1 /* 2 * Copyright (c) 2000 3 * Bill Paul <wpaul@ee.columbia.edu>. All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer. 10 * 2. Redistributions in binary form must reproduce the above copyright 11 * notice, this list of conditions and the following disclaimer in the 12 * documentation and/or other materials provided with the distribution. 13 * 3. All advertising materials mentioning features or use of this software 14 * must display the following acknowledgement: 15 * This product includes software developed by Bill Paul. 16 * 4. Neither the name of the author nor the names of any co-contributors 17 * may be used to endorse or promote products derived from this software 18 * without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 21 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 24 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 30 * THE POSSIBILITY OF SUCH DAMAGE. 31 * 32 * $FreeBSD: src/sys/dev/mii/brgphyreg.h,v 1.1.2.2 2001/10/01 18:31:08 wpaul Exp $ 33 * $DragonFly: src/sys/dev/netif/mii_layer/brgphyreg.h,v 1.5 2008/10/22 14:24:24 sephe Exp $ 34 */ 35 36 #ifndef _DEV_MII_BRGPHYREG_H_ 37 #define _DEV_MII_BRGPHYREG_H_ 38 39 /* 40 * Broadcom BCM5400 registers 41 */ 42 43 #define BRGPHY_MII_BMCR 0x00 44 #define BRGPHY_BMCR_RESET 0x8000 45 #define BRGPHY_BMCR_LOOP 0x4000 46 #define BRGPHY_BMCR_SPD0 0x2000 /* speed select, lower bit */ 47 #define BRGPHY_BMCR_AUTOEN 0x1000 /* Autoneg enabled */ 48 #define BRGPHY_BMCR_PDOWN 0x0800 /* Power down */ 49 #define BRGPHY_BMCR_ISO 0x0400 /* Isolate */ 50 #define BRGPHY_BMCR_STARTNEG 0x0200 /* Restart autoneg */ 51 #define BRGPHY_BMCR_FDX 0x0100 /* Duplex mode */ 52 #define BRGPHY_BMCR_CTEST 0x0080 /* Collision test enable */ 53 #define BRGPHY_BMCR_SPD1 0x0040 /* Speed select, upper bit */ 54 55 #define BRGPHY_S1000 BRGPHY_BMCR_SPD1 /* 1000mbps */ 56 #define BRGPHY_S100 BRGPHY_BMCR_SPD0 /* 100mpbs */ 57 #define BRGPHY_S10 0 /* 10mbps */ 58 59 #define BRGPHY_MII_BMSR 0x01 60 #define BRGPHY_BMSR_EXTSTS 0x0100 /* Extended status present */ 61 #define BRGPHY_BMSR_PRESUB 0x0040 /* Preamble surpression */ 62 #define BRGPHY_BMSR_ACOMP 0x0020 /* Autoneg complete */ 63 #define BRGPHY_BMSR_RFAULT 0x0010 /* Remote fault condition occured */ 64 #define BRGPHY_BMSR_ANEG 0x0008 /* Autoneg capable */ 65 #define BRGPHY_BMSR_LINK 0x0004 /* Link status */ 66 #define BRGPHY_BMSR_JABBER 0x0002 /* Jabber detected */ 67 #define BRGPHY_BMSR_EXT 0x0001 /* Extended capability */ 68 69 #define BRGPHY_MII_ANAR 0x04 70 #define BRGPHY_ANAR_NP 0x8000 /* Next page */ 71 #define BRGPHY_ANAR_RF 0x2000 /* Remote fault */ 72 #define BRGPHY_ANAR_ASP 0x0800 /* Asymmetric Pause */ 73 #define BRGPHY_ANAR_PC 0x0400 /* Pause capable */ 74 #define BRGPHY_ANAR_SEL 0x001F /* selector field, 00001=Ethernet */ 75 76 #define BRGPHY_MII_ANLPAR 0x05 77 #define BRGPHY_ANLPAR_NP 0x8000 /* Next page */ 78 #define BRGPHY_ANLPAR_RF 0x2000 /* Remote fault */ 79 #define BRGPHY_ANLPAR_ASP 0x0800 /* Asymmetric Pause */ 80 #define BRGPHY_ANLPAR_PC 0x0400 /* Pause capable */ 81 #define BRGPHY_ANLPAR_SEL 0x001F /* selector field, 00001=Ethernet */ 82 83 #define BRGPHY_SEL_TYPE 0x0001 /* ethernet */ 84 85 #define BRGPHY_MII_ANER 0x06 86 #define BRGPHY_ANER_PDF 0x0010 /* Parallel detection fault */ 87 #define BRGPHY_ANER_LPNP 0x0008 /* Link partner can next page */ 88 #define BRGPHY_ANER_NP 0x0004 /* Local PHY can next page */ 89 #define BRGPHY_ANER_RX 0x0002 /* Next page received */ 90 #define BRGPHY_ANER_LPAN 0x0001 /* Link partner autoneg capable */ 91 92 #define BRGPHY_MII_NEXTP 0x07 /* Next page */ 93 94 #define BRGPHY_MII_NEXTP_LP 0x08 /* Next page of link partner */ 95 96 #define BRGPHY_MII_1000CTL 0x09 /* 1000baseT control */ 97 #define BRGPHY_1000CTL_TST 0xE000 /* test modes */ 98 #define BRGPHY_1000CTL_MSE 0x1000 /* Master/Slave enable */ 99 #define BRGPHY_1000CTL_MSC 0x0800 /* Master/Slave configuration */ 100 #define BRGPHY_1000CTL_RD 0x0400 /* Repeater/DTE */ 101 #define BRGPHY_1000CTL_AFD 0x0200 /* Advertise full duplex */ 102 #define BRGPHY_1000CTL_AHD 0x0100 /* Advertise half duplex */ 103 104 #define BRGPHY_MII_1000STS 0x0A /* 1000baseT status */ 105 #define BRGPHY_1000STS_MSF 0x8000 /* Master/slave fault */ 106 #define BRGPHY_1000STS_MSR 0x4000 /* Master/slave result */ 107 #define BRGPHY_1000STS_LRS 0x2000 /* Local receiver status */ 108 #define BRGPHY_1000STS_RRS 0x1000 /* Remote receiver status */ 109 #define BRGPHY_1000STS_LPFD 0x0800 /* Link partner can FD */ 110 #define BRGPHY_1000STS_LPHD 0x0400 /* Link partner can HD */ 111 #define BRGPHY_1000STS_IEC 0x00FF /* Idle error count */ 112 113 #define BRGPHY_MII_EXTSTS 0x0F /* Extended status */ 114 #define BRGPHY_EXTSTS_X_FD_CAP 0x8000 /* 1000base-X FD capable */ 115 #define BRGPHY_EXTSTS_X_HD_CAP 0x4000 /* 1000base-X HD capable */ 116 #define BRGPHY_EXTSTS_T_FD_CAP 0x2000 /* 1000base-T FD capable */ 117 #define BRGPHY_EXTSTS_T_HD_CAP 0x1000 /* 1000base-T HD capable */ 118 119 #define BRGPHY_MII_PHY_EXTCTL 0x10 /* PHY extended control */ 120 #define BRGPHY_PHY_EXTCTL_MAC_PHY 0x8000 /* 10BIT/GMI-interface */ 121 #define BRGPHY_PHY_EXTCTL_DIS_CROSS 0x4000 /* Disable MDI crossover */ 122 #define BRGPHY_PHY_EXTCTL_TX_DIS 0x2000 /* Tx output