1 CAMBIUM-PTP650-MIB DEFINITIONS ::= BEGIN 2 3 IMPORTS 4 MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, 5 Integer32, IpAddress, 6 enterprises 7 FROM SNMPv2-SMI 8 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP 9 FROM SNMPv2-CONF 10 DisplayString 11 FROM SNMPv2-TC 12 InetAddress, InetAddressType 13 FROM INET-ADDRESS-MIB; 14 15 cambium MODULE-IDENTITY 16 LAST-UPDATED "201502060443Z" 17 ORGANIZATION "Cambium Networks Ltd." 18 CONTACT-INFO 19 "Post: Simon Whitaker 20 Cambium Networks Ltd. 21 Unit B2, 22 Linhay Business Park, 23 Eastern Road, 24 Ashburton, 25 Devon. 26 TQ13 7UP 27 United Kingdom 28 Phone: +44 (0) 1364 655 500 29 Email: simon.whitaker@cambiumnetworks.com" 30 DESCRIPTION 31 "MIB for non-line-of-sight (NLOS) wireless ethernet bridge." 32 REVISION "201502060443Z" 33 DESCRIPTION 34 "PTP650-01-40: 35 Added Second Data Service attributes to support a second data path over 36 wireless link. 37 Added support for Cable Diagnostics. 38 Added IEEE 1588 Transparent Clock source port and Transparent Clock source 39 alarm attributes." 40 REVISION "201406181412Z" 41 DESCRIPTION 42 "PTP650-01-20: 43 Added TDM group and NIDU attributes to support the telecomms interfaces. 44 Added Router Protocols group to support Microwave Adaptive Bandwidth (MAB). 45 Added support for Out-Of-Band Remote Management, and for mute and enable 46 transmission. Renamed 'ethernet bridging' attributes to 'data bridging'. 47 Made more SyncE attributes writable." 48 REVISION "201402211503Z" 49 DESCRIPTION 50 "PTP650-01-10: 51 Added Synchronous Ethernet (SyncE) and IEEE 1588 Transparent Clock. 52 Support PTP650s. Clarified localPacketFiltering, regulatoryBand, 53 TDD Sync status & alarm. TX power max increased to 30dBm. 54 Modified the bit assignments of enabledDiagnosticAlarms to combine 55 the various status & warning bits for the main PSU, Aux & SFP ports 56 into a single portState bit." 57 REVISION "201308021028Z" 58 DESCRIPTION "PTP650-01-00: Initial revision." 59 ::= { enterprises 17713 } 60 61 -- Groups in cambium 62 ptp OBJECT IDENTIFIER ::= { cambium 1 } 63 ptmp OBJECT IDENTIFIER ::= { cambium 2 } 64 ptp650 OBJECT IDENTIFIER ::= { cambium 7 } 65 66 -- Groups in ptp650 67 dfs OBJECT IDENTIFIER ::= { ptp650 3 } 68 bridge OBJECT IDENTIFIER ::= { ptp650 4 } 69 configuration OBJECT IDENTIFIER ::= { ptp650 5 } 70 ethernet OBJECT IDENTIFIER ::= { ptp650 6 } 71 tDM OBJECT IDENTIFIER ::= { ptp650 7 } 72 license OBJECT IDENTIFIER ::= { ptp650 8 } 73 management OBJECT IDENTIFIER ::= { ptp650 9 } 74 phyControl OBJECT IDENTIFIER ::= { ptp650 10 } 75 phyStatus OBJECT IDENTIFIER ::= { ptp650 12 } 76 alarms OBJECT IDENTIFIER ::= { ptp650 13 } 77 smtp OBJECT IDENTIFIER ::= { ptp650 15 } 78 snmpControl OBJECT IDENTIFIER ::= { ptp650 16 } 79 sntp OBJECT IDENTIFIER ::= { ptp650 17 } 80 reset OBJECT IDENTIFIER ::= { ptp650 18 } 81 versions OBJECT IDENTIFIER ::= { ptp650 19 } 82 pubStats OBJECT IDENTIFIER ::= { ptp650 20 } 83 encryption OBJECT IDENTIFIER ::= { ptp650 22 } 84 tDDControl OBJECT IDENTIFIER ::= { ptp650 23 } 85 aAAControl OBJECT IDENTIFIER ::= { ptp650 25 } 86 syslogControl OBJECT IDENTIFIER ::= { ptp650 24 } 87 routerProtocols OBJECT IDENTIFIER ::= { ptp650 26 } 88 cableDiagnostics OBJECT IDENTIFIER ::= { ptp650 27 } 89 supplementary OBJECT IDENTIFIER ::= { ptp650 96 } 90 ptpGroups OBJECT IDENTIFIER ::= { ptp650 98 } 91 ptpTraps OBJECT IDENTIFIER ::= { ptp650 99 } 92 ptpTrapPrefix OBJECT IDENTIFIER ::= { ptpTraps 0 } 93 94 -- Compliance information 95 -- 96 ptpCompliance MODULE-COMPLIANCE 97 STATUS current 98 DESCRIPTION 99 "The compliance statement for the Cambium PTP MIB" 100 MODULE -- this module 101 MANDATORY-GROUPS { dfsGroup 102 , bridgeGroup 103 , configurationGroup 104 , ethernetGroup 105 , tDMGroup 106 , licenseGroup 107 , managementGroup 108 , phyControlGroup 109 , phyStatusGroup 110 , alarmsGroup 111 , smtpGroup 112 , snmpControlGroup 113 , sntpGroup 114 , resetGroup 115 , versionsGroup 116 , pubStatsGroup 117 , encryptionGroup 118 , tDDControlGroup 119 , aAAControlGroup 120 , syslogControlGroup 121 , routerProtocolsGroup 122 , cableDiagnosticsGroup 123 , supplementaryGroup 124 , notificationsGroup 125 } 126 ::= { ptp650 97 } 127 128 dfsGroup OBJECT-GROUP 129 OBJECTS { dfsTableNumber 130 , extendedSpectrumScanning 131 , dfsMeans 132 , dfsNineNinePointNinePercentiles 133 , dfsPeaks 134 } 135 STATUS current 136 DESCRIPTION "The dfs object group." 137 ::= { ptpGroups 3 } 138 139 bridgeGroup OBJECT-GROUP 140 OBJECTS { localPacketFiltering 141 } 142 STATUS current 143 DESCRIPTION "The bridge object group." 144 ::= { ptpGroups 4 } 145 146 configurationGroup OBJECT-GROUP 147 OBJECTS { iPv4Address 148 , subnetMask 149 , gatewayIPAddress 150 , targetMACAddress 151 , masterSlaveMode 152 , maximumTransmitPower 153 , antennaGain 154 , cableLoss 155 , eIRP 156 , channelBandwidth 157 , linkName 158 , siteName 159 , accessMethod 160 , groupID 161 , iPv6Address 162 , iPVersion 163 , iPv6AutoConfiguredLinkLocalAddress 164 , iPv6PrefixLength 165 , iPv6GatewayAddress 166 , remoteInternetAddressType 167 , remoteInternetAddress 168 , subbandLowestFrequency 169 , subbandHighestFrequency 170 , enableTransmission 171 } 172 STATUS current 173 DESCRIPTION "The configuration object group." 174 ::= { ptpGroups 5 } 175 176 ethernetGroup OBJECT-GROUP 177 OBJECTS { mainPSUPortAutoNegotiation 178 , mainPSUPortAutoNegAdvertisement 179 , mainPSUPortAutoMdix 180 , mainPSUPortStatus 181 , mainPSUPortSpeedAndDuplex 182 , dataPortWirelessDownAlert 183 , useVLANForManagementInterfaces 184 , vLANManagementPriority 185 , vLANManagementVID 186 , auxPortStatus 187 , auxPortSpeedAndDuplex 188 , ethernetPriorityTableNumber 189 , l2CPPriorityTableNumber 190 , iPDSCPPriorityTableNumber 191 , mPLSTCPriorityTableNumber 192 , managementPortWirelessDownAlert 193 , qOSPriorityScheme 194 , unknownNetworkPriorityQueueMapping 195 , dSCPManagementPriority 196 , dataBridgingStatus 197 , mainPSUPortAllocation 198 , auxPortAllocation 199 , sFPPortAllocation 200 , dataPortPauseFrames 201 , sFPPortAutoNegotiation 202 , sFPPortAutoNegAdvertisement 203 , sFPPortAutoMdix 204 , sFPPortStatus 205 , sFPPortSpeedAndDuplex 206 , auxPortPowerOverEthernetOutput 207 , auxPortPowerOverEthernetOutputStatus 208 , syncETracking 209 , syncEEquipmentClock 210 , mainPSUPortQLRxOverwrite 211 , mainPSUPortSSMTx 212 , sFPPortSSMTx 213 , auxPortSSMTx 214 , syncETrackingState 215 , mainPSUPortQLRx 216 , auxPortQLRx 217 , sFPPortQLRx 218 , mainPSUPortQLTx 219 , auxPortQLTx 220 , sFPPortQLTx 221 , mainPSUPortSyncEMasterSlaveStatus 222 , auxPortSyncEMasterSlaveStatus 223 , sFPPortSyncEMasterSlaveStatus 224 , mainPSUPortGigabitMasterSlaveStatus 225 , auxPortGigabitMasterSlaveStatus 226 , sFPPortGigabitMasterSlaveStatus 227 , transparentClock 228 , transparentClockVLAN 229 , transparentClockVID 230 , mainPSUPortAcceptedQLRx 231 , auxPortAcceptedQLRx 232 , sFPPortAcceptedQLRx 233 , mainPSUPortSyncERxStatus 234 , auxPortSyncERxStatus 235 , sFPPortSyncERxStatus 236 , nIDULanPortStatus 237 , nIDULanPortSpeedAndDuplex 238 , oOBPriorityQueueMapping 239 , nIDULanPortAutoNegotiation 240 , nIDULanPortAutoNegAdvertisement 241 , nIDULanPortAutoMdix 242 , nIDULanPortGigabitMasterSlaveStatus 243 , txMABFrames 244 , managementNetworkAccessEnabled 245 , secondDataPortPauseFrames 246 , secondDataBridgingStatus 247 , transparentClockPort 248 , ethernetPriorityQueueMapping 249 , l2CPPriorityQueueMapping 250 , iPDSCPPriorityQueueMapping 251 , mPLSTCPriorityQueueMapping 252 } 253 STATUS current 254 DESCRIPTION "The ethernet object group." 255 ::= { ptpGroups 6 } 256 257 tDMGroup OBJECT-GROUP 258 OBJECTS { tDMInterfaceControl 259 , tDMInterfaceStatus 260 , tDMEnabledChannels 261 , tdmTableNumber 262 , tDMConfigurationMismatch 263 , lowestTDMModulationMode 264 , tDMChannelStatus 265 , tDMChannelLineCode 266 , tDMChannelCableLength 267 , tDMChannelLoopback 268 } 269 STATUS current 270 DESCRIPTION "The tDM object group." 271 ::= { ptpGroups 7 } 272 273 licenseGroup OBJECT-GROUP 274 OBJECTS { regulatoryBand 275 , productVariant 276 , productName 277 , frequencyVariant 278 , sNMPv3Enable 279 , licenseVersion 280 , licenseUnitSerialNumber 281 , licenseIssueNumber 282 , licenseCountry 283 , licenseNumberOfRegulatoryBands 284 , licenseBandwidthCap 285 , licenseEncryption 286 , licenseSecurityLevel 287 , licenseGroupAccess 288 , licenseOOBManagementSupport 289 , licenseSFPPortSupport 290 , licenseAuxiliaryPortSupport 291 , licenseCapacity 292 , licenseMaxNumberOfTDMChannels 293 , licenseIEEE1588Support 294 , licenseSyncESupport 295 , licenseIPv6Support 296 , licenseMinimumFirmwareVersion 297 , licenseFullCapabilityTrialStatus 298 , licenseRemainingTrialPeriod 299 , licenseRemainingTrialPeriodAlarm 300 , capacityVariantMismatch 301 , licenseTDDSyncSupport 302 , licenseMaxLinkRange 303 , licenseTrialPeriod 304 , licenseRARSupport 305 , licenseRegulatoryBandsList 306 } 307 STATUS current 308 DESCRIPTION "The license object group." 309 ::= { ptpGroups 8 } 310 311 managementGroup OBJECT-GROUP 312 OBJECTS { targetRange 313 , rangingMode 314 , installStatus 315 , installArmState 316 , tFTPServerPortNumber 317 , tFTPSoftwareUpgradeFileName 318 , tFTPStartSoftwareUpgrade 319 , tFTPSoftwareUpgradeStatus 320 , tFTPSoftwareUpgradeStatusText 321 , tFTPSoftwareUpgradeStatusAdditionalText 322 , hTTPAccessEnabled 323 , telnetAccessEnabled 324 , hTTPPortNumber 325 , hTTPSPortNumber 326 , telnetPortNumber 327 , hTTPSAccessEnabled 328 , tFTPServerInternetAddressType 329 , tFTPServerInternetAddress 330 , lowestDataModulationMode 331 , lowestSecondDataModulationMode 332 } 333 STATUS current 334 DESCRIPTION "The management object group." 335 ::= { ptpGroups 9 } 336 337 phyControlGroup OBJECT-GROUP 338 OBJECTS { linkSymmetry 339 , userConfiguredMaxModulationMode 340 , linkModeOptimization 341 , txColorCode 342 , rxColorCode 343 , remoteMaximumTransmitPower 344 } 345 STATUS current 346 DESCRIPTION "The phyControl object group." 347 ::= { ptpGroups 10 } 348 349 phyStatusGroup OBJECT-GROUP 350 OBJECTS { linkLoss 351 , receivePower 352 , vectorError 353 , transmitPower 354 , receiveChannel 355 , transmitChannel 356 , receiveFreqMHz 357 , transmitFreqMHz 358 , signalStrengthRatio 359 , receiveFreqKHz 360 , transmitFreqKHz 361 , rawReceivePower 362 , range 363 , receiveModulationMode 364 , transmitModulationMode 365 , searchState 366 } 367 STATUS current 368 DESCRIPTION "The phyStatus object group." 369 ::= { ptpGroups 12 } 370 371 alarmsGroup OBJECT-GROUP 372 OBJECTS { unitOutOfCalibration 373 , incompatibleRegulatoryBands 374 , noWirelessChannelAvailable 375 , wirelessLinkDisabledWarning 376 , mainPSUPortDisabledWarning 377 , sFPError 378 , mainPSUPortConfigurationMismatch 379 , incompatibleMasterAndSlave 380 , tDDSynchronizationStatus 381 , auxPortDisabledWarning 382 , tDDSynchronizationAlarm 383 , linkModeOptimizationMismatch 384 , auxPortConfigurationMismatch 385 , secureModeAlarm 386 , dataBridgingStatusAlarm 387 , sFPPortDisabledWarning 388 , sFPPortConfigurationMismatch 389 , maxLinkRangeExceeded 390 , nIDULanPortDisabledWarning 391 , nIDULanPortConfigurationMismatch 392 , portAllocationMismatch 393 , secondDataBridgingStatusAlarm 394 , transparentClockSourcePortAlarm 395 } 396 STATUS current 397 DESCRIPTION "The alarms object group." 398 ::= { ptpGroups 13 } 399 400 smtpGroup OBJECT-GROUP 401 OBJECTS { sMTPEmailAlert 402 , sMTPServerPortNumber 403 , sMTPSourceEmailAddress 404 , sMTPDestinationEmailAddress 405 , sMTPEnabledMessages 406 , sMTPServerInternetAddressType 407 , sMTPServerInternetAddress 408 } 409 STATUS current 410 DESCRIPTION "The smtp object group." 411 ::= { ptpGroups 15 } 412 413 snmpControlGroup OBJECT-GROUP 414 OBJECTS { sNMPPortNumber 415 , sNMPCommunityString 416 , sNMPTrapTableNumber 417 , sNMPTrapVersion 418 , sNMPEnabledTraps 419 , enabledDiagnosticAlarms 420 , sNMPSendAllTrapsAtStartup 421 , sNMPTrapPortNumber 422 , sNMPTrapInternetAddressType 423 , sNMPTrapInternetAddress 424 , sNMPTrapReceiverEnabled 425 } 426 STATUS current 427 DESCRIPTION "The snmpControl object group." 428 ::= { ptpGroups 16 } 429 430 sntpGroup OBJECT-GROUP 431 OBJECTS { sNTPState 432 , sNTPPollInterval 433 , sNTPSync 434 , sNTPLastSync 435 , systemClock 436 , timeZone 437 , daylightSaving 438 , sNTPPrimaryServer 439 , sNTPPrimaryServerDeadTime 440 , sNTPServerRetries 441 , sNTPServerTimeout 442 , sNTPServerTableNumber 443 , sNTPServerPortNumber 444 , sNTPServerStatus 445 , sNTPServerInternetAddressType 446 , sNTPServerInternetAddress 447 } 448 STATUS current 449 DESCRIPTION "The sntp object group." 450 ::= { ptpGroups 17 } 451 452 resetGroup OBJECT-GROUP 453 OBJECTS { systemReset 454 } 455 STATUS current 456 DESCRIPTION "The reset object group." 457 ::= { ptpGroups 18 } 458 459 versionsGroup OBJECT-GROUP 460 OBJECTS { softwareVersion 461 , hardwareVersion 462 , secondarySoftwareVersion 463 , bootVersion 464 } 465 STATUS current 466 DESCRIPTION "The versions object group." 467 ::= { ptpGroups 19 } 468 469 pubStatsGroup OBJECT-GROUP 470 OBJECTS { receiveDataRate 471 , transmitDataRate 472 , aggregateDataRate 473 , wirelessLinkAvailability 474 , wirelessLinkStatus 475 , byteErrorRatio 476 , receiveModulationModeDetail 477 , dataBridgingAvailability 478 } 479 STATUS current 480 DESCRIPTION "The pubStats object group." 481 ::= { ptpGroups 20 } 482 483 encryptionGroup OBJECT-GROUP 484 OBJECTS { encryptionAlgorithm 485 } 486 STATUS current 487 DESCRIPTION "The encryption object group." 488 ::= { ptpGroups 22 } 489 490 tDDControlGroup OBJECT-GROUP 491 OBJECTS { tDDSynchronizationMode 492 } 493 STATUS current 494 DESCRIPTION "The tDDControl object group." 495 ::= { ptpGroups 23 } 496 497 aAAControlGroup OBJECT-GROUP 498 OBJECTS { userTableNumber 499 , userName 500 , userRole 501 , userEnabled 502 , userPassword 503 } 504 STATUS current 505 DESCRIPTION "The aAAControl object group." 506 ::= { ptpGroups 25 } 507 508 syslogControlGroup OBJECT-GROUP 509 OBJECTS { syslogClient 510 , syslogState 511 } 512 STATUS current 513 DESCRIPTION "The syslogControl object group." 514 ::= { ptpGroups 24 } 515 516 routerProtocolsGroup OBJECT-GROUP 517 OBJECTS { microwaveAdaptiveBandwidth 518 , mABNominalModulationMode 519 , mABTransmissionInterval 520 , mABHoldoffPeriod 521 , mABMaintenanceLevel 522 , useVLANForMABProtocol 523 , mABProtocolVID 524 , mABProtocolVLANPriority 525 , mABState 526 , mABNominalTransmitCapacity 527 , mABCurrentTransmitCapacity 528 } 529 STATUS current 530 DESCRIPTION "The routerProtocols object group." 531 ::= { ptpGroups 26 } 532 533 cableDiagnosticsGroup OBJECT-GROUP 534 OBJECTS { cableDiagnosticsPorts 535 , cableDiagnosticsControl 536 , cableDiagnosticsWarning 537 , cableDiagnosticsResultTableNumber 538 , cableDiagnosticsResultsDateTime 539 , cableDiagPair1Results 540 , cableDiagPair1Distance 541 , cableDiagPair2Results 542 , cableDiagPair2Distance 543 , cableDiagPair3Results 544 , cableDiagPair3Distance 545 , cableDiagPair4Results 546 , cableDiagPair4Distance 547 } 548 STATUS current 549 DESCRIPTION "The cableDiagnostics object group." 550 ::= { ptpGroups 27 } 551 552 supplementaryGroup OBJECT-GROUP 553 OBJECTS { longitude 554 , latitude 555 , altitude 556 } 557 STATUS current 558 DESCRIPTION "The supplementary object group." 559 ::= { ptpGroups 96 } 560 561 notificationsGroup NOTIFICATION-GROUP 562 NOTIFICATIONS { channelChangeTrap 563 , dfsImpulsiveInterferenceTrap 564 , mainPSUPortStatusTrap 565 , mainPSUPortDisabledWarningTrap 566 , mainPSUPortConfigurationMismatchTrap 567 , auxPortStatusTrap 568 , auxPortDisabledWarningTrap 569 , regulatoryBandTrap 570 , installStatusTrap 571 , installArmStateTrap 572 , unitOutOfCalibrationTrap 573 , auxPortPowerOverEthernetOutputStatusTrap 574 , incompatibleRegulatoryBandsTrap 575 , noWirelessChannelAvailableTrap 576 , wirelessLinkDisabledWarningTrap 577 , auxPortConfigurationMismatchTrap 578 , sFPErrorTrap 579 , sFPPortStatusTrap 580 , incompatibleMasterAndSlaveTrap 581 , sNTPSyncTrap 582 , tDDSynchronizationAlarmTrap 583 , sFPPortDisabledWarningTrap 584 , sFPPortConfigurationMismatchTrap 585 , linkModeOptimizationMismatchTrap 586 , tDMInterfaceStatusTrap 587 , tDMChannelStatusTrap 588 , tDMChannelLoopbackTrap 589 , nIDULanPortStatusTrap 590 , syslogStateTrap 591 , syslogLocalNearlyFullTrap 592 , syslogLocalWrappedTrap 593 , syslogClientTrap 594 , secureModeAlarmTrap 595 , dataBridgingStatusAlarmTrap 596 , licenseRemainingTrialPeriodAlarmTrap 597 , capacityVariantMismatchTrap 598 , maxLinkRangeExceededTrap 599 , tDMConfigurationMismatchTrap 600 , nIDULanPortDisabledWarningTrap 601 , nIDULanPortConfigurationMismatchTrap 602 , secondDataBridgingStatusAlarmTrap 603 , transparentClockSourcePortAlarmTrap 604 , portAllocationMismatchTrap 605 } 606 STATUS current 607 DESCRIPTION "The notifications group." 608 ::= { ptpGroups 99 } 609 610 611 DfsTableEntry ::= 612 SEQUENCE { dfsTableIndex INTEGER 613 , dfsMeans Integer32 614 , dfsNineNinePointNinePercentiles Integer32 615 , dfsPeaks Integer32 616 } 617 618 dfsTable OBJECT-TYPE 619 SYNTAX SEQUENCE OF DfsTableEntry 620 MAX-ACCESS not-accessible 621 STATUS current 622 DESCRIPTION 623 " A table storing a snapshot of various DFS measurements for each channel" 624 ::= { dfs 2 } 625 626 dfsTableEntry OBJECT-TYPE 627 SYNTAX DfsTableEntry 628 MAX-ACCESS not-accessible 629 STATUS current 630 DESCRIPTION 631 "Table DfsTable" 632 INDEX { dfsTableIndex } 633 ::= { dfsTable 1 } 634 635 EthernetPriorityTableEntry ::= 636 SEQUENCE { ethernetPriorityTableIndex INTEGER 637 , ethernetPriorityQueueMapping INTEGER 638 } 639 640 ethernetPriorityTable OBJECT-TYPE 641 SYNTAX SEQUENCE OF EthernetPriorityTableEntry 642 MAX-ACCESS not-accessible 643 STATUS current 644 DESCRIPTION 645 " A priority queue mapping table. This is a list of packet queues indexed by Ethernet priority." 646 ::= { ethernet 15 } 647 648 ethernetPriorityTableEntry OBJECT-TYPE 649 SYNTAX EthernetPriorityTableEntry 650 MAX-ACCESS not-accessible 651 STATUS current 652 DESCRIPTION 653 "Table EthernetPriorityTable" 654 INDEX { ethernetPriorityTableIndex } 655 ::= { ethernetPriorityTable 1 } 656 657 L2CPPriorityTableEntry ::= 658 SEQUENCE { l2CPPriorityTableIndex INTEGER 659 , l2CPPriorityQueueMapping INTEGER 660 } 661 662 l2CPPriorityTable OBJECT-TYPE 663 SYNTAX SEQUENCE OF L2CPPriorityTableEntry 664 MAX-ACCESS not-accessible 665 STATUS current 666 DESCRIPTION 667 " A priority queue mapping table. This is a list of packet queues indexed by L2CP priority." 668 ::= { ethernet 17 } 669 670 l2CPPriorityTableEntry OBJECT-TYPE 671 SYNTAX L2CPPriorityTableEntry 672 MAX-ACCESS not-accessible 673 STATUS current 674 DESCRIPTION 675 "Table L2CPPriorityTable" 676 INDEX { l2CPPriorityTableIndex } 677 ::= { l2CPPriorityTable 1 } 678 679 IPDSCPPriorityTableEntry ::= 680 SEQUENCE { iPDSCPPriorityTableIndex INTEGER 681 , iPDSCPPriorityQueueMapping INTEGER 682 } 683 684 iPDSCPPriorityTable OBJECT-TYPE 685 SYNTAX SEQUENCE OF IPDSCPPriorityTableEntry 686 MAX-ACCESS not-accessible 687 STATUS current 688 DESCRIPTION 689 " A priority queue mapping table. This is a list of packet queues indexed by L3 IP DSCP priority." 690 ::= { ethernet 19 } 691 692 iPDSCPPriorityTableEntry OBJECT-TYPE 693 SYNTAX IPDSCPPriorityTableEntry 694 MAX-ACCESS not-accessible 695 STATUS current 696 DESCRIPTION 697 "Table IPDSCPPriorityTable" 698 INDEX { iPDSCPPriorityTableIndex } 699 ::= { iPDSCPPriorityTable 1 } 700 701 MPLSTCPriorityTableEntry ::= 702 SEQUENCE { mPLSTCPriorityTableIndex INTEGER 703 , mPLSTCPriorityQueueMapping INTEGER 704 } 705 706 mPLSTCPriorityTable OBJECT-TYPE 707 SYNTAX SEQUENCE OF MPLSTCPriorityTableEntry 708 MAX-ACCESS not-accessible 709 STATUS current 710 DESCRIPTION 711 " A priority queue mapping table. This is a list of priority queues indexed by MPLS TC priority." 712 ::= { ethernet 21 } 713 714 mPLSTCPriorityTableEntry OBJECT-TYPE 715 SYNTAX MPLSTCPriorityTableEntry 716 MAX-ACCESS not-accessible 717 STATUS current 718 DESCRIPTION 719 "Table MPLSTCPriorityTable" 720 INDEX { mPLSTCPriorityTableIndex } 721 ::= { mPLSTCPriorityTable 1 } 722 723 TdmTableEntry ::= 724 SEQUENCE { tdmTableIndex INTEGER 725 , tDMChannelStatus INTEGER 726 , tDMChannelLineCode INTEGER 727 , tDMChannelCableLength INTEGER 728 , tDMChannelLoopback INTEGER 729 } 730 731 tdmTable OBJECT-TYPE 732 SYNTAX SEQUENCE OF TdmTableEntry 733 MAX-ACCESS not-accessible 734 STATUS current 735 DESCRIPTION 736 " A table storing a configuration and status for each TDM channel" 737 ::= { tDM 5 } 738 739 tdmTableEntry OBJECT-TYPE 740 SYNTAX TdmTableEntry 741 MAX-ACCESS not-accessible 742 STATUS current 743 DESCRIPTION 744 "Table TdmTable" 745 INDEX { tdmTableIndex } 746 ::= { tdmTable 1 } 747 748 LicenseRegulatoryBandsTableEntry ::= 749 SEQUENCE { licenseRegulatoryBandsTableIndex INTEGER 750 , licenseRegulatoryBandsList INTEGER 751 } 752 753 licenseRegulatoryBandsTable OBJECT-TYPE 754 SYNTAX SEQUENCE OF LicenseRegulatoryBandsTableEntry 755 MAX-ACCESS not-accessible 756 STATUS current 757 DESCRIPTION 758 "" 759 ::= { license 18 } 760 761 licenseRegulatoryBandsTableEntry OBJECT-TYPE 762 SYNTAX LicenseRegulatoryBandsTableEntry 763 MAX-ACCESS not-accessible 764 STATUS current 765 DESCRIPTION 766 "Table LicenseRegulatoryBandsTable" 767 INDEX { licenseRegulatoryBandsTableIndex } 768 ::= { licenseRegulatoryBandsTable 1 } 769 770 SNMPTrapTableEntry ::= 771 SEQUENCE { sNMPTrapTableIndex INTEGER 772 , sNMPTrapPortNumber INTEGER 773 , sNMPTrapInternetAddressType INTEGER 774 , sNMPTrapInternetAddress InetAddress 775 , sNMPTrapReceiverEnabled INTEGER 776 } 777 778 sNMPTrapTable OBJECT-TYPE 779 SYNTAX SEQUENCE OF SNMPTrapTableEntry 780 MAX-ACCESS not-accessible 781 STATUS current 782 DESCRIPTION 783 " SNMP trap configuration table." 