1.\" 2.\" Copyright (c) 2000 Michael Smith 3.\" Copyright (c) 2000 BSDi 4.\" All rights reserved. 5.\" 6.\" Redistribution and use in source and binary forms, with or without 7.\" modification, are permitted provided that the following conditions 8.\" are met: 9.\" 1. Redistributions of source code must retain the above copyright 10.\" notice, this list of conditions and the following disclaimer. 11.\" 2. The name of the author may not be used to endorse or promote products 12.\" derived from this software without specific prior written permission 13.\" 14.\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 15.\" IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 16.\" OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 17.\" IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 18.\" INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 19.\" NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 20.\" DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 21.\" THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 22.\" (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 23.\" THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 24.\" 25.\" $FreeBSD: src/share/man/man4/mly.4,v 1.4.2.3 2001/07/21 09:16:46 schweikh Exp $ 26.\" $DragonFly: src/share/man/man4/mly.4,v 1.3 2006/02/17 19:37:09 swildner Exp $ 27.\" 28.Dd August 22, 2000 29.Dt MLY 4 30.Os 31.Sh NAME 32.Nm mly 33.Nd Mylex AcceleRAID/eXtremeRAID family driver 34.Sh SYNOPSIS 35.Cd device pci 36.Cd device mly 37.Cd device scbus 38.Cd device da 39.Sh DESCRIPTION 40The 41.Nm 42driver provides support for Mylex AcceleRAID and eXtremeRAID-family 43PCI to SCSI RAID controllers with version 6.00 and later 44firmware. 45Supported controllers include: 46.Bl -bullet 47.It 48AcceleRAID 160 49.It 50AcceleRAID 170 51.It 52AcceleRAID 352 53.It 54eXtremeRAID 2000 55.It 56eXtremeRAID 3000 57.El 58.Pp 59Compatible Mylex controllers not listed should work, but have not been 60verified. 61.Pp 62Logical devices (array drives) attached to the controller are presented 63to the SCSI subsystem as though they were direct-access devices on a 64virtual SCSI bus. 65Physical devices which are not claimed by a logical 66device are presented on SCSI channels which match the physical channels 67on the controller. 68.Sh DIAGNOSTICS 69.Ss Controller initialisation phase 70.Bl -diag 71.It "mly%d: controller initialisation started" 72.It "mly%d: initialisation complete" 73.Pp 74The controller firmware has started initialisation. 75Normally this process is performed by the controller BIOS, 76but the driver may need 77to do this in cases where the BIOS has failed, or is not compatible 78(e.g. on non-x86 systems). 79.It "mly%d: drive spinup in progress" 80.Pp 81Drive startup is in progress; this may take several minutes. 82.It "mly%d: mirror race recovery failed, one or more drives offline" 83.It "mly%d: mirror race recovery in progress" 84.It "mly%d: mirror race recovery on a critical drive" 85.Pp 86These error codes are undocumented. 87.It "mly%d: FATAL MEMORY PARITY ERROR" 88.Pp 89Firmware detected a fatal memory error; the driver will not attempt to 90attach to this controller. 91.It "mly%d: unknown initialisation code %x" 92.Pp 93An unknown error occurred during initialisation; it will be ignored. 94.El 95.Ss Driver initialisation/shutdown phase 96.Bl -diag 97.It "mly%d: can't enable busmaster feature" 98.It "mly%d: memory window not available" 99.It "mly%d: can't allocate register window" 100.It "mly%d: can't allocate interrupt" 101.It "mly%d: can't set up interrupt" 102.Pp 103The system's PCI BIOS has not correctly configured the controller's 104PCI interface; initialisation has failed and the driver will not 105attach to this controller. 