1 /*- 2 * Copyright (c) 1997, 1998, 1999, 2000-2003 3 * Bill Paul <wpaul@windriver.com>. All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer. 10 * 2. Redistributions in binary form must reproduce the above copyright 11 * notice, this list of conditions and the following disclaimer in the 12 * documentation and/or other materials provided with the distribution. 13 * 3. All advertising materials mentioning features or use of this software 14 * must display the following acknowledgement: 15 * This product includes software developed by Bill Paul. 16 * 4. Neither the name of the author nor the names of any co-contributors 17 * may be used to endorse or promote products derived from this software 18 * without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 21 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 24 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 30 * THE POSSIBILITY OF SUCH DAMAGE. 31 */ 32 33 /* 34 * ASIX Electronics AX88172/AX88178/AX88778 USB 2.0 ethernet driver. 35 * Used in the LinkSys USB200M and various other adapters. 36 * 37 * Manuals available from: 38 * http://www.asix.com.tw/datasheet/mac/Ax88172.PDF 39 * Note: you need the manual for the AX88170 chip (USB 1.x ethernet 40 * controller) to find the definitions for the RX control register. 41 * http://www.asix.com.tw/datasheet/mac/Ax88170.PDF 42 * 43 * Written by Bill Paul <wpaul@windriver.com> 44 * Senior Engineer 45 * Wind River Systems 46 */ 47 48 /* 49 * The AX88172 provides USB ethernet supports at 10 and 100Mbps. 50 * It uses an external PHY (reference designs use a RealTek chip), 51 * and has a 64-bit multicast hash filter. There is some information 52 * missing from the manual which one needs to know in order to make 53 * the chip function: 54 * 55 * - You must set bit 7 in the RX control register, otherwise the 56 * chip won't receive any packets. 57 * - You must initialize all 3 IPG registers, or you won't be able 58 * to send any packets. 59 * 60 * Note that this device appears to only support loading the station 61 * address via autload from the EEPROM (i.e. there's no way to manaully 62 * set it). 63 * 64 * (Adam Weinberger wanted me to name this driver if_gir.c.) 65 */ 66 67 /* 68 * Ax88178 and Ax88772 support backported from the OpenBSD driver. 69 * 2007/02/12, J.R. Oldroyd, fbsd@opal.com 70 * 71 * Manual here: 72 * http://www.asix.com.tw/FrootAttach/datasheet/AX88178_datasheet_Rev10.pdf 73 * http://www.asix.com.tw/FrootAttach/datasheet/AX88772_datasheet_Rev10.pdf 74 */ 75 76 #include <sys/param.h> 77 #include <sys/systm.h> 78 #include <sys/bus.h> 79 #include <sys/condvar.h> 80 #include <sys/endian.h> 81 #include <sys/kernel.h> 82 #include <sys/lock.h> 83 #include <sys/malloc.h> 84 #include <sys/mbuf.h> 85 #include <sys/module.h> 86 #include <sys/socket.h> 87 #include <sys/sockio.h> 88 #include <sys/sysctl.h> 89 90 #include <net/if.h> 91 #include <net/ethernet.h> 92 #include <net/if_types.h> 93 #include <net/if_media.h> 94 #include <net/vlan/if_vlan_var.h> 95 #include <net/ifq_var.h> 96 97 #include <dev/netif/mii_layer/mii.h> 98 #include <dev/netif/mii_layer/miivar.h> 99 100 #include <bus/u4b/usb.h> 101 #include <bus/u4b/usbdi.h> 102 #include <bus/u4b/usbdi_util.h> 103 #include "usbdevs.h" 104 105 #define USB_DEBUG_VAR axe_debug 106 #include <bus/u4b/usb_debug.h> 107 #include <bus/u4b/usb_process.h> 108 109 #include <bus/u4b/net/usb_ethernet.h> 110 #include <bus/u4b/net/if_axereg.h> 111 112 /* 113 * AXE_178_MAX_FRAME_BURST 114 * max frame burst size for Ax88178 and Ax88772 115 * 0 2048 bytes 116 * 1 4096 bytes 117 * 2 8192 bytes 118 * 3 16384 bytes 119 * use the largest your system can handle without USB stalling. 120 * 121 * NB: 88772 parts appear to generate lots of input errors with 122 * a 2K rx buffer and 8K is only slightly faster than 4K on an 123 * EHCI port on a T42 so change at your own risk. 124 */ 125 #define AXE_178_MAX_FRAME_BURST 1 126 127 #define AXE_CSUM_FEATURES (CSUM_IP | CSUM_TCP | CSUM_UDP) 128 129 #ifdef USB_DEBUG 130 static int axe_debug = 0; 131 132 static SYSCTL_NODE(_hw_usb, OID_AUTO, axe, CTLFLAG_RW, 0, "USB axe"); 133 SYSCTL_INT(_hw_usb_axe, OID_AUTO, debug, CTLFLAG_RW, &axe_debug, 0, 134 "Debug level"); 135 #endif 136 137 /* 138 * Various supported device vendors/products. 139 */ 140 static const STRUCT_USB_HOST_ID axe_devs[] = { 141 #define AXE_DEV(v,p,i) { USB_VPI(USB_VENDOR_##v, USB_PRODUCT_##v##_##p, i) } 142 AXE_DEV(ABOCOM, UF200, 0), 143 AXE_DEV(ACERCM, EP1427X2, 0), 144 AXE_DEV(APPLE, ETHERNET, AXE_FLAG_772), 145 AXE_DEV(ASIX, AX88172, 0), 146 AXE_DEV(ASIX, AX88178, AXE_FLAG_178), 147 AXE_DEV(ASIX, AX88772, AXE_FLAG_772), 148 AXE_DEV(ASIX, AX88772A, AXE_FLAG_772A), 149 AXE_DEV(ASIX, AX88772B, AXE_FLAG_772B), 150 AXE_DEV(ASIX, AX88772B_1, AXE_FLAG_772B), 151 AXE_DEV(ATEN, UC210T, 0), 152 AXE_DEV(BELKIN, F5D5055, AXE_FLAG_178), 153 AXE_DEV(BILLIONTON, USB2AR, 0), 154 AXE_DEV(CISCOLINKSYS, USB200MV2, AXE_FLAG_772A), 155 AXE_DEV(COREGA, FETHER_USB2_TX, 0), 156 AXE_DEV(DLINK, DUBE100, 0), 157 AXE_DEV(DLINK, DUBE100B1, AXE_FLAG_772), 158 AXE_DEV(DLINK, DUBE100C1, AXE_FLAG_772B), 159 AXE_DEV(GOODWAY, GWUSB2E, 0), 160 AXE_DEV(IODATA, ETGUS2, AXE_FLAG_178), 161 AXE_DEV(JVC, MP_PRX1, 0), 162 AXE_DEV(LENOVO, ETHERNET, AXE_FLAG_772B), 163 AXE_DEV(LINKSYS2, USB200M, 0), 164 AXE_DEV(LINKSYS4, USB1000, AXE_FLAG_178), 165 AXE_DEV(LOGITEC, LAN_GTJU2A, AXE_FLAG_178), 166 AXE_DEV(MELCO, LUAU2KTX, 0), 167 AXE_DEV(MELCO, LUA3U2AGT, AXE_FLAG_178), 168 AXE_DEV(NETGEAR, FA120, 0), 169 AXE_DEV(OQO, ETHER01PLUS, AXE_FLAG_772), 170 