1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 * TW5864 driver - registers description 4 * 5 * Copyright (C) 2016 Bluecherry, LLC <maintainers@bluecherrydvr.com> 6 */ 7 8 /* According to TW5864_datasheet_0.6d.pdf, tw5864b1-ds.pdf */ 9 10 /* Register Description - Direct Map Space */ 11 /* 0x0000 ~ 0x1ffc - H264 Register Map */ 12 /* [15:0] The Version register for H264 core (Read Only) */ 13 #define TW5864_H264REV 0x0000 14 15 #define TW5864_EMU 0x0004 16 /* Define controls in register TW5864_EMU */ 17 /* DDR controller enabled */ 18 #define TW5864_EMU_EN_DDR BIT(0) 19 /* Enable bit for Inter module */ 20 #define TW5864_EMU_EN_ME BIT(1) 21 /* Enable bit for Sensor Interface module */ 22 #define TW5864_EMU_EN_SEN BIT(2) 23 /* Enable bit for Host Burst Access */ 24 #define TW5864_EMU_EN_BHOST BIT(3) 25 /* Enable bit for Loop Filter module */ 26 #define TW5864_EMU_EN_LPF BIT(4) 27 /* Enable bit for PLBK module */ 28 #define TW5864_EMU_EN_PLBK BIT(5) 29 /* 30 * Video Frame mapping in DDR 31 * 00 CIF 32 * 01 D1 33 * 10 Reserved 34 * 11 Reserved 35 * 36 */ 37 #define TW5864_DSP_FRAME_TYPE (3 << 6) 38 #define TW5864_DSP_FRAME_TYPE_D1 BIT(6) 39 40 #define TW5864_UNDECLARED_H264REV_PART2 0x0008 41 42 #define TW5864_SLICE 0x000c 43 /* Define controls in register TW5864_SLICE */ 44 /* VLC Slice end flag */ 45 #define TW5864_VLC_SLICE_END BIT(0) 46 /* Master Slice End Flag */ 47 #define TW5864_MAS_SLICE_END BIT(4) 48 /* Host to start a new slice Address */ 49 #define TW5864_START_NSLICE BIT(15) 50 51 /* 52 * [15:0] Two bit for each channel (channel 0 ~ 7). Each two bits are the buffer 53 * pointer for the last encoded frame of the corresponding channel. 54 */ 55 #define TW5864_ENC_BUF_PTR_REC1 0x0010 56 57 /* [5:0] DSP_MB_QP and [15:10] DSP_LPF_OFFSET */ 58 #define TW5864_DSP_QP 0x0018 59 /* Define controls in register TW5864_DSP_QP */ 60 /* [5:0] H264 QP Value for codec */ 61 #define TW5864_DSP_MB_QP 0x003f 62 /* 63 * [15:10] H264 LPF_OFFSET Address 64 * (Default 0) 65 */ 66 #define TW5864_DSP_LPF_OFFSET 0xfc00 67 68 #define TW5864_DSP_CODEC 0x001c 69 /* Define controls in register TW5864_DSP_CODEC */ 70 /* 71 * 0: Encode (TW5864 Default) 72 * 1: Decode 73 */ 74 #define TW5864_DSP_CODEC_MODE BIT(0) 75 /* 76 * 0->3 4 VLC data buffer in DDR (1M each) 77 * 0->7 8 VLC data buffer in DDR (512k each) 78 */ 79 #define TW5864_VLC_BUF_ID (7 << 2) 80 /* 81 * 0 4CIF in 1 MB 82 * 1 1CIF in 1 MB 83 */ 84 #define TW5864_CIF_MAP_MD BIT(6) 85 /* 86 * 0 2 falf D1 in 1 MB 87 * 1 1 half D1 in 1 MB 88 */ 89 #define TW5864_HD1_MAP_MD BIT(7) 90 /* VLC Stream valid */ 91 #define TW5864_VLC_VLD BIT(8) 92 /* MV Vector Valid */ 93 #define TW5864_MV_VECT_VLD BIT(9) 94 /* MV Flag Valid */ 95 #define TW5864_MV_FLAG_VLD BIT(10) 96 97 #define TW5864_DSP_SEN 0x0020 98 /* Define controls in register TW5864_DSP_SEN */ 99 /* Org Buffer Base for Luma (default 0) */ 100 #define TW5864_DSP_SEN_PIC_LU 0x000f 101 /* Org Buffer Base for Chroma (default 4) */ 102 #define TW5864_DSP_SEN_PIC_CHM 0x00f0 103 /* Maximum Number of Buffers (default 4) */ 104 #define TW5864_DSP_SEN_PIC_MAX 0x0700 105 /* 106 * Original Frame D1 or HD1 switch 107 * (Default 0) 108 */ 109 #define TW5864_DSP_SEN_HFULL 0x1000 110 111 #define TW5864_DSP_REF_PIC 0x0024 112 /* Define controls in register TW5864_DSP_REF_PIC */ 113 /* Ref Buffer Base for Luma (default 0) */ 114 #define TW5864_DSP_REF_PIC_LU 0x000f 115 /* Ref Buffer Base for Chroma (default 4) */ 116 #define TW5864_DSP_REF_PIC_CHM 0x00f0 117 /* Maximum Number of Buffers (default 4) */ 118 #define TW5864_DSP_REF_PIC_MAX 0x0700 119 120 /* [15:0] SEN_EN_CH[n] SENIF original frame capture enable for each channel */ 121 #define TW5864_SEN_EN_CH 0x0028 122 123 #define TW5864_DSP 0x002c 124 /* Define controls in register TW5864_DSP */ 125 /* The ID for channel selected for encoding operation */ 126 #define TW5864_DSP_ENC_CHN 0x000f 127 /* See DSP_MB_DELAY below */ 128 #define TW5864_DSP_MB_WAIT 0x0010 129 /* 130 * DSP Chroma Switch 131 * 0 DDRB 132 * 1 DDRA 133 */ 134 #define TW5864_DSP_CHROM_SW 0x0020 135 /* VLC Flow Control: 1 for enable */ 136 #define TW5864_DSP_FLW_CNTL 0x0040 137 /* 138 * If DSP_MB_WAIT == 0, MB delay is DSP_MB_DELAY * 16 139 * If DSP_MB_DELAY == 1, MB delay is DSP_MB_DELAY * 128 140 */ 141 #define TW5864_DSP_MB_DELAY 0x0f00 142 143 #define TW5864_DDR 0x0030 144 /* Define controls in register TW5864_DDR */ 145 /* DDR Single Access Page Number */ 146 #define TW5864_DDR_PAGE_CNTL 0x00ff 147 /* DDR-DPR Burst Read Enable */ 148 #define TW5864_DDR_BRST_EN BIT(13) 149 /* 150 * DDR A/B Select as HOST access 151 * 0 Select DDRA 152 * 1 Select DDRB 153 */ 154 #define TW5864_DDR_AB_SEL BIT(14) 155 /* 156 * DDR Access Mode Select 157 * 0 Single R/W Access (Host <-> DDR) 158 * 1 Burst R/W Access (Host <-> DPR) 159 */ 160 #define TW5864_DDR_MODE BIT(15) 161 162 /* The original frame capture pointer. Two bits for each channel */ 163 /* SENIF_ORG_FRM_PTR [15:0] */ 164 #define TW5864_SENIF_ORG_FRM_PTR1 0x0038 165 /* SENIF_ORG_FRM_PTR [31:16] */ 166 #define TW5864_SENIF_ORG_FRM_PTR2 0x003c 167 168 #define TW5864_DSP_SEN_MODE 0x0040 169 /* Define controls in register TW5864_DSP_SEN_MODE */ 170 #define TW5864_DSP_SEN_MODE_CH0 0x000f 171 #define TW5864_DSP_SEN_MODE_CH1 0x00f0 172 173 /* 174 * [15:0]: ENC_BUF_PTR_REC[31:16] Two bit for each channel (channel 8 ~ 15). 175 * Each two bits are the buffer pointer for the last encoded frame of a channel 176 */ 177 #define TW5864_ENC_BUF_PTR_REC2 0x004c 178 179 /* Current MV Flag Status Pointer for Channel n. (Read only) */ 180 /* 181 * [1:0] CH0_MV_PTR, ..., [15:14] CH7_MV_PTR 182 */ 183 #define TW5864_CH_MV_PTR1 0x0060 184 /* 185 * [1:0] CH8_MV_PTR, ..., [15:14] CH15_MV_PTR 186 */ 187 #define TW5864_CH_MV_PTR2 0x0064 188 189 /* 190 * [15:0] Reset Current MV Flag Status Pointer for Channel n (one bit each) 191 */ 192 #define TW5864_RST_MV_PTR 0x0068 193 #define TW5864_INTERLACING 0x0200 194 /* Define controls in register TW5864_INTERLACING */ 195 /* 196 * Inter_Mode Start. 2-nd bit? A guess. Missing in datasheet. Without this bit 197 * set, the output video is interlaced (stripy). 198 */ 199 #define TW5864_DSP_INTER_ST BIT(1) 200 /* Deinterlacer Enable */ 201 #define TW5864_DI_EN BIT(2) 202 /* 203 * De-interlacer Mode 204 * 1 Shuffled frame 205 * 0 Normal Un-Shuffled Frame 206 */ 207 #define TW5864_DI_MD BIT(3) 208 /* 209 * Down scale original frame in X direction 210 * 11: Un-used 211 * 10: down-sample to 1/4 212 * 01: down-sample to 1/2 213 * 00: down-sample disabled 214 */ 215 #define TW5864_DSP_DWN_X (3 << 4) 216 /* 217 * Down scale original frame in Y direction 218 * 11: Un-used 219 * 10: down-sample to 1/4 220 * 01: down-sample to 1/2 221 * 00: down-sample disabled 222 */ 223 #define TW5864_DSP_DWN_Y (3 << 6) 224 /* 225 * 1 Dual Stream 226 * 0 Single Stream 227 */ 228 #define TW5864_DUAL_STR BIT(8) 229 230 #define TW5864_DSP_REF 0x0204 231 /* Define controls in register TW5864_DSP_REF */ 232 /* Number of reference frame (Default 1 for TW5864B) */ 233 #define TW5864_DSP_REF_FRM 0x000f 234 /* Window size */ 235 #define TW5864_DSP_WIN_SIZE 0x02f0 236 237 #define TW5864_DSP_SKIP 0x0208 238 /* Define controls in register TW5864_DSP_SKIP */ 239 /* 240 * Skip Offset Enable bit 241 * 0 DSP_SKIP_OFFSET value is not used (default 8) 242 * 1 DSP_SKIP_OFFSET value is used in HW 243 */ 244 #define TW5864_DSP_SKIP_OFEN 0x0080 245 /* Skip mode cost offset (default 8) */ 246 #define TW5864_DSP_SKIP_OFFSET 0x007f 247 248 #define TW5864_MOTION_SEARCH_ETC 0x020c 249 /* Define controls in register TW5864_MOTION_SEARCH_ETC */ 250 /* Enable quarter pel search mode */ 251 #define TW5864_QPEL_EN BIT(0) 252 /* Enable half pel search mode */ 253 #define TW5864_HPEL_EN BIT(1) 254 /* Enable motion search mode */ 255 #define TW5864_ME_EN BIT(2) 256 /* Enable Intra mode */ 257 #define TW5864_INTRA_EN BIT(3) 258 /* Enable Skip Mode */ 259 #define TW5864_SKIP_EN BIT(4) 260 /* Search Option (Default 2"b01) */ 261 #define TW5864_SRCH_OPT (3 << 5) 262 263 #define TW5864_DSP_ENC_REC 0x0210 264 /* Define controls in register TW5864_DSP_ENC_REC */ 265 /* Reference Buffer Pointer for encoding */ 266 #define TW5864_DSP_ENC_REF_PTR 0x0007 267 /* Reconstruct Buffer pointer */ 268 #define TW5864_DSP_REC_BUF_PTR 0x7000 269 270 /* [15:0] Lambda Value for H264 */ 271 #define TW5864_DSP_REF_MVP_LAMBDA 0x0214 272 273 #define TW5864_DSP_PIC_MAX_MB 0x0218 274 /* Define controls in register TW5864_DSP_PIC_MAX_MB */ 275 /* The MB number in Y direction for a frame */ 276 #define TW5864_DSP_PIC_MAX_MB_Y 0x007f 277 /* The MB number in X direction for a frame */ 278 #define TW5864_DSP_PIC_MAX_MB_X 0x7f00 279 280 /* The original frame pointer for encoding */ 281 #define TW5864_DSP_ENC_ORG_PTR_REG 0x021c 282 /* Mask to use with TW5864_DSP_ENC_ORG_PTR */ 283 #define TW5864_DSP_ENC_ORG_PTR_MASK 0x7000 284 /* Number of bits to shift with TW5864_DSP_ENC_ORG_PTR */ 285 #define TW5864_DSP_ENC_ORG_PTR_SHIFT 12 286 287 /* DDR base address of OSD rectangle attribute data */ 288 #define TW5864_DSP_OSD_ATTRI_BASE 0x0220 289 /* OSD enable bit for each channel */ 290 #define TW5864_DSP_OSD_ENABLE 0x0228 291 292 /* 0x0280 ~ 0x029c – Motion Vector for 1st 4x4 Block, e.g., 80 (X), 84 (Y) */ 293 #define