106.It "mly%d: can't allocate parent DMA tag" 107.It "mly%d: can't allocate buffer DMA tag" 108.It "mly%d: can't allocate command packet DMA tag" 109.It "mly%d: can't allocate scatter/gather DMA tag" 110.It "mly%d: can't allocate s/g table" 111.It "mly%d: can't allocate memory mailbox DMA tag" 112.It "mly%d: can't allocate memory mailbox" 113.Pp 114A resource allocation error occurred while initialising the driver; 115initialisation has failed and the driver will not attach to this 116controller. 117.It "mly%d: BTL rescan result corrupted" 118.Pp 119The results of a scan for an attached device were corrupted. 120One or more devices may not be correctly reported. 121.It "mly%d: flushing cache..." 122.Pp 123The controller cache is being flushed prior to detach or shutdown. 124.El 125.Ss Operational diagnostics 126.Bl -diag 127.It "mly%d: physical device %d:%d online" 128.It "mly%d: physical device %d:%d standby" 129.It "mly%d: physical device %d:%d automatic rebuild started" 130.It "mly%d: physical device %d:%d manual rebuild started" 131.It "mly%d: physical device %d:%d rebuild completed" 132.It "mly%d: physical device %d:%d rebuild cancelled" 133.It "mly%d: physical device %d:%d rebuild failed for unknown reasons" 134.It "mly%d: physical device %d:%d rebuild failed due to new physical device" 135.It "mly%d: physical device %d:%d rebuild failed due to logical drive failure" 136.It "mly%d: physical device %d:%d found" 137.It "mly%d: physical device %d:%d gone" 138.It "mly%d: physical device %d:%d unconfigured" 139.It "mly%d: physical device %d:%d expand capacity started" 140.It "mly%d: physical device %d:%d expand capacity completed" 141.It "mly%d: physical device %d:%d expand capacity failed" 142.It "mly%d: physical device %d:%d parity error" 143.It "mly%d: physical device %d:%d soft error" 144.It "mly%d: physical device %d:%d miscellaneous error" 145.It "mly%d: physical device %d:%d reset" 146.It "mly%d: physical device %d:%d active spare found" 147.It "mly%d: physical device %d:%d warm spare found" 148.It "mly%d: physical device %d:%d initialization started" 149.It "mly%d: physical device %d:%d initialization completed" 150.It "mly%d: physical device %d:%d initialization failed" 151.It "mly%d: physical device %d:%d initialization cancelled" 152.It "mly%d: physical device %d:%d write recovery failed" 153.It "mly%d: physical device %d:%d scsi bus reset failed" 154.It "mly%d: physical device %d:%d double check condition" 155.It "mly%d: physical device %d:%d device cannot be accessed" 156.It "mly%d: physical device %d:%d gross error on scsi processor" 157.It "mly%d: physical device %d:%d bad tag from device" 158.It "mly%d: physical device %d:%d command timeout" 159.It "mly%d: physical device %d:%d system reset" 160.It "mly%d: physical device %d:%d busy status or parity error" 161.It "mly%d: physical device %d:%d host set device to failed state" 162.It "mly%d: physical device %d:%d selection timeout" 163.It "mly%d: physical device %d:%d scsi bus phase error" 164.It "mly%d: physical device %d:%d device returned unknown status" 165.It "mly%d: physical device %d:%d device not ready" 166.It "mly%d: physical device %d:%d device not found at startup" 167.It "mly%d: physical device %d:%d COD write operation failed" 168.It "mly%d: physical device %d:%d BDT write operation failed" 169.It "mly%d: physical device %d:%d missing at startup" 170.It "mly%d: physical device %d:%d start rebuild failed due to physical drive too small" 171.It "mly%d: physical device %d:%d sense data received" 172.It "mly%d: sense key %d asc %02x ascq %02x" 173.It "mly%d: info %4D csi %4D" 174.It "mly%d: physical device %d:%d offline" 175.It "mly%d: sense key %d asc %02x ascq %02x" 176.It "mly%d: info %4D csi %4D" 177.Pp 178The reported event refers to the physical device at the given channel:target 179address. 