AXE_DEV(PLANEX3, GU1000T, AXE_FLAG_178), 171 AXE_DEV(SITECOM, LN029, 0), 172 AXE_DEV(SITECOMEU, LN028, AXE_FLAG_178), 173 AXE_DEV(SYSTEMTALKS, SGCX2UL, 0), 174 #undef AXE_DEV 175 }; 176 177 static device_probe_t axe_probe; 178 static device_attach_t axe_attach; 179 static device_detach_t axe_detach; 180 181 static usb_callback_t axe_bulk_read_callback; 182 static usb_callback_t axe_bulk_write_callback; 183 184 static miibus_readreg_t axe_miibus_readreg; 185 static miibus_writereg_t axe_miibus_writereg; 186 static miibus_statchg_t axe_miibus_statchg; 187 188 static uether_fn_t axe_attach_post; 189 static uether_fn_t axe_init; 190 static uether_fn_t axe_stop; 191 static uether_fn_t axe_start; 192 static uether_fn_t axe_tick; 193 static uether_fn_t axe_setmulti; 194 static uether_fn_t axe_setpromisc; 195 196 static int axe_attach_post_sub(struct usb_ether *); 197 static int axe_ifmedia_upd(struct ifnet *); 198 static void axe_ifmedia_sts(struct ifnet *, struct ifmediareq *); 199 static int axe_cmd(struct axe_softc *, int, int, int, void *); 200 static void axe_ax88178_init(struct axe_softc *); 201 static void axe_ax88772_init(struct axe_softc *); 202 static void axe_ax88772_phywake(struct axe_softc *); 203 static void axe_ax88772a_init(struct axe_softc *); 204 static void axe_ax88772b_init(struct axe_softc *); 205 static int axe_get_phyno(struct axe_softc *, int); 206 static int axe_ioctl(struct ifnet *, u_long, caddr_t, struct ucred *); 207 static int axe_rx_frame(struct usb_ether *, struct usb_page_cache *, int); 208 static int axe_rxeof(struct usb_ether *, struct usb_page_cache *, 209 unsigned int offset, unsigned int, struct axe_csum_hdr *); 210 static void axe_csum_cfg(struct usb_ether *); 211 212 static const struct usb_config axe_config[AXE_N_TRANSFER] = { 213 214 [AXE_BULK_DT_WR] = { 215 .type = UE_BULK, 216 .endpoint = UE_ADDR_ANY, 217 .direction = UE_DIR_OUT, 218 .frames = 16, 219 .bufsize = 16 * MCLBYTES, 220 .flags = {.pipe_bof = 1,.force_short_xfer = 1,}, 221 .callback = axe_bulk_write_callback, 222 .timeout = 10000, /* 10 seconds */ 223 }, 224 225 [AXE_BULK_DT_RD] = { 226 .type = UE_BULK, 227 .endpoint = UE_ADDR_ANY, 228 .direction = UE_DIR_IN, 229 .bufsize = 16384, /* bytes */ 230 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, 231 .callback = axe_bulk_read_callback, 232 .timeout = 0, /* no timeout */ 233 }, 234 }; 235 236 static const struct ax88772b_mfb ax88772b_mfb_table[] = { 237 { 0x8000, 0x8001, 2048 }, 238 { 0x8100, 0x8147, 4096}, 239 { 0x8200, 0x81EB, 6144}, 240 { 0x8300, 0x83D7, 8192}, 241 { 0x8400, 0x851E, 16384}, 242 { 0x8500, 0x8666, 20480}, 243 { 0x8600, 0x87AE, 24576}, 244 { 0x8700, 0x8A3D, 32768} 245 }; 246 247 static device_method_t axe_methods[] = { 248 /* Device interface */ 249 DEVMETHOD(device_probe, axe_probe), 250 DEVMETHOD(device_attach, axe_attach), 251 DEVMETHOD(device_detach, axe_detach), 252 253 /* MII interface */ 254 DEVMETHOD(miibus_readreg, axe_miibus_readreg), 255 DEVMETHOD(miibus_writereg, axe_miibus_writereg), 256 DEVMETHOD(miibus_statchg, axe_miibus_statchg), 257 258 DEVMETHOD_END 259 }; 260 261 static driver_t axe_driver = { 262 .name = "axe", 263 .methods = axe_methods, 264 .size = sizeof(struct axe_softc), 265 }; 266 267 static devclass_t axe_devclass; 268 269 DRIVER_MODULE(axe, uhub, axe_driver, axe_devclass, NULL, NULL); 270 DRIVER_MODULE(miibus, axe, miibus_driver, miibus_devclass, NULL, NULL); 271 MODULE_DEPEND(axe, uether, 1, 1, 1); 272 MODULE_DEPEND(axe, usb, 1, 1, 1); 273 MODULE_DEPEND(axe, ether, 1, 1, 1); 274 MODULE_DEPEND(axe, miibus, 1, 1, 1); 275 MODULE_VERSION(axe, 1); 276 277 static const struct usb_ether_methods axe_ue_methods = { 278 .ue_attach_post = axe_attach_post, 279 .ue_attach_post_sub = axe_attach_post_sub, 280 .ue_start = axe_start, 281 .ue_init = axe_init, 282 .ue_stop = axe_stop, 283 .ue_tick = axe_tick, 284 .ue_setmulti = axe_setmulti, 285 .ue_setpromisc = axe_setpromisc, 286 .ue_mii_upd = axe_ifmedia_upd, 287 .ue_mii_sts = axe_ifmedia_sts, 288 }; 289 290 static int 291 axe_cmd(struct axe_softc *sc, int cmd, int index, int val, void *buf) 292 { 293 struct usb_device_request req; 294 usb_error_t err; 295 296 AXE_LOCK_ASSERT(sc); 297 298 req.bmRequestType = (AXE_CMD_IS_WRITE(cmd) ? 299 UT_WRITE_VENDOR_DEVICE : 300 UT_READ_VENDOR_DEVICE); 301 req.bRequest = AXE_CMD_CMD(cmd); 302 USETW(req.wValue, val); 303 USETW(req.wIndex, index); 304 USETW(req.wLength, AXE_CMD_LEN(cmd)); 305 306 err = uether_do_request(&sc->sc_ue, &req, buf, 1000); 307 308 return (err); 309 } 310 311 static int 312 axe_miibus_readreg(device_t dev, int phy, int reg) 313 { 314 struct axe_softc *sc = device_get_softc(dev); 315 uint16_t val; 316 int locked; 317 318 locked = lockowned(&sc->sc_lock); 319 if(!locked) 320 AXE_LOCK(sc); 321 322 if(phy != sc->sc_phyno){ 323 if(!locked) 324 AXE_UNLOCK(sc); 325 return(0); 326 } 327 328 axe_cmd(sc, AXE_CMD_MII_OPMODE_SW, 0, 0, NULL); 329 axe_cmd(sc, AXE_CMD_MII_READ_REG, reg, phy, &val); 330 axe_cmd(sc, AXE_CMD_MII_OPMODE_HW, 0, 0, NULL); 331 332 val = le16toh(val); 333 if (AXE_IS_772(sc) && reg == MII_BMSR) { 334 /* 335 * BMSR of AX88772 indicates that it supports extended 336 * capability but the extended status register is 337 * revered for embedded ethernet PHY. So clear the 338 * extended capability bit of BMSR. 339 */ 340 val &= ~BMSR_EXTCAP; 341 } 342 343 if (!locked) 344 AXE_UNLOCK(sc); 345 return (val); 346 } 347 348 static int 349 axe_miibus_writereg(device_t dev, int phy, int reg, int val) 350 { 351 struct axe_softc *sc = device_get_softc(dev); 352 int locked; 353 354 val = htole32(val); 