1 /****************************************************************************** 2 3 Copyright (c) 2001-2014, Intel Corporation 4 All rights reserved. 5 6 Redistribution and use in source and binary forms, with or without 7 modification, are permitted provided that the following conditions are met: 8 9 1. Redistributions of source code must retain the above copyright notice, 10 this list of conditions and the following disclaimer. 11 12 2. Redistributions in binary form must reproduce the above copyright 13 notice, this list of conditions and the following disclaimer in the 14 documentation and/or other materials provided with the distribution. 15 16 3. Neither the name of the Intel Corporation nor the names of its 17 contributors may be used to endorse or promote products derived from 18 this software without specific prior written permission. 19 20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 POSSIBILITY OF SUCH DAMAGE. 31 32 ******************************************************************************/ 33 /*$FreeBSD$*/ 34 35 #include "ixgbe_type.h" 36 #include "ixgbe_82599.h" 37 #include "ixgbe_api.h" 38 #include "ixgbe_common.h" 39 #include "ixgbe_phy.h" 40 41 #define IXGBE_82599_MAX_TX_QUEUES 128 42 #define IXGBE_82599_MAX_RX_QUEUES 128 43 #define IXGBE_82599_RAR_ENTRIES 128 44 #define IXGBE_82599_MC_TBL_SIZE 128 45 #define IXGBE_82599_VFT_TBL_SIZE 128 46 #define IXGBE_82599_RX_PB_SIZE 512 47 48 static s32 ixgbe_setup_copper_link_82599(struct ixgbe_hw *hw, 49 ixgbe_link_speed speed, 50 bool autoneg_wait_to_complete); 51 static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw); 52 static s32 ixgbe_read_eeprom_82599(struct ixgbe_hw *hw, 53 u16 offset, u16 *data); 54 static s32 ixgbe_read_eeprom_buffer_82599(struct ixgbe_hw *hw, u16 offset, 55 u16 words, u16 *data); 56 static s32 ixgbe_read_i2c_byte_82599(struct ixgbe_hw *hw, u8 byte_offset, 57 u8 dev_addr, u8 *data); 58 static s32 ixgbe_write_i2c_byte_82599(struct ixgbe_hw *hw, u8 byte_offset, 59 u8 dev_addr, u8 data); 60 61 void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw) 62 { 63 struct ixgbe_mac_info *mac = &hw->mac; 64 65 DEBUGFUNC("ixgbe_init_mac_link_ops_82599"); 66 67 /* 68 * enable the laser control functions for SFP+ fiber 69 * and MNG not enabled 70 */ 71 if ((mac->ops.get_media_type(hw) == ixgbe_media_type_fiber) && 72 !ixgbe_mng_enabled(hw)) { 73 mac->ops.disable_tx_laser = 74 ixgbe_disable_tx_laser_multispeed_fiber; 75 mac->ops.enable_tx_laser = 76 ixgbe_enable_tx_laser_multispeed_fiber; 77 mac->ops.flap_tx_laser = ixgbe_flap_tx_laser_multispeed_fiber; 78 79 } else { 80 mac->ops.disable_tx_laser = NULL; 81 mac->ops.enable_tx_laser = NULL; 82 mac->ops.flap_tx_laser = NULL; 83 } 84 85 if (hw->phy.multispeed_fiber) { 86 /* Set up dual speed SFP+ support */ 87 mac->ops.setup_link = ixgbe_setup_mac_link_multispeed_fiber; 88 mac->ops.setup_mac_link = ixgbe_setup_mac_link_82599; 89 mac->ops.set_rate_select_speed = 90 ixgbe_set_hard_rate_select_speed; 91 if (ixgbe_get_media_type(hw) == ixgbe_media_type_fiber_fixed) 92 mac->ops.set_rate_select_speed = 93 ixgbe_set_soft_rate_select_speed; 94 } else { 95 if ((ixgbe_get_media_type(hw) == ixgbe_media_type_backplane) && 96 (hw->phy.smart_speed == ixgbe_smart_speed_auto || 97 hw->phy.smart_speed == ixgbe_smart_speed_on) && 98 !ixgbe_verify_lesm_fw_enabled_82599(hw)) { 99 mac->ops.setup_link = ixgbe_setup_mac_link_smartspeed; 100 } else { 101 mac->ops.setup_link = ixgbe_setup_mac_link_82599; 102 } 103 } 104 } 105 106 /** 107 * ixgbe_init_phy_ops_82599 - PHY/SFP specific init 108 * @hw: pointer to hardware structure 109 * 110 * Initialize any function pointers that were not able to be 111 * set during init_shared_code because the PHY/SFP type was 112 * not known. Perform the SFP init if necessary. 113 * 114 **/ 115 s32 ixgbe_init_phy_ops_82599(struct ixgbe_hw *hw) 116 { 117 struct ixgbe_mac_info *mac = &hw->mac; 118 struct ixgbe_phy_info *phy = &hw->phy; 119 s32 ret_val = IXGBE_SUCCESS; 120 u32 esdp; 121 122 DEBUGFUNC("ixgbe_init_phy_ops_82599"); 123 124 if (hw->device_id == IXGBE_DEV_ID_82599_QSFP_SF_QP) { 125 /* Store flag indicating I2C bus access control unit. */ 126 hw->phy.qsfp_shared_i2c_bus = TRUE; 127 128 /* Initialize access to QSFP+ I2C bus */ 129 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 130 esdp |= IXGBE_ESDP_SDP0_DIR; 131 esdp &= ~IXGBE_ESDP_SDP1_DIR; 132 esdp &= ~IXGBE_ESDP_SDP0; 133 esdp &= ~IXGBE_ESDP_SDP0_NATIVE; 134 esdp &= ~IXGBE_ESDP_SDP1_NATIVE; 135 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 136 IXGBE_WRITE_FLUSH(hw); 137 138 phy->ops.read_i2c_byte = ixgbe_read_i2c_byte_82599; 139 phy->ops.write_i2c_byte = ixgbe_write_i2c_byte_82599; 140 } 141 /* Identify the PHY or SFP module */ 142 ret_val = phy->ops.identify(hw); 143 if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED) 144 goto init_phy_ops_out; 145 146 /* Setup function pointers based on detected SFP module and speeds */ 147 ixgbe_init_mac_link_ops_82599(hw); 148 if (hw->phy.sfp_type != ixgbe_sfp_type_unknown) 149 hw->phy.ops.reset = NULL; 150 151 /* If copper media, overwrite with copper function pointers */ 152 if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) { 153 mac->ops.setup_link = ixgbe_setup_copper_link_82599; 154 mac->ops.get_link_capabilities = 155 ixgbe_get_copper_link_capabilities_generic; 156 } 157 158 /* Set necessary function pointers based on PHY type */ 159 switch (hw->phy.type) { 160 case ixgbe_phy_tn: 161 phy->ops.setup_link = ixgbe_setup_phy_link_tnx; 162 phy->ops.check_link = ixgbe_check_phy_link_tnx; 163 phy->ops.get_firmware_version = 164 ixgbe_get_phy_firmware_version_tnx; 165 break; 166 default: 167 break; 168 } 169 init_phy_ops_out: 170 return ret_val; 171 } 172 173 s32 ixgbe_setup_sfp_modules_82599(struct ixgbe_hw *hw) 174 { 175 s32 ret_val = IXGBE_SUCCESS; 176 u16 list_offset, data_offset, data_value; 177 178 DEBUGFUNC("ixgbe_setup_sfp_modules_82599"); 179 180 if (hw->phy.sfp_type != ixgbe_sfp_type_unknown) { 181 ixgbe_init_mac_link_ops_82599(hw); 182 183 hw->phy.ops.reset = NULL; 184 185 ret_val = ixgbe_get_sfp_init_sequence_offsets(hw, &list_offset, 186 &data_offset); 187 if (ret_val != IXGBE_SUCCESS) 188 goto setup_sfp_out; 189 190 /* PHY config will finish before releasing the semaphore */ 191 ret_val = hw->mac.ops.acquire_swfw_sync(hw, 192 IXGBE_GSSR_MAC_CSR_SM); 193 if (ret_val != IXGBE_SUCCESS) { 194 ret_val = IXGBE_ERR_SWFW_SYNC; 195 goto setup_sfp_out; 196 } 197 198 if (hw->eeprom.ops.read(hw, ++data_offset, &data_value)) 199 goto setup_sfp_err; 200 while (data_value != 0xffff) { 201 IXGBE_WRITE_REG(hw, IXGBE_CORECTL, data_value); 202 IXGBE_WRITE_FLUSH(hw); 203 if (hw->eeprom.ops.read(hw, ++data_offset, &data_value)) 204 goto setup_sfp_err; 205 } 206 207 /* Release the semaphore */ 208 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM); 209 /* Delay obtaining semaphore again to allow FW access 210 * prot_autoc_write uses the semaphore too. 211 */ 212 msec_delay(hw->eeprom.semaphore_delay); 213 214 /* Restart DSP and set SFI mode */ 215 ret_val = hw->mac.ops.prot_autoc_write(hw, 216 hw->mac.orig_autoc | IXGBE_AUTOC_LMS_10G_SERIAL, 217 FALSE); 218 219 if (ret_val) { 220 DEBUGOUT("sfp module setup not complete\n"); 221 ret_val = IXGBE_ERR_SFP_SETUP_NOT_COMPLETE; 222 goto setup_sfp_out; 223 } 224 225 } 226 227 setup_sfp_out: 228 return ret_val; 229 230 setup_sfp_err: 231 /* Release the semaphore */ 232 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM); 233 /* Delay obtaining semaphore again to allow FW access */ 234 msec_delay(hw->eeprom.semaphore_delay); 235 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 236 "eeprom read at offset %d failed", data_offset); 237 return IXGBE_ERR_PHY; 238 } 239 240 /** 241 * prot_autoc_read_82599 - Hides MAC differences needed for AUTOC read 242 * @hw: pointer to hardware structure 243 * @locked: Return the if we locked for this read. 244 * @reg_val: Value we read from AUTOC 245 * 246 * For this part (82599) we need to wrap read-modify-writes with a possible 247 * FW/SW lock. It is assumed this lock will be freed with the next 248 * prot_autoc_write_82599(). 249 */ 250 s32 prot_autoc_read_82599(struct ixgbe_hw *hw, bool *locked, u32 *reg_val) 251 { 252 s32 ret_val; 253 254 *locked = FALSE; 255 /* If LESM is on then we need to hold the SW/FW semaphore. */ 256 if (ixgbe_verify_lesm_fw_enabled_82599(hw)) { 257 ret_val = hw->mac.ops.acquire_swfw_sync(hw, 258 IXGBE_GSSR_MAC_CSR_SM); 259 if (ret_val != IXGBE_SUCCESS) 260 return IXGBE_ERR_SWFW_SYNC; 261 262 *locked = TRUE; 263 } 264 265 *reg_val = IXGBE_READ_REG(hw, IXGBE_AUTOC); 266 return IXGBE_SUCCESS; 267 } 268 269 /** 270 * prot_autoc_write_82599 - Hides MAC differences needed for AUTOC write 271 * @hw: pointer to hardware structure 272 * @reg_val: value to write to AUTOC 273 * @locked: bool to indicate whether the SW/FW lock was already taken by 274 * previous proc_autoc_read_82599. 275 * 276 * This part (82599) may need to hold the SW/FW lock around all writes to 277 * AUTOC. Likewise after a write we need to do a pipeline reset. 278 */ 279 s32 prot_autoc_write_82599(struct ixgbe_hw *hw, u32 autoc, bool locked) 280 { 281 s32 ret_val = IXGBE_SUCCESS; 282 283 /* Blocked by MNG FW so bail */ 284 if (ixgbe_check_reset_blocked(hw)) 285 goto out; 286 287 /* We only need to get the lock if: 288 * - We didn't do it already (in the read part of a read-modify-write) 289 * - LESM is enabled. 290 */ 291 if (!locked && ixgbe_verify_lesm_fw_enabled_82599(hw)) { 292 ret_val = hw->mac.ops.acquire_swfw_sync(hw, 293 IXGBE_GSSR_MAC_CSR_SM); 294 if (ret_val != IXGBE_SUCCESS) 295 return IXGBE_ERR_SWFW_SYNC; 296 297 locked = TRUE; 298 } 299 300 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc); 301 ret_val = ixgbe_reset_pipeline_82599(hw); 302 303 out: 304 /* Free the SW/FW semaphore as we either grabbed it here or 305 * already had it when this function was called. 306 */ 307 if (locked) 308 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM); 309 310 return ret_val; 311 } 312 313 /** 314 * ixgbe_init_ops_82599 - Inits func ptrs and MAC type 315 * @hw: pointer to hardware structure 316 * 317 * Initialize the function pointers and assign the MAC type for 82599. 318 * Does not touch the hardware. 