784 ::= { snmpControl 4 } 785 786 sNMPTrapTableEntry OBJECT-TYPE 787 SYNTAX SNMPTrapTableEntry 788 MAX-ACCESS not-accessible 789 STATUS current 790 DESCRIPTION 791 "Table SNMPTrapTable" 792 INDEX { sNMPTrapTableIndex } 793 ::= { sNMPTrapTable 1 } 794 795 SNTPServerTableEntry ::= 796 SEQUENCE { sNTPServerTableIndex INTEGER 797 , sNTPServerPortNumber INTEGER 798 , sNTPServerStatus DisplayString 799 , sNTPServerInternetAddressType INTEGER 800 , sNTPServerInternetAddress InetAddress 801 } 802 803 sNTPServerTable OBJECT-TYPE 804 SYNTAX SEQUENCE OF SNTPServerTableEntry 805 MAX-ACCESS not-accessible 806 STATUS current 807 DESCRIPTION 808 "" 809 ::= { sntp 15 } 810 811 sNTPServerTableEntry OBJECT-TYPE 812 SYNTAX SNTPServerTableEntry 813 MAX-ACCESS not-accessible 814 STATUS current 815 DESCRIPTION 816 "Table SNTPServerTable" 817 INDEX { sNTPServerTableIndex } 818 ::= { sNTPServerTable 1 } 819 820 UserTableEntry ::= 821 SEQUENCE { userTableIndex INTEGER 822 , userName DisplayString 823 , userRole INTEGER 824 , userEnabled INTEGER 825 , userPassword DisplayString 826 } 827 828 userTable OBJECT-TYPE 829 SYNTAX SEQUENCE OF UserTableEntry 830 MAX-ACCESS not-accessible 831 STATUS current 832 DESCRIPTION 833 " The User Table Control group contains objects specifically for user account management." 834 ::= { aAAControl 2 } 835 836 userTableEntry OBJECT-TYPE 837 SYNTAX UserTableEntry 838 MAX-ACCESS not-accessible 839 STATUS current 840 DESCRIPTION 841 "Table UserTable" 842 INDEX { userTableIndex } 843 ::= { userTable 1 } 844 845 CableDiagnosticsResultTableEntry ::= 846 SEQUENCE { cableDiagnosticsResultTableIndex INTEGER 847 , cableDiagnosticsResultsDateTime Integer32 848 , cableDiagPair1Results INTEGER 849 , cableDiagPair1Distance Integer32 850 , cableDiagPair2Results INTEGER 851 , cableDiagPair2Distance Integer32 852 , cableDiagPair3Results INTEGER 853 , cableDiagPair3Distance Integer32 854 , cableDiagPair4Results INTEGER 855 , cableDiagPair4Distance Integer32 856 } 857 858 cableDiagnosticsResultTable OBJECT-TYPE 859 SYNTAX SEQUENCE OF CableDiagnosticsResultTableEntry 860 MAX-ACCESS not-accessible 861 STATUS current 862 DESCRIPTION 863 "" 864 ::= { cableDiagnostics 5 } 865 866 cableDiagnosticsResultTableEntry OBJECT-TYPE 867 SYNTAX CableDiagnosticsResultTableEntry 868 MAX-ACCESS not-accessible 869 STATUS current 870 DESCRIPTION 871 "Table CableDiagnosticsResultTable" 872 INDEX { cableDiagnosticsResultTableIndex } 873 ::= { cableDiagnosticsResultTable 1 } 874 875 -- Dfs group attribute definitions 876 -- 877 dfsTableNumber OBJECT-TYPE 878 SYNTAX INTEGER (1..63) 879 MAX-ACCESS read-only 880 STATUS current 881 DESCRIPTION 882 "Number of entries in the dfsTable" 883 ::= { dfs 1 } 884 885 extendedSpectrumScanning OBJECT-TYPE 886 SYNTAX INTEGER { 887 disabled(0), 888 enabled(1) 889 } 890 MAX-ACCESS read-only 891 STATUS current 892 DESCRIPTION 893 "Enables Extended Spectrum Scanning" 894 ::= { dfs 3 } 895 896 -- DfsTable group attribute definitions 897 -- 898 dfsTableIndex OBJECT-TYPE 899 SYNTAX INTEGER (1..63) 900 MAX-ACCESS not-accessible 901 STATUS current 902 DESCRIPTION 903 "used to index values in the dfsTable." 904 ::= { dfsTableEntry 1 } 905 906 dfsMeans OBJECT-TYPE 907 SYNTAX Integer32 908 MAX-ACCESS read-only 909 STATUS current 910 DESCRIPTION 911 "Snapshot of DFS means" 912 ::= { dfsTableEntry 2 } 913 914 dfsNineNinePointNinePercentiles OBJECT-TYPE 915 SYNTAX Integer32 916 MAX-ACCESS read-only 917 STATUS current 918 DESCRIPTION 919 "Snapshot of DFS 99.9 percentiles" 920 ::= { dfsTableEntry 3 } 921 922 dfsPeaks OBJECT-TYPE 923 SYNTAX Integer32 924 MAX-ACCESS read-only 925 STATUS current 926 DESCRIPTION 927 "Snapshot of DFS peaks" 928 ::= { dfsTableEntry 4 } 929 930 -- Bridge group attribute definitions 931 -- 932 localPacketFiltering OBJECT-TYPE 933 SYNTAX INTEGER { 934 disabled(0), 935 enabled(1) 936 } 937 MAX-ACCESS read-write 938 STATUS current 939 DESCRIPTION 940 "When Local Packet Filtering is Enabled, the unit keeps 941 track of the port (Main, SFP, Aux or Wireless) on which a 942 packet with a given MAC source address destined to the 943 management agent has been received. This MAC address to 944 port mapping is then used in order to route any response 945 from the management agent to the right port. When Local 946 Packet Filtering is Disabled, any Ethernet packet from 947 the management agent is sent to all ports." 948 ::= { bridge 1 } 949 950 -- Configuration group attribute definitions 951 -- 952 iPv4Address OBJECT-TYPE 953 SYNTAX IpAddress 954 MAX-ACCESS read-write 955 STATUS current 956 DESCRIPTION 957 "Internet protocol (IPv4) address. This address is used 958 by the family of Internet protocols to uniquely identify 959 the unit on a network." 960 ::= { configuration 1 } 961 962 subnetMask OBJECT-TYPE 963 SYNTAX IpAddress 964 MAX-ACCESS read-write 965 STATUS current 966 DESCRIPTION 967 "A subnet allows the flow of network traffic between 968 hosts to be segregated based on a network configuration. 969 By organizing hosts into logical groups, subnetting can 970 improve network security and performance." 971 ::= { configuration 2 } 972 973 gatewayIPAddress OBJECT-TYPE 974 SYNTAX IpAddress 975 MAX-ACCESS read-write 976 STATUS current 977 DESCRIPTION 978 "The IPv4 address of a device on the current network that 979 acts as an IPv4 network gateway. A gateway acts as an 980 entrance / exit to packets from / to other networks" 981 ::= { configuration 3 } 982 983 targetMACAddress OBJECT-TYPE 984 SYNTAX OCTET STRING (SIZE(6)) 985 MAX-ACCESS read-only 986 STATUS current 987 DESCRIPTION 988 "MAC address of the PTP wireless unit forming the other 989 end of the PTP link" 990 ::= { configuration 4 } 991 992 masterSlaveMode OBJECT-TYPE 993 SYNTAX INTEGER { 994 master(0), 995 slave(1) 996 } 997 MAX-ACCESS read-write 998 STATUS current 999 DESCRIPTION 1000 "The PTP wireless link operates using a master and slave 1001 relationship" 1002 ::= { configuration 5 } 1003 1004 maximumTransmitPower OBJECT-TYPE 1005 SYNTAX INTEGER (-15..30) 1006 MAX-ACCESS read-only 1007 STATUS current 1008 DESCRIPTION 1009 "Maximum transmit power the wireless unit is permitted to 1010 use when establishing and maintaining the wireless link. 1011 This may be reduced during installation" 1012 ::= { configuration 6 } 1013 1014 antennaGain OBJECT-TYPE 1015 SYNTAX INTEGER (130..610) 1016 MAX-ACCESS read-write 1017 STATUS current 1018 DESCRIPTION 1019 "Antenna Gain. Expressed in 10ths of dBi." 1020 ::= { configuration 7 } 1021 1022 cableLoss OBJECT-TYPE 1023 SYNTAX INTEGER (0..255) 1024 MAX-ACCESS read-write 1025 STATUS current 1026 DESCRIPTION 1027 "Loss in the cable between the ODU and the antenna. 1028 Expressed in 10ths of dB. NB: This attribute is ignored 1029 for variants with an integral antenna." 1030 ::= { configuration 8 } 1031 1032 eIRP OBJECT-TYPE 1033 SYNTAX Integer32 1034 MAX-ACCESS read-only 1035 STATUS current 1036 DESCRIPTION 1037 "Effective Isotropic Radiated Power (EIRP) describes the 1038 strength of the radio signal leaving the wireless unit. 1039 Expressed in 10ths of dBm" 1040 ::= { configuration 9 } 1041 1042 channelBandwidth OBJECT-TYPE 1043 SYNTAX INTEGER { 1044 bw30MHz(0), 1045 bw15MHz(1), 1046 bw10MHz(2), 1047 bw5MHz(3), 1048 bw20MHz(4), 1049 bw56MHz(5), 1050 bw50MHz(6), 1051 bw40MHz(7), 1052 bw45MHz(8) 1053 } 1054 MAX-ACCESS read-only 1055 STATUS current 1056 DESCRIPTION 1057 "This control sets the bandwidth of the transmit and 1058 receive radio channels" 1059 ::= { configuration 11 } 1060 1061 linkName OBJECT-TYPE 1062 SYNTAX DisplayString (SIZE(0..63)) 1063 MAX-ACCESS read-write 1064 STATUS current 1065 DESCRIPTION 1066 "Name of the PTP link allocated by the System 1067 Administrator. Used to establish a connection with the 1068 correct PTP wireless unit at the other end of the link. 1069 NOTE: The link name MUST be the same at both ends of the 1070 PTP link." 1071 ::= { configuration 14 } 1072 1073 siteName OBJECT-TYPE 1074 SYNTAX DisplayString (SIZE(0..63)) 1075 MAX-ACCESS read-write 1076 STATUS current 1077 DESCRIPTION 1078 "This field contains a user-provided description of the 1079 site name together with any additional notes" 1080 ::= { configuration 15 } 1081 1082 accessMethod OBJECT-TYPE 1083 SYNTAX INTEGER { 1084 linkAccess(0), 1085 linkNameAccess(1), 1086 groupAccess(2) 1087 } 1088 MAX-ACCESS read-only 1089 STATUS current 1090 DESCRIPTION 1091 "ODUs must be configured in pairs before a link can be 1092 established. The Access Method attribute determines how 1093 the paired ODUs will recognise each other. For the Link 1094 Access method, each ODU must be configured with Target 1095 MAC Address equal to the MAC Address of the other unit. 1096 For the Link Name Access method, both units must be 1097 configured with the same Link Name. For the Group Access 1098 method, both units must be configured with the same Group 1099 ID." 1100 ::= { configuration 16 } 1101 1102 groupID OBJECT-TYPE 1103 SYNTAX INTEGER (0..255) 1104 MAX-ACCESS read-write 1105 STATUS current 1106 DESCRIPTION 1107 "When Access Method is set to Group Access, the Group ID 1108 identifies all the units belonging to the same group" 1109 ::= { configuration 17 } 1110 1111 iPv6Address OBJECT-TYPE 1112 SYNTAX DisplayString (SIZE(0..39)) 1113 MAX-ACCESS read-write 1114 STATUS current 1115 DESCRIPTION 1116 "Internet protocol (IPv6) address. This address is used 1117 by the family of Internet protocols to uniquely identify 1118 the unit on a network." 1119 ::= { configuration 18 } 1120 1121 iPVersion OBJECT-TYPE 1122 SYNTAX INTEGER { 1123 iPv4(0), 1124 iPv6(1), 1125 dualIPv4andIPv6(2) 1126 } 1127 MAX-ACCESS read-write 1128 STATUS current 1129 DESCRIPTION 1130 "IP protocol selection. Choice of IPv4, IPv6 or Dual." 1131 ::= { configuration 20 } 1132 1133 iPv6AutoConfiguredLinkLocalAddress OBJECT-TYPE 1134 SYNTAX DisplayString (SIZE(0..39)) 1135 MAX-ACCESS read-only 1136 STATUS current 1137 DESCRIPTION 1138 "The auto configured link local IPv6 address" 1139 ::= { configuration 21 } 1140 1141 iPv6PrefixLength OBJECT-TYPE 1142 SYNTAX INTEGER (0..128) 1143 MAX-ACCESS read-write 1144 STATUS current 1145 DESCRIPTION 1146 "IPv6 prefix length" 1147 ::= { configuration 22 } 1148 1149 iPv6GatewayAddress OBJECT-TYPE 1150 SYNTAX DisplayString (SIZE(0..39)) 1151 MAX-ACCESS read-write 1152 STATUS current 1153 DESCRIPTION 1154 "The IPv6 address of a device on the current network that 1155 is currently acting as an IPv6 network gateway. A gateway 1156 acts as an entrance / exit to packets from / to other 1157 networks." 1158 ::= { configuration 23 } 1159 1160 remoteInternetAddressType OBJECT-TYPE 1161 SYNTAX INTEGER { 1162 unknown(0), 1163 ipv4(1), 1164 ipv6(2), 1165 ipv4z(3), 1166 ipv6z(4), 1167 unknown6(5), 1168 unknown7(6), 1169 unknown8(7), 1170 unknown9(8), 1171 unknown10(9), 1172 unknown11(10), 1173 unknown12(11), 1174 unknown13(12), 1175 unknown14(13), 1176 unknown15(14), 1177 unknown16(15), 1178 dns(16) 1179 } 1180 MAX-ACCESS read-only 1181 STATUS current 1182 DESCRIPTION 1183 "The type of Internet address specified by the associated 1184 remoteInternetAddressType." 1185 ::= { configuration 24 } 1186 1187 remoteInternetAddress OBJECT-TYPE 1188 SYNTAX InetAddress 1189 MAX-ACCESS read-only 1190 STATUS current 1191 DESCRIPTION 1192 "INET address used to identify the peer wireless unit" 1193 ::= { configuration 25 } 1194 1195 subbandLowestFrequency OBJECT-TYPE 1196 SYNTAX Integer32 1197 MAX-ACCESS read-only 1198 STATUS current 1199 DESCRIPTION 1200 "Lowest center frequency of the subset of channels." 1201 ::= { configuration 26 } 1202 1203 subbandHighestFrequency OBJECT-TYPE 1204 SYNTAX Integer32 1205 MAX-ACCESS read-only 1206 STATUS current 1207 DESCRIPTION 1208 "Highest center frequency of the subset of channels." 1209 ::= { configuration 27 } 1210 1211 enableTransmission OBJECT-TYPE 1212 SYNTAX INTEGER { 1213 enabled(0), 1214 muted(1) 1215 } 1216 MAX-ACCESS read-write 1217 STATUS current 1218 DESCRIPTION 1219 "Control for enabling/disabling the radio transmitter of 1220 the Master. Note: Use Web Properties to control this 1221 feature." 1222 ::= { configuration 28 } 1223 1224 -- Ethernet group attribute definitions 1225 -- 1226 mainPSUPortAutoNegotiation OBJECT-TYPE 1227 SYNTAX INTEGER { 1228 disabled(0), 1229 enabled(1) 1230 } 1231 MAX-ACCESS read-only 1232 STATUS current 1233 DESCRIPTION 1234 "This controls whether the local Ethernet interface 1235 configuration is automatically negotiated or forced. Do 1236 not use a forced setting together with auto negotiation 1237 at the Ethernet link partner. If you want to run your 1238 Ethernet link at a fixed speed and duplex then you would 1239 normally leave auto negotiation enabled and only enable 1240 the single Auto Neg Advertisement option that you want 1241 the link to run in - FORCING ETHERNET CONFIGURATION IS A 1242 LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE 1243 HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST 1244 ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET 1245 LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE 1246 LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED 1247 EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The 1248 new setting will only take effect after a system reboot." 1249 ::= { ethernet 1 } 1250 1251 mainPSUPortAutoNegAdvertisement OBJECT-TYPE 1252 SYNTAX BITS { 1253 negInvalid(2), 1254 neg10MbpsHalfDuplex(3), 1255 neg10MbpsFullDuplex(4), 1256 neg100MbpsHalfDuplex(5), 1257 neg100MbpsFullDuplex(6), 1258 neg1000MbpsFullDuplex(7) 1259 } 1260 MAX-ACCESS read-only 1261 STATUS current 1262 DESCRIPTION 1263 "This sets the different Ethernet configurations that 1264 will be advertised during auto negotiation. Note the new 1265 setting will only take effect after a system reboot. 1266 WARNING: Duplex mismatch may result if both ends of the 1267 Ethernet link do not have the same settings. Do not auto 1268 negotiation together with a fixed setting at the Ethernet 1269 link partner. WARNING: Make sure that you select 1270 option(s) that you know your connected equipment can 1271 cater for!" 1272 ::= { ethernet 2 } 1273 1274 mainPSUPortAutoMdix OBJECT-TYPE 1275 SYNTAX INTEGER { 1276 disabled(0), 1277 enabled(1) 1278 } 1279 MAX-ACCESS read-only 1280 STATUS current 1281 DESCRIPTION 1282 "This enables/disables the Auto MDI/MDIX capability. NB: 1283 The new setting will only take effect after a system 1284 reboot" 1285 ::= { ethernet 3 } 1286 1287 mainPSUPortStatus OBJECT-TYPE 1288 SYNTAX INTEGER { 1289 down(0), 1290 copperLinkUp(1), 1291 fiberLinkUp(2) 1292 } 1293 MAX-ACCESS read-only 1294 STATUS current 1295 DESCRIPTION 1296 "Current status of the Main PSU Ethernet link. NB: a 1297 change of state may generate an SNMP trap and/or SMTP 1298 email alert" 1299 ::= { ethernet 4 } 1300 1301 mainPSUPortSpeedAndDuplex OBJECT-TYPE 1302 SYNTAX INTEGER { 1303 speed1000MbpsFullDuplex(0), 1304 speed100MbpsFullDuplex(1), 1305 speed100MbpsHalfDuplex(2), 1306 speed10MbpsFullDuplex(3), 1307 speed10MbpsHalfDuplex(4), 1308 speedUnknown6(5) 1309 } 1310 MAX-ACCESS read-only 1311 STATUS current 1312 DESCRIPTION 1313 "The current speed and duplex of the Main PSU Ethernet 1314 link" 1315 ::= { ethernet 5 } 1316 1317 dataPortWirelessDownAlert OBJECT-TYPE 1318 SYNTAX INTEGER { 1319 disabled(0), 1320 enabled(1) 1321 } 1322 MAX-ACCESS read-write 1323 STATUS current 1324 DESCRIPTION 1325 "When enabled, this causes the Ethernet link to be 1326 dropped briefly when the wireless link drops. This is so 1327 that spanning tree algorithms can quickly detect that 1328 there is a problem." 1329 ::= { ethernet 6 } 1330 1331 useVLANForManagementInterfaces OBJECT-TYPE 1332 SYNTAX INTEGER { 1333 noVLANTagging(0), 1334 iEEE8021QTaggedCTagType8100(1), 1335 iEEE8021adTaggedSTagorBTagType88a8(2) 1336 } 1337 MAX-ACCESS read-write 1338 STATUS current 1339 DESCRIPTION 1340 "This controls whether the management interfaces 1341 (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new 1342 setting will only take effect after a system reboot" 1343 ::= { ethernet 7 } 1344 1345 vLANManagementPriority OBJECT-TYPE 1346 SYNTAX INTEGER { 1347 p0(0), 1348 p1(1), 1349 p2(2), 1350 p3(3), 1351 p4(4), 1352 p5(5), 1353 p6(6), 1354 p7(7) 1355 } 1356 MAX-ACCESS read-write 1357 STATUS current 1358 DESCRIPTION 1359 "This VLAN Priority (0-7) will be included in packets 1360 generated by the management interfaces" 1361 ::= { ethernet 8 } 1362 1363 vLANManagementVID OBJECT-TYPE 1364 SYNTAX INTEGER (0..4094) 1365 MAX-ACCESS read-write 1366 STATUS current 1367 DESCRIPTION 1368 "This VLAN VID (0-4094) will be included in packets 1369 generated by the management interfaces. Note the new 1370 setting will only take effect after a system reboot" 1371 ::= { ethernet 11 } 1372 1373 auxPortStatus OBJECT-TYPE 1374 SYNTAX INTEGER { 1375 down(0), 1376 copperLinkUp(1) 1377 } 1378 MAX-ACCESS read-only 1379 STATUS current 1380 DESCRIPTION 1381 "Current status of the Aux Ethernet link. NB: a change of 1382 state may generate an SNMP trap and/or SMTP email alert" 1383 ::= { ethernet 12 } 1384 1385 auxPortSpeedAndDuplex OBJECT-TYPE 1386 SYNTAX INTEGER { 1387 speed1000MbpsFullDuplex(0), 1388 speed100MbpsFullDuplex(1), 1389 speed100MbpsHalfDuplex(2), 1390 speed10MbpsFullDuplex(3), 1391 speed10MbpsHalfDuplex(4), 1392 speedUnknown6(5) 1393 } 1394 MAX-ACCESS read-only 1395 STATUS current 1396 DESCRIPTION 1397 "The current speed and duplex of the Aux Ethernet link" 1398 ::= { ethernet 13 } 1399 1400 ethernetPriorityTableNumber OBJECT-TYPE 1401 SYNTAX INTEGER (9) 1402 MAX-ACCESS read-only 1403 STATUS current 1404 DESCRIPTION 1405 "Number of entries in the vLANPriorityTable." 1406 ::= { ethernet 14 } 1407 1408 l2CPPriorityTableNumber OBJECT-TYPE 1409 SYNTAX INTEGER (5) 1410 MAX-ACCESS read-only 1411 STATUS current 1412 DESCRIPTION 1413 "Number of entries in the l2CPPriorityTable." 1414 ::= { ethernet 16 } 1415 1416 iPDSCPPriorityTableNumber OBJECT-TYPE 1417 SYNTAX INTEGER (64) 1418 MAX-ACCESS read-only 1419 STATUS current 1420 DESCRIPTION 1421 "Number of entries in the iPDSCPPriorityTable." 1422 ::= { ethernet 18 } 1423 1424 mPLSTCPriorityTableNumber OBJECT-TYPE 1425 SYNTAX INTEGER (8) 1426 MAX-ACCESS read-only 1427 STATUS current 1428 DESCRIPTION 1429 "Number of entries in the mPLSTCPriorityTable." 1430 ::= { ethernet 20 } 1431 1432 managementPortWirelessDownAlert OBJECT-TYPE 1433 SYNTAX INTEGER { 1434 disabled(0), 1435 enabled(1) 1436 } 1437 MAX-ACCESS read-write 1438 STATUS current 1439 DESCRIPTION 1440 "When enabled, this causes the management link to be 1441 dropped briefly when the wireless link drops. This is so 1442 that spanning tree algorithms can quickly detect that 1443 there is a problem." 