355 locked = lockowned(&sc->sc_lock); 356 if (!locked) 357 AXE_LOCK(sc); 358 359 axe_cmd(sc, AXE_CMD_MII_OPMODE_SW, 0, 0, NULL); 360 axe_cmd(sc, AXE_CMD_MII_WRITE_REG, reg, phy, &val); 361 axe_cmd(sc, AXE_CMD_MII_OPMODE_HW, 0, 0, NULL); 362 363 if (!locked) 364 AXE_UNLOCK(sc); 365 return (0); 366 } 367 368 static void 369 axe_miibus_statchg(device_t dev) 370 { 371 struct axe_softc *sc = device_get_softc(dev); 372 struct mii_data *mii = GET_MII(sc); 373 struct ifnet *ifp; 374 uint16_t val; 375 int err, locked; 376 377 locked = lockowned(&sc->sc_lock); 378 if (!locked) 379 AXE_LOCK(sc); 380 381 ifp = uether_getifp(&sc->sc_ue); 382 if (mii == NULL || ifp == NULL || 383 (ifp->if_flags & IFF_RUNNING) == 0) 384 goto done; 385 386 sc->sc_flags &= ~AXE_FLAG_LINK; 387 if ((mii->mii_media_status & (IFM_ACTIVE | IFM_AVALID)) == 388 (IFM_ACTIVE | IFM_AVALID)) { 389 switch (IFM_SUBTYPE(mii->mii_media_active)) { 390 case IFM_10_T: 391 case IFM_100_TX: 392 sc->sc_flags |= AXE_FLAG_LINK; 393 break; 394 case IFM_1000_T: 395 if ((sc->sc_flags & AXE_FLAG_178) == 0) 396 break; 397 sc->sc_flags |= AXE_FLAG_LINK; 398 DPRINTFN(11, "miibus_statchg: link should be up\n"); 399 break; 400 default: 401 break; 402 } 403 } else { 404 DPRINTFN(11, "miibus_statchg: not active or not valid: %x\n", mii->mii_media_status); 405 } 406 407 /* Lost link, do nothing. */ 408 if ((sc->sc_flags & AXE_FLAG_LINK) == 0) { 409 goto done; 410 } 411 412 val = 0; 413 if ((IFM_OPTIONS(mii->mii_media_active) & IFM_FDX) != 0) { 414 val |= AXE_MEDIA_FULL_DUPLEX; 415 if (AXE_IS_178_FAMILY(sc)) { 416 if ((IFM_OPTIONS(mii->mii_media_active) & 417 IFM_ETH_TXPAUSE) != 0) 418 val |= AXE_178_MEDIA_TXFLOW_CONTROL_EN; 419 if ((IFM_OPTIONS(mii->mii_media_active) & 420 IFM_ETH_RXPAUSE) != 0) 421 val |= AXE_178_MEDIA_RXFLOW_CONTROL_EN; 422 } 423 } 424 if (AXE_IS_178_FAMILY(sc)) { 425 val |= AXE_178_MEDIA_RX_EN | AXE_178_MEDIA_MAGIC; 426 if ((sc->sc_flags & AXE_FLAG_178) != 0) 427 val |= AXE_178_MEDIA_ENCK; 428 switch (IFM_SUBTYPE(mii->mii_media_active)) { 429 case IFM_1000_T: 430 val |= AXE_178_MEDIA_GMII | AXE_178_MEDIA_ENCK; 431 break; 432 case IFM_100_TX: 433 val |= AXE_178_MEDIA_100TX; 434 break; 435 case IFM_10_T: 436 /* doesn't need to be handled */ 437 break; 438 } 439 } 440 err = axe_cmd(sc, AXE_CMD_WRITE_MEDIA, 0, val, NULL); 441 if (err) 442 device_printf(dev, "media change failed, error %d\n", err); 443 done: 444 if (!locked) 445 AXE_UNLOCK(sc); 446 } 447 448 /* 449 * Set media options. 450 */ 451 static int 452 axe_ifmedia_upd(struct ifnet *ifp) 453 { 454 struct axe_softc *sc = ifp->if_softc; 455 struct mii_data *mii = GET_MII(sc); 456 struct mii_softc *miisc; 457 int error; 458 459 AXE_LOCK_ASSERT(sc); 460 461 LIST_FOREACH(miisc, &mii->mii_phys, mii_list) 462 mii_phy_reset(miisc); 463 error = mii_mediachg(mii); 464 return (error); 465 } 466 467 /* 468 * Report current media status. 469 */ 470 static void 471 axe_ifmedia_sts(struct ifnet *ifp, struct ifmediareq *ifmr) 472 { 473 struct axe_softc *sc = ifp->if_softc; 474 struct mii_data *mii = GET_MII(sc); 475 476 AXE_LOCK(sc); 477 mii_pollstat(mii); 478 ifmr->ifm_active = mii->mii_media_active; 479 ifmr->ifm_status = mii->mii_media_status; 480 AXE_UNLOCK(sc); 481 } 482 483 static void 484 axe_setmulti(struct usb_ether *ue) 485 { 486 struct axe_softc *sc = uether_getsc(ue); 487 struct ifnet *ifp = uether_getifp(ue); 488 struct ifmultiaddr *ifma; 489 uint32_t h = 0; 490 uint16_t rxmode; 491 uint8_t hashtbl[8] = { 0, 0, 0, 0, 0, 0, 0, 0 }; 492 493 AXE_LOCK_ASSERT(sc); 494 495 axe_cmd(sc, AXE_CMD_RXCTL_READ, 0, 0, &rxmode); 496 rxmode = le16toh(rxmode); 497 498 if (ifp->if_flags & (IFF_ALLMULTI | IFF_PROMISC)) { 499 rxmode |= AXE_RXCMD_ALLMULTI; 500 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, rxmode, NULL); 501 return; 502 } 503 rxmode &= ~AXE_RXCMD_ALLMULTI; 504 505 /* if_maddr_rlock(ifp); */ 506 TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) 507 { 508 if (ifma->ifma_addr->sa_family != AF_LINK) 509 continue; 510 h = ether_crc32_be(LLADDR((struct sockaddr_dl *) 511 ifma->ifma_addr), ETHER_ADDR_LEN) >> 26; 512 hashtbl[h / 8] |= 1 << (h % 8); 513 } 514 /* if_maddr_runlock(ifp); */ 515 516 axe_cmd(sc, AXE_CMD_WRITE_MCAST, 0, 0, (void *)&hashtbl); 517 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, rxmode, NULL); 518 } 519 520 static int 521 axe_get_phyno(struct axe_softc *sc, int sel) 522 { 523 int phyno; 524 525 switch (AXE_PHY_TYPE(sc->sc_phyaddrs[sel])) { 526 case PHY_TYPE_100_HOME: 527 case PHY_TYPE_GIG: 528 phyno = AXE_PHY_NO(sc->sc_phyaddrs[sel]); 529 break; 530 case PHY_TYPE_SPECIAL: 531 /* FALLTHROUGH */ 532 case PHY_TYPE_RSVD: 533 /* FALLTHROUGH */ 534 case PHY_TYPE_NON_SUP: 535 /* FALLTHROUGH */ 536 default: 537 phyno = -1; 538 break; 539 } 540 541 return (phyno); 542 } 543 544 #define AXE_GPIO_WRITE(x, y) do { \ 545 axe_cmd(sc, AXE_CMD_WRITE_GPIO, 0, (x), NULL); \ 546 uether_pause(ue, (y)); \ 547 } while (0) 548 549 static void 550 axe_ax88178_init(struct axe_softc *sc) 551 { 552 struct usb_ether *ue; 553 int gpio0, ledmode, phymode; 554 uint16_t eeprom, val; 555 556 ue = &sc->sc_ue; 557 axe_cmd(sc, AXE_CMD_SROM_WR_ENABLE, 0, 0, NULL); 558 /* XXX magic */ 559 axe_cmd(sc, AXE_CMD_SROM_READ, 0, 0x0017, &eeprom); 560 eeprom = le16toh(eeprom); 561 axe_cmd(sc, AXE_CMD_SROM_WR_DISABLE, 0, 0, NULL); 562 563 /* if EEPROM is invalid we have to use to GPIO0 */ 564 if (eeprom == 0xffff) { 565 phymode = AXE_PHY_MODE_MARVELL; 566 gpio0 = 1; 567 ledmode = 0; 568 } else { 569 phymode = eeprom & 0x7f; 570 gpio0 = (eeprom & 0x80) ? 