1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2014-2016 Texas Instruments Incorporated - https://www.ti.com/
4 */
5/dts-v1/;
6
7#include "dra72x.dtsi"
8#include "dra7-ipu-dsp-common.dtsi"
9#include <dt-bindings/gpio/gpio.h>
10#include <dt-bindings/clock/ti-dra7-atl.h>
11
12/ {
13	compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
14
15	aliases {
16		display0 = &hdmi0;
17	};
18
19	chosen {
20		stdout-path = &uart1;
21	};
22
23	evm_12v0: fixedregulator-evm12v0 {
24		/* main supply */
25		compatible = "regulator-fixed";
26		regulator-name = "evm_12v0";
27		regulator-min-microvolt = <12000000>;
28		regulator-max-microvolt = <12000000>;
29		regulator-always-on;
30		regulator-boot-on;
31	};
32
33	evm_5v0: fixedregulator-evm5v0 {
34		/* Output 1 of TPS43351QDAPRQ1 on dra72-evm */
35		/* Output 1 of LM5140QRWGTQ1 on dra71-evm */
36		compatible = "regulator-fixed";
37		regulator-name = "evm_5v0";
38		regulator-min-microvolt = <5000000>;
39		regulator-max-microvolt = <5000000>;
40		vin-supply = <&evm_12v0>;
41		regulator-always-on;
42		regulator-boot-on;
43	};
44
45	evm_3v6: fixedregulator-evm_3v6 {
46		compatible = "regulator-fixed";
47		regulator-name = "evm_3v6";
48		regulator-min-microvolt = <3600000>;
49		regulator-max-microvolt = <3600000>;
50		vin-supply = <&evm_5v0>;
51		regulator-always-on;
52		regulator-boot-on;
53	};
54
55	vsys_3v3: fixedregulator-vsys3v3 {
56		/* Output 2 of TPS43351QDAPRQ1 on dra72-evm */
57		/* Output 2 of LM5140QRWGTQ1 on dra71-evm */
58		compatible = "regulator-fixed";
59		regulator-name = "vsys_3v3";
60		regulator-min-microvolt = <3300000>;
61		regulator-max-microvolt = <3300000>;
62		vin-supply = <&evm_12v0>;
63		regulator-always-on;
64		regulator-boot-on;
65	};
66
67	evm_3v3_sw: fixedregulator-evm_3v3 {
68		/* TPS22965DSG */
69		compatible = "regulator-fixed";
70		regulator-name = "evm_3v3";
71		regulator-min-microvolt = <3300000>;
72		regulator-max-microvolt = <3300000>;
73		vin-supply = <&vsys_3v3>;
74		regulator-always-on;
75		regulator-boot-on;
76	};
77
78	aic_dvdd: fixedregulator-aic_dvdd {
79		/* TPS77018DBVT */
80		compatible = "regulator-fixed";
81		regulator-name = "aic_dvdd";
82		vin-supply = <&evm_3v3_sw>;
83		regulator-min-microvolt = <1800000>;
84		regulator-max-microvolt = <1800000>;
85	};
86
87	evm_3v3_sd: fixedregulator-sd {
88		compatible = "regulator-fixed";
89		regulator-name = "evm_3v3_sd";
90		regulator-min-microvolt = <3300000>;
91		regulator-max-microvolt = <3300000>;
92		vin-supply = <&evm_3v3_sw>;
93		enable-active-high;
94		gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
95	};
96
97	extcon_usb1: extcon_usb1 {
98		compatible = "linux,extcon-usb-gpio";
99		id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
100	};
101
102	extcon_usb2: extcon_usb2 {
103		compatible = "linux,extcon-usb-gpio";
104		id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
105	};
106
107	hdmi0: connector {
108		compatible = "hdmi-connector";
109		label = "hdmi";
110
111		type = "a";
112
113		port {
114			hdmi_connector_in: endpoint {
115				remote-endpoint = <&tpd12s015_out>;
116			};
117		};
118	};
119
120	tpd12s015: encoder {
121		compatible = "ti,tpd12s015";
122
123		gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>,	/* P4, CT CP HPD */
124			<&pcf_hdmi 5 GPIO_ACTIVE_HIGH>,	/* P5, LS OE */
125			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
126
127		ports {
128			#address-cells = <1>;
129			#size-cells = <0>;
130
131			port@0 {
132				reg = <0>;
133
134				tpd12s015_in: endpoint {
135					remote-endpoint = <&hdmi_out>;
136				};
137			};
138
139			port@1 {
140				reg = <1>;
141
142				tpd12s015_out: endpoint {
143					remote-endpoint = <&hdmi_connector_in>;
144				};
145			};
146		};
147	};
148
149	sound0: sound0 {
150		compatible = "simple-audio-card";
151		simple-audio-card,name = "DRA7xx-EVM";
152		simple-audio-card,widgets =
153			"Headphone", "Headphone Jack",
154			"Line", "Line Out",
155			"Microphone", "Mic Jack",
156			"Line", "Line In";