TW5864_ME_MV_VEC1 0x0280 294 /* 0x02a0 ~ 0x02bc – Motion Vector for 2nd 4x4 Block, e.g., A0 (X), A4 (Y) */ 295 #define TW5864_ME_MV_VEC2 0x02a0 296 /* 0x02c0 ~ 0x02dc – Motion Vector for 3rd 4x4 Block, e.g., C0 (X), C4 (Y) */ 297 #define TW5864_ME_MV_VEC3 0x02c0 298 /* 0x02e0 ~ 0x02fc – Motion Vector for 4th 4x4 Block, e.g., E0 (X), E4 (Y) */ 299 #define TW5864_ME_MV_VEC4 0x02e0 300 301 /* 302 * [5:0] 303 * if (intra16x16_cost < (intra4x4_cost+dsp_i4x4_offset)) 304 * Intra_mode = intra16x16_mode 305 * Else 306 * Intra_mode = intra4x4_mode 307 */ 308 #define TW5864_DSP_I4x4_OFFSET 0x040c 309 310 /* 311 * [6:4] 312 * 0x5 Only 4x4 313 * 0x6 Only 16x16 314 * 0x7 16x16 & 4x4 315 */ 316 #define TW5864_DSP_INTRA_MODE 0x0410 317 #define TW5864_DSP_INTRA_MODE_SHIFT 4 318 #define TW5864_DSP_INTRA_MODE_MASK (7 << 4) 319 #define TW5864_DSP_INTRA_MODE_4x4 0x5 320 #define TW5864_DSP_INTRA_MODE_16x16 0x6 321 #define TW5864_DSP_INTRA_MODE_4x4_AND_16x16 0x7 322 /* 323 * [5:0] WEIGHT Factor for I4x4 cost calculation (QP dependent) 324 */ 325 #define TW5864_DSP_I4x4_WEIGHT 0x0414 326 327 /* 328 * [7:0] Offset used to affect Intra/ME model decision 329 * If (me_cost < intra_cost + dsp_resid_mode_offset) 330 * Pred_Mode = me_mode 331 * Else 332 * Pred_mode = intra_mode 333 */ 334 #define TW5864_DSP_RESID_MODE_OFFSET 0x0604 335 336 /* 0x0800 ~ 0x09ff - Quantization TABLE Values */ 337 #define TW5864_QUAN_TAB 0x0800 338 339 /* Valid channel value [0; f], frame value [0; 3] */ 340 #define TW5864_RT_CNTR_CH_FRM(channel, frame) \ 341 (0x0c00 | (channel << 4) | (frame << 2)) 342 343 #define TW5864_FRAME_BUS1 0x0d00 344 /* 345 * 1 Progressive in part A in bus n 346 * 0 Interlaced in part A in bus n 347 */ 348 #define TW5864_PROG_A BIT(0) 349 /* 350 * 1 Progressive in part B in bus n 351 * 0 Interlaced in part B in bus n 352 */ 353 #define TW5864_PROG_B BIT(1) 354 /* 355 * 1 Frame Mode in bus n 356 * 0 Field Mode in bus n 357 */ 358 #define TW5864_FRAME BIT(2) 359 /* 360 * 0 4CIF in bus n 361 * 1 1D1 + 4 CIF in bus n 362 * 2 2D1 in bus n 363 */ 364 #define TW5864_BUS_D1 (3 << 3) 365 /* Bus 1 goes in TW5864_FRAME_BUS1 in [4:0] */ 366 /* Bus 2 goes in TW5864_FRAME_BUS1 in [12:8] */ 367 #define TW5864_FRAME_BUS2 0x0d04 368 /* Bus 3 goes in TW5864_FRAME_BUS2 in [4:0] */ 369 /* Bus 4 goes in TW5864_FRAME_BUS2 in [12:8] */ 370 371 /* [15:0] Horizontal Mirror for channel n */ 372 #define TW5864_SENIF_HOR_MIR 0x0d08 373 /* [15:0] Vertical Mirror for channel n */ 374 #define TW5864_SENIF_VER_MIR 0x0d0c 375 376 /* 377 * FRAME_WIDTH_BUSn_A 378 * 0x15f: 4 CIF 379 * 0x2cf: 1 D1 + 3 CIF 380 * 0x2cf: 2 D1 381 * FRAME_WIDTH_BUSn_B 382 * 0x15f: 4 CIF 383 * 0x2cf: 1 D1 + 3 CIF 384 * 0x2cf: 2 D1 385 * FRAME_HEIGHT_BUSn_A 386 * 0x11f: 4CIF (PAL) 387 * 0x23f: 1D1 + 3CIF (PAL) 388 * 0x23f: 2 D1 (PAL) 389 * 0x0ef: 4CIF (NTSC) 390 * 0x1df: 1D1 + 3CIF (NTSC) 391 * 0x1df: 2 D1 (NTSC) 392 * FRAME_HEIGHT_BUSn_B 393 * 0x11f: 4CIF (PAL) 394 * 0x23f: 1D1 + 3CIF (PAL) 395 * 0x23f: 2 D1 (PAL) 396 * 0x0ef: 4CIF (NTSC) 397 * 0x1df: 1D1 + 3CIF (NTSC) 398 * 0x1df: 2 D1 (NTSC) 399 */ 400 #define TW5864_FRAME_WIDTH_BUS_A(bus) (0x0d10 + 0x0010 * bus) 401 #define TW5864_FRAME_WIDTH_BUS_B(bus) (0x0d14 + 0x0010 * bus) 402 #define TW5864_FRAME_HEIGHT_BUS_A(bus) (0x0d18 + 0x0010 * bus) 403 #define TW5864_FRAME_HEIGHT_BUS_B(bus) (0x0d1c + 0x0010 * bus) 404 405 /* 406 * 1: the bus mapped Channel n Full D1 407 * 0: the bus mapped Channel n Half D1 408 */ 409 #define TW5864_FULL_HALF_FLAG 0x0d50 410 411 /* 412 * 0 The bus mapped Channel select partA Mode 413 * 1 The bus mapped Channel select partB Mode 414 */ 415 #define TW5864_FULL_HALF_MODE_SEL 0x0d54 416 417 #define TW5864_VLC 0x1000 418 /* Define controls in register TW5864_VLC */ 419 /* QP Value used by H264 CAVLC */ 420 #define TW5864_VLC_SLICE_QP 0x003f 421 /* 422 * Swap byte order of VLC stream in d-word. 423 * 1 Normal (VLC output= [31:0]) 424 * 0 Swap (VLC output={[23:16],[31:24],[7:0], [15:8]}) 425 */ 426 #define TW5864_VLC_BYTE_SWP BIT(6) 427 /* Enable Adding 03 circuit for VLC stream */ 428 #define TW5864_VLC_ADD03_EN BIT(7) 429 /* Number of bit for VLC bit Align */ 430 #define TW5864_VLC_BIT_ALIGN_SHIFT 8 431 #define TW5864_VLC_BIT_ALIGN_MASK (0x1f << 8) 432 /* 433 * Synchronous Interface select for VLC Stream 434 * 1 CDC_VLCS_MAS read VLC stream 435 * 0 CPU read VLC stream 436 */ 437 #define TW5864_VLC_INF_SEL BIT(13) 438 /* Enable VLC overflow control */ 439 #define TW5864_VLC_OVFL_CNTL BIT(14) 440 /* 441 * 1 PCI Master Mode 442 * 0 Non PCI Master Mode 443 */ 444 #define TW5864_VLC_PCI_SEL BIT(15) 445 /* 446 * 0 Enable Adding 03 to VLC header and stream 447 * 1 Disable Adding 03 to VLC header of "00000001" 448 */ 449 #define TW5864_VLC_A03_DISAB BIT(16) 450 /* 451 * Status of VLC stream in DDR (one bit for each buffer) 452 * 1 VLC is ready in buffer n (HW set) 453 * 0 VLC is not ready in buffer n (SW clear) 454 */ 455 #define TW5864_VLC_BUF_RDY_SHIFT 24 456 #define TW5864_VLC_BUF_RDY_MASK (0xff << 24) 457 458 /* Total number of bit in the slice */ 459 #define TW5864_SLICE_TOTAL_BIT 0x1004 460 /* Total number of bit in the residue */ 461 #define TW5864_RES_TOTAL_BIT 0x1008 462 463 #define TW5864_VLC_BUF 0x100c 464 /* Define controls in register TW5864_VLC_BUF */ 465 /* VLC BK0 full status, write ‘1’ to clear */ 466 #define TW5864_VLC_BK0_FULL BIT(0) 467 /* VLC BK1 full status, write ‘1’ to clear */ 468 #define TW5864_VLC_BK1_FULL BIT(1) 469 /* VLC end slice status, write ‘1’ to clear */ 470 #define TW5864_VLC_END_SLICE BIT(2) 471 /* VLC Buffer overflow status, write ‘1’ to clear */ 472 #define TW5864_DSP_RD_OF BIT(3) 473 /* VLC string length in either buffer 0 or 1 at end of frame */ 474 #define TW5864_VLC_STREAM_LEN_SHIFT 4 475 #define TW5864_VLC_STREAM_LEN_MASK (0x1ff << 4) 476 477 /* [15:0] Total coefficient number in a frame */ 478 #define TW5864_TOTAL_COEF_NO 0x1010 479 /* [0] VLC Encoder Interrupt. Write ‘1’ to clear */ 480 #define TW5864_VLC_DSP_INTR 0x1014 481 /* [31:0] VLC stream CRC checksum */ 482 #define TW5864_VLC_STREAM_CRC 0x1018 483 484 #define TW5864_VLC_RD 0x101c 485 /* Define controls in register TW5864_VLC_RD */ 486 /* 487 * 1 Read VLC lookup Memory 488 * 0 Read VLC Stream Memory 489 */ 490 #define TW5864_VLC_RD_MEM BIT(0) 491 /* 492 * 1 Read VLC Stream Memory in burst mode 493 * 0 Read VLC Stream Memory in single mode 494 */ 495 #define TW5864_VLC_RD_BRST BIT(1) 496 497 /* 0x2000 ~ 0x2ffc -- H264 Stream Memory Map */ 498 /* 499 * A word is 4 bytes. I.e., 500 * VLC_STREAM_MEM[0] address: 0x2000 501 * VLC_STREAM_MEM[1] address: 0x2004 502 * ... 503 * VLC_STREAM_MEM[3FF] address: 0x2ffc 504 */ 505 #define TW5864_VLC_STREAM_MEM_START 0x2000 506 #define TW5864_VLC_STREAM_MEM_MAX_OFFSET 0x3ff 507 #define TW5864_VLC_STREAM_MEM(offset) (TW5864_VLC_STREAM_MEM_START + 4 * offset) 508 509 /* 0x4000 ~ 0x4ffc -- Audio Register Map */ 510 /* [31:0] config 1ms cnt = Realtime clk/1000 */ 511 #define TW5864_CFG_1MS_CNT 0x4000 512 513 #define TW5864_ADPCM 0x4004 514 /* Define controls in register TW5864_ADPCM */ 515 /* ADPCM decoder enable */ 516 #define TW5864_ADPCM_DEC BIT(0) 517 /* ADPCM input data enable */ 518 #define TW5864_ADPCM_IN_DATA BIT(1) 519 /* ADPCM encoder enable */ 520 #define TW5864_ADPCM_ENC BIT(2) 521 522 #define TW5864_AUD 0x4008 523 /* Define controls in register TW5864_AUD */ 524 /* Record path PCM Audio enable bit for each channel */ 525 #define TW5864_AUD_ORG_CH_EN 0x00ff 526 /* Speaker path PCM Audio Enable */ 527 #define TW5864_SPK_ORG_EN BIT(16) 528 /* 529 * 0 16bit 530 * 1 8bit 531 */ 532 #define TW5864_AD_BIT_MODE BIT(17) 533 #define TW5864_AUD_TYPE_SHIFT 18 534 /* 535 * 0 PCM 536 * 3 ADPCM 537 */ 538 #define TW5864_AUD_TYPE (0xf << 18) 539 #define TW5864_AUD_SAMPLE_RATE_SHIFT 22 540 /* 541 * 0 8K 542 * 1 16K 543 */ 544 #define TW5864_AUD_SAMPLE_RATE (3 << 22) 545 /* Channel ID used to select audio channel (0 to 16) for loopback */ 546 #define TW5864_TESTLOOP_CHID_SHIFT 24 547 #define TW5864_TESTLOOP_CHID (0x1f << 24) 548 /* Enable AD Loopback Test */ 549 #define TW5864_TEST_ADLOOP_EN BIT(30) 550 /* 551 * 0 Asynchronous Mode or PCI target mode 552 * 1 PCI Initiator Mode 553 */ 554 #define TW5864_AUD_MODE BIT(31) 555 556 #define TW5864_AUD_ADPCM 0x400c 557 /* Define controls in register TW5864_AUD_ADPCM */ 558 /* Record path ADPCM audio channel enable, one bit for each */ 559 #define TW5864_AUD_ADPCM_CH_EN 0x00ff 560 /* Speaker path ADPCM audio channel enable */ 561 #define TW5864_SPK_ADPCM_EN BIT(16) 562 563 #define TW5864_PC_BLOCK_ADPCM_RD_NO 0x4018 564 #define TW5864_PC_BLOCK_ADPCM_RD_NO_MASK 0x1f 565 566 /* 567 * For ADPCM_ENC_WR_PTR, ADPCM_ENC_RD_PTR (see below): 568 * Bit[2:0] ch0 569 * Bit[5:3] ch1 570 * Bit[8:6] ch2 571 * Bit[11:9] ch3 572 * Bit[14:12] ch4 573 * Bit[17:15] ch5 574 * Bit[20:18] ch6 575 * Bit[23:21] ch7 576 * Bit[26:24] ch8 577 * Bit[29:27] ch9 578 * Bit[32:30] ch10 579 * Bit[35:33] ch11 580 * Bit[38:36] ch12 581 * Bit[41:39] ch13 582 * Bit[44:42] ch14 583 * Bit[47:45] ch15 584 * Bit[50:48] ch16 585 */ 586 #define TW5864_ADPCM_ENC_XX_MASK 0x3fff 587 #define TW5864_ADPCM_ENC_XX_PTR2_SHIFT 30 588 /* ADPCM_ENC_WR_PTR[29:0] */ 589 #define TW5864_ADPCM_ENC_WR_PTR1 0x401c 590 /* ADPCM_ENC_WR_PTR[50:30] */ 591 #define