1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Support for CompuLab CM-T54
4 */
5/dts-v1/;
6
7#include "omap5.dtsi"
8#include <dt-bindings/interrupt-controller/irq.h>
9#include <dt-bindings/interrupt-controller/arm-gic.h>
10
11/ {
12	model = "CompuLab CM-T54";
13	compatible = "compulab,omap5-cm-t54", "ti,omap5";
14
15	memory@80000000 {
16		device_type = "memory";
17		reg = <0 0x80000000 0 0x7f000000>; /* 2048 MB */
18	};
19
20	aliases {
21		display0 = &hdmi0;
22		display1 = &dvi0;
23		display2 = &lcd0;
24	};
25
26	vmmcsd_fixed: fixed-regulator-mmcsd {
27		compatible = "regulator-fixed";
28		regulator-name = "vmmcsd_fixed";
29		regulator-min-microvolt = <3300000>;
30		regulator-max-microvolt = <3300000>;
31	};
32
33	vwlan_pdn_fixed: fixed-regulator-vwlan-pdn {
34		compatible = "regulator-fixed";
35		regulator-name = "vwlan_pdn_fixed";
36		regulator-min-microvolt = <3300000>;
37		regulator-max-microvolt = <3300000>;
38		vin-supply = <&ldo2_reg>;
39		gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>;   /* gpio4_109 */
40		startup-delay-us = <1000>;
41		enable-active-high;
42	};
43
44	vwlan_fixed: fixed-regulator-vwlan {
45		compatible = "regulator-fixed";
46		regulator-name = "vwlan_fixed";
47		regulator-min-microvolt = <3300000>;
48		regulator-max-microvolt = <3300000>;
49		vin-supply = <&vwlan_pdn_fixed>;
50		gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>;   /* gpio4_110 */
51		startup-delay-us = <1000>;
52		enable-active-high;
53	};
54
55	ads7846reg: ads7846-reg {
56		compatible = "regulator-fixed";
57		regulator-name = "ads7846-reg";
58		regulator-min-microvolt = <3300000>;
59		regulator-max-microvolt = <3300000>;
60	};
61
62	/* HS USB Host PHY on PORT 2 */
63	hsusb2_phy: hsusb2_phy {
64		compatible = "usb-nop-xceiv";
65		reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
66		#phy-cells = <0>;
67	};
68
69	/* HS USB Host PHY on PORT 3 */
70	hsusb3_phy: hsusb3_phy {
71		compatible = "usb-nop-xceiv";
72		reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
73		#phy-cells = <0>;
74	};
75
76	leds {
77		compatible = "gpio-leds";
78		led1 {
79			label = "Heartbeat";
80			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */
81			linux,default-trigger = "heartbeat";
82			default-state = "off";
83		};
84	};
85
86	lcd0: display {
87                compatible = "startek,startek-kd050c", "panel-dpi";
88                label = "lcd";
89
90                pinctrl-names = "default";
91                pinctrl-0 = <&lcd_pins>;
92
93                enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
94
95                panel-timing {
96                        clock-frequency = <33000000>;
97                        hactive = <800>;
98                        vactive = <480>;
99                        hfront-porch = <40>;
100                        hback-porch = <40>;
101                        hsync-len = <43>;
102                        vback-porch = <29>;
103                        vfront-porch = <13>;
104                        vsync-len = <3>;
105                        hsync-active = <0>;
106                        vsync-active = <0>;
107                        de-active = <1>;
108                        pixelclk-active = <1>;
109                };
110
111                port {
112                        lcd_in: endpoint {
113                                remote-endpoint = <&dpi_lcd_out>;
114                        };
115                };
116        };
117
118	hdmi0: connector0 {
119		compatible = "hdmi-connector";
120		label = "hdmi";
121
122		type = "a";
123
124		pinctrl-names = "default";
125		pinctrl-0 = <&hdmi_conn_pins>;
126
127		hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */
128
129		port {
130			hdmi_connector_in: endpoint {
131				remote-endpoint = <&hdmi_out>;
132			};
133		};
134	};
135
136	tfp410: encoder0 {
137		compatible = "ti,tfp410";
138
139		ports {
140			#address-cells = <1>;
141			#size-cells = <0>;
142
143			port@0 {
144				reg = <0>;
145
146				tfp410_in: endpoint {
147					remote-endpoint = <&dpi_dvi_out>;
148				};
149			};
150
151			port@1 {