1444 ::= { ethernet 23 } 1445 1446 qOSPriorityScheme OBJECT-TYPE 1447 SYNTAX INTEGER { 1448 ethernet(0), 1449 iPMPLS(1) 1450 } 1451 MAX-ACCESS read-write 1452 STATUS current 1453 DESCRIPTION 1454 "Selects classification based on fields in the Ethernet 1455 header (Layer 2) or in the Network header (Layer 3). The 1456 unit recognises two network layer protocols: IP and MPLS" 1457 ::= { ethernet 24 } 1458 1459 unknownNetworkPriorityQueueMapping OBJECT-TYPE 1460 SYNTAX INTEGER { 1461 q0(0), 1462 q1(1), 1463 q2(2), 1464 q3(3), 1465 q4(4), 1466 q5(5), 1467 q6(6), 1468 q7(7) 1469 } 1470 MAX-ACCESS read-write 1471 STATUS current 1472 DESCRIPTION 1473 "Configures the classification of unknown network 1474 protocols to an egress queue at the wireless port. 1475 Unknown means something other than IP and MPLS" 1476 ::= { ethernet 25 } 1477 1478 dSCPManagementPriority OBJECT-TYPE 1479 SYNTAX INTEGER (0..63) 1480 MAX-ACCESS read-only 1481 STATUS current 1482 DESCRIPTION 1483 "This Differentiated Services Code Point value will be 1484 inserted in the IP Header of all IP Datagrams transmitted 1485 by the management interfaces" 1486 ::= { ethernet 26 } 1487 1488 dataBridgingStatus OBJECT-TYPE 1489 SYNTAX INTEGER { 1490 disabled(0), 1491 enabled(1) 1492 } 1493 MAX-ACCESS read-only 1494 STATUS current 1495 DESCRIPTION 1496 "Current status of Ethernet Data traffic bridging over 1497 the wireless link" 1498 ::= { ethernet 27 } 1499 1500 mainPSUPortAllocation OBJECT-TYPE 1501 SYNTAX INTEGER { 1502 disabled(0), 1503 dataOnly(1), 1504 dataandInBandManagement(2), 1505 outofBandLocalManagement(3), 1506 outofBandRemoteManagement(4), 1507 secondDataOnly(5), 1508 secondDataandInBandManagement(6) 1509 } 1510 MAX-ACCESS read-only 1511 STATUS current 1512 DESCRIPTION 1513 "Indicates the service or services supported by the Main 1514 PSU Ethernet port" 1515 ::= { ethernet 28 } 1516 1517 auxPortAllocation OBJECT-TYPE 1518 SYNTAX INTEGER { 1519 disabled(0), 1520 dataOnly(1), 1521 dataandInBandManagement(2), 1522 outofBandLocalManagement(3), 1523 outofBandRemoteManagement(4), 1524 secondDataOnly(5), 1525 secondDataandInBandManagement(6) 1526 } 1527 MAX-ACCESS read-only 1528 STATUS current 1529 DESCRIPTION 1530 "Indicates the service or services supported by the Aux 1531 Ethernet port" 1532 ::= { ethernet 29 } 1533 1534 sFPPortAllocation OBJECT-TYPE 1535 SYNTAX INTEGER { 1536 disabled(0), 1537 dataOnly(1), 1538 dataandInBandManagement(2), 1539 outofBandLocalManagement(3), 1540 outofBandRemoteManagement(4), 1541 secondDataOnly(5), 1542 secondDataandInBandManagement(6) 1543 } 1544 MAX-ACCESS read-only 1545 STATUS current 1546 DESCRIPTION 1547 "Indicates the service or services supported by the SFP 1548 Ethernet port" 1549 ::= { ethernet 30 } 1550 1551 dataPortPauseFrames OBJECT-TYPE 1552 SYNTAX INTEGER { 1553 tunnel(0), 1554 discard(1) 1555 } 1556 MAX-ACCESS read-only 1557 STATUS current 1558 DESCRIPTION 1559 "Controls whether the bridge tunnels or discards Layer 2 1560 PAUSE frames arriving at the Data Port. Such frames are 1561 identified by the destination MAC Address being equal to 1562 01-80-C2-00-00-01" 1563 ::= { ethernet 31 } 1564 1565 sFPPortAutoNegotiation OBJECT-TYPE 1566 SYNTAX INTEGER { 1567 disabled(0), 1568 enabled(1) 1569 } 1570 MAX-ACCESS read-only 1571 STATUS current 1572 DESCRIPTION 1573 "This controls whether the local SFP Ethernet interface 1574 configuration is automatically negotiated or forced. Do 1575 not use a forced setting together with auto negotiation 1576 at the Ethernet link partner. If you want to run your 1577 Ethernet link at a fixed speed and duplex then you would 1578 normally leave auto negotiation enabled and only enable 1579 the single Auto Neg Advertisement option that you want 1580 the link to run in - FORCING ETHERNET CONFIGURATION IS A 1581 LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE 1582 HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST 1583 ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET 1584 LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE 1585 LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED 1586 EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The 1587 new setting will only take effect after a system reboot." 1588 ::= { ethernet 32 } 1589 1590 sFPPortAutoNegAdvertisement OBJECT-TYPE 1591 SYNTAX BITS { 1592 negInvalid(2), 1593 neg10MbpsHalfDuplex(3), 1594 neg10MbpsFullDuplex(4), 1595 neg100MbpsHalfDuplex(5), 1596 neg100MbpsFullDuplex(6), 1597 neg1000MbpsFullDuplex(7) 1598 } 1599 MAX-ACCESS read-only 1600 STATUS current 1601 DESCRIPTION 1602 "This sets the different SFP Ethernet configurations that 1603 will be advertised during auto negotiation. Note the new 1604 setting will only take effect after a system reboot. 1605 WARNING: Duplex mismatch may result if both ends of the 1606 Ethernet link do not have the same settings. Do not auto 1607 negotiation together with a fixed setting at the Ethernet 1608 link partner. WARNING: Make sure that you select 1609 option(s) that you know your connected equipment can 1610 cater for!" 1611 ::= { ethernet 33 } 1612 1613 sFPPortAutoMdix OBJECT-TYPE 1614 SYNTAX INTEGER { 1615 disabled(0), 1616 enabled(1) 1617 } 1618 MAX-ACCESS read-only 1619 STATUS current 1620 DESCRIPTION 1621 "This enables/disables the Auto MDI/MDIX capability. NB: 1622 The new setting will only take effect after a system 1623 reboot" 1624 ::= { ethernet 34 } 1625 1626 sFPPortStatus OBJECT-TYPE 1627 SYNTAX INTEGER { 1628 down(0), 1629 copperLinkUp(1), 1630 fiberLinkUp(2) 1631 } 1632 MAX-ACCESS read-only 1633 STATUS current 1634 DESCRIPTION 1635 "Current status of the SFP Ethernet link. NB: a change of 1636 state may generate an SNMP trap and/or SMTP email alert" 1637 ::= { ethernet 35 } 1638 1639 sFPPortSpeedAndDuplex OBJECT-TYPE 1640 SYNTAX INTEGER { 1641 speed1000MbpsFullDuplex(0), 1642 speed100MbpsFullDuplex(1), 1643 speed100MbpsHalfDuplex(2), 1644 speed10MbpsFullDuplex(3), 1645 speed10MbpsHalfDuplex(4), 1646 speedUnknown6(5) 1647 } 1648 MAX-ACCESS read-only 1649 STATUS current 1650 DESCRIPTION 1651 "The current speed and duplex of the SFP Ethernet link" 1652 ::= { ethernet 36 } 1653 1654 auxPortPowerOverEthernetOutput OBJECT-TYPE 1655 SYNTAX INTEGER { 1656 disabled(0), 1657 enabled(1) 1658 } 1659 MAX-ACCESS read-only 1660 STATUS current 1661 DESCRIPTION 1662 "The state of the Power Over Ethernet (PoE) output of the 1663 Aux port. Enabling PoE output may lead to system 1664 instability; please refer to the User Guide before 1665 enabling this control" 1666 ::= { ethernet 37 } 1667 1668 auxPortPowerOverEthernetOutputStatus OBJECT-TYPE 1669 SYNTAX INTEGER { 1670 poEOutputOn(0), 1671 poEOutputDisabled(1), 1672 poEOutputEnabledbutNotActiveErrororNoLoadPresent(2), 1673 poEOutputOverloadError(3), 1674 poEOutputOverTempError(4), 1675 poEOutputErrorDetected(5) 1676 } 1677 MAX-ACCESS read-only 1678 STATUS current 1679 DESCRIPTION 1680 "Current status of the Power Over Ethernet (PoE) output 1681 of the Aux port" 1682 ::= { ethernet 38 } 1683 1684 syncETracking OBJECT-TYPE 1685 SYNTAX INTEGER { 1686 disabled(0), 1687 enabled(1), 1688 internalTDMUseOnly(2) 1689 } 1690 MAX-ACCESS read-write 1691 STATUS current 1692 DESCRIPTION 1693 "Controls whether Synchronous Ethernet (SyncE) network 1694 synchronization is enabled." 1695 ::= { ethernet 39 } 1696 1697 syncEEquipmentClock OBJECT-TYPE 1698 SYNTAX INTEGER { 1699 eECOption1(0), 1700 eECOption2(1) 1701 } 1702 MAX-ACCESS read-write 1703 STATUS current 1704 DESCRIPTION 1705 "EEC-Option 1 applies to synchronous Ethernet equipments 1706 that are designed to interwork with networks optimized 1707 for the 2048-kbit/s hierarchy. Corresponds to ITU-T G.813 1708 Option 1; EEC-Option 2 applies to synchronous Ethernet 1709 equipments that are designed to interwork with networks 1710 optimized for the 1544-kbit/s hierarchy. Corresponds to 1711 Type IV clock from ITU-T G.812." 1712 ::= { ethernet 40 } 1713 1714 mainPSUPortQLRxOverwrite OBJECT-TYPE 1715 SYNTAX INTEGER { 1716 disabled(0), 1717 qLPRS(1), 1718 qLSTU(2), 1719 qLPRC(3), 1720 qLST2(4), 1721 qLSSUAQLTNC(5), 1722 qLSSUB(6), 1723 qLST3E(7), 1724 qLEEC2QLST3(8), 1725 qLEEC1QLSEC(9), 1726 qLSMC(10), 1727 qLPROV(11), 1728 qLDNUQLDUS(12) 1729 } 1730 MAX-ACCESS read-write 1731 STATUS current 1732 DESCRIPTION 1733 "Override for the Synchronous Ethernet (SyncE) received 1734 Quality Level (QL) on the main PSU port." 1735 ::= { ethernet 41 } 1736 1737 mainPSUPortSSMTx OBJECT-TYPE 1738 SYNTAX INTEGER { 1739 disabled(0), 1740 enabled(1) 1741 } 1742 MAX-ACCESS read-write 1743 STATUS current 1744 DESCRIPTION 1745 "Controls whether the Synchronous Ethernet (SyncE) 1746 Quality Level (QL) is transmitted on the Main PSU port" 1747 ::= { ethernet 42 } 1748 1749 sFPPortSSMTx OBJECT-TYPE 1750 SYNTAX INTEGER { 1751 disabled(0), 1752 enabled(1) 1753 } 1754 MAX-ACCESS read-write 1755 STATUS current 1756 DESCRIPTION 1757 "Controls whether the Synchronous Ethernet (SyncE) 1758 Quality Level (QL) is transmitted on the SFP port" 1759 ::= { ethernet 43 } 1760 1761 auxPortSSMTx OBJECT-TYPE 1762 SYNTAX INTEGER { 1763 disabled(0), 1764 enabled(1) 1765 } 1766 MAX-ACCESS read-write 1767 STATUS current 1768 DESCRIPTION 1769 "Controls whether the Synchronous Ethernet (SyncE) 1770 Quality Level (QL) is transmitted on the Aux port" 1771 ::= { ethernet 44 } 1772 1773 syncETrackingState OBJECT-TYPE 1774 SYNTAX INTEGER { 1775 disabled(0), 1776 acquiringWirelessLock(1), 1777 freeRunning(2), 1778 lockedLocalAcquiringHoldover(3), 1779 lockedLocalHoldoverAcquired(4), 1780 holdover(5), 1781 lockedRemoteAcquiringHoldover(6), 1782 lockedRemoteHoldoverAcquired(7) 1783 } 1784 MAX-ACCESS read-only 1785 STATUS current 1786 DESCRIPTION 1787 "The current state of Synchronous Ethernet (SyncE) 1788 network synchronization." 1789 ::= { ethernet 45 } 1790 1791 mainPSUPortQLRx OBJECT-TYPE 1792 SYNTAX INTEGER { 1793 none(0), 1794 qLPRS(1), 1795 qLSTU(2), 1796 qLPRC(3), 1797 qLST2(4), 1798 qLSSUAQLTNC(5), 1799 qLSSUB(6), 1800 qLST3E(7), 1801 qLEEC2QLST3(8), 1802 qLEEC1QLSEC(9), 1803 qLSMC(10), 1804 qLPROV(11), 1805 qLDNUQLDUS(12), 1806 qLFAILED(13) 1807 } 1808 MAX-ACCESS read-only 1809 STATUS current 1810 DESCRIPTION 1811 "The Synchronous Ethernet (SyncE) Quality Level (QL) 1812 currently being received on the main PSU port." 1813 ::= { ethernet 46 } 1814 1815 auxPortQLRx OBJECT-TYPE 1816 SYNTAX INTEGER { 1817 none(0), 1818 qLPRS(1), 1819 qLSTU(2), 1820 qLPRC(3), 1821 qLST2(4), 1822 qLSSUAQLTNC(5), 1823 qLSSUB(6), 1824 qLST3E(7), 1825 qLEEC2QLST3(8), 1826 qLEEC1QLSEC(9), 1827 qLSMC(10), 1828 qLPROV(11), 1829 qLDNUQLDUS(12), 1830 qLFAILED(13) 1831 } 1832 MAX-ACCESS read-only 1833 STATUS current 1834 DESCRIPTION 1835 "The Synchronous Ethernet (SyncE) Quality Level (QL) 1836 currently being received on the auxiliary port." 1837 ::= { ethernet 47 } 1838 1839 sFPPortQLRx OBJECT-TYPE 1840 SYNTAX INTEGER { 1841 none(0), 1842 qLPRS(1), 1843 qLSTU(2), 1844 qLPRC(3), 1845 qLST2(4), 1846 qLSSUAQLTNC(5), 1847 qLSSUB(6), 1848 qLST3E(7), 1849 qLEEC2QLST3(8), 1850 qLEEC1QLSEC(9), 1851 qLSMC(10), 1852 qLPROV(11), 1853 qLDNUQLDUS(12), 1854 qLFAILED(13) 1855 } 1856 MAX-ACCESS read-only 1857 STATUS current 1858 DESCRIPTION 1859 "The Synchronous Ethernet (SyncE) Quality Level (QL) 1860 currently being received on the SFP port." 1861 ::= { ethernet 48 } 1862 1863 mainPSUPortQLTx OBJECT-TYPE 1864 SYNTAX INTEGER { 1865 none(0), 1866 qLPRS(1), 1867 qLSTU(2), 1868 qLPRC(3), 1869 qLST2(4), 1870 qLSSUAQLTNC(5), 1871 qLSSUB(6), 1872 qLST3E(7), 1873 qLEEC2QLST3(8), 1874 qLEEC1QLSEC(9), 1875 qLSMC(10), 1876 qLPROV(11), 1877 qLDNUQLDUS(12) 1878 } 1879 MAX-ACCESS read-only 1880 STATUS current 1881 DESCRIPTION 1882 "The Synchronous Ethernet (SyncE) transmit Quality Level 1883 (QL) of the main PSU port." 1884 ::= { ethernet 49 } 1885 1886 auxPortQLTx OBJECT-TYPE 1887 SYNTAX INTEGER { 1888 none(0), 1889 qLPRS(1), 1890 qLSTU(2), 1891 qLPRC(3), 1892 qLST2(4), 1893 qLSSUAQLTNC(5), 1894 qLSSUB(6), 1895 qLST3E(7), 1896 qLEEC2QLST3(8), 1897 qLEEC1QLSEC(9), 1898 qLSMC(10), 1899 qLPROV(11), 1900 qLDNUQLDUS(12) 1901 } 1902 MAX-ACCESS read-only 1903 STATUS current 1904 DESCRIPTION 1905 "The Synchronous Ethernet (SyncE) transmit Quality Level 1906 (QL) of the auxiliary port." 1907 ::= { ethernet 50 } 1908 1909 sFPPortQLTx OBJECT-TYPE 1910 SYNTAX INTEGER { 1911 none(0), 1912 qLPRS(1), 1913 qLSTU(2), 1914 qLPRC(3), 1915 qLST2(4), 1916 qLSSUAQLTNC(5), 1917 qLSSUB(6), 1918 qLST3E(7), 1919 qLEEC2QLST3(8), 1920 qLEEC1QLSEC(9), 1921 qLSMC(10), 1922 qLPROV(11), 1923 qLDNUQLDUS(12) 1924 } 1925 MAX-ACCESS read-only 1926 STATUS current 1927 DESCRIPTION 1928 "The Synchronous Ethernet (SyncE) transmit Quality Level 1929 (QL) of the SFP port." 1930 ::= { ethernet 51 } 1931 1932 mainPSUPortSyncEMasterSlaveStatus OBJECT-TYPE 1933 SYNTAX INTEGER { 1934 master(0), 1935 slave(1) 1936 } 1937 MAX-ACCESS read-only 1938 STATUS current 1939 DESCRIPTION 1940 "The main PSU port Synchronous Ethernet (SyncE) 1941 Master/Slave status" 1942 ::= { ethernet 52 } 1943 1944 auxPortSyncEMasterSlaveStatus OBJECT-TYPE 1945 SYNTAX INTEGER { 1946 master(0), 1947 slave(1) 1948 } 1949 MAX-ACCESS read-only 1950 STATUS current 1951 DESCRIPTION 1952 "The auxiliary port Synchronous Ethernet (SyncE) 1953 Master/Slave status" 1954 ::= { ethernet 53 } 1955 1956 sFPPortSyncEMasterSlaveStatus OBJECT-TYPE 1957 SYNTAX INTEGER { 1958 master(0), 1959 slave(1) 1960 } 1961 MAX-ACCESS read-only 1962 STATUS current 1963 DESCRIPTION 1964 "The SFP port Synchronous Ethernet (SyncE) Master/Slave 1965 status" 1966 ::= { ethernet 54 } 1967 1968 mainPSUPortGigabitMasterSlaveStatus OBJECT-TYPE 1969 SYNTAX INTEGER { 1970 master(0), 1971 slave(1), 1972 notApplicable(2) 1973 } 1974 MAX-ACCESS read-only 1975 STATUS current 1976 DESCRIPTION 1977 "The main PSU port Gigabit Ethernet Master/Slave status" 1978 ::= { ethernet 55 } 1979 1980 auxPortGigabitMasterSlaveStatus OBJECT-TYPE 1981 SYNTAX INTEGER { 1982 master(0), 1983 slave(1), 1984 notApplicable(2) 1985 } 1986 MAX-ACCESS read-only 1987 STATUS current 1988 DESCRIPTION 1989 "The auxiliary port Gigabit Ethernet Master/Slave status" 1990 ::= { ethernet 56 } 1991 1992 sFPPortGigabitMasterSlaveStatus OBJECT-TYPE 1993 SYNTAX INTEGER { 1994 master(0), 1995 slave(1), 1996 notApplicable(2) 1997 } 1998 MAX-ACCESS read-only 1999 STATUS current 2000 DESCRIPTION 2001 "The SFP port Gigabit Ethernet Master/Slave status" 2002 ::= { ethernet 57 } 2003 2004 transparentClock OBJECT-TYPE 2005 SYNTAX INTEGER { 2006 disabled(0), 2007 enabled(1) 2008 } 2009 MAX-ACCESS read-write 2010 STATUS current 2011 DESCRIPTION 2012 "This control enables the Precision Time Protocol 2013 (IEEE-1588) Transparent Clock. Once enabled the unit will 2014 modify the correction field in PTP event messages to take 2015 account of the time these frames have been resident in 2016 this system. This will happen for all PTP frames at Layer 2017 2 & Layer 3 (IPv4 & IPv6) unless a transparent clock VLAN 2018 is enabled." 2019 ::= { ethernet 58 } 2020 2021 transparentClockVLAN OBJECT-TYPE 2022 SYNTAX INTEGER { 2023 all(0), 2024 sTagged(1), 2025 cTagged(2) 2026 } 2027 MAX-ACCESS read-write 2028 STATUS current 2029 DESCRIPTION 2030 "If All is selected then all PTP frames will have their 2031 correction fields modified with the residence time. If an 2032 S-TAG or C-TAG is selected, only frames with this VLAN 2033 tag and matching the VLAN ID in the Transparent Clock VID 2034 will have their correction fields modified." 2035 ::= { ethernet 59 } 2036 2037 transparentClockVID OBJECT-TYPE 2038 SYNTAX INTEGER (0..4094) 2039 MAX-ACCESS read-write 2040 STATUS current 2041 DESCRIPTION 2042 "The VLAN ID which frames must match if they are to be 2043 corrected. Only valid when an S-TAG or C-TAG has been 2044 selected." 2045 ::= { ethernet 60 } 2046 2047 mainPSUPortAcceptedQLRx OBJECT-TYPE 2048 SYNTAX INTEGER { 2049 none(0), 2050 qLPRS(1), 2051 qLSTU(2), 2052 qLPRC(3), 2053 qLST2(4), 2054 qLSSUAQLTNC(5), 2055 qLSSUB(6), 2056 qLST3E(7), 2057 qLEEC2QLST3(8), 2058 qLEEC1QLSEC(9), 2059 qLSMC(10), 2060 qLPROV(11), 2061 qLDNUQLDUS(12), 2062 qLFAILED(13) 2063 } 2064 MAX-ACCESS read-only 2065 STATUS current 2066 DESCRIPTION 2067 "The Synchronous Ethernet (SyncE) Quality Level (QL) 2068 currently accepted (validated) on the main PSU port." 2069 ::= { ethernet 61 } 2070 2071 auxPortAcceptedQLRx OBJECT-TYPE 2072 SYNTAX INTEGER { 2073 none(0), 2074 qLPRS(1), 2075 qLSTU(2), 2076 qLPRC(3), 2077 qLST2(4), 2078 qLSSUAQLTNC(5), 2079 qLSSUB(6), 2080 qLST3E(7), 2081 qLEEC2QLST3(8), 2082 qLEEC1QLSEC(9), 2083 qLSMC(10), 2084 qLPROV(11), 2085 qLDNUQLDUS(12), 2086 qLFAILED(13) 2087 } 2088 MAX-ACCESS read-only 2089 STATUS current 2090 DESCRIPTION 2091 "The Synchronous Ethernet (SyncE) Quality Level (QL) 2092 currently accepted (validated) on the auxiliary port." 2093 ::= { ethernet 62 } 2094 2095 sFPPortAcceptedQLRx OBJECT-TYPE 2096 SYNTAX INTEGER { 2097 none(0), 2098 qLPRS(1), 2099 qLSTU(2), 2100 qLPRC(3), 2101 qLST2(4), 2102 qLSSUAQLTNC(5), 2103 qLSSUB(6), 2104 qLST3E(7), 2105 qLEEC2QLST3(8), 2106 qLEEC1QLSEC(9), 2107 qLSMC(10), 2108 qLPROV(11), 2109 qLDNUQLDUS(12), 2110 qLFAILED(13) 2111 } 2112 MAX-ACCESS read-only 2113 STATUS current 2114 DESCRIPTION 2115 "The Synchronous Ethernet (SyncE) Quality Level (QL) 2116 currently accepted (validated) on the SFP port." 2117 ::= { ethernet 63 } 2118 2119 mainPSUPortSyncERxStatus OBJECT-TYPE 2120 SYNTAX INTEGER { 2121 good(0), 2122 waittoRestore(1), 2123 failed(2) 2124 } 2125 MAX-ACCESS read-only 2126 STATUS current 2127 DESCRIPTION 2128 "The Synchronous Ethernet (SyncE) Receive Status of the 2129 main PSU port" 2130 ::= { ethernet 64 } 2131 2132 auxPortSyncERxStatus OBJECT-TYPE 2133 SYNTAX INTEGER { 2134 good(0), 2135 waittoRestore(1), 2136 failed(2) 2137 } 2138 MAX-ACCESS read-only 2139 STATUS current 2140 DESCRIPTION 2141 "The Synchronous Ethernet (SyncE) Receive Status of the 2142 auxiliary port" 2143 ::= { ethernet 65 } 2144 2145 sFPPortSyncERxStatus OBJECT-TYPE 2146 SYNTAX INTEGER { 2147 good(0), 2148 waittoRestore(1), 2149 failed(2) 2150 } 2151 MAX-ACCESS read-only 2152 STATUS current 2153 DESCRIPTION 2154 "The Synchronous Ethernet (SyncE) Receive Status of the 2155 SFP port" 2156 ::= { ethernet 66 } 2157 2158 nIDULanPortStatus OBJECT-TYPE 2159 SYNTAX INTEGER { 2160 down(0), 2161 copperLinkUp(1), 2162 fiberLinkUp(2) 2163 } 2164 MAX-ACCESS read-only 2165 STATUS current 2166 DESCRIPTION 2167 "Current status of the NIDU LAN Ethernet link. NB: a 2168 change of state may generate an SNMP trap and/or SMTP 2169 email alert" 2170 ::= { ethernet 67 } 2171 2172 nIDULanPortSpeedAndDuplex OBJECT-TYPE 2173 SYNTAX INTEGER { 2174 speed1000MbpsFullDuplex(0), 2175 speed100MbpsFullDuplex(1), 2176 speed100MbpsHalfDuplex(2), 2177 speed10MbpsFullDuplex(3), 2178 speed10MbpsHalfDuplex(4), 2179 speedUnknown6(5) 2180 } 2181 MAX-ACCESS read-only 2182 STATUS current 2183 DESCRIPTION 2184 "The current speed and duplex of the Ethernet link to the 2185 NIDU LAN Port" 2186 ::= { ethernet 68 } 2187 2188 oOBPriorityQueueMapping OBJECT-TYPE 2189 SYNTAX INTEGER { 2190 q0(0), 2191 q1(1), 2192 q2(2), 2193 q3(3), 2194 q4(4), 2195 q5(5), 2196 q6(6), 2197 q7(7) 2198 } 2199 MAX-ACCESS read-write 2200 STATUS current 2201 DESCRIPTION 2202 "Configures the classification of traffic to an egress 2203 queue at the wireless port" 2204 ::= { ethernet 69 } 2205 2206 nIDULanPortAutoNegotiation OBJECT-TYPE 2207 SYNTAX INTEGER { 2208 disabled(0), 2209 enabled(1) 2210 } 2211 MAX-ACCESS read-only 2212 STATUS current 2213 DESCRIPTION 2214 "This controls whether the local Ethernet interface 2215 configuration is automatically negotiated or forced. Do 2216 not use a forced setting together with auto negotiation 2217 at the Ethernet link partner. If you want to run your 2218 Ethernet link at a fixed speed and duplex then you would 2219 normally leave auto negotiation enabled and only enable 2220 the single Auto Neg Advertisement option that you want 2221 the link to run in - FORCING ETHERNET CONFIGURATION IS A 2222 LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE 2223 HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST 2224 ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET 2225 LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE 2226 LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED 2227 EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The 2228 new setting will only take effect after a system reboot." 2229 ::= { ethernet 70 } 2230 2231 nIDULanPortAutoNegAdvertisement OBJECT-TYPE 2232 SYNTAX BITS { 2233 negInvalid(2), 2234 neg10MbpsHalfDuplex(3), 2235 neg10MbpsFullDuplex(4), 2236 neg100MbpsHalfDuplex(5), 2237 neg100MbpsFullDuplex(6), 2238 neg1000MbpsFullDuplex(7) 2239 } 2240 MAX-ACCESS read-only 2241 STATUS current 2242 DESCRIPTION 2243 "This sets the different Ethernet configurations that 2244 will be advertised during auto negotiation. Note the new 2245 setting will only take effect after a system reboot. 