TW5864_ADPCM_ENC_WR_PTR2 0x4020 592 593 /* ADPCM_ENC_RD_PTR[29:0] */ 594 #define TW5864_ADPCM_ENC_RD_PTR1 0x4024 595 /* ADPCM_ENC_RD_PTR[50:30] */ 596 #define TW5864_ADPCM_ENC_RD_PTR2 0x4028 597 598 /* [3:0] rd ch0, [7:4] rd ch1, [11:8] wr ch0, [15:12] wr ch1 */ 599 #define TW5864_ADPCM_DEC_RD_WR_PTR 0x402c 600 601 /* 602 * For TW5864_AD_ORIG_WR_PTR, TW5864_AD_ORIG_RD_PTR: 603 * Bit[3:0] ch0 604 * Bit[7:4] ch1 605 * Bit[11:8] ch2 606 * Bit[15:12] ch3 607 * Bit[19:16] ch4 608 * Bit[23:20] ch5 609 * Bit[27:24] ch6 610 * Bit[31:28] ch7 611 * Bit[35:32] ch8 612 * Bit[39:36] ch9 613 * Bit[43:40] ch10 614 * Bit[47:44] ch11 615 * Bit[51:48] ch12 616 * Bit[55:52] ch13 617 * Bit[59:56] ch14 618 * Bit[63:60] ch15 619 * Bit[67:64] ch16 620 */ 621 /* AD_ORIG_WR_PTR[31:0] */ 622 #define TW5864_AD_ORIG_WR_PTR1 0x4030 623 /* AD_ORIG_WR_PTR[63:32] */ 624 #define TW5864_AD_ORIG_WR_PTR2 0x4034 625 /* AD_ORIG_WR_PTR[67:64] */ 626 #define TW5864_AD_ORIG_WR_PTR3 0x4038 627 628 /* AD_ORIG_RD_PTR[31:0] */ 629 #define TW5864_AD_ORIG_RD_PTR1 0x403c 630 /* AD_ORIG_RD_PTR[63:32] */ 631 #define TW5864_AD_ORIG_RD_PTR2 0x4040 632 /* AD_ORIG_RD_PTR[67:64] */ 633 #define TW5864_AD_ORIG_RD_PTR3 0x4044 634 635 #define TW5864_PC_BLOCK_ORIG_RD_NO 0x4048 636 #define TW5864_PC_BLOCK_ORIG_RD_NO_MASK 0x1f 637 638 #define TW5864_PCI_AUD 0x404c 639 /* Define controls in register TW5864_PCI_AUD */ 640 /* 641 * The register is applicable to PCI initiator mode only. Used to select PCM(0) 642 * or ADPCM(1) audio data sent to PC. One bit for each channel 643 */ 644 #define TW5864_PCI_DATA_SEL 0xffff 645 /* 646 * Audio flow control mode selection bit. 647 * 0 Flow control disabled. TW5864 continuously sends audio frame to PC 648 * (initiator mode) 649 * 1 Flow control enabled 650 */ 651 #define TW5864_PCI_FLOW_EN BIT(16) 652 /* 653 * When PCI_FLOW_EN is set, PCI need to toggle this bit to send an audio frame 654 * to PC. One toggle to send one frame. 655 */ 656 #define TW5864_PCI_AUD_FRM_EN BIT(17) 657 658 /* [1:0] CS valid to data valid CLK cycles when writing operation */ 659 #define TW5864_CS2DAT_CNT 0x8000 660 /* [2:0] Data valid signal width by system clock cycles */ 661 #define TW5864_DATA_VLD_WIDTH 0x8004 662 663 #define TW5864_SYNC 0x8008 664 /* Define controls in register TW5864_SYNC */ 665 /* 666 * 0 vlc stream to syncrous port 667 * 1 vlc stream to ddr buffers 668 */ 669 #define TW5864_SYNC_CFG BIT(7) 670 /* 671 * 0 SYNC Address sampled on Rising edge 672 * 1 SYNC Address sampled on Falling edge 673 */ 674 #define TW5864_SYNC_ADR_EDGE BIT(0) 675 #define TW5864_VLC_STR_DELAY_SHIFT 1 676 /* 677 * 0 No system delay 678 * 1 One system clock delay 679 * 2 Two system clock delay 680 * 3 Three system clock delay 681 */ 682 #define TW5864_VLC_STR_DELAY (3 << 1) 683 /* 684 * 0 Rising edge output 685 * 1 Falling edge output 686 */ 687 #define TW5864_VLC_OUT_EDGE BIT(3) 688 689 /* 690 * [1:0] 691 * 2’b00 phase set to 180 degree 692 * 2’b01 phase set to 270 degree 693 * 2’b10 phase set to 0 degree 694 * 2’b11 phase set to 90 degree 695 */ 696 #define TW5864_I2C_PHASE_CFG 0x800c 697 698 /* 699 * The system / DDR clock (166 MHz) is generated with an on-chip system clock 700 * PLL (SYSPLL) using input crystal clock of 27 MHz. The system clock PLL 701 * frequency is controlled with the following equation. 702 * CLK_OUT = CLK_IN * (M+1) / ((N+1) * P) 703 * SYSPLL_M M parameter 704 * SYSPLL_N N parameter 705 * SYSPLL_P P parameter 706 */ 707 /* SYSPLL_M[7:0] */ 708 #define TW5864_SYSPLL1 0x8018 709 /* Define controls in register TW5864_SYSPLL1 */ 710 #define TW5864_SYSPLL_M_LOW 0x00ff 711 712 /* [2:0]: SYSPLL_M[10:8], [7:3]: SYSPLL_N[4:0] */ 713 #define TW5864_SYSPLL2 0x8019 714 /* Define controls in register TW5864_SYSPLL2 */ 715 #define TW5864_SYSPLL_M_HI 0x07 716 #define TW5864_SYSPLL_N_LOW_SHIFT 3 717 #define TW5864_SYSPLL_N_LOW (0x1f << 3) 718 719 /* 720 * [1:0]: SYSPLL_N[6:5], [3:2]: SYSPLL_P, [4]: SYSPLL_IREF, [7:5]: SYSPLL_CP_SEL 721 */ 722 #define TW5864_SYSPLL3 0x8020 723 /* Define controls in register TW5864_SYSPLL3 */ 724 #define TW5864_SYSPLL_N_HI 0x03 725 #define TW5864_SYSPLL_P_SHIFT 2 726 #define TW5864_SYSPLL_P (0x03 << 2) 727 /* 728 * SYSPLL bias current control 729 * 0 Lower current (default) 730 * 1 30% higher current 731 */ 732 #define TW5864_SYSPLL_IREF BIT(4) 733 /* 734 * SYSPLL charge pump current selection 735 * 0 1,5 uA 736 * 1 4 uA 737 * 2 9 uA 738 * 3 19 uA 739 * 4 39 uA 740 * 5 79 uA 741 * 6 159 uA 742 * 7 319 uA 743 */ 744 #define TW5864_SYSPLL_CP_SEL_SHIFT 5 745 #define TW5864_SYSPLL_CP_SEL (0x07 << 5) 746 747 /* 748 * [1:0]: SYSPLL_VCO, [3:2]: SYSPLL_LP_X8, [5:4]: SYSPLL_ICP_SEL, 749 * [6]: SYSPLL_LPF_5PF, [7]: SYSPLL_ED_SEL 750 */ 751 #define TW5864_SYSPLL4 0x8021 752 /* Define controls in register TW5864_SYSPLL4 */ 753 /* 754 * SYSPLL_VCO VCO Range selection 755 * 00 5 ~ 75 MHz 756 * 01 50 ~ 140 MHz 757 * 10 110 ~ 320 MHz 758 * 11 270 ~ 700 MHz 759 */ 760 #define TW5864_SYSPLL_VCO 0x03 761 #define TW5864_SYSPLL_LP_X8_SHIFT 2 762 /* 763 * Loop resister 764 * 0 38.5K ohms 765 * 1 6.6K ohms (default) 766 * 2 2.2K ohms 767 * 3 1.1K ohms 768 */ 769 #define TW5864_SYSPLL_LP_X8 (0x03 << 2) 770 #define TW5864_SYSPLL_ICP_SEL_SHIFT 4 771 /* 772 * PLL charge pump fine tune 773 * 00 x1 (default) 774 * 01 x1/2 775 * 10 x1/7 776 * 11 x1/8 777 */ 778 #define TW5864_SYSPLL_ICP_SEL (0x03 << 4) 779 /* 780 * PLL low pass filter phase margin adjustment 781 * 0 no 5pF (default) 782 * 1 5pF added 783 */ 784 #define TW5864_SYSPLL_LPF_5PF BIT(6) 785 /* 786 * PFD select edge for detection 787 * 0 Falling edge (default) 788 * 1 Rising edge 789 */ 790 #define TW5864_SYSPLL_ED_SEL BIT(7) 791 792 /* [0]: SYSPLL_RST, [4]: SYSPLL_PD */ 793 #define TW5864_SYSPLL5 0x8024 794 /* Define controls in register TW5864_SYSPLL5 */ 795 /* Reset SYSPLL */ 796 #define TW5864_SYSPLL_RST BIT(0) 797 /* Power down SYSPLL */ 798 #define TW5864_SYSPLL_PD BIT(4) 799 800 #define TW5864_PLL_CFG 0x801c 801 /* Define controls in register TW5864_PLL_CFG */ 802 /* 803 * Issue Soft Reset from Async Host Interface / PCI Interface clock domain. 804 * Become valid after sync to the xtal clock domain. This bit is set only if 805 * LOAD register bit is also set to 1. 806 */ 807 #define TW5864_SRST BIT(0) 808 /* 809 * Issue SYSPLL (166 MHz) configuration latch from Async host interface / PCI 810 * Interface clock domain. The configuration setting becomes effective only if 811 * LOAD register bit is also set to 1. 812 */ 813 #define TW5864_SYSPLL_CFG BIT(2) 814 /* 815 * Issue SPLL (108 MHz) configuration load from Async host interface / PCI 816 * Interface clock domain. The configuration setting becomes effective only if 817 * the LOAD register bit is also set to 1. 818 */ 819 #define TW5864_SPLL_CFG BIT(4) 820 /* 821 * Set this bit to latch the SRST, SYSPLL_CFG, SPLL_CFG setting into the xtal 822 * clock domain to restart the PLL. This bit is self cleared. 823 */ 824 #define TW5864_LOAD BIT(3) 825 826 /* SPLL_IREF, SPLL_LPX4, SPLL_CPX4, SPLL_PD, SPLL_DBG */ 827 #define TW5864_SPLL 0x8028 828 829 /* 0x8800 ~ 0x88fc -- Interrupt Register Map */ 830 /* 831 * Trigger mode of interrupt source 0 ~ 15 832 * 1 Edge trigger mode 833 * 0 Level trigger mode 834 */ 835 #define TW5864_TRIGGER_MODE_L 0x8800 836 /* Trigger mode of interrupt source 16 ~ 31 */ 837 #define TW5864_TRIGGER_MODE_H 0x8804 838 /* Enable of interrupt source 0 ~ 15 */ 839 #define TW5864_INTR_ENABLE_L 0x8808 840 /* Enable of interrupt source 16 ~ 31 */ 841 #define TW5864_INTR_ENABLE_H 0x880c 842 /* Clear interrupt command of interrupt source 0 ~ 15 */ 843 #define TW5864_INTR_CLR_L 0x8810 844 /* Clear interrupt command of interrupt source 16 ~ 31 */ 845 #define TW5864_INTR_CLR_H 0x8814 846 /* 847 * Assertion of interrupt source 0 ~ 15 848 * 1 High level or pos-edge is assertion 849 * 0 Low level or neg-edge is assertion 850 */ 851 #define TW5864_INTR_ASSERT_L 0x8818 852 /* Assertion of interrupt source 16 ~ 31 */ 853 #define TW5864_INTR_ASSERT_H 0x881c 854 /* 855 * Output level of interrupt 856 * 1 Interrupt output is high assertion 857 * 0 Interrupt output is low assertion 858 */ 859 #define TW5864_INTR_OUT_LEVEL 0x8820 860 /* 861 * Status of interrupt source 0 ~ 15 862 * Bit[0]: VLC 4k RAM interrupt 863 * Bit[1]: BURST DDR RAM interrupt 864 * Bit[2]: MV DSP interrupt 865 * Bit[3]: video lost interrupt 866 * Bit[4]: gpio 0 interrupt 867 * Bit[5]: gpio 1 interrupt 868 * Bit[6]: gpio 2 interrupt 869 * Bit[7]: gpio 3 interrupt 870 * Bit[8]: gpio 4 interrupt 871 * Bit[9]: gpio 5 interrupt 872 * Bit[10]: gpio 6 interrupt 873 * Bit[11]: gpio 7 interrupt 874 * Bit[12]: JPEG interrupt 875 * Bit[13:15]: Reserved 876 */ 877 #define TW5864_INTR_STATUS_L 0x8838 878 /* 879 * Status of interrupt source 16 ~ 31 880 * Bit[0]: Reserved 881 * Bit[1]: VLC done interrupt 882 * Bit[2]: Reserved 883 * Bit[3]: AD Vsync interrupt 884 * Bit[4]: Preview eof interrupt 885 * Bit[5]: Preview overflow interrupt 886 * Bit[6]: Timer interrupt 887 * Bit[7]: Reserved 888 * Bit[8]: Audio eof interrupt 889 * Bit[9]: I2C done interrupt 890 * Bit[10]: AD interrupt 891 * Bit[11:15]: Reserved 892 */ 893 #define TW5864_INTR_STATUS_H 0x883c 894 895 /* Defines of interrupt bits, united for both low and high word registers */ 896 #define TW5864_INTR_VLC_RAM BIT(0) 897 #define TW5864_INTR_BURST BIT(1) 898 #define TW5864_INTR_MV_DSP BIT(2) 899 #define TW5864_INTR_VIN_LOST BIT(3) 900 /* n belongs to [0; 7] */ 901 #define TW5864_INTR_GPIO(n) (1 << (4 + n)) 902 #define TW5864_INTR_JPEG BIT(12) 903 #define TW5864_INTR_VLC_DONE BIT(17) 904 #define TW5864_INTR_AD_VSYNC BIT(19) 905 #define TW5864_INTR_PV_EOF BIT(20) 906 #define TW5864_INTR_PV_OVERFLOW BIT(21) 907 #define TW5864_INTR_TIMER BIT(22) 908 #define TW5864_INTR_AUD_EOF BIT(24) 909 #define TW5864_INTR_I2C_DONE BIT(25) 910 #define TW5864_INTR_AD BIT(26) 911 912 /* 0x9000 ~ 0x920c -- Video Capture (VIF) Register Map */ 913 /* 914 * H264EN_CH_STATUS[n] Status of Vsync synchronized H264EN_CH_EN (Read Only) 915 * 1 Channel Enabled 916 * 0 Channel Disabled 917 */ 918 #define TW5864_H264EN_CH_STATUS 0x9000 919 /* 920 * [15:0] H264EN_CH_EN[n] H264 Encoding Path Enable for channel 921 * 1 Channel Enabled 922 * 0 Channel Disabled 923 */ 924 #define TW5864_H264EN_CH_EN 0x9004 925 /* 926 * H264EN_CH_DNS[n] H264 Encoding Path Downscale Video Decoder Input for 927 * channel n 928 * 1 Downscale Y to 1/2 929 * 0 Does not downscale 930 */ 931 #define TW5864_H264EN_CH_DNS 0x9008 932 /* 933 * H264EN_CH_PROG[n] H264 Encoding Path channel n is progressive 934 * 1 Progressive (Not valid for TW5864) 935 * 0 Interlaced (TW5864 default) 936 */ 937 #define TW5864_H264EN_CH_PROG 0x900c 938 /* 939 * [3:0] H264EN_BUS_MAX_CH[n] 940 * H264 Encoding Path maximum number of channel on BUS n 941 * 0 Max 4 channels 942 * 1 Max 2 channels 943 */ 944 #define TW5864_H264EN_BUS_MAX_CH 0x9010 945 946 /* 947 * H264EN_RATE_MAX_LINE_n H264 Encoding path Rate Mapping Maximum Line Number 948 * on Bus n 949 */ 950 #define TW5864_H264EN_RATE_MAX_LINE_EVEN 0x1f 951 #define TW5864_H264EN_RATE_MAX_LINE_ODD_SHIFT 5 952 #define TW5864_H264EN_RATE_MAX_LINE_ODD (0x1f << 5) 953 /* 954 * [4:0] H264EN_RATE_MAX_LINE_0 955 * [9:5] H264EN_RATE_MAX_LINE_1 956 */ 957 #define TW5864_H264EN_RATE_MAX_LINE_REG1 0x9014 958 /* 959 * [4:0] H264EN_RATE_MAX_LINE_2 960 * [9:5] H264EN_RATE_MAX_LINE_3 961 */ 962 #define TW5864_H264EN_RATE_MAX_LINE_REG2 0x9018 963 964 /* 965 * H264EN_CHn_FMT H264 Encoding Path Format configuration of Channel n 966 * 00 D1 (For D1 and hD1 frame) 967 * 01 (Reserved) 968 * 10 (Reserved) 969 * 11 D1 with 1/2 size in X (for CIF frame) 970 * Note: To be used with 0x9008 register to configure the frame size 971 */ 972 /* 973 * [1:0]: H264EN_CH0_FMT, 974 * ..., [15:14]: H264EN_CH7_FMT 975 */ 976 #define TW5864_H264EN_CH_FMT_REG1 0x9020 977 /* 978 * [1:0]: H264EN_CH8_FMT (?), 979 * ..., [15:14]: H264EN_CH15_FMT (?) 980 */ 981 #define TW5864_H264EN_CH_FMT_REG2 0x9024 982 983 /* 984 * H264EN_RATE_CNTL_BUSm_CHn H264 Encoding Path BUS m Rate Control for Channel n 985 */ 986 #define TW5864_H264EN_RATE_CNTL_LO_WORD(bus, channel) \ 987 (0x9100 + bus * 0x20 + channel * 0x08) 988 #define TW5864_H264EN_RATE_CNTL_HI_WORD(bus, channel) \ 989 (0x9104 + bus * 0x20 + channel * 0x08) 990 991 /* 992 * H264EN_BUSm_MAP_CHn The 16-to-1 MUX configuration register for each encoding 993 * channel (total of 16 channels). Four bits for each channel. 994 */ 995 #define TW5864_H264EN_BUS0_MAP 0x9200 996 #define TW5864_H264EN_BUS1_MAP 0x9204 997 #define TW5864_H264EN_BUS2_MAP 0x9208 998 #define TW5864_H264EN_BUS3_MAP 0x920c 999 1000 /* This register is not defined in datasheet, but used in reference driver */ 1001 #define TW5864_UNDECLARED_ERROR_FLAGS_0x9218 0x9218 1002 1003 #define TW5864_GPIO1 0x9800 1004 #define TW5864_GPIO2 0x9804 1005 /* Define controls in registers TW5864_GPIO1, TW5864_GPIO2 */ 1006 /* GPIO DATA of Group n */ 1007 #define TW5864_GPIO_DATA 0x00ff 1008 #define TW5864_GPIO_OEN_SHIFT 8 1009 /* GPIO Output Enable of Group n */ 1010 #define TW5864_GPIO_OEN (0xff << 8) 1011 1012 /* 0xa000 ~ 0xa8ff – DDR Controller Register Map */ 1013 /* DDR Controller A */ 1014 /* 1015 * [2:0] Data valid counter after read command to DDR. This is the delay value 1016 * to show how many cycles the data will be back from DDR after we issue a read 1017 * command. 1018 */ 1019 #define TW5864_RD_ACK_VLD_MUX 0xa000 1020 1021 #define TW5864_DDR_PERIODS 0xa004 1022 /* Define controls in register TW5864_DDR_PERIODS */ 1023 /* 1024 * Tras value, the minimum cycle of active to precharge command period, 1025 * default is 7 1026 */ 1027 #define TW5864_TRAS_CNT_MAX 0x000f 1028 /* 1029 * Trfc value, the minimum cycle of refresh to active or refresh command period, 1030 * default is 4"hf 1031 */ 1032 #define TW5864_RFC_CNT_MAX_SHIFT 8 1033 #define TW5864_RFC_CNT_MAX (0x0f << 8) 1034 /* 1035 * Trcd value, the minimum cycle of active to internal read/write command 1036 * period, default is 4"h2 1037 */ 1038 #define TW5864_TCD_CNT_MAX_SHIFT 4 1039 #define TW5864_TCD_CNT_MAX (0x0f << 4) 1040 /* Twr value, write recovery time, default is 4"h3 */ 1041 #define TW5864_TWR_CNT_MAX_SHIFT 12 1042 #define TW5864_TWR_CNT_MAX (0x0f << 12) 1043 1044 /* 1045 * [2:0] CAS latency, the delay cycle between internal read command and the 1046 * availability of the first bit of output data, default is 3 1047 */ 1048 #define TW5864_CAS_LATENCY 0xa008 1049 /* 1050 * [15:0] Maximum average periodic refresh, the value is based on the current 1051 * frequency to match 7.8mcs 1052 */ 1053 #define TW5864_DDR_REF_CNTR_MAX 0xa00c 1054 /* 1055 * DDR_ON_CHIP_MAP [1:0] 1056 * 0 256M DDR on board 1057 * 1 512M DDR on board 1058 * 2 1G DDR on board 1059 * DDR_ON_CHIP_MAP [2] 1060 * 0 Only one DDR chip 1061 * 1 Two DDR chips 1062 */ 1063 #define TW5864_DDR_ON_CHIP_MAP 0xa01c 1064 #define TW5864_DDR_SELFTEST_MODE 0xa020 1065 /* Define controls in register TW5864_DDR_SELFTEST_MODE */ 1066 /* 1067 * 0 Common read/write mode 1068 * 1 DDR self-test mode 1069 */ 1070 #define TW5864_MASTER_MODE BIT(0) 1071 /* 1072 * 0 DDR self-test single read/write 1073 * 1 DDR self-test burst read/write 1074 */ 1075 #define TW5864_SINGLE_PROC BIT(1) 1076 /* 1077 * 0 DDR self-test write command 1078 * 1 DDR self-test read command 1079 */ 1080 #define TW5864_WRITE_FLAG BIT(2) 1081 #define TW5864_DATA_MODE_SHIFT 4 1082 /* 1083 * 0 write 32'haaaa5555 to DDR 1084 * 1 write 32'hffffffff to DDR 1085 * 2 write 32'hha5a55a5a to DDR 1086 * 3 write increasing data to DDR 1087 */ 1088 #define TW5864_DATA_MODE (0x3 << 4) 1089 1090 /* [7:0] The maximum data of one burst in DDR self-test mode */ 1091 #define TW5864_BURST_CNTR_MAX 0xa024 1092 /* [15:0] The maximum burst counter (bit 15~0) in DDR self-test mode */ 1093 #define TW5864_DDR_PROC_CNTR_MAX_L 0xa028 1094 /* The maximum burst counter (bit 31~16) in DDR self-test mode */ 1095 #define TW5864_DDR_PROC_CNTR_MAX_H 0xa02c 1096 /* [0]: Start one DDR self-test */ 1097 #define TW5864_DDR_SELF_TEST_CMD 0xa030 1098 /* The maximum error counter (bit 15 ~ 0) in DDR self-test */ 1099 #define TW5864_ERR_CNTR_L 0xa034 1100 1101 #define TW5864_ERR_CNTR_H_AND_FLAG 0xa038 1102 /* Define controls in register TW5864_ERR_CNTR_H_AND_FLAG */ 1103 /* The maximum error counter (bit 30 ~ 16) in DDR self-test */ 1104 #define TW5864_ERR_CNTR_H_MASK 0x3fff 1105 /* DDR self-test end flag */ 1106 #define TW5864_END_FLAG 0x8000 1107 1108 /* 1109 * DDR Controller B: same as 0xa000 ~ 0xa038, but add TW5864_DDR_B_OFFSET to all 1110 * addresses 1111 */ 1112 #define TW5864_DDR_B_OFFSET 0x0800 1113 1114 /* 0xb004 ~ 0xb018 – HW version/ARB12 Register Map */ 1115 /* [15:0] Default is C013 */ 1116 #define TW5864_HW_VERSION 0xb004 1117 1118 #define TW5864_REQS_ENABLE 0xb010 1119 /* Define controls in register TW5864_REQS_ENABLE */ 1120 /* Audio data in to DDR enable (default 1) */ 1121 #define TW5864_AUD_DATA_IN_ENB BIT(0) 1122 /* Audio encode request to DDR enable (default 1) */ 1123 #define TW5864_AUD_ENC_REQ_ENB BIT(1) 1124 /* Audio decode request0 to DDR enable (default 1) */ 1125 #define TW5864_AUD_DEC_REQ0_ENB BIT(2) 1126 /* Audio decode request1 to DDR enable (default 1) */ 1127 #define TW5864_AUD_DEC_REQ1_ENB BIT(3) 1128 /* VLC stream request to DDR enable (default 1) */ 1129 #define TW5864_VLC_STRM_REQ_ENB BIT(4) 1130 /* H264 MV request to DDR enable (default 1) */ 1131 #define TW5864_DVM_MV_REQ_ENB BIT(5) 1132 /* mux_core MVD request to DDR enable (default 1) */ 1133 #define TW5864_MVD_REQ_ENB BIT(6) 1134 /* mux_core MVD temp data request to DDR enable (default 1) */ 1135 #define TW5864_MVD_TMP_REQ_ENB BIT(7) 1136 /* JPEG request to DDR enable (default 1) */ 1137 #define TW5864_JPEG_REQ_ENB BIT(8) 1138 /* mv_flag request to DDR enable (default 1) */ 1139 #define TW5864_MV_FLAG_REQ_ENB BIT(9) 1140 1141 #define TW5864_ARB12 0xb018 1142 /* Define controls in register TW5864_ARB12 */ 1143 /* ARB12 Enable (default 1) */ 1144 #define TW5864_ARB12_ENB BIT(15) 1145 /* ARB12 maximum value of time out counter (default 15"h1FF) */ 1146 #define TW5864_ARB12_TIME_OUT_CNT 0x7fff 1147 1148 /* 0xb800 ~ 0xb80c -- Indirect Access Register Map */ 1149 /* 1150 * Spec says: 1151 * In order to access the indirect register space, the following procedure is 1152 * followed. 1153 * But reference driver implementation, and current driver, too, does it 1154 * differently. 1155 * 1156 * Write Registers: 1157 * (1) Write IND_DATA at 0xb804 ~ 0xb807 1158 * (2) Read BUSY flag from 0xb803. Wait until BUSY signal is 0. 