1Binding for Silicon Labs Si5351a/b/c programmable i2c clock generator.
2
3Reference
4[1] Si5351A/B/C Data Sheet
5    https://www.silabs.com/Support%20Documents/TechnicalDocs/Si5351.pdf
6
7The Si5351a/b/c are programmable i2c clock generators with up to 8 output
8clocks. Si5351a also has a reduced pin-count package (MSOP10) where only
93 output clocks are accessible. The internal structure of the clock
10generators can be found in [1].
11
12==I2C device node==
13
14Required properties:
15- compatible: shall be one of the following:
16	"silabs,si5351a" - Si5351a, QFN20 package
17	"silabs,si5351a-msop" - Si5351a, MSOP10 package
18	"silabs,si5351b" - Si5351b, QFN20 package
19	"silabs,si5351c" - Si5351c, QFN20 package
20- reg: i2c device address, shall be 0x60 or 0x61.
21- #clock-cells: from common clock binding; shall be set to 1.
22- clocks: from common clock binding; list of parent clock
23  handles, shall be xtal reference clock or xtal and clkin for
24  si5351c only. Corresponding clock input names are "xtal" and
25  "clkin" respectively.
26- #address-cells: shall be set to 1.
27- #size-cells: shall be set to 0.
28
29Optional properties:
30- silabs,pll-source: pair of (number, source) for each pll. Allows
31  to overwrite clock source of pll A (number=0) or B (number=1).
32
33==Child nodes==
34
35Each of the clock outputs can be overwritten individually by
36using a child node to the I2C device node. If a child node for a clock
37output is not set, the eeprom configuration is not overwritten.
38
39Required child node properties:
40- reg: number of clock output.
41
42Optional child node properties:
43- silabs,clock-source: source clock of the output divider stage N, shall be
44  0 = multisynth N
45  1 = multisynth 0 for output clocks 0-3, else multisynth4
46  2 = xtal
47  3 = clkin (si5351c only)
48- silabs,drive-strength: output drive strength in mA, shall be one of {2,4,6,8}.
49- silabs,multisynth-source: source pll A(0) or B(1) of corresponding multisynth
50  divider.
51- silabs,pll-master: boolean, multisynth can change pll frequency.
52- silabs,pll-reset: boolean, clock output can reset its pll.
53- silabs,disable-state : clock output disable state, shall be
54  0 = clock output is driven LOW when disabled
55  1 = clock output is driven HIGH when disabled
56  2 = clock output is FLOATING (HIGH-Z) when disabled
57  3 = clock output is NEVER disabled
58
59==Example==
60
61/* 25MHz reference crystal */
62ref25: ref25M {
63	compatible = "fixed-clock";
64	#clock-cells = <0>;
65	clock-frequency = <25000000>;
66};
67
68i2c-master-node {
69
70	/* Si5351a msop10 i2c clock generator */
71	si5351a: clock-generator@60 {
72		compatible = "silabs,si5351a-msop";
73		reg = <0x60>;
74		#address-cells = <1>;
75		#size-cells = <0>;
76		#clock-cells = <1>;
77
78		/* connect xtal input to 25MHz reference */
79		clocks = <&ref25>;
80		clock-names = "xtal";
81
82		/* connect xtal input as source of pll0 and pll1 */
83		silabs,pll-source = <0 0>, <1 0>;
84
85		/*
86		 * overwrite clkout0 configuration with:
87		 * - 8mA output drive strength
88		 * - pll0 as clock source of multisynth0
89		 * - multisynth0 as clock source of output divider
90		 * - multisynth0 can change pll0
91		 * - set initial clock frequency of 74.25MHz
92		 */
93		clkout0 {
94			reg = <0>;
95			silabs,drive-strength = <8>;
96			silabs,multisynth-source = <0>;
97			silabs,clock-source = <0>;
98			silabs,pll-master;
99			clock-frequency = <74250000>;
100		};
101
102		/*
103		 * overwrite clkout1 configuration with:
104		 * - 4mA output drive strength
105		 * - pll1 as clock source of multisynth1
106		 * - multisynth1 as clock source of output divider
107		 * - multisynth1 can change pll1
108		 */
109		clkout1 {
110			reg = <1>;
111			silabs,drive-strength = <4>;
112			silabs,multisynth-source = <1>;
113			silabs,clock-source = <0>;
114			pll-master;
115		};
116
117		/*
118		 * overwrite clkout2 configuration with:
119		 * - xtal as clock source of output divider
120		 */
121		clkout2 {
122			reg = <2>;
123			silabs,clock-source = <2>;
124		};
125	};
126};
127