1# 2# LINT64 -- config file for checking all the sources, tries to pull in 3# as much of the source tree as it can. 4# 5# $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $ 6# 7# See the kernconf(5) manual page for more information on the format of 8# this file. 9# 10# NB: You probably don't want to try running a kernel built from this 11# file. Instead, you should start from X86_64_GENERIC, and add options 12# from this file as required. 13# 14 15# These directives are mandatory. The machine directive specifies the 16# platform and the machine_arch directive specifies the cpu architecture. 17# 18platform pc64 19machine x86_64 20machine_arch x86_64 21 22# 23# This is the mandatory ``identification'' of the kernel. Usually this should 24# be the same as the name of your kernel. 25# 26ident LINT64 27 28# 29# The `maxusers' parameter controls the static sizing of a number of 30# internal system tables by a formula defined in subr_param.c. Setting 31# maxusers to 0 will cause the system to auto-size based on physical 32# memory. 33# 34maxusers 10 35 36# 37# The `makeoptions' parameter allows variables to be passed to the 38# generated Makefile in the build area. 39# 40# CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS} 41# after most other flags. Here we use it to inhibit use of non-optimal 42# gcc builtin functions (e.g., memcmp). 43# 44# DEBUG happens to be magic. 45# The following is equivalent to 'config -g KERNELNAME' and creates 46# 'kernel.debug' compiled with -g debugging as well as a normal 47# 'kernel'. Use 'make install.debug' to install the debug kernel 48# but that isn't normally necessary as the debug symbols are not loaded 49# by the kernel and are not useful there anyway. 50# 51# KERNEL can be overridden so that you can change the default name of your 52# kernel. 53# 54# MODULES_OVERRIDE can be used to limit modules built to a specific list. 55# 56# INSTALLSTRIPPED can be set to cause installkernel to install stripped 57# kernels and modules rather than a kernel and modules with debug symbols. 58# 59# INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be 60# installed, but to strip the installed modules. 61# 62makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc. 63#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols 64#makeoptions KERNEL=foo #Build kernel "foo" and install "/foo" 65# Only build those parts of the sound system I need. 66#makeoptions MODULES_OVERRIDE="sound/snd sound/pcm" 67#makeoptions INSTALLSTRIPPED=1 68#makeoptions INSTALLSTRIPPEDMODULES=1 69 70# 71# Certain applications can grow to be larger than the 128M limit 72# that DragonFly initially imposes. Below are some options to 73# allow that limit to grow to 256MB, and can be increased further 74# with changing the parameters. MAXDSIZ is the maximum that the 75# limit can be set to, and the DFLDSIZ is the default value for 76# the limit. MAXSSIZ is the maximum that the stack limit can be 77# set to. You might want to set the default lower than the max, 78# and explicitly set the maximum with a shell command for processes 79# that regularly exceed the limit like INND. 80# 81options MAXDSIZ="(256*1024*1024)" 82options MAXSSIZ="(256*1024*1024)" 83options DFLDSIZ="(256*1024*1024)" 84 85# 86# BLKDEV_IOSIZE sets the default block size used in user block 87# device I/O. Note that this value will be overridden by the label 88# when specifying a block device from a label with a non-0 89# partition blocksize. The default is PAGE_SIZE. 90# 91options BLKDEV_IOSIZE=8192 92 93# This allows you to actually store this configuration file into 94# the kernel binary itself, where it may be later read by saying: 95# strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL 96# 97options INCLUDE_CONFIG_FILE # Include this file in kernel 98 99# 100# The root device and filesystem type can be compiled in; 101# this provides a fallback option if the root device cannot 102# be correctly guessed by the bootstrap code, or an override if 103# the RB_DFLTROOT flag (-r) is specified when booting the kernel. 104# 105options ROOTDEVNAME=\"ufs:da0s2e\" 106 107##################################################################### 108# CPU OPTIONS 109 110# cpu is mandatory 111# 112cpu HAMMER_CPU 113 114# 115# Options for CPU features. 116# 117# CPU_DISABLE_AVX disables AVX instruction set. 118# 119options CPU_DISABLE_AVX 120 121# 122# These three options provide support for System V Interface 123# Definition-style interprocess communication, in the form of shared 124# memory, semaphores, and message queues, respectively. 125# 126# System V shared memory and tunable parameters 127options SHMMIN=2 # min shared memory segment size (bytes) 128options SHMMNI=33 # max number of shared memory identifiers 129options SHMSEG=9 # max shared memory segments per process 130 131# System V semaphores and tunable parameters 132options SEMMAP=31 # amount of entries in semaphore map 133options SEMMNI=11 # number of semaphore identifiers in the system 134options SEMMNS=61 # number of semaphores in the system 135options SEMMNU=31 # number of undo structures in the system 136options SEMMSL=61 # max number of semaphores per id 137options SEMOPM=101 # max number of operations per semop call 138options SEMUME=11 # max number of undo entries per process 139 140# System V message queues and tunable parameters 141options MSGMNB=2049 # max characters per message queue 142options MSGMNI=41 # max number of message queue identifiers 143options MSGSEG=2049 # max number of message segments in the system 144options MSGSSZ=16 # size of a message segment MUST be power of 2 145options MSGTQL=41 # max amount of messages in the system 146 147##################################################################### 148# DEBUGGING OPTIONS 149 150# 151# Enable the kernel debugger. 152# 153options DDB 154 155# 156# Print a stack trace on kernel panic. 157# 158options DDB_TRACE 159 160# 161# Don't drop into DDB for a panic. Intended for unattended operation 162# where you may want to drop to DDB from the console, but still want 163# the machine to recover from a panic 164# 165options DDB_UNATTENDED 166 167# 168# If using GDB remote mode to debug the kernel, there's a non-standard 169# extension to the remote protocol that can be used to use the serial 170# port as both the debugging port and the system console. It's non- 171# standard and you're on your own if you enable it. See also the 172# "remotechat" variables in the DragonFly specific version of gdb. 173# 174options GDB_REMOTE_CHAT 175 176# 177# KTRACE enables the system-call tracing facility ktrace(2). 178# 179options KTRACE #kernel tracing 180 181# 182# The INVARIANTS option is used in a number of source files to enable 183# extra sanity checking of internal structures. This support is not 184# enabled by default because of the extra time it would take to check 185# for these conditions, which can only occur as a result of 186# programming errors. 187# 188options INVARIANTS 189 190# 191# The DIAGNOSTIC option is used to enable extra debugging information 192# from some parts of the kernel. As this makes everything more noisy, 193# it is disabled by default. 194# 195options DIAGNOSTIC 196 197# 198# SYSCTL_DEBUG enables a 'sysctl' debug tree that can be used to dump the 199# contents of the registered sysctl nodes on the console. It is disabled by 200# default because it generates excessively verbose console output that can 201# interfere with serial console operation. 202# 203options SYSCTL_DEBUG 204 205# 206# NO_SYSCTL_DESCR prevents sysctl descriptions from being compiled in 207# 208#options NO_SYSCTL_DESCR 209 210# 211# This option let some drivers co-exist that can't co-exist in a running 212# system. This is used to be able to compile all kernel code in one go for 213# quality assurance purposes (like this file, which the option takes it name 214# from.) 215# 216options COMPILING_LINT 217 218 219# XXX - this doesn't belong here. 220# Allow ordinary users to take the console - this is useful for X. 221options UCONSOLE 222 223##################################################################### 224# NETWORKING OPTIONS 225 226# 227# Protocol families: 228# Only the INET (Internet) family is officially supported in DragonFly. 229# 230options INET #Internet communications protocols 231options INET6 #IPv6 communications protocols 232 233options MPLS #Multi-Protocol Label Switching 234 235# 236# SMB/CIFS requester 237# NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV 238# options. 239options NETSMB #SMB/CIFS requester 240 241# mchain library. It can be either loaded as KLD or compiled into kernel 242options LIBMCHAIN #mbuf management library 243 244# netgraph(4). Enable the base netgraph code with the NETGRAPH option. 245# Individual node types can be enabled with the corresponding option 246# listed below; however, this is not strictly necessary as netgraph 247# will automatically load the corresponding KLD module if the node type 248# is not already compiled into the kernel. Each type below has a 249# corresponding man page, e.g., ng_async(4). 250options NETGRAPH #netgraph(4) system 251options NETGRAPH_ASYNC 252options NETGRAPH_BPF 253options NETGRAPH_BRIDGE 254options NETGRAPH_CISCO 255options NETGRAPH_ECHO 256options NETGRAPH_EIFACE 257options NETGRAPH_ETHER 258options NETGRAPH_FEC 259options NETGRAPH_FRAME_RELAY 260options NETGRAPH_HOLE 261options NETGRAPH_IFACE 262options NETGRAPH_KSOCKET 263options NETGRAPH_L2TP 264options NETGRAPH_LMI 265# MPPC compression requires proprietary files (not included) 266#options NETGRAPH_MPPC_COMPRESSION 267options NETGRAPH_MPPC_ENCRYPTION 268options NETGRAPH_ONE2MANY 269options NETGRAPH_PPP 270options NETGRAPH_PPPOE 271options NETGRAPH_PPTPGRE 272options NETGRAPH_RFC1490 273options NETGRAPH_SOCKET 274options NETGRAPH_TEE 275options NETGRAPH_TTY 276options NETGRAPH_UI 277options NETGRAPH_VJC 278 279device mn # Munich32x/Falc54 Nx64kbit/sec cards. 280 281# 282# Network interfaces: 283# The `loop' pseudo-device is MANDATORY when networking is enabled. 284# The `ether' pseudo-device provides generic code to handle 285# Ethernets; it is MANDATORY when an Ethernet device driver is 286# configured. 