1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * pata_cmd64x.c - CMD64x PATA for new ATA layer
4 * (C) 2005 Red Hat Inc
5 * Alan Cox <alan@lxorguk.ukuu.org.uk>
6 * (C) 2009-2010 Bartlomiej Zolnierkiewicz
7 * (C) 2012 MontaVista Software, LLC <source@mvista.com>
8 *
9 * Based upon
10 * linux/drivers/ide/pci/cmd64x.c Version 1.30 Sept 10, 2002
11 *
12 * cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines.
13 * Note, this driver is not used at all on other systems because
14 * there the "BIOS" has done all of the following already.
15 * Due to massive hardware bugs, UltraDMA is only supported
16 * on the 646U2 and not on the 646U.
17 *
18 * Copyright (C) 1998 Eddie C. Dost (ecd@skynet.be)
19 * Copyright (C) 1998 David S. Miller (davem@redhat.com)
20 *
21 * Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
22 *
23 * TODO
24 * Testing work
25 */
26
27 #include <linux/kernel.h>
28 #include <linux/module.h>
29 #include <linux/pci.h>
30 #include <linux/blkdev.h>
31 #include <linux/delay.h>
32 #include <scsi/scsi_host.h>
33 #include <linux/libata.h>
34
35 #define DRV_NAME "pata_cmd64x"
36 #define DRV_VERSION "0.2.18"
37
38 /*
39 * CMD64x specific registers definition.
40 */
41
42 enum {
43 CFR = 0x50,
44 CFR_INTR_CH0 = 0x04,
45 CNTRL = 0x51,
46 CNTRL_CH0 = 0x04,
47 CNTRL_CH1 = 0x08,
48 CMDTIM = 0x52,
49 ARTTIM0 = 0x53,
50 DRWTIM0 = 0x54,
51 ARTTIM1 = 0x55,
52 DRWTIM1 = 0x56,
53 ARTTIM23 = 0x57,
54 ARTTIM23_DIS_RA2 = 0x04,
55 ARTTIM23_DIS_RA3 = 0x08,
56 ARTTIM23_INTR_CH1 = 0x10,
57 DRWTIM2 = 0x58,
58 BRST = 0x59,
59 DRWTIM3 = 0x5b,
60 BMIDECR0 = 0x70,
61 MRDMODE = 0x71,
62 MRDMODE_INTR_CH0 = 0x04,
63 MRDMODE_INTR_CH1 = 0x08,
64 BMIDESR0 = 0x72,
65 UDIDETCR0 = 0x73,
66 DTPR0 = 0x74,
67 BMIDECR1 = 0x78,
68 BMIDECSR = 0x79,
69 UDIDETCR1 = 0x7B,
70 DTPR1 = 0x7C
71 };
72
cmd648_cable_detect(struct ata_port * ap)73 static int cmd648_cable_detect(struct ata_port *ap)
74 {
75 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
76 u8 r;
77
78 /* Check cable detect bits */
79 pci_read_config_byte(pdev, BMIDECSR, &r);
80 if (r & (1 << ap->port_no))
81 return ATA_CBL_PATA80;
82 return ATA_CBL_PATA40;
83 }
84
85 /**
86 * cmd64x_set_timing - set PIO and MWDMA timing
87 * @ap: ATA interface
88 * @adev: ATA device
89 * @mode: mode
90 *
91 * Called to do the PIO and MWDMA mode setup.
