1 /* 2 * Copyright (c) 1997, 1998 3 * Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer. 10 * 2. Redistributions in binary form must reproduce the above copyright 11 * notice, this list of conditions and the following disclaimer in the 12 * documentation and/or other materials provided with the distribution. 13 * 3. All advertising materials mentioning features or use of this software 14 * must display the following acknowledgement: 15 * This product includes software developed by Bill Paul. 16 * 4. Neither the name of the author nor the names of any co-contributors 17 * may be used to endorse or promote products derived from this software 18 * without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 21 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 24 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 30 * THE POSSIBILITY OF SUCH DAMAGE. 31 * 32 * $FreeBSD: src/sys/pci/if_tl.c,v 1.51.2.5 2001/12/16 15:46:08 luigi Exp $ 33 * $DragonFly: src/sys/dev/netif/tl/if_tl.c,v 1.9 2004/03/23 22:19:04 hsu Exp $ 34 * 35 * $FreeBSD: src/sys/pci/if_tl.c,v 1.51.2.5 2001/12/16 15:46:08 luigi Exp $ 36 */ 37 38 /* 39 * Texas Instruments ThunderLAN driver for FreeBSD 2.2.6 and 3.x. 40 * Supports many Compaq PCI NICs based on the ThunderLAN ethernet controller, 41 * the National Semiconductor DP83840A physical interface and the 42 * Microchip Technology 24Cxx series serial EEPROM. 43 * 44 * Written using the following four documents: 45 * 46 * Texas Instruments ThunderLAN Programmer's Guide (www.ti.com) 47 * National Semiconductor DP83840A data sheet (www.national.com) 48 * Microchip Technology 24C02C data sheet (www.microchip.com) 49 * Micro Linear ML6692 100BaseTX only PHY data sheet (www.microlinear.com) 50 * 51 * Written by Bill Paul <wpaul@ctr.columbia.edu> 52 * Electrical Engineering Department 53 * Columbia University, New York City 54 */ 55 56 /* 57 * Some notes about the ThunderLAN: 58 * 59 * The ThunderLAN controller is a single chip containing PCI controller 60 * logic, approximately 3K of on-board SRAM, a LAN controller, and media 61 * independent interface (MII) bus. The MII allows the ThunderLAN chip to 62 * control up to 32 different physical interfaces (PHYs). The ThunderLAN 63 * also has a built-in 10baseT PHY, allowing a single ThunderLAN controller 64 * to act as a complete ethernet interface. 65 * 66 * Other PHYs may be attached to the ThunderLAN; the Compaq 10/100 cards 67 * use a National Semiconductor DP83840A PHY that supports 10 or 100Mb/sec 68 * in full or half duplex. Some of the Compaq Deskpro machines use a 69 * Level 1 LXT970 PHY with the same capabilities. Certain Olicom adapters 70 * use a Micro Linear ML6692 100BaseTX only PHY, which can be used in 71 * concert with the ThunderLAN's internal PHY to provide full 10/100 72 * support. This is cheaper than using a standalone external PHY for both 73 * 10/100 modes and letting the ThunderLAN's internal PHY go to waste. 74 * A serial EEPROM is also attached to the ThunderLAN chip to provide 75 * power-up default register settings and for storing the adapter's 76 * station address. Although not supported by this driver, the ThunderLAN 77 * chip can also be connected to token ring PHYs. 78 * 79 * The ThunderLAN has a set of registers which can be used to issue 80 * commands, acknowledge interrupts, and to manipulate other internal 81 * registers on its DIO bus. The primary registers can be accessed 82 * using either programmed I/O (inb/outb) or via PCI memory mapping, 83 * depending on how the card is configured during the PCI probing 84 * phase. It is even possible to have both PIO and memory mapped 85 * access turned on at the same time. 86 * 87 * Frame reception and transmission with the ThunderLAN chip is done 88 * using frame 'lists.' A list structure looks more or less like this: 89 * 90 * struct tl_frag { 91 * u_int32_t fragment_address; 92 * u_int32_t fragment_size; 93 * }; 94 * struct tl_list { 95 * u_int32_t forward_pointer; 96 * u_int16_t cstat; 97 * u_int16_t frame_size; 98 * struct tl_frag fragments[10]; 99 * }; 100 * 101 * The forward pointer in the list header can be either a 0 or the address 102 * of another list, which allows several lists to be linked together. Each 103 * list contains up to 10 fragment descriptors. This means the chip allows 104 * ethernet frames to be broken up into up to 10 chunks for transfer to 105 * and from the SRAM. Note that the forward pointer and fragment buffer 106 * addresses are physical memory addresses, not virtual. Note also that 107 * a single ethernet frame can not span lists: if the host wants to 108 * transmit a frame and the frame data is split up over more than 10 109 * buffers, the frame has to collapsed before it can be transmitted. 