287# The `sppp' pseudo-device serves a similar role for certain types 288# of synchronous PPP links. 289# The `sl' pseudo-device implements the Serial Line IP (SLIP) service. 290# The `bpf' pseudo-device enables the Berkeley Packet Filter. Be 291# aware of the legal and administrative consequences of enabling this 292# option. The number of devices determines the maximum number of 293# simultaneous BPF clients programs runnable. 294# The `disc' pseudo-device implements a minimal network interface, 295# which throws away all packets sent and never receives any. It is 296# included for testing purposes. This shows up as the 'ds' interface. 297# The `tun' pseudo-device implements (user-)ppp and nos-tun 298# The `gif' pseudo-device implements IPv6 over IP4 tunneling, 299# IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and 300# IPv6 over IPv6 tunneling. 301# The `gre' device implements two types of IP4 over IP4 tunneling: 302# GRE and MOBILE, as specified in the RFC1701 and RFC2004. 303# The `stf' device implements 6to4 encapsulation. 304# The `ef' pseudo-device provides support for multiple ethernet frame types 305# specified via ETHER_* options. See ef(4) for details. 306# 307pseudo-device ether #Generic Ethernet 308pseudo-device vlan 1 #VLAN support 309pseudo-device bridge #Bridging support 310pseudo-device sppp #Generic Synchronous PPP 311pseudo-device loop #Network loopback device 312pseudo-device bpf #Berkeley packet filter 313pseudo-device disc #Discard device (ds0, ds1, etc) 314pseudo-device tap #Ethernet tunnel network interface 315pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8)) 316pseudo-device sl 2 #Serial Line IP 317pseudo-device gre #IP over IP tunneling 318 319# for IPv6 320pseudo-device gif #IPv6 and IPv4 tunneling 321pseudo-device stf #6to4 IPv6 over IPv4 encapsulation 322 323# NetBSD Virtual Machine Monitor 324pseudo-device nvmm 325 326# 327# Internet family options: 328# 329# MROUTING enables the kernel multicast packet forwarder, which works 330# with mrouted(8) (from dports). 331# 332# PIM enables Protocol Independent Multicast in the kernel. 333# Requires MROUTING enabled. 334# 335# IPFIREWALL enables support for IP firewall construction, in 336# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends 337# logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT 338# limits the number of times a matching entry can be logged. 339# 340# WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any" 341# and if you do not add other rules during startup to allow access, 342# YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open 343# in /etc/rc.conf when first enabling this feature, then refining the 344# firewall rules in /etc/rc.firewall after you've tested that the new kernel 345# feature works properly. 346# 347# IPFIREWALL3 is based on a newer version of FreeBSD's ipfw2, along with 348# some enhancements. See ipfw3(4). 349# 350# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to 351# allow everything. Use with care, if a cracker can crash your 352# firewall machine, they can get to your protected machines. However, 353# if you are using it as an as-needed filter for specific problems as 354# they arise, then this may be for you. Changing the default to 'allow' 355# means that you won't get stuck if the kernel and /sbin/ipfw binary get 356# out of sync. 357# 358# IPDIVERT enables the divert IP sockets, used by ``ipfw divert'' 359# 360# IPSTEALTH enables code to support stealth forwarding (i.e., forwarding 361# packets without touching the ttl). This can be useful to hide firewalls 362# from traceroute and similar tools. 363# 364# TCPDEBUG is undocumented. 365# 366# ICMPPRINTFS enables ICMP to do extra debug prints. 367# 368options MROUTING # Multicast routing 369options PIM # Protocol Independent Multicast 370options IPFIREWALL #firewall 371options IPFIREWALL_DEBUG #debug prints 372options IPFIREWALL_VERBOSE #enable logging to syslogd(8) 373options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity 374options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default 375options IPV6FIREWALL #firewall for IPv6 376options IPV6FIREWALL_VERBOSE 377options IPV6FIREWALL_VERBOSE_LIMIT=100 378options IPV6FIREWALL_DEFAULT_TO_ACCEPT 379options IPDIVERT #divert sockets 380options IPSTEALTH #support for stealth forwarding 381options TCPDEBUG 382options ICMPPRINTFS 383 384options IPFIREWALL3 385 386device pf 387device pflog 388 389#CARP 390pseudo-device carp 391options CARP 392 393# Link aggregation interface. 394pseudo-device lagg 395 396# The MBUF_STRESS_TEST option enables options which create 397# various random failures / extreme cases related to mbuf 398# functions. See the mbuf(9) manpage for a list of available 399# test cases. 400options MBUF_STRESS_TEST 401 402# Statically link in accept filters 403options ACCEPT_FILTER_DATA 404options ACCEPT_FILTER_HTTP 405 406# TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are 407# carried in TCP option 19. 408# This is enabled on a per-socket basis using the TCP_SIGNATURE_ENABLE 409# socket option. 410# This requires the use of 'device crypto' or 'device cryptodev'. 411# 412# XXX disabled for now until building with it is fixed, which broke 413# after removing IPsec. 414# 415#options TCP_SIGNATURE #include support for RFC 2385 416 417# 418# TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This 419# prevents nmap et al. from identifying the TCP/IP stack, but breaks support 420# for RFC1644 extensions and is not recommended for web servers. 421# 422options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN 423 424# ICMP_BANDLIM enables icmp error response bandwidth limiting. You 425# typically want this option as it will help protect the machine from 426# D.O.S. packet attacks. 427# 428options ICMP_BANDLIM 429 430# DUMMYNET enables the "dummynet" bandwidth limiter. You need 431# IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info. 432# 433options DUMMYNET 434options DUMMYNET_DEBUG 435 436# IFPOLL_ENABLE adds support for mixed interrupt-polling handling 437# of network device drivers, which has significant benefits in terms 438# of robustness to overloads and responsivity, as well as permitting 439# accurate scheduling of the CPU time between kernel network processing 440# and other activities. The drawback is a moderate (up to 1/pollhz seconds) 441# potential increase in response times. See polling(4) for further details. 442# 443# IFPOLL_ENABLE adds hardware queues' based polling 444options IFPOLL_ENABLE 445 446##################################################################### 447# FILESYSTEM OPTIONS 448 449# 450# Only the root, /usr, and /tmp filesystems need be statically 451# compiled; everything else will be automatically loaded at mount 452# time. (Exception: the UFS family --- FFS, and MFS --- 453# cannot currently be demand-loaded.) Some people still prefer 454# to statically compile other filesystems as well. 455# 456 457# One of these is mandatory: 458options FFS #Fast filesystem 459options MFS #Memory filesystem 460options NFS #Network filesystem 461 462# The rest are optional: 463#options NFS_NOSERVER #Disable the NFS-server code. 464options AUTOFS #Automounter filesystem 465options CD9660 #ISO 9660 filesystem 466options FUSE #FUSE support module 467options HAMMER #HAMMER filesystem 468options HAMMER2 #HAMMER2 filesystem 469options HPFS #OS/2 File system 470options MSDOSFS #MS DOS filesystem 471options NTFS #NT filesystem 472options NULLFS #NULL filesystem 473options PROCFS #Process filesystem 474options SMBFS #SMB/CIFS filesystem 475options TMPFS #Temporary filesystem 476options UDF #UDF filesystem 477 478# The xFS_ROOT options REQUIRE the associated ``options xFS'' 479options NFS_ROOT #NFS usable as root device 480 481# Soft updates is technique for improving UFS filesystem speed and 482# making abrupt shutdown less risky. 483options SOFTUPDATES 484 485# Directory hashing improves the speed of operations on very large 486# directories at the expense of some memory. 487options UFS_DIRHASH 488 489# Make space in the kernel for a root filesystem on a md device. 490# Define to the number of kilobytes to reserve for the filesystem. 491options MD_ROOT_SIZE=10 492 493# Make the md device a potential root device, either with preloaded 494# images of type mfs_root or md_root. 495options MD_ROOT 496 497# Specify double the default maximum size for malloc(9)-backed md devices. 498options MD_NSECT=40000 499 500# Allow this many swap-devices. 501# 502# In order to manage swap, the system must reserve bitmap space that 503# scales with the largest mounted swap device multiplied by NSWAPDEV, 504# regardless of whether other swap devices exist or not. So it 505# is not a good idea to make this value too large. 506options NSWAPDEV=5 507 508# Disk quotas are supported when this option is enabled. 509options QUOTA #enable disk quotas 510 511# If you are running a machine just as a fileserver for PC and MAC 512# users, e.g. using SAMBA, you may consider setting this option 513# and keeping all those users' directories on a filesystem that is 514# mounted with the suiddir option. This gives new files the same 515# ownership as the directory (similar to group). It's a security hole 516# if you let these users run programs, so confine it to file-servers 517# (but it'll save you lots of headaches in those cases). Root owned 518# directories are exempt and X bits are cleared. The suid bit must be 519# set on the directory as well; see chmod(1) PC owners can't see/set 520# ownerships so they keep getting their toes trodden on. This saves 521# you all the support calls as the filesystem it's used on will act as 522# they expect: "It's my dir so it must be my file". 523# 524options SUIDDIR 525 526# NFS options: 527options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec 528options NFS_MAXATTRTIMO=60 529options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec 530options NFS_MAXDIRATTRTIMO=60 531options NFS_GATHERDELAY=10 # Default write gather delay (msec) 532options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this 533options NFS_WDELAYHASHSIZ=16 # and with this 534options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this 535options NFS_DEBUG # Enable NFS Debugging 536 537# NTFS options: 538options NTFS_DEBUG 539 540# MSDOSFS options: 541options MSDOSFS_DEBUG # Enable MSDOSFS Debugging 542 543# 544# Add support for the EXT2FS filesystem of Linux fame. Be a bit 545# careful with this - the ext2fs code has a tendency to lag behind 546# changes and not be exercised very much, so mounting read/write could 547# be dangerous (and even mounting read only could result in panics.) 