92 */
93
cmd64x_set_timing(struct ata_port * ap,struct ata_device * adev,u8 mode)94 static void cmd64x_set_timing(struct ata_port *ap, struct ata_device *adev, u8 mode)
95 {
96 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
97 struct ata_timing t;
98 const unsigned long T = 1000000 / 33;
99 const u8 setup_data[] = { 0x40, 0x40, 0x40, 0x80, 0x00 };
100
101 u8 reg;
102
103 /* Port layout is not logical so use a table */
104 const u8 arttim_port[2][2] = {
105 { ARTTIM0, ARTTIM1 },
106 { ARTTIM23, ARTTIM23 }
107 };
108 const u8 drwtim_port[2][2] = {
109 { DRWTIM0, DRWTIM1 },
110 { DRWTIM2, DRWTIM3 }
111 };
112
113 int arttim = arttim_port[ap->port_no][adev->devno];
114 int drwtim = drwtim_port[ap->port_no][adev->devno];
115
116 /* ata_timing_compute is smart and will produce timings for MWDMA
117 that don't violate the drives PIO capabilities. */
118 if (ata_timing_compute(adev, mode, &t, T, 0) < 0) {
119 printk(KERN_ERR DRV_NAME ": mode computation failed.\n");
120 return;
121 }
122 if (ap->port_no) {
123 /* Slave has shared address setup */
124 struct ata_device *pair = ata_dev_pair(adev);
125
126 if (pair) {
127 struct ata_timing tp;
128 ata_timing_compute(pair, pair->pio_mode, &tp, T, 0);
129 ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP);
130 }
131 }
132
133 printk(KERN_DEBUG DRV_NAME ": active %d recovery %d setup %d.\n",
134 t.active, t.recover, t.setup);
135 if (t.recover > 16) {
136 t.active += t.recover - 16;
137 t.recover = 16;
138 }
139 if (t.active > 16)
140 t.active = 16;
141
142 /* Now convert the clocks into values we can actually stuff into
143 the chip */
144
145 if (t.recover == 16)
146 t.recover = 0;
147 else if (t.recover > 1)
148 t.recover--;
149 else
150 t.recover = 15;
151
152 if (t.setup > 4)
153 t.setup = 0xC0;
154 else
155 t.setup = setup_data[t.setup];
156
157 t.active &= 0x0F; /* 0 = 16 */
158
159 /* Load setup timing */
160 pci_read_config_byte(pdev, arttim, ®);
161 reg &= 0x3F;
162 reg |= t.setup;
163 pci_write_config_byte(pdev, arttim, reg);
164
165 /* Load active/recovery */
166 pci_write_config_byte(pdev, drwtim, (t.active << 4) | t.recover);
167 }
168
169 /**
170 * cmd64x_set_piomode - set initial PIO mode data
171 * @ap: ATA interface
172 * @adev: ATA device
173 *
174 * Used when configuring the devices ot set the PIO timings. All the
175 * actual work is done by the PIO/MWDMA setting helper
176 */
177
cmd64x_set_piomode(struct ata_port * ap,struct ata_device * adev)178 static void cmd64x_set_piomode(struct ata_port *ap, struct ata_device *adev)
179 {
180 cmd64x_set_timing(ap, adev, adev->pio_mode);
181 }
182
183 /**
184 * cmd64x_set_dmamode - set initial DMA mode data
185 * @ap: ATA interface
186 * @adev: ATA device
187 *
188 * Called to do the DMA mode setup.
189 */
190
cmd64x_set_dmamode(struct ata_port * ap,struct ata_device * adev)191 static void cmd64x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
192 {
193 static const u8 udma_data[] = {
194 0x30, 0x20, 0x10, 0x20, 0x10, 0x00
195 };
196
197 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
198 u8 regU, regD;
199
200 int pciU = UDIDETCR0 + 8 * ap->port_no;
201 int pciD = BMIDESR0 + 8 * ap->port_no;
202 int shift = 2 * adev->devno;
203
204 pci_read_config_byte(pdev, pciD, ®D);
205 pci_read_config_byte(pdev, pciU, ®U);
206
207 /* DMA bits off */
208 regD &= ~(0x20 << adev->devno);
209 /* DMA control bits */
210 regU &= ~(0x30 << shift);
211 /* DMA timing bits */
212 regU &= ~(0x05 << adev->devno);
213
214 if (adev->dma_mode >= XFER_UDMA_0) {
215 /* Merge the timing value */
216 regU |= udma_data[adev->dma_mode - XFER_UDMA_0] << shift;
217 /* Merge the control bits */
218 regU |= 1 << adev->devno; /* UDMA on */
219 if (adev->dma_mode > XFER_UDMA_2) /* 15nS timing */
220 regU |= 4 << adev->devno;
221 } else {
222 regU &= ~ (1 << adev->devno); /* UDMA off */
223 cmd64x_set_timing(ap, adev, adev->dma_mode);
224 }
225
226 regD |= 0x20 << adev->devno;
227
228 pci_write_config_byte(pdev, pciU, regU);
229 pci_write_config_byte(pdev, pciD, regD);
230 }
231
232 /**
233 * cmd64x_sff_irq_check - check IDE interrupt
234 * @ap: ATA interface
235 *
236 * Check IDE interrupt in CFR/ARTTIM23 registers.