152				reg = <1>;
153
154				tfp410_out: endpoint {
155					remote-endpoint = <&dvi_connector_in>;
156				};
157			};
158		};
159	};
160
161	dvi0: connector1 {
162		compatible = "dvi-connector";
163		label = "dvi";
164
165		digital;
166
167		ddc-i2c-bus = <&i2c2>;
168
169		port {
170			dvi_connector_in: endpoint {
171				remote-endpoint = <&tfp410_out>;
172			};
173		};
174	};
175};
176
177&omap5_pmx_wkup {
178
179	ads7846_pins: pinmux_ads7846_pins {
180		pinctrl-single,pins = <
181			OMAP5_IOPAD(0x0042, PIN_INPUT_PULLDOWN | MUX_MODE6)  /* llib_wakereqin.gpio1_wk15 */
182		>;
183	};
184
185	palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins {
186		pinctrl-single,pins = <
187			/* sys_nirq1 is pulled down as the SoC is inverting it for GIC */
188			OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0)
189		>;
190	};
191};
192
193&omap5_pmx_core {
194	pinctrl-names = "default";
195	pinctrl-0 = <
196			&led_gpio_pins
197			&usbhost_pins
198	>;
199
200	led_gpio_pins: pinmux_led_gpio_pins {
201		pinctrl-single,pins = <
202			OMAP5_IOPAD(0x00b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */
203		>;
204	};
205
206	i2c1_pins: pinmux_i2c1_pins {
207		pinctrl-single,pins = <
208			OMAP5_IOPAD(0x01f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */
209			OMAP5_IOPAD(0x01f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */
210		>;
211	};
212
213	i2c2_pins: pinmux_i2c2_pins {
214		pinctrl-single,pins = <
215			OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
216			OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
217		>;
218	};
219
220	mmc1_pins: pinmux_mmc1_pins {
221		pinctrl-single,pins = <
222			OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
223			OMAP5_IOPAD(0x01e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */
224			OMAP5_IOPAD(0x01e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */
225			OMAP5_IOPAD(0x01e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */
226			OMAP5_IOPAD(0x01ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */
227			OMAP5_IOPAD(0x01ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */
228		>;
229	};
230
231	mmc2_pins: pinmux_mmc2_pins {
232		pinctrl-single,pins = <
233			OMAP5_IOPAD(0x0040, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */
234			OMAP5_IOPAD(0x0042, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */
235			OMAP5_IOPAD(0x0044, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */
236			OMAP5_IOPAD(0x0046, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */
237			OMAP5_IOPAD(0x0048, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */
238			OMAP5_IOPAD(0x004a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */
239			OMAP5_IOPAD(0x004c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */
240			OMAP5_IOPAD(0x004e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */
241			OMAP5_IOPAD(0x0050, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */
242			OMAP5_IOPAD(0x0052, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */
243		>;
244	};
245
246	mmc3_pins: pinmux_mmc3_pins {
247		pinctrl-single,pins = <
248			OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
249			OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
250			OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
251			OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
252			OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
253			OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
254		>;
255	};
256
257	wlan_gpios_pins: pinmux_wlan_gpios_pins {
258		pinctrl-single,pins = <
259			OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */
260			OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */
261		>;
262	};
263
264	usbhost_pins: pinmux_usbhost_pins {
265		pinctrl-single,pins = <
266			OMAP5_IOPAD(0x00c4, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_strobe */
267			OMAP5_IOPAD(0x00c6, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_data */
268
269			OMAP5_IOPAD(0x01dc, PIN_INPUT | MUX_MODE0)  /* usbb3_hsic_strobe */
270			OMAP5_IOPAD(0x01de, PIN_INPUT | MUX_MODE0)  /* usbb3_hsic_data */
271