548# 549options EXT2FS 550 551# Optional character code conversion support with LIBICONV. 552# Each option requires their base file system and LIBICONV. 553options CD9660_ICONV 554options MSDOSFS_ICONV 555options NTFS_ICONV 556 557##################################################################### 558# POSIX P1003.1B 559 560# Real time extensions added in the 1993 Posix 561# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING 562 563options _KPOSIX_PRIORITY_SCHEDULING 564 565##################################################################### 566# CLOCK OPTIONS 567 568# The granularity of operation is controlled by the kernel option HZ whose 569# default value (100) means a granularity of 10ms (1s/HZ). 570# Consider, however, that reducing the granularity too much might 571# cause excessive overhead in clock interrupt processing, 572# potentially causing ticks to be missed and thus actually reducing 573# the accuracy of operation. 574 575options HZ=100 576 577##################################################################### 578# SCSI DEVICES 579 580# SCSI DEVICE CONFIGURATION 581 582# The SCSI subsystem consists of the `base' SCSI code, a number of 583# high-level SCSI device `type' drivers, and the low-level host-adapter 584# device drivers. The host adapters are listed in the ISA and PCI 585# device configuration sections below. 586# 587# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so 588# that a given bus, target, and LUN always come on line as the same 589# device unit. In earlier versions the unit numbers were assigned 590# in the order that the devices were probed on the SCSI bus. This 591# means that if you removed a disk drive, you may have had to rewrite 592# your /etc/fstab file, and also that you had to be careful when adding 593# a new disk as it may have been probed earlier and moved your device 594# configuration around. 595 596# This old behavior is maintained as the default behavior. The unit 597# assignment begins with the first non-wired down unit for a device 598# type. For example, if you wire a disk as "da3" then the first 599# non-wired disk will be assigned da4. 600 601# The syntax for wiring down devices is: 602 603# device scbus0 at ahc0 # Single bus device 604# device scbus1 at ahc1 bus 0 # Single bus device 605# device scbus3 at ahc2 bus 0 # Twin bus device 606# device scbus2 at ahc2 bus 1 # Twin bus device 607# device da0 at scbus0 target 0 unit 0 608# device da1 at scbus3 target 1 609# device da2 at scbus2 target 3 610# device sa1 at scbus1 target 6 611# device cd 612 613# "units" (SCSI logical unit number) that are not specified are 614# treated as if specified as LUN 0. 615 616# All SCSI devices allocate as many units as are required. 617 618# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI 619# configuration and doesn't have to be explicitly configured. 620 621device scbus #base SCSI code 622device ch #SCSI media changers 623device da #SCSI direct access devices (aka disks) 624device sa #SCSI tapes 625device cd #SCSI CD-ROMs 626device pass #CAM passthrough driver 627device sg #Passthrough device (linux scsi generic) 628device pt #SCSI processor type 629device ses #SCSI SES/SAF-TE driver 630device targ #SCSI Target Mode Code 631device targbh #SCSI Target Mode Blackhole Device 632 633# Options for device mapper 634device dm 635device dm_target_crypt 636device dm_target_linear 637device dm_target_striped 638device dm_target_delay 639device dm_target_flakey 640 641# Options for iSCSI 642device iscsi_initiator 643options ISCSI_INITIATOR_DEBUG=8 644 645# CAM OPTIONS: 646# debugging options: 647# -- NOTE -- If you specify one of the bus/target/lun options, you must 648# specify them all! 649# CAMDEBUG: When defined enables debugging macros 650# CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses. 651# CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets. 652# CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns. 653# CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE, 654# CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB 655# 656# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds 657# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions 658# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions 659# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter) 660# queue after a bus reset, and the number of milliseconds to 661# freeze the device queue after a bus device reset. This 662# can be changed at boot and runtime with the 663# kern.cam.scsi_delay tunable/sysctl. 664options CAMDEBUG 665options CAM_DEBUG_BUS=-1 666options CAM_DEBUG_TARGET=-1 667options CAM_DEBUG_LUN=-1 668options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB" 669options CAM_MAX_HIGHPOWER=4 670options SCSI_NO_SENSE_STRINGS 671options SCSI_NO_OP_STRINGS 672options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device 673 674# Options for the CAM CDROM driver: 675# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN 676# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only 677# enforced if there is I/O waiting for another LUN 678# The compiled in defaults for these variables are 2 and 10 seconds, 679# respectively. 680# 681# These can also be changed on the fly with the following sysctl variables: 682# kern.cam.cd.changer.min_busy_seconds 683# kern.cam.cd.changer.max_busy_seconds 684# 685options CHANGER_MIN_BUSY_SECONDS=2 686options CHANGER_MAX_BUSY_SECONDS=10 687 688# Options for the CAM sequential access driver: 689# SA_IO_TIMEOUT: Timeout for read/write/wfm operations, in minutes 690# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes 691# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes 692# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes 693# SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT. 694options SA_IO_TIMEOUT="(4)" 695options SA_SPACE_TIMEOUT="(60)" 696options SA_REWIND_TIMEOUT="(2*60)" 697options SA_ERASE_TIMEOUT="(4*60)" 698options SA_1FM_AT_EOD 699 700# Optional timeout for the CAM processor target (pt) device 701# This is specified in seconds. The default is 60 seconds. 702options SCSI_PT_DEFAULT_TIMEOUT="60" 703 704# Optional enable of doing SES passthrough on other devices (e.g., disks) 705# 706# Normally disabled because a lot of newer SCSI disks report themselves 707# as having SES capabilities, but this can then clot up attempts to build 708# build a topology with the SES device that's on the box these drives 709# are in.... 710options SES_ENABLE_PASSTHROUGH 711 712##################################################################### 713# MISCELLANEOUS DEVICES AND OPTIONS 714 715# The `pty' device usually turns out to be ``effectively mandatory'', 716# as it is required for `telnetd', `rlogind', `screen', `emacs', and 717# `xterm', among others. 718 719pseudo-device pty # Pseudo ttys 720pseudo-device gzip # Exec gzipped a.out's 721pseudo-device md # Memory/malloc disk 722pseudo-device vn # File image "disks" 723pseudo-device snp # Snoop device - to look at pty/vty/etc.. 724pseudo-device ccd 4 # Concatenated disk driver 725 726# Configuring Vinum into the kernel is not necessary, since the kld 727# module gets started automatically when vinum(8) starts. This 728# device is also untested. Use at your own risk. 729# 730# The option VINUMDEBUG must match the value set in CFLAGS 731# in src/sbin/vinum/Makefile. Failure to do so will result in 732# the following message from vinum(8): 733# 734# Can't get vinum config: Invalid argument 735# 736# see vinum(4) for more reasons not to use these options. 737pseudo-device vinum #Vinum concat/mirror/raid driver 738options VINUMDEBUG #enable Vinum debugging hooks 739 740# Kernel side iconv library 741options LIBICONV 742 743# Size of the kernel message buffer. Should be N * pagesize. 744options MSGBUF_SIZE=40960 745 746##################################################################### 747# HARDWARE DEVICE CONFIGURATION 748 749# ISA devices: 750 751# 752# Mandatory ISA devices: isa 753# 754device isa 755 756# 757# Options for `isa': 758# 759# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A 760# interrupt controller. This saves about 0.7-1.25 usec for each interrupt. 761# This option breaks suspend/resume on some portables. 762# 763# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A 764# interrupt controller. This saves about 0.7-1.25 usec for each interrupt. 765# Automatic EOI is documented not to work for the slave with the 766# original i8259A, but it works for some clones and some integrated 767# versions. 768# 769# MAXMEM specifies the amount of RAM on the machine; if this is not 770# specified, DragonFly will first read the amount of memory from the CMOS 771# RAM, so the amount of memory will initially be limited to 64MB or 16MB 772# depending on the BIOS. If the BIOS reports 64MB, a memory probe will 773# then attempt to detect the installed amount of RAM. If this probe 774# fails to detect >64MB RAM you will have to use the MAXMEM option. 775# The amount is in kilobytes, so for a machine with 128MB of RAM, it would 776# be 131072 (128 * 1024). 777# 778# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to 779# reset the CPU for reboot. This is needed on some systems with broken 780# keyboard controllers. 781 782options AUTO_EOI_1 783#options AUTO_EOI_2 784options MAXMEM="(128*1024)" 785#options BROKEN_KEYBOARD_RESET 786 787# Enable support for the kernel PLL to use an external PPS signal, 788# under supervision of [x]ntpd(8) 789# More info in ntpd documentation: http://www.eecis.udel.edu/~ntp 790 791options PPS_SYNC 792 793# The keyboard controller; it controls the keyboard and the PS/2 mouse. 