319 **/ 320 321 s32 ixgbe_init_ops_82599(struct ixgbe_hw *hw) 322 { 323 struct ixgbe_mac_info *mac = &hw->mac; 324 struct ixgbe_phy_info *phy = &hw->phy; 325 struct ixgbe_eeprom_info *eeprom = &hw->eeprom; 326 s32 ret_val; 327 328 DEBUGFUNC("ixgbe_init_ops_82599"); 329 330 ixgbe_init_phy_ops_generic(hw); 331 ret_val = ixgbe_init_ops_generic(hw); 332 333 /* PHY */ 334 phy->ops.identify = ixgbe_identify_phy_82599; 335 phy->ops.init = ixgbe_init_phy_ops_82599; 336 337 /* MAC */ 338 mac->ops.reset_hw = ixgbe_reset_hw_82599; 339 mac->ops.enable_relaxed_ordering = ixgbe_enable_relaxed_ordering_gen2; 340 mac->ops.get_media_type = ixgbe_get_media_type_82599; 341 mac->ops.get_supported_physical_layer = 342 ixgbe_get_supported_physical_layer_82599; 343 mac->ops.disable_sec_rx_path = ixgbe_disable_sec_rx_path_generic; 344 mac->ops.enable_sec_rx_path = ixgbe_enable_sec_rx_path_generic; 345 mac->ops.enable_rx_dma = ixgbe_enable_rx_dma_82599; 346 mac->ops.read_analog_reg8 = ixgbe_read_analog_reg8_82599; 347 mac->ops.write_analog_reg8 = ixgbe_write_analog_reg8_82599; 348 mac->ops.start_hw = ixgbe_start_hw_82599; 349 mac->ops.get_san_mac_addr = ixgbe_get_san_mac_addr_generic; 350 mac->ops.set_san_mac_addr = ixgbe_set_san_mac_addr_generic; 351 mac->ops.get_device_caps = ixgbe_get_device_caps_generic; 352 mac->ops.get_wwn_prefix = ixgbe_get_wwn_prefix_generic; 353 mac->ops.get_fcoe_boot_status = ixgbe_get_fcoe_boot_status_generic; 354 mac->ops.prot_autoc_read = prot_autoc_read_82599; 355 mac->ops.prot_autoc_write = prot_autoc_write_82599; 356 357 /* RAR, Multicast, VLAN */ 358 mac->ops.set_vmdq = ixgbe_set_vmdq_generic; 359 mac->ops.set_vmdq_san_mac = ixgbe_set_vmdq_san_mac_generic; 360 mac->ops.clear_vmdq = ixgbe_clear_vmdq_generic; 361 mac->ops.insert_mac_addr = ixgbe_insert_mac_addr_generic; 362 mac->rar_highwater = 1; 363 mac->ops.set_vfta = ixgbe_set_vfta_generic; 364 mac->ops.set_vlvf = ixgbe_set_vlvf_generic; 365 mac->ops.clear_vfta = ixgbe_clear_vfta_generic; 366 mac->ops.init_uta_tables = ixgbe_init_uta_tables_generic; 367 mac->ops.setup_sfp = ixgbe_setup_sfp_modules_82599; 368 mac->ops.set_mac_anti_spoofing = ixgbe_set_mac_anti_spoofing; 369 mac->ops.set_vlan_anti_spoofing = ixgbe_set_vlan_anti_spoofing; 370 371 /* Link */ 372 mac->ops.get_link_capabilities = ixgbe_get_link_capabilities_82599; 373 mac->ops.check_link = ixgbe_check_mac_link_generic; 374 mac->ops.setup_rxpba = ixgbe_set_rxpba_generic; 375 ixgbe_init_mac_link_ops_82599(hw); 376 377 mac->mcft_size = IXGBE_82599_MC_TBL_SIZE; 378 mac->vft_size = IXGBE_82599_VFT_TBL_SIZE; 379 mac->num_rar_entries = IXGBE_82599_RAR_ENTRIES; 380 mac->rx_pb_size = IXGBE_82599_RX_PB_SIZE; 381 mac->max_rx_queues = IXGBE_82599_MAX_RX_QUEUES; 382 mac->max_tx_queues = IXGBE_82599_MAX_TX_QUEUES; 383 mac->max_msix_vectors = ixgbe_get_pcie_msix_count_generic(hw); 384 385 mac->arc_subsystem_valid = (IXGBE_READ_REG(hw, IXGBE_FWSM) & 386 IXGBE_FWSM_MODE_MASK) ? TRUE : FALSE; 387 388 hw->mbx.ops.init_params = ixgbe_init_mbx_params_pf; 389 390 /* EEPROM */ 391 eeprom->ops.read = ixgbe_read_eeprom_82599; 392 eeprom->ops.read_buffer = ixgbe_read_eeprom_buffer_82599; 393 394 /* Manageability interface */ 395 mac->ops.set_fw_drv_ver = ixgbe_set_fw_drv_ver_generic; 396 397 398 mac->ops.get_rtrup2tc = ixgbe_dcb_get_rtrup2tc_generic; 399 400 return ret_val; 401 } 402 403 /** 404 * ixgbe_get_link_capabilities_82599 - Determines link capabilities 405 * @hw: pointer to hardware structure 406 * @speed: pointer to link speed 407 * @autoneg: TRUE when autoneg or autotry is enabled 408 * 409 * Determines the link capabilities by reading the AUTOC register. 410 **/ 411 s32 ixgbe_get_link_capabilities_82599(struct ixgbe_hw *hw, 412 ixgbe_link_speed *speed, 413 bool *autoneg) 414 { 415 s32 status = IXGBE_SUCCESS; 416 u32 autoc = 0; 417 418 DEBUGFUNC("ixgbe_get_link_capabilities_82599"); 419 420 421 /* Check if 1G SFP module. */ 422 if (hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core0 || 423 hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core1 || 424 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core0 || 425 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core1 || 426 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 || 427 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1) { 428 *speed = IXGBE_LINK_SPEED_1GB_FULL; 429 *autoneg = TRUE; 430 goto out; 431 } 432 433 /* 434 * Determine link capabilities based on the stored value of AUTOC, 435 * which represents EEPROM defaults. If AUTOC value has not 436 * been stored, use the current register values. 437 */ 438 if (hw->mac.orig_link_settings_stored) 439 autoc = hw->mac.orig_autoc; 440 else 441 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); 442 443 switch (autoc & IXGBE_AUTOC_LMS_MASK) { 444 case IXGBE_AUTOC_LMS_1G_LINK_NO_AN: 445 *speed = IXGBE_LINK_SPEED_1GB_FULL; 446 *autoneg = FALSE; 447 break; 448 449 case IXGBE_AUTOC_LMS_10G_LINK_NO_AN: 450 *speed = IXGBE_LINK_SPEED_10GB_FULL; 451 *autoneg = FALSE; 452 break; 453 454 case IXGBE_AUTOC_LMS_1G_AN: 455 *speed = IXGBE_LINK_SPEED_1GB_FULL; 456 *autoneg = TRUE; 457 break; 458 459 case IXGBE_AUTOC_LMS_10G_SERIAL: 460 *speed = IXGBE_LINK_SPEED_10GB_FULL; 461 *autoneg = FALSE; 462 break; 463 464 case IXGBE_AUTOC_LMS_KX4_KX_KR: 465 case IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN: 466 *speed = IXGBE_LINK_SPEED_UNKNOWN; 467 if (autoc & IXGBE_AUTOC_KR_SUPP) 468 *speed |= IXGBE_LINK_SPEED_10GB_FULL; 469 if (autoc & IXGBE_AUTOC_KX4_SUPP) 470 *speed |= IXGBE_LINK_SPEED_10GB_FULL; 471 if (autoc & IXGBE_AUTOC_KX_SUPP) 472 *speed |= IXGBE_LINK_SPEED_1GB_FULL; 473 *autoneg = TRUE; 474 break; 475 476 case IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII: 477 *speed = IXGBE_LINK_SPEED_100_FULL; 478 if (autoc & IXGBE_AUTOC_KR_SUPP) 479 *speed |= IXGBE_LINK_SPEED_10GB_FULL; 480 if (autoc & IXGBE_AUTOC_KX4_SUPP) 481 *speed |= IXGBE_LINK_SPEED_10GB_FULL; 482 if (autoc & IXGBE_AUTOC_KX_SUPP) 483 *speed |= IXGBE_LINK_SPEED_1GB_FULL; 484 *autoneg = TRUE; 485 break; 486 487 case IXGBE_AUTOC_LMS_SGMII_1G_100M: 488 *speed = IXGBE_LINK_SPEED_1GB_FULL | IXGBE_LINK_SPEED_100_FULL; 489 *autoneg = FALSE; 490 break; 491 492 default: 493 status = IXGBE_ERR_LINK_SETUP; 494 goto out; 495 break; 496 } 497 498 if (hw->phy.multispeed_fiber) { 499 *speed |= IXGBE_LINK_SPEED_10GB_FULL | 500 IXGBE_LINK_SPEED_1GB_FULL; 501 502 /* QSFP must not enable full auto-negotiation 503 * Limited autoneg is enabled at 1G 504 */ 505 if (hw->phy.media_type == ixgbe_media_type_fiber_qsfp) 506 *autoneg = FALSE; 507 else 508 *autoneg = TRUE; 509 } 510 511 out: 512 return status; 513 } 514 515 /** 516 * ixgbe_get_media_type_82599 - Get media type 517 * @hw: pointer to hardware structure 518 * 519 * Returns the media type (fiber, copper, backplane) 520 **/ 521 enum ixgbe_media_type ixgbe_get_media_type_82599(struct ixgbe_hw *hw) 522 { 523 enum ixgbe_media_type media_type; 524 525 DEBUGFUNC("ixgbe_get_media_type_82599"); 526 527 /* Detect if there is a copper PHY attached. */ 528 switch (hw->phy.type) { 529 case ixgbe_phy_cu_unknown: 530 case ixgbe_phy_tn: 531 media_type = ixgbe_media_type_copper; 532 goto out; 533 default: 534 break; 535 } 536 537 switch (hw->device_id) { 538 case IXGBE_DEV_ID_82599_KX4: 539 case IXGBE_DEV_ID_82599_KX4_MEZZ: 540 case IXGBE_DEV_ID_82599_COMBO_BACKPLANE: 541 case IXGBE_DEV_ID_82599_KR: 542 case IXGBE_DEV_ID_82599_BACKPLANE_FCOE: 543 case IXGBE_DEV_ID_82599_XAUI_LOM: 544 /* Default device ID is mezzanine card KX/KX4 */ 545 media_type = ixgbe_media_type_backplane; 546 break; 547 case IXGBE_DEV_ID_82599_SFP: 548 case IXGBE_DEV_ID_82599_SFP_FCOE: 549 case IXGBE_DEV_ID_82599_SFP_EM: 550 case IXGBE_DEV_ID_82599_SFP_SF2: 551 case IXGBE_DEV_ID_82599_SFP_SF_QP: 552 case IXGBE_DEV_ID_82599EN_SFP: 553 media_type = ixgbe_media_type_fiber; 554 break; 555 case IXGBE_DEV_ID_82599_CX4: 556 media_type = ixgbe_media_type_cx4; 557 break; 558 case IXGBE_DEV_ID_82599_T3_LOM: 559 media_type = ixgbe_media_type_copper; 560 break; 561 case IXGBE_DEV_ID_82599_QSFP_SF_QP: 562 media_type = ixgbe_media_type_fiber_qsfp; 563 break; 564 case IXGBE_DEV_ID_82599_BYPASS: 565 media_type = ixgbe_media_type_fiber_fixed; 566 hw->phy.multispeed_fiber = TRUE; 567 break; 568 default: 569 media_type = ixgbe_media_type_unknown; 570 break; 571 } 572 out: 573 return media_type; 574 } 575 576 /** 577 * ixgbe_stop_mac_link_on_d3_82599 - Disables link on D3 578 * @hw: pointer to hardware structure 579 * 580 * Disables link during D3 power down sequence. 581 * 582 **/ 583 void ixgbe_stop_mac_link_on_d3_82599(struct ixgbe_hw *hw) 584 { 585 u32 autoc2_reg; 586 u16 ee_ctrl_2 = 0; 587 588 DEBUGFUNC("ixgbe_stop_mac_link_on_d3_82599"); 589 ixgbe_read_eeprom(hw, IXGBE_EEPROM_CTRL_2, &ee_ctrl_2); 590 591 if (!ixgbe_mng_present(hw) && !hw->wol_enabled && 592 ee_ctrl_2 & IXGBE_EEPROM_CCD_BIT) { 593 autoc2_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC2); 594 autoc2_reg |= IXGBE_AUTOC2_LINK_DISABLE_ON_D3_MASK; 595 IXGBE_WRITE_REG(hw, IXGBE_AUTOC2, autoc2_reg); 596 } 597 } 598 599 /** 600 * ixgbe_start_mac_link_82599 - Setup MAC link settings 601 * @hw: pointer to hardware structure 602 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed 603 * 604 * Configures link settings based on values in the ixgbe_hw struct. 605 * Restarts the link. Performs autonegotiation if needed. 606 **/ 607 s32 ixgbe_start_mac_link_82599(struct ixgbe_hw *hw, 608 bool autoneg_wait_to_complete) 609 { 610 u32 autoc_reg; 611 u32 links_reg; 612 u32 i; 613 s32 status = IXGBE_SUCCESS; 614 bool got_lock = FALSE; 615 616 DEBUGFUNC("ixgbe_start_mac_link_82599"); 617 618 619 /* reset_pipeline requires us to hold this lock as it writes to 620 * AUTOC. 621 */ 622 if (ixgbe_verify_lesm_fw_enabled_82599(hw)) { 623 status = hw->mac.ops.acquire_swfw_sync(hw, 624 IXGBE_GSSR_MAC_CSR_SM); 625 if (status != IXGBE_SUCCESS) 626 goto out; 627 628 got_lock = TRUE; 629 } 630 631 /* Restart link */ 632 ixgbe_reset_pipeline_82599(hw); 633 634 if (got_lock) 635 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM); 636 637 /* Only poll for autoneg to complete if specified to do so */ 638 if (autoneg_wait_to_complete) { 639 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); 640 if ((autoc_reg & IXGBE_AUTOC_LMS_MASK) == 641 IXGBE_AUTOC_LMS_KX4_KX_KR || 642 (autoc_reg & IXGBE_AUTOC_LMS_MASK) == 643 IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN || 644 (autoc_reg & IXGBE_AUTOC_LMS_MASK) == 645 IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) { 646 links_reg = 0; /* Just in case Autoneg time = 0 */ 647 for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) { 648 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); 649 if (links_reg & IXGBE_LINKS_KX_AN_COMP) 650 break; 651 msec_delay(100); 652 } 653 if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) { 654 status = IXGBE_ERR_AUTONEG_NOT_COMPLETE; 655 DEBUGOUT("Autoneg did not complete.