2246 WARNING: Duplex mismatch may result if both ends of the 2247 Ethernet link do not have the same settings. Do not auto 2248 negotiation together with a fixed setting at the Ethernet 2249 link partner. WARNING: Make sure that you select 2250 option(s) that you know your connected equipment can 2251 cater for!" 2252 ::= { ethernet 71 } 2253 2254 nIDULanPortAutoMdix OBJECT-TYPE 2255 SYNTAX INTEGER { 2256 disabled(0), 2257 enabled(1) 2258 } 2259 MAX-ACCESS read-only 2260 STATUS current 2261 DESCRIPTION 2262 "This enables/disables the Auto MDI/MDIX capability. NB: 2263 The new setting will only take effect after a system 2264 reboot" 2265 ::= { ethernet 72 } 2266 2267 nIDULanPortGigabitMasterSlaveStatus OBJECT-TYPE 2268 SYNTAX INTEGER { 2269 master(0), 2270 slave(1), 2271 notApplicable(2) 2272 } 2273 MAX-ACCESS read-only 2274 STATUS current 2275 DESCRIPTION 2276 "The NIDU LAN port Gigabit Ethernet Master/Slave status" 2277 ::= { ethernet 73 } 2278 2279 txMABFrames OBJECT-TYPE 2280 SYNTAX Integer32 2281 MAX-ACCESS read-only 2282 STATUS current 2283 DESCRIPTION 2284 "Number of MAB frames transmitted" 2285 ::= { ethernet 74 } 2286 2287 managementNetworkAccessEnabled OBJECT-TYPE 2288 SYNTAX INTEGER { 2289 no(0), 2290 yes(1) 2291 } 2292 MAX-ACCESS read-write 2293 STATUS current 2294 DESCRIPTION 2295 "When enabled the local Out-of-Band interface can be used 2296 to access the remote management network. If not enabled 2297 the local management agent can still be accessed from the 2298 remote management network and the local Out-of-Band 2299 interface" 2300 ::= { ethernet 75 } 2301 2302 secondDataPortPauseFrames OBJECT-TYPE 2303 SYNTAX INTEGER { 2304 tunnel(0), 2305 discard(1) 2306 } 2307 MAX-ACCESS read-only 2308 STATUS current 2309 DESCRIPTION 2310 "Controls whether the bridge tunnels or discards Layer 2 2311 PAUSE frames arriving at the Second Data Service Port. 2312 Such frames are identified by the destination MAC Address 2313 being equal to 01-80-C2-00-00-01" 2314 ::= { ethernet 76 } 2315 2316 secondDataBridgingStatus OBJECT-TYPE 2317 SYNTAX INTEGER { 2318 disabled(0), 2319 enabled(1) 2320 } 2321 MAX-ACCESS read-only 2322 STATUS current 2323 DESCRIPTION 2324 "Current status of bridging Second Data Service Ethernet 2325 traffic over the wireless link" 2326 ::= { ethernet 80 } 2327 2328 transparentClockPort OBJECT-TYPE 2329 SYNTAX INTEGER { 2330 mainPSU(0), 2331 aux(1), 2332 sFP(2) 2333 } 2334 MAX-ACCESS read-write 2335 STATUS current 2336 DESCRIPTION 2337 "IEEE 1588 Transparent Clock source" 2338 ::= { ethernet 81 } 2339 2340 -- EthernetPriorityTable group attribute definitions 2341 -- 2342 ethernetPriorityTableIndex OBJECT-TYPE 2343 SYNTAX INTEGER { 2344 p0(1), 2345 p1(2), 2346 p2(3), 2347 p3(4), 2348 p4(5), 2349 p5(6), 2350 p6(7), 2351 p7(8), 2352 untagged(9) 2353 } 2354 MAX-ACCESS not-accessible 2355 STATUS current 2356 DESCRIPTION 2357 "Ethernet priority flag, used to index values in the 2358 ethernetPriorityTable" 2359 ::= { ethernetPriorityTableEntry 1 } 2360 2361 ethernetPriorityQueueMapping OBJECT-TYPE 2362 SYNTAX INTEGER { 2363 q0(0), 2364 q1(1), 2365 q2(2), 2366 q3(3), 2367 q4(4), 2368 q5(5), 2369 q6(6), 2370 q7(7) 2371 } 2372 MAX-ACCESS read-write 2373 STATUS current 2374 DESCRIPTION 2375 "Configures the classification of this Ethernet priority 2376 (also known as IEEE 802.1p value) to an egress queue at 2377 the wireless port" 2378 ::= { ethernetPriorityTableEntry 2 } 2379 2380 -- L2CPPriorityTable group attribute definitions 2381 -- 2382 l2CPPriorityTableIndex OBJECT-TYPE 2383 SYNTAX INTEGER { 2384 bridge(1), 2385 mRP(2), 2386 cFM(3), 2387 rAPS(4), 2388 eAPS(5) 2389 } 2390 MAX-ACCESS not-accessible 2391 STATUS current 2392 DESCRIPTION 2393 "L2CP priority flag, used to index values in the 2394 l2CPPriorityTable" 2395 ::= { l2CPPriorityTableEntry 1 } 2396 2397 l2CPPriorityQueueMapping OBJECT-TYPE 2398 SYNTAX INTEGER { 2399 q0(0), 2400 q1(1), 2401 q2(2), 2402 q3(3), 2403 q4(4), 2404 q5(5), 2405 q6(6), 2406 q7(7) 2407 } 2408 MAX-ACCESS read-write 2409 STATUS current 2410 DESCRIPTION 2411 "Configures the classification of this layer two control 2412 protocol (L2CP) to an egress queue at the wireless port" 2413 ::= { l2CPPriorityTableEntry 2 } 2414 2415 -- IPDSCPPriorityTable group attribute definitions 2416 -- 2417 iPDSCPPriorityTableIndex OBJECT-TYPE 2418 SYNTAX INTEGER (1..64) 2419 MAX-ACCESS not-accessible 2420 STATUS current 2421 DESCRIPTION 2422 "IP DSCP priority flag, used to index values in the 2423 iPDSCPPriorityTable" 2424 ::= { iPDSCPPriorityTableEntry 1 } 2425 2426 iPDSCPPriorityQueueMapping OBJECT-TYPE 2427 SYNTAX INTEGER { 2428 q0(0), 2429 q1(1), 2430 q2(2), 2431 q3(3), 2432 q4(4), 2433 q5(5), 2434 q6(6), 2435 q7(7) 2436 } 2437 MAX-ACCESS read-write 2438 STATUS current 2439 DESCRIPTION 2440 "Configures the classification of this IP differentiated 2441 services code point (DSCP) value to an egress queue at 2442 the wireless port" 2443 ::= { iPDSCPPriorityTableEntry 2 } 2444 2445 -- MPLSTCPriorityTable group attribute definitions 2446 -- 2447 mPLSTCPriorityTableIndex OBJECT-TYPE 2448 SYNTAX INTEGER (1..8) 2449 MAX-ACCESS not-accessible 2450 STATUS current 2451 DESCRIPTION 2452 "MPLS TC priority flag, used to index values in the 2453 mPLSTCPriorityTable" 2454 ::= { mPLSTCPriorityTableEntry 1 } 2455 2456 mPLSTCPriorityQueueMapping OBJECT-TYPE 2457 SYNTAX INTEGER { 2458 q0(0), 2459 q1(1), 2460 q2(2), 2461 q3(3), 2462 q4(4), 2463 q5(5), 2464 q6(6), 2465 q7(7) 2466 } 2467 MAX-ACCESS read-write 2468 STATUS current 2469 DESCRIPTION 2470 "Configures the classification of this MPLS traffic class 2471 (the field formerly known as EXP) to an egress queue at 2472 the wireless port" 2473 ::= { mPLSTCPriorityTableEntry 2 } 2474 2475 -- TDM group attribute definitions 2476 -- 2477 tDMInterfaceControl OBJECT-TYPE 2478 SYNTAX INTEGER { 2479 none(0), 2480 e1(1), 2481 t1(2) 2482 } 2483 MAX-ACCESS read-only 2484 STATUS current 2485 DESCRIPTION 2486 "The line interface type. If this is set to 'None' then 2487 the TDM interfaces are disabled, and the TDM settings 2488 will be ignored." 2489 ::= { tDM 1 } 2490 2491 tDMInterfaceStatus OBJECT-TYPE 2492 SYNTAX INTEGER { 2493 ok(0), 2494 connectedNotConfigured(1), 2495 notConnected(2), 2496 nIDUdetectedonAUXport(3), 2497 error(4), 2498 codeDownloadInProgress(5) 2499 } 2500 MAX-ACCESS read-only 2501 STATUS current 2502 DESCRIPTION 2503 "@Current status of the connection to the TDM Box. A 2504 state of 'Up' on a green background indicates that the 2505 TDM Box is connected OK. When connecting a TDM Box only 2506 the Main Ethernet port should be used" 2507 ::= { tDM 2 } 2508 2509 tDMEnabledChannels OBJECT-TYPE 2510 SYNTAX INTEGER (0..8) 2511 MAX-ACCESS read-only 2512 STATUS current 2513 DESCRIPTION 2514 "The number of TDM channels enabled in the system" 2515 ::= { tDM 3 } 2516 2517 tdmTableNumber OBJECT-TYPE 2518 SYNTAX INTEGER (1..8) 2519 MAX-ACCESS read-only 2520 STATUS current 2521 DESCRIPTION 2522 "Number of entries in the TdmTable" 2523 ::= { tDM 4 } 2524 2525 tDMConfigurationMismatch OBJECT-TYPE 2526 SYNTAX INTEGER { 2527 ok(0), 2528 linetypemismatch(1), 2529 enabledchannelsmismatch(2), 2530 linetypeandenabledchannelsmismatch(3) 2531 } 2532 MAX-ACCESS read-only 2533 STATUS current 2534 DESCRIPTION 2535 "Current status of the configuration of the TDM Box. A 2536 state of 'Ok' on a green background indicates that the 2537 TDM Box configuration is matched OK with the remote end." 2538 ::= { tDM 6 } 2539 2540 lowestTDMModulationMode OBJECT-TYPE 2541 SYNTAX INTEGER { 2542 modAcquisition(0), 2543 modBpsk63percent(1), 2544 modQpsk63percentSingle(2), 2545 modTransient1(3), 2546 modQpsk87percentSingle(4), 2547 modTransient2(5), 2548 mod16qam63percentSingleA(6), 2549 modTransient3(7), 2550 mod16qam87percentSingle(8), 2551 modTransient4(9), 2552 mod64qam75percentSingle(10), 2553 modTransient5(11), 2554 mod64qam92percentSingle(12), 2555 modTransient6(13), 2556 mod256qam81percentSingle(14), 2557 mod16qam63percentSingleB(15), 2558 mod16qam63percentDual(16), 2559 modTransient7(17), 2560 mod16qam87percentDual(18), 2561 modTransient8(19), 2562 mod64qam75percentDual(20), 2563 modTransient9(21), 2564 mod64qam92percentDual(22), 2565 modTransient10(23), 2566 mod256qam81percentDual(24) 2567 } 2568 MAX-ACCESS read-only 2569 STATUS current 2570 DESCRIPTION 2571 "The lowest modulation mode at which tdm data will be 2572 sent. The effective lowest modulation mode is displayed 2573 in the TDM Configuration page" 2574 ::= { tDM 7 } 2575 2576 -- TdmTable group attribute definitions 2577 -- 2578 tdmTableIndex OBJECT-TYPE 2579 SYNTAX INTEGER (1..8) 2580 MAX-ACCESS not-accessible 2581 STATUS current 2582 DESCRIPTION 2583 "TDM Channel flag, used to index channels in the 2584 TdmTable" 2585 ::= { tdmTableEntry 1 } 2586 2587 tDMChannelStatus OBJECT-TYPE 2588 SYNTAX INTEGER { 2589 up(0), 2590 noSignalLocal(1), 2591 noSignalRemote(2), 2592 noSignalLocalandRemote(3), 2593 remoteTiming(4), 2594 noSignalLocalandRemoteTiming(5), 2595 disabled(6) 2596 } 2597 MAX-ACCESS read-only 2598 STATUS current 2599 DESCRIPTION 2600 "Current status of the TDM channels. A value of 0 2601 indicates that a TDM channel is established" 2602 ::= { tdmTableEntry 2 } 2603 2604 tDMChannelLineCode OBJECT-TYPE 2605 SYNTAX INTEGER { 2606 aMI(0), 2607 b8ZSorHDB3(1) 2608 } 2609 MAX-ACCESS read-only 2610 STATUS current 2611 DESCRIPTION 2612 "The line code setting of the TDM interfaces. This must 2613 match the setting of the device connected to an 2614 interface" 2615 ::= { tdmTableEntry 3 } 2616 2617 tDMChannelCableLength OBJECT-TYPE 2618 SYNTAX INTEGER { 2619 feet133(0), 2620 feet266(1), 2621 feet399(2), 2622 feet533(3), 2623 feet655(4) 2624 } 2625 MAX-ACCESS read-only 2626 STATUS current 2627 DESCRIPTION 2628 "The lengths of the cables connected to the TDM 2629 interfaces, measured in feet" 2630 ::= { tdmTableEntry 4 } 2631 2632 tDMChannelLoopback OBJECT-TYPE 2633 SYNTAX INTEGER { 2634 none(0), 2635 copper(1), 2636 wireless(2) 2637 } 2638 MAX-ACCESS read-only 2639 STATUS current 2640 DESCRIPTION 2641 "The loopback status of TDM channels. This is intended 2642 for installation testing and should be set to 'None' for 2643 normal operation. The wire connections to a unit can be 2644 tested by applying a 'Copper' loopback to the local unit. 2645 The wireless connection to the remote unit can be tested 2646 by applying a 'Wireless' loopback to the remote unit with 2647 no loopback on the local unit. NB: a change of state may 2648 generate an SNMP trap and/or SMTP email alert" 2649 ::= { tdmTableEntry 5 } 2650 2651 -- License group attribute definitions 2652 -- 2653 regulatoryBand OBJECT-TYPE 2654 SYNTAX INTEGER { 2655 regInvalid(0), 2656 reg158GHz(1), 2657 reg258GHz(2), 2658 reg358GHz(3), 2659 reg458GHz(4), 2660 reg558GHz(5), 2661 reg658GHz(6), 2662 reg754GHzUnrestrictedEIRPwithDFS(7), 2663 reg854GHzUnrestrictedEIRP(8), 2664 reg9(9), 2665 reg1058GHz(10), 2666 reg1158GHz(11), 2667 reg1254GHzFCCUNII2C(12), 2668 reg1354GHz(13), 2669 reg1449GHzPublicSafety(14), 2670 reg15(15), 2671 reg1659GHz(16), 2672 reg1759GHz(17), 2673 reg1849GHzPublicSafety(18), 2674 reg1958GHz(19), 2675 reg2054GHz(20), 2676 reg2154GHz(21), 2677 reg2258GHz(22), 2678 reg23(23), 2679 reg2458GHz(24), 2680 reg2558GHzETSI(25), 2681 reg2654GHzETSI(26), 2682 reg2758GHz(27), 2683 reg2858GHz(28), 2684 reg2958GHzUnrestrictedEIRPwithDFSandRTTT(29), 2685 reg3054GHz(30), 2686 reg3158GHz(31), 2687 reg3249GHzLicensed(32), 2688 reg3349GHzETSIBroadbandDisasterRelief(33), 2689 reg3458GHz(34), 2690 reg3558GHzUnrestrictedEIRP(35), 2691 reg3654GHz(36), 2692 reg3758GHz(37), 2693 reg3852GHzFCCUNII2A(38), 2694 reg3951GHzETSIBroadbandDisasterRelief(39), 2695 reg4054GHz(40), 2696 reg4154GHz(41), 2697 reg4254GHz(42), 2698 reg4354GHz(43), 2699 reg4458GHz(44), 2700 reg4558GHz(45), 2701 reg4658GHz(46), 2702 reg4758GHz(47), 2703 reg4858GHz(48), 2704 reg4958GHz(49), 2705 reg5058GHz(50), 2706 reg5158GHz(51), 2707 reg5258GHz(52), 2708 reg5358GHz(53), 2709 reg5458GHz(54), 2710 reg5558GHz(55), 2711 reg5654GHz(56), 2712 reg5754GHz(57), 2713 reg5858GHz(58), 2714 reg5958GHz(59), 2715 reg6058GHz(60), 2716 reg6149GHz(61), 2717 reg6252GHz(62), 2718 reg6352GHz(63), 2719 reg6451GHz(64), 2720 reg6551GHz(65), 2721 reg6651GHz(66), 2722 reg6752GHz(67), 2723 reg6852GHz(68), 2724 reg6952GHz(69), 2725 reg7052GHz(70), 2726 reg7152GHz(71), 2727 reg7252GHz(72), 2728 reg7352GHz(73), 2729 reg7452GHz(74), 2730 reg7552GHz(75), 2731 reg7652GHz(76), 2732 reg7752GHz(77), 2733 reg7849GHz(78), 2734 reg7954GHz(79), 2735 reg8049GHz(80), 2736 reg8147GHz(81), 2737 reg8247GHz(82), 2738 reg8352GHz(83), 2739 reg8451GHzFCCUNII1(84), 2740 reg8552GHzFCCUNII12A(85), 2741 reg8654GHzFCCUNII2A2C(86), 2742 reg8758GHz(87), 2743 reg8849GHz(88), 2744 reg8949GHz(89), 2745 reg9054GHzFCCUNII2CParabolicantenna(90), 2746 reg9152GHzFCCUNII2AParabolicantenna(91), 2747 reg9251GHzFCCUNII1Parabolicantenna(92), 2748 reg9349GHz(93), 2749 reg94(94), 2750 reg95(95), 2751 reg96(96), 2752 reg97(97), 2753 reg98(98), 2754 reg99(99), 2755 reg100(100), 2756 reg101(101), 2757 reg102(102), 2758 reg103(103), 2759 reg104(104), 2760 reg105(105), 2761 reg106(106), 2762 reg107(107), 2763 reg108(108), 2764 reg109(109), 2765 reg110(110), 2766 reg111(111), 2767 reg112(112), 2768 reg113(113), 2769 reg114(114), 2770 reg115(115), 2771 reg116(116), 2772 reg117(117), 2773 reg118(118), 2774 reg119(119), 2775 reg120(120), 2776 reg121(121), 2777 reg122(122), 2778 reg123(123), 2779 reg124(124), 2780 reg125(125), 2781 reg126(126), 2782 reg127(127), 2783 reg128(128), 2784 reg129(129), 2785 reg130(130), 2786 reg131(131), 2787 reg132(132), 2788 reg133(133), 2789 reg134(134), 2790 reg135(135), 2791 reg136(136), 2792 reg137(137), 2793 reg138(138), 2794 reg139(139), 2795 reg140(140), 2796 reg141(141), 2797 reg142(142), 2798 reg143(143), 2799 reg144(144), 2800 reg145(145), 2801 reg146(146), 2802 reg147(147), 2803 reg148(148), 2804 reg149(149), 2805 reg150(150), 2806 reg151(151), 2807 reg152(152), 2808 reg153(153), 2809 reg154(154), 2810 reg155(155), 2811 reg156(156), 2812 reg157(157), 2813 reg158(158), 2814 reg159(159), 2815 reg160(160), 2816 reg161(161), 2817 reg162(162), 2818 reg163(163), 2819 reg164(164), 2820 reg165(165), 2821 reg166(166), 2822 reg167(167), 2823 reg168(168), 2824 reg169(169), 2825 reg170(170), 2826 reg171(171), 2827 reg172(172), 2828 reg173(173), 2829 reg174(174), 2830 reg175(175), 2831 reg176(176), 2832 reg177(177), 2833 reg178(178), 2834 reg179(179), 2835 reg180(180), 2836 reg181(181), 2837 reg182(182), 2838 reg183(183), 2839 reg184(184), 2840 reg185(185), 2841 reg186(186), 2842 reg187(187), 2843 reg188(188), 2844 reg189(189), 2845 reg190(190), 2846 reg191(191), 2847 reg192(192), 2848 reg193(193), 2849 reg194(194), 2850 reg195(195), 2851 reg196(196), 2852 reg197(197), 2853 reg198(198), 2854 reg199(199), 2855 reg200(200), 2856 reg201(201), 2857 reg202(202), 2858 reg203(203), 2859 reg204(204), 2860 reg205(205), 2861 reg206(206), 2862 reg207(207), 2863 reg208(208), 2864 reg209(209), 2865 reg210(210), 2866 reg211(211), 2867 reg212(212), 2868 reg213(213), 2869 reg214(214), 2870 reg215(215), 2871 reg216(216), 2872 reg217(217), 2873 reg218(218), 2874 reg219(219), 2875 reg220(220), 2876 reg221(221), 2877 reg222(222), 2878 reg223(223), 2879 reg224(224), 2880 reg225(225), 2881 reg226(226), 2882 reg227(227), 2883 reg228(228), 2884 reg229(229), 2885 reg230(230), 2886 reg231(231), 2887 reg232(232), 2888 reg233(233), 2889 reg234(234), 2890 reg235(235), 2891 reg236(236), 2892 reg237(237), 2893 reg238(238), 2894 reg239(239), 2895 reg240(240), 2896 reg241(241), 2897 reg242(242), 2898 reg243(243), 2899 reg244(244), 2900 reg245(245), 2901 reg246(246), 2902 reg247(247), 2903 reg248(248), 2904 reg249(249), 2905 reg250(250), 2906 reg251(251), 2907 reg252(252), 2908 reg253(253), 2909 reg254(254), 2910 reg255(255) 2911 } 2912 MAX-ACCESS read-only 2913 STATUS current 2914 DESCRIPTION 2915 "The Regulatory Band prohibits the wireless unit from 2916 operating outside the regulated limits. An invalid 2917 Regulatory Band may be caused by a missing or incorrect 2918 License Key, a corrupt MAC Address or an attempt to 2919 configure a Regulatory Band not allowed by the License 2920 Key. NB: a change of state may generate an SNMP trap 2921 and/or SMTP email alert." 2922 ::= { license 1 } 2923 2924 productVariant OBJECT-TYPE 2925 SYNTAX INTEGER { 2926 pTPxx400Full(0), 2927 pTPxx400Deprecated1(1), 2928 pTPxx400Deprecated2(2), 2929 pTPxx400Lite(3), 2930 spare1(4), 2931 pTPxx300(5), 2932 spare2(6), 2933 spare3(7), 2934 pTPxx500FullDeprecated(8), 2935 pTPxx500LiteDeprecated(9), 2936 pTPxx500(10), 2937 pTPxx600Lite(11), 2938 pTPxx600Full(12), 2939 pTPxx650(13), 2940 spare6(14), 2941 pTP800(15) 2942 } 2943 MAX-ACCESS read-only 2944 STATUS current 2945 DESCRIPTION 2946 "The product variant" 2947 ::= { license 2 } 2948 2949 productName OBJECT-TYPE 2950 SYNTAX DisplayString (SIZE(0..63)) 2951 MAX-ACCESS read-only 2952 STATUS current 2953 DESCRIPTION 2954 "Name of the product variant" 2955 ::= { license 3 } 2956 2957 frequencyVariant OBJECT-TYPE 2958 SYNTAX INTEGER { 2959 freq5GHz(0), 2960 freq4GHz(1) 2961 } 2962 MAX-ACCESS read-only 2963 STATUS current 2964 DESCRIPTION 2965 "The hardware frequency variant" 2966 ::= { license 5 } 2967 2968 sNMPv3Enable OBJECT-TYPE 2969 SYNTAX INTEGER { 2970 disabled(0), 2971 enabled(1) 2972 } 2973 MAX-ACCESS read-only 2974 STATUS current 2975 DESCRIPTION 2976 "SNMPv3 availability control" 2977 ::= { license 9 } 2978 2979 licenseVersion OBJECT-TYPE 2980 SYNTAX INTEGER (1) 2981 MAX-ACCESS read-only 2982 STATUS current 2983 DESCRIPTION 2984 "The license key version." 2985 ::= { license 12 } 2986 2987 licenseUnitSerialNumber OBJECT-TYPE 2988 SYNTAX DisplayString (SIZE(0..11)) 2989 MAX-ACCESS read-only 2990 STATUS current 2991 DESCRIPTION 2992 "The unit serial number." 2993 ::= { license 13 } 2994 2995 licenseIssueNumber OBJECT-TYPE 2996 SYNTAX INTEGER (0..2147483647) 2997 MAX-ACCESS read-only 2998 STATUS current 2999 DESCRIPTION 3000 "The license key issue number for this unit." 3001 ::= { license 15 } 3002 3003 licenseCountry OBJECT-TYPE 3004 SYNTAX DisplayString (SIZE(0..103)) 3005 MAX-ACCESS read-only 3006 STATUS current 3007 DESCRIPTION 3008 "The country in which this unit is licensed to operate." 3009 ::= { license 16 } 3010 3011 licenseNumberOfRegulatoryBands OBJECT-TYPE 3012 SYNTAX INTEGER (0..32) 3013 MAX-ACCESS read-only 3014 STATUS current 3015 DESCRIPTION 3016 "The number of regulatory bands for which the unit is 3017 licensed to operate." 3018 ::= { license 17 } 3019 3020 licenseBandwidthCap OBJECT-TYPE 3021 SYNTAX INTEGER (0..2147483647) 3022 MAX-ACCESS read-only 3023 STATUS current 3024 DESCRIPTION 3025 "The wireless link bandwidth cap in MHz. Zero indicates 3026 no bandwidth cap." 3027 ::= { license 20 } 3028 3029 licenseEncryption OBJECT-TYPE 3030 SYNTAX INTEGER { 3031 none(0), 3032 aESRijndael(1), 3033 aES192bitRijndael(2), 3034 aES256bitRijndael(3) 3035 } 3036 MAX-ACCESS read-only 3037 STATUS current 3038 DESCRIPTION 3039 "The license key encryption algorithms available." 3040 ::= { license 21 } 3041 3042 licenseSecurityLevel OBJECT-TYPE 3043 SYNTAX INTEGER { 3044 normal(0), 3045 fIPS(1), 3046 uCAPL(2) 3047 } 3048 MAX-ACCESS read-only 3049 STATUS current 3050 DESCRIPTION 3051 "The license key security level." 3052 ::= { license 22 } 3053 3054 licenseGroupAccess OBJECT-TYPE 3055 SYNTAX INTEGER { 3056 disabled(0), 3057 enabled(1) 3058 } 3059 MAX-ACCESS read-only 3060 STATUS current 3061 DESCRIPTION 3062 "The license key group access setting." 3063 ::= { license 23 } 3064 3065 licenseOOBManagementSupport OBJECT-TYPE 3066 SYNTAX INTEGER { 3067 disabled(0), 3068 enabled(1) 3069 } 3070 MAX-ACCESS read-only 3071 STATUS current 3072 DESCRIPTION 3073 "The license key Out-Of-Band (OOB) support setting." 3074 ::= { license 24 } 3075 3076 licenseSFPPortSupport OBJECT-TYPE 3077 SYNTAX INTEGER { 3078 disabled(0), 3079 enabled(1) 3080 } 3081 MAX-ACCESS read-only 3082 STATUS current 3083 DESCRIPTION 3084 "The license key Ethernet SFP Port support setting." 3085 ::= { license 25 } 3086 3087 licenseAuxiliaryPortSupport OBJECT-TYPE 3088 SYNTAX INTEGER { 3089 disabled(0), 3090 enabled(1) 3091 } 3092 MAX-ACCESS read-only 3093 STATUS current 3094 DESCRIPTION 3095 "The license key Ethernet Auxiliary Port support 3096 setting." 3097 ::= { license 26 } 3098 3099 licenseCapacity OBJECT-TYPE 3100 SYNTAX INTEGER { 3101 full(0), 3102 mid(1), 3103 lite(2) 3104 } 3105 MAX-ACCESS read-only 3106 STATUS current 3107 DESCRIPTION 3108 "The license key capacity" 3109 ::= { license 27 } 3110 3111 licenseMaxNumberOfTDMChannels OBJECT-TYPE 3112 SYNTAX INTEGER (0..8) 3113 MAX-ACCESS read-only 3114 STATUS current 3115 DESCRIPTION 3116 "The license key maximum TDM channels setting. Zero 3117 indicates TDM not available." 3118 ::= { license 28 } 3119 3120 licenseIEEE1588Support OBJECT-TYPE 3121 SYNTAX INTEGER { 3122 disabled(0), 3123 enabled(1) 3124 } 3125 MAX-ACCESS read-only 3126 STATUS current 3127 DESCRIPTION 3128 "The license key IEEE-1588 support setting." 3129 ::= { license 29 } 3130 3131 licenseSyncESupport OBJECT-TYPE 3132 SYNTAX INTEGER { 3133 disabled(0), 3134 enabled(1) 3135 } 3136 MAX-ACCESS read-only 3137 STATUS current 3138 DESCRIPTION 3139 "The license key SyncE support setting." 3140 ::= { license 30 } 3141 3142 licenseIPv6Support OBJECT-TYPE 3143 SYNTAX INTEGER { 3144 disabled(0), 3145 enabled(1) 3146 } 3147 MAX-ACCESS read-only 3148 STATUS current 3149 DESCRIPTION 3150 "The license key IPv6 support setting." 3151 ::= { license 31 } 3152 3153 licenseMinimumFirmwareVersion OBJECT-TYPE 3154 SYNTAX DisplayString (SIZE(0..23)) 3155 MAX-ACCESS read-only 3156 STATUS current 3157 DESCRIPTION 3158 "The minimum firmware version required to support this 3159 license key." 3160 ::= { license 32 } 3161 3162 licenseFullCapabilityTrialStatus OBJECT-TYPE 3163 SYNTAX INTEGER { 3164 available(0), 3165 active(1), 3166 inactive(2), 3167 expired(3), 3168 unavailable(4) 3169 } 3170 MAX-ACCESS read-only 3171 STATUS current 3172 DESCRIPTION 3173 "The license key full capability trial period status." 3174 ::= { license 33 } 3175 3176 licenseRemainingTrialPeriod OBJECT-TYPE 3177 SYNTAX INTEGER (0..31536000) 3178 MAX-ACCESS read-only 3179 STATUS current 3180 DESCRIPTION 3181 "The remaining time for the license key full capability 3182 trial period." 3183 ::= { license 34 } 3184 3185 licenseRemainingTrialPeriodAlarm OBJECT-TYPE 3186 SYNTAX INTEGER { 3187 fullCapabilityTrialNotActiveOrMoreThan7DaysRemaining(0), 3188 fullCapabilityTrialExpiringInLessThan7Days(1), 3189 fullCapabilityTrialExpiringInLessThan6Days(2), 3190 fullCapabilityTrialExpiringInLessThan5Days(3), 3191 fullCapabilityTrialExpiringInLessThan4Days(4), 3192 fullCapabilityTrialExpiringInLessThan3Days(5), 3193 fullCapabilityTrialExpiringInLessThan2Days(6), 3194 fullCapabilityTrialExpiringInLessThan1Day(7), 3195 fullCapabilityTrialHasExpired(8) 3196 } 3197 MAX-ACCESS read-only 3198 STATUS current 3199 DESCRIPTION 3200 "If the full capability trial license period is about to 3201 expire then purchase a license upgrade from your 3202 reseller." 