disable d*/ 123 #define BRGPHY_PHY_EXTCTL_INT_DIS 0x1000 /* Interrupts disabled */ 124 #define BRGPHY_PHY_EXTCTL_F_INT 0x0800 /* Force interrupt */ 125 #define BRGPHY_PHY_EXTCTL_BY_45 0x0400 /* Bypass 4B5B-Decoder */ 126 #define BRGPHY_PHY_EXTCTL_BY_SCR 0x0200 /* Bypass scrambler */ 127 #define BRGPHY_PHY_EXTCTL_BY_MLT3 0x0100 /* Bypass MLT3 encoder */ 128 #define BRGPHY_PHY_EXTCTL_BY_RXA 0x0080 /* Bypass RX alignment */ 129 #define BRGPHY_PHY_EXTCTL_RES_SCR 0x0040 /* Reset scrambler */ 130 #define BRGPHY_PHY_EXTCTL_EN_LTR 0x0020 /* Enable LED traffic mode */ 131 #define BRGPHY_PHY_EXTCTL_LED_ON 0x0010 /* Force LEDs on */ 132 #define BRGPHY_PHY_EXTCTL_LED_OFF 0x0008 /* Force LEDs off */ 133 #define BRGPHY_PHY_EXTCTL_EX_IPG 0x0004 /* Extended TX IPG mode */ 134 #define BRGPHY_PHY_EXTCTL_3_LED 0x0002 /* Three link LED mode */ 135 #define BRGPHY_PHY_EXTCTL_HIGH_LA 0x0001 /* GMII Fifo Elasticy (?) */ 136 137 #define BRGPHY_MII_PHY_EXTSTS 0x11 /* PHY extended status */ 138 #define BRGPHY_PHY_EXTSTS_CROSS_STAT 0x2000 /* MDI crossover status */ 139 #define BRGPHY_PHY_EXTSTS_INT_STAT 0x1000 /* Interrupt status */ 140 #define BRGPHY_PHY_EXTSTS_RRS 0x0800 /* Remote receiver status */ 141 #define BRGPHY_PHY_EXTSTS_LRS 0x0400 /* Local receiver status */ 142 #define BRGPHY_PHY_EXTSTS_LOCKED 0x0200 /* Locked */ 143 #define BRGPHY_PHY_EXTSTS_LS 0x0100 /* Link status */ 144 #define BRGPHY_PHY_EXTSTS_RF 0x0080 /* Remove fault */ 145 #define BRGPHY_PHY_EXTSTS_CE_ER 0x0040 /* Carrier ext error */ 146 #define BRGPHY_PHY_EXTSTS_BAD_SSD 0x0020 /* Bad SSD */ 147 #define BRGPHY_PHY_EXTSTS_BAD_ESD 0x0010 /* Bad ESS */ 148 #define BRGPHY_PHY_EXTSTS_RX_ER 0x0008 /* RX error */ 149 #define BRGPHY_PHY_EXTSTS_TX_ER 0x0004 /* TX error */ 150 #define BRGPHY_PHY_EXTSTS_LOCK_ER 0x0002 /* Lock error */ 151 #define BRGPHY_PHY_EXTSTS_MLT3_ER 0x0001 /* MLT3 code error */ 152 153 #define BRGPHY_MII_RXERRCNT 0x12 /* RX error counter */ 154 155 #define BRGPHY_MII_FCERRCNT 0x13 /* false carrier sense counter */ 156 #define BGRPHY_FCERRCNT 0x00FF /* False carrier counter */ 157 158 #define BRGPHY_MII_RXNOCNT 0x14 /* RX not OK counter */ 159 #define BRGPHY_RXNOCNT_LOCAL 0xFF00 /* Local RX not OK counter */ 160 #define BRGPHY_RXNOCNT_REMOTE 0x00FF /* Local RX not OK counter */ 161 162 #define BRGPHY_MII_DSP_RW_PORT 0x15 /* DSP coefficient r/w port */ 163 164 #define BRGPHY_MII_DSP_ADDR_REG 0x17 /* DSP coefficient addr register */ 165 #define BRGPHY_MII_EPHY_PTEST 0x17 /* 5906 PHY register */ 166 167 #define BRGPHY_DSP_TAP_NUMBER_MASK 0x00 168 #define BRGPHY_DSP_AGC_A 0x00 169 #define BRGPHY_DSP_AGC_B 