1 /****************************************************************************** 2 3 Copyright (c) 2001-2014, Intel Corporation 4 All rights reserved. 5 6 Redistribution and use in source and binary forms, with or without 7 modification, are permitted provided that the following conditions are met: 8 9 1. Redistributions of source code must retain the above copyright notice, 10 this list of conditions and the following disclaimer. 11 12 2. Redistributions in binary form must reproduce the above copyright 13 notice, this list of conditions and the following disclaimer in the 14 documentation and/or other materials provided with the distribution. 15 16 3. Neither the name of the Intel Corporation nor the names of its 17 contributors may be used to endorse or promote products derived from 18 this software without specific prior written permission. 19 20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 POSSIBILITY OF SUCH DAMAGE. 31 32 ******************************************************************************/ 33 /*$FreeBSD$*/ 34 35 #include "ixgbe_common.h" 36 #include "ixgbe_phy.h" 37 #include "ixgbe_dcb.h" 38 #include "ixgbe_dcb_82599.h" 39 #include "ixgbe_api.h" 40 41 static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw); 42 static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw); 43 static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw); 44 static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw); 45 static void ixgbe_standby_eeprom(struct ixgbe_hw *hw); 46 static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, 47 u16 count); 48 static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count); 49 static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); 50 static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); 51 static void ixgbe_release_eeprom(struct ixgbe_hw *hw); 52 53 static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr); 54 static s32 ixgbe_get_san_mac_addr_offset(struct ixgbe_hw *hw, 55 u16 *san_mac_offset); 56 static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, 57 u16 words, u16 *data); 58 static s32 ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, 59 u16 words, u16 *data); 60 static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw, 61 u16 offset); 62 63 /** 64 * ixgbe_init_ops_generic - Inits function ptrs 65 * @hw: pointer to the hardware structure 66 * 67 * Initialize the function pointers. 68 **/ 69 s32 ixgbe_init_ops_generic(struct ixgbe_hw *hw) 70 { 71 struct ixgbe_eeprom_info *eeprom = &hw->eeprom; 72 struct ixgbe_mac_info *mac = &hw->mac; 73 u32 eec = IXGBE_READ_REG(hw, IXGBE_EEC); 74 75 DEBUGFUNC("ixgbe_init_ops_generic"); 76 77 /* EEPROM */ 78 eeprom->ops.init_params = ixgbe_init_eeprom_params_generic; 79 /* If EEPROM is valid (bit 8 = 1), use EERD otherwise use bit bang */ 80 if (eec & IXGBE_EEC_PRES) { 81 eeprom->ops.read = ixgbe_read_eerd_generic; 82 eeprom->ops.read_buffer = ixgbe_read_eerd_buffer_generic; 83 } else { 84 eeprom->ops.read = ixgbe_read_eeprom_bit_bang_generic; 85 eeprom->ops.read_buffer = 86 ixgbe_read_eeprom_buffer_bit_bang_generic; 87 } 88 eeprom->ops.write = ixgbe_write_eeprom_generic; 89 eeprom->ops.write_buffer = ixgbe_write_eeprom_buffer_bit_bang_generic; 90 eeprom->ops.validate_checksum = 91 ixgbe_validate_eeprom_checksum_generic; 92 eeprom->ops.update_checksum = ixgbe_update_eeprom_checksum_generic; 93 eeprom->ops.calc_checksum = ixgbe_calc_eeprom_checksum_generic; 94 95 /* MAC */ 96 mac->ops.init_hw = ixgbe_init_hw_generic; 97 mac->ops.reset_hw = NULL; 98 mac->ops.start_hw = ixgbe_start_hw_generic; 99 mac->ops.clear_hw_cntrs = ixgbe_clear_hw_cntrs_generic; 100 mac->ops.get_media_type = NULL; 101 mac->ops.get_supported_physical_layer = NULL; 102 mac->ops.enable_rx_dma = ixgbe_enable_rx_dma_generic; 103 mac->ops.get_mac_addr = ixgbe_get_mac_addr_generic; 104 mac->ops.stop_adapter = ixgbe_stop_adapter_generic; 105 mac->ops.get_bus_info = ixgbe_get_bus_info_generic; 106 mac->ops.set_lan_id = ixgbe_set_lan_id_multi_port_pcie; 107 mac->ops.acquire_swfw_sync = ixgbe_acquire_swfw_sync; 108 mac->ops.release_swfw_sync = ixgbe_release_swfw_sync; 109 mac->ops.prot_autoc_read = prot_autoc_read_generic; 110 mac->ops.prot_autoc_write = prot_autoc_write_generic; 111 112 /* LEDs */ 113 mac->ops.led_on = ixgbe_led_on_generic; 114 mac->ops.led_off = ixgbe_led_off_generic; 115 mac->ops.blink_led_start = ixgbe_blink_led_start_generic; 116 mac->ops.blink_led_stop = ixgbe_blink_led_stop_generic; 117 118 /* RAR, Multicast, VLAN */ 119 mac->ops.set_rar = ixgbe_set_rar_generic; 120 mac->ops.clear_rar = ixgbe_clear_rar_generic; 121 mac->ops.insert_mac_addr = NULL; 122 mac->ops.set_vmdq = NULL; 123 mac->ops.clear_vmdq = NULL; 124 mac->ops.init_rx_addrs = ixgbe_init_rx_addrs_generic; 125 mac->ops.update_uc_addr_list = ixgbe_update_uc_addr_list_generic; 126 mac->ops.update_mc_addr_list = ixgbe_update_mc_addr_list_generic; 127 mac->ops.enable_mc = ixgbe_enable_mc_generic; 128 mac->ops.disable_mc = ixgbe_disable_mc_generic; 129 mac->ops.clear_vfta = NULL; 130 mac->ops.set_vfta = NULL; 131 mac->ops.set_vlvf = NULL; 132 mac->ops.init_uta_tables = NULL; 133 mac->ops.enable_rx = ixgbe_enable_rx_generic; 134 mac->ops.disable_rx = ixgbe_disable_rx_generic; 135 136 /* Flow Control */ 137 mac->ops.fc_enable = ixgbe_fc_enable_generic; 138 mac->ops.setup_fc = ixgbe_setup_fc_generic; 139 140 /* Link */ 141 mac->ops.get_link_capabilities = NULL; 142 mac->ops.setup_link = NULL; 143 mac->ops.check_link = NULL; 144 mac->ops.dmac_config = NULL; 145 mac->ops.dmac_update_tcs = NULL; 146 mac->ops.dmac_config_tcs = NULL; 147 148 return IXGBE_SUCCESS; 149 } 150 151 /** 152 * ixgbe_device_supports_autoneg_fc - Check if device supports autonegotiation 153 * of flow control 154 * @hw: pointer to hardware structure 155 * 156 * This function returns TRUE if the device supports flow control 157 * autonegotiation, and FALSE if it does not. 158 * 159 **/ 160 bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw) 161 { 162 bool supported = FALSE; 163 ixgbe_link_speed speed; 164 bool link_up; 165 166 DEBUGFUNC("ixgbe_device_supports_autoneg_fc"); 167 168 switch (hw->phy.media_type) { 169 case ixgbe_media_type_fiber_fixed: 170 case ixgbe_media_type_fiber_qsfp: 171 case ixgbe_media_type_fiber: 172 hw->mac.ops.check_link(hw, &speed, &link_up, FALSE); 173 /* if link is down, assume supported */ 174 if (link_up) 175 supported = speed == IXGBE_LINK_SPEED_1GB_FULL ? 176 TRUE : FALSE; 177 else 178 supported = TRUE; 179 break; 180 case ixgbe_media_type_backplane: 181 supported = TRUE; 182 break; 183 case ixgbe_media_type_copper: 184 /* only some copper devices support flow control autoneg */ 185 switch (hw->device_id) { 186 case IXGBE_DEV_ID_82599_T3_LOM: 187 case IXGBE_DEV_ID_X540T: 188 case IXGBE_DEV_ID_X540T1: 189 case IXGBE_DEV_ID_X540_BYPASS: 190 case IXGBE_DEV_ID_X550T: 191 case IXGBE_DEV_ID_X550EM_X_10G_T: 192 supported = TRUE; 193 break; 194 default: 195 supported = FALSE; 196 } 197 default: 198 break; 199 } 200 201 ERROR_REPORT2(IXGBE_ERROR_UNSUPPORTED, 202 "Device %x does not support flow control autoneg", 203 hw->device_id); 204 return supported; 205 } 206 207 /** 208 * ixgbe_setup_fc_generic - Set up flow control 209 * @hw: pointer to hardware structure 210 * 211 * Called at init time to set up flow control. 212 **/ 213 s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw) 214 { 215 s32 ret_val = IXGBE_SUCCESS; 216 u32 reg = 0, reg_bp = 0; 217 u16 reg_cu = 0; 218 bool locked = FALSE; 219 220 DEBUGFUNC("ixgbe_setup_fc_generic"); 221 222 /* Validate the requested mode */ 223 if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { 224 ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, 225 "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); 226 ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; 227 goto out; 228 } 229 230 /* 231 * 10gig parts do not have a word in the EEPROM to determine the 232 * default flow control setting, so we explicitly set it to full. 233 */ 234 if (hw->fc.requested_mode == ixgbe_fc_default) 235 hw->fc.requested_mode = ixgbe_fc_full; 236 237 /* 238 * Set up the 1G and 10G flow control advertisement registers so the 239 * HW will be able to do fc autoneg once the cable is plugged in. If 240 * we link at 10G, the 1G advertisement is harmless and vice versa. 241 */ 242 switch (hw->phy.media_type) { 243 case ixgbe_media_type_backplane: 244 /* some MAC's need RMW protection on AUTOC */ 245 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, ®_bp); 246 if (ret_val != IXGBE_SUCCESS) 247 goto out; 248 249 /* only backplane uses autoc so fall though */ 250 case ixgbe_media_type_fiber_fixed: 251 case ixgbe_media_type_fiber_qsfp: 252 case ixgbe_media_type_fiber: 253 reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); 254 255 break; 256 case ixgbe_media_type_copper: 257 hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_ADVT, 258 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®_cu); 259 break; 260 default: 261 break; 262 } 263 264 /* 265 * The possible values of fc.requested_mode are: 266 * 0: Flow control is completely disabled 267 * 1: Rx flow control is enabled (we can receive pause frames, 268 * but not send pause frames). 269 * 2: Tx flow control is enabled (we can send pause frames but 270 * we do not support receiving pause frames). 271 * 3: Both Rx and Tx flow control (symmetric) are enabled. 272 * other: Invalid. 273 */ 274 switch (hw->fc.requested_mode) { 275 case ixgbe_fc_none: 276 /* Flow control completely disabled by software override. */ 277 reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); 278 if (hw->phy.media_type == ixgbe_media_type_backplane) 279 reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE | 280 IXGBE_AUTOC_ASM_PAUSE); 281 else if (hw->phy.media_type == ixgbe_media_type_copper) 282 reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); 283 break; 284 case ixgbe_fc_tx_pause: 285 /* 286 * Tx Flow control is enabled, and Rx Flow control is 287 * disabled by software override. 288 */ 289 reg |= IXGBE_PCS1GANA_ASM_PAUSE; 290 reg &= ~IXGBE_PCS1GANA_SYM_PAUSE; 291 if (hw->phy.media_type == ixgbe_media_type_backplane) { 292 reg_bp |= IXGBE_AUTOC_ASM_PAUSE; 293 reg_bp &= ~IXGBE_AUTOC_SYM_PAUSE; 294 } else if (hw->phy.media_type == ixgbe_media_type_copper) { 295 reg_cu |= IXGBE_TAF_ASM_PAUSE; 296 reg_cu &= ~IXGBE_TAF_SYM_PAUSE; 297 } 298 break; 299 case ixgbe_fc_rx_pause: 300 /* 301 * Rx Flow control is enabled and Tx Flow control is 302 * disabled by software override. Since there really 303 * isn't a way to advertise that we are capable of RX 304 * Pause ONLY, we will advertise that we support both 305 * symmetric and asymmetric Rx PAUSE, as such we fall 306 * through to the fc_full statement. Later, we will 307 * disable the adapter's ability to send PAUSE frames. 308 */ 309 case ixgbe_fc_full: 310 /* Flow control (both Rx and Tx) is enabled by SW override. */ 311 reg |= IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE; 312 if (hw->phy.media_type == ixgbe_media_type_backplane) 313 reg_bp |= IXGBE_AUTOC_SYM_PAUSE | 314 IXGBE_AUTOC_ASM_PAUSE; 315 else if (hw->phy.media_type == ixgbe_media_type_copper) 316 reg_cu |= IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE; 317 break; 318 default: 319 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, 320 "Flow control param set incorrectly\n"); 321 ret_val = IXGBE_ERR_CONFIG; 322 goto out; 323 break; 324 } 325 326 if (hw->mac.type < ixgbe_mac_X540) { 327 /* 328 * Enable auto-negotiation between the MAC & PHY; 329 * the MAC will advertise clause 37 flow control. 330 */ 331 IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); 332 reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); 333 334 /* Disable AN timeout */ 335 if (hw->fc.strict_ieee) 336 reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; 337 338 IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); 339 DEBUGOUT1("Set up FC; PCS1GLCTL = 0x%08X\n", reg); 340 } 341 342 /* 343 * AUTOC restart handles negotiation of 1G and 10G on backplane 344 * and copper. There is no need to set the PCS1GCTL register. 345 * 346 */ 347 if (hw->phy.media_type == ixgbe_media_type_backplane) { 348 reg_bp |= IXGBE_AUTOC_AN_RESTART; 349 ret_val = hw->mac.ops.prot_autoc_write(hw, reg_bp, locked); 350 if (ret_val) 351 goto out; 352 } else if ((hw->phy.media_type == ixgbe_media_type_copper) && 353 (ixgbe_device_supports_autoneg_fc(hw))) { 354 hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_ADVT, 355 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, reg_cu); 356 } 357 358 DEBUGOUT1("Set up FC; PCS1GLCTL = 0x%08X\n", reg); 359 out: 360 return ret_val; 361 } 362 363 /** 364 * ixgbe_start_hw_generic - Prepare hardware for Tx/Rx 365 * @hw: pointer to hardware structure 366 * 367 * Starts the hardware by filling the bus info structure and media type, clears 368 * all on chip counters, initializes receive address registers, multicast 369 * table, VLAN filter table, calls routine to set up link and flow control 370 * settings, and leaves transmit and receive units disabled and uninitialized 371 **/ 372 s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw) 373 { 374 s32 ret_val; 375 u32 ctrl_ext; 376 377 DEBUGFUNC("ixgbe_start_hw_generic"); 378 379 /* Set the media type */ 380 hw->phy.media_type = hw->mac.ops.get_media_type(hw); 381 382 /* PHY ops initialization must be done in reset_hw() */ 383 384 /* Clear the VLAN filter table */ 385 hw->mac.ops.clear_vfta(hw); 386 387 /* Clear statistics registers */ 388 hw->mac.ops.clear_hw_cntrs(hw); 389 390 /* Set No Snoop Disable */ 391 ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT); 392 ctrl_ext |= IXGBE_CTRL_EXT_NS_DIS; 393 IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext); 394 IXGBE_WRITE_FLUSH(hw); 395 396 /* Setup flow control */ 397 ret_val = ixgbe_setup_fc(hw); 398 if (ret_val != IXGBE_SUCCESS) 399 goto out; 400 401 /* Clear adapter stopped flag */ 402 hw->adapter_stopped = FALSE; 403 404 out: 405 return ret_val; 406 } 407 408 /** 409 * ixgbe_start_hw_gen2 - Init sequence for common device family 410 * @hw: pointer to hw structure 411 * 412 * Performs the init sequence common to the second generation 413 * of 10 GbE devices. 414 * Devices in the second generation: 415 * 82599 416 * X540 417 **/ 418 s32 ixgbe_start_hw_gen2(struct ixgbe_hw *hw) 419 { 420 u32 i; 421 u32 regval; 422 423 /* Clear the rate limiters */ 424 for (i = 0; i < hw->mac.max_tx_queues; i++) { 425 IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, i); 426 IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, 0); 427 } 428 IXGBE_WRITE_FLUSH(hw); 429 430 /* Disable relaxed ordering */ 431 for (i = 0; i < hw->mac.max_tx_queues; i++) { 432 regval = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL_82599(i)); 433 regval &= ~IXGBE_DCA_TXCTRL_DESC_WRO_EN; 434 IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL_82599(i), regval); 435 } 436 437 for (i = 0; i < hw->mac.max_rx_queues; i++) { 438 regval = IXGBE_READ_REG(hw, IXGBE_DCA_RXCTRL(i)); 439 regval &= ~(IXGBE_DCA_RXCTRL_DATA_WRO_EN | 440 IXGBE_DCA_RXCTRL_HEAD_WRO_EN); 441 IXGBE_WRITE_REG(hw, IXGBE_DCA_RXCTRL(i), regval); 442 } 443 444 return IXGBE_SUCCESS; 445 } 446 447 /** 448 * ixgbe_init_hw_generic - Generic hardware initialization 449 * @hw: pointer to hardware structure 450 * 451 * Initialize the hardware by resetting the hardware, filling the bus info 452 * structure and media type, clears all on chip counters, initializes receive 453 * address registers, multicast table, VLAN filter table, calls routine to set 454 * up link and flow control settings, and leaves transmit and receive units 455 * disabled and uninitialized 456 **/ 457 s32 ixgbe_init_hw_generic(struct ixgbe_hw *hw) 458 { 459 s32 status; 460 461 DEBUGFUNC("ixgbe_init_hw_generic"); 462 463 /* Reset the hardware */ 464 status = hw->mac.ops.reset_hw(hw); 465 466 if (status == IXGBE_SUCCESS) { 467 /* Start the HW */ 468 status = hw->mac.ops.start_hw(hw); 469 } 470 471 return status; 472 } 473 474 /** 475 * ixgbe_clear_hw_cntrs_generic - Generic clear hardware counters 476 * @hw: pointer to hardware structure 477 * 478 * Clears all hardware statistics counters by reading them from the hardware 479 * Statistics counters are clear on read. 480 **/ 481 s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw) 482 { 483 u16 i = 0; 484 485 DEBUGFUNC("ixgbe_clear_hw_cntrs_generic"); 486 487 IXGBE_READ_REG(hw, IXGBE_CRCERRS); 488 IXGBE_READ_REG(hw, IXGBE_ILLERRC); 489 IXGBE_READ_REG(hw, IXGBE_ERRBC); 490 IXGBE_READ_REG(hw, IXGBE_MSPDC); 491 for (i = 0; i < 8; i++) 492 IXGBE_READ_REG(hw, IXGBE_MPC(i)); 493 494 IXGBE_READ_REG(hw, IXGBE_MLFC); 495 IXGBE_READ_REG(hw, IXGBE_MRFC); 496 IXGBE_READ_REG(hw, IXGBE_RLEC); 497 IXGBE_READ_REG(hw, IXGBE_LXONTXC); 498 IXGBE_READ_REG(hw, IXGBE_LXOFFTXC); 499 if (hw->mac.type >= ixgbe_mac_82599EB) { 500 IXGBE_READ_REG(hw, IXGBE_LXONRXCNT); 501 IXGBE_READ_REG(hw, IXGBE_LXOFFRXCNT); 502 } else { 503 IXGBE_READ_REG(hw, IXGBE_LXONRXC); 504 IXGBE_READ_REG(hw, IXGBE_LXOFFRXC); 505 } 506 507 for (i = 0; i < 8; i++) { 508 IXGBE_READ_REG(hw, IXGBE_PXONTXC(i)); 509 IXGBE_READ_REG(hw, IXGBE_PXOFFTXC(i)); 510 if (hw->mac.type >= ixgbe_mac_82599EB) { 511 IXGBE_READ_REG(hw, IXGBE_PXONRXCNT(i)); 512 IXGBE_READ_REG(hw, IXGBE_PXOFFRXCNT(i)); 513 } else { 514 IXGBE_READ_REG(hw, IXGBE_PXONRXC(i)); 515 IXGBE_READ_REG(hw, IXGBE_PXOFFRXC(i)); 516 } 517 } 518 if (hw->mac.type >= ixgbe_mac_82599EB) 519 for (i = 0; i < 8; i++) 520 IXGBE_READ_REG(hw, IXGBE_PXON2OFFCNT(i)); 521 IXGBE_READ_REG(hw, IXGBE_PRC64); 522 IXGBE_READ_REG(hw, IXGBE_PRC127); 523 IXGBE_READ_REG(hw, IXGBE_PRC255); 524 IXGBE_READ_REG(hw, IXGBE_PRC511); 525 IXGBE_READ_REG(hw, IXGBE_PRC1023); 526 IXGBE_READ_REG(hw, IXGBE_PRC1522); 527 IXGBE_READ_REG(hw, IXGBE_GPRC); 528 IXGBE_READ_REG(hw, IXGBE_BPRC); 529 IXGBE_READ_REG(hw, IXGBE_MPRC); 530 IXGBE_READ_REG(hw, IXGBE_GPTC); 531 IXGBE_READ_REG(hw, IXGBE_GORCL); 532 IXGBE_READ_REG(hw, IXGBE_GORCH); 533 IXGBE_READ_REG(hw, IXGBE_GOTCL); 534 IXGBE_READ_REG(hw, IXGBE_GOTCH); 535 if (hw->mac.type == ixgbe_mac_82598EB) 536 for (i = 0; i < 8; i++) 537 IXGBE_READ_REG(hw, IXGBE_RNBC(i)); 538 IXGBE_READ_REG(hw, IXGBE_RUC); 539 IXGBE_READ_REG(hw, IXGBE_RFC); 540 IXGBE_READ_REG(hw, IXGBE_ROC); 541 IXGBE_READ_REG(hw, IXGBE_RJC); 542 IXGBE_READ_REG(hw, IXGBE_MNGPRC); 543 IXGBE_READ_REG(hw, IXGBE_MNGPDC); 544 IXGBE_READ_REG(hw, IXGBE_MNGPTC); 545 IXGBE_READ_REG(hw, IXGBE_TORL); 546 IXGBE_READ_REG(hw, IXGBE_TORH); 547 IXGBE_READ_REG(hw, IXGBE_TPR); 548 IXGBE_READ_REG(hw, IXGBE_TPT); 549 IXGBE_READ_REG(hw, IXGBE_PTC64); 550 IXGBE_READ_REG(hw, IXGBE_PTC127); 551 IXGBE_READ_REG(hw, IXGBE_PTC255); 552 IXGBE_READ_REG(hw, IXGBE_PTC511); 553 IXGBE_READ_REG(hw, IXGBE_PTC1023); 554 IXGBE_READ_REG(hw, IXGBE_PTC1522); 555 IXGBE_READ_REG(hw, IXGBE_MPTC); 556 IXGBE_READ_REG(hw, IXGBE_BPTC); 557 for (i = 0; i < 16; i++) { 558 IXGBE_READ_REG(hw, IXGBE_QPRC(i)); 559 IXGBE_READ_REG(hw, IXGBE_QPTC(i)); 560 if (hw->mac.type >= ixgbe_mac_82599EB) { 561 IXGBE_READ_REG(hw, IXGBE_QBRC_L(i)); 562 IXGBE_READ_REG(hw, IXGBE_QBRC_H(i)); 563 IXGBE_READ_REG(hw, IXGBE_QBTC_L(i)); 564 IXGBE_READ_REG(hw, IXGBE_QBTC_H(i)); 565 IXGBE_READ_REG(hw, IXGBE_QPRDC(i)); 566 } else { 567 IXGBE_READ_REG(hw, IXGBE_QBRC(i)); 568 IXGBE_READ_REG(hw, IXGBE_QBTC(i)); 569 } 570 } 571 572 if (hw->mac.type == ixgbe_mac_X550 || hw->mac.type == ixgbe_mac_X540) { 573 if (hw->phy.id == 0) 574 ixgbe_identify_phy(hw); 575 hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECL, 576 IXGBE_MDIO_PCS_DEV_TYPE, &i); 577 hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECH, 578 IXGBE_MDIO_PCS_DEV_TYPE, &i); 579 hw->phy.ops.read_reg(hw, IXGBE_LDPCECL, 580 IXGBE_MDIO_PCS_DEV_TYPE, &i); 581 hw->phy.ops.read_reg(hw, IXGBE_LDPCECH, 582 IXGBE_MDIO_PCS_DEV_TYPE, &i); 583 } 584 585 return IXGBE_SUCCESS; 586 } 587 588 /** 589 * ixgbe_read_pba_string_generic - Reads part number string from EEPROM 590 * @hw: pointer to hardware structure 591 * @pba_num: stores the part number string from the EEPROM 592 * @pba_num_size: part number string buffer length 593 * 594 * Reads the part number string from the EEPROM. 