1159 * (3) Write IND_ADDR at 0xb800 ~ 0xb801. Set R/W to "1", ENABLE to "1" 1160 * Read Registers: 1161 * (1) Read BUSY flag from 0xb803. Wait until BUSY signal is 0. 1162 * (2) Write IND_ADDR at 0xb800 ~ 0xb801. Set R/W to "0", ENABLE to "1" 1163 * (3) Read BUSY flag from 0xb803. Wait until BUSY signal is 0. 1164 * (4) Read IND_DATA from 0xb804 ~ 0xb807 1165 */ 1166 #define TW5864_IND_CTL 0xb800 1167 /* Define controls in register TW5864_IND_CTL */ 1168 /* Address used to access indirect register space */ 1169 #define TW5864_IND_ADDR 0x0000ffff 1170 /* Wait until this bit is "0" before using indirect access */ 1171 #define TW5864_BUSY BIT(31) 1172 /* Activate the indirect access. This bit is self cleared */ 1173 #define TW5864_ENABLE BIT(25) 1174 /* Read/Write command */ 1175 #define TW5864_RW BIT(24) 1176 1177 /* [31:0] Data used to read/write indirect register space */ 1178 #define TW5864_IND_DATA 0xb804 1179 1180 /* 0xc000 ~ 0xc7fc -- Preview Register Map */ 1181 /* Mostly skipped this section. */ 1182 /* 1183 * [15:0] Status of Vsync Synchronized PCI_PV_CH_EN (Read Only) 1184 * 1 Channel Enabled 1185 * 0 Channel Disabled 1186 */ 1187 #define TW5864_PCI_PV_CH_STATUS 0xc000 1188 /* 1189 * [15:0] PCI Preview Path Enable for channel n 1190 * 1 Channel Enable 1191 * 0 Channel Disable 1192 */ 1193 #define TW5864_PCI_PV_CH_EN 0xc004 1194 1195 /* 0xc800 ~ 0xc804 -- JPEG Capture Register Map */ 1196 /* Skipped. */ 1197 /* 0xd000 ~ 0xd0fc -- JPEG Control Register Map */ 1198 /* Skipped. */ 1199 1200 /* 0xe000 ~ 0xfc04 – Motion Vector Register Map */ 1201 1202 /* ME Motion Vector data (Four Byte Each) 0xe000 ~ 0xe7fc */ 1203 #define TW5864_ME_MV_VEC_START 0xe000 1204 #define TW5864_ME_MV_VEC_MAX_OFFSET 0x1ff 1205 #define TW5864_ME_MV_VEC(offset) (TW5864_ME_MV_VEC_START + 4 * offset) 1206 1207 #define TW5864_MV 0xfc00 1208 /* Define controls in register TW5864_MV */ 1209 /* mv bank0 full status , write "1" to clear */ 1210 #define TW5864_MV_BK0_FULL BIT(0) 1211 /* mv bank1 full status , write "1" to clear */ 1212 #define TW5864_MV_BK1_FULL BIT(1) 1213 /* slice end status; write "1" to clear */ 1214 #define TW5864_MV_EOF BIT(2) 1215 /* mv encode interrupt status; write "1" to clear */ 1216 #define TW5864_MV_DSP_INTR BIT(3) 1217 /* mv write memory overflow, write "1" to clear */ 1218 #define TW5864_DSP_WR_OF BIT(4) 1219 #define TW5864_MV_LEN_SHIFT 5 1220 /* mv stream length */ 1221 #define TW5864_MV_LEN (0xff << 5) 1222 /* The configured status bit written into bit 15 of 0xfc04 */ 1223 #define TW5864_MPI_DDR_SEL BIT(13) 1224 1225 #define TW5864_MPI_DDR_SEL_REG 0xfc04 1226 /* Define controls in register TW5864_MPI_DDR_SEL_REG */ 1227 /* 1228 * SW configure register 1229 * 0 MV is saved in internal DPR 1230 * 1 MV is saved in DDR 1231 */ 1232 #define TW5864_MPI_DDR_SEL2 BIT(15) 1233 1234 /* 0x18000 ~ 0x181fc – PCI Master/Slave Control Map */ 1235 #define TW5864_PCI_INTR_STATUS 0x18000 1236 /* Define controls in register TW5864_PCI_INTR_STATUS */ 1237 /* vlc done */ 1238 #define TW5864_VLC_DONE_INTR BIT(1) 1239 /* ad vsync */ 1240 #define TW5864_AD_VSYNC_INTR BIT(3) 1241 /* preview eof */ 1242 #define TW5864_PREV_EOF_INTR BIT(4) 1243 /* preview overflow interrupt */ 1244 #define TW5864_PREV_OVERFLOW_INTR BIT(5) 1245 /* timer interrupt */ 1246 #define TW5864_TIMER_INTR BIT(6) 1247 /* audio eof */ 1248 #define TW5864_AUDIO_EOF_INTR BIT(8) 1249 /* IIC done */ 1250 #define TW5864_IIC_DONE_INTR BIT(24) 1251 /* ad interrupt (e.g.: video lost, video format changed) */ 1252 #define TW5864_AD_INTR_REG BIT(25) 1253 1254 #define TW5864_PCI_INTR_CTL 0x18004 1255 /* Define controls in register TW5864_PCI_INTR_CTL */ 1256 /* master enable */ 1257 #define TW5864_PCI_MAST_ENB BIT(0) 1258 /* mvd&vlc master enable */ 1259 #define TW5864_MVD_VLC_MAST_ENB 0x06 1260 /* (Need to set 0 in TW5864A) */ 1261 #define TW5864_AD_MAST_ENB BIT(3) 1262 /* preview master enable */ 1263 #define TW5864_PREV_MAST_ENB BIT(4) 1264 /* preview overflow enable */ 1265 #define TW5864_PREV_OVERFLOW_ENB BIT(5) 1266 /* timer interrupt enable */ 1267 #define TW5864_TIMER_INTR_ENB BIT(6) 1268 /* JPEG master (push mode) enable */ 1269 #define TW5864_JPEG_MAST_ENB BIT(7) 1270 #define TW5864_AU_MAST_ENB_CHN_SHIFT 8 1271 /* audio master channel enable */ 1272 #define TW5864_AU_MAST_ENB_CHN (0xffff << 8) 1273 /* IIC interrupt enable */ 1274 #define TW5864_IIC_INTR_ENB BIT(24) 1275 /* ad interrupt enable */ 1276 #define TW5864_AD_INTR_ENB BIT(25) 1277 /* target burst enable */ 1278 #define TW5864_PCI_TAR_BURST_ENB BIT(26) 1279 /* vlc stream burst enable */ 1280 #define TW5864_PCI_VLC_BURST_ENB BIT(27) 1281 /* ddr burst enable (1 enable, and must set DDR_BRST_EN) */ 1282 #define TW5864_PCI_DDR_BURST_ENB BIT(28) 1283 1284 /* 1285 * Because preview and audio have 16 channels separately, so using this 1286 * registers to indicate interrupt status for every channels. This is secondary 1287 * interrupt status register. OR operating of the PREV_INTR_REG is 1288 * PREV_EOF_INTR, OR operating of the AU_INTR_REG bits is AUDIO_EOF_INTR 1289 */ 1290 #define TW5864_PREV_AND_AU_INTR 0x18008 1291 /* Define controls in register TW5864_PREV_AND_AU_INTR */ 1292 /* preview eof interrupt flag */ 1293 #define TW5864_PREV_INTR_REG 0x0000ffff 1294 #define TW5864_AU_INTR_REG_SHIFT 16 1295 /* audio eof interrupt flag */ 1296 #define TW5864_AU_INTR_REG (0xffff << 16) 1297 1298 #define TW5864_MASTER_ENB_REG 0x1800c 1299 /* Define controls in register TW5864_MASTER_ENB_REG */ 1300 /* master enable */ 1301 #define TW5864_PCI_VLC_INTR_ENB BIT(1) 1302 /* mvd and vlc master enable */ 1303 #define TW5864_PCI_PREV_INTR_ENB BIT(4) 1304 /* ad vsync master enable */ 1305 #define TW5864_PCI_PREV_OF_INTR_ENB BIT(5) 1306 /* jpeg master enable */ 1307 #define TW5864_PCI_JPEG_INTR_ENB BIT(7) 1308 /* preview master enable */ 1309 #define TW5864_PCI_AUD_INTR_ENB BIT(8) 1310 1311 /* 1312 * Every channel of preview and audio have ping-pong buffers in system memory, 1313 * this register is the buffer flag to notify software which buffer is been 1314 * operated. 1315 */ 1316 #define TW5864_PREV_AND_AU_BUF_FLAG 0x18010 1317 /* Define controls in register TW5864_PREV_AND_AU_BUF_FLAG */ 1318 /* preview buffer A/B flag */ 1319 #define TW5864_PREV_BUF_FLAG 0xffff 1320 #define TW5864_AUDIO_BUF_FLAG_SHIFT 16 1321 /* audio buffer A/B flag */ 1322 #define TW5864_AUDIO_BUF_FLAG (0xffff << 16) 1323 1324 #define TW5864_IIC 0x18014 1325 /* Define controls in register TW5864_IIC */ 1326 /* register data */ 1327 #define TW5864_IIC_DATA 0x00ff 1328 #define TW5864_IIC_REG_ADDR_SHIFT 8 1329 /* register addr */ 1330 #define TW5864_IIC_REG_ADDR (0xff << 8) 1331 /* rd/wr flag rd=1,wr=0 */ 1332 #define TW5864_IIC_RW BIT(16) 1333 #define TW5864_IIC_DEV_ADDR_SHIFT 17 1334 /* device addr */ 1335 #define TW5864_IIC_DEV_ADDR (0x7f << 17) 1336 /* 1337 * iic done, software kick off one time iic transaction through setting this 1338 * bit to 1. Then poll this bit, value 1 indicate iic transaction have 1339 * completed, if read, valid data have been stored in iic_data 1340 */ 1341 #define TW5864_IIC_DONE BIT(24) 1342 1343 #define TW5864_RST_AND_IF_INFO 0x18018 1344 /* Define controls in register TW5864_RST_AND_IF_INFO */ 1345 /* application software soft reset */ 1346 #define TW5864_APP_SOFT_RST BIT(0) 1347 #define TW5864_PCI_INF_VERSION_SHIFT 16 1348 /* PCI interface version, read only */ 1349 #define TW5864_PCI_INF_VERSION (0xffff << 16) 1350 1351 /* vlc stream crc value, it is calculated in pci module */ 1352 #define TW5864_VLC_CRC_REG 0x1801c 1353 /* 1354 * vlc max length, it is defined by software based on software assign memory 1355 * space for vlc 1356 */ 1357 #define TW5864_VLC_MAX_LENGTH 0x18020 1358 /* vlc length of one frame */ 1359 #define TW5864_VLC_LENGTH 0x18024 1360 /* vlc original crc value */ 1361 #define TW5864_VLC_INTRA_CRC_I_REG 0x18028 1362 /* vlc original crc value */ 1363 #define TW5864_VLC_INTRA_CRC_O_REG 0x1802c 1364 /* mv stream crc value, it is calculated in pci module */ 1365 #define TW5864_VLC_PAR_CRC_REG 0x18030 1366 /* mv length */ 1367 #define TW5864_VLC_PAR_LENGTH_REG 0x18034 1368 /* mv original crc value */ 1369 #define TW5864_VLC_PAR_I_REG 0x18038 1370 /* mv original crc value */ 1371 #define TW5864_VLC_PAR_O_REG 0x1803c 1372 1373 /* 1374 * Configuration register for 9[or 10] CIFs or 1D1+15QCIF Preview mode. 1375 * PREV_PCI_ENB_CHN[0] Enable 9th preview channel (9CIF prev) or 1D1 channel in 1376 * (1D1+15QCIF prev) 1377 * PREV_PCI_ENB_CHN[1] Enable 10th preview channel 1378 */ 1379 #define TW5864_PREV_PCI_ENB_CHN 0x18040 1380 /* Description skipped. */ 1381 #define TW5864_PREV_FRAME_FORMAT_IN 0x18044 1382 /* IIC enable */ 1383 #define TW5864_IIC_ENB 0x18048 1384 /* 1385 * Timer interrupt interval 1386 * 0 1ms 1387 * 1 2ms 1388 * 2 4ms 1389 * 3 8ms 1390 */ 1391 #define TW5864_PCI_INTTM_SCALE 0x1804c 1392 1393 /* 1394 * The above register is pci base address registers. Application software will 1395 * initialize them to tell chip where the corresponding stream will be dumped 1396 * to. Application software will select appropriate base address interval based 1397 * on the stream length. 