0 : 1; 571 ledmode = eeprom >> 8; 572 } 573 574 if (bootverbose) 575 device_printf(sc->sc_ue.ue_dev, 576 "EEPROM data : 0x%04x, phymode : 0x%02x\n", eeprom, 577 phymode); 578 /* Program GPIOs depending on PHY hardware. */ 579 switch (phymode) { 580 case AXE_PHY_MODE_MARVELL: 581 if (gpio0 == 1) { 582 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM | AXE_GPIO0_EN, 583 hz / 32); 584 AXE_GPIO_WRITE(AXE_GPIO0_EN | AXE_GPIO2 | AXE_GPIO2_EN, 585 hz / 32); 586 AXE_GPIO_WRITE(AXE_GPIO0_EN | AXE_GPIO2_EN, hz / 4); 587 AXE_GPIO_WRITE(AXE_GPIO0_EN | AXE_GPIO2 | AXE_GPIO2_EN, 588 hz / 32); 589 } else { 590 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM | AXE_GPIO1 | 591 AXE_GPIO1_EN, hz / 3); 592 if (ledmode == 1) { 593 AXE_GPIO_WRITE(AXE_GPIO1_EN, hz / 3); 594 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN, 595 hz / 3); 596 } else { 597 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | 598 AXE_GPIO2 | AXE_GPIO2_EN, hz / 32); 599 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | 600 AXE_GPIO2_EN, hz / 4); 601 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | 602 AXE_GPIO2 | AXE_GPIO2_EN, hz / 32); 603 } 604 } 605 break; 606 case AXE_PHY_MODE_CICADA: 607 case AXE_PHY_MODE_CICADA_V2: 608 case AXE_PHY_MODE_CICADA_V2_ASIX: 609 if (gpio0 == 1) 610 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM | AXE_GPIO0 | 611 AXE_GPIO0_EN, hz / 32); 612 else 613 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM | AXE_GPIO1 | 614 AXE_GPIO1_EN, hz / 32); 615 break; 616 case AXE_PHY_MODE_AGERE: 617 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM | AXE_GPIO1 | 618 AXE_GPIO1_EN, hz / 32); 619 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | AXE_GPIO2 | 620 AXE_GPIO2_EN, hz / 32); 621 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | AXE_GPIO2_EN, hz / 4); 622 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | AXE_GPIO2 | 623 AXE_GPIO2_EN, hz / 32); 624 break; 625 case AXE_PHY_MODE_REALTEK_8211CL: 626 case AXE_PHY_MODE_REALTEK_8211BN: 627 case AXE_PHY_MODE_REALTEK_8251CL: 628 val = gpio0 == 1 ? AXE_GPIO0 | AXE_GPIO0_EN : 629 AXE_GPIO1 | AXE_GPIO1_EN; 630 AXE_GPIO_WRITE(val, hz / 32); 631 AXE_GPIO_WRITE(val | AXE_GPIO2 | AXE_GPIO2_EN, hz / 32); 632 AXE_GPIO_WRITE(val | AXE_GPIO2_EN, hz / 4); 633 AXE_GPIO_WRITE(val | AXE_GPIO2 | AXE_GPIO2_EN, hz / 32); 634 if (phymode == AXE_PHY_MODE_REALTEK_8211CL) { 635 axe_miibus_writereg(ue->ue_dev, sc->sc_phyno, 636 0x1F, 0x0005); 637 axe_miibus_writereg(ue->ue_dev, sc->sc_phyno, 638 0x0C, 0x0000); 639 val = axe_miibus_readreg(ue->ue_dev, sc->sc_phyno, 640 0x0001); 641 axe_miibus_writereg(ue->ue_dev, sc->sc_phyno, 642 0x01, val | 0x0080); 643 axe_miibus_writereg(ue->ue_dev, sc->sc_phyno, 644 0x1F, 0x0000); 645 } 646 break; 647 default: 648 /* Unknown PHY model or no need to program GPIOs. */ 649 break; 650 } 651 652 /* soft reset */ 653 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_CLEAR, NULL); 654 uether_pause(ue, hz / 4); 655 656 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, 657 AXE_SW_RESET_PRL | AXE_178_RESET_MAGIC, NULL); 658 uether_pause(ue, hz / 4); 659 /* Enable MII/GMII/RGMII interface to work with external PHY. */ 660 axe_cmd(sc, AXE_CMD_SW_PHY_SELECT, 0, 0, NULL); 661 uether_pause(ue, hz / 4); 662 663 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, 0, NULL); 664 } 665 666 static void 667 axe_ax88772_init(struct axe_softc *sc) 668 { 669 axe_cmd(sc, AXE_CMD_WRITE_GPIO, 0, 0x00b0, NULL); 670 uether_pause(&sc->sc_ue, hz / 16); 671 672 if (sc->sc_phyno == AXE_772_PHY_NO_EPHY) { 673 /* ask for the embedded PHY */ 674 axe_cmd(sc, AXE_CMD_SW_PHY_SELECT, 0, 0x01, NULL); 675 uether_pause(&sc->sc_ue, hz / 64); 676 677 /* power down and reset state, pin reset state */ 678 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, 679 AXE_SW_RESET_CLEAR, NULL); 680 uether_pause(&sc->sc_ue, hz / 16); 681 682 /* power down/reset state, pin operating state */ 683 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, 684 AXE_SW_RESET_IPPD | AXE_SW_RESET_PRL, NULL); 685 uether_pause(&sc->sc_ue, hz / 4); 686 687 /* power up, reset */ 688 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_PRL, NULL); 689 690 /* power up, operating */ 691 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, 692 AXE_SW_RESET_IPRL | AXE_SW_RESET_PRL, NULL); 693 } else { 694 /* ask for external PHY */ 695 axe_cmd(sc, AXE_CMD_SW_PHY_SELECT, 0, 0x00, NULL); 696 uether_pause(&sc->sc_ue, hz / 64); 697 698 /* power down internal PHY */ 699 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, 700 AXE_SW_RESET_IPPD | AXE_SW_RESET_PRL, NULL); 701 } 702 703 uether_pause(&sc->sc_ue, hz / 4); 704 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, 0, NULL); 705 } 706 707 static void 708 axe_ax88772_phywake(struct axe_softc *sc) 709 { 710 struct usb_ether *ue; 711 712 ue = &sc->sc_ue; 713 if (sc->sc_phyno == AXE_772_PHY_NO_EPHY) { 714 /* Manually select internal(embedded) PHY - MAC mode. */ 715 axe_cmd(sc, AXE_CMD_SW_PHY_SELECT, 0, AXE_SW_PHY_SELECT_SS_ENB | 716 AXE_SW_PHY_SELECT_EMBEDDED | AXE_SW_PHY_SELECT_SS_MII, 717 NULL); 718 uether_pause(&sc->sc_ue, hz / 32); 719 } else { 720 /* 721 * Manually select external PHY - MAC mode. 722 * Reverse MII/RMII is for AX88772A PHY mode. 723 */ 724 axe_cmd(sc, AXE_CMD_SW_PHY_SELECT, 0, AXE_SW_PHY_SELECT_SS_ENB | 725 AXE_SW_PHY_SELECT_EXT | AXE_SW_PHY_SELECT_SS_MII, NULL); 726 uether_pause(&sc->sc_ue, hz / 32); 727 } 728 /* Take PHY out of power down. */ 729 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_IPPD | 730 AXE_SW_RESET_IPRL, NULL); 731 uether_pause(&sc->sc_ue, hz / 4); 732 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_IPRL, NULL); 733 uether_pause(&sc->sc_ue, hz); 734 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_CLEAR, NULL); 735 uether_pause(&sc->sc_ue, hz / 32); 736 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_IPRL, NULL); 737 uether_pause(&sc->sc_ue, hz / 32); 738 } 739 740 static void 741 axe_ax88772a_init(struct axe_softc *sc) 742 { 743 struct usb_ether *ue; 744 745 ue = &sc->sc_ue; 746 /* Reload EEPROM. */ 747 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM, hz / 32); 748 axe_ax88772_phywake(sc); 749 /* Stop MAC. */ 750 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, 0, NULL); 751 } 752 753 static void 754 axe_ax88772b_init(struct axe_softc *sc) 755 { 756 struct usb_ether *ue; 757 uint16_t eeprom; 758 uint8_t *eaddr; 759 int i; 760 761 ue = &sc->sc_ue; 762 /* Reload EEPROM. */ 763 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM, hz / 32); 764 /* 765 * Save PHY power saving configuration(high byte) and 766 * clear EEPROM checksum value(low byte). 767 */ 768 axe_cmd(sc, AXE_CMD_SROM_READ, 0, AXE_EEPROM_772B_PHY_PWRCFG, &eeprom); 769 sc->sc_pwrcfg = le16toh(eeprom) & 0xFF00; 770 771 /* 772 * Auto-loaded default station address from internal ROM is 773 * 00:00:00:00:00:00 such that an explicit access to EEPROM 774 * is required to get real station address. 775 */ 776 eaddr = ue->ue_eaddr; 777 for (i = 0; i < ETHER_ADDR_LEN / 2; i++) { 778 axe_cmd(sc, AXE_CMD_SROM_READ, 0, AXE_EEPROM_772B_NODE_ID + i, 779 &eeprom); 780 eeprom = le16toh(eeprom); 781 *eaddr++ = (uint8_t)(eeprom & 0xFF); 782 *eaddr++ = (uint8_t)((eeprom >> 8) & 0xFF); 783 } 784 /* Wakeup PHY. */ 785 axe_ax88772_phywake(sc); 786 /* Stop MAC. */ 787 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, 0, NULL); 788 } 789 790 #undef AXE_GPIO_WRITE 791 792 static void 793 axe_reset(struct axe_softc *sc) 794 { 795 struct usb_config_descriptor *cd; 796 usb_error_t err; 797 798 cd = usbd_get_config_descriptor(sc->sc_ue.ue_udev); 799 800 err = usbd_req_set_config(sc->sc_ue.ue_udev, &sc->sc_lock, 801 cd->bConfigurationValue); 802 if (err) 803 DPRINTF("reset failed (ignored)\n"); 804 805 /* Wait a little while for the chip to get its brains in order. */ 806 uether_pause(&sc->sc_ue, hz / 100); 807 808 /* Reinitialize controller to achieve full reset. */ 809 if (sc->sc_flags & AXE_FLAG_178) 810 axe_ax88178_init(sc); 811 else if (sc->sc_flags & AXE_FLAG_772) 812 axe_ax88772_init(sc); 813 else if (sc->sc_flags & AXE_FLAG_772A) 814 axe_ax88772a_init(sc); 815 else if (sc->sc_flags & AXE_FLAG_772B) 816 axe_ax88772b_init(sc); 817 } 818 819 static void 820 axe_attach_post(struct usb_ether *ue) 821 { 822 struct axe_softc *sc = uether_getsc(ue); 823 824 /* 825 * Load PHY indexes first. Needed by axe_xxx_init(). 826 */ 827 axe_cmd(sc, AXE_CMD_READ_PHYID, 0, 0, sc->sc_phyaddrs); 828 if (bootverbose) 829 device_printf(sc->sc_ue.ue_dev, "PHYADDR 0x%02x:0x%02x\n", 830 sc->sc_phyaddrs[0], sc->sc_phyaddrs[1]); 831 sc->sc_phyno = axe_get_phyno(sc, AXE_PHY_SEL_PRI); 832 if (sc->sc_phyno == -1) 833 sc->sc_phyno = axe_get_phyno(sc, AXE_PHY_SEL_SEC); 834 if (sc->sc_phyno == -1) { 835 device_printf(sc->sc_ue.ue_dev, 836 "no valid PHY address found, assuming PHY address 0\n"); 837 sc->sc_phyno = 0; 838 } 839 840 /* Initialize controller and get station address. */ 841 if (sc->sc_flags & AXE_FLAG_178) { 842 axe_ax88178_init(sc); 843 axe_cmd(sc, AXE_178_CMD_READ_NODEID, 0, 0, ue->ue_eaddr); 844 } else if (sc->sc_flags & AXE_FLAG_772) { 845 axe_ax88772_init(sc); 846 axe_cmd(sc, AXE_178_CMD_READ_NODEID, 0, 0, ue->ue_eaddr); 847 } else if (sc->sc_flags & AXE_FLAG_772A) { 848 axe_ax88772a_init(sc); 849 axe_cmd(sc, AXE_178_CMD_READ_NODEID, 0, 0, ue->ue_eaddr); 850 } else if (sc->sc_flags & AXE_FLAG_772B) { 851 axe_ax88772b_init(sc); 852 } else 853 axe_cmd(sc, AXE_172_CMD_READ_NODEID, 0, 0, ue->ue_eaddr); 854 855 /* 856 * Fetch IPG values. 857 */ 858 if (sc->sc_flags & (AXE_FLAG_772A | AXE_FLAG_772B)) { 859 /* Set IPG values. */ 860 sc->sc_ipgs[0] = 0x15; 861 sc->sc_ipgs[1] = 0x16; 862 sc->sc_ipgs[2] = 0x1A; 863 } else { 864 axe_cmd(sc, AXE_CMD_READ_IPG012, 0, 0, sc->sc_ipgs); 865 } 866 } 867 868 static int 869 axe_attach_post_sub(struct usb_ether *ue) 870 { 871 struct axe_softc *sc; 872 struct ifnet *ifp; 873 u_int adv_pause; 874 int error; 875 876 sc = uether_getsc(ue); 877 ifp = uether_getifp(ue); 878 ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; 879 ifp->if_start = uether_start; 880 ifp->if_ioctl = axe_ioctl; 881 ifp->if_init = uether_init; 882 ifq_set_maxlen(&ifp->if_snd, ifqmaxlen); 883 ifq_set_ready(&ifp->if_snd); 884 885 if (AXE_IS_178_FAMILY(sc)) 886 ifp->if_capabilities |= IFCAP_VLAN_MTU; 887 if (sc->sc_flags & AXE_FLAG_772B) { 888 ifp->if_capabilities |= IFCAP_TXCSUM | IFCAP_RXCSUM; 889 ifp->if_hwassist = AXE_CSUM_FEATURES; 890 /* 891 * Checksum offloading of AX88772B also works with VLAN 892 * tagged frames but there is no way to take advantage 893 * of the feature because vlan(4) assumes 894 * IFCAP_VLAN_HWTAGGING is prerequisite condition to 895 * support checksum offloading with VLAN. VLAN hardware 896 * tagging support of AX88772B is very limited so it's 897 * not possible to announce IFCAP_VLAN_HWTAGGING. 