0x01 170 #define BRGPHY_DSP_MSE_PAIR_STATUS 0x02 171 #define BRGPHY_DSP_SOFT_DECISION 0x03 172 #define BRGPHY_DSP_PHASE_REG 0x04 173 #define BRGPHY_DSP_SKEW 0x05 174 #define BRGPHY_DSP_POWER_SAVER_UPPER_BOUND 0x06 175 #define BRGPHY_DSP_POWER_SAVER_LOWER_BOUND 0x07 176 #define BRGPHY_DSP_LAST_ECHO 0x08 177 #define BRGPHY_DSP_FREQUENCY 0x09 178 #define BRGPHY_DSP_PLL_BANDWIDTH 0x0A 179 #define BRGPHY_DSP_PLL_PHASE_OFFSET 0x0B 180 181 #define BRGPHYDSP_FILTER_DCOFFSET 0x0C00 182 #define BRGPHY_DSP_FILTER_FEXT3 0x0B00 183 #define BRGPHY_DSP_FILTER_FEXT2 0x0A00 184 #define BRGPHY_DSP_FILTER_FEXT1 0x0900 185 #define BRGPHY_DSP_FILTER_FEXT0 0x0800 186 #define BRGPHY_DSP_FILTER_NEXT3 0x0700 187 #define BRGPHY_DSP_FILTER_NEXT2 0x0600 188 #define BRGPHY_DSP_FILTER_NEXT1 0x0500 189 #define BRGPHY_DSP_FILTER_NEXT0 0x0400 190 #define BRGPHY_DSP_FILTER_ECHO 0x0300 191 #define BRGPHY_DSP_FILTER_DFE 0x0200 192 #define BRGPHY_DSP_FILTER_FFE 0x0100 193 194 #define BRGPHY_DSP_CONTROL_ALL_FILTERS 0x1000 195 196 #define BRGPHY_DSP_SEL_CH_0 0x0000 197 #define BRGPHY_DSP_SEL_CH_1 0x2000 198 #define BRGPHY_DSP_SEL_CH_2 0x4000 199 #define BRGPHY_DSP_SEL_CH_3 0x6000 200 201 #define BRGPHY_MII_AUXCTL 0x18 /* AUX control */ 202 #define BRGPHY_AUXCTL_LOW_SQ 0x8000 /* Low squelch */ 203 #define BRGPHY_AUXCTL_LONG_PKT 0x4000 /* RX long packets */ 204 #define BRGPHY_AUXCTL_ER_CTL 0x3000 /* Edgerate control */ 205 #define BRGPHY_AUXCTL_TX_TST 0x0400 /* TX test, always 1 */ 206 #define BRGPHY_AUXCTL_DIS_PRF 0x0080 /* dis part resp filter */ 207 #define BRGPHY_AUXCTL_DIAG_MODE 0x0004 /* Diagnostic mode */ 208 209 #define BRGPHY_MII_AUXSTS 0x19 /* AUX status */ 210 #define BRGPHY_AUXSTS_ACOMP 0x8000 /* autoneg complete */ 211 #define BRGPHY_AUXSTS_AN_ACK 0x4000 /* autoneg complete ack */ 212 #define BRGPHY_AUXSTS_AN_ACK_D 0x2000 /* autoneg complete ack detect */ 213 #define BRGPHY_AUXSTS_AN_NPW 0x1000 /* autoneg next page wait */ 214 #define BRGPHY_AUXSTS_AN_RES 0x0700 /* AN HDC */ 215 #define BRGPHY_AUXSTS_PDF 0x0080 /* Parallel detect. fault */ 216 #define BRGPHY_AUXSTS_RF 0x0040 /* remote fault */ 217 #define BRGPHY_AUXSTS_ANP_R 0x0020 /* AN page received */ 218 #define BRGPHY_AUXSTS_LP_ANAB 0x0010 /* LP AN ability */ 219 #define BRGPHY_AUXSTS_LP_NPAB 0x0008 /* LP Next page ability */ 220 #define BRGPHY_AUXSTS_LINK 0x0004 /* Link status */ 221 #define BRGPHY_AUXSTS_PRR 0x0002 /* Pause resolution-RX */ 222 #define BRGPHY_AUXSTS_PRT 0x0001 /* Pause resolution-TX */ 223 224 #define BRGPHY_RES_1000FD 0x0700 /* 1000baseT full duplex */ 225 #define BRGPHY_RES_1000HD 0x0600 /* 1000baseT half