man/man4/ppbus.4

.\" Copyright (c) 1998, 1999 Nicolas Souchu
.\" All rights reserved.
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\"    notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\"    notice, this list of conditions and the following disclaimer in the
.\"    documentation and/or other materials provided with the distribution.
.\"
.\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
.\" ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
.\" SUCH DAMAGE.
.\"
.\" $FreeBSD: src/share/man/man4/ppbus.4,v 1.14.2.5 2001/08/17 13:08:39 ru Exp $
.\"
.Dd March 1, 1998
.Dt PPBUS 4
.Os
.Sh NAME
.Nm ppbus
.Nd Parallel Port Bus system
.Sh SYNOPSIS
.Cd "device ppbus"
.Cd "options DEBUG_1284"
.Pp
.Cd "device vpo"
.Pp
.Cd "device lpt"
.Cd "device plip"
.Cd "device ppi"
.Cd "device pps"
.Cd "device lpbb"
.Sh DESCRIPTION
The
.Em ppbus
system provides a uniform, modular and architecture-independent
system for the implementation of drivers to control various parallel devices,
and to utilize different parallel port chipsets.
.Sh DEVICE DRIVERS
In order to write new drivers or port existing drivers, the ppbus system
provides the following facilities:
.Bl -bullet -offset indent
.It
architecture-independent macros or functions to access parallel ports
.It
mechanism to allow various devices to share the same parallel port
.It
a user interface named
.Xr ppi 4
that allows parallel port access from outside the kernel without conflicting
with kernel-in drivers.
.El
.Ss Developing new drivers
The ppbus system has been designed to support the development of standard
and non-standard software:
.Pp
.Bl -column "Driver" -compact
.It Em Driver Ta Em Description
.It Sy vpo Ta "VPI0 parallel to Adaptec AIC-7110 SCSI controller driver" .
It uses standard and non-standard parallel port accesses.
.It Sy ppi Ta "Parallel port interface for general I/O"
.It Sy pps Ta "Pulse per second Timing Interface"
.It Sy lpbb Ta "Philips official parallel port I2C bit-banging interface"
.El
.Ss Porting existing drivers
Another approach to the ppbus system is to port existing drivers.
Various drivers have already been ported:
.Pp
.Bl -column "Driver" -compact
.It Em Driver Ta Em Description
.It Sy lpt Ta "lpt printer driver"
.It Sy plip Ta "lp parallel network interface driver"
.El
.Pp
ppbus should let you port any other software even from other operating systems
that provide similar services.
.Sh PARALLEL PORT CHIPSETS
Parallel port chipset support is provided by
.Xr ppc 4 .
.Pp
The ppbus system provides functions and macros to allocate a new
parallel port bus, then initialize it and upper peripheral device drivers.
.Pp
ppc makes chipset detection and initialization and then calls ppbus attach
functions to initialize the ppbus system.
.Sh PARALLEL PORT MODEL
The logical parallel port model chosen for the ppbus system is the PC's
parallel port model.
Consequently, most of the services provided by ppc are macros for
.Fn inb
and
.Fn outb
calls.
But, for another architecture, accesses to one of our logical
registers (data, status, control...) may require more than one I/O access.
.Ss Description
The parallel port may operate in the following modes:
.Bl -bullet -offset indent
.It
compatible mode, also called Centronics mode
.It
bidirectional 8/4-bits mode, also called NIBBLE mode
.It
byte mode, also called PS/2 mode
.It
Extended Capability Port mode, ECP
.It
Enhanced Parallel Port mode, EPP
.It
mixed ECP+EPP or ECP+PS/2 modes
.El
.Ss Compatible mode
This mode defines the protocol used by most PCs to transfer data to a printer.
In this mode, data is placed on the port's data lines, the printer status is
checked for no errors and that it is not busy, and then a data Strobe is
generated by the software to clock the data to the printer.
.Pp
Many I/O controllers have implemented a mode that uses a FIFO buffer to
transfer data with the Compatibility mode protocol.