237 */
238
cmd64x_sff_irq_check(struct ata_port * ap)239 static bool cmd64x_sff_irq_check(struct ata_port *ap)
240 {
241 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
242 int irq_mask = ap->port_no ? ARTTIM23_INTR_CH1 : CFR_INTR_CH0;
243 int irq_reg = ap->port_no ? ARTTIM23 : CFR;
244 u8 irq_stat;
245
246 /* NOTE: reading the register should clear the interrupt */
247 pci_read_config_byte(pdev, irq_reg, &irq_stat);
248
249 return irq_stat & irq_mask;
250 }
251
252 /**
253 * cmd64x_sff_irq_clear - clear IDE interrupt
254 * @ap: ATA interface
255 *
256 * Clear IDE interrupt in CFR/ARTTIM23 and DMA status registers.
257 */
258
cmd64x_sff_irq_clear(struct ata_port * ap)259 static void cmd64x_sff_irq_clear(struct ata_port *ap)
260 {
261 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
262 int irq_reg = ap->port_no ? ARTTIM23 : CFR;
263 u8 irq_stat;
264
265 ata_bmdma_irq_clear(ap);
266
267 /* Reading the register should be enough to clear the interrupt */
268 pci_read_config_byte(pdev, irq_reg, &irq_stat);
269 }
270
271 /**
272 * cmd648_sff_irq_check - check IDE interrupt
273 * @ap: ATA interface
274 *
275 * Check IDE interrupt in MRDMODE register.
276 */
277
cmd648_sff_irq_check(struct ata_port * ap)278 static bool cmd648_sff_irq_check(struct ata_port *ap)
279 {
280 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
281 unsigned long base = pci_resource_start(pdev, 4);
282 int irq_mask = ap->port_no ? MRDMODE_INTR_CH1 : MRDMODE_INTR_CH0;
283 u8 mrdmode = inb(base + 1);
284
285 return mrdmode & irq_mask;
286 }
287
288 /**
289 * cmd648_sff_irq_clear - clear IDE interrupt
290 * @ap: ATA interface
291 *
292 * Clear IDE interrupt in MRDMODE and DMA status registers.
293 */
294
cmd648_sff_irq_clear(struct ata_port * ap)295 static void cmd648_sff_irq_clear(struct ata_port *ap)
296 {
297 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
298 unsigned long base = pci_resource_start(pdev, 4);
299 int irq_mask = ap->port_no ? MRDMODE_INTR_CH1 : MRDMODE_INTR_CH0;
300 u8 mrdmode;
301
302 ata_bmdma_irq_clear(ap);
303
304 /* Clear this port's interrupt bit (leaving the other port alone) */
305 mrdmode = inb(base + 1);
306 mrdmode &= ~(MRDMODE_INTR_CH0 | MRDMODE_INTR_CH1);
307 outb(mrdmode | irq_mask, base + 1);
308 }
309
310 /**
311 * cmd646r1_bmdma_stop - DMA stop callback
312 * @qc: Command in progress
313 *
314 * Stub for now while investigating the r1 quirk in the old driver.