272			OMAP5_IOPAD(0x00a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */
273			OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */
274		>;
275	};
276
277	dss_hdmi_pins: pinmux_dss_hdmi_pins {
278		pinctrl-single,pins = <
279			OMAP5_IOPAD(0x013c, PIN_INPUT | MUX_MODE0) /* hdmi_cec */
280			OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */
281			OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */
282		>;
283	};
284
285	lcd_pins: pinmux_lcd_pins {
286		pinctrl-single,pins = <
287			OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */
288		>;
289	};
290
291	hdmi_conn_pins: pinmux_hdmi_conn_pins {
292		pinctrl-single,pins = <
293			OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
294		>;
295	};
296
297	dss_dpi_pins: pinmux_dss_dpi_pins {
298		pinctrl-single,pins = <
299			OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */
300			OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */
301			OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* rfbi_data13.dispc_data13 */
302			OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data12.dispc_data12 */
303			OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data11.dispc_data11 */
304			OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data10.dispc_data10 */
305			OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* rfbi_data9.dispc_data9 */
306			OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* rfbi_data8.dispc_data8 */
307			OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* rfbi_data7.dispc_data7 */
308			OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* rfbi_data6.dispc_data6 */
309			OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* rfbi_data5.dispc_data5 */
310			OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data4.dispc_data4 */
311			OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data3.dispc_data3 */
312			OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data2.dispc_data2 */
313			OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* rfbi_data1.dispc_data1 */
314			OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* rfbi_data0.dispc_data0 */
315			OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* rfbi_we.dispc_vsync */
316			OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* rfbi_cs0.dispc_hsync */
317			OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* rfbi_a0.dispc_de */
318			OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* rfbi_re.dispc_pclk */
319			OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* rfbi_hsync0.dispc_data17 */
320			OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* rfbi_te_vsync0.dispc_data16 */
321			OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* gpio6_182.dispc_data18 */
322			OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* gpio6_183.dispc_data19 */
323			OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* gpio6_184.dispc_data20 */
324			OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* gpio6_185.dispc_data21 */
325			OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* gpio6_186.dispc_data22 */
326			OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */
327		>;
328	};
329
330	mcspi2_pins: pinmux_mcspi1_pins {
331		pinctrl-single,pins = <
332			OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
333			OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
334			OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi */
335			OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0 */
336		>;
337	};
338};
339
340&mcspi2 {
341	pinctrl-names = "default";
342	pinctrl-0 = <&mcspi2_pins>;
343
344	/* touch controller */
345	ads7846@0 {
346		pinctrl-names = "default";
347		pinctrl-0 = <&ads7846_pins>;
348
349		compatible = "ti,ads7846";
350		vcc-supply = <&ads7846reg>;
351
352		reg = <0>;				/* CS0 */
353		spi-max-frequency = <1500000>;
354
355		interrupt-parent = <&gpio1>;
356		interrupts = <15 0>;			/* gpio1_wk15 */
357		pendown-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
358
359
360		ti,x-min = /bits/ 16 <0x0>;
361		ti,x-max = /bits/ 16 <0x0fff>;