This mode is referred to as
"Fast Centronics" or "Parallel Port FIFO mode".
.Ss Bidirectional mode
The NIBBLE mode is the most common way to get reverse channel data from a
printer or peripheral.
Combined with the standard host to printer mode, it
provides a complete bidirectional channel.
.Pp
In this mode, outputs are 8-bits long.
Inputs are accomplished by reading
4 of the 8 bits of the status register.
.Ss Byte mode
In this mode, the data register is used either for outputs and inputs.
Then,
any transfer is 8-bits long.
.Ss Extended Capability Port mode
The ECP protocol was proposed as an advanced mode for communication with
printer and scanner type peripherals.
Like the EPP protocol, ECP mode provides
for a high performance bidirectional communication path between the host
adapter and the peripheral.
.Pp
ECP protocol features include:
.Bl -item -offset indent
.It
Run_Length_Encoding (RLE) data compression for host adapters
.It
FIFOs for both the forward and reverse channels
.It
DMA as well as programmed I/O for the host register interface.
.El
.Ss Enhanced Parallel Port mode
The EPP protocol was originally developed as a means to provide a high
performance parallel port link that would still be compatible with the
standard parallel port.
.Pp
The EPP mode has two types of cycle: address and data.
What makes the
difference at hardware level is the strobe of the byte placed on the data
lines.
Data are strobed with nAutofeed, addresses are strobed with
nSelectin signals.
.Pp
A particularity of the ISA implementation of the EPP protocol is that an
EPP cycle fits in an ISA cycle.
In this fashion, parallel port peripherals can
operate at close to the same performance levels as an equivalent ISA plug-in
card.
.Pp
At software level, you may implement the protocol you wish, using data and
address cycles as you want.
This is for the IEEE1284 compatible part.
Then,
peripheral vendors may implement protocol handshake with the following
status lines: PError, nFault and Select.
Try to know how these lines toggle
with your peripheral, allowing the peripheral to request more data, stop the
transfer and so on.
.Pp
At any time, the peripheral may interrupt the host with the nAck signal without
disturbing the current transfer.
.Ss Mixed modes
Some manufacturers, like SMC, have implemented chipsets that support mixed
modes.
With such chipsets, mode switching is available at any time by
accessing the extended control register.
.Sh IEEE1284-1994 Standard
.Ss Background
This standard is also named "IEEE Standard Signaling Method for a
Bidirectional Parallel Peripheral Interface for Personal Computers". It
defines a signaling method for asynchronous, fully interlocked, bidirectional
parallel communications between hosts and printers or other peripherals.
It
also specifies a format for a peripheral identification string and a method of
returning this string to the host outside of the bidirectional data stream.
.Pp
This standard is architecture independent and only specifies dialog handshake
at signal level.
One should refer to architecture specific documentation in
order to manipulate machine dependent registers, mapped memory or other
methods to control these signals.
.Pp
The IEEE1284 protocol is fully oriented with all supported parallel port
modes.
The computer acts as master and the peripheral as slave.
.Pp
Any transfer is defined as a finite state automate.
It allows software to
properly manage the fully interlocked scheme of the signaling method.
The compatible mode is supported "as is" without any negotiation because it
is compatible.
Any other mode must be firstly negotiated by the host to check
it is supported by the peripheral, then to enter one of the forward idle
states.
.Pp
At any time, the slave may want to send data to the host.
This is only
possible from forward idle states (nibble, byte, ecp...).
So, the
host must have previously negotiated to permit the peripheral to
request transfer.
Interrupt lines may be dedicated to the requesting signals
to prevent time consuming polling methods.
.Pp
But peripheral requests are only a hint to the master host.
If the host
accepts the transfer, it must firstly negotiate the reverse mode and then
starts the transfer.
At any time during reverse transfer, the host may
terminate the transfer or the slave may drive wires to signal that no more
data is available.