\n"); 656 } 657 } 658 } 659 660 /* Add delay to filter out noises during initial link setup */ 661 msec_delay(50); 662 663 out: 664 return status; 665 } 666 667 /** 668 * ixgbe_disable_tx_laser_multispeed_fiber - Disable Tx laser 669 * @hw: pointer to hardware structure 670 * 671 * The base drivers may require better control over SFP+ module 672 * PHY states. This includes selectively shutting down the Tx 673 * laser on the PHY, effectively halting physical link. 674 **/ 675 void ixgbe_disable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw) 676 { 677 u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP); 678 679 /* Blocked by MNG FW so bail */ 680 if (ixgbe_check_reset_blocked(hw)) 681 return; 682 683 /* Disable Tx laser; allow 100us to go dark per spec */ 684 esdp_reg |= IXGBE_ESDP_SDP3; 685 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); 686 IXGBE_WRITE_FLUSH(hw); 687 usec_delay(100); 688 } 689 690 /** 691 * ixgbe_enable_tx_laser_multispeed_fiber - Enable Tx laser 692 * @hw: pointer to hardware structure 693 * 694 * The base drivers may require better control over SFP+ module 695 * PHY states. This includes selectively turning on the Tx 696 * laser on the PHY, effectively starting physical link. 697 **/ 698 void ixgbe_enable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw) 699 { 700 u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP); 701 702 /* Enable Tx laser; allow 100ms to light up */ 703 esdp_reg &= ~IXGBE_ESDP_SDP3; 704 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); 705 IXGBE_WRITE_FLUSH(hw); 706 msec_delay(100); 707 } 708 709 /** 710 * ixgbe_flap_tx_laser_multispeed_fiber - Flap Tx laser 711 * @hw: pointer to hardware structure 712 * 713 * When the driver changes the link speeds that it can support, 714 * it sets autotry_restart to TRUE to indicate that we need to 715 * initiate a new autotry session with the link partner. To do 716 * so, we set the speed then disable and re-enable the Tx laser, to 717 * alert the link partner that it also needs to restart autotry on its 718 * end. This is consistent with TRUE clause 37 autoneg, which also 719 * involves a loss of signal. 720 **/ 721 void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw) 722 { 723 DEBUGFUNC("ixgbe_flap_tx_laser_multispeed_fiber"); 724 725 /* Blocked by MNG FW so bail */ 726 if (ixgbe_check_reset_blocked(hw)) 727 return; 728 729 if (hw->mac.autotry_restart) { 730 ixgbe_disable_tx_laser_multispeed_fiber(hw); 731 ixgbe_enable_tx_laser_multispeed_fiber(hw); 732 hw->mac.autotry_restart = FALSE; 733 } 734 } 735 736 /** 737 * ixgbe_set_hard_rate_select_speed - Set module link speed 738 * @hw: pointer to hardware structure 739 * @speed: link speed to set 740 * 741 * Set module link speed via RS0/RS1 rate select pins. 742 */ 743 void ixgbe_set_hard_rate_select_speed(struct ixgbe_hw *hw, 744 ixgbe_link_speed speed) 745 { 746 u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP); 747 748 switch (speed) { 749 case IXGBE_LINK_SPEED_10GB_FULL: 750 esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5); 751 break; 752 case IXGBE_LINK_SPEED_1GB_FULL: 753 esdp_reg &= ~IXGBE_ESDP_SDP5; 754 esdp_reg |= IXGBE_ESDP_SDP5_DIR; 755 break; 756 default: 757 DEBUGOUT("Invalid fixed module speed\n"); 758 return; 759 } 760 761 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); 762 IXGBE_WRITE_FLUSH(hw); 763 } 764 765 /** 766 * ixgbe_setup_mac_link_smartspeed - Set MAC link speed using SmartSpeed 767 * @hw: pointer to hardware structure 768 * @speed: new link speed 769 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed 770 * 771 * Implements the Intel SmartSpeed algorithm. 772 **/ 773 s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw, 774 ixgbe_link_speed speed, 775 bool autoneg_wait_to_complete) 776 { 777 s32 status = IXGBE_SUCCESS; 778 ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN; 779 s32 i, j; 780 bool link_up = FALSE; 781 u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); 782 783 DEBUGFUNC("ixgbe_setup_mac_link_smartspeed"); 784 785 /* Set autoneg_advertised value based on input link speed */ 786 hw->phy.autoneg_advertised = 0; 787 788 if (speed & IXGBE_LINK_SPEED_10GB_FULL) 789 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; 790 791 if (speed & IXGBE_LINK_SPEED_1GB_FULL) 792 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; 793 794 if (speed & IXGBE_LINK_SPEED_100_FULL) 795 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_100_FULL; 796 797 /* 798 * Implement Intel SmartSpeed algorithm. SmartSpeed will reduce the 799 * autoneg advertisement if link is unable to be established at the 800 * highest negotiated rate. This can sometimes happen due to integrity 801 * issues with the physical media connection. 802 */ 803 804 /* First, try to get link with full advertisement */ 805 hw->phy.smart_speed_active = FALSE; 806 for (j = 0; j < IXGBE_SMARTSPEED_MAX_RETRIES; j++) { 807 status = ixgbe_setup_mac_link_82599(hw, speed, 808 autoneg_wait_to_complete); 809 if (status != IXGBE_SUCCESS) 810 goto out; 811 812 /* 813 * Wait for the controller to acquire link. Per IEEE 802.3ap, 814 * Section 73.10.2, we may have to wait up to 500ms if KR is 815 * attempted, or 200ms if KX/KX4/BX/BX4 is attempted, per 816 * Table 9 in the AN MAS. 817 */ 818 for (i = 0; i < 5; i++) { 819 msec_delay(100); 820 821 /* If we have link, just jump out */ 822 status = ixgbe_check_link(hw, &link_speed, &link_up, 823 FALSE); 824 if (status != IXGBE_SUCCESS) 825 goto out; 826 827 if (link_up) 828 goto out; 829 } 830 } 831 832 /* 833 * We didn't get link. If we advertised KR plus one of KX4/KX 834 * (or BX4/BX), then disable KR and try again. 835 */ 836 if (((autoc_reg & IXGBE_AUTOC_KR_SUPP) == 0) || 837 ((autoc_reg & IXGBE_AUTOC_KX4_KX_SUPP_MASK) == 0)) 838 goto out; 839 840 /* Turn SmartSpeed on to disable KR support */ 841 hw->phy.smart_speed_active = TRUE; 842 status = ixgbe_setup_mac_link_82599(hw, speed, 843 autoneg_wait_to_complete); 844 if (status != IXGBE_SUCCESS) 845 goto out; 846 847 /* 848 * Wait for the controller to acquire link. 600ms will allow for 849 * the AN link_fail_inhibit_timer as well for multiple cycles of 850 * parallel detect, both 10g and 1g. This allows for the maximum 851 * connect attempts as defined in the AN MAS table 73-7. 852 */ 853 for (i = 0; i < 6; i++) { 854 msec_delay(100); 855 856 /* If we have link, just jump out */ 857 status = ixgbe_check_link(hw, &link_speed, &link_up, FALSE); 858 if (status != IXGBE_SUCCESS) 859 goto out; 860 861 if (link_up) 862 goto out; 863 } 864 865 /* We didn't get link. Turn SmartSpeed back off. */ 866 hw->phy.smart_speed_active = FALSE; 867 status = ixgbe_setup_mac_link_82599(hw, speed, 868 autoneg_wait_to_complete); 869 870 out: 871 if (link_up && (link_speed == IXGBE_LINK_SPEED_1GB_FULL)) 872 DEBUGOUT("Smartspeed has downgraded the link speed " 873 "from the maximum advertised\n"); 874 return status; 875 } 876 877 /** 878 * ixgbe_setup_mac_link_82599 - Set MAC link speed 879 * @hw: pointer to hardware structure 880 * @speed: new link speed 881 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed 882 * 883 * Set the link speed in the AUTOC register and restarts link. 884 **/ 885 s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw, 886 ixgbe_link_speed speed, 887 bool autoneg_wait_to_complete) 888 { 889 bool autoneg = FALSE; 890 s32 status = IXGBE_SUCCESS; 891 u32 pma_pmd_1g, link_mode; 892 u32 current_autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); /* holds the value of AUTOC register at this current point in time */ 893 u32 orig_autoc = 0; /* holds the cached value of AUTOC register */ 894 u32 autoc = current_autoc; /* Temporary variable used for comparison purposes */ 895 u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2); 896 u32 pma_pmd_10g_serial = autoc2 & IXGBE_AUTOC2_10G_SERIAL_PMA_PMD_MASK; 897 u32 links_reg; 898 u32 i; 899 ixgbe_link_speed link_capabilities = IXGBE_LINK_SPEED_UNKNOWN; 900 901 DEBUGFUNC("ixgbe_setup_mac_link_82599"); 902 903 /* Check to see if speed passed in is supported. */ 904 status = ixgbe_get_link_capabilities(hw, &link_capabilities, &autoneg); 905 if (status) 906 goto out; 907 908 speed &= link_capabilities; 909 910 if (speed == IXGBE_LINK_SPEED_UNKNOWN) { 911 status = IXGBE_ERR_LINK_SETUP; 912 goto out; 913 } 914 915 /* Use stored value (EEPROM defaults) of AUTOC to find KR/KX4 support*/ 916 if (hw->mac.orig_link_settings_stored) 917 orig_autoc = hw->mac.orig_autoc; 918 else 919 orig_autoc = autoc; 920 921 link_mode = autoc & IXGBE_AUTOC_LMS_MASK; 922 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK; 923 924 if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR || 925 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN || 926 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) { 927 /* Set KX4/KX/KR support according to speed requested */ 928 autoc &= ~(IXGBE_AUTOC_KX4_KX_SUPP_MASK | IXGBE_AUTOC_KR_SUPP); 929 if (speed & IXGBE_LINK_SPEED_10GB_FULL) { 930 if (orig_autoc & IXGBE_AUTOC_KX4_SUPP) 931 autoc |= IXGBE_AUTOC_KX4_SUPP; 932 if ((orig_autoc & IXGBE_AUTOC_KR_SUPP) && 933 (hw->phy.smart_speed_active == FALSE)) 934 autoc |= IXGBE_AUTOC_KR_SUPP; 935 } 936 if (speed & IXGBE_LINK_SPEED_1GB_FULL) 937 autoc |= IXGBE_AUTOC_KX_SUPP; 938 } else if ((pma_pmd_1g == IXGBE_AUTOC_1G_SFI) && 939 (link_mode == IXGBE_AUTOC_LMS_1G_LINK_NO_AN || 940 link_mode == IXGBE_AUTOC_LMS_1G_AN)) { 941 /* Switch from 1G SFI to 10G SFI if requested */ 942 if ((speed == IXGBE_LINK_SPEED_10GB_FULL) && 943 (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI)) { 944 autoc &= ~IXGBE_AUTOC_LMS_MASK; 945 autoc |= IXGBE_AUTOC_LMS_10G_SERIAL; 946 } 947 } else if ((pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI) && 948 (link_mode == IXGBE_AUTOC_LMS_10G_SERIAL)) { 949 /* Switch from 10G SFI to 1G SFI if requested */ 950 if ((speed == IXGBE_LINK_SPEED_1GB_FULL) && 951 (pma_pmd_1g == IXGBE_AUTOC_1G_SFI)) { 952 autoc &= ~IXGBE_AUTOC_LMS_MASK; 953 if (autoneg || hw->phy.type == ixgbe_phy_qsfp_intel) 954 autoc |= IXGBE_AUTOC_LMS_1G_AN; 955 else 956 autoc |= IXGBE_AUTOC_LMS_1G_LINK_NO_AN; 957 } 958 } 959 960 if (autoc != current_autoc) { 961 /* Restart link */ 962 status = hw->mac.ops.prot_autoc_write(hw, autoc, FALSE); 963 if (status != IXGBE_SUCCESS) 964 goto out; 965 966 /* Only poll for autoneg to complete if specified to do so */ 967 if (autoneg_wait_to_complete) { 968 if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR || 969 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN || 970 link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) { 971 links_reg = 0; /*Just in case Autoneg time=0*/ 972 for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) { 973 links_reg = 974 IXGBE_READ_REG(hw, IXGBE_LINKS); 975 if (links_reg & IXGBE_LINKS_KX_AN_COMP) 976 break; 977 msec_delay(100); 978 } 979 if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) { 980 status = 981 IXGBE_ERR_AUTONEG_NOT_COMPLETE; 982 DEBUGOUT("Autoneg did not complete.