794device atkbdc0 at isa? port IO_KBD 795 796# The AT keyboard 797device atkbd0 at atkbdc? irq 1 798 799# Options for atkbd: 800options ATKBD_DFLT_KEYMAP # specify the built-in keymap 801makeoptions ATKBD_DFLT_KEYMAP="jp.106" 802 803# These options are valid for other keyboard drivers as well. 804options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap 805options KBD_INSTALL_CDEV # install a CDEV entry in /dev 806 807# `flags' for atkbd: 808# 0x01 Force detection of keyboard, else we always assume a keyboard 809# 0x02 Don't reset keyboard, useful for some newer ThinkPads 810# 0x03 Force detection and avoid reset, might help with certain 811# dockingstations 812# 0x04 Old-style (XT) keyboard support, useful for older ThinkPads 813 814# PS/2 mouse 815device psm0 at atkbdc? irq 12 816 817# Options for psm: 818options PSM_HOOKRESUME #hook the system resume event, useful 819 #for some laptops 820options PSM_RESETAFTERSUSPEND #reset the device at the resume event 821 822device kbdmux # keyboard multiplexer 823 824# The video card driver. 825device vga0 at isa? 826 827# Options for vga: 828options VGA_DEBUG=2 # enable VGA debug output 829 830# If you experience problems switching back to 80x25 (or a derived mode), 831# the following option might help. 832#options VGA_KEEP_POWERON_MODE # use power-on settings for 80x25 833 834# If you can dispense with some vga driver features, you may want to 835# use the following options to save some memory. 836#options VGA_NO_FONT_LOADING # don't save/load font 837#options VGA_NO_MODE_CHANGE # don't change video modes 838 839# The following option probably won't work with the LCD displays. 840options VGA_WIDTH90 # support 90 column modes 841 842# Splash screen at start up! Screen savers require this too. 843pseudo-device splash 844 845# The syscons console driver (sco color console compatible). 846device sc0 at nexus? 847options MAXCONS=16 # number of virtual consoles 848options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode 849options SC_DEBUG_LEVEL=5 # enable debug output 850options SC_DFLT_FONT # compile font in 851makeoptions SC_DFLT_FONT=cp850 852options SC_DISABLE_DDBKEY # disable `debug' key 853options SC_DISABLE_REBOOT # disable reboot key sequence 854options SC_HISTORY_SIZE=200 # number of history buffer lines 855options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor 856options SC_PIXEL_MODE # add support for the raster text mode 857 858# The following options will let you change the default colors of syscons. 859options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)" 860options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)" 861options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)" 862options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)" 863options SC_BORDER_COLOR="FG_BLACK" 864 865# If you have a two button mouse, you may want to add the following option 866# to use the right button of the mouse to paste text. 867options SC_TWOBUTTON_MOUSE 868 869# You can selectively disable features in syscons. 870#options SC_NO_CUTPASTE 871#options SC_NO_FONT_LOADING 872#options SC_NO_HISTORY 873#options SC_NO_SYSMOUSE 874 875# 876# SCSI host adapters 877# 878# adv: All Narrow SCSI bus AdvanSys controllers. 879# adw: Second Generation AdvanSys controllers including the ADV940UW. 880# bt: Most Buslogic controllers 881# 882# Note that the order is important in order for Buslogic cards to be 883# probed correctly. 884# 885 886device bt 887device adv 888device adw 889 890# 891# Adaptec FSA RAID controllers, including integrated DELL controller, 892# the Dell PERC 2/QC and the HP NetRAID-4M 893# 894device aac 895options AAC_DEBUG 896device aacp # SCSI Passthrough interface (optional, CAM required) 897 898# 899# Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only 900# one entry is needed; the code will find and configure all supported 901# controllers. 902# 903device ida # Compaq Smart RAID 904device mlx # Mylex DAC960 905device amr # AMI MegaRAID 906device amrp # SCSI Passthrough interface (optional, CAM req.) 907options AMR_DEBUG=3 908device mfi # LSI MegaRAID SAS 909device mfip # LSI MegaRAID SAS passthrough, requires CAM 910options MFI_DEBUG 911 912# 913# LSI MegaRAID 6Gb/s and 12Gb/s SAS+SATA RAID controller driver 914# 915device mrsas 916 917# 918# Areca RAID (CAM is required). 919# 920device arcmsr # Areca SATA II RAID 921 922# 923# Highpoint RocketRAID 182x. 924device hptmv 925 926# 927# Highpoint RocketRAID. Supports RR172x, RR222x, RR2240, RR232x, RR2340, 928# RR2210, RR174x, RR2522, RR231x, RR230x. 929device hptrr 930 931# 932# Highpoint RocketRAID 27xx. 933device "hpt27xx" 934 935# 936# Highpoint RocketRaid 3xxx series SATA RAID 937device hptiop 938 939# 940# 3ware ATA RAID 941# 942device twe # 3ware ATA RAID 943device twa # 3ware 9000 series PATA/SATA RAID 944options TWA_DEBUG=10 # enable debug messages 945device tws # 3ware 9750 series SATA/SAS RAID 946 947# 948# IBM ServeRAID 949# 950device ips 951 952# AHCI driver, this will override NATA for AHCI devices, 953# both drivers may be included. 954# 955device ahci 956 957# NVME driver 958# 959device nvme 960 961# SiI3124/3132 driver 962# 963device sili 964 965# The 'NATA' driver supports all ATA and ATAPI devices. 966# You only need one "device nata" for it to find all 967# PCI ATA/ATAPI devices on modern machines. 968# 969device nata 970device natadisk # ATA disk drives 971device natapicd # ATAPI CD/DVD drives 972device natapifd # ATAPI floppy drives 973device natapist # ATAPI tape drives 974device natapicam # ATAPI CAM layer emulation 975device nataraid # support for ATA software RAID controllers 976 977# The following options are valid for the NATA driver: 978# 979# ATA_STATIC_ID: controller numbering is static (like the old driver) 980# else the device numbers are dynamically allocated. 981# ATA_NO_*: leave out support for the specified controller brand 982# 983options ATA_STATIC_ID 984#options ATA_NO_ACARD 985#options ATA_NO_ACERLABS 986#options ATA_NO_AHCI 987#options ATA_NO_AMD 988#options ATA_NO_CYPRESS 989#options ATA_NO_CYRIX 990#options ATA_NO_HIGHPOINT 991#options ATA_NO_INTEL 992#options ATA_NO_ITE 993#options ATA_NO_JMICRON 994#options ATA_NO_MARVELL 995#options ATA_NO_NATIONAL 996#options ATA_NO_NETCELL 997#options ATA_NO_NVIDIA 998#options ATA_NO_PROMISE 999#options ATA_NO_SERVERWORKS 1000#options ATA_NO_SILICONIMAGE 1001#options ATA_NO_SIS 1002#options ATA_NO_VIA 1003 1004# For older non-PCI systems, these are the lines to use: 1005# 1006#device nata0 at isa? port IO_WD1 irq 14 1007#device nata1 at isa? port IO_WD2 irq 15 1008 1009# 1010# Standard floppy disk controllers: `fdc' and `fd' (see fdc(4)) 1011# 1012device fdc0 at isa? port IO_FD1 irq 6 drq 2 1013# 1014# FDC_DEBUG enables floppy debugging. Since the debug output is huge, you 1015# gotta turn it actually on by setting the variable fd_debug with DDB, 1016# however. 1017options FDC_DEBUG 1018 1019device fd0 at fdc0 drive 0 1020device fd1 at fdc0 drive 1 1021 1022# LMC/SBE LMC1504 quad T1/E1 driver 1023# 1024device musycc 1025 1026# 1027# sio: serial ports (see sio(4)) 1028 1029device sio0 at isa? port IO_COM1 flags 0x10 irq 4 1030 1031# 1032# `flags' for serial drivers that support consoles (only for sio now): 1033# 0x10 enable console support for this unit. The other console flags 1034# are ignored unless this is set. Enabling console support does 1035# not make the unit the preferred console - boot with -h or set 1036# the 0x20 flag for that. Currently, at most one unit can have 1037# console support; the first one (in config file order) with 1038# this flag set is preferred. Setting this flag for sio0 gives 1039# the old behaviour. 1040# 0x20 force this unit to be the console (unless there is another 1041# higher priority console). This replaces the COMCONSOLE option. 1042# 0x40 reserve this unit for low level console operations. Do not 1043# access the device in any normal way. 1044# 0x80 use this port for serial line gdb support in ddb. 1045# 1046 1047# Options for serial drivers that support consoles (only for sio now): 1048options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to 1049 #DDB, if available. 1050options CONSPEED=115200 # speed for serial console 1051 # (default 9600) 1052 1053# Solaris implements a new BREAK which is initiated by a character 1054# sequence CR ~ ^b which is similar to a familiar pattern used on 1055# Sun servers by the Remote Console. 1056options ALT_BREAK_TO_DEBUGGER 1057 1058# Options for sio: 1059options COM_ESP #code for Hayes ESP 1060options COM_MULTIPORT #code for some cards with shared IRQs 1061 1062# Other flags for sio that aren't documented in the man page. 1063# 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for 1064# ST16650A-compatible UARTs. 1065 1066# PCI Universal Communications driver 1067# Supports various single and multi port PCI serial cards. Maybe later 1068# also the parallel ports on combination serial/parallel cards. New cards 1069# can be added in src/sys/dev/misc/puc/pucdata.c. 1070device puc 1071 1072# 1073# Network interfaces: `is', `lnc' 1074# 1075# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960) 1076# sbsh: Granch SBNI16 SHDSL modem PCI adapters 1077# vmx: VMware VMXNET3 Ethernet (BSD open source) 1078# wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both 1079# the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA 1080# bridge with a PCMCIA adapter plugged into it. 1081# xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller. 1082# 1083device lnc 1084device sln 1085device sn 1086 1087# Wlan support is mandatory for some wireless LAN devices. 