898 */ 899 } 900 ifp->if_capenable = ifp->if_capabilities; 901 if (sc->sc_flags & (AXE_FLAG_772A | AXE_FLAG_772B | AXE_FLAG_178)) 902 adv_pause = MIIF_DOPAUSE; 903 else 904 adv_pause = 0; 905 906 /* Careful, miibus assumes that the first member of the softc 907 of it's parent is an arpcom structure --mpf */ 908 error = mii_phy_probe(ue->ue_dev, &ue->ue_miibus, 909 uether_ifmedia_upd, ue->ue_methods->ue_mii_sts); 910 911 return (error); 912 } 913 914 /* 915 * Probe for a AX88172 chip. 916 */ 917 static int 918 axe_probe(device_t dev) 919 { 920 struct usb_attach_arg *uaa = device_get_ivars(dev); 921 922 if (uaa->usb_mode != USB_MODE_HOST) 923 return (ENXIO); 924 if (uaa->info.bConfigIndex != AXE_CONFIG_IDX) 925 return (ENXIO); 926 if (uaa->info.bIfaceIndex != AXE_IFACE_IDX) 927 return (ENXIO); 928 929 return (usbd_lookup_id_by_uaa(axe_devs, sizeof(axe_devs), uaa)); 930 } 931 932 /* 933 * Attach the interface. Allocate softc structures, do ifmedia 934 * setup and ethernet/BPF attach. 935 */ 936 static int 937 axe_attach(device_t dev) 938 { 939 struct usb_attach_arg *uaa = device_get_ivars(dev); 940 struct axe_softc *sc = device_get_softc(dev); 941 struct usb_ether *ue = &sc->sc_ue; 942 uint8_t iface_index; 943 int error; 944 945 sc->sc_flags = USB_GET_DRIVER_INFO(uaa); 946 947 device_set_usb_desc(dev); 948 949 lockinit(&sc->sc_lock, device_get_nameunit(dev), 0, 0); 950 951 iface_index = AXE_IFACE_IDX; 952 error = usbd_transfer_setup(uaa->device, &iface_index, sc->sc_xfer, 953 axe_config, AXE_N_TRANSFER, sc, &sc->sc_lock); 954 if (error) { 955 device_printf(dev, "allocating USB transfers failed\n"); 956 goto detach; 957 } 958 959 ue->ue_sc = sc; 960 ue->ue_dev = dev; 961 ue->ue_udev = uaa->device; 962 ue->ue_lock = &sc->sc_lock; 963 ue->ue_methods = &axe_ue_methods; 964 965 error = uether_ifattach(ue); 966 if (error) { 967 device_printf(dev, "could not attach interface\n"); 968 goto detach; 969 } 970 return (0); /* success */ 971 972 detach: 973 axe_detach(dev); 974 return (ENXIO); /* failure */ 975 } 976 977 static int 978 axe_detach(device_t dev) 979 { 980 struct axe_softc *sc = device_get_softc(dev); 981 struct usb_ether *ue = &sc->sc_ue; 982 983 usbd_transfer_unsetup(sc->sc_xfer, AXE_N_TRANSFER); 984 uether_ifdetach(ue); 985 lockuninit(&sc->sc_lock); 986 987 return (0); 988 } 989 990 #if (AXE_BULK_BUF_SIZE >= 0x10000) 991 #error "Please update axe_bulk_read_callback()!" 992 #endif 993 994 static void 995 axe_bulk_read_callback(struct usb_xfer *xfer, usb_error_t error) 996 { 997 struct axe_softc *sc = usbd_xfer_softc(xfer); 998 struct usb_ether *ue = &sc->sc_ue; 999 struct usb_page_cache *pc; 1000 int actlen; 1001 1002 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); 1003 1004 switch (USB_GET_STATE(xfer)) { 1005 case USB_ST_TRANSFERRED: 1006 pc = usbd_xfer_get_frame(xfer, 0); 1007 axe_rx_frame(ue, pc, actlen); 1008 1009 /* FALLTHROUGH */ 1010 case USB_ST_SETUP: 1011 tr_setup: 1012 usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); 1013 usbd_transfer_submit(xfer); 1014 uether_rxflush(ue); 1015 return; 1016 1017 default: /* Error */ 1018 DPRINTF("bulk read error, %s\n", usbd_errstr(error)); 1019 1020 if (error != USB_ERR_CANCELLED) { 1021 /* try to clear stall first */ 1022 usbd_xfer_set_stall(xfer); 1023 goto tr_setup; 1024 } 1025 return; 1026 1027 } 1028 } 1029 1030 static int 1031 axe_rx_frame(struct usb_ether *ue, struct usb_page_cache *pc, int actlen) 1032 { 1033 struct axe_softc *sc; 1034 struct axe_sframe_hdr hdr; 1035 struct axe_csum_hdr csum_hdr; 1036 int error, len, pos; 1037 1038 sc = uether_getsc(ue); 1039 pos = 0; 1040 len = 0; 1041 error = 0; 1042 if ((sc->sc_flags & AXE_FLAG_STD_FRAME) != 0) { 1043 while (pos < actlen) { 1044 if ((int)(pos + sizeof(hdr)) > actlen) { 1045 /* too little data */ 1046 error = EINVAL; 1047 break; 1048 } 1049 usbd_copy_out(pc, pos, &hdr, sizeof(hdr)); 1050 1051 if ((hdr.len ^ hdr.ilen) != sc->sc_lenmask) { 1052 /* we lost sync */ 1053 error = EINVAL; 1054 break; 1055 } 1056 pos += sizeof(hdr); 1057 len = le16toh(hdr.len); 1058 if (pos + len > actlen) { 1059 /* invalid length */ 1060 error = EINVAL; 1061 break; 1062 } 1063 axe_rxeof(ue, pc, pos, len, NULL); 1064 pos += len + (len % 2); 1065 } 1066 } else if ((sc->sc_flags & AXE_FLAG_CSUM_FRAME) != 0) { 1067 while (pos < actlen) { 1068 if ((int)(pos + sizeof(csum_hdr)) > actlen) { 1069 /* too little data */ 1070 error = EINVAL; 1071 break; 1072 } 1073 usbd_copy_out(pc, pos, &csum_hdr, sizeof(csum_hdr)); 1074 1075 csum_hdr.len = le16toh(csum_hdr.len); 1076 csum_hdr.ilen = le16toh(csum_hdr.ilen); 1077 csum_hdr.cstatus = le16toh(csum_hdr.cstatus); 1078 if ((AXE_CSUM_RXBYTES(csum_hdr.len) ^ 1079 AXE_CSUM_RXBYTES(csum_hdr.ilen)) != 1080 sc->sc_lenmask) { 1081 /* we lost sync */ 1082 error = EINVAL; 1083 break; 1084 } 1085 /* 1086 * Get total transferred frame length including 1087 * checksum header. The length should be multiple 1088 * of 4. 1089 */ 1090 len = sizeof(csum_hdr) + AXE_CSUM_RXBYTES(csum_hdr.len); 1091 len = (len + 3) & ~3; 1092 if (pos + len > actlen) { 1093 /* invalid length */ 1094 error = EINVAL; 1095 break; 1096 } 1097 axe_rxeof(ue, pc, pos + sizeof(csum_hdr), 1098 AXE_CSUM_RXBYTES(csum_hdr.len), &csum_hdr); 1099 pos += len; 1100 } 1101 } else 1102 axe_rxeof(ue, pc, 0, actlen, NULL); 1103 1104 if (error != 0) 1105 IFNET_STAT_INC(uether_getifp(ue), ierrors, 1); 1106 return (error); 1107 } 1108 1109 static int 1110 axe_rxeof(struct usb_ether *ue, struct usb_page_cache *pc, unsigned int offset, 1111 unsigned int len, struct axe_csum_hdr *csum_hdr) 1112 { 1113 struct ifnet *ifp = uether_getifp(ue); 1114 struct mbuf *m; 1115 1116 if (len < ETHER_HDR_LEN || len > MCLBYTES - ETHER_ALIGN) { 1117 IFNET_STAT_INC(ifp, ierrors, 1); 1118 return (EINVAL); 1119 } 1120 1121 m = m_getcl(M_NOWAIT, MT_DATA, M_PKTHDR); 1122 if (m == NULL) { 1123 IFNET_STAT_INC(ifp, iqdrops, 1); 