_ch); 1587 1588 switch (comp_code) { 1589 case BMBI_FREE: 1590 device_printf(bt->dev, 1591 "btdone - CCB completed with free status!\n"); 1592 break; 1593 case BMBI_NOT_FOUND: 1594 device_printf(bt->dev, 1595 "btdone - CCB Abort failed to find CCB\n"); 1596 break; 1597 case BMBI_ABORT: 1598 case BMBI_ERROR: 1599 if (bootverbose) { 1600 printf("bt: ccb %p - error %x occured. " 1601 "btstat = %x, sdstat = %x\n", 1602 (void *)bccb, comp_code, bccb->hccb.btstat, 1603 bccb->hccb.sdstat); 1604 } 1605 /* An error occured */ 1606 switch(bccb->hccb.btstat) { 1607 case BTSTAT_DATARUN_ERROR: 1608 if (bccb->hccb.data_len == 0) { 1609 /* 1610 * At least firmware 4.22, does this 1611 * for a QUEUE FULL condition. 1612 */ 1613 bccb->hccb.sdstat = SCSI_STATUS_QUEUE_FULL; 1614 } else if (bccb->hccb.data_len < 0) { 1615 csio->ccb_h.status = CAM_DATA_RUN_ERR; 1616 break; 1617 } 1618 /* FALLTHROUGH */ 1619 case BTSTAT_NOERROR: 1620 case BTSTAT_LINKED_CMD_COMPLETE: 1621 case BTSTAT_LINKED_CMD_FLAG_COMPLETE: 1622 case BTSTAT_DATAUNDERUN_ERROR: 1623 1624 csio->scsi_status = bccb->hccb.sdstat; 1625 csio->ccb_h.status |= CAM_SCSI_STATUS_ERROR; 1626 switch(csio->scsi_status) { 1627 case SCSI_STATUS_CHECK_COND: 1628 case SCSI_STATUS_CMD_TERMINATED: 1629 csio->ccb_h.status |= CAM_AUTOSNS_VALID; 1630 /* Bounce sense back if necessary */ 1631 if (bt->sense_buffers != NULL) { 1632 csio->sense_data = 1633 *btsensevaddr(bt, bccb); 1634 } 1635 break; 1636 default: 1637 break; 1638 case SCSI_STATUS_OK: 1639 csio->ccb_h.status = CAM_REQ_CMP; 1640 break; 1641 } 1642 csio->resid = bccb->hccb.data_len; 1643 break; 1644 case BTSTAT_SELTIMEOUT: 1645 csio->ccb_h.status = CAM_SEL_TIMEOUT; 1646 break; 1647 case BTSTAT_UNEXPECTED_BUSFREE: 1648 csio->ccb_h.status = CAM_UNEXP_BUSFREE; 1649 break; 1650 case BTSTAT_INVALID_PHASE: 1651 csio->ccb_h.status = CAM_SEQUENCE_FAIL; 1652 break; 1653 case BTSTAT_INVALID_ACTION_CODE: 1654 panic("%s: Inavlid Action code", bt_name(bt)); 1655 break; 1656 case BTSTAT_INVALID_OPCODE: 1657 panic("%s: Inavlid CCB Opcode code", bt_name(bt)); 1658 break; 1659 case BTSTAT_LINKED_CCB_LUN_MISMATCH: 1660 /* We don't even support linked commands... */ 1661 panic("%s: Linked CCB Lun Mismatch", bt_name(bt)); 1662 break; 1663 case BTSTAT_INVALID_CCB_OR_SG_PARAM: 1664 panic("%s: Invalid CCB or SG list", bt_name(bt)); 1665 break; 1666 case BTSTAT_AUTOSENSE_FAILED: 1667 csio->ccb_h.status = CAM_AUTOSENSE_FAIL; 1668 break; 1669 case BTSTAT_TAGGED_MSG_REJECTED: 1670 { 1671 struct ccb_trans_settings neg; 1672 1673 xpt_print_path(csio->ccb_h.path); 1674 printf("refuses tagged commands. Performing " 1675 "non-tagged I/O\n"); 1676 neg.flags = 0; 1677 neg.valid = CCB_TRANS_TQ_VALID; 1678 xpt_setup_ccb(&neg.ccb_h, csio->ccb_h.path, 1679 /*priority*/1); 1680 xpt_async(AC_TRANSFER_NEG, csio->ccb_h.path, &neg); 