1398 */ 1399 /* VLC stream base address */ 1400 #define TW5864_VLC_STREAM_BASE_ADDR 0x18080 1401 /* MV stream base address */ 1402 #define TW5864_MV_STREAM_BASE_ADDR 0x18084 1403 /* 0x180a0 – 0x180bc: audio burst base address. Skipped. */ 1404 /* 0x180c0 ~ 0x180dc – JPEG Push Mode Buffer Base Address. Skipped. */ 1405 /* 0x18100 – 0x1817c: preview burst base address. Skipped. */ 1406 1407 /* 0x80000 ~ 0x87fff -- DDR Burst RW Register Map */ 1408 #define TW5864_DDR_CTL 0x80000 1409 /* Define controls in register TW5864_DDR_CTL */ 1410 #define TW5864_BRST_LENGTH_SHIFT 2 1411 /* Length of 32-bit data burst */ 1412 #define TW5864_BRST_LENGTH (0x3fff << 2) 1413 /* 1414 * Burst Read/Write 1415 * 0 Read Burst from DDR 1416 * 1 Write Burst to DDR 1417 */ 1418 #define TW5864_BRST_RW BIT(16) 1419 /* Begin a new DDR Burst. This bit is self cleared */ 1420 #define TW5864_NEW_BRST_CMD BIT(17) 1421 /* DDR Burst End Flag */ 1422 #define TW5864_BRST_END BIT(24) 1423 /* Enable Error Interrupt for Single DDR Access */ 1424 #define TW5864_SING_ERR_INTR BIT(25) 1425 /* Enable Error Interrupt for Burst DDR Access */ 1426 #define TW5864_BRST_ERR_INTR BIT(26) 1427 /* Enable Interrupt for End of DDR Burst Access */ 1428 #define TW5864_BRST_END_INTR BIT(27) 1429 /* DDR Single Access Error Flag */ 1430 #define TW5864_SINGLE_ERR BIT(28) 1431 /* DDR Single Access Busy Flag */ 1432 #define TW5864_SINGLE_BUSY BIT(29) 1433 /* DDR Burst Access Error Flag */ 1434 #define TW5864_BRST_ERR BIT(30) 1435 /* DDR Burst Access Busy Flag */ 1436 #define TW5864_BRST_BUSY BIT(31) 1437 1438 /* [27:0] DDR Access Address. Bit [1:0] has to be 0 */ 1439 #define TW5864_DDR_ADDR 0x80004 1440 /* DDR Access Internal Buffer Address. Bit [1:0] has to be 0 */ 1441 #define TW5864_DPR_BUF_ADDR 0x80008 1442 /* SRAM Buffer MPI Access Space. Totally 16 KB */ 1443 #define TW5864_DPR_BUF_START 0x84000 1444 /* 0x84000 - 0x87ffc */ 1445 #define TW5864_DPR_BUF_SIZE 0x4000 1446 1447 /* Indirect Map Space */ 1448 /* 1449 * The indirect space is accessed through 0xb800 ~ 0xb807 registers in direct 1450 * access space 1451 */ 1452 /* Analog Video / Audio Decoder / Encoder */ 1453 /* Allowed channel values: [0; 3] */ 1454 /* Read-only register */ 1455 #define TW5864_INDIR_VIN_0(channel) (0x000 + channel * 0x010) 1456 /* Define controls in register TW5864_INDIR_VIN_0 */ 1457 /* 1458 * 1 Video not present. (sync is not detected in number of consecutive line 1459 * periods specified by MISSCNT register) 1460 * 0 Video detected. 1461 */ 1462 #define TW5864_INDIR_VIN_0_VDLOSS BIT(7) 1463 /* 1464 * 1 Horizontal sync PLL is locked to the incoming video source. 1465 * 0 Horizontal sync PLL is not locked. 1466 */ 1467 #define TW5864_INDIR_VIN_0_HLOCK BIT(6) 1468 /* 1469 * 1 Sub-carrier PLL is locked to the incoming video source. 1470 * 0 Sub-carrier PLL is not locked. 1471 */ 1472 #define TW5864_INDIR_VIN_0_SLOCK BIT(5) 1473 /* 1474 * 1 Even field is being decoded. 1475 * 0 Odd field is being decoded. 1476 */ 1477 #define TW5864_INDIR_VIN_0_FLD BIT(4) 1478 /* 1479 * 1 Vertical logic is locked to the incoming video source. 1480 * 0 Vertical logic is not locked. 1481 */ 1482 #define TW5864_INDIR_VIN_0_VLOCK BIT(3) 1483 /* 1484 * 1 No color burst signal detected. 1485 * 0 Color burst signal detected. 1486 */ 1487 #define TW5864_INDIR_VIN_0_MONO BIT(1) 1488 /* 1489 * 0 60Hz source detected 1490 * 1 50Hz source detected 1491 * The actual vertical scanning frequency depends on the current standard 1492 * invoked. 1493 */ 1494 #define TW5864_INDIR_VIN_0_DET50 BIT(0) 1495 1496 #define TW5864_INDIR_VIN_1(channel) (0x001 + channel * 0x010) 1497 /* VCR signal indicator. Read-only. */ 1498 #define TW5864_INDIR_VIN_1_VCR BIT(7) 1499 /* Weak signal indicator 2. Read-only. */ 1500 #define TW5864_INDIR_VIN_1_WKAIR BIT(6) 1501 /* Weak signal indicator controlled by WKTH. Read-only. */ 1502 #define TW5864_INDIR_VIN_1_WKAIR1 BIT(5) 1503 /* 1504 * 1 = Standard signal 1505 * 0 = Non-standard signal 1506 * Read-only 1507 */ 1508 #define TW5864_INDIR_VIN_1_VSTD BIT(4) 1509 /* 1510 * 1 = Non-interlaced signal 1511 * 0 = interlaced signal 1512 * Read-only 1513 */ 1514 #define TW5864_INDIR_VIN_1_NINTL BIT(3) 1515 /* 1516 * Vertical Sharpness Control. Writable. 1517 * 0 = None (default) 1518 * 7 = Highest 1519 * **Note: VSHP must be set to ‘0’ if COMB = 0 1520 */ 1521 #define TW5864_INDIR_VIN_1_VSHP 0x07 1522 1523 /* HDELAY_XY[7:0] */ 1524 #define TW5864_INDIR_VIN_2_HDELAY_XY_LO(channel) (0x002 + channel * 0x010) 1525 /* HACTIVE_XY[7:0] */ 1526 #define TW5864_INDIR_VIN_3_HACTIVE_XY_LO(channel) (0x003 + channel * 0x010) 1527 /* VDELAY_XY[7:0] */ 1528 #define TW5864_INDIR_VIN_4_VDELAY_XY_LO(channel) (0x004 + channel * 0x010) 1529 /* VACTIVE_XY[7:0] */ 1530 #define TW5864_INDIR_VIN_5_VACTIVE_XY_LO(channel) (0x005 + channel * 0x010) 1531 1532 #define TW5864_INDIR_VIN_6(channel) (0x006 + channel * 0x010) 1533 /* Define controls in register TW5864_INDIR_VIN_6 */ 1534 #define TW5864_INDIR_VIN_6_HDELAY_XY_HI 0x03 1535 #define TW5864_INDIR_VIN_6_HACTIVE_XY_HI_SHIFT 2 1536 #define TW5864_INDIR_VIN_6_HACTIVE_XY_HI (0x03 << 2) 1537 #define TW5864_INDIR_VIN_6_VDELAY_XY_HI BIT(4) 1538 #define TW5864_INDIR_VIN_6_VACTIVE_XY_HI BIT(5) 1539 1540 /* 1541 * HDELAY_XY This 10bit register defines the starting location of horizontal 1542 * active pixel for display / record path. A unit is 1 pixel. The default value 1543 * is 0x00f for NTSC and 0x00a for PAL. 1544 * 1545 * HACTIVE_XY This 10bit register defines the number of horizontal active pixel 1546 * for display / record path. A unit is 1 pixel. The default value is decimal 1547 * 720. 1548 * 1549 * VDELAY_XY This 9bit register defines the starting location of vertical 1550 * active for display / record path. A unit is 1 line. The default value is 1551 * decimal 6. 1552 * 1553 * VACTIVE_XY This 9bit register defines the number of vertical active lines 1554 * for display / record path. A unit is 1 line. The default value is decimal 1555 * 240. 1556 */ 1557 1558 /* HUE These bits control the color hue as 2's complement number. They have 1559 * value from +36o (7Fh) to -36o (80h) with an increment of 2.8o. The 2 LSB has 1560 * no effect. The positive value gives greenish tone and negative value gives 1561 * purplish tone. The default value is 0o (00h). This is effective only on NTSC 1562 * system. The default is 00h. 1563 */ 1564 #define TW5864_INDIR_VIN_7_HUE(channel) (0x007 + channel * 0x010) 1565 1566 #define TW5864_INDIR_VIN_8(channel) (0x008 + channel * 0x010) 1567 /* Define controls in register TW5864_INDIR_VIN_8 */ 1568 /* 1569 * This bit controls the center frequency of the peaking filter. 1570 * The corresponding gain adjustment is HFLT. 1571 * 0 Low 1572 * 1 center 1573 */ 1574 #define TW5864_INDIR_VIN_8_SCURVE BIT(7) 1575 /* CTI level selection. The default is 1. 1576 * 0 None 1577 * 3 Highest 1578 */ 1579 #define TW5864_INDIR_VIN_8_CTI_SHIFT 4 1580 #define TW5864_INDIR_VIN_8_CTI (0x03 << 4) 1581 1582 /* 1583 * These bits control the amount of sharpness enhancement on the luminance 1584 * signals. There are 16 levels of control with "0" having no effect on the 1585 * output image. 1 through 15 provides sharpness enhancement with "F" being the 1586 * strongest. The default is 1. 1587 */ 1588 #define TW5864_INDIR_VIN_8_SHARPNESS 0x0f 1589 1590 /* 1591 * These bits control the luminance contrast gain. A value of 100 (64h) has a 1592 * gain of 1. The range adjustment is from 0% to 255% at 1% per step. The 1593 * default is 64h. 1594 */ 1595 #define TW5864_INDIR_VIN_9_CNTRST(channel) (0x009 + channel * 0x010) 1596 1597 /* 1598 * These bits control the brightness. They have value of –128 to 127 in 2's 1599 * complement form. Positive value increases brightness. A value 0 has no 1600 * effect on the data. The default is 00h. 1601 */ 1602 #define TW5864_INDIR_VIN_A_BRIGHT(channel) (0x00a + channel * 0x010) 1603 1604 /* 1605 * These bits control the digital gain adjustment to the U (or Cb) component of 1606 * the digital video signal. The color saturation can be adjusted by adjusting 1607 * the U and V color gain components by the same amount in the normal 1608 * situation. The U and V can also be adjusted independently to provide greater 1609 * flexibility. The range of adjustment is 0 to 200%. A value of 128 (80h) has 1610 * gain of 100%. The default is 80h. 1611 */ 1612 #define TW5864_INDIR_VIN_B_SAT_U(channel) (0x00b + channel * 0x010) 1613 1614 /* 1615 * These bits control the digital gain adjustment to the V (or Cr) component of 1616 * the digital video signal. The color saturation can be adjusted by adjusting 1617 * the U and V color gain components by the same amount in the normal 1618 * situation. The U and V can also be adjusted independently to provide greater 1619 * flexibility. The range of adjustment is 0 to 200%. A value of 128 (80h) has 1620 * gain of 100%. The default is 80h. 1621 */ 1622 #define TW5864_INDIR_VIN_C_SAT_V(channel) (0x00c + channel * 0x010) 1623 1624 /* Read-only */ 1625 #define TW5864_INDIR_VIN_D(channel) (0x00d + channel * 0x010) 1626 /* Define controls in register TW5864_INDIR_VIN_D */ 1627 /* Macrovision color stripe detection may be un-reliable */ 1628 #define TW5864_INDIR_VIN_D_CSBAD BIT(3) 1629 /* Macrovision AGC pulse detected */ 1630 #define TW5864_INDIR_VIN_D_MCVSN BIT(2) 1631 /* Macrovision color stripe protection burst detected */ 1632 #define TW5864_INDIR_VIN_D_CSTRIPE BIT(1) 1633 /* 1634 * This bit is valid only when color stripe protection is detected, i.e. if 1635 * CSTRIPE=1, 1636 * 1 Type 2 color stripe protection 1637 * 0 Type 3 color stripe protection 1638 */ 1639 #define TW5864_INDIR_VIN_D_CTYPE2 BIT(0) 1640 1641 /* Read-only */ 1642 #define TW5864_INDIR_VIN_E(channel) (0x00e + channel * 0x010) 1643 /* Define controls in register TW5864_INDIR_VIN_E */ 1644 /* 1645 * Read-only. 1646 * 0 Idle 1647 * 1 Detection in progress 1648 */ 1649 #define TW5864_INDIR_VIN_E_DETSTUS BIT(7) 1650 /* 1651 * STDNOW Current standard invoked 1652 * 0 NTSC (M) 1653 * 1 PAL (B, D, G, H, I) 1654 * 2 SECAM 1655 * 3 NTSC4.43 1656 * 4 PAL (M) 1657 * 5 PAL (CN) 1658 * 6 PAL 60 1659 * 7 Not valid 1660 */ 1661 #define TW5864_INDIR_VIN_E_STDNOW_SHIFT 4 1662 #define TW5864_INDIR_VIN_E_STDNOW (0x07 << 4) 1663 1664 /* 1665 * 1 Disable the shadow registers 1666 * 0 Enable VACTIVE and HDELAY shadow registers value depending on STANDARD. 