157		simple-audio-card,routing =
158			"Headphone Jack",       "HPLOUT",
159			"Headphone Jack",       "HPROUT",
160			"Line Out",		"LLOUT",
161			"Line Out",		"RLOUT",
162			"MIC3L",		"Mic Jack",
163			"MIC3R",		"Mic Jack",
164			"Mic Jack",		"Mic Bias",
165			"LINE1L",               "Line In",
166			"LINE1R",               "Line In";
167		simple-audio-card,format = "dsp_b";
168		simple-audio-card,bitclock-master = <&sound0_master>;
169		simple-audio-card,frame-master = <&sound0_master>;
170		simple-audio-card,bitclock-inversion;
171
172		sound0_master: simple-audio-card,cpu {
173			sound-dai = <&mcasp3>;
174			system-clock-frequency = <5644800>;
175		};
176
177		simple-audio-card,codec {
178			sound-dai = <&tlv320aic3106>;
179			clocks = <&atl_clkin2_ck>;
180		};
181	};
182
183	vmmcwl_fixed: fixedregulator-mmcwl {
184		compatible = "regulator-fixed";
185		regulator-name = "vmmcwl_fixed";
186		regulator-min-microvolt = <1800000>;
187		regulator-max-microvolt = <1800000>;
188		gpio = <&gpio5 8 GPIO_ACTIVE_HIGH>;
189		enable-active-high;
190	};
191
192	clk_ov5640_fixed: clock {
193		compatible = "fixed-clock";
194		#clock-cells = <0>;
195		clock-frequency = <24000000>;
196	};
197};
198
199&dra7_pmx_core {
200	dcan1_pins_default: dcan1_pins_default {
201		pinctrl-single,pins = <
202			DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
203			DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1)	/* wakeup0.dcan1_rx */
204		>;
205	};
206
207	dcan1_pins_sleep: dcan1_pins_sleep {
208		pinctrl-single,pins = <
209			DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
210			DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP)	/* wakeup0.off */
211		>;
212	};
213};
214
215&i2c1 {
216	status = "okay";
217	clock-frequency = <400000>;
218
219	pcf_lcd: gpio@20 {
220		compatible = "nxp,pcf8575";
221		reg = <0x20>;
222		gpio-controller;
223		#gpio-cells = <2>;
224		interrupt-controller;
225		#interrupt-cells = <2>;
226	};
227
228	pcf_gpio_21: gpio@21 {
229		compatible = "ti,pcf8575", "nxp,pcf8575";
230		reg = <0x21>;
231		lines-initial-states = <0x1408>;
232		gpio-controller;
233		#gpio-cells = <2>;
234		interrupt-controller;
235		#interrupt-cells = <2>;
236	};
237
238	tlv320aic3106: tlv320aic3106@19 {
239		#sound-dai-cells = <0>;
240		compatible = "ti,tlv320aic3106";
241		reg = <0x19>;
242		adc-settle-ms = <40>;
243		ai3x-micbias-vg = <1>;		/* 2.0V */
244		status = "okay";
245
246		/* Regulators */
247		AVDD-supply = <&evm_3v3_sw>;
248		IOVDD-supply = <&evm_3v3_sw>;
249		DRVDD-supply = <&evm_3v3_sw>;
250		DVDD-supply = <&aic_dvdd>;
251	};
252};
253
254&i2c5 {
255	status = "okay";
256	clock-frequency = <400000>;
257
258	pcf_hdmi: pcf8575@26 {
259		compatible = "ti,pcf8575", "nxp,pcf8575";
260		reg = <0x26>;
261		gpio-controller;
262		#gpio-cells = <2>;
263		/*
264		 * initial state is used here to keep the mdio interface
265		 * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and
266		 * VIN2_S0 driven high otherwise Ethernet stops working
267		 * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
268		 */
269		lines-initial-states = <0x0f2b>;
270
271		p1 {
272			/* vin6_sel_s0: high: VIN6, low: audio */
273			gpio-hog;
274			gpios = <1 GPIO_ACTIVE_HIGH>;
275			output-low;
276			line-name = "vin6_sel_s0";
277		};
278	};
279
280	ov5640@3c {
281		compatible = "ovti,ov5640";
282		reg = <0x3c>;
283
284		clocks = <&clk_ov5640_fixed>;
285		clock-names = "xclk";
286
287		port {
288			csi2_cam0: endpoint {
289				remote-endpoint = <&csi2_phy0>;
290				clock-lanes = <0>;
291				data-lanes = <1 2>;
292			};
293		};
294	};
295
296};
297
298&uart1 {
299	status = "okay";
300	interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
301			      <&dra7_pmx_core 0x3e0>;
302};
303
304&elm {
305	status = "okay";
306};
307
308&gpmc {
309	/*
310	 * For the existing IOdelay configuration via U-Boot we don't
311	 * support NAND on dra72-evm. Keep it disabled. Enabling it
312	 * requires a different configuration by U-Boot.