1088options IEEE80211_DEBUG #enable debugging msgs 1089options IEEE80211_SUPPORT_MESH #enable 802.11s D3.0 support 1090options IEEE80211_SUPPORT_TDMA #enable TDMA support 1091device wlan # 802.11 support 1092device wlan_acl # 802.11 MAC-based access control for AP 1093device wlan_ccmp # 802.11 CCMP support 1094device wlan_tkip # 802.11 TKIP support 1095device wlan_wep # 802.11 WEP support 1096device wlan_xauth # 802.11 WPA or 802.1x authentication for AP 1097device wlan_amrr # 802.11 AMRR TX rate control algorithm 1098device ath # Atheros AR521x 1099options AH_AR5416_INTERRUPT_MITIGATION 1100options AH_ASSERT 1101options AH_DEBUG 1102options AH_INTERRUPT_DEBUGGING 1103options AH_MAXCHAN=96 1104options AH_NEED_DESC_SWAP 1105options AH_PRIVATE_DIAG 1106options AH_RXCFG_SDMAMW_4BYTES 1107options AH_SUPPORT_AR5416 1108options AH_SUPPORT_AR9130 1109options AH_SUPPORT_AR9330 1110options AH_SUPPORT_AR9340 1111options AH_USE_INIPDGAIN 1112device ath_hal # Atheros Hardware Access Layer 1113#device ath_rate_amrr # Atheros AMRR TX rate control algorithm 1114#device ath_rate_onoe # Atheros Onoe TX rate control algorithm 1115device ath_rate_sample # Atheros Sample TX rate control algorithm 1116options ATH_DEBUG # turn on debugging output (see hw.ath.debug) 1117options ATH_DIAGAPI # diagnostic interface to the HAL 1118options ATH_ENABLE_DFS 1119options ATH_KTR_INTR_DEBUG 1120device siba_bwn # Sonic Inc. Silicon Backplane needed for bwn 1121options SIBA_DEBUG # turn on debugging output 1122device bwn # Broadcom BCM43xx NICs using v4 firmware 1123options BWN_DEBUG # turn on debugging output 1124options BWN_RXRING_SLOTS=128 # number of RX slots to allocate 1125options BWN_TXRING_SLOTS=128 # number of TX slots to allocate 1126device iwi # Intel PRO/Wireless 2200BG/2915ABG 1127device iwm # Intel Dual Band Wireless AC 316x/726x/826x 1128options IWM_DEBUG # turn on debugging output 1129device iwn # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050 1130options IWN_DEBUG # turn on debugging output 1131device wi # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS 1132device xe # Xircom PCMCIA 1133device ral # Ralink Technology 802.11 wireless NIC 1134device wpi 1135options WPI_DEBUG # turn on debugging output 1136 1137# IEEE 802.11 adapter firmware modules 1138 1139# iwifw: Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware 1140# iwmfw Intel Dual Band Wireless AC 3160/3165/3168/7260/7265/8260/8265 1141# iwnfw: Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050 1142# ralfw: Ralink Technology RT25xx and RT26xx firmware 1143# wpifw: Intel 3945ABG Wireless LAN Controller firmware 1144 1145device iwifw 1146device iwmfw 1147device iwnfw 1148device ralfw 1149device wpifw 1150 1151# Bluetooth Protocols 1152device bluetooth 1153 1154# Sound drivers 1155# 1156 1157# Basic sound card support: 1158device sound 1159# For PCI sound cards: 1160device "snd_als4000" 1161device "snd_atiixp" 1162device "snd_cmi" 1163device "snd_cs4281" 1164device "snd_emu10k1" 1165device "snd_emu10kx" 1166device "snd_envy24" 1167device "snd_envy24ht" 1168device "snd_es137x" 1169device "snd_fm801" 1170device "snd_hda" 1171device "snd_hdspe" 1172device "snd_ich" 1173device "snd_maestro" 1174device "snd_neomagic" 1175device "snd_solo" 1176device "snd_spicds" 1177device "snd_t4dwave" 1178device "snd_via8233" 1179device "snd_via82c686" 1180device "snd_vibes" 1181# USB 1182device "snd_uaudio" 1183 1184# 1185# Following options are intended for debugging/testing purposes: 1186# 1187# SND_DEBUG Enable extra debugging code that includes 1188# sanity checking and possible increase of 1189# verbosity. 1190# 1191# SND_DIAGNOSTIC Similar in a spirit of INVARIANTS/DIAGNOSTIC, 1192# zero tolerance against inconsistencies. 1193# 1194# SND_FEEDER_MULTIFORMAT By default, only 16/32 bit feeders are compiled 1195# in. This options enable most feeder converters 1196# except for 8bit. WARNING: May bloat the kernel. 1197# 1198# SND_FEEDER_FULL_MULTIFORMAT Ditto, but includes 8bit feeders as well. 1199# 1200# SND_FEEDER_RATE_HP (feeder_rate) High precision 64bit arithmetic 1201# as much as possible (the default trying to 1202# avoid it). Possible slowdown. 1203# 1204# SND_OLDSTEREO Only 2 channels are allowed, effectively 1205# disabling multichannel processing. 1206# 1207options SND_DEBUG 1208#options SND_DIAGNOSTIC 1209options SND_FEEDER_MULTIFORMAT 1210options SND_FEEDER_FULL_MULTIFORMAT 1211options SND_FEEDER_RATE_HP 1212options SND_OLDSTEREO 1213 1214# 1215# Miscellaneous hardware: 1216# 1217# bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board 1218# coremctl: Intel Core/E3 memory controller (required by ecc(4) and memtemp(4)) 1219# dimm: Location inforamtion (required by ecc(4) and memtemp(4)) 1220# ecc: ECC memory controller 1221# ipmi: Intelligent Platform Management Interface 1222# joy: joystick 1223# nmdm: nullmodem terminal driver (see nmdm(4)) 1224# tpm: Trusted Platform Module 1225 1226# Notes on the Specialix SI/XIO driver: 1227# **This is NOT a Specialix supported Driver!** 1228# The host card is memory, not IO mapped. 1229# The Rev 1 host cards use a 64K chunk, on a 32K boundary. 1230# The Rev 2 host cards use a 32K chunk, on a 32K boundary. 1231# The cards can use an IRQ of 11, 12 or 15. 1232 1233device coremctl 1234device dimm 1235device ecc 1236device joy0 at isa? port IO_GAME 1237# nullmodem terminal driver 1238device nmdm 1239device tpm 1240options TPM_HARVEST # This options turns TPM into entropy source. 1241device ipmi 1242 1243# The adw driver will attempt to use memory mapped I/O for all PCI 1244# controllers that have it configured only if this option is set. 1245options ADW_ALLOW_MEMIO 1246 1247# 1248# PCI devices & PCI options: 1249# 1250# The main PCI bus device is `pci'. It provides auto-detection and 1251# configuration support for all devices on the PCI bus, using either 1252# configuration mode defined in the PCI specification. 1253 1254device pci 1255 1256# AGP GART support 1257# 1258device agp 1259 1260# 1261# AGP debugging. 1262# 1263options AGP_DEBUG 1264 1265# The `amd' device provides support for the AMD 53C974 SCSI host 1266# adapter chip as found on devices such as the Tekram DC-390(T). 1267# 1268# The `bge' device provides support for gigabit ethernet adapters 1269# based on the Broadcom BCM570x family of controllers, including the 1270# 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41, 1271# and the embedded gigE NICs on Dell PowerEdge 2550 servers. 1272# 1273# The `ncr' device provides support for the NCR 53C810 and 53C825 1274# self-contained SCSI host adapters. 1275# 1276# The `isp' device provides support for the Qlogic ISP 1020, 1040 1277# nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI, 1278# ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as 1279# the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters. 1280# 1281# The `dc' device provides support for PCI fast ethernet adapters 1282# based on the DEC/Intel 21143 and various workalikes including: 1283# the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics 1284# AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On 1285# 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II 1286# and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver 1287# replaces the old al, ax, dm, pn and mx drivers. List of brands: 1288# Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110, 1289# SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX, 1290# LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204, 1291# KNE110TX. 1292# 1293# The `de' device provides support for the Digital Equipment DC21040 1294# self-contained Ethernet adapter. 1295# 1296# The `em' device provides support for the Intel Pro/1000 Family of Gigabit 1297# adapters (82542, 82543, 82544, 82540). 1298# 1299# The `et' device provides support for the Agere ET1310 10/100/1000 PCIe 1300# adapters. 1301# 1302# The `fxp' device provides support for the Intel EtherExpress Pro/100B 1303# PCI Fast Ethernet adapters. 1304# 1305# The 'lge' device provides support for PCI gigabit ethernet adapters 1306# based on the Level 1 LXT1001 NetCellerator chipset. This includes the 1307# D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards. 1308# 1309# The 'my' device provides support for the Myson MTD80X and MTD89X PCI 1310# Fast Ethernet adapters. 1311# 1312# The 'nge' device provides support for PCI gigabit ethernet adapters 1313# based on the National Semiconductor DP83820 and DP83821 chipset. This 1314# includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante 1315# FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the 1316# LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T. 1317# 1318# The 'oce' device provides support for Emulex 10 Gbit adapters 1319# (OneConnect Ethernet). 1320# 1321# The 'pcn' device provides support for PCI fast ethernet adapters based 1322# on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+, 1323# PCnet/PRO and PCnet/Home. These were previously handled by the lnc 1324# driver (and still will be if you leave this driver out of the kernel). 1325# 1326# Te 're' device provides support for PCI GigaBit ethernet adapters based 1327# on the RealTek 8169 chipset. It also supports the 8139C+ and is the 1328# preferred driver for that chip. 1329# 1330# The 'rl' device provides support for PCI fast ethernet adapters based 1331# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults 1332# to using programmed I/O to do register accesses because memory mapped 1333# mode seems to cause severe lockups on SMP hardware. This driver also 1334# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called 1335# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek 1336# workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset 1337# and is supported by this driver, not the 'vr' driver. 1338# 1339# The 'sf' device provides support for Adaptec Duralink PCI fast 1340# ethernet adapters based on the Adaptec AIC-6915 "starfire" controller. 1341# This includes dual and quad port cards, as well as one 100baseFX card. 1342# Most of these are 64-bit PCI devices, except for one single port 1343# card which is 32-bit. 1344# 1345# The 'ste' device provides support for adapters based on the Sundance 1346# Technologies ST201 PCI fast ethernet controller. This includes the 1347# D-Link DFE-550TX. 1348# 1349# The 'sis' device provides support for adapters based on the Silicon 1350# Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller 1351# chips. 1352# 1353# The 'sk' device provides support for the SysKonnect SK-984x series 1354# PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842 1355# single port cards (single mode and multimode fiber) and the 1356# SK-9843 and SK-9844 dual port cards (also single mode and multimode). 1357# The driver will autodetect the number of ports on the card and 1358# attach each one as a separate network interface. 1359# 1360# The 'ti' device provides support for PCI gigabit ethernet NICs based 1361# on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the 1362# Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others. 