180.It "mly%d: logical device %d (%s) consistency check started" 181.It "mly%d: logical device %d (%s) consistency check completed" 182.It "mly%d: logical device %d (%s) consistency check cancelled" 183.It "mly%d: logical device %d (%s) consistency check completed with errors" 184.It "mly%d: logical device %d (%s) consistency check failed due to logical drive failure" 185.It "mly%d: logical device %d (%s) consistency check failed due to physical device failure" 186.It "mly%d: logical device %d (%s) automatic rebuild started" 187.It "mly%d: logical device %d (%s) manual rebuild started" 188.It "mly%d: logical device %d (%s) rebuild completed" 189.It "mly%d: logical device %d (%s) rebuild cancelled" 190.It "mly%d: logical device %d (%s) rebuild failed for unknown reasons" 191.It "mly%d: logical device %d (%s) rebuild failed due to new physical device" 192.It "mly%d: logical device %d (%s) rebuild failed due to logical drive failure" 193.It "mly%d: logical device %d (%s) offline" 194.It "mly%d: logical device %d (%s) critical" 195.It "mly%d: logical device %d (%s) online" 196.It "mly%d: logical device %d (%s) initialization started" 197.It "mly%d: logical device %d (%s) initialization completed" 198.It "mly%d: logical device %d (%s) initialization cancelled" 199.It "mly%d: logical device %d (%s) initialization failed" 200.It "mly%d: logical device %d (%s) found" 201.It "mly%d: logical device %d (%s) gone" 202.It "mly%d: logical device %d (%s) expand capacity started" 203.It "mly%d: logical device %d (%s) expand capacity completed" 204.It "mly%d: logical device %d (%s) expand capacity failed" 205.It "mly%d: logical device %d (%s) bad block found" 206.It "mly%d: logical device %d (%s) size changed" 207.It "mly%d: logical device %d (%s) type changed" 208.It "mly%d: logical device %d (%s) bad data block found" 209.It "mly%d: logical device %d (%s) read of data block in bdt" 210.It "mly%d: logical device %d (%s) write back data for disk block lost" 211.Pp 212The event report will include the name of the SCSI device which has 213attached to the device if possible. 214.It "mly%d: enclosure %d fan %d failed" 215.It "mly%d: enclosure %d fan %d ok" 216.It "mly%d: enclosure %d fan %d not present" 217.It "mly%d: enclosure %d power supply %d failed" 218.It "mly%d: enclosure %d power supply %d ok" 219.It "mly%d: enclosure %d power supply %d not present" 220.It "mly%d: enclosure %d temperature sensor %d failed" 221.It "mly%d: enclosure %d temperature sensor %d critical" 222.It "mly%d: enclosure %d temperature sensor %d ok" 223.It "mly%d: enclosure %d temperature sensor %d not present" 224.It "mly%d: enclosure %d unit %d access critical" 225.It "mly%d: enclosure %d unit %d access ok" 226.It "mly%d: enclosure %d unit %d access offline" 227.Pp 228These events refer to external enclosures by number. 229The driver does not attempt to name the enclosures. 230.It "mly%d: controller cache write back error" 231.It "mly%d: controller battery backup unit found" 232.It "mly%d: controller battery backup unit charge level low" 233.It "mly%d: controller battery backup unit charge level ok" 234.It "mly%d: controller installation aborted" 235.It "mly%d: controller mirror race recovery in progress" 236.It "mly%d: controller mirror race on critical drive" 237.It "mly%d: controller memory soft ecc error" 238.It "mly%d: controller memory hard ecc error" 239.It "mly%d: controller battery backup unit failed" 240.Pp 241These events report controller status changes. 242.El 243.Sh AUTHORS 244.An -nosplit 245The 246.Nm 247driver was written by 248.An Michael Smith 249.Aq msmith@FreeBSD.org . 250.Pp 251This manual page was written by 252.An Michael Smith 253.Aq msmith@FreeBSD.org . 254.Sh BUGS 255The driver does not yet provide an external management interface. 256.Pp 257Enclosures are not named or otherwise identified in event messages. 258