595 **/ 596 s32 ixgbe_read_pba_string_generic(struct ixgbe_hw *hw, u8 *pba_num, 597 u32 pba_num_size) 598 { 599 s32 ret_val; 600 u16 data; 601 u16 pba_ptr; 602 u16 offset; 603 u16 length; 604 605 DEBUGFUNC("ixgbe_read_pba_string_generic"); 606 607 if (pba_num == NULL) { 608 DEBUGOUT("PBA string buffer was null\n"); 609 return IXGBE_ERR_INVALID_ARGUMENT; 610 } 611 612 ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data); 613 if (ret_val) { 614 DEBUGOUT("NVM Read Error\n"); 615 return ret_val; 616 } 617 618 ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &pba_ptr); 619 if (ret_val) { 620 DEBUGOUT("NVM Read Error\n"); 621 return ret_val; 622 } 623 624 /* 625 * if data is not ptr guard the PBA must be in legacy format which 626 * means pba_ptr is actually our second data word for the PBA number 627 * and we can decode it into an ascii string 628 */ 629 if (data != IXGBE_PBANUM_PTR_GUARD) { 630 DEBUGOUT("NVM PBA number is not stored as string\n"); 631 632 /* we will need 11 characters to store the PBA */ 633 if (pba_num_size < 11) { 634 DEBUGOUT("PBA string buffer too small\n"); 635 return IXGBE_ERR_NO_SPACE; 636 } 637 638 /* extract hex string from data and pba_ptr */ 639 pba_num[0] = (data >> 12) & 0xF; 640 pba_num[1] = (data >> 8) & 0xF; 641 pba_num[2] = (data >> 4) & 0xF; 642 pba_num[3] = data & 0xF; 643 pba_num[4] = (pba_ptr >> 12) & 0xF; 644 pba_num[5] = (pba_ptr >> 8) & 0xF; 645 pba_num[6] = '-'; 646 pba_num[7] = 0; 647 pba_num[8] = (pba_ptr >> 4) & 0xF; 648 pba_num[9] = pba_ptr & 0xF; 649 650 /* put a null character on the end of our string */ 651 pba_num[10] = '\0'; 652 653 /* switch all the data but the '-' to hex char */ 654 for (offset = 0; offset < 10; offset++) { 655 if (pba_num[offset] < 0xA) 656 pba_num[offset] += '0'; 657 else if (pba_num[offset] < 0x10) 658 pba_num[offset] += 'A' - 0xA; 659 } 660 661 return IXGBE_SUCCESS; 662 } 663 664 ret_val = hw->eeprom.ops.read(hw, pba_ptr, &length); 665 if (ret_val) { 666 DEBUGOUT("NVM Read Error\n"); 667 return ret_val; 668 } 669 670 if (length == 0xFFFF || length == 0) { 671 DEBUGOUT("NVM PBA number section invalid length\n"); 672 return IXGBE_ERR_PBA_SECTION; 673 } 674 675 /* check if pba_num buffer is big enough */ 676 if (pba_num_size < (((u32)length * 2) - 1)) { 677 DEBUGOUT("PBA string buffer too small\n"); 678 return IXGBE_ERR_NO_SPACE; 679 } 680 681 /* trim pba length from start of string */ 682 pba_ptr++; 683 length--; 684 685 for (offset = 0; offset < length; offset++) { 686 ret_val = hw->eeprom.ops.read(hw, pba_ptr + offset, &data); 687 if (ret_val) { 688 DEBUGOUT("NVM Read Error\n"); 689 return ret_val; 690 } 691 pba_num[offset * 2] = (u8)(data >> 8); 692 pba_num[(offset * 2) + 1] = (u8)(data & 0xFF); 693 } 694 pba_num[offset * 2] = '\0'; 695 696 return IXGBE_SUCCESS; 697 } 698 699 /** 700 * ixgbe_read_pba_num_generic - Reads part number from EEPROM 701 * @hw: pointer to hardware structure 702 * @pba_num: stores the part number from the EEPROM 703 * 704 * Reads the part number from the EEPROM. 705 **/ 706 s32 ixgbe_read_pba_num_generic(struct ixgbe_hw *hw, u32 *pba_num) 707 { 708 s32 ret_val; 709 u16 data; 710 711 DEBUGFUNC("ixgbe_read_pba_num_generic"); 712 713 ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data); 714 if (ret_val) { 715 DEBUGOUT("NVM Read Error\n"); 716 return ret_val; 717 } else if (data == IXGBE_PBANUM_PTR_GUARD) { 718 DEBUGOUT("NVM Not supported\n"); 719 return IXGBE_NOT_IMPLEMENTED; 720 } 721 *pba_num = (u32)(data << 16); 722 723 ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &data); 724 if (ret_val) { 725 DEBUGOUT("NVM Read Error\n"); 726 return ret_val; 727 } 728 *pba_num |= data; 729 730 return IXGBE_SUCCESS; 731 } 732 733 /** 734 * ixgbe_read_pba_raw 735 * @hw: pointer to the HW structure 736 * @eeprom_buf: optional pointer to EEPROM image 737 * @eeprom_buf_size: size of EEPROM image in words 738 * @max_pba_block_size: PBA block size limit 739 * @pba: pointer to output PBA structure 740 * 741 * Reads PBA from EEPROM image when eeprom_buf is not NULL. 742 * Reads PBA from physical EEPROM device when eeprom_buf is NULL. 743 * 744 **/ 745 s32 ixgbe_read_pba_raw(struct ixgbe_hw *hw, u16 *eeprom_buf, 746 u32 eeprom_buf_size, u16 max_pba_block_size, 747 struct ixgbe_pba *pba) 748 { 749 s32 ret_val; 750 u16 pba_block_size; 751 752 if (pba == NULL) 753 return IXGBE_ERR_PARAM; 754 755 if (eeprom_buf == NULL) { 756 ret_val = hw->eeprom.ops.read_buffer(hw, IXGBE_PBANUM0_PTR, 2, 757 &pba->word[0]); 758 if (ret_val) 759 return ret_val; 760 } else { 761 if (eeprom_buf_size > IXGBE_PBANUM1_PTR) { 762 pba->word[0] = eeprom_buf[IXGBE_PBANUM0_PTR]; 763 pba->word[1] = eeprom_buf[IXGBE_PBANUM1_PTR]; 764 } else { 765 return IXGBE_ERR_PARAM; 766 } 767 } 768 769 if (pba->word[0] == IXGBE_PBANUM_PTR_GUARD) { 770 if (pba->pba_block == NULL) 771 return IXGBE_ERR_PARAM; 772 773 ret_val = ixgbe_get_pba_block_size(hw, eeprom_buf, 774 eeprom_buf_size, 775 &pba_block_size); 776 if (ret_val) 777 return ret_val; 778 779 if (pba_block_size > max_pba_block_size) 780 return IXGBE_ERR_PARAM; 781 782 if (eeprom_buf == NULL) { 783 ret_val = hw->eeprom.ops.read_buffer(hw, pba->word[1], 784 pba_block_size, 785 pba->pba_block); 786 if (ret_val) 787 return ret_val; 788 } else { 789 if (eeprom_buf_size > (u32)(pba->word[1] + 790 pba_block_size)) { 791 memcpy(pba->pba_block, 792 &eeprom_buf[pba->word[1]], 793 pba_block_size * sizeof(u16)); 794 } else { 795 return IXGBE_ERR_PARAM; 796 } 797 } 798 } 799 800 return IXGBE_SUCCESS; 801 } 802 803 /** 804 * ixgbe_write_pba_raw 805 * @hw: pointer to the HW structure 806 * @eeprom_buf: optional pointer to EEPROM image 807 * @eeprom_buf_size: size of EEPROM image in words 808 * @pba: pointer to PBA structure 809 * 810 * Writes PBA to EEPROM image when eeprom_buf is not NULL. 811 * Writes PBA to physical EEPROM device when eeprom_buf is NULL. 812 * 813 **/ 814 s32 ixgbe_write_pba_raw(struct ixgbe_hw *hw, u16 *eeprom_buf, 815 u32 eeprom_buf_size, struct ixgbe_pba *pba) 816 { 817 s32 ret_val; 818 819 if (pba == NULL) 820 return IXGBE_ERR_PARAM; 821 822 if (eeprom_buf == NULL) { 823 ret_val = hw->eeprom.ops.write_buffer(hw, IXGBE_PBANUM0_PTR, 2, 824 &pba->word[0]); 825 if (ret_val) 826 return ret_val; 827 } else { 828 if (eeprom_buf_size > IXGBE_PBANUM1_PTR) { 829 eeprom_buf[IXGBE_PBANUM0_PTR] = pba->word[0]; 830 eeprom_buf[IXGBE_PBANUM1_PTR] = pba->word[1]; 831 } else { 832 return IXGBE_ERR_PARAM; 833 } 834 } 835 836 if (pba->word[0] == IXGBE_PBANUM_PTR_GUARD) { 837 if (pba->pba_block == NULL) 838 return IXGBE_ERR_PARAM; 839 840 if (eeprom_buf == NULL) { 841 ret_val = hw->eeprom.ops.write_buffer(hw, pba->word[1], 842 pba->pba_block[0], 843 pba->pba_block); 844 if (ret_val) 845 return ret_val; 846 } else { 847 if (eeprom_buf_size > (u32)(pba->word[1] + 848 pba->pba_block[0])) { 849 memcpy(&eeprom_buf[pba->word[1]], 850 pba->pba_block, 851 pba->pba_block[0] * sizeof(u16)); 852 } else { 853 return IXGBE_ERR_PARAM; 854 } 855 } 856 } 857 858 return IXGBE_SUCCESS; 859 } 860 861 /** 862 * ixgbe_get_pba_block_size 863 * @hw: pointer to the HW structure 864 * @eeprom_buf: optional pointer to EEPROM image 865 * @eeprom_buf_size: size of EEPROM image in words 866 * @pba_data_size: pointer to output variable 867 * 868 * Returns the size of the PBA block in words. Function operates on EEPROM 869 * image if the eeprom_buf pointer is not NULL otherwise it accesses physical 870 * EEPROM device. 871 * 872 **/ 873 s32 ixgbe_get_pba_block_size(struct ixgbe_hw *hw, u16 *eeprom_buf, 874 u32 eeprom_buf_size, u16 *pba_block_size) 875 { 876 s32 ret_val; 877 u16 pba_word[2]; 878 u16 length; 879 880 DEBUGFUNC("ixgbe_get_pba_block_size"); 881 882 if (eeprom_buf == NULL) { 883 ret_val = hw->eeprom.ops.read_buffer(hw, IXGBE_PBANUM0_PTR, 2, 884 &pba_word[0]); 885 if (ret_val) 886 return ret_val; 887 } else { 888 if (eeprom_buf_size > IXGBE_PBANUM1_PTR) { 889 pba_word[0] = eeprom_buf[IXGBE_PBANUM0_PTR]; 890 pba_word[1] = eeprom_buf[IXGBE_PBANUM1_PTR]; 891 } else { 892 return IXGBE_ERR_PARAM; 893 } 894 } 895 896 if (pba_word[0] == IXGBE_PBANUM_PTR_GUARD) { 897 if (eeprom_buf == NULL) { 898 ret_val = hw->eeprom.ops.read(hw, pba_word[1] + 0, 899 &length); 900 if (ret_val) 901 return ret_val; 902 } else { 903 if (eeprom_buf_size > pba_word[1]) 904 length = eeprom_buf[pba_word[1] + 0]; 905 else 906 return IXGBE_ERR_PARAM; 907 } 908 909 if (length == 0xFFFF || length == 0) 910 return IXGBE_ERR_PBA_SECTION; 911 } else { 912 /* PBA number in legacy format, there is no PBA Block. */ 913 length = 0; 914 } 915 916 if (pba_block_size != NULL) 917 *pba_block_size = length; 918 919 return IXGBE_SUCCESS; 920 } 921 922 /** 923 * ixgbe_get_mac_addr_generic - Generic get MAC address 924 * @hw: pointer to hardware structure 925 * @mac_addr: Adapter MAC address 926 * 927 * Reads the adapter's MAC address from first Receive Address Register (RAR0) 928 * A reset of the adapter must be performed prior to calling this function 929 * in order for the MAC address to have been loaded from the EEPROM into RAR0 930 **/ 931 s32 ixgbe_get_mac_addr_generic(struct ixgbe_hw *hw, u8 *mac_addr) 932 { 933 u32 rar_high; 934 u32 rar_low; 935 u16 i; 936 937 DEBUGFUNC("ixgbe_get_mac_addr_generic"); 938 939 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(0)); 940 rar_low = IXGBE_READ_REG(hw, IXGBE_RAL(0)); 941 942 for (i = 0; i < 4; i++) 943 mac_addr[i] = (u8)(rar_low >> (i*8)); 944 945 for (i = 0; i < 2; i++) 946 mac_addr[i+4] = (u8)(rar_high >> (i*8)); 947 948 return IXGBE_SUCCESS; 949 } 950 951 /** 952 * ixgbe_set_pci_config_data_generic - Generic store PCI bus info 953 * @hw: pointer to hardware structure 954 * @link_status: the link status returned by the PCI config space 955 * 956 * Stores the PCI bus info (speed, width, type) within the ixgbe_hw structure 957 **/ 958 void ixgbe_set_pci_config_data_generic(struct ixgbe_hw *hw, u16 link_status) 959 { 960 struct ixgbe_mac_info *mac = &hw->mac; 961 962 if (hw->bus.type == ixgbe_bus_type_unknown) 963 hw->bus.type = ixgbe_bus_type_pci_express; 964 965 switch (link_status & IXGBE_PCI_LINK_WIDTH) { 966 case IXGBE_PCI_LINK_WIDTH_1: 967 hw->bus.width = ixgbe_bus_width_pcie_x1; 968 break; 969 case IXGBE_PCI_LINK_WIDTH_2: 970 hw->bus.width = ixgbe_bus_width_pcie_x2; 971 break; 972 case IXGBE_PCI_LINK_WIDTH_4: 973 hw->bus.width = ixgbe_bus_width_pcie_x4; 974 break; 975 case IXGBE_PCI_LINK_WIDTH_8: 976 hw->bus.width = ixgbe_bus_width_pcie_x8; 977 break; 978 default: 979 hw->bus.width = ixgbe_bus_width_unknown; 980 break; 981 } 982 983 switch (link_status & IXGBE_PCI_LINK_SPEED) { 984 case IXGBE_PCI_LINK_SPEED_2500: 985 hw->bus.speed = ixgbe_bus_speed_2500; 986 break; 987 case IXGBE_PCI_LINK_SPEED_5000: 988 hw->bus.speed = ixgbe_bus_speed_5000; 989 break; 990 case IXGBE_PCI_LINK_SPEED_8000: 991 hw->bus.speed = ixgbe_bus_speed_8000; 992 break; 993 default: 994 hw->bus.speed = ixgbe_bus_speed_unknown; 995 break; 996 } 997 998 mac->ops.set_lan_id(hw); 999 } 1000 1001 /** 1002 * ixgbe_get_bus_info_generic - Generic set PCI bus info 1003 * @hw: pointer to hardware structure 1004 * 1005 * Gets the PCI bus info (speed, width, type) then calls helper function to 1006 * store this data within the ixgbe_hw structure. 1007 **/ 1008 s32 ixgbe_get_bus_info_generic(struct ixgbe_hw *hw) 1009 { 1010 u16 link_status; 1011 1012 DEBUGFUNC("ixgbe_get_bus_info_generic"); 1013 1014 /* Get the negotiated link width and speed from PCI config space */ 1015 link_status = IXGBE_READ_PCIE_WORD(hw, IXGBE_PCI_LINK_STATUS); 1016 1017 ixgbe_set_pci_config_data_generic(hw, link_status); 1018 1019 return IXGBE_SUCCESS; 1020 } 1021 1022 /** 1023 * ixgbe_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices 1024 * @hw: pointer to the HW structure 1025 * 1026 * Determines the LAN function id by reading memory-mapped registers 1027 * and swaps the port value if requested. 1028 **/ 1029 void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw) 1030 { 1031 struct ixgbe_bus_info *bus = &hw->bus; 1032 u32 reg; 1033 1034 DEBUGFUNC("ixgbe_set_lan_id_multi_port_pcie"); 1035 1036 reg = IXGBE_READ_REG(hw, IXGBE_STATUS); 1037 bus->func = (reg & IXGBE_STATUS_LAN_ID) >> IXGBE_STATUS_LAN_ID_SHIFT; 1038 bus->lan_id = bus->func; 1039 1040 /* check for a port swap */ 1041 reg = IXGBE_READ_REG(hw, IXGBE_FACTPS); 1042 if (reg & IXGBE_FACTPS_LFS) 1043 bus->func ^= 0x1; 1044 } 1045 1046 /** 1047 * ixgbe_stop_adapter_generic - Generic stop Tx/Rx units 1048 * @hw: pointer to hardware structure 1049 * 1050 * Sets the adapter_stopped flag within ixgbe_hw struct. Clears interrupts, 1051 * disables transmit and receive units. The adapter_stopped flag is used by 1052 * the shared code and drivers to determine if the adapter is in a stopped 1053 * state and should not touch the hardware. 1054 **/ 1055 s32 ixgbe_stop_adapter_generic(struct ixgbe_hw *hw) 1056 { 1057 u32 reg_val; 1058 u16 i; 1059 1060 DEBUGFUNC("ixgbe_stop_adapter_generic"); 1061 1062 /* 1063 * Set the adapter_stopped flag so other driver functions stop touching 1064 * the hardware 1065 */ 1066 hw->adapter_stopped = TRUE; 1067 1068 /* Disable the receive unit */ 1069 ixgbe_disable_rx(hw); 1070 1071 /* Clear interrupt mask to stop interrupts from being generated */ 1072 IXGBE_WRITE_REG(hw, IXGBE_EIMC, IXGBE_IRQ_CLEAR_MASK); 1073 1074 /* Clear any pending interrupts, flush previous writes */ 1075 IXGBE_READ_REG(hw, IXGBE_EICR); 1076 1077 /* Disable the transmit unit. Each queue must be disabled. */ 1078 for (i = 0; i < hw->mac.max_tx_queues; i++) 1079 IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(i), IXGBE_TXDCTL_SWFLSH); 1080 1081 /* Disable the receive unit by stopping each queue */ 1082 for (i = 0; i < hw->mac.max_rx_queues; i++) { 1083 reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i)); 1084 reg_val &= ~IXGBE_RXDCTL_ENABLE; 1085 reg_val |= IXGBE_RXDCTL_SWFLSH; 1086 IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val); 1087 } 1088 1089 /* flush all queues disables */ 1090 IXGBE_WRITE_FLUSH(hw); 1091 msec_delay(2); 1092 1093 /* 1094 * Prevent the PCI-E bus from hanging by disabling PCI-E master 1095 * access and verify no pending requests 1096 */ 1097 return ixgbe_disable_pcie_master(hw); 1098 } 1099 1100 /** 1101 * ixgbe_led_on_generic - Turns on the software controllable LEDs. 1102 * @hw: pointer to hardware structure 1103 * @index: led number to turn on 1104 **/ 1105 s32 ixgbe_led_on_generic(struct ixgbe_hw *hw, u32 index) 1106 { 1107 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); 1108 1109 DEBUGFUNC("ixgbe_led_on_generic"); 1110 1111 /* To turn on the LED, set mode to ON. */ 1112 led_reg &= ~IXGBE_LED_MODE_MASK(index); 1113 led_reg |= IXGBE_LED_ON << IXGBE_LED_MODE_SHIFT(index); 1114 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); 1115 IXGBE_WRITE_FLUSH(hw); 1116 1117 return IXGBE_SUCCESS; 1118 } 1119 1120 /** 1121 * ixgbe_led_off_generic - Turns off the software controllable LEDs. 1122 * @hw: pointer to hardware structure 1123 * @index: led number to turn off 1124 **/ 1125 s32 ixgbe_led_off_generic(struct ixgbe_hw *hw, u32 index) 1126 { 1127 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); 1128 1129 DEBUGFUNC("ixgbe_led_off_generic"); 1130 1131 /* To turn off the LED, set mode to OFF. */ 1132 led_reg &= ~IXGBE_LED_MODE_MASK(index); 1133 led_reg |= IXGBE_LED_OFF << IXGBE_LED_MODE_SHIFT(index); 1134 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); 1135 IXGBE_WRITE_FLUSH(hw); 1136 1137 return IXGBE_SUCCESS; 1138 } 1139 1140 /** 1141 * ixgbe_init_eeprom_params_generic - Initialize EEPROM params 1142 * @hw: pointer to hardware structure 1143 * 1144 * Initializes the EEPROM parameters ixgbe_eeprom_info within the 1145 * ixgbe_hw struct in order to set up EEPROM access. 1146 **/ 1147 s32 ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw) 1148 { 1149 struct ixgbe_eeprom_info *eeprom = &hw->eeprom; 1150 u32 eec; 1151 u16 eeprom_size; 1152 1153 DEBUGFUNC("ixgbe_init_eeprom_params_generic"); 1154 1155 if (eeprom->type == ixgbe_eeprom_uninitialized) { 1156 eeprom->type = ixgbe_eeprom_none; 1157 /* Set default semaphore delay to 10ms which is a well 1158 * tested value */ 1159 eeprom->semaphore_delay = 10; 1160 /* Clear EEPROM page size, it will be initialized as needed */ 1161 eeprom->word_page_size = 0; 1162 1163 /* 1164 * Check for EEPROM present first. 1165 * If not present leave as none 1166 */ 1167 eec = IXGBE_READ_REG(hw, IXGBE_EEC); 1168 if (eec & IXGBE_EEC_PRES) { 1169 eeprom->type = ixgbe_eeprom_spi; 1170 1171 /* 1172 * SPI EEPROM is assumed here. This code would need to 1173 * change if a future EEPROM is not SPI. 1174 */ 1175 eeprom_size = (u16)((eec & IXGBE_EEC_SIZE) >> 1176 IXGBE_EEC_SIZE_SHIFT); 1177 eeprom->word_size = 1 << (eeprom_size + 1178 IXGBE_EEPROM_WORD_SIZE_SHIFT); 1179 } 1180 1181 if (eec & IXGBE_EEC_ADDR_SIZE) 1182 eeprom->address_bits = 16; 1183 else 1184 eeprom->address_bits = 8; 1185 DEBUGOUT3("Eeprom params: type = %d, size = %d, address bits: " 1186 "%d\n", eeprom->type, eeprom->word_size, 1187 eeprom->address_bits); 1188 } 1189 1190 return IXGBE_SUCCESS; 1191 } 1192 1193 /** 1194 * ixgbe_write_eeprom_buffer_bit_bang_generic - Write EEPROM using bit-bang 1195 * @hw: pointer to hardware structure 1196 * @offset: offset within the EEPROM to write 1197 * @words: number of word(s) 1198 * @data: 16 bit word(s) to write to EEPROM 1199 * 1200 * Reads 16 bit word(s) from EEPROM through bit-bang method 1201 **/ 1202 s32 ixgbe_write_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, 1203 u16 words, u16 *data) 1204 { 1205 s32 status = IXGBE_SUCCESS; 1206 u16 i, count; 1207 1208 DEBUGFUNC("ixgbe_write_eeprom_buffer_bit_bang_generic"); 1209 1210 hw->eeprom.ops.init_params(hw); 1211 1212 if (words == 0) { 1213 status = IXGBE_ERR_INVALID_ARGUMENT; 1214 goto out; 1215 } 1216 1217 if (offset + words > hw->eeprom.word_size) { 1218 status = IXGBE_ERR_EEPROM; 1219 goto out; 1220 } 1221 1222 /* 1223 * The EEPROM page size cannot be queried from the chip. We do lazy 1224 * initialization. It is worth to do that when we write large buffer. 1225 */ 1226 if ((hw->eeprom.word_page_size == 0) && 1227 (words > IXGBE_EEPROM_PAGE_SIZE_MAX)) 1228 ixgbe_detect_eeprom_page_size_generic(hw, offset); 1229 1230 /* 1231 * We cannot hold synchronization semaphores for too long 1232 * to avoid other entity starvation. However it is more efficient 1233 * to read in bursts than synchronizing access for each word. 1234 */ 1235 for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) { 1236 count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ? 