315 */
316
cmd646r1_bmdma_stop(struct ata_queued_cmd * qc)317 static void cmd646r1_bmdma_stop(struct ata_queued_cmd *qc)
318 {
319 ata_bmdma_stop(qc);
320 }
321
322 static struct scsi_host_template cmd64x_sht = {
323 ATA_BMDMA_SHT(DRV_NAME),
324 };
325
326 static const struct ata_port_operations cmd64x_base_ops = {
327 .inherits = &ata_bmdma_port_ops,
328 .set_piomode = cmd64x_set_piomode,
329 .set_dmamode = cmd64x_set_dmamode,
330 };
331
332 static struct ata_port_operations cmd64x_port_ops = {
333 .inherits = &cmd64x_base_ops,
334 .sff_irq_check = cmd64x_sff_irq_check,
335 .sff_irq_clear = cmd64x_sff_irq_clear,
336 .cable_detect = ata_cable_40wire,
337 };
338
339 static struct ata_port_operations cmd646r1_port_ops = {
340 .inherits = &cmd64x_base_ops,
341 .sff_irq_check = cmd64x_sff_irq_check,
342 .sff_irq_clear = cmd64x_sff_irq_clear,
343 .bmdma_stop = cmd646r1_bmdma_stop,
344 .cable_detect = ata_cable_40wire,
345 };
346
347 static struct ata_port_operations cmd646r3_port_ops = {
348 .inherits = &cmd64x_base_ops,
349 .sff_irq_check = cmd648_sff_irq_check,
350 .sff_irq_clear = cmd648_sff_irq_clear,
351 .cable_detect = ata_cable_40wire,
352 };
353
354 static struct ata_port_operations cmd648_port_ops = {
355 .inherits = &cmd64x_base_ops,
356 .sff_irq_check = cmd648_sff_irq_check,
357 .sff_irq_clear = cmd648_sff_irq_clear,
358 .cable_detect = cmd648_cable_detect,
359 };
360
cmd64x_fixup(struct pci_dev * pdev)361 static void cmd64x_fixup(struct pci_dev *pdev)
362 {
363 u8 mrdmode;
364
365 pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64);
366 pci_read_config_byte(pdev, MRDMODE, &mrdmode);
367 mrdmode &= ~0x30; /* IRQ set up */
368 mrdmode |= 0x02; /* Memory read line enable */
369 pci_write_config_byte(pdev, MRDMODE, mrdmode);
370
371 /* PPC specific fixup copied from old driver */
372 #ifdef CONFIG_PPC
373 pci_write_config_byte(pdev, UDIDETCR0, 0xF0);
374 #endif
375 }
376
cmd64x_init_one(struct pci_dev * pdev,const struct pci_device_id * id)377 static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
378 {
379 static const struct ata_port_info cmd_info[7] = {
380 { /* CMD 643 - no UDMA */
381 .flags = ATA_FLAG_SLAVE_POSS,
382 .pio_mask = ATA_PIO4,
383 .mwdma_mask = ATA_MWDMA2,
384 .port_ops = &cmd64x_port_ops
385 },
386 { /* CMD 646 with broken UDMA */
387 .flags = ATA_FLAG_SLAVE_POSS,
388 .pio_mask = ATA_PIO4,
389 .mwdma_mask = ATA_MWDMA2,
390 .port_ops = &cmd64x_port_ops
391 },
392 { /* CMD 646U with broken UDMA */
393 .flags = ATA_FLAG_SLAVE_POSS,
394 .pio_mask = ATA_PIO4,
395 .mwdma_mask = ATA_MWDMA2,
396 .port_ops = &cmd646r3_port_ops
397 },
398 { /* CMD 646U2 with working UDMA */
399 .flags = ATA_FLAG_SLAVE_POSS,
400 .pio_mask = ATA_PIO4,
401 .mwdma_mask = ATA_MWDMA2,
402 .udma_mask = ATA_UDMA2,
403 .port_ops = &cmd646r3_port_ops
404 },
405 { /* CMD 646 rev 1 */
406 .flags = ATA_FLAG_SLAVE_POSS,
407 .pio_mask = ATA_PIO4,
408 .mwdma_mask = ATA_MWDMA2,
409 .port_ops = &cmd646r1_port_ops
410 },
411 { /* CMD 648 */
412 .flags = ATA_FLAG_SLAVE_POSS,
413 .pio_mask = ATA_PIO4,
414 .mwdma_mask = ATA_MWDMA2,
415 .udma_mask = ATA_UDMA4,
416 .port_ops = &cmd648_port_ops
417 },
418 { /* CMD 649 */