3203 ::= { license 35 } 3204 3205 capacityVariantMismatch OBJECT-TYPE 3206 SYNTAX INTEGER { 3207 noError(0), 3208 mismatchDetected(1) 3209 } 3210 MAX-ACCESS read-only 3211 STATUS current 3212 DESCRIPTION 3213 "The remote node of this link has a lower link capacity. 3214 Operating with a reduced effective link capacity." 3215 ::= { license 36 } 3216 3217 licenseTDDSyncSupport OBJECT-TYPE 3218 SYNTAX INTEGER { 3219 disabled(0), 3220 enabled(1) 3221 } 3222 MAX-ACCESS read-only 3223 STATUS current 3224 DESCRIPTION 3225 "The license key TDD Synchronization support setting." 3226 ::= { license 37 } 3227 3228 licenseMaxLinkRange OBJECT-TYPE 3229 SYNTAX INTEGER (0..1999) 3230 MAX-ACCESS read-only 3231 STATUS current 3232 DESCRIPTION 3233 "Maximum licensed range for the wireless link in tenths 3234 of km. A value of zero indicates that the maximum link 3235 range is not limited by the license." 3236 ::= { license 38 } 3237 3238 licenseTrialPeriod OBJECT-TYPE 3239 SYNTAX INTEGER (0..365) 3240 MAX-ACCESS read-only 3241 STATUS current 3242 DESCRIPTION 3243 "The license key maximum trial period, in days." 3244 ::= { license 39 } 3245 3246 licenseRARSupport OBJECT-TYPE 3247 SYNTAX INTEGER { 3248 disabled(0), 3249 mAB(1), 3250 dLEP(2), 3251 mABandDLEP(3) 3252 } 3253 MAX-ACCESS read-only 3254 STATUS current 3255 DESCRIPTION 3256 "The license key Radio Aware Routing support setting." 3257 ::= { license 40 } 3258 3259 -- LicenseRegulatoryBandsTable group attribute definitions 3260 -- 3261 licenseRegulatoryBandsTableIndex OBJECT-TYPE 3262 SYNTAX INTEGER (1..32) 3263 MAX-ACCESS not-accessible 3264 STATUS current 3265 DESCRIPTION 3266 "License regulatory bands, used to index the 3267 LicenseRegulatoryBandsTable." 3268 ::= { licenseRegulatoryBandsTableEntry 1 } 3269 3270 licenseRegulatoryBandsList OBJECT-TYPE 3271 SYNTAX INTEGER { 3272 regInvalid(0), 3273 reg158GHz(1), 3274 reg258GHz(2), 3275 reg358GHz(3), 3276 reg458GHz(4), 3277 reg558GHz(5), 3278 reg658GHz(6), 3279 reg754GHzUnrestrictedEIRPwithDFS(7), 3280 reg854GHzUnrestrictedEIRP(8), 3281 reg9(9), 3282 reg1058GHz(10), 3283 reg1158GHz(11), 3284 reg1254GHzFCCUNII2C(12), 3285 reg1354GHz(13), 3286 reg1449GHzPublicSafety(14), 3287 reg15(15), 3288 reg1659GHz(16), 3289 reg1759GHz(17), 3290 reg1849GHzPublicSafety(18), 3291 reg1958GHz(19), 3292 reg2054GHz(20), 3293 reg2154GHz(21), 3294 reg2258GHz(22), 3295 reg23(23), 3296 reg2458GHz(24), 3297 reg2558GHzETSI(25), 3298 reg2654GHzETSI(26), 3299 reg2758GHz(27), 3300 reg2858GHz(28), 3301 reg2958GHzUnrestrictedEIRPwithDFSandRTTT(29), 3302 reg3054GHz(30), 3303 reg3158GHz(31), 3304 reg3249GHzLicensed(32), 3305 reg3349GHzETSIBroadbandDisasterRelief(33), 3306 reg3458GHz(34), 3307 reg3558GHzUnrestrictedEIRP(35), 3308 reg3654GHz(36), 3309 reg3758GHz(37), 3310 reg3852GHzFCCUNII2A(38), 3311 reg3951GHzETSIBroadbandDisasterRelief(39), 3312 reg4054GHz(40), 3313 reg4154GHz(41), 3314 reg4254GHz(42), 3315 reg4354GHz(43), 3316 reg4458GHz(44), 3317 reg4558GHz(45), 3318 reg4658GHz(46), 3319 reg4758GHz(47), 3320 reg4858GHz(48), 3321 reg4958GHz(49), 3322 reg5058GHz(50), 3323 reg5158GHz(51), 3324 reg5258GHz(52), 3325 reg5358GHz(53), 3326 reg5458GHz(54), 3327 reg5558GHz(55), 3328 reg5654GHz(56), 3329 reg5754GHz(57), 3330 reg5858GHz(58), 3331 reg5958GHz(59), 3332 reg6058GHz(60), 3333 reg6149GHz(61), 3334 reg6252GHz(62), 3335 reg6352GHz(63), 3336 reg6451GHz(64), 3337 reg6551GHz(65), 3338 reg6651GHz(66), 3339 reg6752GHz(67), 3340 reg6852GHz(68), 3341 reg6952GHz(69), 3342 reg7052GHz(70), 3343 reg7152GHz(71), 3344 reg7252GHz(72), 3345 reg7352GHz(73), 3346 reg7452GHz(74), 3347 reg7552GHz(75), 3348 reg7652GHz(76), 3349 reg7752GHz(77), 3350 reg7849GHz(78), 3351 reg7954GHz(79), 3352 reg8049GHz(80), 3353 reg8147GHz(81), 3354 reg8247GHz(82), 3355 reg8352GHz(83), 3356 reg8451GHzFCCUNII1(84), 3357 reg8552GHzFCCUNII12A(85), 3358 reg8654GHzFCCUNII2A2C(86), 3359 reg8758GHz(87), 3360 reg8849GHz(88), 3361 reg8949GHz(89), 3362 reg9054GHzFCCUNII2CParabolicantenna(90), 3363 reg9152GHzFCCUNII2AParabolicantenna(91), 3364 reg9251GHzFCCUNII1Parabolicantenna(92), 3365 reg9349GHz(93), 3366 reg94(94), 3367 reg95(95), 3368 reg96(96), 3369 reg97(97), 3370 reg98(98), 3371 reg99(99), 3372 reg100(100), 3373 reg101(101), 3374 reg102(102), 3375 reg103(103), 3376 reg104(104), 3377 reg105(105), 3378 reg106(106), 3379 reg107(107), 3380 reg108(108), 3381 reg109(109), 3382 reg110(110), 3383 reg111(111), 3384 reg112(112), 3385 reg113(113), 3386 reg114(114), 3387 reg115(115), 3388 reg116(116), 3389 reg117(117), 3390 reg118(118), 3391 reg119(119), 3392 reg120(120), 3393 reg121(121), 3394 reg122(122), 3395 reg123(123), 3396 reg124(124), 3397 reg125(125), 3398 reg126(126), 3399 reg127(127), 3400 reg128(128), 3401 reg129(129), 3402 reg130(130), 3403 reg131(131), 3404 reg132(132), 3405 reg133(133), 3406 reg134(134), 3407 reg135(135), 3408 reg136(136), 3409 reg137(137), 3410 reg138(138), 3411 reg139(139), 3412 reg140(140), 3413 reg141(141), 3414 reg142(142), 3415 reg143(143), 3416 reg144(144), 3417 reg145(145), 3418 reg146(146), 3419 reg147(147), 3420 reg148(148), 3421 reg149(149), 3422 reg150(150), 3423 reg151(151), 3424 reg152(152), 3425 reg153(153), 3426 reg154(154), 3427 reg155(155), 3428 reg156(156), 3429 reg157(157), 3430 reg158(158), 3431 reg159(159), 3432 reg160(160), 3433 reg161(161), 3434 reg162(162), 3435 reg163(163), 3436 reg164(164), 3437 reg165(165), 3438 reg166(166), 3439 reg167(167), 3440 reg168(168), 3441 reg169(169), 3442 reg170(170), 3443 reg171(171), 3444 reg172(172), 3445 reg173(173), 3446 reg174(174), 3447 reg175(175), 3448 reg176(176), 3449 reg177(177), 3450 reg178(178), 3451 reg179(179), 3452 reg180(180), 3453 reg181(181), 3454 reg182(182), 3455 reg183(183), 3456 reg184(184), 3457 reg185(185), 3458 reg186(186), 3459 reg187(187), 3460 reg188(188), 3461 reg189(189), 3462 reg190(190), 3463 reg191(191), 3464 reg192(192), 3465 reg193(193), 3466 reg194(194), 3467 reg195(195), 3468 reg196(196), 3469 reg197(197), 3470 reg198(198), 3471 reg199(199), 3472 reg200(200), 3473 reg201(201), 3474 reg202(202), 3475 reg203(203), 3476 reg204(204), 3477 reg205(205), 3478 reg206(206), 3479 reg207(207), 3480 reg208(208), 3481 reg209(209), 3482 reg210(210), 3483 reg211(211), 3484 reg212(212), 3485 reg213(213), 3486 reg214(214), 3487 reg215(215), 3488 reg216(216), 3489 reg217(217), 3490 reg218(218), 3491 reg219(219), 3492 reg220(220), 3493 reg221(221), 3494 reg222(222), 3495 reg223(223), 3496 reg224(224), 3497 reg225(225), 3498 reg226(226), 3499 reg227(227), 3500 reg228(228), 3501 reg229(229), 3502 reg230(230), 3503 reg231(231), 3504 reg232(232), 3505 reg233(233), 3506 reg234(234), 3507 reg235(235), 3508 reg236(236), 3509 reg237(237), 3510 reg238(238), 3511 reg239(239), 3512 reg240(240), 3513 reg241(241), 3514 reg242(242), 3515 reg243(243), 3516 reg244(244), 3517 reg245(245), 3518 reg246(246), 3519 reg247(247), 3520 reg248(248), 3521 reg249(249), 3522 reg250(250), 3523 reg251(251), 3524 reg252(252), 3525 reg253(253), 3526 reg254(254), 3527 reg255(255) 3528 } 3529 MAX-ACCESS read-only 3530 STATUS current 3531 DESCRIPTION 3532 "The list of regulatory bands for which the unit is 3533 licensed to operate. A regulatory band prohibits the 3534 wireless unit from operating outside the regulated 3535 limits. An invalid regulatory band indicates a corrupted 3536 license key. NB: a change of state may generate an SNMP 3537 trap and/or SMTP email alert." 3538 ::= { licenseRegulatoryBandsTableEntry 2 } 3539 3540 -- Management group attribute definitions 3541 -- 3542 targetRange OBJECT-TYPE 3543 SYNTAX INTEGER (0..2000) 3544 MAX-ACCESS read-only 3545 STATUS current 3546 DESCRIPTION 3547 "Initial target range used in installation +/-1, 3548 expressed in tenths of a kilometer. When Auto-Ranging 3549 this must be set to 0" 3550 ::= { management 1 } 3551 3552 rangingMode OBJECT-TYPE 3553 SYNTAX INTEGER { 3554 auto0to40km(0), 3555 auto0to100km(1), 3556 auto0to200km(2), 3557 targetRange(3) 3558 } 3559 MAX-ACCESS read-only 3560 STATUS current 3561 DESCRIPTION 3562 "Type of ranging to use during installation, either 3563 Auto-Ranging or use a selectable Target Range" 3564 ::= { management 2 } 3565 3566 installStatus OBJECT-TYPE 3567 SYNTAX INTEGER { 3568 ok(0), 3569 wrongPeer(1) 3570 } 3571 MAX-ACCESS read-only 3572 STATUS current 3573 DESCRIPTION 3574 "A non-zero value indicates that signalling was received 3575 with the wrong MAC address or a mismatched link name. NB: 3576 It is very unusual to detect this, because units with 3577 mis-configured Target MAC Address will normally fail to 3578 establish a wireless link. However, rare circumstances 3579 may establish a partial wireless link and detect this 3580 situation. NB: A non-zero value on start-up, or a change 3581 of value during operation, may generate an SNMP trap 3582 and/or SMTP email alert" 3583 ::= { management 3 } 3584 3585 installArmState OBJECT-TYPE 3586 SYNTAX INTEGER { 3587 disarmed(0), 3588 armed(1) 3589 } 3590 MAX-ACCESS read-only 3591 STATUS current 3592 DESCRIPTION 3593 "Indicates if the unit is being installed. NB: a change 3594 of state may generate an SNMP trap and/or SMTP email 3595 alert" 3596 ::= { management 4 } 3597 3598 tFTPServerPortNumber OBJECT-TYPE 3599 SYNTAX INTEGER (0..65535) 3600 MAX-ACCESS read-write 3601 STATUS current 3602 DESCRIPTION 3603 "The port number of the TFTP Server from which the TFTP 3604 Software Upgrade File Name will be retrieved" 3605 ::= { management 6 } 3606 3607 tFTPSoftwareUpgradeFileName OBJECT-TYPE 3608 SYNTAX DisplayString (SIZE(0..127)) 3609 MAX-ACCESS read-write 3610 STATUS current 3611 DESCRIPTION 3612 "Filename of the Software Upgrade to be loaded from the 3613 TFTP Server" 3614 ::= { management 7 } 3615 3616 tFTPStartSoftwareUpgrade OBJECT-TYPE 3617 SYNTAX Integer32 3618 MAX-ACCESS read-write 3619 STATUS current 3620 DESCRIPTION 3621 "Write '1' to this attribute to start the TFTP software 3622 upgrade process. The attribute will be reset to 0 when 3623 the upgrade process has finished. Continuing with the 3624 software upgrade will cause spectrum management (DSO) 3625 channel metrics collection to stop. The wireless unit 3626 will no longer search for the optimal operational radio 3627 channel. The performance of this wireless link may 3628 deterioate over time. If operating in a regulatory band 3629 where RADAR detection is mandatory you must complete the 3630 software upgrade and reboot the unit. Channel metrics 3631 collection will only be restarted after the wireless unit 3632 has been rebooted" 3633 ::= { management 8 } 3634 3635 tFTPSoftwareUpgradeStatus OBJECT-TYPE 3636 SYNTAX INTEGER { 3637 idle(0), 3638 uploadinprogress(1), 3639 uploadsuccessfulprogrammingFLASH(2), 3640 upgradesuccessfulreboottorunthenewsoftwareimage(3), 3641 upgradefailed(4), 3642 upgradewarning(5) 3643 } 3644 MAX-ACCESS read-only 3645 STATUS current 3646 DESCRIPTION 3647 "The current status of the TFTP Software upgrade process" 3648 ::= { management 9 } 3649 3650 tFTPSoftwareUpgradeStatusText OBJECT-TYPE 3651 SYNTAX DisplayString (SIZE(0..127)) 3652 MAX-ACCESS read-only 3653 STATUS current 3654 DESCRIPTION 3655 "Descriptive text describing the status of the TFTP 3656 Software upgrade process, including any error details" 3657 ::= { management 10 } 3658 3659 tFTPSoftwareUpgradeStatusAdditionalText OBJECT-TYPE 3660 SYNTAX DisplayString (SIZE(0..127)) 3661 MAX-ACCESS read-only 3662 STATUS current 3663 DESCRIPTION 3664 "Any additional text describing the status of the TFTP 3665 Software upgrade process, including any error details" 3666 ::= { management 11 } 3667 3668 hTTPAccessEnabled OBJECT-TYPE 3669 SYNTAX INTEGER { 3670 no(0), 3671 yes(1) 3672 } 3673 MAX-ACCESS read-write 3674 STATUS current 3675 DESCRIPTION 3676 "This controls whether or not HTTP access is enabled, 3677 i.e. if this is disabled (0) then the unit will not 3678 respond to any requests on the HTTP port. Remote 3679 management via HTTPS is not affected by this setting. Any 3680 change in this setting will not take effect until the 3681 unit has been rebooted. (Factory default = Enabled)" 3682 ::= { management 12 } 3683 3684 telnetAccessEnabled OBJECT-TYPE 3685 SYNTAX INTEGER { 3686 no(0), 3687 yes(1) 3688 } 3689 MAX-ACCESS read-write 3690 STATUS current 3691 DESCRIPTION 3692 "This controls whether or not Telnet access is enabled, 3693 i.e. if this is disabled (0) then the unit will not 3694 respond to any requests on the TELNET port. Any change in 3695 this setting will not take effect until the unit has been 3696 rebooted. (Factory default = Disabled)" 3697 ::= { management 13 } 3698 3699 hTTPPortNumber OBJECT-TYPE 3700 SYNTAX INTEGER (0..65535) 3701 MAX-ACCESS read-write 3702 STATUS current 3703 DESCRIPTION 3704 "This controls the port number for HTTP access. A value 3705 of zero will use the default port number. Any change in 3706 this setting will not take effect until the unit has been 3707 rebooted. (Factory default = 80)" 3708 ::= { management 14 } 3709 3710 hTTPSPortNumber OBJECT-TYPE 3711 SYNTAX INTEGER (0..65535) 3712 MAX-ACCESS read-write 3713 STATUS current 3714 DESCRIPTION 3715 "This controls the port number for HTTPS access. A value 3716 of zero will use the default port number. Availability of 3717 HTTPS is controlled via the License Key. Any change in 3718 this setting will not take effect until the unit has been 3719 rebooted. (Factory default = 443)" 3720 ::= { management 15 } 3721 3722 telnetPortNumber OBJECT-TYPE 3723 SYNTAX INTEGER (0..65535) 3724 MAX-ACCESS read-write 3725 STATUS current 3726 DESCRIPTION 3727 "This controls the port number for TELNET access. A value 3728 of zero will use the default port number. Any change in 3729 this setting will not take effect until the unit has been 3730 rebooted. (Factory default = 23)" 3731 ::= { management 16 } 3732 3733 hTTPSAccessEnabled OBJECT-TYPE 3734 SYNTAX INTEGER { 3735 no(0), 3736 yes(1) 3737 } 3738 MAX-ACCESS read-write 3739 STATUS current 3740 DESCRIPTION 3741 "This controls whether or not HTTPS access is enabled, 3742 i.e. if this is disabled (0) then the unit will not 3743 respond to any requests on the HTTPS port. Remote 3744 management via HTTP is not affected by this setting. Any 3745 change in this setting will not take effect until the 3746 unit has been rebooted. (Factory default = Enabled)" 3747 ::= { management 17 } 3748 3749 tFTPServerInternetAddressType OBJECT-TYPE 3750 SYNTAX INTEGER { 3751 unknown(0), 3752 ipv4(1), 3753 ipv6(2), 3754 ipv4z(3), 3755 ipv6z(4), 3756 unknown6(5), 3757 unknown7(6), 3758 unknown8(7), 3759 unknown9(8), 3760 unknown10(9), 3761 unknown11(10), 3762 unknown12(11), 3763 unknown13(12), 3764 unknown14(13), 3765 unknown15(14), 3766 unknown16(15), 3767 dns(16) 3768 } 3769 MAX-ACCESS read-only 3770 STATUS current 3771 DESCRIPTION 3772 "The type of Internet address specified by the associated 3773 tFTPServerInternetAddress." 3774 ::= { management 18 } 3775 3776 tFTPServerInternetAddress OBJECT-TYPE 3777 SYNTAX InetAddress 3778 MAX-ACCESS read-write 3779 STATUS current 3780 DESCRIPTION 3781 "INET address of the TFTP Server from which the TFTP 3782 Software Upgrade File Name will be retrieved" 3783 ::= { management 19 } 3784 3785 lowestDataModulationMode OBJECT-TYPE 3786 SYNTAX INTEGER { 3787 modAcquisition(0), 3788 modBpsk63percent(1), 3789 modQpsk63percentSingle(2), 3790 modTransient1(3), 3791 modQpsk87percentSingle(4), 3792 modTransient2(5), 3793 mod16qam63percentSingleA(6), 3794 modTransient3(7), 3795 mod16qam87percentSingle(8), 3796 modTransient4(9), 3797 mod64qam75percentSingle(10), 3798 modTransient5(11), 3799 mod64qam92percentSingle(12), 3800 modTransient6(13), 3801 mod256qam81percentSingle(14), 3802 mod16qam63percentSingleB(15), 3803 mod16qam63percentDual(16), 3804 modTransient7(17), 3805 mod16qam87percentDual(18), 3806 modTransient8(19), 3807 mod64qam75percentDual(20), 3808 modTransient9(21), 3809 mod64qam92percentDual(22), 3810 modTransient10(23), 3811 mod256qam81percentDual(24) 3812 } 3813 MAX-ACCESS read-only 3814 STATUS current 3815 DESCRIPTION 3816 "The lowest modulation mode at which Ethernet Data 3817 traffic will be bridged over the wireless link" 3818 ::= { management 20 } 3819 3820 lowestSecondDataModulationMode OBJECT-TYPE 3821 SYNTAX INTEGER { 3822 modAcquisition(0), 3823 modBpsk63percent(1), 3824 modQpsk63percentSingle(2), 3825 modTransient1(3), 3826 modQpsk87percentSingle(4), 3827 modTransient2(5), 3828 mod16qam63percentSingleA(6), 3829 modTransient3(7), 3830 mod16qam87percentSingle(8), 3831 modTransient4(9), 3832 mod64qam75percentSingle(10), 3833 modTransient5(11), 3834 mod64qam92percentSingle(12), 3835 modTransient6(13), 3836 mod256qam81percentSingle(14), 3837 mod16qam63percentSingleB(15), 3838 mod16qam63percentDual(16), 3839 modTransient7(17), 3840 mod16qam87percentDual(18), 3841 modTransient8(19), 3842 mod64qam75percentDual(20), 3843 modTransient9(21), 3844 mod64qam92percentDual(22), 3845 modTransient10(23), 3846 mod256qam81percentDual(24) 3847 } 3848 MAX-ACCESS read-only 3849 STATUS current 3850 DESCRIPTION 3851 "The lowest modulation mode at which Second Data Service 3852 Ethernet traffic will be bridged over the wireless link" 3853 ::= { management 21 } 3854 3855 -- PhyControl group attribute definitions 3856 -- 3857 linkSymmetry OBJECT-TYPE 3858 SYNTAX INTEGER { 3859 symmetryAdaptive(0), 3860 symmetry2to1(1), 3861 symmetry1to1(2), 3862 symmetry1to2(3), 3863 symmetry3to1(4), 3864 symmetry1to3(5), 3865 symmetry5to1(6), 3866 symmetry1to5(7) 3867 } 3868 MAX-ACCESS read-only 3869 STATUS current 3870 DESCRIPTION 3871 "Provides configuration options for sharing the available 3872 wireless capacity between the transmit and receive 3873 directions. Fixed link symmetry is defined by a ratio of 3874 the burst duration for the transmit direction to the 3875 burst duration for the receive direction. Permitted 3876 settings are 5:1, 3:1, 2:1, 1:1, 1:2, 1:3, 1:5. The 1:1 3877 option provides fixed symmetric operation. The adaptive 3878 option selects transmit and receive burst durations 3879 automatically in response to the offered Ethernet traffic 3880 in each link direction. This attribute is valid only for 3881 a unit configured as a TDD Master" 3882 ::= { phyControl 1 } 3883 3884 userConfiguredMaxModulationMode OBJECT-TYPE 3885 SYNTAX INTEGER { 3886 modBpsk63percent(0), 3887 modQpsk63percent(1), 3888 modQpsk87percent(2), 3889 mod16qam63percent(3), 3890 mod16qam87percent(4), 3891 mod64qam75percent(5), 3892 mod64qam92percent(6), 3893 mod256qam81percent(7) 3894 } 3895 MAX-ACCESS read-write 3896 STATUS current 3897 DESCRIPTION 3898 "The maximum receive modulation mode controls the MAX 3899 mode used for adaptive modulation. NOTE: This attribute 3900 is automatically disabled when the installation agent is 3901 armed. To disarm the installation agent use the 3902 installation wizard" 3903 ::= { phyControl 2 } 3904 3905 linkModeOptimization OBJECT-TYPE 3906 SYNTAX INTEGER { 3907 iPTraffic(0), 3908 tDMTraffic(1) 3909 } 3910 MAX-ACCESS read-only 3911 STATUS current 3912 DESCRIPTION 3913 "Optimizes the wireless link behavior for the type of 3914 traffic to be carried. In 'IP Traffic' mode, the wireless 3915 link will minimize transmission errors by automatically 3916 adapting the modulation mode. In 'TDM Traffic' mode, the 3917 wireless link will minimize transmission latency and 3918 preserve throughput by maintaining a higher modulation 3919 mode in the presence of a limited number of errors. The 3920 'TDM Traffic' mode is recommended for E1/T1 applications 3921 and connectionless protocols." 