1681 bt->tags_permitted &= ~(0x01 << csio->ccb_h.target_id); 1682 csio->ccb_h.status = CAM_MSG_REJECT_REC; 1683 break; 1684 } 1685 case BTSTAT_UNSUPPORTED_MSG_RECEIVED: 1686 /* 1687 * XXX You would think that this is 1688 * a recoverable error... Hmmm. 1689 */ 1690 csio->ccb_h.status = CAM_REQ_CMP_ERR; 1691 break; 1692 case BTSTAT_HA_SOFTWARE_ERROR: 1693 case BTSTAT_HA_WATCHDOG_ERROR: 1694 case BTSTAT_HARDWARE_FAILURE: 1695 /* Hardware reset ??? Can we recover ??? */ 1696 csio->ccb_h.status = CAM_NO_HBA; 1697 break; 1698 case BTSTAT_TARGET_IGNORED_ATN: 1699 case BTSTAT_OTHER_SCSI_BUS_RESET: 1700 case BTSTAT_HA_SCSI_BUS_RESET: 1701 if ((csio->ccb_h.status & CAM_STATUS_MASK) 1702 != CAM_CMD_TIMEOUT) 1703 csio->ccb_h.status = CAM_SCSI_BUS_RESET; 1704 break; 1705 case BTSTAT_HA_BDR: 1706 if ((bccb->flags & BCCB_DEVICE_RESET) == 0) 1707 csio->ccb_h.status = CAM_BDR_SENT; 1708 else 1709 csio->ccb_h.status = CAM_CMD_TIMEOUT; 1710 break; 1711 case BTSTAT_INVALID_RECONNECT: 1712 case BTSTAT_ABORT_QUEUE_GENERATED: 1713 csio->ccb_h.status = CAM_REQ_TERMIO; 1714 break; 1715 case BTSTAT_SCSI_PERROR_DETECTED: 1716 csio->ccb_h.status = CAM_UNCOR_PARITY; 1717 break; 1718 } 1719 if (csio->ccb_h.status != CAM_REQ_CMP) { 1720 xpt_freeze_devq(csio->ccb_h.path, /*count*/1); 1721 csio->ccb_h.status |= CAM_DEV_QFRZN; 1722 } 1723 if ((bccb->flags & BCCB_RELEASE_SIMQ) != 0) 1724 ccb->ccb_h.status |= CAM_RELEASE_SIMQ; 1725 btfreeccb(bt, bccb); 1726 xpt_done(ccb); 1727 break; 1728 case BMBI_OK: 1729 /* All completed without incident */ 1730 ccb->ccb_h.status |= CAM_REQ_CMP; 1731 if ((bccb->flags & BCCB_RELEASE_SIMQ) != 0) 1732 ccb->ccb_h.status |= CAM_RELEASE_SIMQ; 1733 btfreeccb(bt, bccb); 1734 xpt_done(ccb); 1735 break; 1736 } 1737 } 1738 1739 static int 1740 btreset(struct bt_softc* bt, int hard_reset) 1741 { 1742 struct ccb_hdr *ccb_h; 1743 u_int status; 1744 u_int timeout; 1745 u_int8_t reset_type; 1746 1747 if (hard_reset != 0) 1748 reset_type = HARD_RESET; 1749 else 1750 reset_type = SOFT_RESET; 1751 bt_outb(bt, CONTROL_REG, reset_type); 1752 1753 /* Wait 5sec. for Diagnostic start */ 1754 timeout = 5 * 10000; 1755 while (--timeout) { 1756 status = bt_inb(bt, STATUS_REG); 1757 if ((status & DIAG_ACTIVE) != 0) 1758 break; 1759 DELAY(100); 1760 } 1761 if (timeout == 0) { 1762 if (bootverbose) 1763 printf("%s: btreset - Diagnostic Active failed to " 1764 "assert. status = 0x%x\n", bt_name(bt), status); 1765 return (ETIMEDOUT); 1766 } 1767 1768 /* Wait 10sec. for Diagnostic end */ 1769 timeout = 10 * 10000; 1770 while (--timeout) { 1771 status = bt_inb(bt, STATUS_REG); 1772 if ((status & DIAG_ACTIVE) == 0) 1773 break; 1774 DELAY(100); 1775 } 1776 if (timeout == 0) { 1777 panic("%s: btreset - Diagnostic Active failed to drop. " 1778 "status = 0x%x\n", bt_name(bt), status); 1779 