419 .flags = ATA_FLAG_SLAVE_POSS,
420 .pio_mask = ATA_PIO4,
421 .mwdma_mask = ATA_MWDMA2,
422 .udma_mask = ATA_UDMA5,
423 .port_ops = &cmd648_port_ops
424 }
425 };
426 const struct ata_port_info *ppi[] = {
427 &cmd_info[id->driver_data],
428 &cmd_info[id->driver_data],
429 NULL
430 };
431 u8 reg;
432 int rc;
433 struct pci_dev *bridge = pdev->bus->self;
434 /* mobility split bridges don't report enabled ports correctly */
435 int port_ok = !(bridge && bridge->vendor ==
436 PCI_VENDOR_ID_MOBILITY_ELECTRONICS);
437 /* all (with exceptions below) apart from 643 have CNTRL_CH0 bit */
438 int cntrl_ch0_ok = (id->driver_data != 0);
439
440 rc = pcim_enable_device(pdev);
441 if (rc)
442 return rc;
443
444 if (id->driver_data == 0) /* 643 */
445 ata_pci_bmdma_clear_simplex(pdev);
446
447 if (pdev->device == PCI_DEVICE_ID_CMD_646)
448 switch (pdev->revision) {
449 /* UDMA works since rev 5 */
450 default:
451 ppi[0] = &cmd_info[3];
452 ppi[1] = &cmd_info[3];
453 break;
454 /* Interrupts in MRDMODE since rev 3 */
455 case 3:
456 case 4:
457 ppi[0] = &cmd_info[2];
458 ppi[1] = &cmd_info[2];
459 break;
460 /* Rev 1 with other problems? */
461 case 1:
462 ppi[0] = &cmd_info[4];
463 ppi[1] = &cmd_info[4];
464 fallthrough;
465 /* Early revs have no CNTRL_CH0 */
466 case 2:
467 case 0:
468 cntrl_ch0_ok = 0;
469 break;
470 }
471
472 cmd64x_fixup(pdev);
473
474 /* check for enabled ports */
475 pci_read_config_byte(pdev, CNTRL, ®);
476 if (!port_ok)
477 dev_notice(&pdev->dev, "Mobility Bridge detected, ignoring CNTRL port enable/disable\n");
478 if (port_ok && cntrl_ch0_ok && !(reg & CNTRL_CH0)) {
479 dev_notice(&pdev->dev, "Primary port is disabled\n");
480 ppi[0] = &ata_dummy_port_info;
481
482 }
483 if (port_ok && !(reg & CNTRL_CH1)) {
484 dev_notice(&pdev->dev, "Secondary port is disabled\n");
485 ppi[1] = &ata_dummy_port_info;
486 }
487
488 return ata_pci_bmdma_init_one(pdev, ppi, &cmd64x_sht, NULL, 0);
489 }
490
491 #ifdef CONFIG_PM_SLEEP
cmd64x_reinit_one(struct pci_dev * pdev)492 static int cmd64x_reinit_one(struct pci_dev *pdev)
493 {
494 struct ata_host *host = pci_get_drvdata(pdev);
495 int rc;
496
497 rc = ata_pci_device_do_resume(pdev);
498 if (rc)
499 return rc;
500
501 cmd64x_fixup(pdev);
502
503 ata_host_resume(host);
504 return 0;
505 }
506 #endif
507
508 static const struct pci_device_id cmd64x[] = {
509 { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_643), 0 },
510 { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_646), 1 },
511 { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_648), 5 },
512 { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_649), 6 },
513
514 { },
515 };
516
517 static struct pci_driver cmd64x_pci_driver = {
518 .name = DRV_NAME,
519 .id_table = cmd64x,
520 .probe = cmd64x_init_one,
521 .remove = ata_pci_remove_one,
522 #ifdef CONFIG_PM_SLEEP
523 .suspend = ata_pci_device_suspend,
524 .resume = cmd64x_reinit_one,
525 #endif
526 };
527
528 module_pci_driver(cmd64x_pci_driver);
529
530 MODULE_AUTHOR("Alan Cox");
531 MODULE_DESCRIPTION("low-level driver for CMD64x series PATA controllers");
532 MODULE_LICENSE("GPL");
533 MODULE_DEVICE_TABLE(pci, cmd64x);
534 MODULE_VERSION(DRV_VERSION);
535