313	 */
314	status = "disabled";
315	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
316	nand@0,0 {
317		/* To use NAND, DIP switch SW5 must be set like so:
318		 * SW5.1 (NAND_SELn) = ON (LOW)
319		 * SW5.9 (GPMC_WPN) = OFF (HIGH)
320		 */
321		compatible = "ti,omap2-nand";
322		reg = <0 0 4>;		/* device IO registers */
323		interrupt-parent = <&gpmc>;
324		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
325			     <1 IRQ_TYPE_NONE>;	/* termcount */
326		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
327		ti,nand-xfer-type = "prefetch-dma";
328		ti,nand-ecc-opt = "bch8";
329		ti,elm-id = <&elm>;
330		nand-bus-width = <16>;
331		gpmc,device-width = <2>;
332		gpmc,sync-clk-ps = <0>;
333		gpmc,cs-on-ns = <0>;
334		gpmc,cs-rd-off-ns = <80>;
335		gpmc,cs-wr-off-ns = <80>;
336		gpmc,adv-on-ns = <0>;
337		gpmc,adv-rd-off-ns = <60>;
338		gpmc,adv-wr-off-ns = <60>;
339		gpmc,we-on-ns = <10>;
340		gpmc,we-off-ns = <50>;
341		gpmc,oe-on-ns = <4>;
342		gpmc,oe-off-ns = <40>;
343		gpmc,access-ns = <40>;
344		gpmc,wr-access-ns = <80>;
345		gpmc,rd-cycle-ns = <80>;
346		gpmc,wr-cycle-ns = <80>;
347		gpmc,bus-turnaround-ns = <0>;
348		gpmc,cycle2cycle-delay-ns = <0>;
349		gpmc,clk-activation-ns = <0>;
350		gpmc,wr-data-mux-bus-ns = <0>;
351		/* MTD partition table */
352		/* All SPL-* partitions are sized to minimal length
353		 * which can be independently programmable. For
354		 * NAND flash this is equal to size of erase-block */
355		#address-cells = <1>;
356		#size-cells = <1>;
357		partition@0 {
358			label = "NAND.SPL";
359			reg = <0x00000000 0x000020000>;
360		};
361		partition@1 {
362			label = "NAND.SPL.backup1";
363			reg = <0x00020000 0x00020000>;
364		};
365		partition@2 {
366			label = "NAND.SPL.backup2";
367			reg = <0x00040000 0x00020000>;
368		};
369		partition@3 {
370			label = "NAND.SPL.backup3";
371			reg = <0x00060000 0x00020000>;
372		};
373		partition@4 {
374			label = "NAND.u-boot-spl-os";
375			reg = <0x00080000 0x00040000>;
376		};
377		partition@5 {
378			label = "NAND.u-boot";
379			reg = <0x000c0000 0x00100000>;
380		};
381		partition@6 {
382			label = "NAND.u-boot-env";
383			reg = <0x001c0000 0x00020000>;
384		};
385		partition@7 {
386			label = "NAND.u-boot-env.backup1";
387			reg = <0x001e0000 0x00020000>;
388		};
389		partition@8 {
390			label = "NAND.kernel";
391			reg = <0x00200000 0x00800000>;
392		};
393		partition@9 {
394			label = "NAND.file-system";
395			reg = <0x00a00000 0x0f600000>;
396		};
397	};
398};
399
400&omap_dwc3_1 {
401	extcon = <&extcon_usb1>;
402};
403
404&omap_dwc3_2 {
405	extcon = <&extcon_usb2>;
406};
407
408&usb1 {
409	dr_mode = "otg";
410	extcon = <&extcon_usb1>;
411};
412
413&usb2 {
414	dr_mode = "host";
415	extcon = <&extcon_usb2>;
416};
417
418&mmc1 {
419	status = "okay";
420	pinctrl-names = "default";
421	pinctrl-0 = <&mmc1_pins_default>;
422	vmmc-supply = <&evm_3v3_sd>;
423	bus-width = <4>;
424	/*
425	 * SDCD signal is not being used here - using the fact that GPIO mode
426	 * is a viable alternative
427	 */
428	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
429	max-frequency = <192000000>;
430};
431
432&mmc2 {
433	/* SW5-3 in ON position */
434	status = "okay";
435	pinctrl-names = "default";
436	pinctrl-0 = <&mmc2_pins_default>;
437	bus-width = <8>;
438	non-removable;
439	max-frequency = <192000000>;
440};
441
442&mmc4 {
443	status = "okay";
444	vmmc-supply = <&evm_3v6>;