duplex */ 226 #define BRGPHY_RES_100FD 0x0500 /* 100baseT full duplex */ 227 #define BRGPHY_RES_100T4 0x0400 /* 100baseT4 */ 228 #define BRGPHY_RES_100HD 0x0300 /* 100baseT half duplex */ 229 #define BRGPHY_RES_10FD 0x0200 /* 10baseT full duplex */ 230 #define BRGPHY_RES_10HD 0x0100 /* 10baseT half duplex */ 231 /* 5906 */ 232 #define BRGPHY_RES_100 0x0008 /* 100baseT */ 233 #define BRGPHY_RES_FULL 0x0001 /* full duplex */ 234 235 #define BRGPHY_MII_ISR 0x1A /* interrupt status */ 236 #define BRGPHY_ISR_PSERR 0x4000 /* Pair swap error */ 237 #define BRGPHY_ISR_MDXI_SC 0x2000 /* MDIX Status Change */ 238 #define BRGPHY_ISR_HCT 0x1000 /* counter above 32K */ 239 #define BRGPHY_ISR_LCT 0x0800 /* all counter below 128 */ 240 #define BRGPHY_ISR_AN_PR 0x0400 /* Autoneg page received */ 241 #define BRGPHY_ISR_NO_HDCL 0x0200 /* No HCD Link */ 242 #define BRGPHY_ISR_NO_HDC 0x0100 /* No HCD */ 243 #define BRGPHY_ISR_USHDC 0x0080 /* Negotiated Unsupported HCD */ 244 #define BRGPHY_ISR_SCR_S_ERR 0x0040 /* Scrambler sync error */ 245 #define BRGPHY_ISR_RRS_CHG 0x0020 /* Remote RX status change */ 246 #define BRGPHY_ISR_LRS_CHG 0x0010 /* Local RX status change */ 247 #define BRGPHY_ISR_DUP_CHG 0x0008 /* Duplex mode change */ 248 #define BRGPHY_ISR_LSP_CHG 0x0004 /* Link speed changed */ 249 #define BRGPHY_ISR_LNK_CHG 0x0002 /* Link status change */ 250 #define BRGPHY_ISR_CRCERR 0x0001 /* CEC error */ 251 252 #define BRGPHY_MII_IMR 0x1B /* interrupt mask */ 253 #define BRGPHY_IMR_PSERR 0x4000 /* Pair swap error */ 254 #define BRGPHY_IMR_MDXI_SC 0x2000 /* MDIX Status Change */ 255 #define BRGPHY_IMR_HCT 0x1000 /* counter above 32K */ 256 #define BRGPHY_IMR_LCT 0x0800 /* all counter below 128 */ 257 #define BRGPHY_IMR_AN_PR 0x0400 /* Autoneg page received */ 258 #define BRGPHY_IMR_NO_HDCL 0x0200 /* No HCD Link */ 259 #define BRGPHY_IMR_NO_HDC 0x0100 /* No HCD */ 260 #define BRGPHY_IMR_USHDC 0x0080 /* Negotiated Unsupported HCD */ 261 #define BRGPHY_IMR_SCR_S_ERR 0x0040 /* Scrambler sync error */ 262 #define BRGPHY_IMR_RRS_CHG 0x0020 /* Remote RX status change */ 263 #define BRGPHY_IMR_LRS_CHG 0x0010 /* Local RX status change */ 264 #define BRGPHY_IMR_DUP_CHG 0x0008 /* Duplex mode change */ 265 #define BRGPHY_IMR_LSP_CHG 0x0004 /* Link speed changed */ 266 #define BRGPHY_IMR_LNK_CHG 0x0002 /* Link status change */ 267 #define BRGPHY_IMR_CRCERR 0x0001 /* CEC error */ 268 269 #define BRGPHY_TEST1 0x1E 270 #define BRGPHY_TEST1_TRIM_EN 0x0010 271 272 #define BRGPHY_INTRS \ 273 ~(BRGPHY_IMR_LNK_CHG|BRGPHY_IMR_LSP_CHG|BRGPHY_IMR_DUP_CHG) 274 275 #endif /* _DEV_BRGPHY_MIIREG_H_ */ 276