\n"); 983 } 984 } 985 } 986 987 /* Add delay to filter out noises during initial link setup */ 988 msec_delay(50); 989 } 990 991 out: 992 return status; 993 } 994 995 /** 996 * ixgbe_setup_copper_link_82599 - Set the PHY autoneg advertised field 997 * @hw: pointer to hardware structure 998 * @speed: new link speed 999 * @autoneg_wait_to_complete: TRUE if waiting is needed to complete 1000 * 1001 * Restarts link on PHY and MAC based on settings passed in. 1002 **/ 1003 static s32 ixgbe_setup_copper_link_82599(struct ixgbe_hw *hw, 1004 ixgbe_link_speed speed, 1005 bool autoneg_wait_to_complete) 1006 { 1007 s32 status; 1008 1009 DEBUGFUNC("ixgbe_setup_copper_link_82599"); 1010 1011 /* Setup the PHY according to input speed */ 1012 status = hw->phy.ops.setup_link_speed(hw, speed, 1013 autoneg_wait_to_complete); 1014 /* Set up MAC */ 1015 ixgbe_start_mac_link_82599(hw, autoneg_wait_to_complete); 1016 1017 return status; 1018 } 1019 1020 /** 1021 * ixgbe_reset_hw_82599 - Perform hardware reset 1022 * @hw: pointer to hardware structure 1023 * 1024 * Resets the hardware by resetting the transmit and receive units, masks 1025 * and clears all interrupts, perform a PHY reset, and perform a link (MAC) 1026 * reset. 1027 **/ 1028 s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw) 1029 { 1030 ixgbe_link_speed link_speed; 1031 s32 status; 1032 u32 ctrl = 0; 1033 u32 i, autoc, autoc2; 1034 u32 curr_lms; 1035 bool link_up = FALSE; 1036 1037 DEBUGFUNC("ixgbe_reset_hw_82599"); 1038 1039 /* Call adapter stop to disable tx/rx and clear interrupts */ 1040 status = hw->mac.ops.stop_adapter(hw); 1041 if (status != IXGBE_SUCCESS) 1042 goto reset_hw_out; 1043 1044 /* flush pending Tx transactions */ 1045 ixgbe_clear_tx_pending(hw); 1046 1047 /* PHY ops must be identified and initialized prior to reset */ 1048 1049 /* Identify PHY and related function pointers */ 1050 status = hw->phy.ops.init(hw); 1051 1052 if (status == IXGBE_ERR_SFP_NOT_SUPPORTED) 1053 goto reset_hw_out; 1054 1055 /* Setup SFP module if there is one present. */ 1056 if (hw->phy.sfp_setup_needed) { 1057 status = hw->mac.ops.setup_sfp(hw); 1058 hw->phy.sfp_setup_needed = FALSE; 1059 } 1060 1061 if (status == IXGBE_ERR_SFP_NOT_SUPPORTED) 1062 goto reset_hw_out; 1063 1064 /* Reset PHY */ 1065 if (hw->phy.reset_disable == FALSE && hw->phy.ops.reset != NULL) 1066 hw->phy.ops.reset(hw); 1067 1068 /* remember AUTOC from before we reset */ 1069 curr_lms = IXGBE_READ_REG(hw, IXGBE_AUTOC) & IXGBE_AUTOC_LMS_MASK; 1070 1071 mac_reset_top: 1072 /* 1073 * Issue global reset to the MAC. Needs to be SW reset if link is up. 1074 * If link reset is used when link is up, it might reset the PHY when 1075 * mng is using it. If link is down or the flag to force full link 1076 * reset is set, then perform link reset. 1077 */ 1078 ctrl = IXGBE_CTRL_LNK_RST; 1079 if (!hw->force_full_reset) { 1080 hw->mac.ops.check_link(hw, &link_speed, &link_up, FALSE); 1081 if (link_up) 1082 ctrl = IXGBE_CTRL_RST; 1083 } 1084 1085 ctrl |= IXGBE_READ_REG(hw, IXGBE_CTRL); 1086 IXGBE_WRITE_REG(hw, IXGBE_CTRL, ctrl); 1087 IXGBE_WRITE_FLUSH(hw); 1088 1089 /* Poll for reset bit to self-clear meaning reset is complete */ 1090 for (i = 0; i < 10; i++) { 1091 usec_delay(1); 1092 ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL); 1093 if (!(ctrl & IXGBE_CTRL_RST_MASK)) 1094 break; 1095 } 1096 1097 if (ctrl & IXGBE_CTRL_RST_MASK) { 1098 status = IXGBE_ERR_RESET_FAILED; 1099 DEBUGOUT("Reset polling failed to complete.\n"); 1100 } 1101 1102 msec_delay(50); 1103 1104 /* 1105 * Double resets are required for recovery from certain error 1106 * conditions. Between resets, it is necessary to stall to 1107 * allow time for any pending HW events to complete. 1108 */ 1109 if (hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED) { 1110 hw->mac.flags &= ~IXGBE_FLAGS_DOUBLE_RESET_REQUIRED; 1111 goto mac_reset_top; 1112 } 1113 1114 /* 1115 * Store the original AUTOC/AUTOC2 values if they have not been 1116 * stored off yet. Otherwise restore the stored original 1117 * values since the reset operation sets back to defaults. 1118 */ 1119 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); 1120 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2); 1121 1122 /* Enable link if disabled in NVM */ 1123 if (autoc2 & IXGBE_AUTOC2_LINK_DISABLE_MASK) { 1124 autoc2 &= ~IXGBE_AUTOC2_LINK_DISABLE_MASK; 1125 IXGBE_WRITE_REG(hw, IXGBE_AUTOC2, autoc2); 1126 IXGBE_WRITE_FLUSH(hw); 1127 } 1128 1129 if (hw->mac.orig_link_settings_stored == FALSE) { 1130 hw->mac.orig_autoc = autoc; 1131 hw->mac.orig_autoc2 = autoc2; 1132 hw->mac.orig_link_settings_stored = TRUE; 1133 } else { 1134 1135 /* If MNG FW is running on a multi-speed device that 1136 * doesn't autoneg with out driver support we need to 1137 * leave LMS in the state it was before we MAC reset. 1138 * Likewise if we support WoL we don't want change the 1139 * LMS state. 1140 */ 1141 if ((hw->phy.multispeed_fiber && ixgbe_mng_enabled(hw)) || 1142 hw->wol_enabled) 1143 hw->mac.orig_autoc = 1144 (hw->mac.orig_autoc & ~IXGBE_AUTOC_LMS_MASK) | 1145 curr_lms; 1146 1147 if (autoc != hw->mac.orig_autoc) { 1148 status = hw->mac.ops.prot_autoc_write(hw, 1149 hw->mac.orig_autoc, 1150 FALSE); 1151 if (status != IXGBE_SUCCESS) 1152 goto reset_hw_out; 1153 } 1154 1155 if ((autoc2 & IXGBE_AUTOC2_UPPER_MASK) != 1156 (hw->mac.orig_autoc2 & IXGBE_AUTOC2_UPPER_MASK)) { 1157 autoc2 &= ~IXGBE_AUTOC2_UPPER_MASK; 1158 autoc2 |= (hw->mac.orig_autoc2 & 1159 IXGBE_AUTOC2_UPPER_MASK); 1160 IXGBE_WRITE_REG(hw, IXGBE_AUTOC2, autoc2); 1161 } 1162 } 1163 1164 /* Store the permanent mac address */ 1165 hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr); 1166 1167 /* 1168 * Store MAC address from RAR0, clear receive address registers, and 1169 * clear the multicast table. Also reset num_rar_entries to 128, 1170 * since we modify this value when programming the SAN MAC address. 1171 */ 1172 hw->mac.num_rar_entries = 128; 1173 hw->mac.ops.init_rx_addrs(hw); 1174 1175 /* Store the permanent SAN mac address */ 1176 hw->mac.ops.get_san_mac_addr(hw, hw->mac.san_addr); 1177 1178 /* Add the SAN MAC address to the RAR only if it's a valid address */ 1179 if (ixgbe_validate_mac_addr(hw->mac.san_addr) == 0) { 1180 hw->mac.ops.set_rar(hw, hw->mac.num_rar_entries - 1, 1181 hw->mac.san_addr, 0, IXGBE_RAH_AV); 1182 1183 /* Save the SAN MAC RAR index */ 1184 hw->mac.san_mac_rar_index = hw->mac.num_rar_entries - 1; 1185 1186 /* Reserve the last RAR for the SAN MAC address */ 1187 hw->mac.num_rar_entries--; 1188 } 1189 1190 /* Store the alternative WWNN/WWPN prefix */ 1191 hw->mac.ops.get_wwn_prefix(hw, &hw->mac.wwnn_prefix, 1192 &hw->mac.wwpn_prefix); 1193 1194 reset_hw_out: 1195 return status; 1196 } 1197 1198 /** 1199 * ixgbe_fdir_check_cmd_complete - poll to check whether FDIRCMD is complete 1200 * @hw: pointer to hardware structure 1201 * @fdircmd: current value of FDIRCMD register 1202 */ 1203 static s32 ixgbe_fdir_check_cmd_complete(struct ixgbe_hw *hw, u32 *fdircmd) 1204 { 1205 int i; 1206 1207 for (i = 0; i < IXGBE_FDIRCMD_CMD_POLL; i++) { 1208 *fdircmd = IXGBE_READ_REG(hw, IXGBE_FDIRCMD); 1209 if (!(*fdircmd & IXGBE_FDIRCMD_CMD_MASK)) 1210 return IXGBE_SUCCESS; 1211 usec_delay(10); 1212 } 1213 1214 return IXGBE_ERR_FDIR_CMD_INCOMPLETE; 1215 } 1216 1217 /** 1218 * ixgbe_reinit_fdir_tables_82599 - Reinitialize Flow Director tables. 1219 * @hw: pointer to hardware structure 1220 **/ 1221 s32 ixgbe_reinit_fdir_tables_82599(struct ixgbe_hw *hw) 1222 { 1223 s32 err; 1224 int i; 1225 u32 fdirctrl = IXGBE_READ_REG(hw, IXGBE_FDIRCTRL); 1226 u32 fdircmd; 1227 fdirctrl &= ~IXGBE_FDIRCTRL_INIT_DONE; 1228 1229 DEBUGFUNC("ixgbe_reinit_fdir_tables_82599"); 1230 1231 /* 1232 * Before starting reinitialization process, 1233 * FDIRCMD.CMD must be zero. 1234 */ 1235 err = ixgbe_fdir_check_cmd_complete(hw, &fdircmd); 1236 if (err) { 1237 DEBUGOUT("Flow Director previous command did not complete, aborting table re-initialization.\n"); 1238 return err; 1239 } 1240 1241 IXGBE_WRITE_REG(hw, IXGBE_FDIRFREE, 0); 1242 IXGBE_WRITE_FLUSH(hw); 1243 /* 1244 * 82599 adapters flow director init flow cannot be restarted, 1245 * Workaround 82599 silicon errata by performing the following steps 1246 * before re-writing the FDIRCTRL control register with the same value. 1247 * - write 1 to bit 8 of FDIRCMD register & 1248 * - write 0 to bit 8 of FDIRCMD register 1249 */ 1250 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, 1251 (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) | 1252 IXGBE_FDIRCMD_CLEARHT)); 1253 IXGBE_WRITE_FLUSH(hw); 1254 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, 1255 (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) & 1256 ~IXGBE_FDIRCMD_CLEARHT)); 1257 IXGBE_WRITE_FLUSH(hw); 1258 /* 1259 * Clear FDIR Hash register to clear any leftover hashes 1260 * waiting to be programmed. 1261 */ 1262 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, 0x00); 1263 IXGBE_WRITE_FLUSH(hw); 1264 1265 IXGBE_WRITE_REG(hw, IXGBE_FDIRCTRL, fdirctrl); 1266 IXGBE_WRITE_FLUSH(hw); 1267 1268 /* Poll init-done after we write FDIRCTRL register */ 1269 for (i = 0; i < IXGBE_FDIR_INIT_DONE_POLL; i++) { 1270 if (IXGBE_READ_REG(hw, IXGBE_FDIRCTRL) & 1271 IXGBE_FDIRCTRL_INIT_DONE) 1272 break; 1273 msec_delay(1); 1274 } 1275 if (i >= IXGBE_FDIR_INIT_DONE_POLL) { 1276 DEBUGOUT("Flow Director Signature poll time exceeded!\n"); 1277 return IXGBE_ERR_FDIR_REINIT_FAILED; 1278 } 1279 1280 /* Clear FDIR statistics registers (read to clear) */ 1281 IXGBE_READ_REG(hw, IXGBE_FDIRUSTAT); 1282 IXGBE_READ_REG(hw, IXGBE_FDIRFSTAT); 1283 IXGBE_READ_REG(hw, IXGBE_FDIRMATCH); 1284 IXGBE_READ_REG(hw, IXGBE_FDIRMISS); 1285 IXGBE_READ_REG(hw, IXGBE_FDIRLEN); 1286 1287 return IXGBE_SUCCESS; 1288 } 1289 1290 /** 1291 * ixgbe_fdir_enable_82599 - Initialize Flow Director control registers 1292 * @hw: pointer to hardware structure 1293 * @fdirctrl: value to write to flow director control register 1294 **/ 1295 static void ixgbe_fdir_enable_82599(struct ixgbe_hw *hw, u32 fdirctrl) 1296 { 1297 int i; 1298 1299 DEBUGFUNC("ixgbe_fdir_enable_82599"); 1300 1301 /* Prime the keys for hashing */ 1302 IXGBE_WRITE_REG(hw, IXGBE_FDIRHKEY, IXGBE_ATR_BUCKET_HASH_KEY); 1303 IXGBE_WRITE_REG(hw, IXGBE_FDIRSKEY, IXGBE_ATR_SIGNATURE_HASH_KEY); 1304 1305 /* 1306 * Poll init-done after we write the register. Estimated times: 1307 * 10G: PBALLOC = 11b, timing is 60us 1308 * 1G: PBALLOC = 11b, timing is 600us 1309 * 100M: PBALLOC = 11b, timing is 6ms 1310 * 1311 * Multiple these timings by 4 if under full Rx load 1312 * 1313 * So we'll poll for IXGBE_FDIR_INIT_DONE_POLL times, sleeping for 1314 * 1 msec per poll time. If we're at line rate and drop to 100M, then 1315 * this might not finish in our poll time, but we can live with that 1316 * for now. 1317 */ 1318 IXGBE_WRITE_REG(hw, IXGBE_FDIRCTRL, fdirctrl); 1319 IXGBE_WRITE_FLUSH(hw); 1320 for (i = 0; i < IXGBE_FDIR_INIT_DONE_POLL; i++) { 1321 if (IXGBE_READ_REG(hw, IXGBE_FDIRCTRL) & 1322 IXGBE_FDIRCTRL_INIT_DONE) 1323 break; 1324 msec_delay(1); 1325 } 1326 1327 if (i >= IXGBE_FDIR_INIT_DONE_POLL) 1328 DEBUGOUT("Flow Director poll time exceeded!