1124 return (ENOMEM); 1125 } 1126 m->m_len = m->m_pkthdr.len = MCLBYTES; 1127 m_adj(m, ETHER_ALIGN); 1128 1129 usbd_copy_out(pc, offset, mtod(m, uint8_t *), len); 1130 1131 IFNET_STAT_INC(ifp, ipackets, 1); 1132 m->m_pkthdr.rcvif = ifp; 1133 m->m_pkthdr.len = m->m_len = len; 1134 1135 if (csum_hdr != NULL && csum_hdr->cstatus & AXE_CSUM_HDR_L3_TYPE_IPV4) { 1136 if ((csum_hdr->cstatus & (AXE_CSUM_HDR_L4_CSUM_ERR | 1137 AXE_CSUM_HDR_L3_CSUM_ERR)) == 0) { 1138 m->m_pkthdr.csum_flags |= CSUM_IP_CHECKED | 1139 CSUM_IP_VALID; 1140 if ((csum_hdr->cstatus & AXE_CSUM_HDR_L4_TYPE_MASK) == 1141 AXE_CSUM_HDR_L4_TYPE_TCP || 1142 (csum_hdr->cstatus & AXE_CSUM_HDR_L4_TYPE_MASK) == 1143 AXE_CSUM_HDR_L4_TYPE_UDP) { 1144 m->m_pkthdr.csum_flags |= 1145 CSUM_DATA_VALID | CSUM_PSEUDO_HDR; 1146 m->m_pkthdr.csum_data = 0xffff; 1147 } 1148 } 1149 } 1150 1151 IF_ENQUEUE(&ue->ue_rxq, m); 1152 return (0); 1153 } 1154 1155 #if ((AXE_BULK_BUF_SIZE >= 0x10000) || (AXE_BULK_BUF_SIZE < (MCLBYTES+4))) 1156 #error "Please update axe_bulk_write_callback()!" 1157 #endif 1158 1159 static void 1160 axe_bulk_write_callback(struct usb_xfer *xfer, usb_error_t error) 1161 { 1162 struct axe_softc *sc = usbd_xfer_softc(xfer); 1163 struct axe_sframe_hdr hdr; 1164 struct ifnet *ifp = uether_getifp(&sc->sc_ue); 1165 struct usb_page_cache *pc; 1166 struct mbuf *m; 1167 int nframes, pos; 1168 1169 DPRINTFN(11, "starting transfer\n"); 1170 1171 switch (USB_GET_STATE(xfer)) { 1172 case USB_ST_TRANSFERRED: 1173 DPRINTFN(11, "transfer complete\n"); 1174 1175 ifq_clr_oactive(&ifp->if_snd); 1176 1177 /* FALLTHROUGH */ 1178 case USB_ST_SETUP: 1179 tr_setup: 1180 if ((sc->sc_flags & AXE_FLAG_LINK) == 0 || 1181 ifq_is_oactive(&ifp->if_snd)) { 1182 /* 1183 * Don't send anything if there is no link or 1184 * controller is busy. 1185 */ 1186 DPRINTFN(11, "controller busy: sc_flags: %x if_flags %x\n",sc->sc_flags, ifp->if_flags); 1187 return; 1188 } 1189 1190 DPRINTFN(11, "copying frames, 16 at a time\n"); 1191 for (nframes = 0; nframes < 16 && 1192 !ifq_is_empty(&ifp->if_snd); nframes++) { 1193 m = ifq_dequeue(&ifp->if_snd); 1194 if (m == NULL) 1195 break; 1196 usbd_xfer_set_frame_offset(xfer, nframes * MCLBYTES, 1197 nframes); 1198 pos = 0; 1199 pc = usbd_xfer_get_frame(xfer, nframes); 1200 if (AXE_IS_178_FAMILY(sc)) { 1201 hdr.len = htole16(m->m_pkthdr.len); 1202 hdr.ilen = ~hdr.len; 1203 /* 1204 * If upper stack computed checksum, driver 1205 * should tell controller not to insert 1206 * computed checksum for checksum offloading 1207 * enabled controller. 1208 */ 1209 if (ifp->if_capabilities & IFCAP_TXCSUM) { 1210 if ((m->m_pkthdr.csum_flags & 1211 AXE_CSUM_FEATURES) != 0) 1212 hdr.len |= htole16( 1213 AXE_TX_CSUM_PSEUDO_HDR); 1214 else 1215 hdr.len |= htole16( 1216 AXE_TX_CSUM_DIS); 1217 } 1218 DPRINTFN(11, "usbd copy in\n"); 1219 usbd_copy_in(pc, pos, &hdr, sizeof(hdr)); 1220 pos += sizeof(hdr); 1221 usbd_m_copy_in(pc, pos, m, 0, m->m_pkthdr.len); 1222 pos += m->m_pkthdr.len; 1223 if ((pos % 512) == 0) { 1224 hdr.len = 0; 1225 hdr.ilen = 0xffff; 1226 usbd_copy_in(pc, pos, &hdr, 1227 sizeof(hdr)); 1228 pos += sizeof(hdr); 1229 } 1230 } else { 1231 usbd_m_copy_in(pc, pos, m, 0, m->m_pkthdr.len); 1232 pos += m->m_pkthdr.len; 1233 } 1234 1235 /* 1236 * XXX 1237 * Update TX packet counter here. This is not 1238 * correct way but it seems that there is no way 1239 * to know how many packets are sent at the end 1240 * of transfer because controller combines 1241 * multiple writes into single one if there is 1242 * room in TX buffer of controller. 1243 */ 1244 IFNET_STAT_INC(ifp, opackets, 1); 1245 1246 /* 1247 * if there's a BPF listener, bounce a copy 1248 * of this frame to him: 1249 */ 1250 BPF_MTAP(ifp, m); 1251 1252 m_freem(m); 1253 1254 /* Set frame length. */ 1255 usbd_xfer_set_frame_len(xfer, nframes, pos); 1256 } 1257 if (nframes != 0) { 1258 usbd_xfer_set_frames(xfer, nframes); 1259 DPRINTFN(5, "submitting transfer\n"); 1260 usbd_transfer_submit(xfer); 1261 ifq_set_oactive(&ifp->if_snd); 1262 } 1263 return; 1264 /* NOTREACHED */ 1265 default: /* Error */ 1266 DPRINTFN(11, "transfer error, %s\n", 1267 usbd_errstr(error)); 1268 1269 IFNET_STAT_INC(ifp, oerrors, 1); 1270 ifq_clr_oactive(&ifp->if_snd); 1271 if (error != USB_ERR_CANCELLED) { 1272 /* try to clear stall first */ 1273 usbd_xfer_set_stall(xfer); 1274 goto tr_setup; 1275 } 1276 return; 1277 1278 } 1279 } 1280 1281 static void 1282 axe_tick(struct usb_ether *ue) 1283 { 1284 struct axe_softc *sc = uether_getsc(ue); 1285 struct mii_data *mii = GET_MII(sc); 1286 1287 AXE_LOCK_ASSERT(sc); 1288 1289 mii_tick(mii); 1290 if ((sc->sc_flags & AXE_FLAG_LINK) == 0) { 1291 axe_miibus_statchg(ue->ue_dev); 1292 if ((sc->sc_flags & AXE_FLAG_LINK) != 0) 1293 axe_start(ue); 1294 } 1295 } 1296 1297 static void 1298 axe_start(struct usb_ether *ue) 1299 { 1300 struct axe_softc *sc = uether_getsc(ue); 1301 1302 /* 1303 * start the USB transfers, if not already started: 1304 */ 1305 usbd_transfer_start(sc->sc_xfer[AXE_BULK_DT_RD]); 1306 usbd_transfer_start(sc->sc_xfer[AXE_BULK_DT_WR]); 1307 } 1308 1309 static void 1310 axe_csum_cfg(struct usb_ether *ue) 1311 { 1312 struct axe_softc *sc; 1313 struct ifnet *ifp; 1314 uint16_t csum1, csum2; 1315 1316 sc = uether_getsc(ue); 1317 AXE_LOCK_ASSERT(sc); 1318 1319 if ((sc->sc_flags & AXE_FLAG_772B) != 0) { 1320 ifp = uether_getifp(ue); 1321 csum1 = 0; 1322 csum2 = 0; 1323 if ((ifp->if_capenable & IFCAP_TXCSUM) != 0) 1324 csum1 |= AXE_TXCSUM_IP | AXE_TXCSUM_TCP | 1325 AXE_TXCSUM_UDP; 1326 axe_cmd(sc, AXE_772B_CMD_WRITE_TXCSUM, csum2, csum1, NULL); 