1237 IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i); 1238 status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset + i, 1239 count, &data[i]); 1240 1241 if (status != IXGBE_SUCCESS) 1242 break; 1243 } 1244 1245 out: 1246 return status; 1247 } 1248 1249 /** 1250 * ixgbe_write_eeprom_buffer_bit_bang - Writes 16 bit word(s) to EEPROM 1251 * @hw: pointer to hardware structure 1252 * @offset: offset within the EEPROM to be written to 1253 * @words: number of word(s) 1254 * @data: 16 bit word(s) to be written to the EEPROM 1255 * 1256 * If ixgbe_eeprom_update_checksum is not called after this function, the 1257 * EEPROM will most likely contain an invalid checksum. 1258 **/ 1259 static s32 ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, 1260 u16 words, u16 *data) 1261 { 1262 s32 status; 1263 u16 word; 1264 u16 page_size; 1265 u16 i; 1266 u8 write_opcode = IXGBE_EEPROM_WRITE_OPCODE_SPI; 1267 1268 DEBUGFUNC("ixgbe_write_eeprom_buffer_bit_bang"); 1269 1270 /* Prepare the EEPROM for writing */ 1271 status = ixgbe_acquire_eeprom(hw); 1272 1273 if (status == IXGBE_SUCCESS) { 1274 if (ixgbe_ready_eeprom(hw) != IXGBE_SUCCESS) { 1275 ixgbe_release_eeprom(hw); 1276 status = IXGBE_ERR_EEPROM; 1277 } 1278 } 1279 1280 if (status == IXGBE_SUCCESS) { 1281 for (i = 0; i < words; i++) { 1282 ixgbe_standby_eeprom(hw); 1283 1284 /* Send the WRITE ENABLE command (8 bit opcode ) */ 1285 ixgbe_shift_out_eeprom_bits(hw, 1286 IXGBE_EEPROM_WREN_OPCODE_SPI, 1287 IXGBE_EEPROM_OPCODE_BITS); 1288 1289 ixgbe_standby_eeprom(hw); 1290 1291 /* 1292 * Some SPI eeproms use the 8th address bit embedded 1293 * in the opcode 1294 */ 1295 if ((hw->eeprom.address_bits == 8) && 1296 ((offset + i) >= 128)) 1297 write_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI; 1298 1299 /* Send the Write command (8-bit opcode + addr) */ 1300 ixgbe_shift_out_eeprom_bits(hw, write_opcode, 1301 IXGBE_EEPROM_OPCODE_BITS); 1302 ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2), 1303 hw->eeprom.address_bits); 1304 1305 page_size = hw->eeprom.word_page_size; 1306 1307 /* Send the data in burst via SPI*/ 1308 do { 1309 word = data[i]; 1310 word = (word >> 8) | (word << 8); 1311 ixgbe_shift_out_eeprom_bits(hw, word, 16); 1312 1313 if (page_size == 0) 1314 break; 1315 1316 /* do not wrap around page */ 1317 if (((offset + i) & (page_size - 1)) == 1318 (page_size - 1)) 1319 break; 1320 } while (++i < words); 1321 1322 ixgbe_standby_eeprom(hw); 1323 msec_delay(10); 1324 } 1325 /* Done with writing - release the EEPROM */ 1326 ixgbe_release_eeprom(hw); 1327 } 1328 1329 return status; 1330 } 1331 1332 /** 1333 * ixgbe_write_eeprom_generic - Writes 16 bit value to EEPROM 1334 * @hw: pointer to hardware structure 1335 * @offset: offset within the EEPROM to be written to 1336 * @data: 16 bit word to be written to the EEPROM 1337 * 1338 * If ixgbe_eeprom_update_checksum is not called after this function, the 1339 * EEPROM will most likely contain an invalid checksum. 1340 **/ 1341 s32 ixgbe_write_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 data) 1342 { 1343 s32 status; 1344 1345 DEBUGFUNC("ixgbe_write_eeprom_generic"); 1346 1347 hw->eeprom.ops.init_params(hw); 1348 1349 if (offset >= hw->eeprom.word_size) { 1350 status = IXGBE_ERR_EEPROM; 1351 goto out; 1352 } 1353 1354 status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset, 1, &data); 1355 1356 out: 1357 return status; 1358 } 1359 1360 /** 1361 * ixgbe_read_eeprom_buffer_bit_bang_generic - Read EEPROM using bit-bang 1362 * @hw: pointer to hardware structure 1363 * @offset: offset within the EEPROM to be read 1364 * @data: read 16 bit words(s) from EEPROM 1365 * @words: number of word(s) 1366 * 1367 * Reads 16 bit word(s) from EEPROM through bit-bang method 1368 **/ 1369 s32 ixgbe_read_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, 1370 u16 words, u16 *data) 1371 { 1372 s32 status = IXGBE_SUCCESS; 1373 u16 i, count; 1374 1375 DEBUGFUNC("ixgbe_read_eeprom_buffer_bit_bang_generic"); 1376 1377 hw->eeprom.ops.init_params(hw); 1378 1379 if (words == 0) { 1380 status = IXGBE_ERR_INVALID_ARGUMENT; 1381 goto out; 1382 } 1383 1384 if (offset + words > hw->eeprom.word_size) { 1385 status = IXGBE_ERR_EEPROM; 1386 goto out; 1387 } 1388 1389 /* 1390 * We cannot hold synchronization semaphores for too long 1391 * to avoid other entity starvation. However it is more efficient 1392 * to read in bursts than synchronizing access for each word. 1393 */ 1394 for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) { 1395 count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ? 1396 IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i); 1397 1398 status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset + i, 1399 count, &data[i]); 1400 1401 if (status != IXGBE_SUCCESS) 1402 break; 1403 } 1404 1405 out: 1406 return status; 1407 } 1408 1409 /** 1410 * ixgbe_read_eeprom_buffer_bit_bang - Read EEPROM using bit-bang 1411 * @hw: pointer to hardware structure 1412 * @offset: offset within the EEPROM to be read 1413 * @words: number of word(s) 1414 * @data: read 16 bit word(s) from EEPROM 1415 * 1416 * Reads 16 bit word(s) from EEPROM through bit-bang method 1417 **/ 1418 static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset, 1419 u16 words, u16 *data) 1420 { 1421 s32 status; 1422 u16 word_in; 1423 u8 read_opcode = IXGBE_EEPROM_READ_OPCODE_SPI; 1424 u16 i; 1425 1426 DEBUGFUNC("ixgbe_read_eeprom_buffer_bit_bang"); 1427 1428 /* Prepare the EEPROM for reading */ 1429 status = ixgbe_acquire_eeprom(hw); 1430 1431 if (status == IXGBE_SUCCESS) { 1432 if (ixgbe_ready_eeprom(hw) != IXGBE_SUCCESS) { 1433 ixgbe_release_eeprom(hw); 1434 status = IXGBE_ERR_EEPROM; 1435 } 1436 } 1437 1438 if (status == IXGBE_SUCCESS) { 1439 for (i = 0; i < words; i++) { 1440 ixgbe_standby_eeprom(hw); 1441 /* 1442 * Some SPI eeproms use the 8th address bit embedded 1443 * in the opcode 1444 */ 1445 if ((hw->eeprom.address_bits == 8) && 1446 ((offset + i) >= 128)) 1447 read_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI; 1448 1449 /* Send the READ command (opcode + addr) */ 1450 ixgbe_shift_out_eeprom_bits(hw, read_opcode, 1451 IXGBE_EEPROM_OPCODE_BITS); 1452 ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2), 1453 hw->eeprom.address_bits); 1454 1455 /* Read the data. */ 1456 word_in = ixgbe_shift_in_eeprom_bits(hw, 16); 1457 data[i] = (word_in >> 8) | (word_in << 8); 1458 } 1459 1460 /* End this read operation */ 1461 ixgbe_release_eeprom(hw); 1462 } 1463 1464 return status; 1465 } 1466 1467 /** 1468 * ixgbe_read_eeprom_bit_bang_generic - Read EEPROM word using bit-bang 1469 * @hw: pointer to hardware structure 1470 * @offset: offset within the EEPROM to be read 1471 * @data: read 16 bit value from EEPROM 1472 * 1473 * Reads 16 bit value from EEPROM through bit-bang method 1474 **/ 1475 s32 ixgbe_read_eeprom_bit_bang_generic(struct ixgbe_hw *hw, u16 offset, 1476 u16 *data) 1477 { 1478 s32 status; 1479 1480 DEBUGFUNC("ixgbe_read_eeprom_bit_bang_generic"); 1481 1482 hw->eeprom.ops.init_params(hw); 1483 1484 if (offset >= hw->eeprom.word_size) { 1485 status = IXGBE_ERR_EEPROM; 1486 goto out; 1487 } 1488 1489 status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data); 1490 1491 out: 1492 return status; 1493 } 1494 1495 /** 1496 * ixgbe_read_eerd_buffer_generic - Read EEPROM word(s) using EERD 1497 * @hw: pointer to hardware structure 1498 * @offset: offset of word in the EEPROM to read 1499 * @words: number of word(s) 1500 * @data: 16 bit word(s) from the EEPROM 1501 * 1502 * Reads a 16 bit word(s) from the EEPROM using the EERD register. 1503 **/ 1504 s32 ixgbe_read_eerd_buffer_generic(struct ixgbe_hw *hw, u16 offset, 1505 u16 words, u16 *data) 1506 { 1507 u32 eerd; 1508 s32 status = IXGBE_SUCCESS; 1509 u32 i; 1510 1511 DEBUGFUNC("ixgbe_read_eerd_buffer_generic"); 1512 1513 hw->eeprom.ops.init_params(hw); 1514 1515 if (words == 0) { 1516 status = IXGBE_ERR_INVALID_ARGUMENT; 1517 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, "Invalid EEPROM words"); 1518 goto out; 1519 } 1520 1521 if (offset >= hw->eeprom.word_size) { 1522 status = IXGBE_ERR_EEPROM; 1523 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, "Invalid EEPROM offset"); 1524 goto out; 1525 } 1526 1527 for (i = 0; i < words; i++) { 1528 eerd = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) | 1529 IXGBE_EEPROM_RW_REG_START; 1530 1531 IXGBE_WRITE_REG(hw, IXGBE_EERD, eerd); 1532 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_READ); 1533 1534 if (status == IXGBE_SUCCESS) { 1535 data[i] = (IXGBE_READ_REG(hw, IXGBE_EERD) >> 1536 IXGBE_EEPROM_RW_REG_DATA); 1537 } else { 1538 DEBUGOUT("Eeprom read timed out\n"); 1539 goto out; 1540 } 1541 } 1542 out: 1543 return status; 1544 } 1545 1546 /** 1547 * ixgbe_detect_eeprom_page_size_generic - Detect EEPROM page size 1548 * @hw: pointer to hardware structure 1549 * @offset: offset within the EEPROM to be used as a scratch pad 1550 * 1551 * Discover EEPROM page size by writing marching data at given offset. 1552 * This function is called only when we are writing a new large buffer 1553 * at given offset so the data would be overwritten anyway. 1554 **/ 1555 static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw, 1556 u16 offset) 1557 { 1558 u16 data[IXGBE_EEPROM_PAGE_SIZE_MAX]; 1559 s32 status = IXGBE_SUCCESS; 1560 u16 i; 1561 1562 DEBUGFUNC("ixgbe_detect_eeprom_page_size_generic"); 1563 1564 for (i = 0; i < IXGBE_EEPROM_PAGE_SIZE_MAX; i++) 1565 data[i] = i; 1566 1567 hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX; 1568 status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset, 1569 IXGBE_EEPROM_PAGE_SIZE_MAX, data); 1570 hw->eeprom.word_page_size = 0; 1571 if (status != IXGBE_SUCCESS) 1572 goto out; 1573 1574 status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data); 1575 if (status != IXGBE_SUCCESS) 1576 goto out; 1577 1578 /* 1579 * When writing in burst more than the actual page size 1580 * EEPROM address wraps around current page. 1581 */ 1582 hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX - data[0]; 1583 1584 DEBUGOUT1("Detected EEPROM page size = %d words.", 1585 hw->eeprom.word_page_size); 1586 out: 1587 return status; 1588 } 1589 1590 /** 1591 * ixgbe_read_eerd_generic - Read EEPROM word using EERD 1592 * @hw: pointer to hardware structure 1593 * @offset: offset of word in the EEPROM to read 1594 * @data: word read from the EEPROM 1595 * 1596 * Reads a 16 bit word from the EEPROM using the EERD register. 1597 **/ 1598 s32 ixgbe_read_eerd_generic(struct ixgbe_hw *hw, u16 offset, u16 *data) 1599 { 1600 return ixgbe_read_eerd_buffer_generic(hw, offset, 1, data); 1601 } 1602 1603 /** 1604 * ixgbe_write_eewr_buffer_generic - Write EEPROM word(s) using EEWR 1605 * @hw: pointer to hardware structure 1606 * @offset: offset of word in the EEPROM to write 1607 * @words: number of word(s) 1608 * @data: word(s) write to the EEPROM 1609 * 1610 * Write a 16 bit word(s) to the EEPROM using the EEWR register. 1611 **/ 1612 s32 ixgbe_write_eewr_buffer_generic(struct ixgbe_hw *hw, u16 offset, 1613 u16 words, u16 *data) 1614 { 1615 u32 eewr; 1616 s32 status = IXGBE_SUCCESS; 1617 u16 i; 1618 1619 DEBUGFUNC("ixgbe_write_eewr_generic"); 1620 1621 hw->eeprom.ops.init_params(hw); 1622 1623 if (words == 0) { 1624 status = IXGBE_ERR_INVALID_ARGUMENT; 1625 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, "Invalid EEPROM words"); 1626 goto out; 1627 } 1628 1629 if (offset >= hw->eeprom.word_size) { 1630 status = IXGBE_ERR_EEPROM; 1631 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, "Invalid EEPROM offset"); 1632 goto out; 1633 } 1634 1635 for (i = 0; i < words; i++) { 1636 eewr = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) | 1637 (data[i] << IXGBE_EEPROM_RW_REG_DATA) | 1638 IXGBE_EEPROM_RW_REG_START; 1639 1640 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE); 1641 if (status != IXGBE_SUCCESS) { 1642 DEBUGOUT("Eeprom write EEWR timed out\n"); 1643 goto out; 1644 } 1645 1646 IXGBE_WRITE_REG(hw, IXGBE_EEWR, eewr); 1647 1648 status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE); 1649 if (status != IXGBE_SUCCESS) { 1650 DEBUGOUT("Eeprom write EEWR timed out\n"); 1651 goto out; 1652 } 1653 } 1654 1655 out: 1656 return status; 1657 } 1658 1659 /** 1660 * ixgbe_write_eewr_generic - Write EEPROM word using EEWR 1661 * @hw: pointer to hardware structure 1662 * @offset: offset of word in the EEPROM to write 1663 * @data: word write to the EEPROM 1664 * 1665 * Write a 16 bit word to the EEPROM using the EEWR register. 1666 **/ 1667 s32 ixgbe_write_eewr_generic(struct ixgbe_hw *hw, u16 offset, u16 data) 1668 { 1669 return ixgbe_write_eewr_buffer_generic(hw, offset, 1, &data); 1670 } 1671 1672 /** 1673 * ixgbe_poll_eerd_eewr_done - Poll EERD read or EEWR write status 1674 * @hw: pointer to hardware structure 1675 * @ee_reg: EEPROM flag for polling 1676 * 1677 * Polls the status bit (bit 1) of the EERD or EEWR to determine when the 1678 * read or write is done respectively. 1679 **/ 1680 s32 ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg) 1681 { 1682 u32 i; 1683 u32 reg; 1684 s32 status = IXGBE_ERR_EEPROM; 1685 1686 DEBUGFUNC("ixgbe_poll_eerd_eewr_done"); 1687 1688 for (i = 0; i < IXGBE_EERD_EEWR_ATTEMPTS; i++) { 1689 if (ee_reg == IXGBE_NVM_POLL_READ) 1690 reg = IXGBE_READ_REG(hw, IXGBE_EERD); 1691 else 1692 reg = IXGBE_READ_REG(hw, IXGBE_EEWR); 1693 1694 if (reg & IXGBE_EEPROM_RW_REG_DONE) { 1695 status = IXGBE_SUCCESS; 1696 break; 1697 } 1698 usec_delay(5); 1699 } 1700 1701 if (i == IXGBE_EERD_EEWR_ATTEMPTS) 1702 ERROR_REPORT1(IXGBE_ERROR_POLLING, 1703 "EEPROM read/write done polling timed out"); 1704 1705 return status; 1706 } 1707 1708 /** 1709 * ixgbe_acquire_eeprom - Acquire EEPROM using bit-bang 1710 * @hw: pointer to hardware structure 1711 * 1712 * Prepares EEPROM for access using bit-bang method. This function should 1713 * be called before issuing a command to the EEPROM. 1714 **/ 1715 static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw) 1716 { 1717 s32 status = IXGBE_SUCCESS; 1718 u32 eec; 1719 u32 i; 1720 1721 DEBUGFUNC("ixgbe_acquire_eeprom"); 1722 1723 if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) 1724 != IXGBE_SUCCESS) 1725 status = IXGBE_ERR_SWFW_SYNC; 1726 1727 if (status == IXGBE_SUCCESS) { 1728 eec = IXGBE_READ_REG(hw, IXGBE_EEC); 1729 1730 /* Request EEPROM Access */ 1731 eec |= IXGBE_EEC_REQ; 1732 IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); 1733 1734 for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) { 1735 eec = IXGBE_READ_REG(hw, IXGBE_EEC); 1736 if (eec & IXGBE_EEC_GNT) 1737 break; 1738 usec_delay(5); 1739 } 1740 1741 /* Release if grant not acquired */ 1742 if (!(eec & IXGBE_EEC_GNT)) { 1743 eec &= ~IXGBE_EEC_REQ; 1744 IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); 1745 DEBUGOUT("Could not acquire EEPROM grant\n"); 1746 1747 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); 1748 status = IXGBE_ERR_EEPROM; 1749 } 1750 1751 /* Setup EEPROM for Read/Write */ 1752 if (status == IXGBE_SUCCESS) { 1753 /* Clear CS and SK */ 1754 eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK); 1755 IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); 1756 IXGBE_WRITE_FLUSH(hw); 1757 usec_delay(1); 1758 } 1759 } 1760 return status; 1761 } 1762 1763 /** 1764 * ixgbe_get_eeprom_semaphore - Get hardware semaphore 1765 * @hw: pointer to hardware structure 1766 * 1767 * Sets the hardware semaphores so EEPROM access can occur for bit-bang method 1768 **/ 1769 static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw) 1770 { 1771 s32 status = IXGBE_ERR_EEPROM; 1772 u32 timeout = 2000; 1773 u32 i; 1774 u32 swsm; 1775 1776 DEBUGFUNC("ixgbe_get_eeprom_semaphore"); 1777 1778 1779 /* Get SMBI software semaphore between device drivers first */ 1780 for (i = 0; i < timeout; i++) { 1781 /* 1782 * If the SMBI bit is 0 when we read it, then the bit will be 1783 * set and we have the semaphore 1784 */ 1785 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); 1786 if (!(swsm & IXGBE_SWSM_SMBI)) { 1787 status = IXGBE_SUCCESS; 1788 break; 1789 } 1790 usec_delay(50); 1791 } 1792 1793 if (i == timeout) { 1794 DEBUGOUT("Driver can't access the Eeprom - SMBI Semaphore " 1795 "not granted.\n"); 1796 /* 1797 * this release is particularly important because our attempts 1798 * above to get the semaphore may have succeeded, and if there 1799 * was a timeout, we should unconditionally clear the semaphore 1800 * bits to free the driver to make progress 1801 */ 1802 ixgbe_release_eeprom_semaphore(hw); 1803 1804 usec_delay(50); 1805 /* 1806 * one last try 1807 * If the SMBI bit is 0 when we read it, then the bit will be 1808 * set and we have the semaphore 1809 */ 1810 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); 1811 if (!(swsm & IXGBE_SWSM_SMBI)) 1812 status = IXGBE_SUCCESS; 1813 } 1814 1815 /* Now get the semaphore between SW/FW through the SWESMBI bit */ 1816 if (status == IXGBE_SUCCESS) { 1817 for (i = 0; i < timeout; i++) { 1818 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); 1819 1820 /* Set the SW EEPROM semaphore bit to request access */ 1821 swsm |= IXGBE_SWSM_SWESMBI; 1822 IXGBE_WRITE_REG(hw, IXGBE_SWSM, swsm); 1823 1824 /* 1825 * If we set the bit successfully then we got the 1826 * semaphore. 1827 */ 1828 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); 1829 if (swsm & IXGBE_SWSM_SWESMBI) 1830 break; 1831 1832 usec_delay(50); 1833 } 1834 1835 /* 1836 * Release semaphores and return error if SW EEPROM semaphore 1837 * was not granted because we don't have access to the EEPROM 1838 */ 1839 if (i >= timeout) { 1840 ERROR_REPORT1(IXGBE_ERROR_POLLING, 1841 "SWESMBI Software EEPROM semaphore not granted.\n"); 1842 ixgbe_release_eeprom_semaphore(hw); 1843 status = IXGBE_ERR_EEPROM; 1844 } 1845 } else { 1846 ERROR_REPORT1(IXGBE_ERROR_POLLING, 1847 "Software semaphore SMBI between device drivers " 1848 "not granted.\n"); 1849 } 1850 1851 return status; 1852 } 1853 1854 /** 1855 * ixgbe_release_eeprom_semaphore - Release hardware semaphore 1856 * @hw: pointer to hardware structure 1857 * 1858 * This function clears hardware semaphore bits. 1859 **/ 1860 static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw) 1861 { 1862 u32 swsm; 1863 1864 DEBUGFUNC("ixgbe_release_eeprom_semaphore"); 1865 1866 swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); 1867 1868 /* Release both semaphores by writing 0 to the bits SWESMBI and SMBI */ 1869 swsm &= ~(IXGBE_SWSM_SWESMBI | IXGBE_SWSM_SMBI); 1870 IXGBE_WRITE_REG(hw, IXGBE_SWSM, swsm); 1871 IXGBE_WRITE_FLUSH(hw); 1872 } 1873 1874 /** 1875 * ixgbe_ready_eeprom - Polls for EEPROM ready 1876 * @hw: pointer to hardware structure 1877 **/ 1878 static s32 ixgbe_ready_eeprom(struct ixgbe_hw *hw) 1879 { 1880 s32 status = IXGBE_SUCCESS; 1881 u16 i; 1882 u8 spi_stat_reg; 1883 1884 DEBUGFUNC("ixgbe_ready_eeprom"); 1885 1886 /* 1887 * Read "Status Register" repeatedly until the LSB is cleared. The 1888 * EEPROM will signal that the command has been completed by clearing 1889 * bit 0 of the internal status register. If it's not cleared within 1890 * 5 milliseconds, then error out. 1891 */ 1892 for (i = 0; i < IXGBE_EEPROM_MAX_RETRY_SPI; i += 5) { 1893 ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_RDSR_OPCODE_SPI, 1894 IXGBE_EEPROM_OPCODE_BITS); 1895 spi_stat_reg = (u8)ixgbe_shift_in_eeprom_bits(hw, 8); 1896 if (!