.Ss Implementation
IEEE1284 Standard support has been implemented at the top of the ppbus system
as a set of procedures that perform high level functions like negotiation,
termination, transfer in any mode without bothering you with low level
characteristics of the standard.
.Pp
IEEE1284 interacts with the ppbus system as least as possible.
That means
you still have to request the ppbus when you want to access it, the negotiate
function doesn't do it for you.
And of course, release it later.
.Sh ARCHITECTURE
.Ss adapter, ppbus and device layers
First, there is the
.Em adapter
layer, the lowest of the ppbus system.
It provides
chipset abstraction throw a set of low level functions that maps the logical
model to the underlying hardware.
.Pp
Secondly, there is the
.Em ppbus
layer that provides functions to:
.Bl -enum -offset indent
.It
share the parallel port bus among the daisy-chain like connected devices
.It
manage devices linked to ppbus
.It
propose an arch-independent interface to access the hardware layer.
.El
.Pp
Finally, the
.Em device
layer gathers the parallel peripheral device drivers.
.Ss Parallel modes management
We have to differentiate operating modes at various ppbus system layers.
Actually, ppbus and adapter operating modes on one hands and for each
one, current and available modes are separated.
.Pp
With this level of abstraction a particular chipset may commute from any
native mode the any other mode emulated with extended modes without
disturbing upper layers.
For example, most chipsets support NIBBLE mode as
native and emulated with ECP and/or EPP.
.Pp
This architecture should support IEEE1284-1994 modes.
.Sh FEATURES
.Ss The boot process
The boot process starts with the probe phasis of the
.Xr ppc 4
driver during ISA bus (PC architecture) initialization.
During attachment of
the ppc driver, a new ppbus structure is allocated, then probe and attachment
for this new bus node are called.
.Pp
ppbus attachment tries to detect any PnP parallel peripheral (according to
.%T "Plug and Play Parallel Port Devices"
draft from (c)1993-4 Microsoft Corporation)
then probes and attaches known device drivers.
.Pp
During probe, device drivers are supposed to request the ppbus and try to
set their operating mode.
This mode will be saved in the context structure and
returned each time the driver requests the ppbus.
.Ss Bus allocation and interrupts
ppbus allocation is mandatory not to corrupt I/O of other devices.
Another
usage of ppbus allocation is to reserve the port and receive incoming
interrupts.
.Pp
High level interrupt handlers are connected to the ppbus system thanks to the
newbus
.Fn BUS_SETUP_INTR
and
.Fn BUS_TEARDOWN_INTR
functions.
But, in order to attach a handler, drivers must
own the bus.
Consequently, a ppbus request is mandatory in order to call the above
functions (see existing drivers for more info). Note that the interrupt handler
is automatically released when the ppbus is released.
.Ss Microsequences
.Em Microsequences
is a general purpose mechanism to allow fast low-level
manipulation of the parallel port.
Microsequences may be used to do either
standard (in IEEE1284 modes) or non-standard transfers.
The philosophy of
microsequences is to avoid the overhead of the ppbus layer and do most of
the job at adapter level.
.Pp
A microsequence is an array of opcodes and parameters.
Each opcode codes an
operation (opcodes are described in
.Xr microseq 9 ) .
Standard I/O operations are implemented at ppbus level whereas basic I/O
operations and microseq language are coded at adapter level for efficiency.
.Pp
As an example, the
.Xr vpo 4
driver uses microsequences to implement:
.Bl -bullet -offset indent
.It
a modified version of the NIBBLE transfer mode
.It
various I/O sequences to initialize, select and allocate the peripheral
.El
.Sh SEE ALSO
.Xr lpt 4 ,
.Xr plip 4 ,
.Xr ppc 4 ,
.Xr ppi 4 ,
.Xr vpo 4
.Sh HISTORY
The
.Nm
manual page first appeared in
.Fx 3.0 .
.Sh AUTHORS
This
manual page was written by
.An Nicolas Souchu .