return (ETIMEDOUT); 1780 } 1781 1782 /* Wait for the host adapter to become ready or report a failure */ 1783 timeout = 10000; 1784 while (--timeout) { 1785 status = bt_inb(bt, STATUS_REG); 1786 if ((status & (DIAG_FAIL|HA_READY|DATAIN_REG_READY)) != 0) 1787 break; 1788 DELAY(100); 1789 } 1790 if (timeout == 0) { 1791 printf("%s: btreset - Host adapter failed to come ready. " 1792 "status = 0x%x\n", bt_name(bt), status); 1793 return (ETIMEDOUT); 1794 } 1795 1796 /* If the diagnostics failed, tell the user */ 1797 if ((status & DIAG_FAIL) != 0 1798 || (status & HA_READY) == 0) { 1799 printf("%s: btreset - Adapter failed diagnostics\n", 1800 bt_name(bt)); 1801 1802 if ((status & DATAIN_REG_READY) != 0) 1803 printf("%s: btreset - Host Adapter Error code = 0x%x\n", 1804 bt_name(bt), bt_inb(bt, DATAIN_REG)); 1805 return (ENXIO); 1806 } 1807 1808 /* If we've allocated mailboxes, initialize them */ 1809 if (bt->init_level > 4) 1810 btinitmboxes(bt); 1811 1812 /* If we've attached to the XPT, tell it about the event */ 1813 if (bt->path != NULL) 1814 xpt_async(AC_BUS_RESET, bt->path, NULL); 1815 1816 /* 1817 * Perform completion processing for all outstanding CCBs. 1818 */ 1819 while ((ccb_h = LIST_FIRST(&bt->pending_ccbs)) != NULL) { 1820 struct bt_ccb *pending_bccb; 1821 1822 pending_bccb = (struct bt_ccb *)ccb_h->ccb_bccb_ptr; 1823 pending_bccb->hccb.btstat = BTSTAT_HA_SCSI_BUS_RESET; 1824 btdone(bt, pending_bccb, BMBI_ERROR); 1825 } 1826 1827 return (0); 1828 } 1829 1830 /* 1831 * Send a command to the adapter. 1832 */ 1833 int 1834 bt_cmd(struct bt_softc *bt, bt_op_t opcode, u_int8_t *params, u_int param_len, 1835 u_int8_t *reply_data, u_int reply_len, u_int cmd_timeout) 1836 { 1837 u_int timeout; 1838 u_int status; 1839 u_int saved_status; 1840 u_int intstat; 1841 u_int reply_buf_size; 1842 int s; 1843 int cmd_complete; 1844 int error; 1845 1846 /* No data returned to start */ 1847 reply_buf_size = reply_len; 1848 reply_len = 0; 1849 intstat = 0; 1850 cmd_complete = 0; 1851 saved_status = 0; 1852 error = 0; 1853 1854 bt->command_cmp = 0; 1855 /* 1856 * Wait up to 10 sec. for the adapter to become 1857 * ready to accept commands. 1858 */ 1859 timeout = 100000; 1860 while (--timeout) { 1861 status = bt_inb(bt, STATUS_REG); 1862 if ((status & HA_READY) != 0 1863 && (status & CMD_REG_BUSY) == 0) 1864 break; 1865 /* 1866 * Throw away any pending data which may be 1867 * left over from earlier commands that we 1868 * timedout on. 1869 */ 1870 if ((status & DATAIN_REG_READY) != 0) 1871 (void)bt_inb(bt, DATAIN_REG); 1872 DELAY(100); 1873 } 1874 if (timeout == 0) { 1875 printf("%s: bt_cmd: Timeout waiting for adapter ready, " 1876 "status = 0x%x\n", bt_name(bt), status); 1877 return (ETIMEDOUT); 1878 } 1879 1880 /* 1881 * Send the opcode followed by any necessary parameter bytes. 