1// SPDX-License-Identifier: GPL-2.0
2/dts-v1/;
3
4#include "kirkwood.dtsi"
5#include "kirkwood-6281.dtsi"
6
7/ {
8	model = "Seagate GoFlex Net";
9	compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood";
10
11	memory {
12		device_type = "memory";
13		reg = <0x00000000 0x8000000>;
14	};
15
16	chosen {
17		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
18		stdout-path = &uart0;
19	};
20
21	ocp@f1000000 {
22		pinctrl: pin-controller@10000 {
23			pmx_usb_power_enable: pmx-usb-power-enable {
24				marvell,pins = "mpp29";
25				marvell,function = "gpio";
26			};
27			pmx_led_right_cap_0: pmx-led_right_cap_0 {
28				marvell,pins = "mpp38";
29				marvell,function = "gpio";
30			};
31			pmx_led_right_cap_1: pmx-led_right_cap_1 {
32				marvell,pins = "mpp39";
33				marvell,function = "gpio";
34			};
35			pmx_led_right_cap_2: pmx-led_right_cap_2 {
36				marvell,pins = "mpp40";
37				marvell,function = "gpio";
38			};
39			pmx_led_right_cap_3: pmx-led_right_cap_3 {
40				marvell,pins = "mpp41";
41				marvell,function = "gpio";
42			};
43			pmx_led_left_cap_0: pmx-led_left_cap_0 {
44				marvell,pins = "mpp42";
45				marvell,function = "gpio";
46			};
47			pmx_led_left_cap_1: pmx-led_left_cap_1 {
48				marvell,pins = "mpp43";
49				marvell,function = "gpio";
50			};
51			pmx_led_left_cap_2: pmx-led_left_cap_2 {
52				marvell,pins = "mpp44";
53				marvell,function = "gpio";
54			};
55			pmx_led_left_cap_3: pmx-led_left_cap_3 {
56				marvell,pins = "mpp45";
57				marvell,function = "gpio";
58			};
59			pmx_led_green: pmx-led_green {
60				marvell,pins = "mpp46";
61				marvell,function = "gpio";
62			};
63			pmx_led_orange: pmx-led_orange {
64				marvell,pins = "mpp47";
65				marvell,function = "gpio";
66			};
67		};
68		serial@12000 {
69			status = "okay";
70		};
71
72		sata@80000 {
73			status = "okay";
74			nr-ports = <2>;
75		};
76
77	};
78	gpio-leds {
79		compatible = "gpio-leds";
80		pinctrl-0 = < &pmx_led_orange
81			      &pmx_led_left_cap_0 &pmx_led_left_cap_1
82			      &pmx_led_left_cap_2 &pmx_led_left_cap_3
83			      &pmx_led_right_cap_0 &pmx_led_right_cap_1
84			      &pmx_led_right_cap_2 &pmx_led_right_cap_3
85			    >;
86		pinctrl-names = "default";
87
88		health {
89			label = "status:green:health";
90			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
91			default-state = "keep";
92		};
93		fault {
94			label = "status:orange:fault";
95			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
96		};
97		left0 {
98			label = "status:white:left0";
99			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
100		};
101		left1 {
102			label = "status:white:left1";
103			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
104		};
105		left2 {
106			label = "status:white:left2";
107			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
108		};
109		left3 {
110			label = "status:white:left3";
111			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
112		};
113		right0 {
114			label = "status:white:right0";
115			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
116		};
117		right1 {
118			label = "status:white:right1";
119			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
120		};
121		right2 {
122			label = "status:white:right2";
123			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
124		};
125		right3 {
126			label = "status:white:right3";
127			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
128		};
129	};
130	regulators {
131		compatible = "simple-bus";
132		#address-cells = <1>;
133		#size-cells = <0>;
134		pinctrl-0 = <&pmx_usb_power_enable>;
135		pinctrl-names = "default";
136
137		usb_power: regulator@1 {
138			compatible = "regulator-fixed";
139			reg = <1>;
140			regulator-name = "USB Power";
141			regulator-min-microvolt = <5000000>;
142			regulator-max-microvolt = <5000000>;
143			enable-active-high;
144			regulator-always-on;
145			regulator-boot-on;
146			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
147		};
148	};
149};
150
151&nand {
152	chip-delay = <40>;
153	status = "okay";
154
155	partition@0 {
156		label = "u-boot";
157		reg = <0x0000000 0x100000>;
158		read-only;
159	};
160
161	partition@100000 {
162		label = "uImage";
163		reg = <0x0100000 0x400000>;
164	};
165
166	partition@500000 {
167		label = "pogoplug";
168		reg = <0x0500000 0x2000000>;
169	};
170
171	partition@2500000 {
172		label = "root";
173		reg = <0x02500000 0xd800000>;
174	};
175};
176
177&mdio {
178	status = "okay";
179
180	ethphy0: ethernet-phy@0 {
181		reg = <0>;
182	};
183};
184
185&eth0 {
186	status = "okay";
187	ethernet0-port@0 {
188		phy-handle = <&ethphy0>;
189	};
190};
191