3922 ::= { phyControl 3 } 3923 3924 txColorCode OBJECT-TYPE 3925 SYNTAX INTEGER { 3926 a(0), 3927 b(1), 3928 c(2), 3929 d(3), 3930 e(4) 3931 } 3932 MAX-ACCESS read-only 3933 STATUS current 3934 DESCRIPTION 3935 "Transmit Color Code. This attribute need only be 3936 considered when the unit is installed in a network of PTP 3937 units and where some of the units are operating on the 3938 same frequency. In this case, the value would normally be 3939 derived by a network planner. In all other cases, it is 3940 recommended that this attribute is left at the default 3941 value. NOTE: For the link to operate, the value of this 3942 parameter must in all cases match the value of the Rx 3943 Color Code parameter at the far end of the link." 3944 ::= { phyControl 4 } 3945 3946 rxColorCode OBJECT-TYPE 3947 SYNTAX INTEGER { 3948 a(0), 3949 b(1), 3950 c(2), 3951 d(3), 3952 e(4) 3953 } 3954 MAX-ACCESS read-only 3955 STATUS current 3956 DESCRIPTION 3957 "Receive Color Code. This attribute need only be 3958 considered when the unit is installed in a network of PTP 3959 units and where some of the units are operating on the 3960 same frequency. In this case, the value would normally be 3961 derived by a network planner. In all other cases, it is 3962 recommended that this attribute is left at the default 3963 value. NOTE: For the link to operate, the value of this 3964 parameter must in all cases match the value of the Tx 3965 Color Code parameter at the far end of the link." 3966 ::= { phyControl 5 } 3967 3968 remoteMaximumTransmitPower OBJECT-TYPE 3969 SYNTAX INTEGER (-15..30) 3970 MAX-ACCESS read-only 3971 STATUS current 3972 DESCRIPTION 3973 "Maximum transmit power the remote wireless unit is 3974 permitted to use when establishing and maintaining the 3975 wireless link" 3976 ::= { phyControl 6 } 3977 3978 -- PhyStatus group attribute definitions 3979 -- 3980 linkLoss OBJECT-TYPE 3981 SYNTAX INTEGER (-500..500) 3982 MAX-ACCESS read-only 3983 STATUS current 3984 DESCRIPTION 3985 "The wireless link loss expressed in tenths of a dB" 3986 ::= { phyStatus 1 } 3987 3988 receivePower OBJECT-TYPE 3989 SYNTAX Integer32 3990 MAX-ACCESS read-only 3991 STATUS current 3992 DESCRIPTION 3993 "Receive power expressed in tenths of a dBm" 3994 ::= { phyStatus 2 } 3995 3996 vectorError OBJECT-TYPE 3997 SYNTAX Integer32 3998 MAX-ACCESS read-only 3999 STATUS current 4000 DESCRIPTION 4001 "The vector error measurement compares the received 4002 signal's IQ modulation characteristics to an ideal signal 4003 to determine the composite error vector magnitude. The 4004 value represented by this attribute is the average vector 4005 error over the previous second expressed in tenths of a 4006 dB" 4007 ::= { phyStatus 3 } 4008 4009 transmitPower OBJECT-TYPE 4010 SYNTAX Integer32 4011 MAX-ACCESS read-only 4012 STATUS current 4013 DESCRIPTION 4014 "Transmit power expressed in tenths of a dBm" 4015 ::= { phyStatus 4 } 4016 4017 receiveChannel OBJECT-TYPE 4018 SYNTAX INTEGER (0..63) 4019 MAX-ACCESS read-only 4020 STATUS current 4021 DESCRIPTION 4022 "Current active receive channel" 4023 ::= { phyStatus 5 } 4024 4025 transmitChannel OBJECT-TYPE 4026 SYNTAX INTEGER (0..63) 4027 MAX-ACCESS read-only 4028 STATUS current 4029 DESCRIPTION 4030 "Current active transmit channel" 4031 ::= { phyStatus 6 } 4032 4033 receiveFreqMHz OBJECT-TYPE 4034 SYNTAX INTEGER (0..6050) 4035 MAX-ACCESS read-only 4036 STATUS current 4037 DESCRIPTION 4038 "Current receive frequency expressed in integer MHz" 4039 ::= { phyStatus 7 } 4040 4041 transmitFreqMHz OBJECT-TYPE 4042 SYNTAX INTEGER (0..6050) 4043 MAX-ACCESS read-only 4044 STATUS current 4045 DESCRIPTION 4046 "Current transmit frequency expressed in integer MHz" 4047 ::= { phyStatus 8 } 4048 4049 signalStrengthRatio OBJECT-TYPE 4050 SYNTAX Integer32 4051 MAX-ACCESS read-only 4052 STATUS current 4053 DESCRIPTION 4054 "Signal strength ratio (Vertical / Horizontal) : the 4055 number of dB larger the Vertical antenna input is than 4056 the Horizontal antenna input expressed in tenths of a dB" 4057 ::= { phyStatus 9 } 4058 4059 receiveFreqKHz OBJECT-TYPE 4060 SYNTAX INTEGER (0..6050000) 4061 MAX-ACCESS read-only 4062 STATUS current 4063 DESCRIPTION 4064 "Current receive frequency expressed as KHz" 4065 ::= { phyStatus 10 } 4066 4067 transmitFreqKHz OBJECT-TYPE 4068 SYNTAX INTEGER (0..6050000) 4069 MAX-ACCESS read-only 4070 STATUS current 4071 DESCRIPTION 4072 "Current transmit frequency expressed as KHz" 4073 ::= { phyStatus 11 } 4074 4075 rawReceivePower OBJECT-TYPE 4076 SYNTAX Integer32 4077 MAX-ACCESS read-only 4078 STATUS current 4079 DESCRIPTION 4080 "Raw receive power expressed in tenths of a dBm" 4081 ::= { phyStatus 12 } 4082 4083 range OBJECT-TYPE 4084 SYNTAX Integer32 4085 MAX-ACCESS read-only 4086 STATUS current 4087 DESCRIPTION 4088 "Distance between the two peer wireless units expressed 4089 in tenths of a kilometer" 4090 ::= { phyStatus 13 } 4091 4092 receiveModulationMode OBJECT-TYPE 4093 SYNTAX INTEGER { 4094 modAcquisition(0), 4095 modBpsk63percent(1), 4096 modQpsk63percentSingle(2), 4097 modTransient1(3), 4098 modQpsk87percentSingle(4), 4099 modTransient2(5), 4100 mod16qam63percentSingleA(6), 4101 modTransient3(7), 4102 mod16qam87percentSingle(8), 4103 modTransient4(9), 4104 mod64qam75percentSingle(10), 4105 modTransient5(11), 4106 mod64qam92percentSingle(12), 4107 modTransient6(13), 4108 mod256qam81percentSingle(14), 4109 mod16qam63percentSingleB(15), 4110 mod16qam63percentDual(16), 4111 modTransient7(17), 4112 mod16qam87percentDual(18), 4113 modTransient8(19), 4114 mod64qam75percentDual(20), 4115 modTransient9(21), 4116 mod64qam92percentDual(22), 4117 modTransient10(23), 4118 mod256qam81percentDual(24) 4119 } 4120 MAX-ACCESS read-only 4121 STATUS current 4122 DESCRIPTION 4123 "Current active receive modulation mode" 4124 ::= { phyStatus 14 } 4125 4126 transmitModulationMode OBJECT-TYPE 4127 SYNTAX INTEGER { 4128 modAcquisition(0), 4129 modBpsk63percent(1), 4130 modQpsk63percentSingle(2), 4131 modTransient1(3), 4132 modQpsk87percentSingle(4), 4133 modTransient2(5), 4134 mod16qam63percentSingleA(6), 4135 modTransient3(7), 4136 mod16qam87percentSingle(8), 4137 modTransient4(9), 4138 mod64qam75percentSingle(10), 4139 modTransient5(11), 4140 mod64qam92percentSingle(12), 4141 modTransient6(13), 4142 mod256qam81percentSingle(14), 4143 mod16qam63percentSingleB(15), 4144 mod16qam63percentDual(16), 4145 modTransient7(17), 4146 mod16qam87percentDual(18), 4147 modTransient8(19), 4148 mod64qam75percentDual(20), 4149 modTransient9(21), 4150 mod64qam92percentDual(22), 4151 modTransient10(23), 4152 mod256qam81percentDual(24) 4153 } 4154 MAX-ACCESS read-only 4155 STATUS current 4156 DESCRIPTION 4157 "Current active transmit modulation mode" 4158 ::= { phyStatus 15 } 4159 4160 searchState OBJECT-TYPE 4161 SYNTAX INTEGER { 4162 registering(0), 4163 searching(1), 4164 acquiring(2) 4165 } 4166 MAX-ACCESS read-only 4167 STATUS current 4168 DESCRIPTION 4169 "Search status of the wireless modem. 'Registering' means 4170 that the modem has locked to an OFDM signal, and the 4171 wireless link is up. 'Searching' means that no wireless 4172 signal has been detected. 'Acquiring' means that a 4173 wireless signal has been detected, but the modem has not 4174 locked to an OFDM signal." 4175 ::= { phyStatus 16 } 4176 4177 -- Alarms group attribute definitions 4178 -- 4179 unitOutOfCalibration OBJECT-TYPE 4180 SYNTAX INTEGER { 4181 calibrated(0), 4182 partialCalibration(1), 4183 invalidCalibration(2), 4184 bandwidthvariantunsupportedPAsShutdown(3), 4185 outOfCalibrationPAsShutdown(4) 4186 } 4187 MAX-ACCESS read-only 4188 STATUS current 4189 DESCRIPTION 4190 "The unit is out of calibration" 4191 ::= { alarms 1 } 4192 4193 incompatibleRegulatoryBands OBJECT-TYPE 4194 SYNTAX INTEGER { 4195 regOK(0), 4196 regIncompatibleLicenseKeys(1) 4197 } 4198 MAX-ACCESS read-only 4199 STATUS current 4200 DESCRIPTION 4201 "The master and slave units have incompatible regulatory 4202 bands. NB: Both units must have compatible license keys" 4203 ::= { alarms 4 } 4204 4205 noWirelessChannelAvailable OBJECT-TYPE 4206 SYNTAX INTEGER { 4207 ok(0), 4208 noWirelessChannelAvailable(1) 4209 } 4210 MAX-ACCESS read-only 4211 STATUS current 4212 DESCRIPTION 4213 "Spectrum Management was unable to locate a suitable 4214 wireless channel to operate on" 4215 ::= { alarms 5 } 4216 4217 wirelessLinkDisabledWarning OBJECT-TYPE 4218 SYNTAX INTEGER { 4219 ok(0), 4220 disabledBySNMPifAdminStatus(1) 4221 } 4222 MAX-ACCESS read-only 4223 STATUS current 4224 DESCRIPTION 4225 "The SNMP ifAdminStatus of the wireless interface has 4226 disabled wireless traffic" 4227 ::= { alarms 6 } 4228 4229 mainPSUPortDisabledWarning OBJECT-TYPE 4230 SYNTAX INTEGER { 4231 ok(0), 4232 disabledBySNMPifAdminStatus(1) 4233 } 4234 MAX-ACCESS read-only 4235 STATUS current 4236 DESCRIPTION 4237 "The SNMP ifAdminStatus of the interface has disabled 4238 Ethernet traffic" 4239 ::= { alarms 7 } 4240 4241 sFPError OBJECT-TYPE 4242 SYNTAX INTEGER { 4243 ok(0), 4244 installedSFPNotLicensed(1), 4245 fiberLinkNotEstablishedButLOSNotDetected(2), 4246 fiberLinkNotEstablishedAndLOSDetected(3), 4247 installedSFPNotSupported(4), 4248 sFPInitializationFailed(5) 4249 } 4250 MAX-ACCESS read-only 4251 STATUS current 4252 DESCRIPTION 4253 "If the SFP link is not OK, there are five possible 4254 causes: Either a SFP has been installed but the license 4255 key does not include SFP fiber support, a fiber link 4256 could not be established even though no LOS was detected 4257 (i.e. an optical carrier was detected, which could be due 4258 to a broken TX fiber, or because the link is disabled at 4259 the fiber link partner), a fiber link could not be 4260 established and LOS is detected (i.e. no optical carrier 4261 is detected), the installed SFP is not supported or the 4262 installed SFP failed to initialize correctly. NB: a 4263 change of status may generate an SNMP trap and/or SMTP 4264 email alert" 4265 ::= { alarms 8 } 4266 4267 mainPSUPortConfigurationMismatch OBJECT-TYPE 4268 SYNTAX INTEGER { 4269 noError(0), 4270 mismatchDetected(1) 4271 } 4272 MAX-ACCESS read-only 4273 STATUS current 4274 DESCRIPTION 4275 "The detection of Ethernet fragments (runt packets) when 4276 the link is in full duplex is an indication of an 4277 auto-negotiation or forced configuration mismatch" 4278 ::= { alarms 9 } 4279 4280 incompatibleMasterAndSlave OBJECT-TYPE 4281 SYNTAX INTEGER { 4282 ok(0), 4283 incompatibleProductVariants(1), 4284 differentSoftwareVersionsRunning(2) 4285 } 4286 MAX-ACCESS read-only 4287 STATUS current 4288 DESCRIPTION 4289 "A non-zero value indicates that the master and slave 4290 ends of a link are different hardware products, or have 4291 different software versions. NB: It is very unusual to 4292 detect this, because incompatible units will normally 4293 fail to establish a wireless link. However, some 4294 combinations may establish a partial wireless link and 4295 detect this situation. NB: A non-zero value may generate 4296 an SNMP trap and/or SMTP email alert" 4297 ::= { alarms 10 } 4298 4299 tDDSynchronizationStatus OBJECT-TYPE 4300 SYNTAX INTEGER { 4301 locked(0), 4302 holdover(1), 4303 holdoverNoGPSSyncIn(2), 4304 notSynchronized(3), 4305 notSynchronizedNoGPSSyncIn(4), 4306 pTPSYNCNotConnected(5), 4307 initialising(6), 4308 clusterTimingMaster(7), 4309 acquiringLock(8), 4310 inactive(9) 4311 } 4312 MAX-ACCESS read-only 4313 STATUS current 4314 DESCRIPTION 4315 "An alarm value (displayed in red) indicates that one of 4316 the following conditions has not been met (i) An external 4317 timing system is connected or internal timing has been 4318 configured. (ii) The timing system is providing a useable 4319 reference. (iii) The ODU is locked to this reference." 4320 ::= { alarms 11 } 4321 4322 auxPortDisabledWarning OBJECT-TYPE 4323 SYNTAX INTEGER { 4324 ok(0), 4325 disabledBySNMPifAdminStatus(1) 4326 } 4327 MAX-ACCESS read-only 4328 STATUS current 4329 DESCRIPTION 4330 "The SNMP ifAdminStatus of the interface has disabled 4331 Ethernet traffic" 4332 ::= { alarms 12 } 4333 4334 tDDSynchronizationAlarm OBJECT-TYPE 4335 SYNTAX INTEGER { 4336 ok(0), 4337 synchronizationLost(1), 4338 referenceSignalLost(2) 4339 } 4340 MAX-ACCESS read-only 4341 STATUS current 4342 DESCRIPTION 4343 "Not Synchronized indicates failure of the external 4344 timing system for a period greater than the holdover 4345 timer. TDD frame timing will have drifted, and this link 4346 may cause interference with other links in a synchronized 4347 network. Timing System Failure is an early warning, 4348 indicating that 80% of the holdover period has expired." 4349 ::= { alarms 13 } 4350 4351 linkModeOptimizationMismatch OBJECT-TYPE 4352 SYNTAX INTEGER { 4353 ok(0), 4354 linkModeOptimizationMismatch(1) 4355 } 4356 MAX-ACCESS read-only 4357 STATUS current 4358 DESCRIPTION 4359 "The remote node of this link has been configured with a 4360 different link mode optimization" 4361 ::= { alarms 14 } 4362 4363 auxPortConfigurationMismatch OBJECT-TYPE 4364 SYNTAX INTEGER { 4365 noError(0), 4366 mismatchDetected(1) 4367 } 4368 MAX-ACCESS read-only 4369 STATUS current 4370 DESCRIPTION 4371 "The detection of Ethernet fragments (runt packets) when 4372 the link is in full duplex is an indication of an 4373 auto-negotiation or forced configuration mismatch. This 4374 alarm is only raised if an Out-of-Band Management Mode 4375 has been configured." 4376 ::= { alarms 15 } 4377 4378 secureModeAlarm OBJECT-TYPE 4379 SYNTAX INTEGER { 4380 secureModeIsActive(0), 4381 secureModeIsNotConfigured(1), 4382 secureModeIsConfiguredButNotActive(2), 4383 secureModeIsNotSupported(3) 4384 } 4385 MAX-ACCESS read-only 4386 STATUS current 4387 DESCRIPTION 4388 "The secure mode (e.g. FIPS, UC-APL) state of the unit. 4389 The secure mode is not configured(1) state indicates that 4390 the unit is capable of secure mode operation, and one or 4391 more of the following security materials has not been 4392 configured: Key Of Keys, Private Key, Public Certificate, 4393 DRNG Entropy Status, Wireless Encryption Key. The secure 4394 mode mode is configured but not active(2) state indicates 4395 that the unit is capable of secure mode operation, and 4396 the security material has been configured, but the 4397 configuration of interfaces is not consistent with secure 4398 mode operation. The secure mode is not supported(3) state 4399 indicates that the unit is not capable of secure mode 4400 operation. The secure mode capability requires 4401 appropriate hardware compatibility, license key and 4402 software image." 4403 ::= { alarms 16 } 4404 4405 dataBridgingStatusAlarm OBJECT-TYPE 4406 SYNTAX INTEGER { 4407 bridgingEnabled(0), 4408 bridgingDisabled(1) 4409 } 4410 MAX-ACCESS read-only 4411 STATUS current 4412 DESCRIPTION 4413 "Ethernet Data traffic bridging is disabled because the 4414 wireless link is not operating at the configured Lowest 4415 Data Modulation Mode" 4416 ::= { alarms 17 } 4417 4418 sFPPortDisabledWarning OBJECT-TYPE 4419 SYNTAX INTEGER { 4420 ok(0), 4421 disabledBySNMPifAdminStatus(1) 4422 } 4423 MAX-ACCESS read-only 4424 STATUS current 4425 DESCRIPTION 4426 "The SNMP ifAdminStatus of the interface has disabled 4427 Ethernet traffic" 4428 ::= { alarms 18 } 4429 4430 sFPPortConfigurationMismatch OBJECT-TYPE 4431 SYNTAX INTEGER { 4432 noError(0), 4433 mismatchDetected(1) 4434 } 4435 MAX-ACCESS read-only 4436 STATUS current 4437 DESCRIPTION 4438 "The detection of Ethernet fragments (runt packets) when 4439 the link is in full duplex is an indication of an 4440 auto-negotiation or forced configuration mismatch. This 4441 alarm is only raised if an Out-of-Band Management Mode 4442 has been configured." 4443 ::= { alarms 19 } 4444 4445 maxLinkRangeExceeded OBJECT-TYPE 4446 SYNTAX INTEGER { 4447 maxLinkRangeOK(0), 4448 maxLinkRangeExceeded(1) 4449 } 4450 MAX-ACCESS read-only 4451 STATUS current 4452 DESCRIPTION 4453 "The measured link range is greater than the maximum 4454 allowed by the license key. The link will operate at a 4455 reduced capacity while this condition applies. This alarm 4456 is only raised if the license specifies a maximum link 4457 range and the trial license is not active." 4458 ::= { alarms 20 } 4459 4460 nIDULanPortDisabledWarning OBJECT-TYPE 4461 SYNTAX INTEGER { 4462 ok(0), 4463 disabledBySNMPifAdminStatus(1) 4464 } 4465 MAX-ACCESS read-only 4466 STATUS current 4467 DESCRIPTION 4468 "The SNMP ifAdminStatus of the interface has disabled 4469 Ethernet traffic" 4470 ::= { alarms 21 } 4471 4472 nIDULanPortConfigurationMismatch OBJECT-TYPE 4473 SYNTAX INTEGER { 4474 noError(0), 4475 mismatchDetected(1) 4476 } 4477 MAX-ACCESS read-only 4478 STATUS current 4479 DESCRIPTION 4480 "The detection of Ethernet fragments (runt packets) when 4481 the link is in full duplex is an indication of an 4482 auto-negotiation or forced configuration mismatch." 4483 ::= { alarms 22 } 4484 4485 portAllocationMismatch OBJECT-TYPE 4486 SYNTAX INTEGER { 4487 portAllocationOK(0), 4488 mismatchinSecondDataService(1), 4489 mismatchinOutofBandRemoteManagementService(2) 4490 } 4491 MAX-ACCESS read-only 4492 STATUS current 4493 DESCRIPTION 4494 "The local and remote ODUs have different services 4495 configured." 4496 ::= { alarms 23 } 4497 4498 secondDataBridgingStatusAlarm OBJECT-TYPE 4499 SYNTAX INTEGER { 4500 bridgingEnabled(0), 4501 bridgingDisabled(1) 4502 } 4503 MAX-ACCESS read-only 4504 STATUS current 4505 DESCRIPTION 4506 "Bridging of Ethernet traffic from Second Data Service 4507 has been disabled because the wireless link is not 4508 operating at the configured Lowest Second Data Modulation 4509 Mode" 4510 ::= { alarms 24 } 4511 4512 transparentClockSourcePortAlarm OBJECT-TYPE 4513 SYNTAX INTEGER { 4514 ok(0), 4515 invalidTransparentClockSourcePort(1) 4516 } 4517 MAX-ACCESS read-only 4518 STATUS current 4519 DESCRIPTION 4520 "Transparent Clock will not function properly because 4521 SFP, the selected clock source port is not FIBER" 4522 ::= { alarms 25 } 4523 4524 -- Smtp group attribute definitions 4525 -- 4526 sMTPEmailAlert OBJECT-TYPE 4527 SYNTAX INTEGER { 4528 disabled(0), 4529 enabled(1) 4530 } 4531 MAX-ACCESS read-write 4532 STATUS current 4533 DESCRIPTION 4534 "Simple Mail Transfer Protocol is used to send equipment 4535 alerts via email to a specified email address" 4536 ::= { smtp 1 } 4537 4538 sMTPServerPortNumber OBJECT-TYPE 4539 SYNTAX INTEGER (0..65535) 4540 MAX-ACCESS read-write 4541 STATUS current 4542 DESCRIPTION 4543 "Port number of the SMTP server" 4544 ::= { smtp 3 } 4545 4546 sMTPSourceEmailAddress OBJECT-TYPE 4547 SYNTAX DisplayString (SIZE(0..63)) 4548 MAX-ACCESS read-write 4549 STATUS current 4550 DESCRIPTION 4551 "The 'from' email address used when constructing the 4552 automatically generated e-mail message" 4553 ::= { smtp 4 } 4554 4555 sMTPDestinationEmailAddress OBJECT-TYPE 4556 SYNTAX DisplayString (SIZE(0..63)) 4557 MAX-ACCESS read-write 4558 STATUS current 4559 DESCRIPTION 4560 "The 'to' email address used when constructing the 4561 automatically generated e-mail message" 4562 ::= { smtp 5 } 4563 4564 sMTPEnabledMessages OBJECT-TYPE 4565 SYNTAX BITS { 4566 nIDULanPortUpDown(0), 4567 sFPPortUpDown(1), 4568 auxPortUpDown(2), 4569 mainPSUPortUpDown(3), 4570 enabledDiagnosticAlarms(4), 4571 dFSImpulseInterference(5), 4572 channelChange(6), 4573 wirelessLinkUpDown(7) 4574 } 4575 MAX-ACCESS read-write 4576 STATUS current 4577 DESCRIPTION 4578 "This controls which SMTP messages the unit will send" 4579 ::= { smtp 6 } 4580 4581 sMTPServerInternetAddressType OBJECT-TYPE 4582 SYNTAX INTEGER { 4583 unknown(0), 4584 ipv4(1), 4585 ipv6(2), 4586 ipv4z(3), 4587 ipv6z(4), 4588 unknown6(5), 4589 unknown7(6), 4590 unknown8(7), 4591 unknown9(8), 4592 unknown10(9), 4593 unknown11(10), 4594 unknown12(11), 4595 unknown13(12), 4596 unknown14(13), 4597 unknown15(14), 4598 unknown16(15), 4599 dns(16) 4600 } 4601 MAX-ACCESS read-only 4602 STATUS current 4603 DESCRIPTION 4604 "The type of Internet address specified by the associated 4605 sMTPServerInternetAddress." 4606 ::= { smtp 7 } 4607 4608 sMTPServerInternetAddress OBJECT-TYPE 4609 SYNTAX InetAddress 4610 MAX-ACCESS read-write 4611 STATUS current 4612 DESCRIPTION 4613 "Internet address of the SMTP server" 4614 ::= { smtp 8 } 4615 4616 -- SnmpControl group attribute definitions 4617 -- 4618 sNMPPortNumber OBJECT-TYPE 4619 SYNTAX INTEGER (0..65535) 4620 MAX-ACCESS read-write 4621 STATUS current 4622 DESCRIPTION 4623 "The IP port number used to access the SNMP MIB (i.e. 4624 Gets and Sets) (default = 161). NB: A system reboot is 4625 required to activate changes to this attribute" 4626 ::= { snmpControl 1 } 4627 4628 sNMPCommunityString OBJECT-TYPE 4629 SYNTAX DisplayString (SIZE(0..63)) 4630 MAX-ACCESS read-write 4631 STATUS current 4632 DESCRIPTION 4633 "The SNMP community string. NB: A system reboot is 4634 required to activate changes to this attribute" 4635 ::= { snmpControl 2 } 4636 4637 sNMPTrapTableNumber OBJECT-TYPE 4638 SYNTAX INTEGER (2) 4639 MAX-ACCESS read-only 4640 STATUS current 4641 DESCRIPTION 4642 "Number of entries in the sNMPTrapTable." 4643 ::= { snmpControl 3 } 4644 4645 sNMPTrapVersion OBJECT-TYPE 4646 SYNTAX INTEGER { 4647 v1(0), 4648 v2c(1) 4649 } 4650 MAX-ACCESS read-write 4651 STATUS current 4652 DESCRIPTION 4653 "The SNMP protocol version to use for SNMP Traps. NB: A 4654 system reboot is required to activate changes to this 4655 attribute" 4656 ::= { snmpControl 5 } 4657 4658 sNMPEnabledTraps OBJECT-TYPE 4659 SYNTAX BITS { 4660 auxPortUpDown(0), 4661 mainPSUPortUpDown(1), 4662 authenticationFailure(2), 4663 enabledDiagnosticAlarms(3), 4664 dFSImpulseInterference(4), 4665 channelChange(5), 4666 wirelessLinkUpDown(6), 4667 coldStart(7), 4668 nIDULanPortUpDown(14), 4669 sFPPortUpDown(15) 4670 } 4671 MAX-ACCESS read-write 4672 STATUS current 4673 DESCRIPTION 4674 "This controls which SNMP Traps the unit will send" 4675 ::= { snmpControl 6 } 4676 4677 enabledDiagnosticAlarms OBJECT-TYPE 4678 SYNTAX BITS { 4679 portState(0), 4680 incompatibleMasterAndSlave(1), 4681 incompatibleRegulatoryBands(2), 4682 maximumLinkRangeExceeded(3), 4683 unitOutOfCalibration(4), 4684 installArmState(5), 4685 installStatus(6), 4686 regulatoryBand(7), 4687 syslogLocalWrapped(8), 4688 syslogLocalNearlyFull(9), 4689 syslogDisabledWarning(10), 4690 linkModeOptimizationMismatch(11), 4691 tDDSynchronizationAlarm(12), 4692 wirelessLinkDisabledWarning(13), 4693 sNTPSynchronizationFailed(14), 4694 noWirelessChannelAvailable(15), 4695 tDMAlarms(18), 4696 capacityVariantMismatch(19), 4697 remainingFullCapacityTrialTime(20), 4698 dataBridgingStatus(21), 4699 unknown18(22), 4700 syslogClientDisabledWarning(23) 4701 } 4702 MAX-ACCESS read-write 4703 STATUS current 4704 DESCRIPTION 4705 "Controls which individual diagnostic alarms are enabled. 