1882 */ 1883 bt_outb(bt, COMMAND_REG, opcode); 1884 1885 /* 1886 * Wait for up to 1sec for each byte of the the 1887 * parameter list sent to be sent. 1888 */ 1889 timeout = 10000; 1890 while (param_len && --timeout) { 1891 DELAY(100); 1892 s = splcam(); 1893 status = bt_inb(bt, STATUS_REG); 1894 intstat = bt_inb(bt, INTSTAT_REG); 1895 splx(s); 1896 1897 if ((intstat & (INTR_PENDING|CMD_COMPLETE)) 1898 == (INTR_PENDING|CMD_COMPLETE)) { 1899 saved_status = status; 1900 cmd_complete = 1; 1901 break; 1902 } 1903 if (bt->command_cmp != 0) { 1904 saved_status = bt->latched_status; 1905 cmd_complete = 1; 1906 break; 1907 } 1908 if ((status & DATAIN_REG_READY) != 0) 1909 break; 1910 if ((status & CMD_REG_BUSY) == 0) { 1911 bt_outb(bt, COMMAND_REG, *params++); 1912 param_len--; 1913 timeout = 10000; 1914 } 1915 } 1916 if (timeout == 0) { 1917 printf("%s: bt_cmd: Timeout sending parameters, " 1918 "status = 0x%x\n", bt_name(bt), status); 1919 cmd_complete = 1; 1920 saved_status = status; 1921 error = ETIMEDOUT; 1922 } 1923 1924 /* 1925 * Wait for the command to complete. 1926 */ 1927 while (cmd_complete == 0 && --cmd_timeout) { 1928 1929 s = splcam(); 1930 status = bt_inb(bt, STATUS_REG); 1931 intstat = bt_inb(bt, INTSTAT_REG); 1932 /* 1933 * It may be that this command was issued with 1934 * controller interrupts disabled. We'll never 1935 * get to our command if an incoming mailbox 1936 * interrupt is pending, so take care of completed 1937 * mailbox commands by calling our interrupt handler. 1938 */ 1939 if ((intstat & (INTR_PENDING|IMB_LOADED)) 1940 == (INTR_PENDING|IMB_LOADED)) 1941 bt_intr(bt); 1942 splx(s); 1943 1944 if (bt->command_cmp != 0) { 1945 /* 1946 * Our interrupt handler saw CMD_COMPLETE 1947 * status before we did. 1948 */ 1949 cmd_complete = 1; 1950 saved_status = bt->latched_status; 1951 } else if ((intstat & (INTR_PENDING|CMD_COMPLETE)) 1952 == (INTR_PENDING|CMD_COMPLETE)) { 1953 /* 1954 * Our poll (in case interrupts are blocked) 1955 * saw the CMD_COMPLETE interrupt. 1956 */ 1957 cmd_complete = 1; 1958 saved_status = status; 1959 } else if (opcode == BOP_MODIFY_IO_ADDR 1960 && (status & CMD_REG_BUSY) == 0) { 1961 /* 1962 * The BOP_MODIFY_IO_ADDR does not issue a CMD_COMPLETE, 1963 * but it should update the status register. So, we 1964 * consider this command complete when the CMD_REG_BUSY 1965 * status clears. 1966 */ 1967 saved_status = status; 1968 cmd_complete = 1; 1969 } else if ((status & DATAIN_REG_READY) != 0) { 1970 u_int8_t data; 1971 1972 data = bt_inb(bt, DATAIN_REG); 1973 if (reply_len < reply_buf_size) { 1974 *reply_data++ = data; 1975 } else { 1976 printf("%s: bt_cmd - Discarded reply data byte " 1977 "for opcode 0x%x\n", bt_name(bt), 1978 opcode); 1979 } 1980 /* 1981 * Reset timeout to ensure at least a second 1982 * between response bytes. 