1 /* SPDX-License-Identifier: GPL-2.0 */
2 /*
3  * Copyright (C) 2018 Cadence Design Systems Inc.
4  */
5 
6 #ifndef __PHY_MIPI_DPHY_H_
7 #define __PHY_MIPI_DPHY_H_
8 
9 /**
10  * struct phy_configure_opts_mipi_dphy - MIPI D-PHY configuration set
11  *
12  * This structure is used to represent the configuration state of a
13  * MIPI D-PHY phy.
14  */
15 struct phy_configure_opts_mipi_dphy {
16 	/**
17 	 * @clk_miss:
18 	 *
19 	 * Timeout, in picoseconds, for receiver to detect absence of
20 	 * Clock transitions and disable the Clock Lane HS-RX.
21 	 *
22 	 * Maximum value: 60000 ps
23 	 */
24 	unsigned int		clk_miss;
25 
26 	/**
27 	 * @clk_post:
28 	 *
29 	 * Time, in picoseconds, that the transmitter continues to
30 	 * send HS clock after the last associated Data Lane has
31 	 * transitioned to LP Mode. Interval is defined as the period
32 	 * from the end of @hs_trail to the beginning of @clk_trail.
33 	 *
34 	 * Minimum value: 60000 ps + 52 * @hs_clk_rate period in ps
35 	 */
36 	unsigned int		clk_post;
37 
38 	/**
39 	 * @clk_pre:
40 	 *
41 	 * Time, in UI, that the HS clock shall be driven by
42 	 * the transmitter prior to any associated Data Lane beginning
43 	 * the transition from LP to HS mode.
44 	 *
45 	 * Minimum value: 8 UI
46 	 */
47 	unsigned int		clk_pre;
48 
49 	/**
50 	 * @clk_prepare:
51 	 *
52 	 * Time, in picoseconds, that the transmitter drives the Clock
53 	 * Lane LP-00 Line state immediately before the HS-0 Line
54 	 * state starting the HS transmission.
55 	 *
56 	 * Minimum value: 38000 ps
57 	 * Maximum value: 95000 ps
58 	 */
59 	unsigned int		clk_prepare;
60 
61 	/**
62 	 * @clk_settle:
63 	 *
64 	 * Time interval, in picoseconds, during which the HS receiver
65 	 * should ignore any Clock Lane HS transitions, starting from
66 	 * the beginning of @clk_prepare.
67 	 *
68 	 * Minimum value: 95000 ps
69 	 * Maximum value: 300000 ps
70 	 */
71 	unsigned int		clk_settle;
72 
73 	/**
74 	 * @clk_term_en:
75 	 *
76 	 * Time, in picoseconds, for the Clock Lane receiver to enable
77 	 * the HS line termination.
78 	 *
79 	 * Maximum value: 38000 ps
80 	 */
81 	unsigned int		clk_term_en;
82 
83 	/**
84 	 * @clk_trail:
85 	 *
86 	 * Time, in picoseconds, that the transmitter drives the HS-0
87 	 * state after the last payload clock bit of a HS transmission
88 	 * burst.
89 	 *
90 	 * Minimum value: 60000 ps
91 	 */
92 	unsigned int		clk_trail;
93 
94 	/**
95 	 * @clk_zero:
96 	 *
97 	 * Time, in picoseconds, that the transmitter drives the HS-0
98 	 * state prior to starting the Clock.
99 	 */
100 	unsigned int		clk_zero;
101 
102 	/**
103 	 * @d_term_en:
104 	 *
105 	 * Time, in picoseconds, for the Data Lane receiver to enable
106 	 * the HS line termination.
107 	 *
108 	 * Maximum value: 35000 ps + 4 * @hs_clk_rate period in ps
109 	 */
110 	unsigned int		d_term_en;
111 
112 	/**
113 	 * @eot:
114 	 *
115 	 * Transmitted time interval, in picoseconds, from the start
116 	 * of @hs_trail or @clk_trail, to the start of the LP- 11
117 	 * state following a HS burst.
118 	 *
119 	 * Maximum value: 105000 ps + 12 * @hs_clk_rate period in ps
120 	 */
121 	unsigned int		eot;
122 
123 	/**
124 	 * @hs_exit:
125 	 *
126 	 * Time, in picoseconds, that the transmitter drives LP-11
127 	 * following a HS burst.
128 	 *
129 	 * Minimum value: 100000 ps
130 	 */
131 	unsigned int		hs_exit;
132 
133 	/**
134 	 * @hs_prepare:
135 	 *
136 	 * Time, in picoseconds, that the transmitter drives the Data
137 	 * Lane LP-00 Line state immediately before the HS-0 Line
138 	 * state starting the HS transmission.