4706 The unit may be configured to generate SNMP traps and/or 4707 SMTP email alerts for these enabled alarms by selecting 4708 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' 4709 and/or 'SMTP Enabled Messages' attributes" 4710 ::= { snmpControl 7 } 4711 4712 sNMPSendAllTrapsAtStartup OBJECT-TYPE 4713 SYNTAX INTEGER { 4714 disabled(0), 4715 enabled(1) 4716 } 4717 MAX-ACCESS read-write 4718 STATUS current 4719 DESCRIPTION 4720 "Controls whether cleared traps are reported at start-up 4721 as well as raised traps. Only enabled traps will be 4722 reported. NB: Traps corresponding to transient events 4723 (i.e. not associated with an alarm or status value) are 4724 only sent when required and not at start-up." 4725 ::= { snmpControl 8 } 4726 4727 -- SNMPTrapTable group attribute definitions 4728 -- 4729 sNMPTrapTableIndex OBJECT-TYPE 4730 SYNTAX INTEGER (1..2) 4731 MAX-ACCESS not-accessible 4732 STATUS current 4733 DESCRIPTION 4734 "SNMP trap value, used to index the SNMPTrapTable." 4735 ::= { sNMPTrapTableEntry 1 } 4736 4737 sNMPTrapPortNumber OBJECT-TYPE 4738 SYNTAX INTEGER (0..65535) 4739 MAX-ACCESS read-write 4740 STATUS current 4741 DESCRIPTION 4742 "Destination port for SNMP Traps (default=162). NB: A 4743 system reboot is required to activate changes to this 4744 attribute." 4745 ::= { sNMPTrapTableEntry 3 } 4746 4747 sNMPTrapInternetAddressType OBJECT-TYPE 4748 SYNTAX INTEGER { 4749 unknown(0), 4750 ipv4(1), 4751 ipv6(2), 4752 ipv4z(3), 4753 ipv6z(4), 4754 unknown6(5), 4755 unknown7(6), 4756 unknown8(7), 4757 unknown9(8), 4758 unknown10(9), 4759 unknown11(10), 4760 unknown12(11), 4761 unknown13(12), 4762 unknown14(13), 4763 unknown15(14), 4764 unknown16(15), 4765 dns(16) 4766 } 4767 MAX-ACCESS read-only 4768 STATUS current 4769 DESCRIPTION 4770 "The type of Internet address specified by the associated 4771 sNMPTrapInternetAddress." 4772 ::= { sNMPTrapTableEntry 4 } 4773 4774 sNMPTrapInternetAddress OBJECT-TYPE 4775 SYNTAX InetAddress 4776 MAX-ACCESS read-write 4777 STATUS current 4778 DESCRIPTION 4779 "The Internet address to which all SNMP Traps are sent." 4780 ::= { sNMPTrapTableEntry 5 } 4781 4782 sNMPTrapReceiverEnabled OBJECT-TYPE 4783 SYNTAX INTEGER { 4784 disabled(0), 4785 enabled(1) 4786 } 4787 MAX-ACCESS read-write 4788 STATUS current 4789 DESCRIPTION 4790 "A value of 0 disables the sending of SNMP trap to 4791 corresponding receiver. A value of 1 enables the sending 4792 of SNMP trap to corresponding receiver." 4793 ::= { sNMPTrapTableEntry 6 } 4794 4795 -- Sntp group attribute definitions 4796 -- 4797 sNTPState OBJECT-TYPE 4798 SYNTAX INTEGER { 4799 disabled(0), 4800 enabled(1) 4801 } 4802 MAX-ACCESS read-write 4803 STATUS current 4804 DESCRIPTION 4805 "SNTP control state" 4806 ::= { sntp 1 } 4807 4808 sNTPPollInterval OBJECT-TYPE 4809 SYNTAX INTEGER (60..43200) 4810 MAX-ACCESS read-write 4811 STATUS current 4812 DESCRIPTION 4813 "The SNTP server polling interval" 4814 ::= { sntp 4 } 4815 4816 sNTPSync OBJECT-TYPE 4817 SYNTAX INTEGER { 4818 noSync(0), 4819 inSync(1) 4820 } 4821 MAX-ACCESS read-only 4822 STATUS current 4823 DESCRIPTION 4824 "If SNTP Sync fails then check the server settings in the 4825 Remote Management page, or disable SNTP" 4826 ::= { sntp 5 } 4827 4828 sNTPLastSync OBJECT-TYPE 4829 SYNTAX Integer32 4830 MAX-ACCESS read-only 4831 STATUS current 4832 DESCRIPTION 4833 "Last SNTP sync time" 4834 ::= { sntp 6 } 4835 4836 systemClock OBJECT-TYPE 4837 SYNTAX Integer32 4838 MAX-ACCESS read-only 4839 STATUS current 4840 DESCRIPTION 4841 "System clock presented as local time" 4842 ::= { sntp 7 } 4843 4844 timeZone OBJECT-TYPE 4845 SYNTAX INTEGER { 4846 gmtMinus1200(0), 4847 gmtMinus1130(1), 4848 gmtMinus1100(2), 4849 gmtMinus1030(3), 4850 gmtMinus1000(4), 4851 gmtMinus0930(5), 4852 gmtMinus0900(6), 4853 gmtMinus0830(7), 4854 gmtMinus0800(8), 4855 gmtMinus0730(9), 4856 gmtMinus0700(10), 4857 gmtMinus0630(11), 4858 gmtMinus0600(12), 4859 gmtMinus0530(13), 4860 gmtMinus0500(14), 4861 gmtMinus0430(15), 4862 gmtMinus0400(16), 4863 gmtMinus0330(17), 4864 gmtMinus0300(18), 4865 gmtMinus0230(19), 4866 gmtMinus0200(20), 4867 gmtMinus0130(21), 4868 gmtMinus0100(22), 4869 gmtMinus0030(23), 4870 gmtZero(24), 4871 gmtPlus0030(25), 4872 gmtPlus0100(26), 4873 gmtPlus0130(27), 4874 gmtPlus0200(28), 4875 gmtPlus0230(29), 4876 gmtPlus0300(30), 4877 gmtPlus0330(31), 4878 gmtPlus0400(32), 4879 gmtPlus0430(33), 4880 gmtPlus0500(34), 4881 gmtPlus0530(35), 4882 gmtPlus0600(36), 4883 gmtPlus0630(37), 4884 gmtPlus0700(38), 4885 gmtPlus0730(39), 4886 gmtPlus0800(40), 4887 gmtPlus0830(41), 4888 gmtPlus0900(42), 4889 gmtPlus0930(43), 4890 gmtPlus1000(44), 4891 gmtPlus1030(45), 4892 gmtPlus1100(46), 4893 gmtPlus1130(47), 4894 gmtPlus1200(48), 4895 gmtPlus1230(49), 4896 gmtPlus1300(50) 4897 } 4898 MAX-ACCESS read-write 4899 STATUS current 4900 DESCRIPTION 4901 "Time zone offsets from Greenwich Mean Time (GMT)" 4902 ::= { sntp 8 } 4903 4904 daylightSaving OBJECT-TYPE 4905 SYNTAX INTEGER { 4906 disabled(0), 4907 enabled(1) 4908 } 4909 MAX-ACCESS read-write 4910 STATUS current 4911 DESCRIPTION 4912 "Daylight Saving Time" 4913 ::= { sntp 9 } 4914 4915 sNTPPrimaryServer OBJECT-TYPE 4916 SYNTAX INTEGER { 4917 server1(0), 4918 server2(1) 4919 } 4920 MAX-ACCESS read-write 4921 STATUS current 4922 DESCRIPTION 4923 "Specifies the primary SNTP server, determining the order 4924 in which the servers are tried." 4925 ::= { sntp 10 } 4926 4927 sNTPPrimaryServerDeadTime OBJECT-TYPE 4928 SYNTAX INTEGER (0..86400) 4929 MAX-ACCESS read-write 4930 STATUS current 4931 DESCRIPTION 4932 "Time (in seconds) to wait before retrying communications 4933 with an unresponsive primary SNTP server. Setting the 4934 value to 0 disables the timer." 4935 ::= { sntp 11 } 4936 4937 sNTPServerRetries OBJECT-TYPE 4938 SYNTAX INTEGER (0..10) 4939 MAX-ACCESS read-write 4940 STATUS current 4941 DESCRIPTION 4942 "Number of times the PTP will retry after an SNTP server 4943 fails to respond." 4944 ::= { sntp 12 } 4945 4946 sNTPServerTimeout OBJECT-TYPE 4947 SYNTAX INTEGER (1..15) 4948 MAX-ACCESS read-write 4949 STATUS current 4950 DESCRIPTION 4951 "Time (in seconds) the PTP will wait for a response from 4952 an SNTP server." 4953 ::= { sntp 13 } 4954 4955 sNTPServerTableNumber OBJECT-TYPE 4956 SYNTAX INTEGER (2) 4957 MAX-ACCESS read-only 4958 STATUS current 4959 DESCRIPTION 4960 "Number of entries in the SNTPServerTable." 4961 ::= { sntp 14 } 4962 4963 -- SNTPServerTable group attribute definitions 4964 -- 4965 sNTPServerTableIndex OBJECT-TYPE 4966 SYNTAX INTEGER (1..2) 4967 MAX-ACCESS not-accessible 4968 STATUS current 4969 DESCRIPTION 4970 "Index range for the SNTPServerTable." 4971 ::= { sNTPServerTableEntry 1 } 4972 4973 sNTPServerPortNumber OBJECT-TYPE 4974 SYNTAX INTEGER (0..65535) 4975 MAX-ACCESS read-write 4976 STATUS current 4977 DESCRIPTION 4978 "The IP port number of the SNTP server. Defaults to port 4979 123." 4980 ::= { sNTPServerTableEntry 3 } 4981 4982 sNTPServerStatus OBJECT-TYPE 4983 SYNTAX DisplayString (SIZE(0..127)) 4984 MAX-ACCESS read-only 4985 STATUS current 4986 DESCRIPTION 4987 "Status message reflecting the result of communications 4988 with the SNTP server when last polled" 4989 ::= { sNTPServerTableEntry 4 } 4990 4991 sNTPServerInternetAddressType OBJECT-TYPE 4992 SYNTAX INTEGER { 4993 unknown(0), 4994 ipv4(1), 4995 ipv6(2), 4996 ipv4z(3), 4997 ipv6z(4), 4998 unknown6(5), 4999 unknown7(6), 5000 unknown8(7), 5001 unknown9(8), 5002 unknown10(9), 5003 unknown11(10), 5004 unknown12(11), 5005 unknown13(12), 5006 unknown14(13), 5007 unknown15(14), 5008 unknown16(15), 5009 dns(16) 5010 } 5011 MAX-ACCESS read-only 5012 STATUS current 5013 DESCRIPTION 5014 "The type of Internet address specified by the associated 5015 sNTPServerInternetAddress." 5016 ::= { sNTPServerTableEntry 5 } 5017 5018 sNTPServerInternetAddress OBJECT-TYPE 5019 SYNTAX InetAddress 5020 MAX-ACCESS read-write 5021 STATUS current 5022 DESCRIPTION 5023 "The Internet address of a valid SNTP server" 5024 ::= { sNTPServerTableEntry 6 } 5025 5026 -- Reset group attribute definitions 5027 -- 5028 systemReset OBJECT-TYPE 5029 SYNTAX INTEGER { 5030 running(0), 5031 consoleReboot(1) 5032 } 5033 MAX-ACCESS read-write 5034 STATUS current 5035 DESCRIPTION 5036 "Setting this attribute to '1' will cause a system 5037 reboot. NB: a system reboot will apply any pending new 5038 settings held in memory" 5039 ::= { reset 1 } 5040 5041 -- Versions group attribute definitions 5042 -- 5043 softwareVersion OBJECT-TYPE 5044 SYNTAX DisplayString (SIZE(0..63)) 5045 MAX-ACCESS read-only 5046 STATUS current 5047 DESCRIPTION 5048 "Current software version" 5049 ::= { versions 1 } 5050 5051 hardwareVersion OBJECT-TYPE 5052 SYNTAX DisplayString (SIZE(0..63)) 5053 MAX-ACCESS read-only 5054 STATUS current 5055 DESCRIPTION 5056 "Hardware platform version" 5057 ::= { versions 2 } 5058 5059 secondarySoftwareVersion OBJECT-TYPE 5060 SYNTAX DisplayString (SIZE(0..63)) 5061 MAX-ACCESS read-only 5062 STATUS current 5063 DESCRIPTION 5064 "Secondary software version, used when the primary 5065 software image is invalid or erased" 5066 ::= { versions 3 } 5067 5068 bootVersion OBJECT-TYPE 5069 SYNTAX DisplayString (SIZE(0..63)) 5070 MAX-ACCESS read-only 5071 STATUS current 5072 DESCRIPTION 5073 "Boot code software version" 5074 ::= { versions 4 } 5075 5076 -- PubStats group attribute definitions 5077 -- 5078 receiveDataRate OBJECT-TYPE 5079 SYNTAX Integer32 5080 MAX-ACCESS read-only 5081 STATUS current 5082 DESCRIPTION 5083 "Average data rate over the last one second interval 5084 (kbps)" 5085 ::= { pubStats 1 } 5086 5087 transmitDataRate OBJECT-TYPE 5088 SYNTAX Integer32 5089 MAX-ACCESS read-only 5090 STATUS current 5091 DESCRIPTION 5092 "Average data rate over the last one second interval 5093 (kbps)" 5094 ::= { pubStats 2 } 5095 5096 aggregateDataRate OBJECT-TYPE 5097 SYNTAX Integer32 5098 MAX-ACCESS read-only 5099 STATUS current 5100 DESCRIPTION 5101 "Average data rate over the last one second interval 5102 (kbps)" 5103 ::= { pubStats 3 } 5104 5105 wirelessLinkAvailability OBJECT-TYPE 5106 SYNTAX INTEGER (0..1000000) 5107 MAX-ACCESS read-only 5108 STATUS current 5109 DESCRIPTION 5110 "Link availability calculated since the last reset of the 5111 system counters, as a percentage multiplied by 10000 to 5112 give four decimal places of precision" 5113 ::= { pubStats 4 } 5114 5115 wirelessLinkStatus OBJECT-TYPE 5116 SYNTAX INTEGER { 5117 up(0), 5118 registering(1), 5119 searching(2), 5120 acquiring(3), 5121 radarCAC(4), 5122 initialising(5) 5123 } 5124 MAX-ACCESS read-only 5125 STATUS current 5126 DESCRIPTION 5127 "Current status of the wireless link" 5128 ::= { pubStats 5 } 5129 5130 byteErrorRatio OBJECT-TYPE 5131 SYNTAX Integer32 5132 MAX-ACCESS read-only 5133 STATUS current 5134 DESCRIPTION 5135 "Reciprocal of the byte error ratio calculated since the 5136 last reset of the system counters" 5137 ::= { pubStats 6 } 5138 5139 receiveModulationModeDetail OBJECT-TYPE 5140 SYNTAX INTEGER { 5141 runningAtMaximumReceiveMode(0), 5142 runningAtUserConfiguredMaxModulationMode(1), 5143 restrictedBecauseInstallationIsArmed(2), 5144 restrictedBecauseOfByteErrorsOnTheWirelessLink(3), 5145 restrictedBecauseTheLinkParametersAreUpdating(4), 5146 restrictedBecauseChannelChangeIsInProgress(5), 5147 restrictedDueToTheLowEthernetLinkSpeed(6), 5148 runningAtMaximumReceiveModeForChannelBandwidth(7), 5149 limitedByTheWirelessConditions(8), 5150 restrictedBecauseFullCapabilityTrialLicenseExpired(9) 5151 } 5152 MAX-ACCESS read-only 5153 STATUS current 5154 DESCRIPTION 5155 "The reason for the current receive modulation mode" 5156 ::= { pubStats 7 } 5157 5158 dataBridgingAvailability OBJECT-TYPE 5159 SYNTAX INTEGER (0..1000000) 5160 MAX-ACCESS read-only 5161 STATUS current 5162 DESCRIPTION 5163 "Link availability bridging Ethernet Data traffic 5164 calculated since the last reset of the system counters, 5165 as a percentage multiplied by 10000 to give four decimal 5166 places of precision" 5167 ::= { pubStats 8 } 5168 5169 -- Encryption group attribute definitions 5170 -- 5171 encryptionAlgorithm OBJECT-TYPE 5172 SYNTAX INTEGER { 5173 none(0), 5174 aESRijndael(1), 5175 aES192bitRijndael(2), 5176 aES256bitRijndael(3) 5177 } 5178 MAX-ACCESS read-only 5179 STATUS current 5180 DESCRIPTION 5181 "The Encryption Algorithm used by the wireless link. NB: 5182 A system reboot is required to activate changes to this 5183 attribute. NB: The same Encryption Algorithm must be 5184 configured at BOTH ends of the link for it to function 5185 correctly" 5186 ::= { encryption 1 } 5187 5188 -- TDDControl group attribute definitions 5189 -- 5190 tDDSynchronizationMode OBJECT-TYPE 5191 SYNTAX INTEGER { 5192 disabled(0), 5193 enabled(1) 5194 } 5195 MAX-ACCESS read-only 5196 STATUS current 5197 DESCRIPTION 5198 "TDD Synchronization Mode selection" 5199 ::= { tDDControl 1 } 5200 5201 -- AAAControl group attribute definitions 5202 -- 5203 userTableNumber OBJECT-TYPE 5204 SYNTAX INTEGER (1..10) 5205 MAX-ACCESS read-only 5206 STATUS current 5207 DESCRIPTION 5208 "Number of entries in the userTable" 5209 ::= { aAAControl 1 } 5210 5211 -- UserTable group attribute definitions 5212 -- 5213 userTableIndex OBJECT-TYPE 5214 SYNTAX INTEGER (1..10) 5215 MAX-ACCESS not-accessible 5216 STATUS current 5217 DESCRIPTION 5218 "used to index values in the userTable." 5219 ::= { userTableEntry 1 } 5220 5221 userName OBJECT-TYPE 5222 SYNTAX DisplayString (SIZE(0..67)) 5223 MAX-ACCESS read-only 5224 STATUS current 5225 DESCRIPTION 5226 "User name which must be entered, along with the 5227 appropriate password, in order to gain access to the 5228 system." 5229 ::= { userTableEntry 2 } 5230 5231 userRole OBJECT-TYPE 5232 SYNTAX INTEGER { 5233 readOnly(0), 5234 systemAdministrator(1), 5235 securityOfficer(2) 5236 } 5237 MAX-ACCESS read-only 5238 STATUS current 5239 DESCRIPTION 5240 "Role of the selected user. A Security Officer has access 5241 to and can modify all settings. A System Administrator 5242 has access to and can modify all non-security settings. A 5243 Read Only user can view settings, but cannot make any 5244 changes." 5245 ::= { userTableEntry 3 } 5246 5247 userEnabled OBJECT-TYPE 5248 SYNTAX INTEGER { 5249 disabled(0), 5250 enabled(1) 5251 } 5252 MAX-ACCESS read-only 5253 STATUS current 5254 DESCRIPTION 5255 "Enable / Disable the selected user" 5256 ::= { userTableEntry 4 } 5257 5258 userPassword OBJECT-TYPE 5259 SYNTAX DisplayString (SIZE(0..67)) 5260 MAX-ACCESS read-write 5261 STATUS current 5262 DESCRIPTION 5263 "User password, which must be entered in order to gain 5264 access to the system." 5265 ::= { userTableEntry 5 } 5266 5267 -- SyslogControl group attribute definitions 5268 -- 5269 syslogClient OBJECT-TYPE 5270 SYNTAX INTEGER { 5271 disabled(0), 5272 enabled(1) 5273 } 5274 MAX-ACCESS read-only 5275 STATUS current 5276 DESCRIPTION 5277 "Enable or disable the syslog client" 5278 ::= { syslogControl 1 } 5279 5280 syslogState OBJECT-TYPE 5281 SYNTAX INTEGER { 5282 disabled(0), 5283 enabled(1) 5284 } 5285 MAX-ACCESS read-only 5286 STATUS current 5287 DESCRIPTION 5288 "The syslog service has been enabled or disabled" 5289 ::= { syslogControl 2 } 5290 5291 -- RouterProtocols group attribute definitions 5292 -- 5293 microwaveAdaptiveBandwidth OBJECT-TYPE 5294 SYNTAX INTEGER { 5295 disabled(0), 5296 enabled(1) 5297 } 5298 MAX-ACCESS read-only 5299 STATUS current 5300 DESCRIPTION 5301 "Enable support of Microwave Adaptive Bandwidth Protocol. 5302 MAB is disabled if link symmetry is configured as 5303 Adaptive" 5304 ::= { routerProtocols 1 } 5305 5306 mABNominalModulationMode OBJECT-TYPE 5307 SYNTAX INTEGER { 5308 modAcquisition(0), 5309 modBpsk63percent(1), 5310 modQpsk63percentSingle(2), 5311 modTransient1(3), 5312 modQpsk87percentSingle(4), 5313 modTransient2(5), 5314 mod16qam63percentSingleA(6), 5315 modTransient3(7), 5316 mod16qam87percentSingle(8), 5317 modTransient4(9), 5318 mod64qam75percentSingle(10), 5319 modTransient5(11), 5320 mod64qam92percentSingle(12), 5321 modTransient6(13), 5322 mod256qam81percentSingle(14), 5323 mod16qam63percentSingleB(15), 5324 mod16qam63percentDual(16), 5325 modTransient7(17), 5326 mod16qam87percentDual(18), 5327 modTransient8(19), 5328 mod64qam75percentDual(20), 5329 modTransient9(21), 5330 mod64qam92percentDual(22), 5331 modTransient10(23), 5332 mod256qam81percentDual(24) 5333 } 5334 MAX-ACCESS read-only 5335 STATUS current 5336 DESCRIPTION 5337 "The Nominal modulation mode is the desired modulation 5338 mode. MAB VSM packets are generated when the current 5339 modulation mode falls below the nominal modulation." 5340 ::= { routerProtocols 2 } 5341 5342 mABTransmissionInterval OBJECT-TYPE 5343 SYNTAX INTEGER { 5344 transmissionInterval1s(0), 5345 transmissionInterval10s(1), 5346 transmissionInterval60s(2) 5347 } 5348 MAX-ACCESS read-only 5349 STATUS current 5350 DESCRIPTION 5351 "The minimum interval (in seconds) between successive MAB 5352 vendor specific messages (VSM). These VSM are sent when 5353 the current transmit capacity falls below the configured 5354 MAB Nominal Modulation Mode." 5355 ::= { routerProtocols 3 } 5356 5357 mABHoldoffPeriod OBJECT-TYPE 5358 SYNTAX INTEGER (10..60) 5359 MAX-ACCESS read-only 5360 STATUS current 5361 DESCRIPTION 5362 "The period (in seconds) over which transmit capacity is 5363 averaged over to determine when the wireless link has 5364 degraded" 5365 ::= { routerProtocols 4 } 5366 5367 mABMaintenanceLevel OBJECT-TYPE 5368 SYNTAX INTEGER (0..7) 5369 MAX-ACCESS read-only 5370 STATUS current 5371 DESCRIPTION 5372 "Maintenance Levels (0-7) determines the destination MAC 5373 address of MAB vendor specific messages." 5374 ::= { routerProtocols 5 } 5375 5376 useVLANForMABProtocol OBJECT-TYPE 5377 SYNTAX INTEGER { 5378 noVLANTagging(0), 5379 iEEE8021QTaggedCTagType8100(1) 5380 } 5381 MAX-ACCESS read-only 5382 STATUS current 5383 DESCRIPTION 5384 "This controls whether MAB vendor specific messages (VSM) 5385 packets use VLAN tags or not." 5386 ::= { routerProtocols 6 } 5387 5388 mABProtocolVID OBJECT-TYPE 5389 SYNTAX INTEGER (0..4094) 5390 MAX-ACCESS read-only 5391 STATUS current 5392 DESCRIPTION 5393 "This VLAN VID (0-4094) will be included in MAB vendor 5394 specific messages (VSM) packets." 5395 ::= { routerProtocols 7 } 5396 5397 mABProtocolVLANPriority OBJECT-TYPE 5398 SYNTAX INTEGER (0..7) 5399 MAX-ACCESS read-only 5400 STATUS current 5401 DESCRIPTION 5402 "This VLAN Priority (0-7) will be included in MAB vendor 5403 specific messages (VSM) packets." 5404 ::= { routerProtocols 8 } 5405 5406 mABState OBJECT-TYPE 5407 SYNTAX INTEGER { 5408 normal(0), 5409 degraded(1) 5410 } 5411 MAX-ACCESS read-only 5412 STATUS current 5413 DESCRIPTION 5414 "Current state of MAB Protocol. A state of 'Normal' on a 5415 green background indicates that a PTP link is operating 5416 at nominal capacity" 5417 ::= { routerProtocols 9 } 5418 5419 mABNominalTransmitCapacity OBJECT-TYPE 5420 SYNTAX INTEGER (0..1000) 5421 MAX-ACCESS read-only 5422 STATUS current 5423 DESCRIPTION 5424 "The nominal Tx capacity used in MAB Vendor Specific 5425 Messages for the selected nominal modulation mode " 5426 ::= { routerProtocols 10 } 5427 5428 mABCurrentTransmitCapacity OBJECT-TYPE 5429 SYNTAX INTEGER (0..1000) 5430 MAX-ACCESS read-only 5431 STATUS current 5432 DESCRIPTION 5433 "The current Tx capacity of the wireless link used in the 5434 last MAB Vendor Specific Message transmitted." 5435 ::= { routerProtocols 11 } 5436 5437 -- CableDiagnostics group attribute definitions 5438 -- 5439 cableDiagnosticsPorts OBJECT-TYPE 5440 SYNTAX BITS { 5441 auxPort(6), 5442 mainPSUPort(7) 5443 } 5444 MAX-ACCESS read-write 5445 STATUS current 5446 DESCRIPTION 5447 "Select ports on which Cable Diagnostics must be 5448 executed" 5449 ::= { cableDiagnostics 1 } 5450 5451 cableDiagnosticsControl OBJECT-TYPE 5452 SYNTAX INTEGER { 5453 startTest(0), 5454 testInProgress(1) 5455 } 5456 MAX-ACCESS read-write 5457 STATUS current 5458 DESCRIPTION 5459 "Set this attribute to 'Test in Progress' to start a 5460 Cable Diagnostics test" 5461 ::= { cableDiagnostics 2 } 5462 5463 cableDiagnosticsWarning OBJECT-TYPE 5464 SYNTAX INTEGER { 5465 idle(0), 5466 testInProgress(1) 5467 } 5468 MAX-ACCESS read-only 5469 STATUS current 5470 DESCRIPTION 5471 "Normal Ethernet operation is disrupted when a Cable 5472 Diagnostics test is in progress" 5473 ::= { cableDiagnostics 3 } 5474 5475 cableDiagnosticsResultTableNumber OBJECT-TYPE 5476 SYNTAX INTEGER (1..2) 5477 MAX-ACCESS read-only 5478 STATUS current 5479 DESCRIPTION 5480 "Number of rows in the Cable Diagnostics Result Table." 5481 ::= { cableDiagnostics 4 } 5482 5483 -- CableDiagnosticsResultTable group attribute definitions 5484 -- 5485 cableDiagnosticsResultTableIndex OBJECT-TYPE 5486 SYNTAX INTEGER (1..2) 5487 MAX-ACCESS not-accessible 5488 STATUS current 5489 DESCRIPTION 5490 "Cable Diagnostics Port value used to index into the 5491 result table." 