\n"); 1329 } 1330 1331 /** 1332 * ixgbe_init_fdir_signature_82599 - Initialize Flow Director signature filters 1333 * @hw: pointer to hardware structure 1334 * @fdirctrl: value to write to flow director control register, initially 1335 * contains just the value of the Rx packet buffer allocation 1336 **/ 1337 s32 ixgbe_init_fdir_signature_82599(struct ixgbe_hw *hw, u32 fdirctrl) 1338 { 1339 DEBUGFUNC("ixgbe_init_fdir_signature_82599"); 1340 1341 /* 1342 * Continue setup of fdirctrl register bits: 1343 * Move the flexible bytes to use the ethertype - shift 6 words 1344 * Set the maximum length per hash bucket to 0xA filters 1345 * Send interrupt when 64 filters are left 1346 */ 1347 fdirctrl |= (0x6 << IXGBE_FDIRCTRL_FLEX_SHIFT) | 1348 (0xA << IXGBE_FDIRCTRL_MAX_LENGTH_SHIFT) | 1349 (4 << IXGBE_FDIRCTRL_FULL_THRESH_SHIFT); 1350 1351 /* write hashes and fdirctrl register, poll for completion */ 1352 ixgbe_fdir_enable_82599(hw, fdirctrl); 1353 1354 return IXGBE_SUCCESS; 1355 } 1356 1357 /** 1358 * ixgbe_init_fdir_perfect_82599 - Initialize Flow Director perfect filters 1359 * @hw: pointer to hardware structure 1360 * @fdirctrl: value to write to flow director control register, initially 1361 * contains just the value of the Rx packet buffer allocation 1362 * @cloud_mode: TRUE - cloud mode, FALSE - other mode 1363 **/ 1364 s32 ixgbe_init_fdir_perfect_82599(struct ixgbe_hw *hw, u32 fdirctrl, 1365 bool cloud_mode) 1366 { 1367 DEBUGFUNC("ixgbe_init_fdir_perfect_82599"); 1368 1369 /* 1370 * Continue setup of fdirctrl register bits: 1371 * Turn perfect match filtering on 1372 * Report hash in RSS field of Rx wb descriptor 1373 * Initialize the drop queue 1374 * Move the flexible bytes to use the ethertype - shift 6 words 1375 * Set the maximum length per hash bucket to 0xA filters 1376 * Send interrupt when 64 (0x4 * 16) filters are left 1377 */ 1378 fdirctrl |= IXGBE_FDIRCTRL_PERFECT_MATCH | 1379 IXGBE_FDIRCTRL_REPORT_STATUS | 1380 (IXGBE_FDIR_DROP_QUEUE << IXGBE_FDIRCTRL_DROP_Q_SHIFT) | 1381 (0x6 << IXGBE_FDIRCTRL_FLEX_SHIFT) | 1382 (0xA << IXGBE_FDIRCTRL_MAX_LENGTH_SHIFT) | 1383 (4 << IXGBE_FDIRCTRL_FULL_THRESH_SHIFT); 1384 1385 if (cloud_mode) 1386 fdirctrl |=(IXGBE_FDIRCTRL_FILTERMODE_CLOUD << 1387 IXGBE_FDIRCTRL_FILTERMODE_SHIFT); 1388 1389 /* write hashes and fdirctrl register, poll for completion */ 1390 ixgbe_fdir_enable_82599(hw, fdirctrl); 1391 1392 return IXGBE_SUCCESS; 1393 } 1394 1395 /* 1396 * These defines allow us to quickly generate all of the necessary instructions 1397 * in the function below by simply calling out IXGBE_COMPUTE_SIG_HASH_ITERATION 1398 * for values 0 through 15 1399 */ 1400 #define IXGBE_ATR_COMMON_HASH_KEY \ 1401 (IXGBE_ATR_BUCKET_HASH_KEY & IXGBE_ATR_SIGNATURE_HASH_KEY) 1402 #define IXGBE_COMPUTE_SIG_HASH_ITERATION(_n) \ 1403 do { \ 1404 u32 n = (_n); \ 1405 if (IXGBE_ATR_COMMON_HASH_KEY & (0x01 << n)) \ 1406 common_hash ^= lo_hash_dword >> n; \ 1407 else if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << n)) \ 1408 bucket_hash ^= lo_hash_dword >> n; \ 1409 else if (IXGBE_ATR_SIGNATURE_HASH_KEY & (0x01 << n)) \ 1410 sig_hash ^= lo_hash_dword << (16 - n); \ 1411 if (IXGBE_ATR_COMMON_HASH_KEY & (0x01 << (n + 16))) \ 1412 common_hash ^= hi_hash_dword >> n; \ 1413 else if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << (n + 16))) \ 1414 bucket_hash ^= hi_hash_dword >> n; \ 1415 else if (IXGBE_ATR_SIGNATURE_HASH_KEY & (0x01 << (n + 16))) \ 1416 sig_hash ^= hi_hash_dword << (16 - n); \ 1417 } while (0) 1418 1419 /** 1420 * ixgbe_atr_compute_sig_hash_82599 - Compute the signature hash 1421 * @stream: input bitstream to compute the hash on 1422 * 1423 * This function is almost identical to the function above but contains 1424 * several optimizations such as unwinding all of the loops, letting the 1425 * compiler work out all of the conditional ifs since the keys are static 1426 * defines, and computing two keys at once since the hashed dword stream 1427 * will be the same for both keys. 1428 **/ 1429 u32 ixgbe_atr_compute_sig_hash_82599(union ixgbe_atr_hash_dword input, 1430 union ixgbe_atr_hash_dword common) 1431 { 1432 u32 hi_hash_dword, lo_hash_dword, flow_vm_vlan; 1433 u32 sig_hash = 0, bucket_hash = 0, common_hash = 0; 1434 1435 /* record the flow_vm_vlan bits as they are a key part to the hash */ 1436 flow_vm_vlan = IXGBE_NTOHL(input.dword); 1437 1438 /* generate common hash dword */ 1439 hi_hash_dword = IXGBE_NTOHL(common.dword); 1440 1441 /* low dword is word swapped version of common */ 1442 lo_hash_dword = (hi_hash_dword >> 16) | (hi_hash_dword << 16); 1443 1444 /* apply flow ID/VM pool/VLAN ID bits to hash words */ 1445 hi_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan >> 16); 1446 1447 /* Process bits 0 and 16 */ 1448 IXGBE_COMPUTE_SIG_HASH_ITERATION(0); 1449 1450 /* 1451 * apply flow ID/VM pool/VLAN ID bits to lo hash dword, we had to 1452 * delay this because bit 0 of the stream should not be processed 1453 * so we do not add the VLAN until after bit 0 was processed 1454 */ 1455 lo_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan << 16); 1456 1457 /* Process remaining 30 bit of the key */ 1458 IXGBE_COMPUTE_SIG_HASH_ITERATION(1); 1459 IXGBE_COMPUTE_SIG_HASH_ITERATION(2); 1460 IXGBE_COMPUTE_SIG_HASH_ITERATION(3); 1461 IXGBE_COMPUTE_SIG_HASH_ITERATION(4); 1462 IXGBE_COMPUTE_SIG_HASH_ITERATION(5); 1463 IXGBE_COMPUTE_SIG_HASH_ITERATION(6); 1464 IXGBE_COMPUTE_SIG_HASH_ITERATION(7); 1465 IXGBE_COMPUTE_SIG_HASH_ITERATION(8); 1466 IXGBE_COMPUTE_SIG_HASH_ITERATION(9); 1467 IXGBE_COMPUTE_SIG_HASH_ITERATION(10); 1468 IXGBE_COMPUTE_SIG_HASH_ITERATION(11); 1469 IXGBE_COMPUTE_SIG_HASH_ITERATION(12); 1470 IXGBE_COMPUTE_SIG_HASH_ITERATION(13); 1471 IXGBE_COMPUTE_SIG_HASH_ITERATION(14); 1472 IXGBE_COMPUTE_SIG_HASH_ITERATION(15); 1473 1474 /* combine common_hash result with signature and bucket hashes */ 1475 bucket_hash ^= common_hash; 1476 bucket_hash &= IXGBE_ATR_HASH_MASK; 1477 1478 sig_hash ^= common_hash << 16; 1479 sig_hash &= IXGBE_ATR_HASH_MASK << 16; 1480 1481 /* return completed signature hash */ 1482 return sig_hash ^ bucket_hash; 1483 } 1484 1485 /** 1486 * ixgbe_atr_add_signature_filter_82599 - Adds a signature hash filter 1487 * @hw: pointer to hardware structure 1488 * @input: unique input dword 1489 * @common: compressed common input dword 1490 * @queue: queue index to direct traffic to 1491 * 1492 * Note that the tunnel bit in input must not be set when the hardware 1493 * tunneling support does not exist. 1494 **/ 1495 s32 ixgbe_fdir_add_signature_filter_82599(struct ixgbe_hw *hw, 1496 union ixgbe_atr_hash_dword input, 1497 union ixgbe_atr_hash_dword common, 1498 u8 queue) 1499 { 1500 u64 fdirhashcmd; 1501 u8 flow_type; 1502 bool tunnel; 1503 u32 fdircmd; 1504 s32 err; 1505 1506 DEBUGFUNC("ixgbe_fdir_add_signature_filter_82599"); 1507 1508 /* 1509 * Get the flow_type in order to program FDIRCMD properly 1510 * lowest 2 bits are FDIRCMD.L4TYPE, third lowest bit is FDIRCMD.IPV6 1511 * fifth is FDIRCMD.TUNNEL_FILTER 1512 */ 1513 tunnel = !!(input.formatted.flow_type & IXGBE_ATR_L4TYPE_TUNNEL_MASK); 1514 flow_type = input.formatted.flow_type & 1515 (IXGBE_ATR_L4TYPE_TUNNEL_MASK - 1); 1516 switch (flow_type) { 1517 case IXGBE_ATR_FLOW_TYPE_TCPV4: 1518 case IXGBE_ATR_FLOW_TYPE_UDPV4: 1519 case IXGBE_ATR_FLOW_TYPE_SCTPV4: 1520 case IXGBE_ATR_FLOW_TYPE_TCPV6: 1521 case IXGBE_ATR_FLOW_TYPE_UDPV6: 1522 case IXGBE_ATR_FLOW_TYPE_SCTPV6: 1523 break; 1524 default: 1525 DEBUGOUT(" Error on flow type input\n"); 1526 return IXGBE_ERR_CONFIG; 1527 } 1528 1529 /* configure FDIRCMD register */ 1530 fdircmd = IXGBE_FDIRCMD_CMD_ADD_FLOW | IXGBE_FDIRCMD_FILTER_UPDATE | 1531 IXGBE_FDIRCMD_LAST | IXGBE_FDIRCMD_QUEUE_EN; 1532 fdircmd |= (u32)flow_type << IXGBE_FDIRCMD_FLOW_TYPE_SHIFT; 1533 fdircmd |= (u32)queue << IXGBE_FDIRCMD_RX_QUEUE_SHIFT; 1534 if (tunnel) 1535 fdircmd |= IXGBE_FDIRCMD_TUNNEL_FILTER; 1536 1537 /* 1538 * The lower 32-bits of fdirhashcmd is for FDIRHASH, the upper 32-bits 1539 * is for FDIRCMD. Then do a 64-bit register write from FDIRHASH. 1540 */ 1541 fdirhashcmd = (u64)fdircmd << 32; 1542 fdirhashcmd |= ixgbe_atr_compute_sig_hash_82599(input, common); 1543 IXGBE_WRITE_REG64(hw, IXGBE_FDIRHASH, fdirhashcmd); 1544 1545 err = ixgbe_fdir_check_cmd_complete(hw, &fdircmd); 1546 if (err) { 1547 DEBUGOUT("Flow Director command did not complete!\n"); 1548 return err; 1549 } 1550 1551 DEBUGOUT2("Tx Queue=%x hash=%x\n", queue, (u32)fdirhashcmd); 1552 1553 return IXGBE_SUCCESS; 1554 } 1555 1556 #define IXGBE_COMPUTE_BKT_HASH_ITERATION(_n) \ 1557 do { \ 1558 u32 n = (_n); \ 1559 if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << n)) \ 1560 bucket_hash ^= lo_hash_dword >> n; \ 1561 if (IXGBE_ATR_BUCKET_HASH_KEY & (0x01 << (n + 16))) \ 1562 bucket_hash ^= hi_hash_dword >> n; \ 1563 } while (0) 1564 1565 /** 1566 * ixgbe_atr_compute_perfect_hash_82599 - Compute the perfect filter hash 1567 * @atr_input: input bitstream to compute the hash on 1568 * @input_mask: mask for the input bitstream 1569 * 1570 * This function serves two main purposes. First it applies the input_mask 1571 * to the atr_input resulting in a cleaned up atr_input data stream. 1572 * Secondly it computes the hash and stores it in the bkt_hash field at 1573 * the end of the input byte stream. This way it will be available for 1574 * future use without needing to recompute the hash. 1575 **/ 1576 void ixgbe_atr_compute_perfect_hash_82599(union ixgbe_atr_input *input, 1577 union ixgbe_atr_input *input_mask) 1578 { 1579 1580 u32 hi_hash_dword, lo_hash_dword, flow_vm_vlan; 1581 u32 bucket_hash = 0; 1582 u32 hi_dword = 0; 1583 u32 i = 0; 1584 1585 /* Apply masks to input data */ 1586 for (i = 0; i < 14; i++) 1587 input->dword_stream[i] &= input_mask->dword_stream[i]; 1588 1589 /* record the flow_vm_vlan bits as they are a key part to the hash */ 1590 flow_vm_vlan = IXGBE_NTOHL(input->dword_stream[0]); 1591 1592 /* generate common hash dword */ 1593 for (i = 1; i <= 13; i++) 1594 hi_dword ^= input->dword_stream[i]; 1595 hi_hash_dword = IXGBE_NTOHL(hi_dword); 1596 1597 /* low dword is word swapped version of common */ 1598 lo_hash_dword = (hi_hash_dword >> 16) | (hi_hash_dword << 16); 1599 1600 /* apply flow ID/VM pool/VLAN ID bits to hash words */ 1601 hi_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan >> 16); 1602 1603 /* Process bits 0 and 16 */ 1604 IXGBE_COMPUTE_BKT_HASH_ITERATION(0); 1605 1606 /* 1607 * apply flow ID/VM pool/VLAN ID bits to lo hash dword, we had to 1608 * delay this because bit 0 of the stream should not be processed 1609 * so we do not add the VLAN until after bit 0 was processed 1610 */ 1611 lo_hash_dword ^= flow_vm_vlan ^ (flow_vm_vlan << 16); 1612 1613 /* Process remaining 30 bit of the key */ 1614 for (i = 1; i <= 15; i++) 1615 IXGBE_COMPUTE_BKT_HASH_ITERATION(i); 1616 1617 /* 1618 * Limit hash to 13 bits since max bucket count is 8K. 1619 * Store result at the end of the input stream. 