1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2014 Soeren Moch <smoch@web.de> 4 * 5 * Configuration settings for the TBS2910 MatrixARM board. 6 */ 7 8 #ifndef __TBS2910_CONFIG_H 9 #define __TBS2910_CONFIG_H 10 11 #include "mx6_common.h" 12 13 /* General configuration */ 14 15 #define CONFIG_MACH_TYPE 3980 16 17 #define CONFIG_SYS_HZ 1000 18 19 /* Physical Memory Map */ 20 #define CONFIG_SYS_SDRAM_BASE MMDC0_ARB_BASE_ADDR 21 22 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 23 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 24 #define CONFIG_SYS_INIT_SP_OFFSET \ 25 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 26 #define CONFIG_SYS_INIT_SP_ADDR \ 27 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 28 29 #define CONFIG_SYS_MALLOC_LEN (128 * 1024 * 1024) 30 31 #define CONFIG_SYS_BOOTMAPSZ 0x10000000 32 33 /* Serial console */ 34 #define CONFIG_MXC_UART_BASE UART1_BASE /* select UART1/UART2 */ 35 36 /* Framebuffer */ 37 #define CONFIG_IMX_HDMI 38 #define CONFIG_IMX_VIDEO_SKIP 39 40 /* PCI */ 41 #ifdef CONFIG_CMD_PCI 42 #define CONFIG_PCI_SCAN_SHOW 43 #define CONFIG_PCIE_IMX 44 #define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) 45 #endif 46 47 /* SATA */ 48 #ifdef CONFIG_CMD_SATA 49 #define CONFIG_SYS_SATA_MAX_DEVICE 1 50 #define CONFIG_DWC_AHSATA_PORT_ID 0 51 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR 52 #define CONFIG_LBA48 53 #define CONFIG_SYS_64BIT_LBA 54 #endif 55 56 /* USB */ 57 #ifdef CONFIG_CMD_USB 58 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 59 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 60 #ifdef CONFIG_CMD_USB_MASS_STORAGE 61 #define CONFIG_USBD_HS 62 #endif /* CONFIG_CMD_USB_MASS_STORAGE */ 63 #endif /* CONFIG_CMD_USB */ 64 65 #define CONFIG_BOARD_SIZE_LIMIT 392192 /* (CONFIG_ENV_OFFSET - 1024) */ 66 67 #define CONFIG_EXTRA_ENV_SETTINGS \ 68 BOOTENV \ 69 "bootargs_mmc1=console=ttymxc0,115200 di0_primary console=tty1\0" \ 70 "bootargs_mmc2=video=mxcfb0:dev=hdmi,1920x1080M@60 " \ 71 "video=mxcfb1:off video=mxcfb2:off fbmem=28M\0" \ 72 "bootargs_mmc3=root=/dev/mmcblk0p1 rootwait consoleblank=0 quiet\0" \ 73 "bootargs_mmc=setenv bootargs ${bootargs_mmc1} ${bootargs_mmc2} " \ 74 "${bootargs_mmc3}\0" \ 75 "bootargs_upd=setenv bootargs console=ttymxc0,115200 " \ 76 "rdinit=/sbin/init enable_wait_mode=off\0" \ 77 "bootcmd_mmc=run bootargs_mmc; mmc dev 2; " \ 78 "mmc read 0x10800000 0x800 0x4000; bootm 0x10800000\0" \ 79 "bootcmd_up1=load mmc 1 0x10800000 uImage\0" \ 80 "bootcmd_up2=load mmc 1 0x10d00000 uramdisk.img; " \ 81 "run bootargs_upd; " \ 82 "bootm 0x10800000 0x10d00000\0" \ 83 "console=ttymxc0\0" \ 84 "fan=gpio set 92\0" \ 85 "fdt_addr_r=0x18000000\0" \ 86 "fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \ 87 "kernel_addr_r=0x12000000\0" \ 88 "pxefile_addr_r=0x10100000\0" \ 89 "ramdisk_addr_r=0x18080000\0" \ 90 "scriptaddr=0x10000000\0" \ 91 "set_con_serial=setenv stdout serial; " \ 92 "setenv stderr serial\0" \ 93 "set_con_hdmi=setenv stdout serial,vidconsole; " \ 94 "setenv stderr serial,vidconsole\0" \ 95 "stderr=serial,vidconsole\0" \ 96 "stdin=serial,usbkbd\0" \ 97 "stdout=serial,vidconsole\0" 98 99 /* Enable distro boot */ 100 #define BOOT_TARGET_DEVICES(func) \ 101 func(MMC, mmc, 0) \ 102 func(MMC, mmc, 1) \ 103 func(MMC, mmc, 2) \ 104 func(SATA, sata, 0) \ 105 func(USB, usb, 0) 106 107 #include <config_distro_bootcmd.h> 108 109 #endif /* __TBS2910_CONFIG_H * */ 110