(spi_stat_reg & IXGBE_EEPROM_STATUS_RDY_SPI)) 1897 break; 1898 1899 usec_delay(5); 1900 ixgbe_standby_eeprom(hw); 1901 }; 1902 1903 /* 1904 * On some parts, SPI write time could vary from 0-20mSec on 3.3V 1905 * devices (and only 0-5mSec on 5V devices) 1906 */ 1907 if (i >= IXGBE_EEPROM_MAX_RETRY_SPI) { 1908 DEBUGOUT("SPI EEPROM Status error\n"); 1909 status = IXGBE_ERR_EEPROM; 1910 } 1911 1912 return status; 1913 } 1914 1915 /** 1916 * ixgbe_standby_eeprom - Returns EEPROM to a "standby" state 1917 * @hw: pointer to hardware structure 1918 **/ 1919 static void ixgbe_standby_eeprom(struct ixgbe_hw *hw) 1920 { 1921 u32 eec; 1922 1923 DEBUGFUNC("ixgbe_standby_eeprom"); 1924 1925 eec = IXGBE_READ_REG(hw, IXGBE_EEC); 1926 1927 /* Toggle CS to flush commands */ 1928 eec |= IXGBE_EEC_CS; 1929 IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); 1930 IXGBE_WRITE_FLUSH(hw); 1931 usec_delay(1); 1932 eec &= ~IXGBE_EEC_CS; 1933 IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); 1934 IXGBE_WRITE_FLUSH(hw); 1935 usec_delay(1); 1936 } 1937 1938 /** 1939 * ixgbe_shift_out_eeprom_bits - Shift data bits out to the EEPROM. 1940 * @hw: pointer to hardware structure 1941 * @data: data to send to the EEPROM 1942 * @count: number of bits to shift out 1943 **/ 1944 static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, 1945 u16 count) 1946 { 1947 u32 eec; 1948 u32 mask; 1949 u32 i; 1950 1951 DEBUGFUNC("ixgbe_shift_out_eeprom_bits"); 1952 1953 eec = IXGBE_READ_REG(hw, IXGBE_EEC); 1954 1955 /* 1956 * Mask is used to shift "count" bits of "data" out to the EEPROM 1957 * one bit at a time. Determine the starting bit based on count 1958 */ 1959 mask = 0x01 << (count - 1); 1960 1961 for (i = 0; i < count; i++) { 1962 /* 1963 * A "1" is shifted out to the EEPROM by setting bit "DI" to a 1964 * "1", and then raising and then lowering the clock (the SK 1965 * bit controls the clock input to the EEPROM). A "0" is 1966 * shifted out to the EEPROM by setting "DI" to "0" and then 1967 * raising and then lowering the clock. 1968 */ 1969 if (data & mask) 1970 eec |= IXGBE_EEC_DI; 1971 else 1972 eec &= ~IXGBE_EEC_DI; 1973 1974 IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); 1975 IXGBE_WRITE_FLUSH(hw); 1976 1977 usec_delay(1); 1978 1979 ixgbe_raise_eeprom_clk(hw, &eec); 1980 ixgbe_lower_eeprom_clk(hw, &eec); 1981 1982 /* 1983 * Shift mask to signify next bit of data to shift in to the 1984 * EEPROM 1985 */ 1986 mask = mask >> 1; 1987 }; 1988 1989 /* We leave the "DI" bit set to "0" when we leave this routine. */ 1990 eec &= ~IXGBE_EEC_DI; 1991 IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); 1992 IXGBE_WRITE_FLUSH(hw); 1993 } 1994 1995 /** 1996 * ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM 1997 * @hw: pointer to hardware structure 1998 **/ 1999 static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count) 2000 { 2001 u32 eec; 2002 u32 i; 2003 u16 data = 0; 2004 2005 DEBUGFUNC("ixgbe_shift_in_eeprom_bits"); 2006 2007 /* 2008 * In order to read a register from the EEPROM, we need to shift 2009 * 'count' bits in from the EEPROM. Bits are "shifted in" by raising 2010 * the clock input to the EEPROM (setting the SK bit), and then reading 2011 * the value of the "DO" bit. During this "shifting in" process the 2012 * "DI" bit should always be clear. 2013 */ 2014 eec = IXGBE_READ_REG(hw, IXGBE_EEC); 2015 2016 eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI); 2017 2018 for (i = 0; i < count; i++) { 2019 data = data << 1; 2020 ixgbe_raise_eeprom_clk(hw, &eec); 2021 2022 eec = IXGBE_READ_REG(hw, IXGBE_EEC); 2023 2024 eec &= ~(IXGBE_EEC_DI); 2025 if (eec & IXGBE_EEC_DO) 2026 data |= 1; 2027 2028 ixgbe_lower_eeprom_clk(hw, &eec); 2029 } 2030 2031 return data; 2032 } 2033 2034 /** 2035 * ixgbe_raise_eeprom_clk - Raises the EEPROM's clock input. 2036 * @hw: pointer to hardware structure 2037 * @eec: EEC register's current value 2038 **/ 2039 static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) 2040 { 2041 DEBUGFUNC("ixgbe_raise_eeprom_clk"); 2042 2043 /* 2044 * Raise the clock input to the EEPROM 2045 * (setting the SK bit), then delay 2046 */ 2047 *eec = *eec | IXGBE_EEC_SK; 2048 IXGBE_WRITE_REG(hw, IXGBE_EEC, *eec); 2049 IXGBE_WRITE_FLUSH(hw); 2050 usec_delay(1); 2051 } 2052 2053 /** 2054 * ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input. 2055 * @hw: pointer to hardware structure 2056 * @eecd: EECD's current value 2057 **/ 2058 static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) 2059 { 2060 DEBUGFUNC("ixgbe_lower_eeprom_clk"); 2061 2062 /* 2063 * Lower the clock input to the EEPROM (clearing the SK bit), then 2064 * delay 2065 */ 2066 *eec = *eec & ~IXGBE_EEC_SK; 2067 IXGBE_WRITE_REG(hw, IXGBE_EEC, *eec); 2068 IXGBE_WRITE_FLUSH(hw); 2069 usec_delay(1); 2070 } 2071 2072 /** 2073 * ixgbe_release_eeprom - Release EEPROM, release semaphores 2074 * @hw: pointer to hardware structure 2075 **/ 2076 static void ixgbe_release_eeprom(struct ixgbe_hw *hw) 2077 { 2078 u32 eec; 2079 2080 DEBUGFUNC("ixgbe_release_eeprom"); 2081 2082 eec = IXGBE_READ_REG(hw, IXGBE_EEC); 2083 2084 eec |= IXGBE_EEC_CS; /* Pull CS high */ 2085 eec &= ~IXGBE_EEC_SK; /* Lower SCK */ 2086 2087 IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); 2088 IXGBE_WRITE_FLUSH(hw); 2089 2090 usec_delay(1); 2091 2092 /* Stop requesting EEPROM access */ 2093 eec &= ~IXGBE_EEC_REQ; 2094 IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); 2095 2096 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); 2097 2098 /* Delay before attempt to obtain semaphore again to allow FW access */ 2099 msec_delay(hw->eeprom.semaphore_delay); 2100 } 2101 2102 /** 2103 * ixgbe_calc_eeprom_checksum_generic - Calculates and returns the checksum 2104 * @hw: pointer to hardware structure 2105 * 2106 * Returns a negative error code on error, or the 16-bit checksum 2107 **/ 2108 s32 ixgbe_calc_eeprom_checksum_generic(struct ixgbe_hw *hw) 2109 { 2110 u16 i; 2111 u16 j; 2112 u16 checksum = 0; 2113 u16 length = 0; 2114 u16 pointer = 0; 2115 u16 word = 0; 2116 2117 DEBUGFUNC("ixgbe_calc_eeprom_checksum_generic"); 2118 2119 /* Include 0x0-0x3F in the checksum */ 2120 for (i = 0; i < IXGBE_EEPROM_CHECKSUM; i++) { 2121 if (hw->eeprom.ops.read(hw, i, &word)) { 2122 DEBUGOUT("EEPROM read failed\n"); 2123 return IXGBE_ERR_EEPROM; 2124 } 2125 checksum += word; 2126 } 2127 2128 /* Include all data from pointers except for the fw pointer */ 2129 for (i = IXGBE_PCIE_ANALOG_PTR; i < IXGBE_FW_PTR; i++) { 2130 if (hw->eeprom.ops.read(hw, i, &pointer)) { 2131 DEBUGOUT("EEPROM read failed\n"); 2132 return IXGBE_ERR_EEPROM; 2133 } 2134 2135 /* If the pointer seems invalid */ 2136 if (pointer == 0xFFFF || pointer == 0) 2137 continue; 2138 2139 if (hw->eeprom.ops.read(hw, pointer, &length)) { 2140 DEBUGOUT("EEPROM read failed\n"); 2141 return IXGBE_ERR_EEPROM; 2142 } 2143 2144 if (length == 0xFFFF || length == 0) 2145 continue; 2146 2147 for (j = pointer + 1; j <= pointer + length; j++) { 2148 if (hw->eeprom.ops.read(hw, j, &word)) { 2149 DEBUGOUT("EEPROM read failed\n"); 2150 return IXGBE_ERR_EEPROM; 2151 } 2152 checksum += word; 2153 } 2154 } 2155 2156 checksum = (u16)IXGBE_EEPROM_SUM - checksum; 2157 2158 return (s32)checksum; 2159 } 2160 2161 /** 2162 * ixgbe_validate_eeprom_checksum_generic - Validate EEPROM checksum 2163 * @hw: pointer to hardware structure 2164 * @checksum_val: calculated checksum 2165 * 2166 * Performs checksum calculation and validates the EEPROM checksum. If the 2167 * caller does not need checksum_val, the value can be NULL. 2168 **/ 2169 s32 ixgbe_validate_eeprom_checksum_generic(struct ixgbe_hw *hw, 2170 u16 *checksum_val) 2171 { 2172 s32 status; 2173 u16 checksum; 2174 u16 read_checksum = 0; 2175 2176 DEBUGFUNC("ixgbe_validate_eeprom_checksum_generic"); 2177 2178 /* Read the first word from the EEPROM. If this times out or fails, do 2179 * not continue or we could be in for a very long wait while every 2180 * EEPROM read fails 2181 */ 2182 status = hw->eeprom.ops.read(hw, 0, &checksum); 2183 if (status) { 2184 DEBUGOUT("EEPROM read failed\n"); 2185 return status; 2186 } 2187 2188 status = hw->eeprom.ops.calc_checksum(hw); 2189 if (status < 0) 2190 return status; 2191 2192 checksum = (u16)(status & 0xffff); 2193 2194 status = hw->eeprom.ops.read(hw, IXGBE_EEPROM_CHECKSUM, &read_checksum); 2195 if (status) { 2196 DEBUGOUT("EEPROM read failed\n"); 2197 return status; 2198 } 2199 2200 /* Verify read checksum from EEPROM is the same as 2201 * calculated checksum 2202 */ 2203 if (read_checksum != checksum) 2204 status = IXGBE_ERR_EEPROM_CHECKSUM; 2205 2206 /* If the user cares, return the calculated checksum */ 2207 if (checksum_val) 2208 *checksum_val = checksum; 2209 2210 return status; 2211 } 2212 2213 /** 2214 * ixgbe_update_eeprom_checksum_generic - Updates the EEPROM checksum 2215 * @hw: pointer to hardware structure 2216 **/ 2217 s32 ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw *hw) 2218 { 2219 s32 status; 2220 u16 checksum; 2221 2222 DEBUGFUNC("ixgbe_update_eeprom_checksum_generic"); 2223 2224 /* Read the first word from the EEPROM. If this times out or fails, do 2225 * not continue or we could be in for a very long wait while every 2226 * EEPROM read fails 2227 */ 2228 status = hw->eeprom.ops.read(hw, 0, &checksum); 2229 if (status) { 2230 DEBUGOUT("EEPROM read failed\n"); 2231 return status; 2232 } 2233 2234 status = hw->eeprom.ops.calc_checksum(hw); 2235 if (status < 0) 2236 return status; 2237 2238 checksum = (u16)(status & 0xffff); 2239 2240 status = hw->eeprom.ops.write(hw, IXGBE_EEPROM_CHECKSUM, checksum); 2241 2242 return status; 2243 } 2244 2245 /** 2246 * ixgbe_validate_mac_addr - Validate MAC address 2247 * @mac_addr: pointer to MAC address. 2248 * 2249 * Tests a MAC address to ensure it is a valid Individual Address 2250 **/ 2251 s32 ixgbe_validate_mac_addr(u8 *mac_addr) 2252 { 2253 s32 status = IXGBE_SUCCESS; 2254 2255 DEBUGFUNC("ixgbe_validate_mac_addr"); 2256 2257 /* Make sure it is not a multicast address */ 2258 if (IXGBE_IS_MULTICAST(mac_addr)) { 2259 DEBUGOUT("MAC address is multicast\n"); 2260 status = IXGBE_ERR_INVALID_MAC_ADDR; 2261 /* Not a broadcast address */ 2262 } else if (IXGBE_IS_BROADCAST(mac_addr)) { 2263 DEBUGOUT("MAC address is broadcast\n"); 2264 status = IXGBE_ERR_INVALID_MAC_ADDR; 2265 /* Reject the zero address */ 2266 } else if (mac_addr[0] == 0 && mac_addr[1] == 0 && mac_addr[2] == 0 && 2267 mac_addr[3] == 0 && mac_addr[4] == 0 && mac_addr[5] == 0) { 2268 DEBUGOUT("MAC address is all zeros\n"); 2269 status = IXGBE_ERR_INVALID_MAC_ADDR; 2270 } 2271 return status; 2272 } 2273 2274 /** 2275 * ixgbe_set_rar_generic - Set Rx address register 2276 * @hw: pointer to hardware structure 2277 * @index: Receive address register to write 2278 * @addr: Address to put into receive address register 2279 * @vmdq: VMDq "set" or "pool" index 2280 * @enable_addr: set flag that address is active 2281 * 2282 * Puts an ethernet address into a receive address register. 2283 **/ 2284 s32 ixgbe_set_rar_generic(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vmdq, 2285 u32 enable_addr) 2286 { 2287 u32 rar_low, rar_high; 2288 u32 rar_entries = hw->mac.num_rar_entries; 2289 2290 DEBUGFUNC("ixgbe_set_rar_generic"); 2291 2292 /* Make sure we are using a valid rar index range */ 2293 if (index >= rar_entries) { 2294 ERROR_REPORT2(IXGBE_ERROR_ARGUMENT, 2295 "RAR index %d is out of range.\n", index); 2296 return IXGBE_ERR_INVALID_ARGUMENT; 2297 } 2298 2299 /* setup VMDq pool selection before this RAR gets enabled */ 2300 hw->mac.ops.set_vmdq(hw, index, vmdq); 2301 2302 /* 2303 * HW expects these in little endian so we reverse the byte 2304 * order from network order (big endian) to little endian 2305 */ 2306 rar_low = ((u32)addr[0] | 2307 ((u32)addr[1] << 8) | 2308 ((u32)addr[2] << 16) | 2309 ((u32)addr[3] << 24)); 2310 /* 2311 * Some parts put the VMDq setting in the extra RAH bits, 2312 * so save everything except the lower 16 bits that hold part 2313 * of the address and the address valid bit. 2314 */ 2315 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); 2316 rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); 2317 rar_high |= ((u32)addr[4] | ((u32)addr[5] << 8)); 2318 2319 if (enable_addr != 0) 2320 rar_high |= IXGBE_RAH_AV; 2321 2322 IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low); 2323 IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); 2324 2325 return IXGBE_SUCCESS; 2326 } 2327 2328 /** 2329 * ixgbe_clear_rar_generic - Remove Rx address register 2330 * @hw: pointer to hardware structure 2331 * @index: Receive address register to write 2332 * 2333 * Clears an ethernet address from a receive address register. 2334 **/ 2335 s32 ixgbe_clear_rar_generic(struct ixgbe_hw *hw, u32 index) 2336 { 2337 u32 rar_high; 2338 u32 rar_entries = hw->mac.num_rar_entries; 2339 2340 DEBUGFUNC("ixgbe_clear_rar_generic"); 2341 2342 /* Make sure we are using a valid rar index range */ 2343 if (index >= rar_entries) { 2344 ERROR_REPORT2(IXGBE_ERROR_ARGUMENT, 2345 "RAR index %d is out of range.\n", index); 2346 return IXGBE_ERR_INVALID_ARGUMENT; 2347 } 2348 2349 /* 2350 * Some parts put the VMDq setting in the extra RAH bits, 2351 * so save everything except the lower 16 bits that hold part 2352 * of the address and the address valid bit. 2353 */ 2354 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); 2355 rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); 2356 2357 IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0); 2358 IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); 2359 2360 /* clear VMDq pool/queue selection for this RAR */ 2361 hw->mac.ops.clear_vmdq(hw, index, IXGBE_CLEAR_VMDQ_ALL); 2362 2363 return IXGBE_SUCCESS; 2364 } 2365 2366 /** 2367 * ixgbe_init_rx_addrs_generic - Initializes receive address filters. 2368 * @hw: pointer to hardware structure 2369 * 2370 * Places the MAC address in receive address register 0 and clears the rest 2371 * of the receive address registers. Clears the multicast table. Assumes 2372 * the receiver is in reset when the routine is called. 2373 **/ 2374 s32 ixgbe_init_rx_addrs_generic(struct ixgbe_hw *hw) 2375 { 2376 u32 i; 2377 u32 rar_entries = hw->mac.num_rar_entries; 2378 2379 DEBUGFUNC("ixgbe_init_rx_addrs_generic"); 2380 2381 /* 2382 * If the current mac address is valid, assume it is a software override 2383 * to the permanent address. 2384 * Otherwise, use the permanent address from the eeprom. 2385 */ 2386 if (ixgbe_validate_mac_addr(hw->mac.addr) == 2387 IXGBE_ERR_INVALID_MAC_ADDR) { 2388 /* Get the MAC address from the RAR0 for later reference */ 2389 hw->mac.ops.get_mac_addr(hw, hw->mac.addr); 2390 2391 DEBUGOUT3(" Keeping Current RAR0 Addr =%.2X %.2X %.2X ", 2392 hw->mac.addr[0], hw->mac.addr[1], 2393 hw->mac.addr[2]); 2394 DEBUGOUT3("%.2X %.2X %.2X\n", hw->mac.addr[3], 2395 hw->mac.addr[4], hw->mac.addr[5]); 2396 } else { 2397 /* Setup the receive address. */ 2398 DEBUGOUT("Overriding MAC Address in RAR[0]\n"); 2399 DEBUGOUT3(" New MAC Addr =%.2X %.2X %.2X ", 2400 hw->mac.addr[0], hw->mac.addr[1], 2401 hw->mac.addr[2]); 2402 DEBUGOUT3("%.2X %.2X %.2X\n", hw->mac.addr[3], 2403 hw->mac.addr[4], hw->mac.addr[5]); 2404 2405 hw->mac.ops.set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV); 2406 2407 /* clear VMDq pool/queue selection for RAR 0 */ 2408 hw->mac.ops.clear_vmdq(hw, 0, IXGBE_CLEAR_VMDQ_ALL); 2409 } 2410 hw->addr_ctrl.overflow_promisc = 0; 2411 2412 hw->addr_ctrl.rar_used_count = 1; 2413 2414 /* Zero out the other receive addresses. */ 2415 DEBUGOUT1("Clearing RAR[1-%d]\n", rar_entries - 1); 2416 for (i = 1; i < rar_entries; i++) { 2417 IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0); 2418 IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0); 2419 } 2420 2421 /* Clear the MTA */ 2422 hw->addr_ctrl.mta_in_use = 0; 2423 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type); 2424 2425 DEBUGOUT(" Clearing MTA\n"); 2426 for (i = 0; i < hw->mac.mcft_size; i++) 2427 IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0); 2428 2429 ixgbe_init_uta_tables(hw); 2430 2431 return IXGBE_SUCCESS; 2432 } 2433 2434 /** 2435 * ixgbe_add_uc_addr - Adds a secondary unicast address. 2436 * @hw: pointer to hardware structure 2437 * @addr: new address 2438 * 2439 * Adds it to unused receive address register or goes into promiscuous mode. 2440 **/ 2441 void ixgbe_add_uc_addr(struct ixgbe_hw *hw, u8 *addr, u32 vmdq) 2442 { 2443 u32 rar_entries = hw->mac.num_rar_entries; 2444 u32 rar; 2445 2446 DEBUGFUNC("ixgbe_add_uc_addr"); 2447 2448 DEBUGOUT6(" UC Addr = %.2X %.2X %.2X %.2X %.2X %.2X\n", 2449 addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]); 2450 2451 /* 2452 * Place this address in the RAR if there is room, 2453 * else put the controller into promiscuous mode 2454 */ 2455 if (hw->addr_ctrl.rar_used_count < rar_entries) { 2456 rar = hw->addr_ctrl.rar_used_count; 2457 hw->mac.ops.set_rar(hw, rar, addr, vmdq, IXGBE_RAH_AV); 2458 DEBUGOUT1("Added a secondary address to RAR[%d]\n", rar); 2459 hw->addr_ctrl.rar_used_count++; 2460 } else { 2461 hw->addr_ctrl.overflow_promisc++; 2462 } 2463 2464 DEBUGOUT("ixgbe_add_uc_addr Complete\n"); 2465 } 2466 2467 /** 2468 * ixgbe_update_uc_addr_list_generic - Updates MAC list of secondary addresses 2469 * @hw: pointer to hardware structure 2470 * @addr_list: the list of new addresses 2471 * @addr_count: number of addresses 2472 * @next: iterator function to walk the address list 2473 * 2474 * The given list replaces any existing list. Clears the secondary addrs from 2475 * receive address registers. Uses unused receive address registers for the 2476 * first secondary addresses, and falls back to promiscuous mode as needed. 2477 * 2478 * Drivers using secondary unicast addresses must set user_set_promisc when 2479 * manually putting the device into promiscuous mode. 2480 **/ 2481 s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw, u8 *addr_list, 2482 u32 addr_count, ixgbe_mc_addr_itr next) 2483 { 2484 u8 *addr; 2485 u32 i; 2486 u32 old_promisc_setting = hw->addr_ctrl.overflow_promisc; 2487 u32 uc_addr_in_use; 2488 u32 fctrl; 2489 u32 vmdq; 2490 2491 DEBUGFUNC("ixgbe_update_uc_addr_list_generic"); 2492 2493 /* 2494 * Clear accounting of old secondary address list, 2495 * don't count RAR[0] 2496 */ 2497 uc_addr_in_use = hw->addr_ctrl.rar_used_count - 1; 2498 hw->addr_ctrl.rar_used_count -= uc_addr_in_use; 2499 hw->addr_ctrl.overflow_promisc = 0; 2500 2501 /* Zero out the other receive addresses */ 2502 DEBUGOUT1("Clearing RAR[1-%d]\n", uc_addr_in_use+1); 2503 for (i = 0; i < uc_addr_in_use; i++) { 2504 IXGBE_WRITE_REG(hw, IXGBE_RAL(1+i), 0); 2505 IXGBE_WRITE_REG(hw, IXGBE_RAH(1+i), 0); 2506 } 2507 2508 /* Add the new addresses */ 2509 for (i = 0; i < addr_count; i++) { 2510 DEBUGOUT(" Adding the secondary addresses:\n"); 2511 addr = next(hw, &addr_list, &vmdq); 2512 ixgbe_add_uc_addr(hw, addr, vmdq); 2513 } 2514 2515 if (hw->addr_ctrl.overflow_promisc) { 2516 /* enable promisc if not already in overflow or set by user */ 2517 if (!old_promisc_setting && !hw->addr_ctrl.user_set_promisc) { 2518 DEBUGOUT(" Entering address overflow promisc mode\n"); 2519 fctrl = IXGBE_READ_REG(hw, IXGBE_FCTRL); 2520 fctrl |= IXGBE_FCTRL_UPE; 2521 IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl); 2522 } 2523 } else { 2524 /* only disable if set by overflow, not by user */ 2525 if (old_promisc_setting && !hw->addr_ctrl.user_set_promisc) { 2526 DEBUGOUT(" Leaving address overflow promisc mode\n"); 2527 fctrl = IXGBE_READ_REG(hw, IXGBE_FCTRL); 2528 fctrl &= ~IXGBE_FCTRL_UPE; 2529 IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl); 2530 } 2531 } 2532 2533 DEBUGOUT("ixgbe_update_uc_addr_list_generic Complete\n"); 2534 return IXGBE_SUCCESS; 2535 } 2536 2537 /** 2538 * ixgbe_mta_vector - Determines bit-vector in multicast table to set 2539 * @hw: pointer to hardware structure 2540 * @mc_addr: the multicast address 2541 * 2542 * Extracts the 12 bits, from a multicast address, to determine which 2543 * bit-vector to set in the multicast table. The hardware uses 12 bits, from 2544 * incoming rx multicast addresses, to determine the bit-vector to check in 2545 * the MTA. Which of the 4 combination, of 12-bits, the hardware uses is set 2546 * by the MO field of the MCSTCTRL. The MO field is set during initialization 2547 * to mc_filter_type. 2548 **/ 2549 static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr) 2550 { 2551 u32 vector = 0; 2552 2553 DEBUGFUNC("ixgbe_mta_vector"); 2554 2555 switch (hw->mac.mc_filter_type) { 2556 case 0: /* use bits [47:36] of the address */ 2557 vector = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4)); 2558 break; 2559 case 1: /* use bits [46:35] of the address */ 2560 vector = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5)); 2561 break; 2562 case 2: /* use bits [45:34] of the address */ 2563 vector = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6)); 2564 break; 2565 case 3: /* use bits [43:32] of the address */ 2566 vector = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8)); 2567 break; 2568 default: /* Invalid mc_filter_type */ 2569 DEBUGOUT("MC filter type param set incorrectly\n"); 2570 ASSERT(0); 2571 break; 2572 } 2573 2574 /* vector can only be 12-bits or boundary will be exceeded */ 2575 vector &= 0xFFF; 2576 return vector; 2577 } 2578 2579 /** 2580 * ixgbe_set_mta - Set bit-vector in multicast table 2581 * @hw: pointer to hardware structure 2582 * @hash_value: Multicast address hash value 2583 * 2584 * Sets the bit-vector in the multicast table. 