1620 */ 1621 input->formatted.bkt_hash = bucket_hash & 0x1FFF; 1622 } 1623 1624 /** 1625 * ixgbe_get_fdirtcpm_82599 - generate a TCP port from atr_input_masks 1626 * @input_mask: mask to be bit swapped 1627 * 1628 * The source and destination port masks for flow director are bit swapped 1629 * in that bit 15 effects bit 0, 14 effects 1, 13, 2 etc. In order to 1630 * generate a correctly swapped value we need to bit swap the mask and that 1631 * is what is accomplished by this function. 1632 **/ 1633 static u32 ixgbe_get_fdirtcpm_82599(union ixgbe_atr_input *input_mask) 1634 { 1635 u32 mask = IXGBE_NTOHS(input_mask->formatted.dst_port); 1636 mask <<= IXGBE_FDIRTCPM_DPORTM_SHIFT; 1637 mask |= IXGBE_NTOHS(input_mask->formatted.src_port); 1638 mask = ((mask & 0x55555555) << 1) | ((mask & 0xAAAAAAAA) >> 1); 1639 mask = ((mask & 0x33333333) << 2) | ((mask & 0xCCCCCCCC) >> 2); 1640 mask = ((mask & 0x0F0F0F0F) << 4) | ((mask & 0xF0F0F0F0) >> 4); 1641 return ((mask & 0x00FF00FF) << 8) | ((mask & 0xFF00FF00) >> 8); 1642 } 1643 1644 /* 1645 * These two macros are meant to address the fact that we have registers 1646 * that are either all or in part big-endian. As a result on big-endian 1647 * systems we will end up byte swapping the value to little-endian before 1648 * it is byte swapped again and written to the hardware in the original 1649 * big-endian format. 1650 */ 1651 #define IXGBE_STORE_AS_BE32(_value) \ 1652 (((u32)(_value) >> 24) | (((u32)(_value) & 0x00FF0000) >> 8) | \ 1653 (((u32)(_value) & 0x0000FF00) << 8) | ((u32)(_value) << 24)) 1654 1655 #define IXGBE_WRITE_REG_BE32(a, reg, value) \ 1656 IXGBE_WRITE_REG((a), (reg), IXGBE_STORE_AS_BE32(IXGBE_NTOHL(value))) 1657 1658 #define IXGBE_STORE_AS_BE16(_value) \ 1659 IXGBE_NTOHS(((u16)(_value) >> 8) | ((u16)(_value) << 8)) 1660 1661 s32 ixgbe_fdir_set_input_mask_82599(struct ixgbe_hw *hw, 1662 union ixgbe_atr_input *input_mask, bool cloud_mode) 1663 { 1664 /* mask IPv6 since it is currently not supported */ 1665 u32 fdirm = IXGBE_FDIRM_DIPv6; 1666 u32 fdirtcpm; 1667 u32 fdirip6m; 1668 DEBUGFUNC("ixgbe_fdir_set_atr_input_mask_82599"); 1669 1670 /* 1671 * Program the relevant mask registers. If src/dst_port or src/dst_addr 1672 * are zero, then assume a full mask for that field. Also assume that 1673 * a VLAN of 0 is unspecified, so mask that out as well. L4type 1674 * cannot be masked out in this implementation. 1675 * 1676 * This also assumes IPv4 only. IPv6 masking isn't supported at this 1677 * point in time. 1678 */ 1679 1680 /* verify bucket hash is cleared on hash generation */ 1681 if (input_mask->formatted.bkt_hash) 1682 DEBUGOUT(" bucket hash should always be 0 in mask\n"); 1683 1684 /* Program FDIRM and verify partial masks */ 1685 switch (input_mask->formatted.vm_pool & 0x7F) { 1686 case 0x0: 1687 fdirm |= IXGBE_FDIRM_POOL; 1688 case 0x7F: 1689 break; 1690 default: 1691 DEBUGOUT(" Error on vm pool mask\n"); 1692 return IXGBE_ERR_CONFIG; 1693 } 1694 1695 switch (input_mask->formatted.flow_type & IXGBE_ATR_L4TYPE_MASK) { 1696 case 0x0: 1697 fdirm |= IXGBE_FDIRM_L4P; 1698 if (input_mask->formatted.dst_port || 1699 input_mask->formatted.src_port) { 1700 DEBUGOUT(" Error on src/dst port mask\n"); 1701 return IXGBE_ERR_CONFIG; 1702 } 1703 case IXGBE_ATR_L4TYPE_MASK: 1704 break; 1705 default: 1706 DEBUGOUT(" Error on flow type mask\n"); 1707 return IXGBE_ERR_CONFIG; 1708 } 1709 1710 switch (IXGBE_NTOHS(input_mask->formatted.vlan_id) & 0xEFFF) { 1711 case 0x0000: 1712 /* mask VLAN ID, fall through to mask VLAN priority */ 1713 fdirm |= IXGBE_FDIRM_VLANID; 1714 case 0x0FFF: 1715 /* mask VLAN priority */ 1716 fdirm |= IXGBE_FDIRM_VLANP; 1717 break; 1718 case 0xE000: 1719 /* mask VLAN ID only, fall through */ 1720 fdirm |= IXGBE_FDIRM_VLANID; 1721 case 0xEFFF: 1722 /* no VLAN fields masked */ 1723 break; 1724 default: 1725 DEBUGOUT(" Error on VLAN mask\n"); 1726 return IXGBE_ERR_CONFIG; 1727 } 1728 1729 switch (input_mask->formatted.flex_bytes & 0xFFFF) { 1730 case 0x0000: 1731 /* Mask Flex Bytes, fall through */ 1732 fdirm |= IXGBE_FDIRM_FLEX; 1733 case 0xFFFF: 1734 break; 1735 default: 1736 DEBUGOUT(" Error on flexible byte mask\n"); 1737 return IXGBE_ERR_CONFIG; 1738 } 1739 1740 if (cloud_mode) { 1741 fdirm |= IXGBE_FDIRM_L3P; 1742 fdirip6m = ((u32) 0xFFFFU << IXGBE_FDIRIP6M_DIPM_SHIFT); 1743 fdirip6m |= IXGBE_FDIRIP6M_ALWAYS_MASK; 1744 1745 switch (input_mask->formatted.inner_mac[0] & 0xFF) { 1746 case 0x00: 1747 /* Mask inner MAC, fall through */ 1748 fdirip6m |= IXGBE_FDIRIP6M_INNER_MAC; 1749 case 0xFF: 1750 break; 1751 default: 1752 DEBUGOUT(" Error on inner_mac byte mask\n"); 1753 return IXGBE_ERR_CONFIG; 1754 } 1755 1756 switch (input_mask->formatted.tni_vni & 0xFFFFFFFF) { 1757 case 0x0: 1758 /* Mask vxlan id */ 1759 fdirip6m |= IXGBE_FDIRIP6M_TNI_VNI; 1760 break; 1761 case 0x00FFFFFF: 1762 fdirip6m |= IXGBE_FDIRIP6M_TNI_VNI_24; 1763 break; 1764 case 0xFFFFFFFF: 1765 break; 1766 default: 1767 DEBUGOUT(" Error on TNI/VNI byte mask\n"); 1768 return IXGBE_ERR_CONFIG; 1769 } 1770 1771 switch (input_mask->formatted.tunnel_type & 0xFFFF) { 1772 case 0x0: 1773 /* Mask turnnel type, fall through */ 1774 fdirip6m |= IXGBE_FDIRIP6M_TUNNEL_TYPE; 1775 case 0xFFFF: 1776 break; 1777 default: 1778 DEBUGOUT(" Error on tunnel type byte mask\n"); 1779 return IXGBE_ERR_CONFIG; 1780 } 1781 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRIP6M, fdirip6m); 1782 1783 /* Set all bits in FDIRTCPM, FDIRUDPM, FDIRSIP4M and 1784 * FDIRDIP4M in cloud mode to allow L3/L3 packets to 1785 * tunnel. 1786 */ 1787 IXGBE_WRITE_REG(hw, IXGBE_FDIRTCPM, 0xFFFFFFFF); 1788 IXGBE_WRITE_REG(hw, IXGBE_FDIRUDPM, 0xFFFFFFFF); 1789 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRDIP4M, 0xFFFFFFFF); 1790 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIP4M, 0xFFFFFFFF); 1791 } 1792 1793 /* Now mask VM pool and destination IPv6 - bits 5 and 2 */ 1794 IXGBE_WRITE_REG(hw, IXGBE_FDIRM, fdirm); 1795 1796 if (!cloud_mode) { 1797 /* store the TCP/UDP port masks, bit reversed from port 1798 * layout */ 1799 fdirtcpm = ixgbe_get_fdirtcpm_82599(input_mask); 1800 1801 /* write both the same so that UDP and TCP use the same mask */ 1802 IXGBE_WRITE_REG(hw, IXGBE_FDIRTCPM, ~fdirtcpm); 1803 IXGBE_WRITE_REG(hw, IXGBE_FDIRUDPM, ~fdirtcpm); 1804 /* also use it for SCTP */ 1805 switch (hw->mac.type) { 1806 case ixgbe_mac_X550: 1807 case ixgbe_mac_X550EM_x: 1808 case ixgbe_mac_X550EM_a: 1809 IXGBE_WRITE_REG(hw, IXGBE_FDIRSCTPM, ~fdirtcpm); 1810 break; 1811 default: 1812 break; 1813 } 1814 1815 /* store source and destination IP masks (big-enian) */ 1816 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIP4M, 1817 ~input_mask->formatted.src_ip[0]); 1818 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRDIP4M, 1819 ~input_mask->formatted.dst_ip[0]); 1820 } 1821 return IXGBE_SUCCESS; 1822 } 1823 1824 s32 ixgbe_fdir_write_perfect_filter_82599(struct ixgbe_hw *hw, 1825 union ixgbe_atr_input *input, 1826 u16 soft_id, u8 queue, bool cloud_mode) 1827 { 1828 u32 fdirport, fdirvlan, fdirhash, fdircmd; 1829 u32 addr_low, addr_high; 1830 u32 cloud_type = 0; 1831 s32 err; 1832 1833 DEBUGFUNC("ixgbe_fdir_write_perfect_filter_82599"); 1834 if (!cloud_mode) { 1835 /* currently IPv6 is not supported, must be programmed with 0 */ 1836 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(0), 1837 input->formatted.src_ip[0]); 1838 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(1), 1839 input->formatted.src_ip[1]); 1840 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(2), 1841 input->formatted.src_ip[2]); 1842 1843 /* record the source address (big-endian) */ 1844 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRIPSA, 1845 input->formatted.src_ip[0]); 1846 1847 /* record the first 32 bits of the destination address 1848 * (big-endian) */ 1849 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRIPDA, 1850 input->formatted.dst_ip[0]); 1851 1852 /* record source and destination port (little-endian)*/ 1853 fdirport = IXGBE_NTOHS(input->formatted.dst_port); 1854 fdirport <<= IXGBE_FDIRPORT_DESTINATION_SHIFT; 1855 fdirport |= IXGBE_NTOHS(input->formatted.src_port); 1856 IXGBE_WRITE_REG(hw, IXGBE_FDIRPORT, fdirport); 1857 } 1858 1859 /* record VLAN (little-endian) and flex_bytes(big-endian) */ 1860 fdirvlan = IXGBE_STORE_AS_BE16(input->formatted.flex_bytes); 1861 fdirvlan <<= IXGBE_FDIRVLAN_FLEX_SHIFT; 1862 fdirvlan |= IXGBE_NTOHS(input->formatted.vlan_id); 1863 IXGBE_WRITE_REG(hw, IXGBE_FDIRVLAN, fdirvlan); 1864 1865 if (cloud_mode) { 1866 if (input->formatted.tunnel_type != 0) 1867 cloud_type = 0x80000000; 1868 1869 addr_low = ((u32)input->formatted.inner_mac[0] | 1870 ((u32)input->formatted.inner_mac[1] << 8) | 1871 ((u32)input->formatted.inner_mac[2] << 16) | 1872 ((u32)input->formatted.inner_mac[3] << 24)); 1873 addr_high = ((u32)input->formatted.inner_mac[4] | 1874 ((u32)input->formatted.inner_mac[5] << 8)); 1875 cloud_type |= addr_high; 1876 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(0), addr_low); 1877 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(1), cloud_type); 1878 IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIPv6(2), input->formatted.tni_vni); 1879 } 1880 1881 /* configure FDIRHASH register */ 1882 fdirhash = input->formatted.bkt_hash; 1883 fdirhash |= soft_id << IXGBE_FDIRHASH_SIG_SW_INDEX_SHIFT; 1884 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash); 1885 1886 /* 1887 * flush all previous writes to make certain registers are 1888 * programmed prior to issuing the command 1889 */ 1890 IXGBE_WRITE_FLUSH(hw); 1891 1892 /* configure FDIRCMD register */ 1893 fdircmd = IXGBE_FDIRCMD_CMD_ADD_FLOW | IXGBE_FDIRCMD_FILTER_UPDATE | 1894 IXGBE_FDIRCMD_LAST | IXGBE_FDIRCMD_QUEUE_EN; 1895 if (queue == IXGBE_FDIR_DROP_QUEUE) 1896 fdircmd |= IXGBE_FDIRCMD_DROP; 1897 if (input->formatted.flow_type & IXGBE_ATR_L4TYPE_TUNNEL_MASK) 1898 fdircmd |= IXGBE_FDIRCMD_TUNNEL_FILTER; 1899 fdircmd |= input->formatted.flow_type << IXGBE_FDIRCMD_FLOW_TYPE_SHIFT; 1900 fdircmd |= (u32)queue << IXGBE_FDIRCMD_RX_QUEUE_SHIFT; 1901 fdircmd |= (u32)input->formatted.vm_pool << IXGBE_FDIRCMD_VT_POOL_SHIFT; 1902 1903 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, fdircmd); 1904 err = ixgbe_fdir_check_cmd_complete(hw, &fdircmd); 1905 if (err) { 1906 DEBUGOUT("Flow Director command did not complete!