5492 ::= { cableDiagnosticsResultTableEntry 1 } 5493 5494 cableDiagnosticsResultsDateTime OBJECT-TYPE 5495 SYNTAX Integer32 5496 MAX-ACCESS read-only 5497 STATUS current 5498 DESCRIPTION 5499 "The Date and Time when a Cable Diagnostics test was last 5500 executed" 5501 ::= { cableDiagnosticsResultTableEntry 2 } 5502 5503 cableDiagPair1Results OBJECT-TYPE 5504 SYNTAX INTEGER { 5505 ok(0), 5506 unknown(1), 5507 inProgress(2), 5508 notTested(3), 5509 openCircuit(4), 5510 shortCircuit(5) 5511 } 5512 MAX-ACCESS read-only 5513 STATUS current 5514 DESCRIPTION 5515 "The result of the most recent execution of Cable 5516 Diagnostics on cable pair 1. According to the T658B 5517 wiring scheme, pair 1 is pins 4 & 5 on the RJ45 socket on 5518 the ODU. Open Circuit is reported when the impedance is 5519 greater than 330 ohms. Short Circuit is reported when the 5520 impedance is less than 33 ohms. Unknown is reported when 5521 a continuous signal is received from the link partner for 5522 125 ms, preventing start of the test." 5523 ::= { cableDiagnosticsResultTableEntry 3 } 5524 5525 cableDiagPair1Distance OBJECT-TYPE 5526 SYNTAX Integer32 5527 MAX-ACCESS read-only 5528 STATUS current 5529 DESCRIPTION 5530 "The distance in meters from the ODU to the fault 5531 detected on the cable pair during the most recent 5532 execution of Cable Diagnostics. Faults in cables longer 5533 than 160 meters (525 feet) may not be detected. The error 5534 margin is +/-2 meters (6.5 feet)." 5535 ::= { cableDiagnosticsResultTableEntry 4 } 5536 5537 cableDiagPair2Results OBJECT-TYPE 5538 SYNTAX INTEGER { 5539 ok(0), 5540 unknown(1), 5541 inProgress(2), 5542 notTested(3), 5543 openCircuit(4), 5544 shortCircuit(5) 5545 } 5546 MAX-ACCESS read-only 5547 STATUS current 5548 DESCRIPTION 5549 "The result of the most recent execution of Cable 5550 Diagnostics on cable pair 2. According to the T658B 5551 wiring scheme, pair 2 is pins 1 & 2 on the RJ45 socket on 5552 the ODU. Open Circuit is reported when the impedance is 5553 greater than 330 ohms. Short Circuit is reported when the 5554 impedance is less than 33 ohms. Unknown is reported when 5555 a continuous signal is received from the link partner for 5556 125 ms, preventing start of the test." 5557 ::= { cableDiagnosticsResultTableEntry 5 } 5558 5559 cableDiagPair2Distance OBJECT-TYPE 5560 SYNTAX Integer32 5561 MAX-ACCESS read-only 5562 STATUS current 5563 DESCRIPTION 5564 "The distance in meters from the ODU to the fault 5565 detected on the cable pair during the most recent 5566 execution of Cable Diagnostics. Faults in cables longer 5567 than 160 meters (525 feet) may not be detected. The error 5568 margin is +/-2 meters (6.5 feet)." 5569 ::= { cableDiagnosticsResultTableEntry 6 } 5570 5571 cableDiagPair3Results OBJECT-TYPE 5572 SYNTAX INTEGER { 5573 ok(0), 5574 unknown(1), 5575 inProgress(2), 5576 notTested(3), 5577 openCircuit(4), 5578 shortCircuit(5) 5579 } 5580 MAX-ACCESS read-only 5581 STATUS current 5582 DESCRIPTION 5583 "The result of the most recent execution of Cable 5584 Diagnostics on cable pair 3. According to the T658B 5585 wiring scheme, pair 3 is pins 3 & 6 on the RJ45 socket on 5586 the ODU. Open Circuit is reported when the impedance is 5587 greater than 330 ohms. Short Circuit is reported when the 5588 impedance is less than 33 ohms. Unknown is reported when 5589 a continuous signal is received from the link partner for 5590 125 ms, preventing start of the test." 5591 ::= { cableDiagnosticsResultTableEntry 7 } 5592 5593 cableDiagPair3Distance OBJECT-TYPE 5594 SYNTAX Integer32 5595 MAX-ACCESS read-only 5596 STATUS current 5597 DESCRIPTION 5598 "The distance in meters from the ODU to the fault 5599 detected on the cable pair during the most recent 5600 execution of Cable Diagnostics. Faults in cables longer 5601 than 160 meters (525 feet) may not be detected. The error 5602 margin is +/-2 meters (6.5 feet)." 5603 ::= { cableDiagnosticsResultTableEntry 8 } 5604 5605 cableDiagPair4Results OBJECT-TYPE 5606 SYNTAX INTEGER { 5607 ok(0), 5608 unknown(1), 5609 inProgress(2), 5610 notTested(3), 5611 openCircuit(4), 5612 shortCircuit(5) 5613 } 5614 MAX-ACCESS read-only 5615 STATUS current 5616 DESCRIPTION 5617 "The result of the most recent execution of Cable 5618 Diagnostics on cable pair 4. According to the T658B 5619 wiring scheme, pair 4 is pins 7 & 8 on the RJ45 socket on 5620 the ODU. Open Circuit is reported when the impedance is 5621 greater than 330 ohms. Short Circuit is reported when the 5622 impedance is less than 33 ohms. Unknown is reported when 5623 a continuous signal is received from the link partner for 5624 125 ms, preventing start of the test." 5625 ::= { cableDiagnosticsResultTableEntry 9 } 5626 5627 cableDiagPair4Distance OBJECT-TYPE 5628 SYNTAX Integer32 5629 MAX-ACCESS read-only 5630 STATUS current 5631 DESCRIPTION 5632 "The distance in meters from the ODU to the fault 5633 detected on the cable pair during the most recent 5634 execution of Cable Diagnostics. Faults in cables longer 5635 than 160 meters (525 feet) may not be detected. The error 5636 margin is +/-2 meters (6.5 feet)." 5637 ::= { cableDiagnosticsResultTableEntry 10 } 5638 5639 -- Supplementary group attribute definitions 5640 -- 5641 longitude OBJECT-TYPE 5642 SYNTAX DisplayString (SIZE(0..19)) 5643 MAX-ACCESS read-write 5644 STATUS current 5645 DESCRIPTION 5646 "The longitude of the unit, measured in decimal degrees. 5647 This object is set by the SNMP manager and has no 5648 internal function." 5649 ::= { supplementary 1 } 5650 5651 latitude OBJECT-TYPE 5652 SYNTAX DisplayString (SIZE(0..19)) 5653 MAX-ACCESS read-write 5654 STATUS current 5655 DESCRIPTION 5656 "The latitude of the unit, measured in decimal degrees. 5657 This object is set by the SNMP manager and has no 5658 internal function." 5659 ::= { supplementary 2 } 5660 5661 altitude OBJECT-TYPE 5662 SYNTAX Integer32 5663 MAX-ACCESS read-write 5664 STATUS current 5665 DESCRIPTION 5666 "The altitude of the unit, measured in meters. This 5667 object is set by the SNMP manager and has no internal 5668 function." 5669 ::= { supplementary 3 } 5670 5671 -- Enterprise NOTIFICATION definitions 5672 -- 5673 5674 channelChangeTrap NOTIFICATION-TYPE 5675 OBJECTS { receiveChannel } 5676 STATUS current 5677 DESCRIPTION "The PTP radio has changed wireless channel. 5678 This has been caused by either 5679 i) mandatory radar avoidance, 5680 a DFS impulsive interference event will also be 5681 detected, 5682 or 5683 ii) Dynamic Spectrum Optimization, (DSO) 5684 DSO improves link performance by selecting the 5685 most appropriate transmit and receive channels 5686 with the lowest level of interference." 5687 ::= { ptpTrapPrefix 1 } 5688 5689 dfsImpulsiveInterferenceTrap NOTIFICATION-TYPE 5690 OBJECTS { receiveChannel } 5691 STATUS current 5692 DESCRIPTION "DFS impulsive interference detected event" 5693 ::= { ptpTrapPrefix 2 } 5694 5695 mainPSUPortStatusTrap NOTIFICATION-TYPE 5696 OBJECTS { mainPSUPortStatus } 5697 STATUS current 5698 DESCRIPTION 5699 "Current status of the Main PSU Ethernet link. NB: a 5700 change of state may generate an SNMP trap and/or SMTP 5701 email alert" 5702 ::= { ptpTrapPrefix 3 } 5703 5704 mainPSUPortDisabledWarningTrap NOTIFICATION-TYPE 5705 OBJECTS { mainPSUPortDisabledWarning } 5706 STATUS current 5707 DESCRIPTION 5708 "The SNMP ifAdminStatus of the interface has disabled 5709 Ethernet traffic" 5710 ::= { ptpTrapPrefix 4 } 5711 5712 mainPSUPortConfigurationMismatchTrap NOTIFICATION-TYPE 5713 OBJECTS { mainPSUPortConfigurationMismatch } 5714 STATUS current 5715 DESCRIPTION 5716 "The detection of Ethernet fragments (runt packets) when 5717 the link is in full duplex is an indication of an 5718 auto-negotiation or forced configuration mismatch" 5719 ::= { ptpTrapPrefix 5 } 5720 5721 auxPortStatusTrap NOTIFICATION-TYPE 5722 OBJECTS { auxPortStatus } 5723 STATUS current 5724 DESCRIPTION 5725 "Current status of the Aux Ethernet link. NB: a change of 5726 state may generate an SNMP trap and/or SMTP email alert" 5727 ::= { ptpTrapPrefix 6 } 5728 5729 auxPortDisabledWarningTrap NOTIFICATION-TYPE 5730 OBJECTS { auxPortDisabledWarning } 5731 STATUS current 5732 DESCRIPTION 5733 "The SNMP ifAdminStatus of the interface has disabled 5734 Ethernet traffic" 5735 ::= { ptpTrapPrefix 7 } 5736 5737 regulatoryBandTrap NOTIFICATION-TYPE 5738 OBJECTS { regulatoryBand } 5739 STATUS current 5740 DESCRIPTION 5741 "The Regulatory Band prohibits the wireless unit from 5742 operating outside the regulated limits. An invalid 5743 Regulatory Band may be caused by a missing or incorrect 5744 License Key, a corrupt MAC Address or an attempt to 5745 configure a Regulatory Band not allowed by the License 5746 Key. NB: a change of state may generate an SNMP trap 5747 and/or SMTP email alert." 5748 ::= { ptpTrapPrefix 8 } 5749 5750 installStatusTrap NOTIFICATION-TYPE 5751 OBJECTS { installStatus } 5752 STATUS current 5753 DESCRIPTION 5754 "A non-zero value indicates that signalling was received 5755 with the wrong MAC address or a mismatched link name. NB: 5756 It is very unusual to detect this, because units with 5757 mis-configured Target MAC Address will normally fail to 5758 establish a wireless link. However, rare circumstances 5759 may establish a partial wireless link and detect this 5760 situation. NB: A non-zero value on start-up, or a change 5761 of value during operation, may generate an SNMP trap 5762 and/or SMTP email alert" 5763 ::= { ptpTrapPrefix 9 } 5764 5765 installArmStateTrap NOTIFICATION-TYPE 5766 OBJECTS { installArmState } 5767 STATUS current 5768 DESCRIPTION 5769 "Indicates if the unit is being installed. NB: a change 5770 of state may generate an SNMP trap and/or SMTP email 5771 alert" 5772 ::= { ptpTrapPrefix 10 } 5773 5774 unitOutOfCalibrationTrap NOTIFICATION-TYPE 5775 OBJECTS { unitOutOfCalibration } 5776 STATUS current 5777 DESCRIPTION 5778 "The unit is out of calibration" 5779 ::= { ptpTrapPrefix 11 } 5780 5781 auxPortPowerOverEthernetOutputStatusTrap NOTIFICATION-TYPE 5782 OBJECTS { auxPortPowerOverEthernetOutputStatus } 5783 STATUS current 5784 DESCRIPTION 5785 "Current status of the Power Over Ethernet (PoE) output 5786 of the Aux port" 5787 ::= { ptpTrapPrefix 12 } 5788 5789 incompatibleRegulatoryBandsTrap NOTIFICATION-TYPE 5790 OBJECTS { incompatibleRegulatoryBands } 5791 STATUS current 5792 DESCRIPTION 5793 "The master and slave units have incompatible regulatory 5794 bands. NB: Both units must have compatible license keys" 5795 ::= { ptpTrapPrefix 14 } 5796 5797 noWirelessChannelAvailableTrap NOTIFICATION-TYPE 5798 OBJECTS { noWirelessChannelAvailable } 5799 STATUS current 5800 DESCRIPTION 5801 "Spectrum Management was unable to locate a suitable 5802 wireless channel to operate on" 5803 ::= { ptpTrapPrefix 15 } 5804 5805 wirelessLinkDisabledWarningTrap NOTIFICATION-TYPE 5806 OBJECTS { wirelessLinkDisabledWarning } 5807 STATUS current 5808 DESCRIPTION 5809 "The SNMP ifAdminStatus of the wireless interface has 5810 disabled wireless traffic" 5811 ::= { ptpTrapPrefix 16 } 5812 5813 auxPortConfigurationMismatchTrap NOTIFICATION-TYPE 5814 OBJECTS { auxPortConfigurationMismatch } 5815 STATUS current 5816 DESCRIPTION 5817 "The detection of Ethernet fragments (runt packets) when 5818 the link is in full duplex is an indication of an 5819 auto-negotiation or forced configuration mismatch. This 5820 alarm is only raised if an Out-of-Band Management Mode 5821 has been configured." 5822 ::= { ptpTrapPrefix 17 } 5823 5824 sFPErrorTrap NOTIFICATION-TYPE 5825 OBJECTS { sFPError } 5826 STATUS current 5827 DESCRIPTION 5828 "If the SFP link is not OK, there are five possible 5829 causes: Either a SFP has been installed but the license 5830 key does not include SFP fiber support, a fiber link 5831 could not be established even though no LOS was detected 5832 (i.e. an optical carrier was detected, which could be due 5833 to a broken TX fiber, or because the link is disabled at 5834 the fiber link partner), a fiber link could not be 5835 established and LOS is detected (i.e. no optical carrier 5836 is detected), the installed SFP is not supported or the 5837 installed SFP failed to initialize correctly. NB: a 5838 change of status may generate an SNMP trap and/or SMTP 5839 email alert" 5840 ::= { ptpTrapPrefix 18 } 5841 5842 sFPPortStatusTrap NOTIFICATION-TYPE 5843 OBJECTS { sFPPortStatus } 5844 STATUS current 5845 DESCRIPTION 5846 "Current status of the SFP Ethernet link. NB: a change of 5847 state may generate an SNMP trap and/or SMTP email alert" 5848 ::= { ptpTrapPrefix 19 } 5849 5850 incompatibleMasterAndSlaveTrap NOTIFICATION-TYPE 5851 OBJECTS { incompatibleMasterAndSlave } 5852 STATUS current 5853 DESCRIPTION 5854 "A non-zero value indicates that the master and slave 5855 ends of a link are different hardware products, or have 5856 different software versions. NB: It is very unusual to 5857 detect this, because incompatible units will normally 5858 fail to establish a wireless link. However, some 5859 combinations may establish a partial wireless link and 5860 detect this situation. NB: A non-zero value may generate 5861 an SNMP trap and/or SMTP email alert" 5862 ::= { ptpTrapPrefix 20 } 5863 5864 sNTPSyncTrap NOTIFICATION-TYPE 5865 OBJECTS { sNTPSync } 5866 STATUS current 5867 DESCRIPTION 5868 "If SNTP Sync fails then check the server settings in the 5869 Remote Management page, or disable SNTP" 5870 ::= { ptpTrapPrefix 21 } 5871 5872 tDDSynchronizationAlarmTrap NOTIFICATION-TYPE 5873 OBJECTS { tDDSynchronizationAlarm } 5874 STATUS current 5875 DESCRIPTION 5876 "Not Synchronized indicates failure of the external 5877 timing system for a period greater than the holdover 5878 timer. TDD frame timing will have drifted, and this link 5879 may cause interference with other links in a synchronized 5880 network. Timing System Failure is an early warning, 5881 indicating that 80% of the holdover period has expired." 5882 ::= { ptpTrapPrefix 22 } 5883 5884 sFPPortDisabledWarningTrap NOTIFICATION-TYPE 5885 OBJECTS { sFPPortDisabledWarning } 5886 STATUS current 5887 DESCRIPTION 5888 "The SNMP ifAdminStatus of the interface has disabled 5889 Ethernet traffic" 5890 ::= { ptpTrapPrefix 23 } 5891 5892 sFPPortConfigurationMismatchTrap NOTIFICATION-TYPE 5893 OBJECTS { sFPPortConfigurationMismatch } 5894 STATUS current 5895 DESCRIPTION 5896 "The detection of Ethernet fragments (runt packets) when 5897 the link is in full duplex is an indication of an 5898 auto-negotiation or forced configuration mismatch. This 5899 alarm is only raised if an Out-of-Band Management Mode 5900 has been configured." 5901 ::= { ptpTrapPrefix 24 } 5902 5903 linkModeOptimizationMismatchTrap NOTIFICATION-TYPE 5904 OBJECTS { linkModeOptimizationMismatch } 5905 STATUS current 5906 DESCRIPTION 5907 "The remote node of this link has been configured with a 5908 different link mode optimization" 5909 ::= { ptpTrapPrefix 25 } 5910 5911 tDMInterfaceStatusTrap NOTIFICATION-TYPE 5912 OBJECTS { tDMInterfaceStatus } 5913 STATUS current 5914 DESCRIPTION 5915 "@Current status of the connection to the TDM Box. A 5916 state of 'Up' on a green background indicates that the 5917 TDM Box is connected OK. When connecting a TDM Box only 5918 the Main Ethernet port should be used" 5919 ::= { ptpTrapPrefix 26 } 5920 5921 tDMChannelStatusTrap NOTIFICATION-TYPE 5922 OBJECTS { tDMChannelStatus } 5923 STATUS current 5924 DESCRIPTION 5925 "Current status of the TDM channels. A value of 0 5926 indicates that a TDM channel is established" 5927 ::= { ptpTrapPrefix 27 } 5928 5929 tDMChannelLoopbackTrap NOTIFICATION-TYPE 5930 OBJECTS { tDMChannelLoopback } 5931 STATUS current 5932 DESCRIPTION 5933 "The loopback status of TDM channels. This is intended 5934 for installation testing and should be set to 'None' for 5935 normal operation. The wire connections to a unit can be 5936 tested by applying a 'Copper' loopback to the local unit. 5937 The wireless connection to the remote unit can be tested 5938 by applying a 'Wireless' loopback to the remote unit with 5939 no loopback on the local unit. NB: a change of state may 5940 generate an SNMP trap and/or SMTP email alert" 5941 ::= { ptpTrapPrefix 28 } 5942 5943 nIDULanPortStatusTrap NOTIFICATION-TYPE 5944 OBJECTS { nIDULanPortStatus } 5945 STATUS current 5946 DESCRIPTION 5947 "Current status of the NIDU LAN Ethernet link. NB: a 5948 change of state may generate an SNMP trap and/or SMTP 5949 email alert" 5950 ::= { ptpTrapPrefix 29 } 5951 5952 syslogStateTrap NOTIFICATION-TYPE 5953 OBJECTS { syslogState } 5954 STATUS current 5955 DESCRIPTION 5956 "The syslog service has been enabled or disabled" 5957 ::= { ptpTrapPrefix 30 } 5958 5959 syslogLocalNearlyFullTrap NOTIFICATION-TYPE 5960 STATUS current 5961 DESCRIPTION "The syslog local log is nearly full (90%)" 5962 ::= { ptpTrapPrefix 31 } 5963 5964 syslogLocalWrappedTrap NOTIFICATION-TYPE 5965 STATUS current 5966 DESCRIPTION "The syslog local log has wrapped" 5967 ::= { ptpTrapPrefix 32 } 5968 5969 syslogClientTrap NOTIFICATION-TYPE 5970 OBJECTS { syslogClient } 5971 STATUS current 5972 DESCRIPTION 5973 "Enable or disable the syslog client" 5974 ::= { ptpTrapPrefix 33 } 5975 5976 secureModeAlarmTrap NOTIFICATION-TYPE 5977 OBJECTS { secureModeAlarm } 5978 STATUS current 5979 DESCRIPTION 5980 "The secure mode (e.g. FIPS, UC-APL) state of the unit. 5981 The secure mode is not configured(1) state indicates that 5982 the unit is capable of secure mode operation, and one or 5983 more of the following security materials has not been 5984 configured: Key Of Keys, Private Key, Public Certificate, 5985 DRNG Entropy Status, Wireless Encryption Key. The secure 5986 mode mode is configured but not active(2) state indicates 5987 that the unit is capable of secure mode operation, and 5988 the security material has been configured, but the 5989 configuration of interfaces is not consistent with secure 5990 mode operation. The secure mode is not supported(3) state 5991 indicates that the unit is not capable of secure mode 5992 operation. The secure mode capability requires 5993 appropriate hardware compatibility, license key and 5994 software image." 5995 ::= { ptpTrapPrefix 34 } 5996 5997 dataBridgingStatusAlarmTrap NOTIFICATION-TYPE 5998 OBJECTS { dataBridgingStatusAlarm } 5999 STATUS current 6000 DESCRIPTION 6001 "Ethernet Data traffic bridging is disabled because the 6002 wireless link is not operating at the configured Lowest 6003 Data Modulation Mode" 6004 ::= { ptpTrapPrefix 35 } 6005 6006 licenseRemainingTrialPeriodAlarmTrap NOTIFICATION-TYPE 6007 OBJECTS { licenseRemainingTrialPeriodAlarm } 6008 STATUS current 6009 DESCRIPTION 6010 "If the full capability trial license period is about to 6011 expire then purchase a license upgrade from your 6012 reseller." 6013 ::= { ptpTrapPrefix 36 } 6014 6015 capacityVariantMismatchTrap NOTIFICATION-TYPE 6016 OBJECTS { capacityVariantMismatch } 6017 STATUS current 6018 DESCRIPTION 6019 "The remote node of this link has a lower link capacity. 6020 Operating with a reduced effective link capacity." 6021 ::= { ptpTrapPrefix 37 } 6022 6023 maxLinkRangeExceededTrap NOTIFICATION-TYPE 6024 OBJECTS { maxLinkRangeExceeded } 6025 STATUS current 6026 DESCRIPTION 6027 "The measured link range is greater than the maximum 6028 allowed by the license key. The link will operate at a 6029 reduced capacity while this condition applies. This alarm 6030 is only raised if the license specifies a maximum link 6031 range and the trial license is not active." 6032 ::= { ptpTrapPrefix 38 } 6033 6034 tDMConfigurationMismatchTrap NOTIFICATION-TYPE 6035 OBJECTS { tDMConfigurationMismatch } 6036 STATUS current 6037 DESCRIPTION 6038 "Current status of the configuration of the TDM Box. A 6039 state of 'Ok' on a green background indicates that the 6040 TDM Box configuration is matched OK with the remote end." 6041 ::= { ptpTrapPrefix 39 } 6042 6043 nIDULanPortDisabledWarningTrap NOTIFICATION-TYPE 6044 OBJECTS { nIDULanPortDisabledWarning } 6045 STATUS current 6046 DESCRIPTION 6047 "The SNMP ifAdminStatus of the interface has disabled 6048 Ethernet traffic" 6049 ::= { ptpTrapPrefix 40 } 6050 6051 nIDULanPortConfigurationMismatchTrap NOTIFICATION-TYPE 6052 OBJECTS { nIDULanPortConfigurationMismatch } 6053 STATUS current 6054 DESCRIPTION 6055 "The detection of Ethernet fragments (runt packets) when 6056 the link is in full duplex is an indication of an 6057 auto-negotiation or forced configuration mismatch." 6058 ::= { ptpTrapPrefix 41 } 6059 6060 secondDataBridgingStatusAlarmTrap NOTIFICATION-TYPE 6061 OBJECTS { secondDataBridgingStatusAlarm } 6062 STATUS current 6063 DESCRIPTION 6064 "Bridging of Ethernet traffic from Second Data Service 6065 has been disabled because the wireless link is not 6066 operating at the configured Lowest Second Data Modulation 6067 Mode" 6068 ::= { ptpTrapPrefix 42 } 6069 6070 transparentClockSourcePortAlarmTrap NOTIFICATION-TYPE 6071 OBJECTS { transparentClockSourcePortAlarm } 6072 STATUS current 6073 DESCRIPTION 6074 "Transparent Clock will not function properly because 6075 SFP, the selected clock source port is not FIBER" 6076 ::= { ptpTrapPrefix 43 } 6077 6078 portAllocationMismatchTrap NOTIFICATION-TYPE 6079 OBJECTS { portAllocationMismatch } 6080 STATUS current 6081 DESCRIPTION 6082 "The local and remote ODUs have different services 6083 configured." 6084 ::= { ptpTrapPrefix 44 } 6085 6086 END 6087