2585 **/ 2586 void ixgbe_set_mta(struct ixgbe_hw *hw, u8 *mc_addr) 2587 { 2588 u32 vector; 2589 u32 vector_bit; 2590 u32 vector_reg; 2591 2592 DEBUGFUNC("ixgbe_set_mta"); 2593 2594 hw->addr_ctrl.mta_in_use++; 2595 2596 vector = ixgbe_mta_vector(hw, mc_addr); 2597 DEBUGOUT1(" bit-vector = 0x%03X\n", vector); 2598 2599 /* 2600 * The MTA is a register array of 128 32-bit registers. It is treated 2601 * like an array of 4096 bits. We want to set bit 2602 * BitArray[vector_value]. So we figure out what register the bit is 2603 * in, read it, OR in the new bit, then write back the new value. The 2604 * register is determined by the upper 7 bits of the vector value and 2605 * the bit within that register are determined by the lower 5 bits of 2606 * the value. 2607 */ 2608 vector_reg = (vector >> 5) & 0x7F; 2609 vector_bit = vector & 0x1F; 2610 hw->mac.mta_shadow[vector_reg] |= (1 << vector_bit); 2611 } 2612 2613 /** 2614 * ixgbe_update_mc_addr_list_generic - Updates MAC list of multicast addresses 2615 * @hw: pointer to hardware structure 2616 * @mc_addr_list: the list of new multicast addresses 2617 * @mc_addr_count: number of addresses 2618 * @next: iterator function to walk the multicast address list 2619 * @clear: flag, when set clears the table beforehand 2620 * 2621 * When the clear flag is set, the given list replaces any existing list. 2622 * Hashes the given addresses into the multicast table. 2623 **/ 2624 s32 ixgbe_update_mc_addr_list_generic(struct ixgbe_hw *hw, u8 *mc_addr_list, 2625 u32 mc_addr_count, ixgbe_mc_addr_itr next, 2626 bool clear) 2627 { 2628 u32 i; 2629 u32 vmdq; 2630 2631 DEBUGFUNC("ixgbe_update_mc_addr_list_generic"); 2632 2633 /* 2634 * Set the new number of MC addresses that we are being requested to 2635 * use. 2636 */ 2637 hw->addr_ctrl.num_mc_addrs = mc_addr_count; 2638 hw->addr_ctrl.mta_in_use = 0; 2639 2640 /* Clear mta_shadow */ 2641 if (clear) { 2642 DEBUGOUT(" Clearing MTA\n"); 2643 memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow)); 2644 } 2645 2646 /* Update mta_shadow */ 2647 for (i = 0; i < mc_addr_count; i++) { 2648 DEBUGOUT(" Adding the multicast addresses:\n"); 2649 ixgbe_set_mta(hw, next(hw, &mc_addr_list, &vmdq)); 2650 } 2651 2652 /* Enable mta */ 2653 for (i = 0; i < hw->mac.mcft_size; i++) 2654 IXGBE_WRITE_REG_ARRAY(hw, IXGBE_MTA(0), i, 2655 hw->mac.mta_shadow[i]); 2656 2657 if (hw->addr_ctrl.mta_in_use > 0) 2658 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, 2659 IXGBE_MCSTCTRL_MFE | hw->mac.mc_filter_type); 2660 2661 DEBUGOUT("ixgbe_update_mc_addr_list_generic Complete\n"); 2662 return IXGBE_SUCCESS; 2663 } 2664 2665 /** 2666 * ixgbe_enable_mc_generic - Enable multicast address in RAR 2667 * @hw: pointer to hardware structure 2668 * 2669 * Enables multicast address in RAR and the use of the multicast hash table. 2670 **/ 2671 s32 ixgbe_enable_mc_generic(struct ixgbe_hw *hw) 2672 { 2673 struct ixgbe_addr_filter_info *a = &hw->addr_ctrl; 2674 2675 DEBUGFUNC("ixgbe_enable_mc_generic"); 2676 2677 if (a->mta_in_use > 0) 2678 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, IXGBE_MCSTCTRL_MFE | 2679 hw->mac.mc_filter_type); 2680 2681 return IXGBE_SUCCESS; 2682 } 2683 2684 /** 2685 * ixgbe_disable_mc_generic - Disable multicast address in RAR 2686 * @hw: pointer to hardware structure 2687 * 2688 * Disables multicast address in RAR and the use of the multicast hash table. 2689 **/ 2690 s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw) 2691 { 2692 struct ixgbe_addr_filter_info *a = &hw->addr_ctrl; 2693 2694 DEBUGFUNC("ixgbe_disable_mc_generic"); 2695 2696 if (a->mta_in_use > 0) 2697 IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type); 2698 2699 return IXGBE_SUCCESS; 2700 } 2701 2702 /** 2703 * ixgbe_fc_enable_generic - Enable flow control 2704 * @hw: pointer to hardware structure 2705 * 2706 * Enable flow control according to the current settings. 2707 **/ 2708 s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw) 2709 { 2710 s32 ret_val = IXGBE_SUCCESS; 2711 u32 mflcn_reg, fccfg_reg; 2712 u32 reg; 2713 u32 fcrtl, fcrth; 2714 int i; 2715 2716 DEBUGFUNC("ixgbe_fc_enable_generic"); 2717 2718 /* Validate the water mark configuration */ 2719 if (!hw->fc.pause_time) { 2720 ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; 2721 goto out; 2722 } 2723 2724 /* Low water mark of zero causes XOFF floods */ 2725 for (i = 0; i < IXGBE_DCB_MAX_TRAFFIC_CLASS; i++) { 2726 if ((hw->fc.current_mode & ixgbe_fc_tx_pause) && 2727 hw->fc.high_water[i]) { 2728 if (!hw->fc.low_water[i] || 2729 hw->fc.low_water[i] >= hw->fc.high_water[i]) { 2730 DEBUGOUT("Invalid water mark configuration\n"); 2731 ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; 2732 goto out; 2733 } 2734 } 2735 } 2736 2737 /* Negotiate the fc mode to use */ 2738 ixgbe_fc_autoneg(hw); 2739 2740 /* Disable any previous flow control settings */ 2741 mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN); 2742 mflcn_reg &= ~(IXGBE_MFLCN_RPFCE_MASK | IXGBE_MFLCN_RFCE); 2743 2744 fccfg_reg = IXGBE_READ_REG(hw, IXGBE_FCCFG); 2745 fccfg_reg &= ~(IXGBE_FCCFG_TFCE_802_3X | IXGBE_FCCFG_TFCE_PRIORITY); 2746 2747 /* 2748 * The possible values of fc.current_mode are: 2749 * 0: Flow control is completely disabled 2750 * 1: Rx flow control is enabled (we can receive pause frames, 2751 * but not send pause frames). 2752 * 2: Tx flow control is enabled (we can send pause frames but 2753 * we do not support receiving pause frames). 2754 * 3: Both Rx and Tx flow control (symmetric) are enabled. 2755 * other: Invalid. 2756 */ 2757 switch (hw->fc.current_mode) { 2758 case ixgbe_fc_none: 2759 /* 2760 * Flow control is disabled by software override or autoneg. 2761 * The code below will actually disable it in the HW. 2762 */ 2763 break; 2764 case ixgbe_fc_rx_pause: 2765 /* 2766 * Rx Flow control is enabled and Tx Flow control is 2767 * disabled by software override. Since there really 2768 * isn't a way to advertise that we are capable of RX 2769 * Pause ONLY, we will advertise that we support both 2770 * symmetric and asymmetric Rx PAUSE. Later, we will 2771 * disable the adapter's ability to send PAUSE frames. 2772 */ 2773 mflcn_reg |= IXGBE_MFLCN_RFCE; 2774 break; 2775 case ixgbe_fc_tx_pause: 2776 /* 2777 * Tx Flow control is enabled, and Rx Flow control is 2778 * disabled by software override. 2779 */ 2780 fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X; 2781 break; 2782 case ixgbe_fc_full: 2783 /* Flow control (both Rx and Tx) is enabled by SW override. */ 2784 mflcn_reg |= IXGBE_MFLCN_RFCE; 2785 fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X; 2786 break; 2787 default: 2788 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, 2789 "Flow control param set incorrectly\n"); 2790 ret_val = IXGBE_ERR_CONFIG; 2791 goto out; 2792 break; 2793 } 2794 2795 /* Set 802.3x based flow control settings. */ 2796 mflcn_reg |= IXGBE_MFLCN_DPF; 2797 IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg); 2798 IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg); 2799 2800 2801 /* Set up and enable Rx high/low water mark thresholds, enable XON. */ 2802 for (i = 0; i < IXGBE_DCB_MAX_TRAFFIC_CLASS; i++) { 2803 if ((hw->fc.current_mode & ixgbe_fc_tx_pause) && 2804 hw->fc.high_water[i]) { 2805 fcrtl = (hw->fc.low_water[i] << 10) | IXGBE_FCRTL_XONE; 2806 IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), fcrtl); 2807 fcrth = (hw->fc.high_water[i] << 10) | IXGBE_FCRTH_FCEN; 2808 } else { 2809 IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), 0); 2810 /* 2811 * In order to prevent Tx hangs when the internal Tx 2812 * switch is enabled we must set the high water mark 2813 * to the Rx packet buffer size - 24KB. This allows 2814 * the Tx switch to function even under heavy Rx 2815 * workloads. 2816 */ 2817 fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576; 2818 } 2819 2820 IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth); 2821 } 2822 2823 /* Configure pause time (2 TCs per register) */ 2824 reg = hw->fc.pause_time * 0x00010001; 2825 for (i = 0; i < (IXGBE_DCB_MAX_TRAFFIC_CLASS / 2); i++) 2826 IXGBE_WRITE_REG(hw, IXGBE_FCTTV(i), reg); 2827 2828 /* Configure flow control refresh threshold value */ 2829 IXGBE_WRITE_REG(hw, IXGBE_FCRTV, hw->fc.pause_time / 2); 2830 2831 out: 2832 return ret_val; 2833 } 2834 2835 /** 2836 * ixgbe_negotiate_fc - Negotiate flow control 2837 * @hw: pointer to hardware structure 2838 * @adv_reg: flow control advertised settings 2839 * @lp_reg: link partner's flow control settings 2840 * @adv_sym: symmetric pause bit in advertisement 2841 * @adv_asm: asymmetric pause bit in advertisement 2842 * @lp_sym: symmetric pause bit in link partner advertisement 2843 * @lp_asm: asymmetric pause bit in link partner advertisement 2844 * 2845 * Find the intersection between advertised settings and link partner's 2846 * advertised settings 2847 **/ 2848 static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg, 2849 u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm) 2850 { 2851 if ((!(adv_reg)) || (!(lp_reg))) { 2852 ERROR_REPORT3(IXGBE_ERROR_UNSUPPORTED, 2853 "Local or link partner's advertised flow control " 2854 "settings are NULL. Local: %x, link partner: %x\n", 2855 adv_reg, lp_reg); 2856 return IXGBE_ERR_FC_NOT_NEGOTIATED; 2857 } 2858 2859 if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) { 2860 /* 2861 * Now we need to check if the user selected Rx ONLY 2862 * of pause frames. In this case, we had to advertise 2863 * FULL flow control because we could not advertise RX 2864 * ONLY. Hence, we must now check to see if we need to 2865 * turn OFF the TRANSMISSION of PAUSE frames. 2866 */ 2867 if (hw->fc.requested_mode == ixgbe_fc_full) { 2868 hw->fc.current_mode = ixgbe_fc_full; 2869 DEBUGOUT("Flow Control = FULL.\n"); 2870 } else { 2871 hw->fc.current_mode = ixgbe_fc_rx_pause; 2872 DEBUGOUT("Flow Control=RX PAUSE frames only\n"); 2873 } 2874 } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) && 2875 (lp_reg & lp_sym) && (lp_reg & lp_asm)) { 2876 hw->fc.current_mode = ixgbe_fc_tx_pause; 2877 DEBUGOUT("Flow Control = TX PAUSE frames only.\n"); 2878 } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) && 2879 !(lp_reg & lp_sym) && (lp_reg & lp_asm)) { 2880 hw->fc.current_mode = ixgbe_fc_rx_pause; 2881 DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); 2882 } else { 2883 hw->fc.current_mode = ixgbe_fc_none; 2884 DEBUGOUT("Flow Control = NONE.\n"); 2885 } 2886 return IXGBE_SUCCESS; 2887 } 2888 2889 /** 2890 * ixgbe_fc_autoneg_fiber - Enable flow control on 1 gig fiber 2891 * @hw: pointer to hardware structure 2892 * 2893 * Enable flow control according on 1 gig fiber. 2894 **/ 2895 static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw) 2896 { 2897 u32 pcs_anadv_reg, pcs_lpab_reg, linkstat; 2898 s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; 2899 2900 /* 2901 * On multispeed fiber at 1g, bail out if 2902 * - link is up but AN did not complete, or if 2903 * - link is up and AN completed but timed out 2904 */ 2905 2906 linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA); 2907 if ((!!(linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) || 2908 (!!(linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) { 2909 DEBUGOUT("Auto-Negotiation did not complete or timed out\n"); 2910 goto out; 2911 } 2912 2913 pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); 2914 pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP); 2915 2916 ret_val = ixgbe_negotiate_fc(hw, pcs_anadv_reg, 2917 pcs_lpab_reg, IXGBE_PCS1GANA_SYM_PAUSE, 2918 IXGBE_PCS1GANA_ASM_PAUSE, 2919 IXGBE_PCS1GANA_SYM_PAUSE, 2920 IXGBE_PCS1GANA_ASM_PAUSE); 2921 2922 out: 2923 return ret_val; 2924 } 2925 2926 /** 2927 * ixgbe_fc_autoneg_backplane - Enable flow control IEEE clause 37 2928 * @hw: pointer to hardware structure 2929 * 2930 * Enable flow control according to IEEE clause 37. 2931 **/ 2932 static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw) 2933 { 2934 u32 links2, anlp1_reg, autoc_reg, links; 2935 s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; 2936 2937 /* 2938 * On backplane, bail out if 2939 * - backplane autoneg was not completed, or if 2940 * - we are 82599 and link partner is not AN enabled 2941 */ 2942 links = IXGBE_READ_REG(hw, IXGBE_LINKS); 2943 if ((links & IXGBE_LINKS_KX_AN_COMP) == 0) { 2944 DEBUGOUT("Auto-Negotiation did not complete\n"); 2945 goto out; 2946 } 2947 2948 if (hw->mac.type == ixgbe_mac_82599EB) { 2949 links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2); 2950 if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0) { 2951 DEBUGOUT("Link partner is not AN enabled\n"); 2952 goto out; 2953 } 2954 } 2955 /* 2956 * Read the 10g AN autoc and LP ability registers and resolve 2957 * local flow control settings accordingly 2958 */ 2959 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); 2960 anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1); 2961 2962 ret_val = ixgbe_negotiate_fc(hw, autoc_reg, 2963 anlp1_reg, IXGBE_AUTOC_SYM_PAUSE, IXGBE_AUTOC_ASM_PAUSE, 2964 IXGBE_ANLP1_SYM_PAUSE, IXGBE_ANLP1_ASM_PAUSE); 2965 2966 out: 2967 return ret_val; 2968 } 2969 2970 /** 2971 * ixgbe_fc_autoneg_copper - Enable flow control IEEE clause 37 2972 * @hw: pointer to hardware structure 2973 * 2974 * Enable flow control according to IEEE clause 37. 2975 **/ 2976 static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw) 2977 { 2978 u16 technology_ability_reg = 0; 2979 u16 lp_technology_ability_reg = 0; 2980 2981 hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_ADVT, 2982 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 2983 &technology_ability_reg); 2984 hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_LP, 2985 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 2986 &lp_technology_ability_reg); 2987 2988 return ixgbe_negotiate_fc(hw, (u32)technology_ability_reg, 2989 (u32)lp_technology_ability_reg, 2990 IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE, 2991 IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE); 2992 } 2993 2994 /** 2995 * ixgbe_fc_autoneg - Configure flow control 2996 * @hw: pointer to hardware structure 2997 * 2998 * Compares our advertised flow control capabilities to those advertised by 2999 * our link partner, and determines the proper flow control mode to use. 3000 **/ 3001 void ixgbe_fc_autoneg(struct ixgbe_hw *hw) 3002 { 3003 s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; 3004 ixgbe_link_speed speed; 3005 bool link_up; 3006 3007 DEBUGFUNC("ixgbe_fc_autoneg"); 3008 3009 /* 3010 * AN should have completed when the cable was plugged in. 3011 * Look for reasons to bail out. Bail out if: 3012 * - FC autoneg is disabled, or if 3013 * - link is not up. 3014 */ 3015 if (hw->fc.disable_fc_autoneg) { 3016 ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, 3017 "Flow control autoneg is disabled"); 3018 goto out; 3019 } 3020 3021 hw->mac.ops.check_link(hw, &speed, &link_up, FALSE); 3022 if (!link_up) { 3023 ERROR_REPORT1(IXGBE_ERROR_SOFTWARE, "The link is down"); 3024 goto out; 3025 } 3026 3027 switch (hw->phy.media_type) { 3028 /* Autoneg flow control on fiber adapters */ 3029 case ixgbe_media_type_fiber_fixed: 3030 case ixgbe_media_type_fiber_qsfp: 3031 case ixgbe_media_type_fiber: 3032 if (speed == IXGBE_LINK_SPEED_1GB_FULL) 3033 ret_val = ixgbe_fc_autoneg_fiber(hw); 3034 break; 3035 3036 /* Autoneg flow control on backplane adapters */ 3037 case ixgbe_media_type_backplane: 3038 ret_val = ixgbe_fc_autoneg_backplane(hw); 3039 break; 3040 3041 /* Autoneg flow control on copper adapters */ 3042 case ixgbe_media_type_copper: 3043 if (ixgbe_device_supports_autoneg_fc(hw)) 3044 ret_val = ixgbe_fc_autoneg_copper(hw); 3045 break; 3046 3047 default: 3048 break; 3049 } 3050 3051 out: 3052 if (ret_val == IXGBE_SUCCESS) { 3053 hw->fc.fc_was_autonegged = TRUE; 3054 } else { 3055 hw->fc.fc_was_autonegged = FALSE; 3056 hw->fc.current_mode = hw->fc.requested_mode; 3057 } 3058 } 3059 3060 /* 3061 * ixgbe_pcie_timeout_poll - Return number of times to poll for completion 3062 * @hw: pointer to hardware structure 3063 * 3064 * System-wide timeout range is encoded in PCIe Device Control2 register. 3065 * 3066 * Add 10% to specified maximum and return the number of times to poll for 3067 * completion timeout, in units of 100 microsec. Never return less than 3068 * 800 = 80 millisec. 3069 */ 3070 static u32 ixgbe_pcie_timeout_poll(struct ixgbe_hw *hw) 3071 { 3072 s16 devctl2; 3073 u32 pollcnt; 3074 3075 devctl2 = IXGBE_READ_PCIE_WORD(hw, IXGBE_PCI_DEVICE_CONTROL2); 3076 devctl2 &= IXGBE_PCIDEVCTRL2_TIMEO_MASK; 3077 3078 switch (devctl2) { 3079 case IXGBE_PCIDEVCTRL2_65_130ms: 3080 pollcnt = 1300; /* 130 millisec */ 3081 break; 3082 case IXGBE_PCIDEVCTRL2_260_520ms: 3083 pollcnt = 5200; /* 520 millisec */ 3084 break; 3085 case IXGBE_PCIDEVCTRL2_1_2s: 3086 pollcnt = 20000; /* 2 sec */ 3087 break; 3088 case IXGBE_PCIDEVCTRL2_4_8s: 3089 pollcnt = 80000; /* 8 sec */ 3090 break; 3091 case IXGBE_PCIDEVCTRL2_17_34s: 3092 pollcnt = 34000; /* 34 sec */ 3093 break; 3094 case IXGBE_PCIDEVCTRL2_50_100us: /* 100 microsecs */ 3095 case IXGBE_PCIDEVCTRL2_1_2ms: /* 2 millisecs */ 3096 case IXGBE_PCIDEVCTRL2_16_32ms: /* 32 millisec */ 3097 case IXGBE_PCIDEVCTRL2_16_32ms_def: /* 32 millisec default */ 3098 default: 3099 pollcnt = 800; /* 80 millisec minimum */ 3100 break; 3101 } 3102 3103 /* add 10% to spec maximum */ 3104 return (pollcnt * 11) / 10; 3105 } 3106 3107 /** 3108 * ixgbe_disable_pcie_master - Disable PCI-express master access 3109 * @hw: pointer to hardware structure 3110 * 3111 * Disables PCI-Express master access and verifies there are no pending 3112 * requests. IXGBE_ERR_MASTER_REQUESTS_PENDING is returned if master disable 3113 * bit hasn't caused the master requests to be disabled, else IXGBE_SUCCESS 3114 * is returned signifying master requests disabled. 