1667 * (Default) 1668 */ 1669 #define TW5864_INDIR_VIN_E_ATREG BIT(3) 1670 /* 1671 * STANDARD Standard selection 1672 * 0 NTSC (M) 1673 * 1 PAL (B, D, G, H, I) 1674 * 2 SECAM 1675 * 3 NTSC4.43 1676 * 4 PAL (M) 1677 * 5 PAL (CN) 1678 * 6 PAL 60 1679 * 7 Auto detection (Default) 1680 */ 1681 #define TW5864_INDIR_VIN_E_STANDARD 0x07 1682 1683 #define TW5864_INDIR_VIN_F(channel) (0x00f + channel * 0x010) 1684 /* Define controls in register TW5864_INDIR_VIN_F */ 1685 /* 1686 * 1 Writing 1 to this bit will manually initiate the auto format detection 1687 * process. This bit is a self-clearing bit 1688 * 0 Manual initiation of auto format detection is done. (Default) 1689 */ 1690 #define TW5864_INDIR_VIN_F_ATSTART BIT(7) 1691 /* Enable recognition of PAL60 (Default) */ 1692 #define TW5864_INDIR_VIN_F_PAL60EN BIT(6) 1693 /* Enable recognition of PAL (CN). (Default) */ 1694 #define TW5864_INDIR_VIN_F_PALCNEN BIT(5) 1695 /* Enable recognition of PAL (M). (Default) */ 1696 #define TW5864_INDIR_VIN_F_PALMEN BIT(4) 1697 /* Enable recognition of NTSC 4.43. (Default) */ 1698 #define TW5864_INDIR_VIN_F_NTSC44EN BIT(3) 1699 /* Enable recognition of SECAM. (Default) */ 1700 #define TW5864_INDIR_VIN_F_SECAMEN BIT(2) 1701 /* Enable recognition of PAL (B, D, G, H, I). (Default) */ 1702 #define TW5864_INDIR_VIN_F_PALBEN BIT(1) 1703 /* Enable recognition of NTSC (M). (Default) */ 1704 #define TW5864_INDIR_VIN_F_NTSCEN BIT(0) 1705 1706 /* Some registers skipped. */ 1707 1708 /* Use falling edge to sample VD1-VD4 from 54 MHz to 108 MHz */ 1709 #define TW5864_INDIR_VD_108_POL 0x041 1710 #define TW5864_INDIR_VD_108_POL_VD12 BIT(0) 1711 #define TW5864_INDIR_VD_108_POL_VD34 BIT(1) 1712 #define TW5864_INDIR_VD_108_POL_BOTH \ 1713 (TW5864_INDIR_VD_108_POL_VD12 | TW5864_INDIR_VD_108_POL_VD34) 1714 1715 /* Some registers skipped. */ 1716 1717 /* 1718 * Audio Input ADC gain control 1719 * 0 0.25 1720 * 1 0.31 1721 * 2 0.38 1722 * 3 0.44 1723 * 4 0.50 1724 * 5 0.63 1725 * 6 0.75 1726 * 7 0.88 1727 * 8 1.00 (default) 1728 * 9 1.25 1729 * 10 1.50 1730 * 11 1.75 1731 * 12 2.00 1732 * 13 2.25 1733 * 14 2.50 1734 * 15 2.75 1735 */ 1736 /* [3:0] channel 0, [7:4] channel 1 */ 1737 #define TW5864_INDIR_AIGAIN1 0x060 1738 /* [3:0] channel 2, [7:4] channel 3 */ 1739 #define TW5864_INDIR_AIGAIN2 0x061 1740 1741 /* Some registers skipped */ 1742 1743 #define TW5864_INDIR_AIN_0x06D 0x06d 1744 /* Define controls in register TW5864_INDIR_AIN_0x06D */ 1745 /* 1746 * LAWMD Select u-Law/A-Law/PCM/SB data output format on ADATR and ADATM pin. 1747 * 0 PCM output (default) 1748 * 1 SB (Signed MSB bit in PCM data is inverted) output 1749 * 2 u-Law output 1750 * 3 A-Law output 1751 */ 1752 #define TW5864_INDIR_AIN_LAWMD_SHIFT 6 1753 #define TW5864_INDIR_AIN_LAWMD (0x03 << 6) 1754 /* 1755 * Disable the mixing ratio value for all audio. 1756 * 0 Apply individual mixing ratio value for each audio (default) 1757 * 1 Apply nominal value for all audio commonly 1758 */ 1759 #define TW5864_INDIR_AIN_MIX_DERATIO BIT(5) 1760 /* 1761 * Enable the mute function for audio channel AINn when n is 0 to 3. It effects 1762 * only for mixing. When n = 4, it enable the mute function of the playback 1763 * audio input. It effects only for single chip or the last stage chip 1764 * 0 Normal 1765 * 1 Muted (default) 1766 */ 1767 #define TW5864_INDIR_AIN_MIX_MUTE 0x1f 1768 1769 /* Some registers skipped */ 1770 1771 #define TW5864_INDIR_AIN_0x0E3 0x0e3 1772 /* Define controls in register TW5864_INDIR_AIN_0x0E3 */ 1773 /* 1774 * ADATP signal is coming from external ADPCM decoder, instead of on-chip ADPCM 1775 * decoder 1776 */ 1777 #define TW5864_INDIR_AIN_0x0E3_EXT_ADATP BIT(7) 1778 /* ACLKP output signal polarity inverse */ 1779 #define TW5864_INDIR_AIN_0x0E3_ACLKPPOLO BIT(6) 1780 /* 1781 * ACLKR input signal polarity inverse. 1782 * 0 Not inversed (Default) 1783 * 1 Inversed 1784 */ 1785 #define TW5864_INDIR_AIN_0x0E3_ACLKRPOL BIT(5) 1786 /* 1787 * ACLKP input signal polarity inverse. 1788 * 0 Not inversed (Default) 1789 * 1 Inversed 1790 */ 1791 #define TW5864_INDIR_AIN_0x0E3_ACLKPPOLI BIT(4) 1792 /* 1793 * ACKI [21:0] control automatic set up with AFMD registers 1794 * This mode is only effective when ACLKRMASTER=1 1795 * 0 ACKI [21:0] registers set up ACKI control 1796 * 1 ACKI control is automatically set up by AFMD register values 1797 */ 1798 #define TW5864_INDIR_AIN_0x0E3_AFAUTO BIT(3) 1799 /* 1800 * AFAUTO control mode 1801 * 0 8kHz setting (Default) 1802 * 1 16kHz setting 1803 * 2 32kHz setting 1804 * 3 44.1kHz setting 1805 * 4 48kHz setting 1806 */ 1807 #define TW5864_INDIR_AIN_0x0E3_AFMD 0x07 1808 1809 #define TW5864_INDIR_AIN_0x0E4 0x0e4 1810 /* Define controls in register TW5864_INDIR_AIN_0x0ED */ 1811 /* 1812 * 8bit I2S Record output mode. 1813 * 0 L/R half length separated output (Default). 1814 * 1 One continuous packed output equal to DSP output format. 1815 */ 1816 #define TW5864_INDIR_AIN_0x0E4_I2S8MODE BIT(7) 1817 /* 1818 * Audio Clock Master ACLKR output wave format. 1819 * 0 High periods is one 27MHz clock period (default). 1820 * 1 Almost duty 50-50% clock output on ACLKR pin. If this mode is selected, two 1821 * times bigger number value need to be set up on the ACKI register. If 1822 * AFAUTO=1, ACKI control is automatically set up even if MASCKMD=1. 1823 */ 1824 #define TW5864_INDIR_AIN_0x0E4_MASCKMD BIT(6) 1825 /* Playback ACLKP/ASYNP/ADATP input data MSB-LSB swapping */ 1826 #define TW5864_INDIR_AIN_0x0E4_PBINSWAP BIT(5) 1827 /* 1828 * ASYNR input signal delay. 1829 * 0 No delay 1830 * 1 Add one 27MHz period delay in ASYNR signal input 1831 */ 1832 #define TW5864_INDIR_AIN_0x0E4_ASYNRDLY BIT(4) 1833 /* 1834 * ASYNP input signal delay. 1835 * 0 no delay 1836 * 1 add one 27MHz period delay in ASYNP signal input 1837 */ 1838 #define TW5864_INDIR_AIN_0x0E4_ASYNPDLY BIT(3) 1839 /* 1840 * ADATP input data delay by one ACLKP clock. 1841 * 0 No delay (Default). This is for I2S type 1T delay input interface. 1842 * 1 Add 1 ACLKP clock delay in ADATP input data. This is for left-justified 1843 * type 0T delay input interface. 1844 */ 1845 #define TW5864_INDIR_AIN_0x0E4_ADATPDLY BIT(2) 1846 /* 1847 * Select u-Law/A-Law/PCM/SB data input format on ADATP pin. 1848 * 0 PCM input (Default) 1849 * 1 SB (Signed MSB bit in PCM data is inverted) input 1850 * 2 u-Law input 1851 * 3 A-Law input 1852 */ 1853 #define TW5864_INDIR_AIN_0x0E4_INLAWMD 0x03 1854 1855 /* 1856 * Enable state register updating and interrupt request of audio AIN5 detection 1857 * for each input 1858 */ 1859 #define TW5864_INDIR_AIN_A5DETENA 0x0e5 1860 1861 /* Some registers skipped */ 1862 1863 /* 1864 * [7:3]: DEV_ID The TW5864 product ID code is 01000 1865 * [2:0]: REV_ID The revision number is 0h 1866 */ 1867 #define TW5864_INDIR_ID 0x0fe 1868 1869 #define TW5864_INDIR_IN_PIC_WIDTH(channel) (0x200 + 4 * channel) 1870 #define TW5864_INDIR_IN_PIC_HEIGHT(channel) (0x201 + 4 * channel) 1871 #define TW5864_INDIR_OUT_PIC_WIDTH(channel) (0x202 + 4 * channel) 1872 #define TW5864_INDIR_OUT_PIC_HEIGHT(channel) (0x203 + 4 * channel) 1873 1874 /* Some registers skipped */ 1875 1876 #define TW5864_INDIR_CROP_ETC 0x260 1877 /* Define controls in register TW5864_INDIR_CROP_ETC */ 1878 /* Enable cropping from 720 to 704 */ 1879 #define TW5864_INDIR_CROP_ETC_CROP_EN 0x4 1880 1881 /* 1882 * Interrupt status register from the front-end. Write "1" to each bit to clear 1883 * the interrupt 1884 * 15:0 Motion detection interrupt for channel 0 ~ 15 1885 * 31:16 Night detection interrupt for channel 0 ~ 15 1886 * 47:32 Blind detection interrupt for channel 0 ~ 15 1887 * 63:48 No video interrupt for channel 0 ~ 15 1888 * 79:64 Line mode underflow interrupt for channel 0 ~ 15 1889 * 95:80 Line mode overflow interrupt for channel 0 ~ 15 1890 */ 1891 /* 0x2d0~0x2d7: [63:0] bits */ 1892 #define TW5864_INDIR_INTERRUPT1 0x2d0 1893 /* 0x2e0~0x2e3: [95:64] bits */ 1894 #define TW5864_INDIR_INTERRUPT2 0x2e0 1895 1896 /* 1897 * Interrupt mask register for interrupts in 0x2d0 ~ 0x2d7 1898 * 15:0 Motion detection interrupt for channel 0 ~ 15 1899 * 31:16 Night detection interrupt for channel 0 ~ 15 1900 * 47:32 Blind detection interrupt for