\n"); 1907 return err; 1908 } 1909 1910 return IXGBE_SUCCESS; 1911 } 1912 1913 s32 ixgbe_fdir_erase_perfect_filter_82599(struct ixgbe_hw *hw, 1914 union ixgbe_atr_input *input, 1915 u16 soft_id) 1916 { 1917 u32 fdirhash; 1918 u32 fdircmd; 1919 s32 err; 1920 1921 /* configure FDIRHASH register */ 1922 fdirhash = input->formatted.bkt_hash; 1923 fdirhash |= soft_id << IXGBE_FDIRHASH_SIG_SW_INDEX_SHIFT; 1924 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash); 1925 1926 /* flush hash to HW */ 1927 IXGBE_WRITE_FLUSH(hw); 1928 1929 /* Query if filter is present */ 1930 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, IXGBE_FDIRCMD_CMD_QUERY_REM_FILT); 1931 1932 err = ixgbe_fdir_check_cmd_complete(hw, &fdircmd); 1933 if (err) { 1934 DEBUGOUT("Flow Director command did not complete!\n"); 1935 return err; 1936 } 1937 1938 /* if filter exists in hardware then remove it */ 1939 if (fdircmd & IXGBE_FDIRCMD_FILTER_VALID) { 1940 IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash); 1941 IXGBE_WRITE_FLUSH(hw); 1942 IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, 1943 IXGBE_FDIRCMD_CMD_REMOVE_FLOW); 1944 } 1945 1946 return IXGBE_SUCCESS; 1947 } 1948 1949 /** 1950 * ixgbe_fdir_add_perfect_filter_82599 - Adds a perfect filter 1951 * @hw: pointer to hardware structure 1952 * @input: input bitstream 1953 * @input_mask: mask for the input bitstream 1954 * @soft_id: software index for the filters 1955 * @queue: queue index to direct traffic to 1956 * 1957 * Note that the caller to this function must lock before calling, since the 1958 * hardware writes must be protected from one another. 1959 **/ 1960 s32 ixgbe_fdir_add_perfect_filter_82599(struct ixgbe_hw *hw, 1961 union ixgbe_atr_input *input, 1962 union ixgbe_atr_input *input_mask, 1963 u16 soft_id, u8 queue, bool cloud_mode) 1964 { 1965 s32 err = IXGBE_ERR_CONFIG; 1966 1967 DEBUGFUNC("ixgbe_fdir_add_perfect_filter_82599"); 1968 1969 /* 1970 * Check flow_type formatting, and bail out before we touch the hardware 1971 * if there's a configuration issue 1972 */ 1973 switch (input->formatted.flow_type) { 1974 case IXGBE_ATR_FLOW_TYPE_IPV4: 1975 case IXGBE_ATR_FLOW_TYPE_TUNNELED_IPV4: 1976 input_mask->formatted.flow_type = IXGBE_ATR_L4TYPE_IPV6_MASK; 1977 if (input->formatted.dst_port || input->formatted.src_port) { 1978 DEBUGOUT(" Error on src/dst port\n"); 1979 return IXGBE_ERR_CONFIG; 1980 } 1981 break; 1982 case IXGBE_ATR_FLOW_TYPE_SCTPV4: 1983 case IXGBE_ATR_FLOW_TYPE_TUNNELED_SCTPV4: 1984 if (input->formatted.dst_port || input->formatted.src_port) { 1985 DEBUGOUT(" Error on src/dst port\n"); 1986 return IXGBE_ERR_CONFIG; 1987 } 1988 case IXGBE_ATR_FLOW_TYPE_TCPV4: 1989 case IXGBE_ATR_FLOW_TYPE_TUNNELED_TCPV4: 1990 case IXGBE_ATR_FLOW_TYPE_UDPV4: 1991 case IXGBE_ATR_FLOW_TYPE_TUNNELED_UDPV4: 1992 input_mask->formatted.flow_type = IXGBE_ATR_L4TYPE_IPV6_MASK | 1993 IXGBE_ATR_L4TYPE_MASK; 1994 break; 1995 default: 1996 DEBUGOUT(" Error on flow type input\n"); 1997 return err; 1998 } 1999 2000 /* program input mask into the HW */ 2001 err = ixgbe_fdir_set_input_mask_82599(hw, input_mask, cloud_mode); 2002 if (err) 2003 return err; 2004 2005 /* apply mask and compute/store hash */ 2006 ixgbe_atr_compute_perfect_hash_82599(input, input_mask); 2007 2008 /* program filters to filter memory */ 2009 return ixgbe_fdir_write_perfect_filter_82599(hw, input, 2010 soft_id, queue, cloud_mode); 2011 } 2012 2013 /** 2014 * ixgbe_read_analog_reg8_82599 - Reads 8 bit Omer analog register 2015 * @hw: pointer to hardware structure 2016 * @reg: analog register to read 2017 * @val: read value 2018 * 2019 * Performs read operation to Omer analog register specified. 2020 **/ 2021 s32 ixgbe_read_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 *val) 2022 { 2023 u32 core_ctl; 2024 2025 DEBUGFUNC("ixgbe_read_analog_reg8_82599"); 2026 2027 IXGBE_WRITE_REG(hw, IXGBE_CORECTL, IXGBE_CORECTL_WRITE_CMD | 2028 (reg << 8)); 2029 IXGBE_WRITE_FLUSH(hw); 2030 usec_delay(10); 2031 core_ctl = IXGBE_READ_REG(hw, IXGBE_CORECTL); 2032 *val = (u8)core_ctl; 2033 2034 return IXGBE_SUCCESS; 2035 } 2036 2037 /** 2038 * ixgbe_write_analog_reg8_82599 - Writes 8 bit Omer analog register 2039 * @hw: pointer to hardware structure 2040 * @reg: atlas register to write 2041 * @val: value to write 2042 * 2043 * Performs write operation to Omer analog register specified. 2044 **/ 2045 s32 ixgbe_write_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 val) 2046 { 2047 u32 core_ctl; 2048 2049 DEBUGFUNC("ixgbe_write_analog_reg8_82599"); 2050 2051 core_ctl = (reg << 8) | val; 2052 IXGBE_WRITE_REG(hw, IXGBE_CORECTL, core_ctl); 2053 IXGBE_WRITE_FLUSH(hw); 2054 usec_delay(10); 2055 2056 return IXGBE_SUCCESS; 2057 } 2058 2059 /** 2060 * ixgbe_start_hw_82599 - Prepare hardware for Tx/Rx 2061 * @hw: pointer to hardware structure 2062 * 2063 * Starts the hardware using the generic start_hw function 2064 * and the generation start_hw function. 2065 * Then performs revision-specific operations, if any. 2066 **/ 2067 s32 ixgbe_start_hw_82599(struct ixgbe_hw *hw) 2068 { 2069 s32 ret_val = IXGBE_SUCCESS; 2070 2071 DEBUGFUNC("ixgbe_start_hw_82599"); 2072 2073 ret_val = ixgbe_start_hw_generic(hw); 2074 if (ret_val != IXGBE_SUCCESS) 2075 goto out; 2076 2077 ret_val = ixgbe_start_hw_gen2(hw); 2078 if (ret_val != IXGBE_SUCCESS) 2079 goto out; 2080 2081 /* We need to run link autotry after the driver loads */ 2082 hw->mac.autotry_restart = TRUE; 2083 2084 if (ret_val == IXGBE_SUCCESS) 2085 ret_val = ixgbe_verify_fw_version_82599(hw); 2086 out: 2087 return ret_val; 2088 } 2089 2090 /** 2091 * ixgbe_identify_phy_82599 - Get physical layer module 2092 * @hw: pointer to hardware structure 2093 * 2094 * Determines the physical layer module found on the current adapter. 2095 * If PHY already detected, maintains current PHY type in hw struct, 2096 * otherwise executes the PHY detection routine. 2097 **/ 2098 s32 ixgbe_identify_phy_82599(struct ixgbe_hw *hw) 2099 { 2100 s32 status; 2101 2102 DEBUGFUNC("ixgbe_identify_phy_82599"); 2103 2104 /* Detect PHY if not unknown - returns success if already detected. */ 2105 status = ixgbe_identify_phy_generic(hw); 2106 if (status != IXGBE_SUCCESS) { 2107 /* 82599 10GBASE-T requires an external PHY */ 2108 if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_copper) 2109 return status; 2110 else 2111 status = ixgbe_identify_module_generic(hw); 2112 } 2113 2114 /* Set PHY type none if no PHY detected */ 2115 if (hw->phy.type == ixgbe_phy_unknown) { 2116 hw->phy.type = ixgbe_phy_none; 2117 return IXGBE_SUCCESS; 2118 } 2119 2120 /* Return error if SFP module has been detected but is not supported */ 2121 if (hw->phy.type == ixgbe_phy_sfp_unsupported) 2122 return IXGBE_ERR_SFP_NOT_SUPPORTED; 2123 2124 return status; 2125 } 2126 2127 /** 2128 * ixgbe_get_supported_physical_layer_82599 - Returns physical layer type 2129 * @hw: pointer to hardware structure 2130 * 2131 * Determines physical layer capabilities of the current configuration. 2132 **/ 2133 u32 ixgbe_get_supported_physical_layer_82599(struct ixgbe_hw *hw) 2134 { 2135 u32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN; 2136 u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); 2137 u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2); 2138 u32 pma_pmd_10g_serial = autoc2 & IXGBE_AUTOC2_10G_SERIAL_PMA_PMD_MASK; 2139 u32 pma_pmd_10g_parallel = autoc & IXGBE_AUTOC_10G_PMA_PMD_MASK; 2140 u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK; 2141 u16 ext_ability = 0; 2142 2143 DEBUGFUNC("ixgbe_get_support_physical_layer_82599"); 2144 2145 hw->phy.ops.identify(hw); 2146 2147 switch (hw->phy.type) { 2148 case ixgbe_phy_tn: 2149 case ixgbe_phy_cu_unknown: 2150 hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_EXT_ABILITY, 2151 IXGBE_MDIO_PMA_PMD_DEV_TYPE, &ext_ability); 2152 if (ext_ability & IXGBE_MDIO_PHY_10GBASET_ABILITY) 2153 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T; 2154 if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY) 2155 physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T; 2156 if (ext_ability & IXGBE_MDIO_PHY_100BASETX_ABILITY) 2157 physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX; 2158 goto out; 2159 default: 2160 break; 2161 } 2162 2163 switch (autoc & IXGBE_AUTOC_LMS_MASK) { 2164 case IXGBE_AUTOC_LMS_1G_AN: 2165 case IXGBE_AUTOC_LMS_1G_LINK_NO_AN: 2166 if (pma_pmd_1g == IXGBE_AUTOC_1G_KX_BX) { 2167 physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_KX | 2168 IXGBE_PHYSICAL_LAYER_1000BASE_BX; 2169 goto out; 2170 } else 2171 /* SFI mode so read SFP module */ 2172 goto sfp_check; 2173 break; 2174 case IXGBE_AUTOC_LMS_10G_LINK_NO_AN: 2175 if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_CX4) 2176 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_CX4; 2177 else if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_KX4) 2178 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KX4; 2179 else if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_XAUI) 2180 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_XAUI; 2181 goto out; 2182 break; 2183 case IXGBE_AUTOC_LMS_10G_SERIAL: 2184 if (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_KR) { 2185 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KR; 2186 goto out; 2187 } else if (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI) 2188 goto sfp_check; 2189 break; 2190 case IXGBE_AUTOC_LMS_KX4_KX_KR: 2191 case IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN: 2192 if (autoc & IXGBE_AUTOC_KX_SUPP) 2193 physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_KX; 2194 if (autoc & IXGBE_AUTOC_KX4_SUPP) 2195 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KX4; 2196 if (autoc & IXGBE_AUTOC_KR_SUPP) 2197 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KR; 2198 goto out; 2199 break; 2200 default: 2201 goto out; 2202 break; 2203 } 2204 2205 sfp_check: 2206 /* SFP check must be done last since DA modules are sometimes used to 2207 * test KR mode - we need to id KR mode correctly before SFP module. 2208 * Call identify_sfp because the pluggable module may have changed */ 2209 physical_layer = ixgbe_get_supported_phy_sfp_layer_generic(hw); 2210 out: 2211 return physical_layer; 2212 } 2213 2214 /** 2215 * ixgbe_enable_rx_dma_82599 - Enable the Rx DMA unit on 82599 2216 * @hw: pointer to hardware structure 2217 * @regval: register value to write to RXCTRL 2218 * 2219 * Enables the Rx DMA unit for 82599 2220 **/ 2221 s32 ixgbe_enable_rx_dma_82599(struct ixgbe_hw *hw, u32 regval) 2222 { 2223 2224 DEBUGFUNC("ixgbe_enable_rx_dma_82599"); 2225 2226 /* 2227 * Workaround for 82599 silicon errata when enabling the Rx datapath. 