1363# Note that you will probably want to bump up NMBCLUSTERS a lot to use 1364# this driver. 1365# 1366# The 'tl' device provides support for the Texas Instruments TNETE100 1367# series 'ThunderLAN' cards and integrated ethernet controllers. This 1368# includes several Compaq Netelligent 10/100 cards and the built-in 1369# ethernet controllers in several Compaq Prosignia, Proliant and 1370# Deskpro systems. It also supports several Olicom 10Mbps and 10/100 1371# boards. 1372# 1373# The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards. 1374# 1375# The `txp' device provides support for the 3Com 3cR990 "Typhoon" 1376# 10/100 adapters. 1377# 1378# The `vr' device provides support for various fast ethernet adapters 1379# based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II' 1380# chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking 1381# Technologies PN102TX, and the AOpen/Acer ALN-320. 1382# 1383# The `wb' device provides support for various fast ethernet adapters 1384# based on the Winbond W89C840F chip. Note: this is not the same as 1385# the Winbond W89C940F, which is an NE2000 clone. 1386# 1387# The `xl' device provides support for the 3Com 3c900, 3c905 and 1388# 3c905B (Fast) Etherlink XL cards and integrated controllers. This 1389# includes the integrated 3c905B-TX chips in certain Dell Optiplex and 1390# Dell Precision desktop machines and the integrated 3c905-TX chips 1391# in Dell Latitude laptop docking stations. 1392# 1393# The 'bktr' device is a PCI video capture device using the Brooktree 1394# bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a 1395# TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator, 1396# Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo. 1397# 1398# options OVERRIDE_CARD=xxx 1399# options OVERRIDE_TUNER=xxx 1400# options OVERRIDE_MSP=1 1401# options OVERRIDE_DBX=1 1402# These options can be used to override the auto detection 1403# The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h 1404# Using sysctl(8) run-time overrides on a per-card basis can be made 1405# 1406# options BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL 1407# or 1408# options BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC 1409# Specifies the default video capture mode. 1410# This is required for Dual Crystal (28&35Mhz) boards where PAL is used 1411# to prevent hangs during initialisation. eg VideoLogic Captivator PCI. 1412# 1413# options BKTR_USE_PLL 1414# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal) 1415# must enable PLL mode with this option. eg some new Bt878 cards. 1416# 1417# options BKTR_GPIO_ACCESS 1418# This enable IOCTLs which give user level access to the GPIO port. 1419# 1420# options BKTR_NO_MSP_RESET 1421# Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first 1422# 1423# options BKTR_430_FX_MODE 1424# Switch Bt878/879 cards into Intel 430FX chipset compatibility mode. 1425# 1426# options BKTR_SIS_VIA_MODE 1427# Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is 1428# needed for some old SiS and VIA chipset motherboards. 1429# This also allows Bt878/879 chips to work on old OPTi (<1997) chipset 1430# motherboards and motherboards with bad or incomplete PCI 2.1 support. 1431# As a rough guess, old = before 1998 1432# 1433# options BKTR_NEW_MSP34XX_DRIVER 1434# Use new, more complete initialization scheme for the msp34* soundchip. 1435# Should fix stereo autodetection if the old driver does only output 1436# mono sound. 1437# 1438# options BKTR_OVERRIDE_CARD=xxx 1439# options BKTR_OVERRIDE_DBX=xxx 1440# options BKTR_OVERRIDE_MSP=xxx 1441# options BKTR_OVERRIDE_TUNER=xxx 1442# These options can be used to select a specific device, regardless of 1443# the autodetection and i2c device checks (see comments in bktr_card.c). 1444# 1445device amd # AMD 53C974 (Tekram DC-390(T)) 1446device isp # Qlogic family 1447device ispfw # Firmware for QLogic HBAs 1448device mpr # LSI-Logic MPT-Fusion 3 1449device mps # LSI-Logic MPT-Fusion 2 1450device mpt # LSI '909 FC adapters 1451device ncr # NCR/Symbios Logic 1452device sym # NCR/Symbios Logic (newer chipsets) 1453device trm # Tekram DC395U/UW/F and DC315U 1454# 1455# Options for ISP 1456# 1457# ISP_TARGET_MODE - enable target mode operation 1458#options ISP_TARGET_MODE=1 1459 1460# Options used in dev/disk/sym/ (Symbios SCSI driver). 1461#options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits) 1462 # Allows the ncr to take precedence 1463 # 1 (1<<0) -> 810a, 860 1464 # 2 (1<<1) -> 825a, 875, 885, 895 1465 # 4 (1<<2) -> 895a, 896, 1510d 1466#options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885 1467 # disabled:0 (default), enabled:1 1468#options SYM_SETUP_PCI_PARITY #-PCI parity checking 1469 # disabled:0, enabled:1 (default) 1470#options SYM_SETUP_MAX_LUN #-Number of LUNs supported 1471 # default:8, range:[1..64] 1472 1473 1474# MII bus support is required for some PCI 10/100 ethernet NICs, 1475# namely those which use MII-compliant transceivers or implement 1476# transceiver control interfaces that operate like an MII. Adding 1477# "device miibus0" to the kernel config pulls in support for 1478# the generic miibus API and all of the PHY drivers, including a 1479# generic one for PHYs that aren't specifically handled by an 1480# individual driver. 1481device miibus 1482 1483# PCI Ethernet NICs that use the common MII bus controller code. 1484device ae # Attansic/Atheros L2 Fast Ethernet 1485device alc # Atheros AR8131/AR8132 1486device ale # Atheros AR8121/AR8113/AR8114 1487device age # Attansic/Atheros L1 Gigabit Ethernet 1488device bce # Broadcom NetXtreme II Gigabit Ethernet 1489device bfe # Broadcom BCM440x 10/100 Ethernet 1490device bnx # Broadcom NetXtreme 5718/57785 Gigabit Ethernet 1491device dc # DEC/Intel 21143 and various workalikes 1492device fxp # Intel EtherExpress PRO/100B (82557, 82558) 1493device my # Myson Fast Ethernet (MTD80X, MTD89X) 1494device pcn # AMD Am79C97x PCI 10/100 NICs 1495device re # RealTek 8139C+/8169 1496device rl # RealTek 8129/8139 1497device sbsh # Granch SBNI16 SHDSL modem 1498device sf # Adaptec AIC-6915 (``Starfire'') 1499device sis # Silicon Integrated Systems SiS 900/SiS 7016 1500device ste # Sundance ST201 (D-Link DFE-550TX) 1501device tl # Texas Instruments ThunderLAN 1502device tx # SMC EtherPower II (83c17x ``EPIC'') 1503device vge # VIA 612x GigE 1504device vr # VIA Rhine, Rhine II 1505device wb # Winbond W89C840F 1506device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') 1507 1508# PCI Ethernet NICs. 1509device de # DEC/Intel DC21x4x (``Tulip'') 1510device txp # 3Com 3cR990 (``Typhoon'') 1511 1512# Gigabit Ethernet NICs. 1513device bge # Broadcom BCM570x (``Tigon III'') 1514device em # Intel Pro/1000 (8254x,8257x) 1515 # Requires ig_hal 1516device emx # Intel Pro/1000 (8257{1,2,3,4}) 1517 # Requires ig_hal 1518device igb # Intel Pro/1000 (82575, 82576, 82580, i350) 1519 # Requires ig_hal 1520device ig_hal # Intel Pro/1000 hardware abstraction layer 1521device ix # Intel PRO/10GbE PCIE Ethernet Family 1522device et # Agere ET1310 10/100/1000 Ethernet 1523device lge # Level 1 LXT1001 (``Mercury'') 1524device mxge # Myricom Myri-10G 10GbE NIC 1525device mxgefw # Firmware for Myricom Myri-10G 10GbE NIC 1526device nfe # nVidia nForce2/3 MCP04/51/55 CK804 1527device nge # NatSemi DP83820 and DP83821 1528device oce # Emulex 10 GbE (OneConnect Ethernet) 1529device sk # SysKonnect GEnesis, LinkSys EG1023, D-Link 1530device ti # Alteon (``Tigon I'', ``Tigon II'') 1531device stge # Sundance/Tamarack TC9021 Gigabit Ethernet 1532device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet 1533device jme # JMicron Gigabit/Fast Ethernet 1534 1535# Brooktree driver has been ported to the new I2C framework. Thus, 1536# you'll need to have the following 3 lines in the kernel config. 1537# device smbus 1538# device iicbus 1539# device iicbb 1540# The iic and smb devices are only needed if you want to control other 1541# I2C slaves connected to the external connector of some cards. 1542# 1543device bktr 1544options BKTR_NEW_MSP34XX_DRIVER 1545 1546# WinTV PVR-250/350 driver 1547device cxm 1548 1549# 1550# PCCARD/PCMCIA 1551# 1552# pccard: pccard slots 1553# cardbus/cbb: cardbus bridge 1554device pccard 1555device cardbus 1556device cbb 1557 1558# 1559# MMC/SD 1560# 1561# mmc MMC/SD bus 1562# mmcsd MMC/SD memory card 1563# sdhci Generic PCI SD Host Controller 1564# 1565device mmc 1566device mmcsd 1567device sdhci 1568 1569# 1570# SMB bus 1571# 1572# System Management Bus support is provided by the 'smbus' device. 1573# Access to the SMBus device is via the 'smb' device (/dev/smb*), 1574# which is a child of the 'smbus' device. 1575# 1576# Supported devices: 1577# smb standard io through /dev/smb* 1578# 1579# ACPI support: 1580# smbacpi support for ACPI I2cSerialBus resources 1581# 1582# Supported SMB interfaces: 1583# iicsmb I2C to SMB bridge with any iicbus interface 1584# bktr brooktree848 I2C hardware interface 1585# intpm Intel PIIX4 (82371AB, 82443MX) Power Management Unit 1586# alpm Acer Aladdin-IV/V/Pro2 Power Management Unit 1587# ichiic Intel generation 4 I2C controller 1588# ichsmb Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA) 1589# viapm VIA VT82C586B,596,686A and VT8233 SMBus controllers 1590# amdpm AMD 756 Power Management Unit 1591# amdsmb AMD 8111 SMBus 2.0 Controller 1592# 1593device smbus # Bus support, required for smb below. 1594 1595device intpm 1596device alpm 1597device ichiic 1598device ichsmb 1599device viapm 1600device amdpm 1601device amdsmb 1602 1603device smb 1604 1605device smbacpi 1606 1607# 1608# I2C Bus 1609# 1610# Philips i2c bus support is provided by the `iicbus' device. 1611# 1612# Supported devices: 1613# ic i2c network interface 1614# iic i2c standard io 1615# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands. 1616# 1617# Supported interfaces: 1618# pcf Philips PCF8584 ISA-bus controller 1619# bktr brooktree848 I2C software interface 1620# 1621# Other: 1622# iicbb generic I2C bit-banging code (needed by lpbb, bktr) 1623# 1624device iicbus # Bus support, required for ic/iic/iicsmb below. 