362		ti,y-min = /bits/ 16 <0x0>;
363		ti,y-max = /bits/ 16 <0x0fff>;
364
365		ti,x-plate-ohms = /bits/ 16 <180>;
366		ti,pressure-max = /bits/ 16 <255>;
367
368		ti,debounce-max = /bits/ 16 <30>;
369		ti,debounce-tol = /bits/ 16 <10>;
370		ti,debounce-rep = /bits/ 16 <1>;
371
372		wakeup-source;
373	};
374};
375
376&mmc1 {
377	pinctrl-names = "default";
378	pinctrl-0 = <&mmc1_pins>;
379	vmmc-supply = <&ldo9_reg>;
380	bus-width = <4>;
381};
382
383&mmc2 {
384	pinctrl-names = "default";
385	pinctrl-0 = <&mmc2_pins>;
386	vmmc-supply = <&vmmcsd_fixed>;
387	bus-width = <8>;
388	ti,non-removable;
389};
390
391&mmc3 {
392	pinctrl-names = "default";
393	pinctrl-0 = <
394		&mmc3_pins
395		&wlan_gpios_pins
396	>;
397	vmmc-supply = <&vwlan_fixed>;
398	bus-width = <4>;
399	ti,non-removable;
400};
401
402&mmc4 {
403	status = "disabled";
404};
405
406&mmc5 {
407	status = "disabled";
408};
409
410&i2c1 {
411	pinctrl-names = "default";
412	pinctrl-0 = <&i2c1_pins>;
413
414	clock-frequency = <400000>;
415
416	at24@50 {
417		compatible = "atmel,24c02";
418		pagesize = <16>;
419		reg = <0x50>;
420	};
421
422	palmas: palmas@48 {
423		compatible = "ti,palmas";
424		reg = <0x48>;
425		pinctrl-0 = <&palmas_sys_nirq_pins>;
426		pinctrl-names = "default";
427		/* sys_nirq/ext_sys_irq pins get inverted at mpuss wakeupgen */
428		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_LOW>;
429		interrupt-controller;
430		#interrupt-cells = <2>;
431		ti,system-power-controller;
432
433		extcon_usb3: palmas_usb {
434			compatible = "ti,palmas-usb-vid";
435			ti,enable-vbus-detection;
436			ti,enable-id-detection;
437			ti,wakeup;
438		};
439
440		rtc {
441			compatible = "ti,palmas-rtc";
442			interrupt-parent = <&palmas>;
443			interrupts = <8 IRQ_TYPE_NONE>;
444		};
445
446		palmas_pmic {
447			compatible = "ti,palmas-pmic";
448			interrupt-parent = <&palmas>;
449			interrupts = <14 IRQ_TYPE_NONE>;
450			interrupt-names = "short-irq";
451
452			ti,ldo6-vibrator;
453
454			regulators {
455				smps123_reg: smps123 {
456					/* VDD_OPP_MPU */
457					regulator-name = "smps123";
458					regulator-min-microvolt = < 600000>;
459					regulator-max-microvolt = <1500000>;
460					regulator-always-on;
461					regulator-boot-on;
462				};
463
464				smps45_reg: smps45 {
465					/* VDD_OPP_MM */
466					regulator-name = "smps45";
467					regulator-min-microvolt = < 600000>;
468					regulator-max-microvolt = <1310000>;
469					regulator-always-on;
470					regulator-boot-on;
471				};
472
473				smps6_reg: smps6 {
474					/* VDD_DDR3 - over VDD_SMPS6 */
475					regulator-name = "smps6";
476					regulator-min-microvolt = <1500000>;
477					regulator-max-microvolt = <1500000>;
478					regulator-always-on;
479					regulator-boot-on;
480				};
481
482				smps7_reg: smps7 {
483					/* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
484					regulator-name = "smps7";
485					regulator-min-microvolt = <1800000>;
486					regulator-max-microvolt = <1800000>;
487					regulator-always-on;
488					regulator-boot-on;
489				};
490
491				smps8_reg: smps8 {
492					/* VDD_OPP_CORE */
493					regulator-name = "smps8";
494					regulator-min-microvolt = < 600000>;
495					regulator-max-microvolt = <1310000>;
496					regulator-always-on;
497					regulator-boot-on;
498				};
499
500				smps9_reg: smps9 {
501					/* VDDA_2v1_AUD over VDD_2v1 */
502					regulator-name = "smps9";
503					regulator-min-microvolt = <3300000>;
504					regulator-max-microvolt = <3300000>;
505					ti,smps-range = <0x80>;
506					regulator-always-on;
507					regulator-boot-on;
508				};
509
510				smps10_out2_reg: smps10_out2 {
511					/* VBUS_5V_OTG */
512					regulator-name = "smps10_out2";
513					regulator-min-microvolt = <5000000>;
514					regulator-max-microvolt = <5000000>;
515					regulator-always-on;
516					regulator-boot-on;
517				};
518
519				smps10_out1_reg: smps10_out1 {
520					/* VBUS_5V_OTG */
521					regulator-name = "smps10_out1";
522					regulator-min-microvolt = <5000000>;
523					regulator-max-microvolt = <5000000>;
524				};
525
526				ldo1_reg: ldo1 {
527					/* VDDAPHY_CAM: vdda_csiport */