1983 */ 1984 cmd_timeout = MAX(cmd_timeout, 10000); 1985 reply_len++; 1986 1987 } else if ((opcode == BOP_FETCH_LRAM) 1988 && (status & HA_READY) != 0) { 1989 saved_status = status; 1990 cmd_complete = 1; 1991 } 1992 DELAY(100); 1993 } 1994 if (cmd_timeout == 0) { 1995 printf("%s: bt_cmd: Timeout waiting for command (%x) " 1996 "to complete.\n%s: status = 0x%x, intstat = 0x%x, " 1997 "rlen %d\n", bt_name(bt), opcode, 1998 bt_name(bt), status, intstat, reply_len); 1999 error = (ETIMEDOUT); 2000 } 2001 2002 /* 2003 * Clear any pending interrupts. Block interrupts so our 2004 * interrupt handler is not re-entered. 2005 */ 2006 s = splcam(); 2007 bt_intr(bt); 2008 splx(s); 2009 2010 if (error != 0) 2011 return (error); 2012 2013 /* 2014 * If the command was rejected by the controller, tell the caller. 2015 */ 2016 if ((saved_status & CMD_INVALID) != 0) { 2017 /* 2018 * Some early adapters may not recover properly from 2019 * an invalid command. If it appears that the controller 2020 * has wedged (i.e. status was not cleared by our interrupt 2021 * reset above), perform a soft reset. 2022 */ 2023 if (bootverbose) 2024 printf("%s: Invalid Command 0x%x\n", bt_name(bt), 2025 opcode); 2026 DELAY(1000); 2027 status = bt_inb(bt, STATUS_REG); 2028 if ((status & (CMD_INVALID|STATUS_REG_RSVD|DATAIN_REG_READY| 2029 CMD_REG_BUSY|DIAG_FAIL|DIAG_ACTIVE)) != 0 2030 || (status & (HA_READY|INIT_REQUIRED)) 2031 != (HA_READY|INIT_REQUIRED)) { 2032 btreset(bt, /*hard_reset*/FALSE); 2033 } 2034 return (EINVAL); 2035 } 2036 2037 if (param_len > 0) { 2038 /* The controller did not accept the full argument list */ 2039 return (E2BIG); 2040 } 2041 2042 if (reply_len != reply_buf_size) { 2043 /* Too much or too little data received */ 2044 return (EMSGSIZE); 2045 } 2046 2047 /* We were successful */ 2048 return (0); 2049 } 2050 2051 static int 2052 btinitmboxes(struct bt_softc *bt) { 2053 init_32b_mbox_params_t init_mbox; 2054 int error; 2055 2056 bzero(bt->in_boxes, sizeof(bt_mbox_in_t) * bt->num_boxes); 2057 bzero(bt->out_boxes, sizeof(bt_mbox_out_t) * bt->num_boxes); 2058 bt->cur_inbox = bt->in_boxes; 2059 bt->last_inbox = bt->in_boxes + bt->num_boxes - 1; 2060 bt->cur_outbox = bt->out_boxes; 2061 bt->last_outbox = bt->out_boxes + bt->num_boxes - 1; 2062 2063 /* Tell the adapter about them */ 2064 init_mbox.num_boxes = bt->num_boxes; 2065 init_mbox.base_addr[0] = bt->mailbox_physbase & 0xFF; 2066 init_mbox.base_addr[1] = (bt->mailbox_physbase >> 8) & 0xFF; 2067 init_mbox.base_addr[2] = (bt->mailbox_physbase >> 16) & 0xFF; 2068 init_mbox.base_addr[3] = (bt->mailbox_physbase >> 24) & 0xFF; 2069 error = bt_cmd(bt, BOP_INITIALIZE_32BMBOX, (u_int8_t *)&init_mbox, 2070 /*parmlen*/sizeof(init_mbox), /*reply_buf*/NULL, 2071 /*reply_len*/0, DEFAULT_CMD_TIMEOUT); 2072 2073 if (error != 0) 2074 printf("btinitmboxes: Initialization command failed\n"); 2075 else if (bt->strict_rr != 0) { 2076 /* 2077 * If the controller supports 2078 * strict round robin mode, 2079 * enable it 2080 */ 2081 u_int8_t param; 2082 2083 param = 0; 2084 error = bt_cmd(bt, BOP_ENABLE_STRICT_RR, ¶m, 1, 2085 /*reply_buf*/NULL, /*reply_len*/0, 2086 DEFAULT_CMD_TIMEOUT); 2087 2088 if (error != 0) { 2089 printf("btinitmboxes: Unable to enable strict RR\n"); 2090 error = 0; 2091 } else if (bootverbose) { 2092 printf("%s: Using Strict Round Robin Mailbox Mode\n", 2093 bt_name(bt)); 2094 } 2095 } 2096 2097 return (error); 2098 } 2099 2100 /* 2101 * Update the XPT's idea of the negotiated transfer 2102 * parameters for a particular target. 2103 */ 2104 static void 2105 btfetchtransinfo(struct bt_softc *bt, struct ccb_trans_settings* cts) 2106 { 2107 setup_data_t setup_info; 2108 u_int target; 2109 u_int targ_offset; 2110 u_int targ_mask; 2111 u_int sync_period; 2112 int error; 2113 u_int8_t param; 2114 targ_syncinfo_t sync_info; 2115 2116 target = cts->ccb_h.target_id; 2117 targ_offset = (target & 0x7); 2118 targ_mask = (0x01 << targ_offset); 2119 2120 /* 2121 * Inquire Setup Information. This command retreives the 2122 * Wide negotiation status for recent adapters as well as 2123 * the sync info for older models. 2124 */ 2125 param = sizeof(setup_info); 2126 error = bt_cmd(bt, BOP_INQUIRE_SETUP_INFO, ¶m, /*paramlen*/1, 2127 (u_int8_t*)&setup_info, sizeof(setup_info), 2128 DEFAULT_CMD_TIMEOUT); 2129 2130 if (error != 0) { 2131 printf("%s: btfetchtransinfo - Inquire Setup Info Failed %x\n", 2132 bt_name(bt), error); 2133 cts->valid = 0; 2134 return; 2135 } 2136 2137 sync_info = (target < 8) ? setup_info.low_syncinfo[targ_offset] 2138 : setup_info.high_syncinfo[targ_offset]; 2139 2140 if (sync_info.sync == 0) 2141 cts->sync_offset = 0; 2142 else 2143 cts->sync_offset = sync_info.offset; 2144 2145 cts->bus_width = MSG_EXT_WDTR_BUS_8_BIT; 2146 if (strcmp(bt->firmware_ver, "5.06L") >= 0) { 2147 u_int wide_active; 2148 2149 wide_active = 2150 (target < 8) ? (setup_info.low_wide_active & targ_mask) 2151 : (setup_info.high_wide_active & targ_mask); 2152 2153 if (wide_active) 2154 cts->bus_width = MSG_EXT_WDTR_BUS_16_BIT; 2155 } else if ((bt->wide_permitted & targ_mask) != 0) { 2156 struct ccb_getdev cgd; 2157 2158 /* 2159 * Prior to rev 5.06L, wide status isn't provided, 2160 * so we "guess" that wide transfers are in effect 2161 * if the user settings allow for wide and the inquiry 2162 * data for the device indicates that it can handle 2163 * wide transfers. 