1327 csum1 = 0; 1328 csum2 = 0; 1329 if ((ifp->if_capenable & IFCAP_RXCSUM) != 0) 1330 csum1 |= AXE_RXCSUM_IP | AXE_RXCSUM_IPVE | 1331 AXE_RXCSUM_TCP | AXE_RXCSUM_UDP | AXE_RXCSUM_ICMP | 1332 AXE_RXCSUM_IGMP; 1333 axe_cmd(sc, AXE_772B_CMD_WRITE_RXCSUM, csum2, csum1, NULL); 1334 } 1335 } 1336 1337 static void 1338 axe_init(struct usb_ether *ue) 1339 { 1340 struct axe_softc *sc = uether_getsc(ue); 1341 struct ifnet *ifp = uether_getifp(ue); 1342 int rxmode; 1343 1344 AXE_LOCK_ASSERT(sc); 1345 1346 1347 if ((ifp->if_flags & IFF_RUNNING) != 0) 1348 return; 1349 1350 /* Cancel pending I/O */ 1351 axe_stop(ue); 1352 1353 axe_reset(sc); 1354 1355 /* Set MAC address and transmitter IPG values. */ 1356 if (AXE_IS_178_FAMILY(sc)) { 1357 axe_cmd(sc, AXE_178_CMD_WRITE_NODEID, 0, 0, IF_LLADDR(ifp)); 1358 axe_cmd(sc, AXE_178_CMD_WRITE_IPG012, sc->sc_ipgs[2], 1359 (sc->sc_ipgs[1] << 8) | (sc->sc_ipgs[0]), NULL); 1360 } else { 1361 axe_cmd(sc, AXE_172_CMD_WRITE_NODEID, 0, 0, IF_LLADDR(ifp)); 1362 axe_cmd(sc, AXE_172_CMD_WRITE_IPG0, 0, sc->sc_ipgs[0], NULL); 1363 axe_cmd(sc, AXE_172_CMD_WRITE_IPG1, 0, sc->sc_ipgs[1], NULL); 1364 axe_cmd(sc, AXE_172_CMD_WRITE_IPG2, 0, sc->sc_ipgs[2], NULL); 1365 } 1366 1367 if (AXE_IS_178_FAMILY(sc)) { 1368 sc->sc_flags &= ~(AXE_FLAG_STD_FRAME | AXE_FLAG_CSUM_FRAME); 1369 if ((sc->sc_flags & AXE_FLAG_772B) != 0) { 1370 sc->sc_lenmask = AXE_CSUM_HDR_LEN_MASK; 1371 sc->sc_flags |= AXE_FLAG_CSUM_FRAME; 1372 } else { 1373 sc->sc_lenmask = AXE_HDR_LEN_MASK; 1374 sc->sc_flags |= AXE_FLAG_STD_FRAME; 1375 } 1376 } 1377 1378 /* Configure TX/RX checksum offloading. */ 1379 axe_csum_cfg(ue); 1380 1381 if (sc->sc_flags & AXE_FLAG_772B) { 1382 /* AX88772B uses different maximum frame burst configuration. */ 1383 axe_cmd(sc, AXE_772B_CMD_RXCTL_WRITE_CFG, 1384 ax88772b_mfb_table[AX88772B_MFB_16K].threshold, 1385 ax88772b_mfb_table[AX88772B_MFB_16K].byte_cnt, NULL); 1386 } 1387 1388 /* Enable receiver, set RX mode. */ 1389 rxmode = (AXE_RXCMD_MULTICAST | AXE_RXCMD_ENABLE); 1390 if (AXE_IS_178_FAMILY(sc)) { 1391 if (sc->sc_flags & AXE_FLAG_772B) { 1392 /* 1393 * Select RX header format type 1. Aligning IP 1394 * header on 4 byte boundary is not needed when 1395 * checksum offloading feature is not used 1396 * because we always copy the received frame in 1397 * RX handler. When RX checksum offloading is 1398 * active, aligning IP header is required to 1399 * reflect actual frame length including RX 1400 * header size. 1401 */ 1402 rxmode |= AXE_772B_RXCMD_HDR_TYPE_1; 1403 if ((ifp->if_capenable & IFCAP_RXCSUM) != 0) 1404 rxmode |= AXE_772B_RXCMD_IPHDR_ALIGN; 1405 } else { 1406 /* 1407 * Default Rx buffer size is too small to get 1408 * maximum performance. 1409 */ 1410 rxmode |= AXE_178_RXCMD_MFB_16384; 1411 } 1412 } else { 1413 rxmode |= AXE_172_RXCMD_UNICAST; 1414 } 1415 1416 /* If we want promiscuous mode, set the allframes bit. */ 1417 if (ifp->if_flags & IFF_PROMISC) 1418 rxmode |= AXE_RXCMD_PROMISC; 1419 1420 if (ifp->if_flags & IFF_BROADCAST) 1421 rxmode |= AXE_RXCMD_BROADCAST; 1422 1423 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, rxmode, NULL); 1424 1425 /* Load the multicast filter. */ 1426 axe_setmulti(ue); 1427 1428 usbd_xfer_set_stall(sc->sc_xfer[AXE_BULK_DT_WR]); 1429 1430 1431 ifp->if_flags |= IFF_RUNNING; 1432 1433 /* Switch to selected media. */ 1434 axe_ifmedia_upd(ifp); 1435 } 1436 1437 static void 1438 axe_setpromisc(struct usb_ether *ue) 1439 { 1440 struct axe_softc *sc = uether_getsc(ue); 1441 struct ifnet *ifp = uether_getifp(ue); 1442 uint16_t rxmode; 1443 1444 axe_cmd(sc, AXE_CMD_RXCTL_READ, 0, 0, &rxmode); 1445 1446 rxmode = le16toh(rxmode); 1447 1448 if (ifp->if_flags & IFF_PROMISC) { 1449 rxmode |= AXE_RXCMD_PROMISC; 1450 } else { 1451 rxmode &= ~AXE_RXCMD_PROMISC; 1452 } 1453 1454 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, rxmode, NULL); 1455 1456 axe_setmulti(ue); 1457 } 1458 1459 static void 1460 axe_stop(struct usb_ether *ue) 1461 { 1462 struct axe_softc *sc = uether_getsc(ue); 1463 struct ifnet *ifp = uether_getifp(ue); 1464 1465 AXE_LOCK_ASSERT(sc); 1466 1467 1468 ifp->if_flags &= ~IFF_RUNNING; 1469 ifq_clr_oactive(&ifp->if_snd); 1470 1471 sc->sc_flags &= ~AXE_FLAG_LINK; 1472 1473 /* 1474 * stop all the transfers, if not already stopped: 1475 */ 1476 usbd_transfer_stop(sc->sc_xfer[AXE_BULK_DT_WR]); 1477 usbd_transfer_stop(sc->sc_xfer[AXE_BULK_DT_RD]); 1478 } 1479 1480 static int 1481 axe_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data, struct ucred *uc) 1482 { 1483 struct usb_ether *ue = ifp->if_softc; 1484 struct axe_softc *sc; 1485 struct ifreq *ifr; 1486 int error, mask, reinit; 1487 1488 sc = uether_getsc(ue); 1489 ifr = (struct ifreq *)data; 1490 error = 0; 1491 reinit = 0; 1492 if (cmd == SIOCSIFCAP) { 1493 AXE_LOCK(sc); 1494 mask = ifr->ifr_reqcap ^ ifp->if_capenable; 1495 if ((mask & IFCAP_TXCSUM) != 0 && 1496 (ifp->if_capabilities & IFCAP_TXCSUM) != 0) { 1497 ifp->if_capenable ^= IFCAP_TXCSUM; 1498 if ((ifp->if_capenable & IFCAP_TXCSUM) != 0) 1499 ifp->if_hwassist |= AXE_CSUM_FEATURES; 1500 else 1501 ifp->if_hwassist &= ~AXE_CSUM_FEATURES; 1502 reinit++; 1503 } 1504 if ((mask & IFCAP_RXCSUM) != 0 && 1505 (ifp->if_capabilities & IFCAP_RXCSUM) != 0) { 1506 ifp->if_capenable ^= IFCAP_RXCSUM; 1507 reinit++; 1508 } 1509 if (reinit > 0 && ifp->if_flags & IFF_RUNNING) 1510 ifp->if_flags &= ~IFF_RUNNING; 1511 else 1512 reinit = 0; 1513 AXE_UNLOCK(sc); 1514 if (reinit > 0) 1515 uether_init(ue); 1516 } else 1517 error = uether_ioctl(ifp, cmd, data, uc); 1518 1519 return (error); 1520 } 1521