445	vqmmc-supply = <&vmmcwl_fixed>;
446	bus-width = <4>;
447	cap-power-off-card;
448	keep-power-in-suspend;
449	non-removable;
450	pinctrl-names = "default", "hs", "sdr12", "sdr25";
451	pinctrl-0 = <&mmc4_pins_default>;
452	pinctrl-1 = <&mmc4_pins_default>;
453	pinctrl-2 = <&mmc4_pins_default>;
454	pinctrl-3 = <&mmc4_pins_default>;
455	#address-cells = <1>;
456	#size-cells = <0>;
457	wifi@2 {
458		compatible = "ti,wl1835";
459		reg = <2>;
460		interrupt-parent = <&gpio5>;
461		interrupts = <7 IRQ_TYPE_EDGE_RISING>;
462	};
463};
464
465&dcan1 {
466	status = "okay";
467	pinctrl-names = "default", "sleep", "active";
468	pinctrl-0 = <&dcan1_pins_sleep>;
469	pinctrl-1 = <&dcan1_pins_sleep>;
470	pinctrl-2 = <&dcan1_pins_default>;
471};
472
473&qspi {
474	status = "okay";
475
476	spi-max-frequency = <76800000>;
477	m25p80@0 {
478		compatible = "s25fl256s1";
479		spi-max-frequency = <76800000>;
480		reg = <0>;
481		spi-tx-bus-width = <1>;
482		spi-rx-bus-width = <4>;
483		#address-cells = <1>;
484		#size-cells = <1>;
485
486		/* MTD partition table.
487		 * The ROM checks the first four physical blocks
488		 * for a valid file to boot and the flash here is
489		 * 64KiB block size.
490		 */
491		partition@0 {
492			label = "QSPI.SPL";
493			reg = <0x00000000 0x000010000>;
494		};
495		partition@1 {
496			label = "QSPI.SPL.backup1";
497			reg = <0x00010000 0x00010000>;
498		};
499		partition@2 {
500			label = "QSPI.SPL.backup2";
501			reg = <0x00020000 0x00010000>;
502		};
503		partition@3 {
504			label = "QSPI.SPL.backup3";
505			reg = <0x00030000 0x00010000>;
506		};
507		partition@4 {
508			label = "QSPI.u-boot";
509			reg = <0x00040000 0x00100000>;
510		};
511		partition@5 {
512			label = "QSPI.u-boot-spl-os";
513			reg = <0x00140000 0x00080000>;
514		};
515		partition@6 {
516			label = "QSPI.u-boot-env";
517			reg = <0x001c0000 0x00010000>;
518		};
519		partition@7 {
520			label = "QSPI.u-boot-env.backup1";
521			reg = <0x001d0000 0x0010000>;
522		};
523		partition@8 {
524			label = "QSPI.kernel";
525			reg = <0x001e0000 0x0800000>;
526		};
527		partition@9 {
528			label = "QSPI.file-system";
529			reg = <0x009e0000 0x01620000>;
530		};
531	};
532};
533
534&dss {
535	status = "okay";
536};
537
538&hdmi {
539	status = "okay";
540
541	port {
542		hdmi_out: endpoint {
543			remote-endpoint = <&tpd12s015_in>;
544		};
545	};
546};
547
548&atl {
549	assigned-clocks = <&abe_dpll_sys_clk_mux>,
550			  <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>,
551			  <&dpll_abe_ck>,
552			  <&dpll_abe_m2x2_ck>,
553			  <&atl_clkin2_ck>;
554	assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>;
555	assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>;
556
557	status = "okay";
558
559	atl2 {
560		bws = <DRA7_ATL_WS_MCASP2_FSX>;
561		aws = <DRA7_ATL_WS_MCASP3_FSX>;
562	};
563};
564
565&mcasp3 {
566	#sound-dai-cells = <0>;
567
568	assigned-clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
569	assigned-clock-parents = <&atl_clkin2_ck>;
570
571	status = "okay";
572
573	op-mode = <0>;          /* MCASP_IIS_MODE */
574	tdm-slots = <2>;
575	/* 4 serializer */
576	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
577		1 2 0 0
578	>;
579	tx-num-evt = <32>;
580	rx-num-evt = <32>;
581};
582
583&pcie1_rc {
584	status = "okay";
585};
586
587&csi2_0 {
588	csi2_phy0: endpoint {
589		remote-endpoint = <&csi2_cam0>;
590		clock-lanes = <0>;
591		data-lanes = <1 2>;
592	};
593};
594