2164 */ 2165 xpt_setup_ccb(&cgd.ccb_h, cts->ccb_h.path, /*priority*/1); 2166 cgd.ccb_h.func_code = XPT_GDEV_TYPE; 2167 xpt_action((union ccb *)&cgd); 2168 if ((cgd.ccb_h.status & CAM_STATUS_MASK) == CAM_REQ_CMP 2169 && (cgd.inq_data.flags & SID_WBus16) != 0) 2170 cts->bus_width = MSG_EXT_WDTR_BUS_16_BIT; 2171 } 2172 2173 if (bt->firmware_ver[0] >= '3') { 2174 /* 2175 * For adapters that can do fast or ultra speeds, 2176 * use the more exact Target Sync Information command. 2177 */ 2178 target_sync_info_data_t sync_info; 2179 2180 param = sizeof(sync_info); 2181 error = bt_cmd(bt, BOP_TARG_SYNC_INFO, ¶m, /*paramlen*/1, 2182 (u_int8_t*)&sync_info, sizeof(sync_info), 2183 DEFAULT_CMD_TIMEOUT); 2184 2185 if (error != 0) { 2186 printf("%s: btfetchtransinfo - Inquire Sync " 2187 "Info Failed 0x%x\n", bt_name(bt), error); 2188 cts->valid = 0; 2189 return; 2190 } 2191 sync_period = sync_info.sync_rate[target] * 100; 2192 } else { 2193 sync_period = 2000 + (500 * sync_info.period); 2194 } 2195 2196 /* Convert ns value to standard SCSI sync rate */ 2197 if (cts->sync_offset != 0) 2198 cts->sync_period = scsi_calc_syncparam(sync_period); 2199 else 2200 cts->sync_period = 0; 2201 2202 cts->valid = CCB_TRANS_SYNC_RATE_VALID 2203 | CCB_TRANS_SYNC_OFFSET_VALID 2204 | CCB_TRANS_BUS_WIDTH_VALID; 2205 xpt_async(AC_TRANSFER_NEG, cts->ccb_h.path, cts); 2206 } 2207 2208 static void 2209 btmapmboxes(void *arg, bus_dma_segment_t *segs, int nseg, int error) 2210 { 2211 struct bt_softc* bt; 2212 2213 bt = (struct bt_softc*)arg; 2214 bt->mailbox_physbase = segs->ds_addr; 2215 } 2216 2217 static void 2218 btmapccbs(void *arg, bus_dma_segment_t *segs, int nseg, int error) 2219 { 2220 struct bt_softc* bt; 2221 2222 bt = (struct bt_softc*)arg; 2223 bt->bt_ccb_physbase = segs->ds_addr; 2224 } 2225 2226 static void 2227 btmapsgs(void *arg, bus_dma_segment_t *segs, int nseg, int error) 2228 { 2229 2230 struct bt_softc* bt; 2231 2232 bt = (struct bt_softc*)arg; 2233 SLIST_FIRST(&bt->sg_maps)->sg_physaddr = segs->ds_addr; 2234 } 2235 2236 static void 2237 btpoll(struct cam_sim *sim) 2238 { 2239 bt_intr(cam_sim_softc(sim)); 2240 } 2241 2242 void 2243 bttimeout(void *arg) 2244 { 2245 struct bt_ccb *bccb; 2246 union ccb *ccb; 2247 struct bt_softc *bt; 2248 int s; 2249 2250 bccb = (struct bt_ccb *)arg; 2251 ccb = bccb->ccb; 2252 bt = (struct bt_softc *)ccb->ccb_h.ccb_bt_ptr; 2253 xpt_print_path(ccb->ccb_h.path); 2254 printf("CCB %p - timed out\n", (void *)bccb); 2255 2256 s = splcam(); 2257 2258 if ((bccb->flags & BCCB_ACTIVE) == 0) { 2259 xpt_print_path(ccb->ccb_h.path); 2260 printf("CCB %p - timed out CCB already completed\n", 2261 (void *)bccb); 2262 splx(s); 2263 return; 2264 } 2265 2266 /* 2267 * In order to simplify the recovery process, we ask the XPT 2268 * layer to halt the queue of new transactions and we traverse 2269 * the list of pending CCBs and remove their timeouts. This 2270 * means that the driver attempts to clear only one error 2271 * condition at a time. In general, timeouts that occur 2272 * close