2228 * If traffic is incoming before we enable the Rx unit, it could hang 2229 * the Rx DMA unit. Therefore, make sure the security engine is 2230 * completely disabled prior to enabling the Rx unit. 2231 */ 2232 2233 hw->mac.ops.disable_sec_rx_path(hw); 2234 2235 if (regval & IXGBE_RXCTRL_RXEN) 2236 ixgbe_enable_rx(hw); 2237 else 2238 ixgbe_disable_rx(hw); 2239 2240 hw->mac.ops.enable_sec_rx_path(hw); 2241 2242 return IXGBE_SUCCESS; 2243 } 2244 2245 /** 2246 * ixgbe_verify_fw_version_82599 - verify FW version for 82599 2247 * @hw: pointer to hardware structure 2248 * 2249 * Verifies that installed the firmware version is 0.6 or higher 2250 * for SFI devices. All 82599 SFI devices should have version 0.6 or higher. 2251 * 2252 * Returns IXGBE_ERR_EEPROM_VERSION if the FW is not present or 2253 * if the FW version is not supported. 2254 **/ 2255 static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw) 2256 { 2257 s32 status = IXGBE_ERR_EEPROM_VERSION; 2258 u16 fw_offset, fw_ptp_cfg_offset; 2259 u16 fw_version; 2260 2261 DEBUGFUNC("ixgbe_verify_fw_version_82599"); 2262 2263 /* firmware check is only necessary for SFI devices */ 2264 if (hw->phy.media_type != ixgbe_media_type_fiber) { 2265 status = IXGBE_SUCCESS; 2266 goto fw_version_out; 2267 } 2268 2269 /* get the offset to the Firmware Module block */ 2270 if (hw->eeprom.ops.read(hw, IXGBE_FW_PTR, &fw_offset)) { 2271 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 2272 "eeprom read at offset %d failed", IXGBE_FW_PTR); 2273 return IXGBE_ERR_EEPROM_VERSION; 2274 } 2275 2276 if ((fw_offset == 0) || (fw_offset == 0xFFFF)) 2277 goto fw_version_out; 2278 2279 /* get the offset to the Pass Through Patch Configuration block */ 2280 if (hw->eeprom.ops.read(hw, (fw_offset + 2281 IXGBE_FW_PASSTHROUGH_PATCH_CONFIG_PTR), 2282 &fw_ptp_cfg_offset)) { 2283 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 2284 "eeprom read at offset %d failed", 2285 fw_offset + 2286 IXGBE_FW_PASSTHROUGH_PATCH_CONFIG_PTR); 2287 return IXGBE_ERR_EEPROM_VERSION; 2288 } 2289 2290 if ((fw_ptp_cfg_offset == 0) || (fw_ptp_cfg_offset == 0xFFFF)) 2291 goto fw_version_out; 2292 2293 /* get the firmware version */ 2294 if (hw->eeprom.ops.read(hw, (fw_ptp_cfg_offset + 2295 IXGBE_FW_PATCH_VERSION_4), &fw_version)) { 2296 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 2297 "eeprom read at offset %d failed", 2298 fw_ptp_cfg_offset + IXGBE_FW_PATCH_VERSION_4); 2299 return IXGBE_ERR_EEPROM_VERSION; 2300 } 2301 2302 if (fw_version > 0x5) 2303 status = IXGBE_SUCCESS; 2304 2305 fw_version_out: 2306 return status; 2307 } 2308 2309 /** 2310 * ixgbe_verify_lesm_fw_enabled_82599 - Checks LESM FW module state. 2311 * @hw: pointer to hardware structure 2312 * 2313 * Returns TRUE if the LESM FW module is present and enabled. Otherwise 2314 * returns FALSE. Smart Speed must be disabled if LESM FW module is enabled. 2315 **/ 2316 bool ixgbe_verify_lesm_fw_enabled_82599(struct ixgbe_hw *hw) 2317 { 2318 bool lesm_enabled = FALSE; 2319 u16 fw_offset, fw_lesm_param_offset, fw_lesm_state; 2320 s32 status; 2321 2322 DEBUGFUNC("ixgbe_verify_lesm_fw_enabled_82599"); 2323 2324 /* get the offset to the Firmware Module block */ 2325 status = hw->eeprom.ops.read(hw, IXGBE_FW_PTR, &fw_offset); 2326 2327 if ((status != IXGBE_SUCCESS) || 2328 (fw_offset == 0) || (fw_offset == 0xFFFF)) 2329 goto out; 2330 2331 /* get the offset to the LESM Parameters block */ 2332 status = hw->eeprom.ops.read(hw, (fw_offset + 2333 IXGBE_FW_LESM_PARAMETERS_PTR), 2334 &fw_lesm_param_offset); 2335 2336 if ((status != IXGBE_SUCCESS) || 2337 (fw_lesm_param_offset == 0) || (fw_lesm_param_offset == 0xFFFF)) 2338 goto out; 2339 2340 /* get the LESM state word */ 2341 status = hw->eeprom.ops.read(hw, (fw_lesm_param_offset + 2342 IXGBE_FW_LESM_STATE_1), 2343 &fw_lesm_state); 2344 2345 if ((status == IXGBE_SUCCESS) && 2346 (fw_lesm_state & IXGBE_FW_LESM_STATE_ENABLED)) 2347 lesm_enabled = TRUE; 2348 2349 out: 2350 return lesm_enabled; 2351 } 2352 2353 /** 2354 * ixgbe_read_eeprom_buffer_82599 - Read EEPROM word(s) using 2355 * fastest available method 2356 * 2357 * @hw: pointer to hardware structure 2358 * @offset: offset of word in EEPROM to read 2359 * @words: number of words 2360 * @data: word(s) read from the EEPROM 2361 * 2362 * Retrieves 16 bit word(s) read from EEPROM 2363 **/ 2364 static s32 ixgbe_read_eeprom_buffer_82599(struct ixgbe_hw *hw, u16 offset, 2365 u16 words, u16 *data) 2366 { 2367 struct ixgbe_eeprom_info *eeprom = &hw->eeprom; 2368 s32 ret_val = IXGBE_ERR_CONFIG; 2369 2370 DEBUGFUNC("ixgbe_read_eeprom_buffer_82599"); 2371 2372 /* 2373 * If EEPROM is detected and can be addressed using 14 bits, 2374 * use EERD otherwise use bit bang 2375 */ 2376 if ((eeprom->type == ixgbe_eeprom_spi) && 2377 (offset + (words - 1) <= IXGBE_EERD_MAX_ADDR)) 2378 ret_val = ixgbe_read_eerd_buffer_generic(hw, offset, words, 2379 data); 2380 else 2381 ret_val = ixgbe_read_eeprom_buffer_bit_bang_generic(hw, offset, 2382 words, 2383 data); 2384 2385 return ret_val; 2386 } 2387 2388 /** 2389 * ixgbe_read_eeprom_82599 - Read EEPROM word using 2390 * fastest available method 2391 * 2392 * @hw: pointer to hardware structure 2393 * @offset: offset of word in the EEPROM to read 2394 * @data: word read from the EEPROM 2395 * 2396 * Reads a 16 bit word from the EEPROM 2397 **/ 2398 static s32 ixgbe_read_eeprom_82599(struct ixgbe_hw *hw, 2399 u16 offset, u16 *data) 2400 { 2401 struct ixgbe_eeprom_info *eeprom = &hw->eeprom; 2402 s32 ret_val = IXGBE_ERR_CONFIG; 2403 2404 DEBUGFUNC("ixgbe_read_eeprom_82599"); 2405 2406 /* 2407 * If EEPROM is detected and can be addressed using 14 bits, 2408 * use EERD otherwise use bit bang 2409 */ 2410 if ((eeprom->type == ixgbe_eeprom_spi) && 2411 (offset <= IXGBE_EERD_MAX_ADDR)) 2412 ret_val = ixgbe_read_eerd_generic(hw, offset, data); 2413 else 2414 ret_val = ixgbe_read_eeprom_bit_bang_generic(hw, offset, data); 2415 2416 return ret_val; 2417 } 2418 2419 /** 2420 * ixgbe_reset_pipeline_82599 - perform pipeline reset 2421 * 2422 * @hw: pointer to hardware structure 2423 * 2424 * Reset pipeline by asserting Restart_AN together with LMS change to ensure 2425 * full pipeline reset. This function assumes the SW/FW lock is held. 2426 **/ 2427 s32 ixgbe_reset_pipeline_82599(struct ixgbe_hw *hw) 2428 { 2429 s32 ret_val; 2430 u32 anlp1_reg = 0; 2431 u32 i, autoc_reg, autoc2_reg; 2432 2433 /* Enable link if disabled in NVM */ 2434 autoc2_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC2); 2435 if (autoc2_reg & IXGBE_AUTOC2_LINK_DISABLE_MASK) { 2436 autoc2_reg &= ~IXGBE_AUTOC2_LINK_DISABLE_MASK; 2437 IXGBE_WRITE_REG(hw, IXGBE_AUTOC2, autoc2_reg); 2438 IXGBE_WRITE_FLUSH(hw); 2439 } 2440 2441 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); 2442 autoc_reg |= IXGBE_AUTOC_AN_RESTART; 2443 /* Write AUTOC register with toggled LMS[2] bit and Restart_AN */ 2444 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, 2445 autoc_reg ^ (0x4 << IXGBE_AUTOC_LMS_SHIFT)); 2446 /* Wait for AN to leave state 0 */ 2447 for (i = 0; i < 10; i++) { 2448 msec_delay(4); 2449 anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1); 2450 if (anlp1_reg & IXGBE_ANLP1_AN_STATE_MASK) 2451 break; 2452 } 2453 2454 if (!(anlp1_reg & IXGBE_ANLP1_AN_STATE_MASK)) { 2455 DEBUGOUT("auto negotiation not completed\n"); 2456 ret_val = IXGBE_ERR_RESET_FAILED; 2457 goto reset_pipeline_out; 2458 } 2459 2460 ret_val = IXGBE_SUCCESS; 2461 2462 reset_pipeline_out: 2463 /* Write AUTOC register with original LMS field and Restart_AN */ 2464 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg); 2465 IXGBE_WRITE_FLUSH(hw); 2466 2467 return ret_val; 2468 } 2469 2470 /** 2471 * ixgbe_read_i2c_byte_82599 - Reads 8 bit word over I2C 2472 * @hw: pointer to hardware structure 2473 * @byte_offset: byte offset to read 2474 * @data: value read 2475 * 2476 * Performs byte read operation to SFP module's EEPROM over I2C interface at 2477 * a specified device address. 2478 **/ 2479 static s32 ixgbe_read_i2c_byte_82599(struct ixgbe_hw *hw, u8 byte_offset, 2480 u8 dev_addr, u8 *data) 2481 { 2482 u32 esdp; 2483 s32 status; 2484 s32 timeout = 200; 2485 2486 DEBUGFUNC("ixgbe_read_i2c_byte_82599"); 2487 2488 if (hw->phy.qsfp_shared_i2c_bus == TRUE) { 2489 /* Acquire I2C bus ownership. */ 2490 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 2491 esdp |= IXGBE_ESDP_SDP0; 2492 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 2493 IXGBE_WRITE_FLUSH(hw); 2494 2495 while (timeout) { 2496 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 2497 if (esdp & IXGBE_ESDP_SDP1) 2498 break; 2499 2500 msec_delay(5); 2501 timeout--; 2502 } 2503 2504 if (!timeout) { 2505 DEBUGOUT("Driver can't access resource," 2506 " acquiring I2C bus timeout.\n"); 2507 status = IXGBE_ERR_I2C; 2508 goto release_i2c_access; 2509 } 2510 } 2511 2512 status = ixgbe_read_i2c_byte_generic(hw, byte_offset, dev_addr, data); 2513 2514 release_i2c_access: 2515 2516 if (hw->phy.qsfp_shared_i2c_bus == TRUE) { 2517 /* Release I2C bus ownership. */ 2518 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 2519 esdp &= ~IXGBE_ESDP_SDP0; 2520 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 2521 IXGBE_WRITE_FLUSH(hw); 2522 } 2523 2524 return status; 2525 } 2526 2527 /** 2528 * ixgbe_write_i2c_byte_82599 - Writes 8 bit word over I2C 2529 * @hw: pointer to hardware structure 2530 * @byte_offset: byte offset to write 2531 * @data: value to write 2532 * 2533 * Performs byte write operation to SFP module's EEPROM over I2C interface at 2534 * a specified device address. 2535 **/ 2536 static s32 ixgbe_write_i2c_byte_82599(struct ixgbe_hw *hw, u8 byte_offset, 2537 u8 dev_addr, u8 data) 2538 { 2539 u32 esdp; 2540 s32 status; 2541 s32 timeout = 200; 2542 2543 DEBUGFUNC("ixgbe_write_i2c_byte_82599"); 2544 2545 if (hw->phy.qsfp_shared_i2c_bus == TRUE) { 2546 /* Acquire I2C bus ownership. */ 2547 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 2548 esdp |= IXGBE_ESDP_SDP0; 2549 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 2550 IXGBE_WRITE_FLUSH(hw); 2551 2552 while (timeout) { 2553 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 2554 if (esdp & IXGBE_ESDP_SDP1) 2555 break; 2556 2557 msec_delay(5); 2558 timeout--; 2559 } 2560 2561 if (!timeout) { 2562 DEBUGOUT("Driver can't access resource," 2563 " acquiring I2C bus timeout.\n"); 2564 status = IXGBE_ERR_I2C; 2565 goto release_i2c_access; 2566 } 2567 } 2568 2569 status = ixgbe_write_i2c_byte_generic(hw, byte_offset, dev_addr, data); 2570 2571 release_i2c_access: 2572 2573 if (hw->phy.qsfp_shared_i2c_bus == TRUE) { 2574 /* Release I2C bus ownership. */ 2575 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 2576 esdp &= ~IXGBE_ESDP_SDP0; 2577 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 2578 IXGBE_WRITE_FLUSH(hw); 2579 } 2580 2581 return status; 2582 } 2583