3115 **/ 3116 s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw) 3117 { 3118 s32 status = IXGBE_SUCCESS; 3119 u32 i, poll; 3120 u16 value; 3121 3122 DEBUGFUNC("ixgbe_disable_pcie_master"); 3123 3124 /* Always set this bit to ensure any future transactions are blocked */ 3125 IXGBE_WRITE_REG(hw, IXGBE_CTRL, IXGBE_CTRL_GIO_DIS); 3126 3127 /* Exit if master requests are blocked */ 3128 if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO) || 3129 IXGBE_REMOVED(hw->hw_addr)) 3130 goto out; 3131 3132 /* Poll for master request bit to clear */ 3133 for (i = 0; i < IXGBE_PCI_MASTER_DISABLE_TIMEOUT; i++) { 3134 usec_delay(100); 3135 if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO)) 3136 goto out; 3137 } 3138 3139 /* 3140 * Two consecutive resets are required via CTRL.RST per datasheet 3141 * 5.2.5.3.2 Master Disable. We set a flag to inform the reset routine 3142 * of this need. The first reset prevents new master requests from 3143 * being issued by our device. We then must wait 1usec or more for any 3144 * remaining completions from the PCIe bus to trickle in, and then reset 3145 * again to clear out any effects they may have had on our device. 3146 */ 3147 DEBUGOUT("GIO Master Disable bit didn't clear - requesting resets\n"); 3148 hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED; 3149 3150 /* 3151 * Before proceeding, make sure that the PCIe block does not have 3152 * transactions pending. 3153 */ 3154 poll = ixgbe_pcie_timeout_poll(hw); 3155 for (i = 0; i < poll; i++) { 3156 usec_delay(100); 3157 value = IXGBE_READ_PCIE_WORD(hw, IXGBE_PCI_DEVICE_STATUS); 3158 if (IXGBE_REMOVED(hw->hw_addr)) 3159 goto out; 3160 if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING)) 3161 goto out; 3162 } 3163 3164 ERROR_REPORT1(IXGBE_ERROR_POLLING, 3165 "PCIe transaction pending bit also did not clear.\n"); 3166 status = IXGBE_ERR_MASTER_REQUESTS_PENDING; 3167 3168 out: 3169 return status; 3170 } 3171 3172 /** 3173 * ixgbe_acquire_swfw_sync - Acquire SWFW semaphore 3174 * @hw: pointer to hardware structure 3175 * @mask: Mask to specify which semaphore to acquire 3176 * 3177 * Acquires the SWFW semaphore through the GSSR register for the specified 3178 * function (CSR, PHY0, PHY1, EEPROM, Flash) 3179 **/ 3180 s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u32 mask) 3181 { 3182 u32 gssr = 0; 3183 u32 swmask = mask; 3184 u32 fwmask = mask << 5; 3185 u32 timeout = 200; 3186 u32 i; 3187 3188 DEBUGFUNC("ixgbe_acquire_swfw_sync"); 3189 3190 for (i = 0; i < timeout; i++) { 3191 /* 3192 * SW NVM semaphore bit is used for access to all 3193 * SW_FW_SYNC bits (not just NVM) 3194 */ 3195 if (ixgbe_get_eeprom_semaphore(hw)) 3196 return IXGBE_ERR_SWFW_SYNC; 3197 3198 gssr = IXGBE_READ_REG(hw, IXGBE_GSSR); 3199 if (!(gssr & (fwmask | swmask))) { 3200 gssr |= swmask; 3201 IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr); 3202 ixgbe_release_eeprom_semaphore(hw); 3203 return IXGBE_SUCCESS; 3204 } else { 3205 /* Resource is currently in use by FW or SW */ 3206 ixgbe_release_eeprom_semaphore(hw); 3207 msec_delay(5); 3208 } 3209 } 3210 3211 /* If time expired clear the bits holding the lock and retry */ 3212 if (gssr & (fwmask | swmask)) 3213 ixgbe_release_swfw_sync(hw, gssr & (fwmask | swmask)); 3214 3215 msec_delay(5); 3216 return IXGBE_ERR_SWFW_SYNC; 3217 } 3218 3219 /** 3220 * ixgbe_release_swfw_sync - Release SWFW semaphore 3221 * @hw: pointer to hardware structure 3222 * @mask: Mask to specify which semaphore to release 3223 * 3224 * Releases the SWFW semaphore through the GSSR register for the specified 3225 * function (CSR, PHY0, PHY1, EEPROM, Flash) 3226 **/ 3227 void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u32 mask) 3228 { 3229 u32 gssr; 3230 u32 swmask = mask; 3231 3232 DEBUGFUNC("ixgbe_release_swfw_sync"); 3233 3234 ixgbe_get_eeprom_semaphore(hw); 3235 3236 gssr = IXGBE_READ_REG(hw, IXGBE_GSSR); 3237 gssr &= ~swmask; 3238 IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr); 3239 3240 ixgbe_release_eeprom_semaphore(hw); 3241 } 3242 3243 /** 3244 * ixgbe_disable_sec_rx_path_generic - Stops the receive data path 3245 * @hw: pointer to hardware structure 3246 * 3247 * Stops the receive data path and waits for the HW to internally empty 3248 * the Rx security block 3249 **/ 3250 s32 ixgbe_disable_sec_rx_path_generic(struct ixgbe_hw *hw) 3251 { 3252 #define IXGBE_MAX_SECRX_POLL 40 3253 3254 int i; 3255 int secrxreg; 3256 3257 DEBUGFUNC("ixgbe_disable_sec_rx_path_generic"); 3258 3259 3260 secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL); 3261 secrxreg |= IXGBE_SECRXCTRL_RX_DIS; 3262 IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg); 3263 for (i = 0; i < IXGBE_MAX_SECRX_POLL; i++) { 3264 secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXSTAT); 3265 if (secrxreg & IXGBE_SECRXSTAT_SECRX_RDY) 3266 break; 3267 else 3268 /* Use interrupt-safe sleep just in case */ 3269 usec_delay(1000); 3270 } 3271 3272 /* For informational purposes only */ 3273 if (i >= IXGBE_MAX_SECRX_POLL) 3274 DEBUGOUT("Rx unit being enabled before security " 3275 "path fully disabled. Continuing with init.\n"); 3276 3277 return IXGBE_SUCCESS; 3278 } 3279 3280 /** 3281 * prot_autoc_read_generic - Hides MAC differences needed for AUTOC read 3282 * @hw: pointer to hardware structure 3283 * @reg_val: Value we read from AUTOC 3284 * 3285 * The default case requires no protection so just to the register read. 3286 */ 3287 s32 prot_autoc_read_generic(struct ixgbe_hw *hw, bool *locked, u32 *reg_val) 3288 { 3289 *locked = FALSE; 3290 *reg_val = IXGBE_READ_REG(hw, IXGBE_AUTOC); 3291 return IXGBE_SUCCESS; 3292 } 3293 3294 /** 3295 * prot_autoc_write_generic - Hides MAC differences needed for AUTOC write 3296 * @hw: pointer to hardware structure 3297 * @reg_val: value to write to AUTOC 3298 * @locked: bool to indicate whether the SW/FW lock was already taken by 3299 * previous read. 3300 * 3301 * The default case requires no protection so just to the register write. 3302 */ 3303 s32 prot_autoc_write_generic(struct ixgbe_hw *hw, u32 reg_val, bool locked) 3304 { 3305 UNREFERENCED_1PARAMETER(locked); 3306 3307 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_val); 3308 return IXGBE_SUCCESS; 3309 } 3310 3311 /** 3312 * ixgbe_enable_sec_rx_path_generic - Enables the receive data path 3313 * @hw: pointer to hardware structure 3314 * 3315 * Enables the receive data path. 3316 **/ 3317 s32 ixgbe_enable_sec_rx_path_generic(struct ixgbe_hw *hw) 3318 { 3319 int secrxreg; 3320 3321 DEBUGFUNC("ixgbe_enable_sec_rx_path_generic"); 3322 3323 secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL); 3324 secrxreg &= ~IXGBE_SECRXCTRL_RX_DIS; 3325 IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg); 3326 IXGBE_WRITE_FLUSH(hw); 3327 3328 return IXGBE_SUCCESS; 3329 } 3330 3331 /** 3332 * ixgbe_enable_rx_dma_generic - Enable the Rx DMA unit 3333 * @hw: pointer to hardware structure 3334 * @regval: register value to write to RXCTRL 3335 * 3336 * Enables the Rx DMA unit 3337 **/ 3338 s32 ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval) 3339 { 3340 DEBUGFUNC("ixgbe_enable_rx_dma_generic"); 3341 3342 if (regval & IXGBE_RXCTRL_RXEN) 3343 ixgbe_enable_rx(hw); 3344 else 3345 ixgbe_disable_rx(hw); 3346 3347 return IXGBE_SUCCESS; 3348 } 3349 3350 /** 3351 * ixgbe_blink_led_start_generic - Blink LED based on index. 3352 * @hw: pointer to hardware structure 3353 * @index: led number to blink 3354 **/ 3355 s32 ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index) 3356 { 3357 ixgbe_link_speed speed = 0; 3358 bool link_up = 0; 3359 u32 autoc_reg = 0; 3360 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); 3361 s32 ret_val = IXGBE_SUCCESS; 3362 bool locked = FALSE; 3363 3364 DEBUGFUNC("ixgbe_blink_led_start_generic"); 3365 3366 /* 3367 * Link must be up to auto-blink the LEDs; 3368 * Force it if link is down. 3369 */ 3370 hw->mac.ops.check_link(hw, &speed, &link_up, FALSE); 3371 3372 if (!link_up) { 3373 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg); 3374 if (ret_val != IXGBE_SUCCESS) 3375 goto out; 3376 3377 autoc_reg |= IXGBE_AUTOC_AN_RESTART; 3378 autoc_reg |= IXGBE_AUTOC_FLU; 3379 3380 ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked); 3381 if (ret_val != IXGBE_SUCCESS) 3382 goto out; 3383 3384 IXGBE_WRITE_FLUSH(hw); 3385 msec_delay(10); 3386 } 3387 3388 led_reg &= ~IXGBE_LED_MODE_MASK(index); 3389 led_reg |= IXGBE_LED_BLINK(index); 3390 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); 3391 IXGBE_WRITE_FLUSH(hw); 3392 3393 out: 3394 return ret_val; 3395 } 3396 3397 /** 3398 * ixgbe_blink_led_stop_generic - Stop blinking LED based on index. 3399 * @hw: pointer to hardware structure 3400 * @index: led number to stop blinking 3401 **/ 3402 s32 ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index) 3403 { 3404 u32 autoc_reg = 0; 3405 u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL); 3406 s32 ret_val = IXGBE_SUCCESS; 3407 bool locked = FALSE; 3408 3409 DEBUGFUNC("ixgbe_blink_led_stop_generic"); 3410 3411 ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg); 3412 if (ret_val != IXGBE_SUCCESS) 3413 goto out; 3414 3415 autoc_reg &= ~IXGBE_AUTOC_FLU; 3416 autoc_reg |= IXGBE_AUTOC_AN_RESTART; 3417 3418 ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked); 3419 if (ret_val != IXGBE_SUCCESS) 3420 goto out; 3421 3422 led_reg &= ~IXGBE_LED_MODE_MASK(index); 3423 led_reg &= ~IXGBE_LED_BLINK(index); 3424 led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index); 3425 IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg); 3426 IXGBE_WRITE_FLUSH(hw); 3427 3428 out: 3429 return ret_val; 3430 } 3431 3432 /** 3433 * ixgbe_get_san_mac_addr_offset - Get SAN MAC address offset from the EEPROM 3434 * @hw: pointer to hardware structure 3435 * @san_mac_offset: SAN MAC address offset 3436 * 3437 * This function will read the EEPROM location for the SAN MAC address 3438 * pointer, and returns the value at that location. This is used in both 3439 * get and set mac_addr routines. 3440 **/ 3441 static s32 ixgbe_get_san_mac_addr_offset(struct ixgbe_hw *hw, 3442 u16 *san_mac_offset) 3443 { 3444 s32 ret_val; 3445 3446 DEBUGFUNC("ixgbe_get_san_mac_addr_offset"); 3447 3448 /* 3449 * First read the EEPROM pointer to see if the MAC addresses are 3450 * available. 3451 */ 3452 ret_val = hw->eeprom.ops.read(hw, IXGBE_SAN_MAC_ADDR_PTR, 3453 san_mac_offset); 3454 if (ret_val) { 3455 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 3456 "eeprom at offset %d failed", 3457 IXGBE_SAN_MAC_ADDR_PTR); 3458 } 3459 3460 return ret_val; 3461 } 3462 3463 /** 3464 * ixgbe_get_san_mac_addr_generic - SAN MAC address retrieval from the EEPROM 3465 * @hw: pointer to hardware structure 3466 * @san_mac_addr: SAN MAC address 3467 * 3468 * Reads the SAN MAC address from the EEPROM, if it's available. This is 3469 * per-port, so set_lan_id() must be called before reading the addresses. 3470 * set_lan_id() is called by identify_sfp(), but this cannot be relied 3471 * upon for non-SFP connections, so we must call it here. 3472 **/ 3473 s32 ixgbe_get_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr) 3474 { 3475 u16 san_mac_data, san_mac_offset; 3476 u8 i; 3477 s32 ret_val; 3478 3479 DEBUGFUNC("ixgbe_get_san_mac_addr_generic"); 3480 3481 /* 3482 * First read the EEPROM pointer to see if the MAC addresses are 3483 * available. If they're not, no point in calling set_lan_id() here. 3484 */ 3485 ret_val = ixgbe_get_san_mac_addr_offset(hw, &san_mac_offset); 3486 if (ret_val || san_mac_offset == 0 || san_mac_offset == 0xFFFF) 3487 goto san_mac_addr_out; 3488 3489 /* make sure we know which port we need to program */ 3490 hw->mac.ops.set_lan_id(hw); 3491 /* apply the port offset to the address offset */ 3492 (hw->bus.func) ? (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT1_OFFSET) : 3493 (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT0_OFFSET); 3494 for (i = 0; i < 3; i++) { 3495 ret_val = hw->eeprom.ops.read(hw, san_mac_offset, 3496 &san_mac_data); 3497 if (ret_val) { 3498 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 3499 "eeprom read at offset %d failed", 3500 san_mac_offset); 3501 goto san_mac_addr_out; 3502 } 3503 san_mac_addr[i * 2] = (u8)(san_mac_data); 3504 san_mac_addr[i * 2 + 1] = (u8)(san_mac_data >> 8); 3505 san_mac_offset++; 3506 } 3507 return IXGBE_SUCCESS; 3508 3509 san_mac_addr_out: 3510 /* 3511 * No addresses available in this EEPROM. It's not an 3512 * error though, so just wipe the local address and return. 3513 */ 3514 for (i = 0; i < 6; i++) 3515 san_mac_addr[i] = 0xFF; 3516 return IXGBE_SUCCESS; 3517 } 3518 3519 /** 3520 * ixgbe_set_san_mac_addr_generic - Write the SAN MAC address to the EEPROM 3521 * @hw: pointer to hardware structure 3522 * @san_mac_addr: SAN MAC address 3523 * 3524 * Write a SAN MAC address to the EEPROM. 3525 **/ 3526 s32 ixgbe_set_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr) 3527 { 3528 s32 ret_val; 3529 u16 san_mac_data, san_mac_offset; 3530 u8 i; 3531 3532 DEBUGFUNC("ixgbe_set_san_mac_addr_generic"); 3533 3534 /* Look for SAN mac address pointer. If not defined, return */ 3535 ret_val = ixgbe_get_san_mac_addr_offset(hw, &san_mac_offset); 3536 if (ret_val || san_mac_offset == 0 || san_mac_offset == 0xFFFF) 3537 return IXGBE_ERR_NO_SAN_ADDR_PTR; 3538 3539 /* Make sure we know which port we need to write */ 3540 hw->mac.ops.set_lan_id(hw); 3541 /* Apply the port offset to the address offset */ 3542 (hw->bus.func) ? (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT1_OFFSET) : 3543 (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT0_OFFSET); 3544 3545 for (i = 0; i < 3; i++) { 3546 san_mac_data = (u16)((u16)(san_mac_addr[i * 2 + 1]) << 8); 3547 san_mac_data |= (u16)(san_mac_addr[i * 2]); 3548 hw->eeprom.ops.write(hw, san_mac_offset, san_mac_data); 3549 san_mac_offset++; 3550 } 3551 3552 return IXGBE_SUCCESS; 3553 } 3554 3555 /** 3556 * ixgbe_get_pcie_msix_count_generic - Gets MSI-X vector count 3557 * @hw: pointer to hardware structure 3558 * 3559 * Read PCIe configuration space, and get the MSI-X vector count from 3560 * the capabilities table. 3561 **/ 3562 u16 ixgbe_get_pcie_msix_count_generic(struct ixgbe_hw *hw) 3563 { 3564 u16 msix_count = 1; 3565 u16 max_msix_count; 3566 u16 pcie_offset; 3567 3568 switch (hw->mac.type) { 3569 case ixgbe_mac_82598EB: 3570 pcie_offset = IXGBE_PCIE_MSIX_82598_CAPS; 3571 max_msix_count = IXGBE_MAX_MSIX_VECTORS_82598; 3572 break; 3573 case ixgbe_mac_82599EB: 3574 case ixgbe_mac_X540: 3575 case ixgbe_mac_X550: 3576 case ixgbe_mac_X550EM_x: 3577 case ixgbe_mac_X550EM_a: 3578 pcie_offset = IXGBE_PCIE_MSIX_82599_CAPS; 3579 max_msix_count = IXGBE_MAX_MSIX_VECTORS_82599; 3580 break; 3581 default: 3582 return msix_count; 3583 } 3584 3585 DEBUGFUNC("ixgbe_get_pcie_msix_count_generic"); 3586 msix_count = IXGBE_READ_PCIE_WORD(hw, pcie_offset); 3587 if (IXGBE_REMOVED(hw->hw_addr)) 3588 msix_count = 0; 3589 msix_count &= IXGBE_PCIE_MSIX_TBL_SZ_MASK; 3590 3591 /* MSI-X count is zero-based in HW */ 3592 msix_count++; 3593 3594 if (msix_count > max_msix_count) 3595 msix_count = max_msix_count; 3596 3597 return msix_count; 3598 } 3599 3600 /** 3601 * ixgbe_insert_mac_addr_generic - Find a RAR for this mac address 3602 * @hw: pointer to hardware structure 3603 * @addr: Address to put into receive address register 3604 * @vmdq: VMDq pool to assign 3605 * 3606 * Puts an ethernet address into a receive address register, or 3607 * finds the rar that it is aleady in; adds to the pool list 3608 **/ 3609 s32 ixgbe_insert_mac_addr_generic(struct ixgbe_hw *hw, u8 *addr, u32 vmdq) 3610 { 3611 static const u32 NO_EMPTY_RAR_FOUND = 0xFFFFFFFF; 3612 u32 first_empty_rar = NO_EMPTY_RAR_FOUND; 3613 u32 rar; 3614 u32 rar_low, rar_high; 3615 u32 addr_low, addr_high; 3616 3617 DEBUGFUNC("ixgbe_insert_mac_addr_generic"); 3618 3619 /* swap bytes for HW little endian */ 3620 addr_low = addr[0] | (addr[1] << 8) 3621 | (addr[2] << 16) 3622 | (addr[3] << 24); 3623 addr_high = addr[4] | (addr[5] << 8); 3624 3625 /* 3626 * Either find the mac_id in rar or find the first empty space. 3627 * rar_highwater points to just after the highest currently used 3628 * rar in order to shorten the search. It grows when we add a new 3629 * rar to the top. 3630 */ 3631 for (rar = 0; rar < hw->mac.rar_highwater; rar++) { 3632 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar)); 3633 3634 if (((IXGBE_RAH_AV & rar_high) == 0) 3635 && first_empty_rar == NO_EMPTY_RAR_FOUND) { 3636 first_empty_rar = rar; 3637 } else if ((rar_high & 0xFFFF) == addr_high) { 3638 rar_low = IXGBE_READ_REG(hw, IXGBE_RAL(rar)); 3639 if (rar_low == addr_low) 3640 break; /* found it already in the rars */ 3641 } 3642 } 3643 3644 if (rar < hw->mac.rar_highwater) { 3645 /* already there so just add to the pool bits */ 3646 ixgbe_set_vmdq(hw, rar, vmdq); 3647 } else if (first_empty_rar != NO_EMPTY_RAR_FOUND) { 3648 /* stick it into first empty RAR slot we found */ 3649 rar = first_empty_rar; 3650 ixgbe_set_rar(hw, rar, addr, vmdq, IXGBE_RAH_AV); 3651 } else if (rar == hw->mac.rar_highwater) { 3652 /* add it to the top of the list and inc the highwater mark */ 3653 ixgbe_set_rar(hw, rar, addr, vmdq, IXGBE_RAH_AV); 3654 hw->mac.rar_highwater++; 3655 } else if (rar >= hw->mac.num_rar_entries) { 3656 return IXGBE_ERR_INVALID_MAC_ADDR; 3657 } 3658 3659 /* 3660 * If we found rar[0], make sure the default pool bit (we use pool 0) 3661 * remains cleared to be sure default pool packets will get delivered 3662 */ 3663 if (rar == 0) 3664 ixgbe_clear_vmdq(hw, rar, 0); 3665 3666 return rar; 3667 } 3668 3669 /** 3670 * ixgbe_clear_vmdq_generic - Disassociate a VMDq pool index from a rx address 3671 * @hw: pointer to hardware struct 3672 * @rar: receive address register index to disassociate 3673 * @vmdq: VMDq pool index to remove from the rar 3674 **/ 3675 s32 ixgbe_clear_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq) 3676 { 3677 u32 mpsar_lo, mpsar_hi; 3678 u32 rar_entries = hw->mac.num_rar_entries; 3679 3680 DEBUGFUNC("ixgbe_clear_vmdq_generic"); 3681 3682 /* Make sure we are using a valid rar index range */ 3683 if (rar >= rar_entries) { 3684 ERROR_REPORT2(IXGBE_ERROR_ARGUMENT, 3685 "RAR index %d is out of range.\n", rar); 3686 return IXGBE_ERR_INVALID_ARGUMENT; 3687 } 3688 3689 mpsar_lo = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar)); 3690 mpsar_hi = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar)); 3691 3692 if (IXGBE_REMOVED(hw->hw_addr)) 3693 goto done; 3694 3695 if (!mpsar_lo && !mpsar_hi) 3696 goto done; 3697 3698 if (vmdq == IXGBE_CLEAR_VMDQ_ALL) { 3699 if (mpsar_lo) { 3700 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0); 3701 mpsar_lo = 0; 3702 } 3703 if (mpsar_hi) { 3704 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0); 3705 mpsar_hi = 0; 3706 } 3707 } else if (vmdq < 32) { 3708 mpsar_lo &= ~(1 << vmdq); 3709 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar_lo); 3710 } else { 3711 mpsar_hi &= ~(1 << (vmdq - 32)); 3712 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar_hi); 3713 } 3714 3715 /* was that the last pool using this rar? */ 3716 if (mpsar_lo == 0 && mpsar_hi == 0 && rar != 0) 3717 hw->mac.ops.clear_rar(hw, rar); 3718 done: 3719 return IXGBE_SUCCESS; 3720 } 3721 3722 /** 3723 * ixgbe_set_vmdq_generic - Associate a VMDq pool index with a rx address 3724 * @hw: pointer to hardware struct 3725 * @rar: receive address register index to associate with a VMDq index 3726 * @vmdq: VMDq pool index 3727 **/ 3728 s32 ixgbe_set_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq) 3729 { 3730 u32 mpsar; 3731 u32 rar_entries = hw->mac.num_rar_entries; 3732 3733 DEBUGFUNC("ixgbe_set_vmdq_generic"); 3734 3735 /* Make sure we are using a valid rar index range */ 3736 if (rar >= rar_entries) { 3737 ERROR_REPORT2(IXGBE_ERROR_ARGUMENT, 3738 "RAR index %d is out of range.