1625device iicbb 1626 1627device ic 1628device iic 1629device iicsmb # smb over i2c bridge 1630 1631device pcf0 at isa? port 0x320 irq 5 1632 1633# Intel performance-energy bias 1634device perfbias 1635 1636# Intel software controlled clock modulation 1637device clockmod 1638 1639# Intel Sandy Bridge and newer CPUs power usage estimation 1640device corepower 1641 1642# amdtemp: On-die sensor on AMD K8/K10/K11 CPUs 1643# coretemp: Intel Core and newer CPUs on-die digital thermal sensor support 1644device amdtemp 1645device coretemp 1646 1647# Memory thermal sensor 1648device memtemp 1649 1650# CPU control pseudo-device. Provides access to MSRs, CPUID info and 1651# microcode update feature. 1652device cpuctl 1653 1654# 1655# AMD System Management Network (SMN) 1656# 1657device amdsmn 1658 1659# Effective CPU frequency interface via APERF/MPERF MSRs 1660device aperf 1661 1662# AMD Family 0Fh, 10h and 11h temperature sensors 1663device kate 1664device km 1665 1666# ThinkPad Active Protection System accelerometer 1667device aps0 at isa? port 0x1600 1668 1669# HW monitoring devices lm(4), it(4) and nsclpcsio. 1670device lm0 at isa? port 0x290 1671device it0 at isa? port 0x290 1672device it1 at isa? port 0xc00 1673device it2 at isa? port 0xd00 1674device it3 at isa? port 0x228 1675device nsclpcsio0 at isa? port 0x2e 1676device nsclpcsio1 at isa? port 0x4e 1677device wbsio0 at isa? port 0x2e 1678device wbsio1 at isa? port 0x4e 1679device uguru0 at isa? port 0xe0 # ABIT uGuru 1680 1681# EFI Runtime Services support (not functional yet). 1682options EFIRT 1683 1684# Parallel-Port Bus 1685# 1686# Parallel port bus support is provided by the `ppbus' device. 1687# Multiple devices may be attached to the parallel port, devices 1688# are automatically probed and attached when found. 1689# 1690# Supported devices: 1691# vpo Iomega Zip Drive 1692# Requires SCSI disk support ('scbus' and 'da'); the best 1693# performance is achieved with ports in EPP 1.9 mode. 1694# lpt Parallel Printer 1695# plip Parallel network interface 1696# ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O 1697# pps Pulse per second Timing Interface 1698# lpbb Philips official parallel port I2C bit-banging interface 1699# 1700# Supported interfaces: 1701# ppc ISA-bus parallel port interfaces. 1702# 1703 1704options PPC_PROBE_CHIPSET # Enable chipset specific detection 1705 # (see flags in ppc(4)) 1706options DEBUG_1284 # IEEE1284 signaling protocol debug 1707options PERIPH_1284 # Makes your computer act as an IEEE1284 1708 # compliant peripheral 1709options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices 1710options VP0_DEBUG # ZIP/ZIP+ debug 1711options LPT_DEBUG # Printer driver debug 1712options PPC_DEBUG=2 # Parallel chipset level debug 1713options PLIP_DEBUG # Parallel network IP interface debug 1714options PCFCLOCK_VERBOSE # Verbose pcfclock driver 1715options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10) 1716 1717device ppc0 at isa? irq 7 1718device ppbus 1719device vpo 1720device lpt 1721device plip 1722device ppi 1723device pps 1724device lpbb 1725device pcfclock 1726 1727# Kernel BOOTP support 1728 1729options BOOTP # Use BOOTP to obtain IP address/hostname 1730options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info 1731options BOOTP_COMPAT # Workaround for broken bootp daemons. 1732options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP 1733 1734# Disable swapping. This option removes all code which actually performs 1735# swapping, so it's not possible to turn it back on at run-time. 1736# 1737# This is sometimes usable for systems which don't have any swap space 1738# (see also sysctls "vm.defer_swapspace_pageouts" and 1739# "vm.disable_swapspace_pageouts") 1740# 1741#options NO_SWAPPING 1742 1743# Set the size of the buffer cache KVM reservation, in buffers. This is 1744# scaled by approximately 16384 bytes. The system will auto-size the buffer 1745# cache if this option is not specified. 1746# 1747options NBUF=512 1748 1749# Set the size of the mbuf KVM reservation, in clusters. This is scaled 1750# by approximately 2048 bytes. The system will auto-size the mbuf area 1751# to (512 + maxusers*16) if this option is not specified. 1752# maxusers is in turn computed at boot time depending on available memory 1753# or set to the value specified by "options MAXUSERS=x" (x=0 means 1754# autoscaling). 1755# So, to take advantage of autoscaling, you have to remove both 1756# NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config. 1757# 1758options NMBCLUSTERS=1024 1759 1760# Set the number of mbufs available in the system. Each mbuf 1761# consumes 256 bytes. The system will autosize this (to 4 times 1762# the number of NMBCLUSTERS, depending on other constraints) 1763# if this option is not specified. 1764# 1765options NMBUFS=4096 1766 1767# Tune the buffer cache maximum KVA reservation, in bytes. The maximum is 1768# usually capped at 200 MB, effecting machines with > 1GB of ram. Note 1769# that the buffer cache only really governs write buffering and disk block 1770# translations. The VM page cache is our primary disk cache and is not 1771# effected by the size of the buffer cache. 1772# 1773options VM_BCACHE_SIZE_MAX="(100*1024*1024)" 1774 1775# Tune the swap zone KVA reservation, in bytes. The default is typically 1776# 70 MB, giving the system the ability to manage a maximum of 28GB worth 1777# of swapped out data. 1778# 1779options VM_SWZONE_SIZE_MAX="(50*1024*1024)" 1780 1781# 1782# Enable extra debugging code for locks. This stores the filename and 1783# line of whatever acquired the lock in the lock itself, and change a 1784# number of function calls to pass around the relevant data. This is 1785# not at all useful unless you are debugging lock code. Also note 1786# that it is likely to break e.g. fstat(1) unless you recompile your 1787# userland with -DDEBUG_LOCKS as well. 1788# 1789# DEBUG_LOCKS_LATENCY adds a sysctl to add a forced latency loop 1790# (count to N) in front of any spinlock or gettoken. 1791# 1792options DEBUG_LOCKS 1793options DEBUG_LOCKS_LATENCY 1794 1795# Set the amount of time (in seconds) the system will wait before 1796# rebooting automatically when a kernel panic occurs. If set to (-1), 1797# the system will wait indefinitely until a key is pressed on the 1798# console. 1799options PANIC_REBOOT_WAIT_TIME=16 1800 1801# Specify a lower limit for the number of swap I/O buffers. 1802# 1803#options NSWBUF_MIN=120 1804 1805# The 'asr' driver provides support for current DPT/Adaptec SCSI RAID 1806# controllers (SmartRAID V and VI and later). 1807# These controllers require the CAM infrastructure. 1808# 1809device asr 1810 1811# The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/). 1812# These have hardware RAID-{0,1,5} support, and do multi-initiator I/O. 1813# The DPT controllers are commonly re-licensed under other brand-names - 1814# some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and 1815# Compaq are actually DPT controllers. 1816# 1817# See src/sys/dev/raid/dpt for debugging and other subtle options. 1818# DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various 1819# instruments are enabled. The tools in 1820# /usr/sbin/dpt_* assume these to be enabled. 1821# DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT. 1822# If you ant the driver to handle timeouts, enable 1823# this option. If your system is very busy, this 1824# option will create more trouble than solve. 1825# DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to 1826# wait when timing out with the above option. 1827# DPT_DEBUG_xxxx These are controllable from sys/dev/raid/dpt/dpt.h 1828# DPT_LOST_IRQ When enabled, will try, once per second, to catch 1829# any interrupt that got lost. Seems to help in some 1830# DPT-firmware/Motherboard combinations. Minimal 1831# cost, great benefit. 1832# DPT_RESET_HBA Make "reset" actually reset the controller 1833# instead of fudging it. Only enable this if you 1834# are 100% certain you need it. 1835 1836device dpt 1837 1838# DPT options 1839#!CAM# options DPT_MEASURE_PERFORMANCE 1840#!CAM# options DPT_HANDLE_TIMEOUTS 1841options DPT_TIMEOUT_FACTOR=4 1842options DPT_LOST_IRQ 1843options DPT_RESET_HBA 1844 1845# 1846# Compaq "CISS" RAID controllers (SmartRAID 5* series) 1847# These controllers have a SCSI-like interface, and require the 1848# CAM infrastructure. 1849# 1850device ciss 1851 1852# 1853# Intel Integrated RAID controllers. 1854# This driver is supported and maintained by 1855# "Leubner, Achim" <Achim_Leubner@adaptec.com>. 1856# 1857device iir 1858 1859# 1860# Mylex AcceleRAID and eXtremeRAID controllers with v6 and later 1861# firmware. These controllers have a SCSI-like interface, and require 1862# the CAM infrastructure. 1863# 1864device mly 1865 1866# USB support 1867# 1868 1869# UHCI controller 1870device uhci 1871# OHCI controller 1872device ohci 1873# EHCI controller 1874device ehci 1875# XHCI controller 1876device xhci 1877# General USB code (mandatory for USB) 1878device usb 1879# Human Interface Device (anything with buttons and dials) 1880device uhid 1881# USB keyboard 1882device ukbd 1883# USB printer 1884device ulpt 1885# USB mass storage (Requires scbus and da) 1886device umass 1887# USB mass storage driver for device-side mode 1888device usfs 1889# USB modem support 1890device umodem 1891# USB mouse 1892device ums 1893# USB touchpad(s) 1894device wsp 1895# eGalax USB touch screen 1896device uep 1897# Diamond Rio 500 MP3 player 1898device urio 1899# USB com devices 1900device "u3g" 1901device uark 1902device ubsa 1903device ubser 1904device uchcom 1905device ucom 1906device ucycom 1907device ufoma 1908device uftdi 1909device ugensa 1910device uipaq 1911device umcs 1912device umct 1913device umoscom 1914device uplcom 1915device uslcom 1916device uvisor 1917device uvscom 1918 1919# 1920# USB ethernet support 1921device uether 1922# 1923# ADMtek USB ethernet. Supports the LinkSys USB100TX, 1924# the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX 1925# and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus 1926# eval board. 1927device aue 1928# 1929# ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the 1930# LinkSys USB200M and various other adapters. 1931device axe 1932# 1933# ASIX Electronics AX88178A/AX88179 USB 2.0/3.0 gigabit ethernet driver. 