528					regulator-name = "ldo1";
529					regulator-min-microvolt = <1800000>;
530					regulator-max-microvolt = <1800000>;
531				};
532
533				ldo2_reg: ldo2 {
534					/* VDD_3V3_WLAN */
535					regulator-name = "ldo2";
536					regulator-min-microvolt = <3300000>;
537					regulator-max-microvolt = <3300000>;
538					startup-delay-us = <1000>;
539				};
540
541				ldo3_reg: ldo3 {
542					/* VCC_1V5_AUD */
543					regulator-name = "ldo3";
544					regulator-min-microvolt = <1500000>;
545					regulator-max-microvolt = <1500000>;
546					regulator-always-on;
547					regulator-boot-on;
548				};
549
550				ldo4_reg: ldo4 {
551					/* VDDAPHY_DISP: vdda_dsiport/hdmi */
552					regulator-name = "ldo4";
553					regulator-min-microvolt = <1800000>;
554					regulator-max-microvolt = <1800000>;
555				};
556
557				ldo5_reg: ldo5 {
558					/* VDDA_1V8_PHY: usb/sata/hdmi.. */
559					regulator-name = "ldo5";
560					regulator-min-microvolt = <1800000>;
561					regulator-max-microvolt = <1800000>;
562					regulator-always-on;
563					regulator-boot-on;
564				};
565
566				ldo6_reg: ldo6 {
567					/* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
568					regulator-name = "ldo6";
569					regulator-min-microvolt = <1200000>;
570					regulator-max-microvolt = <1200000>;
571					regulator-always-on;
572					regulator-boot-on;
573				};
574
575				ldo7_reg: ldo7 {
576					/* VDD_VPP: vpp1 */
577					regulator-name = "ldo7";
578					regulator-min-microvolt = <2000000>;
579					regulator-max-microvolt = <2000000>;
580					/* Only for efuse reprograming! */
581					status = "disabled";
582				};
583
584				ldo8_reg: ldo8 {
585					/* VDD_3V_GP: act led/serial console */
586					regulator-name = "ldo8";
587					regulator-min-microvolt = <3000000>;
588					regulator-max-microvolt = <3000000>;
589					regulator-always-on;
590					regulator-boot-on;
591				};
592
593				ldo9_reg: ldo9 {
594					/* VCC_DV_SDIO: vdds_sdcard */
595					regulator-name = "ldo9";
596					regulator-min-microvolt = <1800000>;
597					regulator-max-microvolt = <3000000>;
598					regulator-boot-on;
599				};
600
601				ldoln_reg: ldoln {
602					/* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
603					regulator-name = "ldoln";
604					regulator-min-microvolt = <1800000>;
605					regulator-max-microvolt = <1800000>;
606					regulator-always-on;
607					regulator-boot-on;
608				};
609
610				ldousb_reg: ldousb {
611					/* VDDA_3V_USB: VDDA_USBHS33 */
612					regulator-name = "ldousb";
613					regulator-min-microvolt = <3250000>;
614					regulator-max-microvolt = <3250000>;
615					regulator-always-on;
616					regulator-boot-on;
617				};
618
619				regen3_reg: regen3 {
620					/* REGEN3 controls LDO9 supply to card */
621					regulator-name = "regen3";
622					regulator-always-on;
623					regulator-boot-on;
624				};
625			};
626		};
627	};
628};
629
630&i2c2 {
631	pinctrl-names = "default";
632	pinctrl-0 = <&i2c2_pins>;
633
634	clock-frequency = <100000>;
635};
636
637&usbhshost {
638	port2-mode = "ehci-hsic";
639	port3-mode = "ehci-hsic";
640};
641
642&usbhsehci {
643	phys = <0 &hsusb2_phy &hsusb3_phy>;
644};
645
646&usb3 {
647       extcon = <&extcon_usb3>;
648       vbus-supply = <&smps10_out1_reg>;
649};
650
651&cpu0 {
652	cpu0-supply = <&smps123_reg>;
653};
654
655&dss {
656	status = "okay";
657
658	pinctrl-names = "default";
659	pinctrl-0 = <&dss_dpi_pins>;
660
661	port {
662		#address-cells = <1>;
663		#size-cells = <0>;
664
665		dpi_dvi_out: endpoint@0 {
666			reg = <0>;
667			remote-endpoint = <&tfp410_in>;
668			data-lines = <24>;
669		};
670
671		dpi_lcd_out: endpoint@1 {
672			reg = <1>;
673			remote-endpoint = <&lcd_in>;
674			data-lines = <24>;
675		};
676	};
677};
678
679&dsi2 {
680	status = "okay";
681	vdd-supply = <&ldo4_reg>;
682};
683
684&hdmi {
685	status = "okay";
686	vdda-supply = <&ldo4_reg>;
687
688	pinctrl-names = "default";
689	pinctrl-0 = <&dss_hdmi_pins>;
690
691	port {
692		hdmi_out: endpoint {
693			remote-endpoint = <&hdmi_connector_in>;
694			lanes = <1 0 3 2 5 4 7 6>;
695		};
696	};
697};
698