1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2// Copyright (C) 2016 ARM Ltd.
3// Copyright (C) 2018 Hauke Mehrtens <hauke@hauke-m.de>
4
5/dts-v1/;
6#include "sun50i-h5.dtsi"
7
8#include <dt-bindings/gpio/gpio.h>
9#include <dt-bindings/input/input.h>
10#include <dt-bindings/pinctrl/sun4i-a10.h>
11
12/ {
13	model = "Xunlong Orange Pi Zero Plus";
14	compatible = "xunlong,orangepi-zero-plus", "allwinner,sun50i-h5";
15
16	reg_vcc3v3: vcc3v3 {
17		compatible = "regulator-fixed";
18		regulator-name = "vcc3v3";
19		regulator-min-microvolt = <3300000>;
20		regulator-max-microvolt = <3300000>;
21	};
22
23	aliases {
24		ethernet0 = &emac;
25		ethernet1 = &rtl8189ftv;
26		serial0 = &uart0;
27	};
28
29	chosen {
30		stdout-path = "serial0:115200n8";
31	};
32
33	leds {
34		compatible = "gpio-leds";
35
36		pwr {
37			label = "orangepi:green:pwr";
38			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
39			default-state = "on";
40		};
41
42		status {
43			label = "orangepi:red:status";
44			gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
45		};
46	};
47
48	reg_gmac_3v3: gmac-3v3 {
49		compatible = "regulator-fixed";
50		regulator-name = "gmac-3v3";
51		regulator-min-microvolt = <3300000>;
52		regulator-max-microvolt = <3300000>;
53		startup-delay-us = <100000>;
54		enable-active-high;
55		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
56	};
57};
58
59&ehci0 {
60	status = "okay";
61};
62
63&ehci1 {
64	status = "okay";
65};
66
67&emac {
68	pinctrl-names = "default";
69	pinctrl-0 = <&emac_rgmii_pins>;
70	phy-supply = <&reg_gmac_3v3>;
71	phy-handle = <&ext_rgmii_phy>;
72	phy-mode = "rgmii";
73	status = "okay";
74};
75
76&external_mdio {
77	ext_rgmii_phy: ethernet-phy@1 {
78		compatible = "ethernet-phy-ieee802.3-c22";
79		reg = <1>;
80	};
81};
82
83&mmc0 {
84	vmmc-supply = <&reg_vcc3v3>;
85	bus-width = <4>;
86	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
87	status = "okay";
88};
89
90&mmc1 {
91	vmmc-supply = <&reg_vcc3v3>;
92	bus-width = <4>;
93	non-removable;
94	status = "okay";
95
96	/*
97	 * Explicitly define the sdio device, so that we can add an ethernet
98	 * alias for it (which e.g. makes u-boot set a mac-address).
99	 */
100	rtl8189ftv: sdio_wifi@1 {
101		reg = <1>;
102	};
103};
104
105&spi0  {
106	status = "okay";
107
108	flash@0 {
109		#address-cells = <1>;
110		#size-cells = <1>;
111		compatible = "mxicy,mx25l1606e", "winbond,w25q128";
112		reg = <0>;
113		spi-max-frequency = <40000000>;
114	};
115};
116
117&ohci0 {
118	status = "okay";
119};
120
121&ohci1 {
122	status = "okay";
123};
124
125&uart0 {
126	pinctrl-names = "default";
127	pinctrl-0 = <&uart0_pa_pins>;
128	status = "okay";
129};
130
131&usb_otg {
132	dr_mode = "peripheral";
133	status = "okay";
134};
135
136&usbphy {
137	/* USB Type-A ports' VBUS is always on */
138	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
139	status = "okay";
140};
141