\n", rar); 3739 return IXGBE_ERR_INVALID_ARGUMENT; 3740 } 3741 3742 if (vmdq < 32) { 3743 mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar)); 3744 mpsar |= 1 << vmdq; 3745 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar); 3746 } else { 3747 mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar)); 3748 mpsar |= 1 << (vmdq - 32); 3749 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar); 3750 } 3751 return IXGBE_SUCCESS; 3752 } 3753 3754 /** 3755 * This function should only be involved in the IOV mode. 3756 * In IOV mode, Default pool is next pool after the number of 3757 * VFs advertized and not 0. 3758 * MPSAR table needs to be updated for SAN_MAC RAR [hw->mac.san_mac_rar_index] 3759 * 3760 * ixgbe_set_vmdq_san_mac - Associate default VMDq pool index with a rx address 3761 * @hw: pointer to hardware struct 3762 * @vmdq: VMDq pool index 3763 **/ 3764 s32 ixgbe_set_vmdq_san_mac_generic(struct ixgbe_hw *hw, u32 vmdq) 3765 { 3766 u32 rar = hw->mac.san_mac_rar_index; 3767 3768 DEBUGFUNC("ixgbe_set_vmdq_san_mac"); 3769 3770 if (vmdq < 32) { 3771 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 1 << vmdq); 3772 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0); 3773 } else { 3774 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0); 3775 IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 1 << (vmdq - 32)); 3776 } 3777 3778 return IXGBE_SUCCESS; 3779 } 3780 3781 /** 3782 * ixgbe_init_uta_tables_generic - Initialize the Unicast Table Array 3783 * @hw: pointer to hardware structure 3784 **/ 3785 s32 ixgbe_init_uta_tables_generic(struct ixgbe_hw *hw) 3786 { 3787 int i; 3788 3789 DEBUGFUNC("ixgbe_init_uta_tables_generic"); 3790 DEBUGOUT(" Clearing UTA\n"); 3791 3792 for (i = 0; i < 128; i++) 3793 IXGBE_WRITE_REG(hw, IXGBE_UTA(i), 0); 3794 3795 return IXGBE_SUCCESS; 3796 } 3797 3798 /** 3799 * ixgbe_find_vlvf_slot - find the vlanid or the first empty slot 3800 * @hw: pointer to hardware structure 3801 * @vlan: VLAN id to write to VLAN filter 3802 * 3803 * return the VLVF index where this VLAN id should be placed 3804 * 3805 **/ 3806 s32 ixgbe_find_vlvf_slot(struct ixgbe_hw *hw, u32 vlan) 3807 { 3808 u32 bits = 0; 3809 u32 first_empty_slot = 0; 3810 s32 regindex; 3811 3812 /* short cut the special case */ 3813 if (vlan == 0) 3814 return 0; 3815 3816 /* 3817 * Search for the vlan id in the VLVF entries. Save off the first empty 3818 * slot found along the way 3819 */ 3820 for (regindex = 1; regindex < IXGBE_VLVF_ENTRIES; regindex++) { 3821 bits = IXGBE_READ_REG(hw, IXGBE_VLVF(regindex)); 3822 if (!bits && !(first_empty_slot)) 3823 first_empty_slot = regindex; 3824 else if ((bits & 0x0FFF) == vlan) 3825 break; 3826 } 3827 3828 /* 3829 * If regindex is less than IXGBE_VLVF_ENTRIES, then we found the vlan 3830 * in the VLVF. Else use the first empty VLVF register for this 3831 * vlan id. 3832 */ 3833 if (regindex >= IXGBE_VLVF_ENTRIES) { 3834 if (first_empty_slot) 3835 regindex = first_empty_slot; 3836 else { 3837 ERROR_REPORT1(IXGBE_ERROR_SOFTWARE, 3838 "No space in VLVF.\n"); 3839 regindex = IXGBE_ERR_NO_SPACE; 3840 } 3841 } 3842 3843 return regindex; 3844 } 3845 3846 /** 3847 * ixgbe_set_vfta_generic - Set VLAN filter table 3848 * @hw: pointer to hardware structure 3849 * @vlan: VLAN id to write to VLAN filter 3850 * @vind: VMDq output index that maps queue to VLAN id in VFVFB 3851 * @vlan_on: boolean flag to turn on/off VLAN in VFVF 3852 * 3853 * Turn on/off specified VLAN in the VLAN filter table. 3854 **/ 3855 s32 ixgbe_set_vfta_generic(struct ixgbe_hw *hw, u32 vlan, u32 vind, 3856 bool vlan_on) 3857 { 3858 s32 regindex; 3859 u32 bitindex; 3860 u32 vfta; 3861 u32 targetbit; 3862 s32 ret_val = IXGBE_SUCCESS; 3863 bool vfta_changed = FALSE; 3864 3865 DEBUGFUNC("ixgbe_set_vfta_generic"); 3866 3867 if (vlan > 4095) 3868 return IXGBE_ERR_PARAM; 3869 3870 /* 3871 * this is a 2 part operation - first the VFTA, then the 3872 * VLVF and VLVFB if VT Mode is set 3873 * We don't write the VFTA until we know the VLVF part succeeded. 3874 */ 3875 3876 /* Part 1 3877 * The VFTA is a bitstring made up of 128 32-bit registers 3878 * that enable the particular VLAN id, much like the MTA: 3879 * bits[11-5]: which register 3880 * bits[4-0]: which bit in the register 3881 */ 3882 regindex = (vlan >> 5) & 0x7F; 3883 bitindex = vlan & 0x1F; 3884 targetbit = (1 << bitindex); 3885 vfta = IXGBE_READ_REG(hw, IXGBE_VFTA(regindex)); 3886 3887 if (vlan_on) { 3888 if (!(vfta & targetbit)) { 3889 vfta |= targetbit; 3890 vfta_changed = TRUE; 3891 } 3892 } else { 3893 if ((vfta & targetbit)) { 3894 vfta &= ~targetbit; 3895 vfta_changed = TRUE; 3896 } 3897 } 3898 3899 /* Part 2 3900 * Call ixgbe_set_vlvf_generic to set VLVFB and VLVF 3901 */ 3902 ret_val = ixgbe_set_vlvf_generic(hw, vlan, vind, vlan_on, 3903 &vfta_changed); 3904 if (ret_val != IXGBE_SUCCESS) 3905 return ret_val; 3906 3907 if (vfta_changed) 3908 IXGBE_WRITE_REG(hw, IXGBE_VFTA(regindex), vfta); 3909 3910 return IXGBE_SUCCESS; 3911 } 3912 3913 /** 3914 * ixgbe_set_vlvf_generic - Set VLAN Pool Filter 3915 * @hw: pointer to hardware structure 3916 * @vlan: VLAN id to write to VLAN filter 3917 * @vind: VMDq output index that maps queue to VLAN id in VFVFB 3918 * @vlan_on: boolean flag to turn on/off VLAN in VFVF 3919 * @vfta_changed: pointer to boolean flag which indicates whether VFTA 3920 * should be changed 3921 * 3922 * Turn on/off specified bit in VLVF table. 3923 **/ 3924 s32 ixgbe_set_vlvf_generic(struct ixgbe_hw *hw, u32 vlan, u32 vind, 3925 bool vlan_on, bool *vfta_changed) 3926 { 3927 u32 vt; 3928 3929 DEBUGFUNC("ixgbe_set_vlvf_generic"); 3930 3931 if (vlan > 4095) 3932 return IXGBE_ERR_PARAM; 3933 3934 /* If VT Mode is set 3935 * Either vlan_on 3936 * make sure the vlan is in VLVF 3937 * set the vind bit in the matching VLVFB 3938 * Or !vlan_on 3939 * clear the pool bit and possibly the vind 3940 */ 3941 vt = IXGBE_READ_REG(hw, IXGBE_VT_CTL); 3942 if (vt & IXGBE_VT_CTL_VT_ENABLE) { 3943 s32 vlvf_index; 3944 u32 bits; 3945 3946 vlvf_index = ixgbe_find_vlvf_slot(hw, vlan); 3947 if (vlvf_index < 0) 3948 return vlvf_index; 3949 3950 if (vlan_on) { 3951 /* set the pool bit */ 3952 if (vind < 32) { 3953 bits = IXGBE_READ_REG(hw, 3954 IXGBE_VLVFB(vlvf_index * 2)); 3955 bits |= (1 << vind); 3956 IXGBE_WRITE_REG(hw, 3957 IXGBE_VLVFB(vlvf_index * 2), 3958 bits); 3959 } else { 3960 bits = IXGBE_READ_REG(hw, 3961 IXGBE_VLVFB((vlvf_index * 2) + 1)); 3962 bits |= (1 << (vind - 32)); 3963 IXGBE_WRITE_REG(hw, 3964 IXGBE_VLVFB((vlvf_index * 2) + 1), 3965 bits); 3966 } 3967 } else { 3968 /* clear the pool bit */ 3969 if (vind < 32) { 3970 bits = IXGBE_READ_REG(hw, 3971 IXGBE_VLVFB(vlvf_index * 2)); 3972 bits &= ~(1 << vind); 3973 IXGBE_WRITE_REG(hw, 3974 IXGBE_VLVFB(vlvf_index * 2), 3975 bits); 3976 bits |= IXGBE_READ_REG(hw, 3977 IXGBE_VLVFB((vlvf_index * 2) + 1)); 3978 } else { 3979 bits = IXGBE_READ_REG(hw, 3980 IXGBE_VLVFB((vlvf_index * 2) + 1)); 3981 bits &= ~(1 << (vind - 32)); 3982 IXGBE_WRITE_REG(hw, 3983 IXGBE_VLVFB((vlvf_index * 2) + 1), 3984 bits); 3985 bits |= IXGBE_READ_REG(hw, 3986 IXGBE_VLVFB(vlvf_index * 2)); 3987 } 3988 } 3989 3990 /* 3991 * If there are still bits set in the VLVFB registers 3992 * for the VLAN ID indicated we need to see if the 3993 * caller is requesting that we clear the VFTA entry bit. 3994 * If the caller has requested that we clear the VFTA 3995 * entry bit but there are still pools/VFs using this VLAN 3996 * ID entry then ignore the request. We're not worried 3997 * about the case where we're turning the VFTA VLAN ID 3998 * entry bit on, only when requested to turn it off as 3999 * there may be multiple pools and/or VFs using the 4000 * VLAN ID entry. In that case we cannot clear the 4001 * VFTA bit until all pools/VFs using that VLAN ID have also 4002 * been cleared. This will be indicated by "bits" being 4003 * zero. 4004 */ 4005 if (bits) { 4006 IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), 4007 (IXGBE_VLVF_VIEN | vlan)); 4008 if ((!vlan_on) && (vfta_changed != NULL)) { 4009 /* someone wants to clear the vfta entry 4010 * but some pools/VFs are still using it. 4011 * Ignore it. */ 4012 *vfta_changed = FALSE; 4013 } 4014 } else 4015 IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), 0); 4016 } 4017 4018 return IXGBE_SUCCESS; 4019 } 4020 4021 /** 4022 * ixgbe_clear_vfta_generic - Clear VLAN filter table 4023 * @hw: pointer to hardware structure 4024 * 4025 * Clears the VLAN filer table, and the VMDq index associated with the filter 4026 **/ 4027 s32 ixgbe_clear_vfta_generic(struct ixgbe_hw *hw) 4028 { 4029 u32 offset; 4030 4031 DEBUGFUNC("ixgbe_clear_vfta_generic"); 4032 4033 for (offset = 0; offset < hw->mac.vft_size; offset++) 4034 IXGBE_WRITE_REG(hw, IXGBE_VFTA(offset), 0); 4035 4036 for (offset = 0; offset < IXGBE_VLVF_ENTRIES; offset++) { 4037 IXGBE_WRITE_REG(hw, IXGBE_VLVF(offset), 0); 4038 IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2), 0); 4039 IXGBE_WRITE_REG(hw, IXGBE_VLVFB((offset * 2) + 1), 0); 4040 } 4041 4042 return IXGBE_SUCCESS; 4043 } 4044 4045 /** 4046 * ixgbe_check_mac_link_generic - Determine link and speed status 4047 * @hw: pointer to hardware structure 4048 * @speed: pointer to link speed 4049 * @link_up: TRUE when link is up 4050 * @link_up_wait_to_complete: bool used to wait for link up or not 4051 * 4052 * Reads the links register to determine if link is up and the current speed 4053 **/ 4054 s32 ixgbe_check_mac_link_generic(struct ixgbe_hw *hw, ixgbe_link_speed *speed, 4055 bool *link_up, bool link_up_wait_to_complete) 4056 { 4057 u32 links_reg, links_orig; 4058 u32 i; 4059 4060 DEBUGFUNC("ixgbe_check_mac_link_generic"); 4061 4062 /* clear the old state */ 4063 links_orig = IXGBE_READ_REG(hw, IXGBE_LINKS); 4064 4065 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); 4066 4067 if (links_orig != links_reg) { 4068 DEBUGOUT2("LINKS changed from %08X to %08X\n", 4069 links_orig, links_reg); 4070 } 4071 4072 if (link_up_wait_to_complete) { 4073 for (i = 0; i < IXGBE_LINK_UP_TIME; i++) { 4074 if (links_reg & IXGBE_LINKS_UP) { 4075 *link_up = TRUE; 4076 break; 4077 } else { 4078 *link_up = FALSE; 4079 } 4080 msec_delay(100); 4081 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); 4082 } 4083 } else { 4084 if (links_reg & IXGBE_LINKS_UP) 4085 *link_up = TRUE; 4086 else 4087 *link_up = FALSE; 4088 } 4089 4090 switch (links_reg & IXGBE_LINKS_SPEED_82599) { 4091 case IXGBE_LINKS_SPEED_10G_82599: 4092 *speed = IXGBE_LINK_SPEED_10GB_FULL; 4093 if (hw->mac.type >= ixgbe_mac_X550) { 4094 if (links_reg & IXGBE_LINKS_SPEED_NON_STD) 4095 *speed = IXGBE_LINK_SPEED_2_5GB_FULL; 4096 } 4097 break; 4098 case IXGBE_LINKS_SPEED_1G_82599: 4099 *speed = IXGBE_LINK_SPEED_1GB_FULL; 4100 break; 4101 case IXGBE_LINKS_SPEED_100_82599: 4102 *speed = IXGBE_LINK_SPEED_100_FULL; 4103 if (hw->mac.type >= ixgbe_mac_X550) { 4104 if (links_reg & IXGBE_LINKS_SPEED_NON_STD) 4105 *speed = IXGBE_LINK_SPEED_5GB_FULL; 4106 } 4107 break; 4108 default: 4109 *speed = IXGBE_LINK_SPEED_UNKNOWN; 4110 } 4111 4112 return IXGBE_SUCCESS; 4113 } 4114 4115 /** 4116 * ixgbe_get_wwn_prefix_generic - Get alternative WWNN/WWPN prefix from 4117 * the EEPROM 4118 * @hw: pointer to hardware structure 4119 * @wwnn_prefix: the alternative WWNN prefix 4120 * @wwpn_prefix: the alternative WWPN prefix 4121 * 4122 * This function will read the EEPROM from the alternative SAN MAC address 4123 * block to check the support for the alternative WWNN/WWPN prefix support. 4124 **/ 4125 s32 ixgbe_get_wwn_prefix_generic(struct ixgbe_hw *hw, u16 *wwnn_prefix, 4126 u16 *wwpn_prefix) 4127 { 4128 u16 offset, caps; 4129 u16 alt_san_mac_blk_offset; 4130 4131 DEBUGFUNC("ixgbe_get_wwn_prefix_generic"); 4132 4133 /* clear output first */ 4134 *wwnn_prefix = 0xFFFF; 4135 *wwpn_prefix = 0xFFFF; 4136 4137 /* check if alternative SAN MAC is supported */ 4138 offset = IXGBE_ALT_SAN_MAC_ADDR_BLK_PTR; 4139 if (hw->eeprom.ops.read(hw, offset, &alt_san_mac_blk_offset)) 4140 goto wwn_prefix_err; 4141 4142 if ((alt_san_mac_blk_offset == 0) || 4143 (alt_san_mac_blk_offset == 0xFFFF)) 4144 goto wwn_prefix_out; 4145 4146 /* check capability in alternative san mac address block */ 4147 offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET; 4148 if (hw->eeprom.ops.read(hw, offset, &caps)) 4149 goto wwn_prefix_err; 4150 if (!(caps & IXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN)) 4151 goto wwn_prefix_out; 4152 4153 /* get the corresponding prefix for WWNN/WWPN */ 4154 offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET; 4155 if (hw->eeprom.ops.read(hw, offset, wwnn_prefix)) { 4156 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 4157 "eeprom read at offset %d failed", offset); 4158 } 4159 4160 offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET; 4161 if (hw->eeprom.ops.read(hw, offset, wwpn_prefix)) 4162 goto wwn_prefix_err; 4163 4164 wwn_prefix_out: 4165 return IXGBE_SUCCESS; 4166 4167 wwn_prefix_err: 4168 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 4169 "eeprom read at offset %d failed", offset); 4170 return IXGBE_SUCCESS; 4171 } 4172 4173 /** 4174 * ixgbe_get_fcoe_boot_status_generic - Get FCOE boot status from EEPROM 4175 * @hw: pointer to hardware structure 4176 * @bs: the fcoe boot status 4177 * 4178 * This function will read the FCOE boot status from the iSCSI FCOE block 4179 **/ 4180 s32 ixgbe_get_fcoe_boot_status_generic(struct ixgbe_hw *hw, u16 *bs) 4181 { 4182 u16 offset, caps, flags; 4183 s32 status; 4184 4185 DEBUGFUNC("ixgbe_get_fcoe_boot_status_generic"); 4186 4187 /* clear output first */ 4188 *bs = ixgbe_fcoe_bootstatus_unavailable; 4189 4190 /* check if FCOE IBA block is present */ 4191 offset = IXGBE_FCOE_IBA_CAPS_BLK_PTR; 4192 status = hw->eeprom.ops.read(hw, offset, &caps); 4193 if (status != IXGBE_SUCCESS) 4194 goto out; 4195 4196 if (!(caps & IXGBE_FCOE_IBA_CAPS_FCOE)) 4197 goto out; 4198 4199 /* check if iSCSI FCOE block is populated */ 4200 status = hw->eeprom.ops.read(hw, IXGBE_ISCSI_FCOE_BLK_PTR, &offset); 4201 if (status != IXGBE_SUCCESS) 4202 goto out; 4203 4204 if ((offset == 0) || (offset == 0xFFFF)) 4205 goto out; 4206 4207 /* read fcoe flags in iSCSI FCOE block */ 4208 offset = offset + IXGBE_ISCSI_FCOE_FLAGS_OFFSET; 4209 status = hw->eeprom.ops.read(hw, offset, &flags); 4210 if (status != IXGBE_SUCCESS) 4211 goto out; 4212 4213 if (flags & IXGBE_ISCSI_FCOE_FLAGS_ENABLE) 4214 *bs = ixgbe_fcoe_bootstatus_enabled; 4215 else 4216 *bs = ixgbe_fcoe_bootstatus_disabled; 4217 4218 out: 4219 return status; 4220 } 4221 4222 /** 4223 * ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing 4224 * @hw: pointer to hardware structure 4225 * @enable: enable or disable switch for anti-spoofing 4226 * @pf: Physical Function pool - do not enable anti-spoofing for the PF 4227 * 4228 **/ 4229 void ixgbe_set_mac_anti_spoofing(struct ixgbe_hw *hw, bool enable, int pf) 4230 { 4231 int j; 4232 int pf_target_reg = pf >> 3; 4233 int pf_target_shift = pf % 8; 4234 u32 pfvfspoof = 0; 4235 4236 if (hw->mac.type == ixgbe_mac_82598EB) 4237 return; 4238 4239 if (enable) 4240 pfvfspoof = IXGBE_SPOOF_MACAS_MASK; 4241 4242 /* 4243 * PFVFSPOOF register array is size 8 with 8 bits assigned to 4244 * MAC anti-spoof enables in each register array element. 4245 */ 4246 for (j = 0; j < pf_target_reg; j++) 4247 IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(j), pfvfspoof); 4248 4249 /* 4250 * The PF should be allowed to spoof so that it can support 4251 * emulation mode NICs. Do not set the bits assigned to the PF 4252 */ 4253 pfvfspoof &= (1 << pf_target_shift) - 1; 4254 IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(j), pfvfspoof); 4255 4256 /* 4257 * Remaining pools belong to the PF so they do not need to have 4258 * anti-spoofing enabled. 4259 */ 4260 for (j++; j < IXGBE_PFVFSPOOF_REG_COUNT; j++) 4261 IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(j), 0); 4262 } 4263 4264 /** 4265 * ixgbe_set_vlan_anti_spoofing - Enable/Disable VLAN anti-spoofing 4266 * @hw: pointer to hardware structure 4267 * @enable: enable or disable switch for VLAN anti-spoofing 4268 * @vf: Virtual Function pool - VF Pool to set for VLAN anti-spoofing 4269 * 4270 **/ 4271 void ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf) 4272 { 4273 int vf_target_reg = vf >> 3; 4274 int vf_target_shift = vf % 8 + IXGBE_SPOOF_VLANAS_SHIFT; 4275 u32 pfvfspoof; 4276 4277 if (hw->mac.type == ixgbe_mac_82598EB) 4278 return; 4279 4280 pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg)); 4281 if (enable) 4282 pfvfspoof |= (1 << vf_target_shift); 4283 else 4284 pfvfspoof &= ~(1 << vf_target_shift); 4285 IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof); 4286 } 4287 4288 /** 4289 * ixgbe_get_device_caps_generic - Get additional device capabilities 4290 * @hw: pointer to hardware structure 4291 * @device_caps: the EEPROM word with the extra device capabilities 4292 * 4293 * This function will read the EEPROM location for the device capabilities, 4294 * and return the word through device_caps. 4295 **/ 4296 s32 ixgbe_get_device_caps_generic(struct ixgbe_hw *hw, u16 *device_caps) 4297 { 4298 DEBUGFUNC("ixgbe_get_device_caps_generic"); 4299 4300 hw->eeprom.ops.read(hw, IXGBE_DEVICE_CAPS, device_caps); 4301 4302 return IXGBE_SUCCESS; 4303 } 4304 4305 /** 4306 * ixgbe_enable_relaxed_ordering_gen2 - Enable relaxed ordering 4307 * @hw: pointer to hardware structure 4308 * 4309 **/ 4310 void ixgbe_enable_relaxed_ordering_gen2(struct ixgbe_hw *hw) 4311 { 4312 u32 regval; 4313 u32 i; 4314 4315 DEBUGFUNC("ixgbe_enable_relaxed_ordering_gen2"); 4316 4317 /* Enable relaxed ordering */ 4318 for (i = 0; i < hw->mac.max_tx_queues; i++) { 4319 regval = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL_82599(i)); 4320 regval |= IXGBE_DCA_TXCTRL_DESC_WRO_EN; 4321 IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL_82599(i), regval); 4322 } 4323 4324 for (i = 0; i < hw->mac.max_rx_queues; i++) { 4325 regval = IXGBE_READ_REG(hw, IXGBE_DCA_RXCTRL(i)); 4326 regval |= IXGBE_DCA_RXCTRL_DATA_WRO_EN | 4327 IXGBE_DCA_RXCTRL_HEAD_WRO_EN; 4328 IXGBE_WRITE_REG(hw, IXGBE_DCA_RXCTRL(i), regval); 4329 } 4330 4331 } 4332 4333 /** 4334 * ixgbe_calculate_checksum - Calculate checksum for buffer 4335 * @buffer: pointer to EEPROM 4336 * @length: size of EEPROM to calculate a checksum for 4337 * Calculates the checksum for some buffer on a specified length. The 4338 * checksum calculated is returned. 4339 **/ 4340 u8 ixgbe_calculate_checksum(u8 *buffer, u32 length) 4341 { 4342 u32 i; 4343 u8 sum = 0; 4344 4345 DEBUGFUNC("ixgbe_calculate_checksum"); 4346 4347 if (!buffer) 4348 return 0; 4349 4350 for (i = 0; i < length; i++) 4351 sum += buffer[i]; 4352 4353 return (u8) (0 - sum); 4354 } 4355 4356 /** 4357 * ixgbe_host_interface_command - Issue command to manageability block 4358 * @hw: pointer to the HW structure 4359 * @buffer: contains the command to write and where the return status will 4360 * be placed 4361 * @length: length of buffer, must be multiple of 4 bytes 4362 * @timeout: time in ms to wait for command completion 4363 * @return_data: read and return data from the buffer (TRUE) or not (FALSE) 4364 * Needed because FW structures are big endian and decoding of 4365 * these fields can be 8 bit or 16 bit based on command. Decoding 4366 * is not easily understood without making a table of commands. 