together are related anyway, so there is no benefit 2273 * in attempting to handle errors in parrallel. Timeouts will 2274 * be reinstated when the recovery process ends. 2275 */ 2276 if ((bccb->flags & BCCB_DEVICE_RESET) == 0) { 2277 struct ccb_hdr *ccb_h; 2278 2279 if ((bccb->flags & BCCB_RELEASE_SIMQ) == 0) { 2280 xpt_freeze_simq(bt->sim, /*count*/1); 2281 bccb->flags |= BCCB_RELEASE_SIMQ; 2282 } 2283 2284 ccb_h = LIST_FIRST(&bt->pending_ccbs); 2285 while (ccb_h != NULL) { 2286 struct bt_ccb *pending_bccb; 2287 2288 pending_bccb = (struct bt_ccb *)ccb_h->ccb_bccb_ptr; 2289 untimeout(bttimeout, pending_bccb, ccb_h->timeout_ch); 2290 ccb_h = LIST_NEXT(ccb_h, sim_links.le); 2291 } 2292 } 2293 2294 if ((bccb->flags & BCCB_DEVICE_RESET) != 0 2295 || bt->cur_outbox->action_code != BMBO_FREE 2296 || ((bccb->hccb.tag_enable == TRUE) 2297 && (bt->firmware_ver[0] < '5'))) { 2298 /* 2299 * Try a full host adapter/SCSI bus reset. 2300 * We do this only if we have already attempted 2301 * to clear the condition with a BDR, or we cannot 2302 * attempt a BDR for lack of mailbox resources 2303 * or because of faulty firmware. It turns out 2304 * that firmware versions prior to 5.xx treat BDRs 2305 * as untagged commands that cannot be sent until 2306 * all outstanding tagged commands have been processed. 2307 * This makes it somewhat difficult to use a BDR to 2308 * clear up a problem with an uncompleted tagged command. 2309 */ 2310 ccb->ccb_h.status = CAM_CMD_TIMEOUT; 2311 btreset(bt, /*hardreset*/TRUE); 2312 printf("%s: No longer in timeout\n", bt_name(bt)); 2313 } else { 2314 /* 2315 * Send a Bus Device Reset message: 2316 * The target that is holding up the bus may not 2317 * be the same as the one that triggered this timeout 2318 * (different commands have different timeout lengths), 2319 * but we have no way of determining this from our 2320 * timeout handler. Our strategy here is to queue a 2321 * BDR message to the target of the timed out command. 2322 * If this fails, we'll get another timeout 2 seconds 2323 * later which will attempt a bus reset. 2324 */ 2325 bccb->flags |= BCCB_DEVICE_RESET; 2326 ccb->ccb_h.timeout_ch = 2327 timeout(bttimeout, (caddr_t)bccb, 2 * hz); 2328 2329 bt->recovery_bccb->hccb.opcode = INITIATOR_BUS_DEV_RESET; 2330 2331 /* No Data Transfer */ 2332 bt->recovery_bccb->hccb.datain = TRUE; 2333 bt->recovery_bccb->hccb.dataout = TRUE; 2334 bt->recovery_bccb->hccb.btstat = 0; 2335 bt->recovery_bccb->hccb.sdstat = 0; 2336 bt->recovery_bccb->hccb.target_id = ccb->ccb_h.target_id; 2337 2338 /* Tell the adapter about this command */ 2339 bt->cur_outbox->ccb_addr = btccbvtop(bt, bt->recovery_bccb); 2340 bt->cur_outbox->action_code = BMBO_START; 2341 bt_outb(bt, COMMAND_REG, BOP_START_MBOX); 2342 btnextoutbox(bt); 2343 } 2344 2345 splx(s); 2346 } 2347 2348