channel 0 ~ 15 1901 * 63:48 No video interrupt for channel 0 ~ 15 1902 * 79:64 Line mode underflow interrupt for channel 0 ~ 15 1903 * 95:80 Line mode overflow interrupt for channel 0 ~ 15 1904 */ 1905 /* 0x2d8~0x2df: [63:0] bits */ 1906 #define TW5864_INDIR_INTERRUPT_MASK1 0x2d8 1907 /* 0x2e8~0x2eb: [95:64] bits */ 1908 #define TW5864_INDIR_INTERRUPT_MASK2 0x2e8 1909 1910 /* [11:0]: Interrupt summary register for interrupts & interrupt mask from in 1911 * 0x2d0 ~ 0x2d7 and 0x2d8 ~ 0x2df 1912 * bit 0: interrupt occurs in 0x2d0 & 0x2d8 1913 * bit 1: interrupt occurs in 0x2d1 & 0x2d9 1914 * bit 2: interrupt occurs in 0x2d2 & 0x2da 1915 * bit 3: interrupt occurs in 0x2d3 & 0x2db 1916 * bit 4: interrupt occurs in 0x2d4 & 0x2dc 1917 * bit 5: interrupt occurs in 0x2d5 & 0x2dd 1918 * bit 6: interrupt occurs in 0x2d6 & 0x2de 1919 * bit 7: interrupt occurs in 0x2d7 & 0x2df 1920 * bit 8: interrupt occurs in 0x2e0 & 0x2e8 1921 * bit 9: interrupt occurs in 0x2e1 & 0x2e9 1922 * bit 10: interrupt occurs in 0x2e2 & 0x2ea 1923 * bit 11: interrupt occurs in 0x2e3 & 0x2eb 1924 */ 1925 #define TW5864_INDIR_INTERRUPT_SUMMARY 0x2f0 1926 1927 /* Motion / Blind / Night Detection */ 1928 /* valid value for channel is [0:15] */ 1929 #define TW5864_INDIR_DETECTION_CTL0(channel) (0x300 + channel * 0x08) 1930 /* Define controls in register TW5864_INDIR_DETECTION_CTL0 */ 1931 /* 1932 * Disable the motion and blind detection. 1933 * 0 Enable motion and blind detection (default) 1934 * 1 Disable motion and blind detection 1935 */ 1936 #define TW5864_INDIR_DETECTION_CTL0_MD_DIS BIT(5) 1937 /* 1938 * Request to start motion detection on manual trigger mode 1939 * 0 None Operation (default) 1940 * 1 Request to start motion detection 1941 */ 1942 #define TW5864_INDIR_DETECTION_CTL0_MD_STRB BIT(3) 1943 /* 1944 * Select the trigger mode of motion detection 1945 * 0 Automatic trigger mode of motion detection (default) 1946 * 1 Manual trigger mode for motion detection 1947 */ 1948 #define TW5864_INDIR_DETECTION_CTL0_MD_STRB_EN BIT(2) 1949 /* 1950 * Define the threshold of cell for blind detection. 1951 * 0 Low threshold (More sensitive) (default) 1952 * : : 1953 * 3 High threshold (Less sensitive) 1954 */ 1955 #define TW5864_INDIR_DETECTION_CTL0_BD_CELSENS 0x03 1956 1957 #define TW5864_INDIR_DETECTION_CTL1(channel) (0x301 + channel * 0x08) 1958 /* Define controls in register TW5864_INDIR_DETECTION_CTL1 */ 1959 /* 1960 * Control the temporal sensitivity of motion detector. 1961 * 0 More Sensitive (default) 1962 * : : 1963 * 15 Less Sensitive 1964 */ 1965 #define TW5864_INDIR_DETECTION_CTL1_MD_TMPSENS_SHIFT 4 1966 #define TW5864_INDIR_DETECTION_CTL1_MD_TMPSENS (0x0f << 4) 1967 /* 1968 * Adjust the horizontal starting position for motion detection 1969 * 0 0 pixel (default) 1970 * : : 1971 * 15 15 pixels 1972 */ 1973 #define TW5864_INDIR_DETECTION_CTL1_MD_PIXEL_OS 0x0f 1974 1975 #define TW5864_INDIR_DETECTION_CTL2(channel) (0x302 + channel * 0x08) 1976 /* Define controls in register TW5864_INDIR_DETECTION_CTL2 */ 1977 /* 1978 * Control the updating time of reference field for motion detection. 1979 * 0 Update reference field every field (default) 1980 * 1 Update reference field according to MD_SPEED 1981 */ 1982 #define TW5864_INDIR_DETECTION_CTL2_MD_REFFLD BIT(7) 1983 /* 1984 * Select the field for motion detection. 1985 * 0 Detecting motion for only odd field (default) 1986 * 1 Detecting motion for only even field 1987 * 2 Detecting motion for any field 1988 * 3 Detecting motion for both odd and even field 1989 */ 1990 #define TW5864_INDIR_DETECTION_CTL2_MD_FIELD_SHIFT 5 1991 #define TW5864_INDIR_DETECTION_CTL2_MD_FIELD (0x03 << 5) 1992 /* 1993 * Control the level sensitivity of motion detector. 1994 * 0 More sensitive (default) 1995 * : : 1996 * 15 Less sensitive 1997 */ 1998 #define TW5864_INDIR_DETECTION_CTL2_MD_LVSENS 0x1f 1999 2000 #define TW5864_INDIR_DETECTION_CTL3(channel) (0x303 + channel * 0x08) 2001 /* Define controls in register TW5864_INDIR_DETECTION_CTL3 */ 2002 /* 2003 * Define the threshold of sub-cell number for motion detection. 2004 * 0 Motion is detected if 1 sub-cell has motion (More sensitive) (default) 2005 * 1 Motion is detected if 2 sub-cells have motion 2006 * 2 Motion is detected if 3 sub-cells have motion 2007 * 3 Motion is detected if 4 sub-cells have motion (Less sensitive) 2008 */ 2009 #define TW5864_INDIR_DETECTION_CTL3_MD_CELSENS_SHIFT 6 2010 #define TW5864_INDIR_DETECTION_CTL3_MD_CELSENS (0x03 << 6) 2011 /* 2012 * Control the velocity of motion detector. 2013 * Large value is suitable for slow motion detection. 2014 * In MD_DUAL_EN = 1, MD_SPEED should be limited to 0 ~ 31. 2015 * 0 1 field intervals (default) 2016 * 1 2 field intervals 2017 * : : 2018 * 61 62 field intervals 2019 * 62 63 field intervals 2020 * 63 Not supported 2021 */ 2022 #define TW5864_INDIR_DETECTION_CTL3_MD_SPEED 0x3f 2023 2024 #define TW5864_INDIR_DETECTION_CTL4(channel) (0x304 + channel * 0x08) 2025 /* Define controls in register TW5864_INDIR_DETECTION_CTL4 */ 2026 /* 2027 * Control the spatial sensitivity of motion detector. 2028 * 0 More Sensitive (default) 2029 * : : 2030 * 15 Less Sensitive 2031 */ 2032 #define TW5864_INDIR_DETECTION_CTL4_MD_SPSENS_SHIFT 4 2033 #define TW5864_INDIR_DETECTION_CTL4_MD_SPSENS (0x0f << 4) 2034 /* 2035 * Define the threshold of level for blind detection. 2036 * 0 Low threshold (More sensitive) (default) 2037 * : : 2038 * 15 High threshold (Less sensitive) 2039 */ 2040 #define TW5864_INDIR_DETECTION_CTL4_BD_LVSENS 0x0f 2041 2042 #define TW5864_INDIR_DETECTION_CTL5(channel) (0x305 + channel * 0x08) 2043 /* 2044 * Define the threshold of temporal sensitivity for night detection. 2045 * 0 Low threshold (More sensitive) (default) 2046 * : : 2047 * 15 High threshold (Less sensitive) 2048 */ 2049 #define TW5864_INDIR_DETECTION_CTL5_ND_TMPSENS_SHIFT 4 2050 #define TW5864_INDIR_DETECTION_CTL5_ND_TMPSENS (0x0f << 4) 2051 /* 2052 * Define the threshold of level for night detection. 2053 * 0 Low threshold (More sensitive) (default) 2054 * : : 2055 * 3 High threshold (Less sensitive) 2056 */ 2057 #define TW5864_INDIR_DETECTION_CTL5_ND_LVSENS 0x0f 2058 2059 /* 2060 * [11:0] The base address of the motion detection buffer. This address is in 2061 * unit of 64K bytes. The generated DDR address will be {MD_BASE_ADDR, 2062 * 16"h0000}. The default value should be 12"h000 2063 */ 2064 #define TW5864_INDIR_MD_BASE_ADDR 0x380 2065 2066 /* 2067 * This controls the channel of the motion detection result shown in register 2068 * 0x3a0 ~ 0x3b7. Before reading back motion result, always set this first. 2069 */ 2070 #define TW5864_INDIR_RGR_MOTION_SEL 0x382 2071 2072 /* [15:0] MD strobe has been performed at channel n (read only) */ 2073 #define TW5864_INDIR_MD_STRB 0x386 2074 /* NO_VIDEO Detected from channel n (read only) */ 2075 #define TW5864_INDIR_NOVID_DET 0x388 2076 /* Motion Detected from channel n (read only) */ 2077 #define TW5864_INDIR_MD_DET 0x38a 2078 /* Blind Detected from channel n (read only) */ 2079 #define TW5864_INDIR_BD_DET 0x38c 2080 /* Night Detected from channel n (read only) */ 2081 #define TW5864_INDIR_ND_DET 0x38e 2082 2083 /* 192 bit motion flag of the channel specified by RGR_MOTION_SEL in 0x382 */ 2084 #define TW5864_INDIR_MOTION_FLAG 0x3a0 2085 #define TW5864_INDIR_MOTION_FLAG_BYTE_COUNT 24 2086 2087 /* 2088 * [9:0] The motion cell count of a specific channel selected by 0x382. This is 2089 * for DI purpose 2090 */ 2091 #define TW5864_INDIR_MD_DI_CNT 0x3b8 2092 /* The motion detection cell sensitivity for DI purpose */ 2093 #define TW5864_INDIR_MD_DI_CELLSENS 0x3ba 2094 /* The motion detection threshold level for DI purpose */ 2095 #define TW5864_INDIR_MD_DI_LVSENS 0x3bb 2096 2097 /* 192 bit motion mask of the channel specified by MASK_CH_SEL in 0x3fe */ 2098 #define TW5864_INDIR_MOTION_MASK 0x3e0 2099 #define TW5864_INDIR_MOTION_MASK_BYTE_COUNT 24 2100 2101 /* [4:0] The channel selection to access masks in 0x3e0 ~ 0x3f7 */ 2102 #define TW5864_INDIR_MASK_CH_SEL 0x3fe 2103 2104 /* Clock PLL / Analog IP Control */ 2105 /* Some registers skipped */ 2106 2107 #define TW5864_INDIR_DDRA_DLL_DQS_SEL0 0xee6 2108 #define TW5864_INDIR_DDRA_DLL_DQS_SEL1 0xee7 2109 #define TW5864_INDIR_DDRA_DLL_CLK90_SEL 0xee8 2110 #define TW5864_INDIR_DDRA_DLL_TEST_SEL_AND_TAP_S 0xee9 2111 2112 #define TW5864_INDIR_DDRB_DLL_DQS_SEL0 0xeeb 2113 #define TW5864_INDIR_DDRB_DLL_DQS_SEL1 0xeec 2114 #define TW5864_INDIR_DDRB_DLL_CLK90_SEL 0xeed 2115 #define TW5864_INDIR_DDRB_DLL_TEST_SEL_AND_TAP_S 0xeee 2116 2117 #define TW5864_INDIR_RESET 0xef0 2118 #define TW5864_INDIR_RESET_VD BIT(7) 2119 #define TW5864_INDIR_RESET_DLL BIT(6) 2120 #define TW5864_INDIR_RESET_MUX_CORE BIT(5) 2121 2122 #define TW5864_INDIR_PV_VD_CK_POL 0xefd 2123 #define TW5864_INDIR_PV_VD_CK_POL_PV(channel) BIT(channel) 2124 #define TW5864_INDIR_PV_VD_CK_POL_VD(channel) BIT(channel + 4) 2125 2126 #define TW5864_INDIR_CLK0_SEL 0xefe 2127 #define TW5864_INDIR_CLK0_SEL_VD_SHIFT 0 2128 #define TW5864_INDIR_CLK0_SEL_VD_MASK 0x3 2129 #define TW5864_INDIR_CLK0_SEL_PV_SHIFT 2 2130 #define TW5864_INDIR_CLK0_SEL_PV_MASK (0x3 << 2) 2131 #define TW5864_INDIR_CLK0_SEL_PV2_SHIFT 4 2132 #define TW5864_INDIR_CLK0_SEL_PV2_MASK (0x3 << 4) 2133