1934device axge 1935# 1936# Devices which communicate using Ethernet over USB, particularly 1937# Communication Device Class (CDC) Ethernet specification. Supports 1938# Sharp Zaurus PDAs, some DOCSIS cable modems and so on. 1939device cdce 1940# 1941# CATC USB-EL1201A USB ethernet. Supports the CATC Netmate 1942# and Netmate II, and the Belkin F5U111. 1943device cue 1944# 1945# USB Apple iPhone/iPad tethered Ethernet driver 1946device ipheth 1947# 1948# Kawasaki LSI ethernet. Supports the LinkSys USB10T, 1949# Entrega USB-NET-E45, Peracom Ethernet Adapter, the 1950# 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T, 1951# the Netgear EA101, the D-Link DSB-650, the SMC 2102USB 1952# and 2104USB, and the Corega USB-T. 1953device kue 1954# 1955# Moschip MCS7730/MCS7840 USB to fast ethernet. Supports the Sitecom LN030. 1956device mos 1957# 1958# Davicom DM9601E USB to fast ethernet. Supports the Corega FEther USB-TXC. 1959device udav 1960 1961# USB wireless NICs, requires wlan_amrr 1962# 1963# Ralink Technology RT2501USB/RT2601USB 1964device rum 1965# 1966# Ralink Technology RT2700U/RT2800U/RT3000U wireless driver 1967device run 1968device runfw 1969# 1970# RNDIS USB ethernet driver 1971device urndis 1972# 1973# Realtek RTL8188CU/RTL8192CU wireless driver 1974device urtwn 1975device urtwnfw 1976#options URTWN_WITHOUT_UCODE 1977 1978# Fm Radio 1979# 1980device ufm 1981 1982# Templates for programming USB device side drivers 1983# 1984device usb_template 1985 1986# debugging options for the USB subsystem 1987# 1988options USB_DEBUG 1989 1990# options for ukbd: 1991options UKBD_DFLT_KEYMAP # specify the built-in keymap 1992makeoptions UKBD_DFLT_KEYMAP=it.iso 1993 1994# Firewire support 1995device firewire # Firewire bus code 1996device sbp # SCSI over Firewire (Requires scbus and da) 1997device fwe # Ethernet over Firewire (non-standard!) 1998 1999# dcons support (Dumb Console Device) 2000device dcons # dumb console driver 2001device dcons_crom # FireWire attachment 2002options DCONS_BUF_SIZE=16384 # buffer size 2003options DCONS_POLL_HZ=100 # polling rate 2004options DCONS_FORCE_CONSOLE=1 # force to be the primary console 2005options DCONS_FORCE_GDB=1 # force to be the gdb device 2006 2007##################################################################### 2008# crypto subsystem 2009# 2010# This is a port of the openbsd crypto framework. Include this when 2011# you have a h/w crypto device to accelerate user applications that 2012# link to openssl. 2013# 2014# Drivers are ports from openbsd with some simple enhancements that have 2015# been fed back to openbsd (and hopefully will be included). 2016 2017device crypto # core crypto support 2018device cryptodev # /dev/crypto for access to h/w 2019 2020device rndtest # FIPS 140-2 entropy tester 2021 2022device hifn # Hifn 7951, 7781, etc. 2023options HIFN_DEBUG # enable debugging support: hw.hifn.debug 2024#options HIFN_NO_RNG # for devices without RNG 2025options HIFN_RNDTEST # enable rndtest support 2026 2027device safe # SafeNet 1141 2028options SAFE_DEBUG # enable debugging support: hw.safe.debug 2029#options SAFE_NO_RNG # for devices without RNG 2030options SAFE_RNDTEST # enable rndtest support 2031 2032device ubsec # Broadcom 5501, 5601, 58xx 2033options UBSEC_DEBUG # enable debugging support: hw.ubsec.debug 2034#options UBSEC_NO_RNG # for devices without RNG 2035options UBSEC_RNDTEST # enable rndtest support 2036 2037device aesni # hardware crypto/RNG for AES-NI 2038device padlock # hardware crypto/RNG for VIA C3/C7/Eden 2039device rdrand # hardware RNG for RdRand 2040 2041# 2042# ACPI support using the Intel ACPI Component Architecture reference 2043# implementation. 2044# 2045# ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer 2046# kernel environment variables to select initial debugging levels for the 2047# Intel ACPICA code. 2048 2049device acpi 2050options ACPI_DEBUG 2051 2052# ACPI WMI Mapping driver 2053device acpi_wmi 2054 2055# ACPI Asus Extras (LCD backlight/brightness, video output, etc.) 2056device acpi_asus 2057 2058# ACPI Fujitsu Extras (Buttons) 2059device acpi_fujitsu 2060 2061# ACPI extras driver for HP laptops 2062device acpi_hp 2063 2064# ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.) 2065device acpi_panasonic 2066 2067# ACPI pvpanic driver for virtual machines running in Qemu 2068device acpi_pvpanic 2069 2070# ACPI Sony extra (LCD brightness) 2071device acpi_sony 2072 2073# ACPI extras driver for ThinkPad laptops 2074device acpi_thinkpad 2075 2076# ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.) 2077device acpi_toshiba 2078 2079# ACPI Video Extensions (LCD backlight/brightness, video output, etc.) 2080device acpi_video 2081 2082# ACPI Docking Station 2083device acpi_dock 2084 2085device aibs # ASUSTeK AI Booster (ACPI ASOC ATK0110) 2086 2087# DRM options: 2088# drm: General DRM code 2089# i915: Intel integrated GPUs, starting from the 830M family 2090# radeon: ATI/AMD Radeon cards 2091# 2092# DRM_DEBUG: include debug printfs, very slow 2093# 2094# DRM requires AGP in the kernel. 2095# 2096# Also you'll need to have the following 3 lines in the kernel config. 2097# device acpi 2098# device iicbus 2099# device iicbb 2100 2101device drm 2102 2103# For testing and debugging. 2104device "i915" 2105device radeon 2106 2107options DRM_DEBUG 2108options VGA_SWITCHEROO 2109 2110# 2111# Misc devices 2112# 2113device cmx # Omnikey CardMan 4040 smartcard reader 2114device amdsbwd # AMD South Bridge watchdog 2115device gpio # Enable support for the gpio framework 2116device ichwd # Intel ICH watchdog interrupt timer 2117device tbridge # regression testing 2118 2119# 2120# Amazon EC2 support 2121# 2122device ena 2123 2124# 2125# Hyper-V support 2126# 2127device vmbus 2128 2129# 2130# Virtio support 2131# 2132device virtio # Generic VirtIO bus/PCI interface (required) 2133device virtio_balloon # VirtIO Memory Balloon device 2134device virtio_blk # VirtIO Block device 2135device virtio_random # VirtIO Entropy device 2136device virtio_scsi # VirtIO SCSI device 2137device vtnet # VirtIO Ethernet device 2138 2139# VMware support 2140# 2141device vmx # VMware VMXNET3 Ethernet 2142 2143# 2144# Gpio support for ACPI based SoC platforms 2145# 2146device gpio_acpi 2147device gpio_intel # GPIO support for Intel SoCs 2148 2149# 2150# Embedded system options: 2151# 2152# An embedded system might want to run something other than init. 2153options INIT_PATH="/sbin/init:/sbin/oinit" 2154 2155# Debug options 2156options BUS_DEBUG # enable newbus debugging 2157options RSS_DEBUG # enable RSS (Receive Side Scaling) debugging 2158 2159# Record the program counter of the code interrupted by the statistics 2160# clock interrupt. Use pctrack(8) to dump this information. 2161options DEBUG_PCTRACK 2162 2163# evdev interface 2164device evdev # input event device support 2165options EVDEV_SUPPORT # evdev support in legacy drivers 2166options EVDEV_DEBUG # enable event debug messages 2167 2168# More undocumented options for linting. 2169# Note that documenting these are not considered an affront. 2170 2171#options BKTR_ALLOC_PAGES=xxx 2172options CAM_DEBUG_DELAY 2173options CLUSTERDEBUG 2174options DEBUG 2175options DEBUG_CRIT_SECTIONS 2176options BCE_RSS_DEBUG 2177options BCE_TSS_DEBUG 2178options BNX_RSS_DEBUG 2179options BNX_TSO_DEBUG 2180options BNX_TSS_DEBUG 2181options EMX_RSS_DEBUG 2182options EMX_TSO_DEBUG 2183options EMX_TSS_DEBUG 2184options JME_RSS_DEBUG 2185options IGB_RSS_DEBUG 2186options IGB_TSS_DEBUG 2187options IGB_MSIX_DEBUG 2188options IX_RSS_DEBUG 2189options ENABLE_ALART 2190options FB_DEBUG=2 2191options FB_INSTALL_CDEV 2192#options IEEE80211_DEBUG_REFCNT 2193options IEEE80211_SUPPORT_SUPERG 2194options KBDIO_DEBUG=10 2195options KBD_MAXRETRY=4 2196options KBD_MAXWAIT=6 2197options KBD_RESETDELAY=201 2198#options KERN_TIMESTAMP 2199options KEY 2200options LOCKF_DEBUG 2201#options MAXFILES=xxx 2202options MBUF_DEBUG 2203options NO_LWKT_SPLIT_USERPRI 2204options PANIC_DEBUG 2205options PMAP_DEBUG 2206options PSM_DEBUG=4 2207options SCSI_NCR_DEBUG 2208options SCSI_NCR_MAX_SYNC=10000 2209options SCSI_NCR_MAX_WIDE=1 2210options SCSI_NCR_MYADDR=7 2211options SLAB_DEBUG 2212options SOCKBUF_DEBUG 2213options TDMA_BINTVAL_DEFAULT=5 2214options TDMA_SLOTCNT_DEFAULT=2 2215options TDMA_SLOTLEN_DEFAULT=10*1000 2216options TDMA_TXRATE_11A_DEFAULT=2*24 2217options TDMA_TXRATE_11B_DEFAULT=2*11 2218options TDMA_TXRATE_11G_DEFAULT=2*24 2219options TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)" 2220options TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)" 2221options TDMA_TXRATE_HALF_DEFAULT=2*12 2222options TDMA_TXRATE_QUARTER_DEFAULT=2*6 2223options TDMA_TXRATE_TURBO_DEFAULT=2*24 2224#options TIMER_FREQ="((14318182+6)/12)" 2225options VFS_BIO_DEBUG 2226options VM_PAGE_DEBUG 2227options XBONEHACK 2228 2229options KTR 2230options KTR_ALL 2231options KTR_ENTRIES=1024 2232options KTR_VERBOSE=1 2233#options KTR_ACPI_EC 2234#options KTR_CTXSW 2235#options KTR_DMCRYPT 2236#options KTR_ETHERNET 2237#options KTR_HAMMER 2238#options KTR_IFQ 2239#options KTR_IF_BGE 2240#options KTR_IF_EM 2241#options KTR_IF_EMX 2242#options KTR_IF_POLL 2243#options KTR_IF_START 2244#options KTR_IPIQ 2245#options KTR_KERNENTRY 2246#options KTR_LAPIC 2247#options KTR_MEMORY 2248#options KTR_SERIALIZER 2249#options KTR_SOWAKEUP 2250#options KTR_SPIN_CONTENTION 2251#options KTR_TESTLOG 2252#options KTR_TOKENS 2253#options KTR_TSLEEP 2254#options KTR_UDP 2255#options KTR_USCHED_BSD4 2256#options KTR_USCHED_DFLY 2257 2258# ALTQ 2259options ALTQ #alternate queueing 2260options ALTQ_CBQ #class based queueing 2261options ALTQ_RED #random early detection 2262options ALTQ_RIO #triple red for diffserv (needs RED) 2263options ALTQ_HFSC #hierarchical fair service curve 2264options ALTQ_PRIQ #priority queue 2265options ALTQ_FAIRQ #fair queue 2266#options ALTQ_NOPCC #don't use processor cycle counter 2267options ALTQ_DEBUG #for debugging 2268# you might want to set kernel timer to 1kHz if you use CBQ, 2269# especially with 100baseT 2270#options HZ=1000 2271 2272# WATCHDOG 2273options WDOG_DISABLE_ON_PANIC # Automatically disable watchdogs on panic 2274 2275# LED 2276device led 2277options ERROR_LED_ON_PANIC # If an error led is present, light it up on panic 2278