4367 * So we will leave this up to the caller to read back the data 4368 * in these cases. 4369 * 4370 * Communicates with the manageability block. On success return IXGBE_SUCCESS 4371 * else return IXGBE_ERR_HOST_INTERFACE_COMMAND. 4372 **/ 4373 s32 ixgbe_host_interface_command(struct ixgbe_hw *hw, u32 *buffer, 4374 u32 length, u32 timeout, bool return_data) 4375 { 4376 u32 hicr, i, bi, fwsts; 4377 u32 hdr_size = sizeof(struct ixgbe_hic_hdr); 4378 u16 buf_len; 4379 u16 dword_len; 4380 4381 DEBUGFUNC("ixgbe_host_interface_command"); 4382 4383 if (length == 0 || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) { 4384 DEBUGOUT1("Buffer length failure buffersize=%d.\n", length); 4385 return IXGBE_ERR_HOST_INTERFACE_COMMAND; 4386 } 4387 /* Set bit 9 of FWSTS clearing FW reset indication */ 4388 fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS); 4389 IXGBE_WRITE_REG(hw, IXGBE_FWSTS, fwsts | IXGBE_FWSTS_FWRI); 4390 4391 /* Check that the host interface is enabled. */ 4392 hicr = IXGBE_READ_REG(hw, IXGBE_HICR); 4393 if ((hicr & IXGBE_HICR_EN) == 0) { 4394 DEBUGOUT("IXGBE_HOST_EN bit disabled.\n"); 4395 return IXGBE_ERR_HOST_INTERFACE_COMMAND; 4396 } 4397 4398 /* Calculate length in DWORDs. We must be DWORD aligned */ 4399 if ((length % (sizeof(u32))) != 0) { 4400 DEBUGOUT("Buffer length failure, not aligned to dword"); 4401 return IXGBE_ERR_INVALID_ARGUMENT; 4402 } 4403 4404 dword_len = length >> 2; 4405 4406 /* The device driver writes the relevant command block 4407 * into the ram area. 4408 */ 4409 for (i = 0; i < dword_len; i++) 4410 IXGBE_WRITE_REG_ARRAY(hw, IXGBE_FLEX_MNG, 4411 i, IXGBE_CPU_TO_LE32(buffer[i])); 4412 4413 /* Setting this bit tells the ARC that a new command is pending. */ 4414 IXGBE_WRITE_REG(hw, IXGBE_HICR, hicr | IXGBE_HICR_C); 4415 4416 for (i = 0; i < timeout; i++) { 4417 hicr = IXGBE_READ_REG(hw, IXGBE_HICR); 4418 if (!(hicr & IXGBE_HICR_C)) 4419 break; 4420 msec_delay(1); 4421 } 4422 4423 /* Check command completion */ 4424 if ((timeout != 0 && i == timeout) || 4425 !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV)) { 4426 ERROR_REPORT1(IXGBE_ERROR_CAUTION, 4427 "Command has failed with no status valid.\n"); 4428 return IXGBE_ERR_HOST_INTERFACE_COMMAND; 4429 } 4430 4431 if (!return_data) 4432 return 0; 4433 4434 /* Calculate length in DWORDs */ 4435 dword_len = hdr_size >> 2; 4436 4437 /* first pull in the header so we know the buffer length */ 4438 for (bi = 0; bi < dword_len; bi++) { 4439 buffer[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi); 4440 IXGBE_LE32_TO_CPUS(&buffer[bi]); 4441 } 4442 4443 /* If there is any thing in data position pull it in */ 4444 buf_len = ((struct ixgbe_hic_hdr *)buffer)->buf_len; 4445 if (buf_len == 0) 4446 return 0; 4447 4448 if (length < buf_len + hdr_size) { 4449 DEBUGOUT("Buffer not large enough for reply message.\n"); 4450 return IXGBE_ERR_HOST_INTERFACE_COMMAND; 4451 } 4452 4453 /* Calculate length in DWORDs, add 3 for odd lengths */ 4454 dword_len = (buf_len + 3) >> 2; 4455 4456 /* Pull in the rest of the buffer (bi is where we left off) */ 4457 for (; bi <= dword_len; bi++) { 4458 buffer[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi); 4459 IXGBE_LE32_TO_CPUS(&buffer[bi]); 4460 } 4461 4462 return 0; 4463 } 4464 4465 /** 4466 * ixgbe_set_fw_drv_ver_generic - Sends driver version to firmware 4467 * @hw: pointer to the HW structure 4468 * @maj: driver version major number 4469 * @min: driver version minor number 4470 * @build: driver version build number 4471 * @sub: driver version sub build number 4472 * 4473 * Sends driver version number to firmware through the manageability 4474 * block. On success return IXGBE_SUCCESS 4475 * else returns IXGBE_ERR_SWFW_SYNC when encountering an error acquiring 4476 * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails. 4477 **/ 4478 s32 ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min, 4479 u8 build, u8 sub) 4480 { 4481 struct ixgbe_hic_drv_info fw_cmd; 4482 int i; 4483 s32 ret_val = IXGBE_SUCCESS; 4484 4485 DEBUGFUNC("ixgbe_set_fw_drv_ver_generic"); 4486 4487 if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM) 4488 != IXGBE_SUCCESS) { 4489 ret_val = IXGBE_ERR_SWFW_SYNC; 4490 goto out; 4491 } 4492 4493 fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO; 4494 fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN; 4495 fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED; 4496 fw_cmd.port_num = (u8)hw->bus.func; 4497 fw_cmd.ver_maj = maj; 4498 fw_cmd.ver_min = min; 4499 fw_cmd.ver_build = build; 4500 fw_cmd.ver_sub = sub; 4501 fw_cmd.hdr.checksum = 0; 4502 fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd, 4503 (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len)); 4504 fw_cmd.pad = 0; 4505 fw_cmd.pad2 = 0; 4506 4507 for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) { 4508 ret_val = ixgbe_host_interface_command(hw, (u32 *)&fw_cmd, 4509 sizeof(fw_cmd), 4510 IXGBE_HI_COMMAND_TIMEOUT, 4511 TRUE); 4512 if (ret_val != IXGBE_SUCCESS) 4513 continue; 4514 4515 if (fw_cmd.hdr.cmd_or_resp.ret_status == 4516 FW_CEM_RESP_STATUS_SUCCESS) 4517 ret_val = IXGBE_SUCCESS; 4518 else 4519 ret_val = IXGBE_ERR_HOST_INTERFACE_COMMAND; 4520 4521 break; 4522 } 4523 4524 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM); 4525 out: 4526 return ret_val; 4527 } 4528 4529 /** 4530 * ixgbe_set_rxpba_generic - Initialize Rx packet buffer 4531 * @hw: pointer to hardware structure 4532 * @num_pb: number of packet buffers to allocate 4533 * @headroom: reserve n KB of headroom 4534 * @strategy: packet buffer allocation strategy 4535 **/ 4536 void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw, int num_pb, u32 headroom, 4537 int strategy) 4538 { 4539 u32 pbsize = hw->mac.rx_pb_size; 4540 int i = 0; 4541 u32 rxpktsize, txpktsize, txpbthresh; 4542 4543 /* Reserve headroom */ 4544 pbsize -= headroom; 4545 4546 if (!num_pb) 4547 num_pb = 1; 4548 4549 /* Divide remaining packet buffer space amongst the number of packet 4550 * buffers requested using supplied strategy. 4551 */ 4552 switch (strategy) { 4553 case PBA_STRATEGY_WEIGHTED: 4554 /* ixgbe_dcb_pba_80_48 strategy weight first half of packet 4555 * buffer with 5/8 of the packet buffer space. 4556 */ 4557 rxpktsize = (pbsize * 5) / (num_pb * 4); 4558 pbsize -= rxpktsize * (num_pb / 2); 4559 rxpktsize <<= IXGBE_RXPBSIZE_SHIFT; 4560 for (; i < (num_pb / 2); i++) 4561 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize); 4562 /* Fall through to configure remaining packet buffers */ 4563 case PBA_STRATEGY_EQUAL: 4564 rxpktsize = (pbsize / (num_pb - i)) << IXGBE_RXPBSIZE_SHIFT; 4565 for (; i < num_pb; i++) 4566 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize); 4567 break; 4568 default: 4569 break; 4570 } 4571 4572 /* Only support an equally distributed Tx packet buffer strategy. */ 4573 txpktsize = IXGBE_TXPBSIZE_MAX / num_pb; 4574 txpbthresh = (txpktsize / 1024) - IXGBE_TXPKT_SIZE_MAX; 4575 for (i = 0; i < num_pb; i++) { 4576 IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), txpktsize); 4577 IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), txpbthresh); 4578 } 4579 4580 /* Clear unused TCs, if any, to zero buffer size*/ 4581 for (; i < IXGBE_MAX_PB; i++) { 4582 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0); 4583 IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), 0); 4584 IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), 0); 4585 } 4586 } 4587 4588 /** 4589 * ixgbe_clear_tx_pending - Clear pending TX work from the PCIe fifo 4590 * @hw: pointer to the hardware structure 4591 * 4592 * The 82599 and x540 MACs can experience issues if TX work is still pending 4593 * when a reset occurs. This function prevents this by flushing the PCIe 4594 * buffers on the system. 4595 **/ 4596 void ixgbe_clear_tx_pending(struct ixgbe_hw *hw) 4597 { 4598 u32 gcr_ext, hlreg0, i, poll; 4599 u16 value; 4600 4601 /* 4602 * If double reset is not requested then all transactions should 4603 * already be clear and as such there is no work to do 4604 */ 4605 if (!(hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED)) 4606 return; 4607 4608 /* 4609 * Set loopback enable to prevent any transmits from being sent 4610 * should the link come up. This assumes that the RXCTRL.RXEN bit 4611 * has already been cleared. 4612 */ 4613 hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0); 4614 IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0 | IXGBE_HLREG0_LPBK); 4615 4616 /* Wait for a last completion before clearing buffers */ 4617 IXGBE_WRITE_FLUSH(hw); 4618 msec_delay(3); 4619 4620 /* 4621 * Before proceeding, make sure that the PCIe block does not have 4622 * transactions pending. 4623 */ 4624 poll = ixgbe_pcie_timeout_poll(hw); 4625 for (i = 0; i < poll; i++) { 4626 usec_delay(100); 4627 value = IXGBE_READ_PCIE_WORD(hw, IXGBE_PCI_DEVICE_STATUS); 4628 if (IXGBE_REMOVED(hw->hw_addr)) 4629 goto out; 4630 if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING)) 4631 goto out; 4632 } 4633 4634 out: 4635 /* initiate cleaning flow for buffers in the PCIe transaction layer */ 4636 gcr_ext = IXGBE_READ_REG(hw, IXGBE_GCR_EXT); 4637 IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, 4638 gcr_ext | IXGBE_GCR_EXT_BUFFERS_CLEAR); 4639 4640 /* Flush all writes and allow 20usec for all transactions to clear */ 4641 IXGBE_WRITE_FLUSH(hw); 4642 usec_delay(20); 4643 4644 /* restore previous register values */ 4645 IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, gcr_ext); 4646 IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0); 4647 } 4648 4649 4650 /** 4651 * ixgbe_dcb_get_rtrup2tc_generic - read rtrup2tc reg 4652 * @hw: pointer to hardware structure 4653 * @map: pointer to u8 arr for returning map 4654 * 4655 * Read the rtrup2tc HW register and resolve its content into map 4656 **/ 4657 void ixgbe_dcb_get_rtrup2tc_generic(struct ixgbe_hw *hw, u8 *map) 4658 { 4659 u32 reg, i; 4660 4661 reg = IXGBE_READ_REG(hw, IXGBE_RTRUP2TC); 4662 for (i = 0; i < IXGBE_DCB_MAX_USER_PRIORITY; i++) 4663 map[i] = IXGBE_RTRUP2TC_UP_MASK & 4664 (reg >> (i * IXGBE_RTRUP2TC_UP_SHIFT)); 4665 return; 4666 } 4667 4668 void ixgbe_disable_rx_generic(struct ixgbe_hw *hw) 4669 { 4670 u32 pfdtxgswc; 4671 u32 rxctrl; 4672 4673 rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL); 4674 if (rxctrl & IXGBE_RXCTRL_RXEN) { 4675 if (hw->mac.type != ixgbe_mac_82598EB) { 4676 pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC); 4677 if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) { 4678 pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN; 4679 IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc); 4680 hw->mac.set_lben = TRUE; 4681 } else { 4682 hw->mac.set_lben = FALSE; 4683 } 4684 } 4685 rxctrl &= ~IXGBE_RXCTRL_RXEN; 4686 IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl); 4687 } 4688 } 4689 4690 void ixgbe_enable_rx_generic(struct ixgbe_hw *hw) 4691 { 4692 u32 pfdtxgswc; 4693 u32 rxctrl; 4694 4695 rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL); 4696 IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, (rxctrl | IXGBE_RXCTRL_RXEN)); 4697 4698 if (hw->mac.type != ixgbe_mac_82598EB) { 4699 if (hw->mac.set_lben) { 4700 pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC); 4701 pfdtxgswc |= IXGBE_PFDTXGSWC_VT_LBEN; 4702 IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc); 4703 hw->mac.set_lben = FALSE; 4704 } 4705 } 4706 } 4707 4708 /** 4709 * ixgbe_mng_present - returns TRUE when management capability is present 4710 * @hw: pointer to hardware structure 4711 */ 4712 bool ixgbe_mng_present(struct ixgbe_hw *hw) 4713 { 4714 u32 fwsm; 4715 4716 if (hw->mac.type < ixgbe_mac_82599EB) 4717 return FALSE; 4718 4719 fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM); 4720 fwsm &= IXGBE_FWSM_MODE_MASK; 4721 return fwsm == IXGBE_FWSM_FW_MODE_PT; 4722 } 4723 4724 /** 4725 * ixgbe_mng_enabled - Is the manageability engine enabled? 4726 * @hw: pointer to hardware structure 4727 * 4728 * Returns TRUE if the manageability engine is enabled. 4729 **/ 4730 bool ixgbe_mng_enabled(struct ixgbe_hw *hw) 4731 { 4732 u32 fwsm, manc, factps; 4733 4734 fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM); 4735 if ((fwsm & IXGBE_FWSM_MODE_MASK) != IXGBE_FWSM_FW_MODE_PT) 4736 return FALSE; 4737 4738 manc = IXGBE_READ_REG(hw, IXGBE_MANC); 4739 if (!(manc & IXGBE_MANC_RCV_TCO_EN)) 4740 return FALSE; 4741 4742 if (hw->mac.type <= ixgbe_mac_X540) { 4743 factps = IXGBE_READ_REG(hw, IXGBE_FACTPS); 4744 if (factps & IXGBE_FACTPS_MNGCG) 4745 return FALSE; 4746 } 4747 4748 return TRUE; 4749 } 4750 4751 /** 4752 * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed 4753 * @hw: pointer to hardware structure 4754 * @speed: new link speed 4755 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed 4756 * 4757 * Set the link speed in the MAC and/or PHY register and restarts link. 4758 **/ 4759 s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, 4760 ixgbe_link_speed speed, 4761 bool autoneg_wait_to_complete) 4762 { 4763 ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN; 4764 ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN; 4765 s32 status = IXGBE_SUCCESS; 4766 u32 speedcnt = 0; 4767 u32 i = 0; 4768 bool autoneg, link_up = FALSE; 4769 4770 DEBUGFUNC("ixgbe_setup_mac_link_multispeed_fiber"); 4771 4772 /* Mask off requested but non-supported speeds */ 4773 status = ixgbe_get_link_capabilities(hw, &link_speed, &autoneg); 4774 if (status != IXGBE_SUCCESS) 4775 return status; 4776 4777 speed &= link_speed; 4778 4779 /* Try each speed one by one, highest priority first. We do this in 4780 * software because 10Gb fiber doesn't support speed autonegotiation. 4781 */ 4782 if (speed & IXGBE_LINK_SPEED_10GB_FULL) { 4783 speedcnt++; 4784 highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL; 4785 4786 /* If we already have link at this speed, just jump out */ 4787 status = ixgbe_check_link(hw, &link_speed, &link_up, FALSE); 4788 if (status != IXGBE_SUCCESS) 4789 return status; 4790 4791 if ((link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up) 4792 goto out; 4793 4794 /* Set the module link speed */ 4795 switch (hw->phy.media_type) { 4796 case ixgbe_media_type_fiber_fixed: 4797 case ixgbe_media_type_fiber: 4798 ixgbe_set_rate_select_speed(hw, 4799 IXGBE_LINK_SPEED_10GB_FULL); 4800 break; 4801 case ixgbe_media_type_fiber_qsfp: 4802 /* QSFP module automatically detects MAC link speed */ 4803 break; 4804 default: 4805 DEBUGOUT("Unexpected media type.\n"); 4806 break; 4807 } 4808 4809 /* Allow module to change analog characteristics (1G->10G) */ 4810 msec_delay(40); 4811 4812 status = ixgbe_setup_mac_link(hw, 4813 IXGBE_LINK_SPEED_10GB_FULL, 4814 autoneg_wait_to_complete); 4815 if (status != IXGBE_SUCCESS) 4816 return status; 4817 4818 /* Flap the Tx laser if it has not already been done */ 4819 ixgbe_flap_tx_laser(hw); 4820 4821 /* Wait for the controller to acquire link. Per IEEE 802.3ap, 4822 * Section 73.10.2, we may have to wait up to 500ms if KR is 4823 * attempted. 82599 uses the same timing for 10g SFI. 4824 */ 4825 for (i = 0; i < 5; i++) { 4826 /* Wait for the link partner to also set speed */ 4827 msec_delay(100); 4828 4829 /* If we have link, just jump out */ 4830 status = ixgbe_check_link(hw, &link_speed, 4831 &link_up, FALSE); 4832 if (status != IXGBE_SUCCESS) 4833 return status; 4834 4835 if (link_up) 4836 goto out; 4837 } 4838 } 4839 4840 if (speed & IXGBE_LINK_SPEED_1GB_FULL) { 4841 speedcnt++; 4842 if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN) 4843 highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL; 4844 4845 /* If we already have link at this speed, just jump out */ 4846 status = ixgbe_check_link(hw, &link_speed, &link_up, FALSE); 4847 if (status != IXGBE_SUCCESS) 4848 return status; 4849 4850 if ((link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up) 4851 goto out; 4852 4853 /* Set the module link speed */ 4854 switch (hw->phy.media_type) { 4855 case ixgbe_media_type_fiber_fixed: 4856 case ixgbe_media_type_fiber: 4857 ixgbe_set_rate_select_speed(hw, 4858 IXGBE_LINK_SPEED_1GB_FULL); 4859 break; 4860 case ixgbe_media_type_fiber_qsfp: 4861 /* QSFP module automatically detects link speed */ 4862 break; 4863 default: 4864 DEBUGOUT("Unexpected media type.\n"); 4865 break; 4866 } 4867 4868 /* Allow module to change analog characteristics (10G->1G) */ 4869 msec_delay(40); 4870 4871 status = ixgbe_setup_mac_link(hw, 4872 IXGBE_LINK_SPEED_1GB_FULL, 4873 autoneg_wait_to_complete); 4874 if (status != IXGBE_SUCCESS) 4875 return status; 4876 4877 /* Flap the Tx laser if it has not already been done */ 4878 ixgbe_flap_tx_laser(hw); 4879 4880 /* Wait for the link partner to also set speed */ 4881 msec_delay(100); 4882 4883 /* If we have link, just jump out */ 4884 status = ixgbe_check_link(hw, &link_speed, &link_up, FALSE); 4885 if (status != IXGBE_SUCCESS) 4886 return status; 4887 4888 if (link_up) 4889 goto out; 4890 } 4891 4892 /* We didn't get link. Configure back to the highest speed we tried, 4893 * (if there was more than one). We call ourselves back with just the 4894 * single highest speed that the user requested. 4895 */ 4896 if (speedcnt > 1) 4897 status = ixgbe_setup_mac_link_multispeed_fiber(hw, 4898 highest_link_speed, 4899 autoneg_wait_to_complete); 4900 4901 out: 4902 /* Set autoneg_advertised value based on input link speed */ 4903 hw->phy.autoneg_advertised = 0; 4904 4905 if (speed & IXGBE_LINK_SPEED_10GB_FULL) 4906 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; 4907 4908 if (speed & IXGBE_LINK_SPEED_1GB_FULL) 4909 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; 4910 4911 return status; 4912 } 4913 4914 /** 4915 * ixgbe_set_soft_rate_select_speed - Set module link speed 4916 * @hw: pointer to hardware structure 4917 * @speed: link speed to set 4918 * 4919 * Set module link speed via the soft rate select. 4920 */ 4921 void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw, 4922 ixgbe_link_speed speed) 4923 { 4924 s32 status; 4925 u8 rs, eeprom_data; 4926 4927 switch (speed) { 4928 case IXGBE_LINK_SPEED_10GB_FULL: 4929 /* one bit mask same as setting on */ 4930 rs = IXGBE_SFF_SOFT_RS_SELECT_10G; 4931 break; 4932 case IXGBE_LINK_SPEED_1GB_FULL: 4933 rs = IXGBE_SFF_SOFT_RS_SELECT_1G; 4934 break; 4935 default: 4936 DEBUGOUT("Invalid fixed module speed\n"); 4937 return; 4938 } 4939 4940 /* Set RS0 */ 4941 status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, 4942 IXGBE_I2C_EEPROM_DEV_ADDR2, 4943 &eeprom_data); 4944 if (status) { 4945 DEBUGOUT("Failed to read Rx Rate Select RS0\n"); 4946 goto out; 4947 } 4948 4949 eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs; 4950 4951 status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, 4952 IXGBE_I2C_EEPROM_DEV_ADDR2, 4953 eeprom_data); 4954 if (status) { 4955 DEBUGOUT("Failed to write Rx Rate Select RS0\n"); 4956 goto out; 4957 } 4958 4959 /* Set RS1 */ 4960 status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB, 4961 IXGBE_I2C_EEPROM_DEV_ADDR2, 4962 &eeprom_data); 4963 if (status) { 4964 DEBUGOUT("Failed to read Rx Rate Select RS1\n"); 4965 goto out; 4966 } 4967 4968 eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs; 4969 4970 status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB, 4971 IXGBE_I2C_EEPROM_DEV_ADDR2, 4972 eeprom_data); 4973 if (status) { 4974 DEBUGOUT("Failed to write Rx Rate Select RS1\n"); 4975 goto out; 4976 } 4977 out: 4978 return; 4979 } 4980