139 	 *
140 	 * Minimum value: 40000 ps + 4 * @hs_clk_rate period in ps
141 	 * Maximum value: 85000 ps + 6 * @hs_clk_rate period in ps
142 	 */
143 	unsigned int		hs_prepare;
144 
145 	/**
146 	 * @hs_settle:
147 	 *
148 	 * Time interval, in picoseconds, during which the HS receiver
149 	 * shall ignore any Data Lane HS transitions, starting from
150 	 * the beginning of @hs_prepare.
151 	 *
152 	 * Minimum value: 85000 ps + 6 * @hs_clk_rate period in ps
153 	 * Maximum value: 145000 ps + 10 * @hs_clk_rate period in ps
154 	 */
155 	unsigned int		hs_settle;
156 
157 	/**
158 	 * @hs_skip:
159 	 *
160 	 * Time interval, in picoseconds, during which the HS-RX
161 	 * should ignore any transitions on the Data Lane, following a
162 	 * HS burst. The end point of the interval is defined as the
163 	 * beginning of the LP-11 state following the HS burst.
164 	 *
165 	 * Minimum value: 40000 ps
166 	 * Maximum value: 55000 ps + 4 * @hs_clk_rate period in ps
167 	 */
168 	unsigned int		hs_skip;
169 
170 	/**
171 	 * @hs_trail:
172 	 *
173 	 * Time, in picoseconds, that the transmitter drives the
174 	 * flipped differential state after last payload data bit of a
175 	 * HS transmission burst
176 	 *
177 	 * Minimum value: max(8 * @hs_clk_rate period in ps,
178 	 *		      60000 ps + 4 * @hs_clk_rate period in ps)
179 	 */
180 	unsigned int		hs_trail;
181 
182 	/**
183 	 * @hs_zero:
184 	 *
185 	 * Time, in picoseconds, that the transmitter drives the HS-0
186 	 * state prior to transmitting the Sync sequence.
187 	 */
188 	unsigned int		hs_zero;
189 
190 	/**
191 	 * @init:
192 	 *
193 	 * Time, in microseconds for the initialization period to
194 	 * complete.
195 	 *
196 	 * Minimum value: 100 us
197 	 */
198 	unsigned int		init;
199 
200 	/**
201 	 * @lpx:
202 	 *
203 	 * Transmitted length, in picoseconds, of any Low-Power state
204 	 * period.
205 	 *
206 	 * Minimum value: 50000 ps
207 	 */
208 	unsigned int		lpx;
209 
210 	/**
211 	 * @ta_get:
212 	 *
213 	 * Time, in picoseconds, that the new transmitter drives the
214 	 * Bridge state (LP-00) after accepting control during a Link
215 	 * Turnaround.
216 	 *
217 	 * Value: 5 * @lpx
218 	 */
219 	unsigned int		ta_get;
220 
221 	/**
222 	 * @ta_go:
223 	 *
224 	 * Time, in picoseconds, that the transmitter drives the
225 	 * Bridge state (LP-00) before releasing control during a Link
226 	 * Turnaround.
227 	 *
228 	 * Value: 4 * @lpx
229 	 */
230 	unsigned int		ta_go;
231 
232 	/**
233 	 * @ta_sure:
234 	 *
235 	 * Time, in picoseconds, that the new transmitter waits after
236 	 * the LP-10 state before transmitting the Bridge state
237 	 * (LP-00) during a Link Turnaround.
238 	 *
239 	 * Minimum value: @lpx
240 	 * Maximum value: 2 * @lpx
241 	 */
242 	unsigned int		ta_sure;
243 
244 	/**
245 	 * @wakeup:
246 	 *
247 	 * Time, in microseconds, that a transmitter drives a Mark-1
248 	 * state prior to a Stop state in order to initiate an exit
249 	 * from ULPS.
250 	 *
251 	 * Minimum value: 1000 us
252 	 */
253 	unsigned int		wakeup;
254 
255 	/**
256 	 * @hs_clk_rate:
257 	 *
258 	 * Clock rate, in Hertz, of the high-speed clock.
259 	 */
260 	unsigned long		hs_clk_rate;
261 
262 	/**
263 	 * @lp_clk_rate:
264 	 *
265 	 * Clock rate, in Hertz, of the low-power clock.
266 	 */
267 	unsigned long		lp_clk_rate;
268 
269 	/**
270 	 * @lanes:
271 	 *
272 	 * Number of active, consecutive, data lanes, starting from
273 	 * lane 0, used for the transmissions.
274 	 */
275 	unsigned char		lanes;
276 };
277 
278 int phy_mipi_dphy_get_default_config(unsigned long pixel_clock,
279 				     unsigned int bpp,
280 				     unsigned int lanes,
281 				     struct phy_configure_opts_mipi_dphy *cfg);
282 int phy_mipi_dphy_config_validate(struct phy_configure_opts_mipi_dphy *cfg);
283 
284 #endif /* __PHY_MIPI_DPHY_H_ */
285