110 * 111 * To receive frames, the driver sets up a number of lists and populates 112 * the fragment descriptors, then it sends an RX GO command to the chip. 113 * When a frame is received, the chip will DMA it into the memory regions 114 * specified by the fragment descriptors and then trigger an RX 'end of 115 * frame interrupt' when done. The driver may choose to use only one 116 * fragment per list; this may result is slighltly less efficient use 117 * of memory in exchange for improving performance. 118 * 119 * To transmit frames, the driver again sets up lists and fragment 120 * descriptors, only this time the buffers contain frame data that 121 * is to be DMA'ed into the chip instead of out of it. Once the chip 122 * has transfered the data into its on-board SRAM, it will trigger a 123 * TX 'end of frame' interrupt. It will also generate an 'end of channel' 124 * interrupt when it reaches the end of the list. 125 */ 126 127 /* 128 * Some notes about this driver: 129 * 130 * The ThunderLAN chip provides a couple of different ways to organize 131 * reception, transmission and interrupt handling. The simplest approach 132 * is to use one list each for transmission and reception. In this mode, 133 * the ThunderLAN will generate two interrupts for every received frame 134 * (one RX EOF and one RX EOC) and two for each transmitted frame (one 135 * TX EOF and one TX EOC). This may make the driver simpler but it hurts 136 * performance to have to handle so many interrupts. 137 * 138 * Initially I wanted to create a circular list of receive buffers so 139 * that the ThunderLAN chip would think there was an infinitely long 140 * receive channel and never deliver an RXEOC interrupt. However this 141 * doesn't work correctly under heavy load: while the manual says the 142 * chip will trigger an RXEOF interrupt each time a frame is copied into 143 * memory, you can't count on the chip waiting around for you to acknowledge 144 * the interrupt before it starts trying to DMA the next frame. The result 145 * is that the chip might traverse the entire circular list and then wrap 146 * around before you have a chance to do anything about it. Consequently, 147 * the receive list is terminated (with a 0 in the forward pointer in the 148 * last element). Each time an RXEOF interrupt arrives, the used list 149 * is shifted to the end of the list. This gives the appearance of an 150 * infinitely large RX chain so long as the driver doesn't fall behind 151 * the chip and allow all of the lists to be filled up. 152 * 153 * If all the lists are filled, the adapter will deliver an RX 'end of 154 * channel' interrupt when it hits the 0 forward pointer at the end of 155 * the chain. The RXEOC handler then cleans out the RX chain and resets 156 * the list head pointer in the ch_parm register and restarts the receiver. 157 * 158 * For frame transmission, it is possible to program the ThunderLAN's 159 * transmit interrupt threshold so that the chip can acknowledge multiple 160 * lists with only a single TX EOF interrupt. This allows the driver to 161 * queue several frames in one shot, and only have to handle a total 162 * two interrupts (one TX EOF and one TX EOC) no matter how many frames 163 * are transmitted. Frame transmission is done directly out of the 164 * mbufs passed to the tl_start() routine via the interface send queue. 165 * The driver simply sets up the fragment descriptors in the transmit 166 * lists to point to the mbuf data regions and sends a TX GO command. 167 * 168 * Note that since the RX and TX lists themselves are always used 169 * only by the driver, the are malloc()ed once at driver initialization 170 * time and never free()ed. 171 * 172 * Also, in order to remain as platform independent as possible, this 173 * driver uses memory mapped register access to manipulate the card 174 * as opposed to programmed I/O. This avoids the use of the inb/outb 175 * (and related) instructions which are specific to the i386 platform. 176 * 177 * Using these techniques, this driver achieves very high performance 178 * by minimizing the amount of interrupts generated during large 179 * transfers and by completely avoiding buffer copies. Frame transfer 180 * to and from the ThunderLAN chip is performed entirely by the chip 181 * itself thereby reducing the load on the host CPU. 182 */ 183 184 #include <sys/param.h> 185 #include <sys/systm.h> 186 #include <sys/sockio.h> 187 #include <sys/mbuf.h> 188 #include <sys/malloc.h> 189 #include <sys/kernel.h> 190 #include <sys/socket.h> 191 192 #include <net/if.h> 193 #include <net/if_arp.h> 194 #include <net/ethernet.h> 195 #include <net/if_dl.h> 196 #include <net/if_media.h> 197 198 #include <net/bpf.h> 199 200 #include <vm/vm.h> /* for vtophys */ 201 #include <vm/pmap.h> /* for vtophys */ 202 #include <machine/clock.h> /* for DELAY */ 203 #include <machine/bus_memio.h> 204 #include <machine/bus_pio.h> 205 #include <machine/bus.h> 206 #include <machine/resource.h> 207 #include <sys/bus.h> 208 #include <sys/rman.h> 209 210 #include "../mii_layer/mii.h" 211 #include "../mii_layer/miivar.h" 212 213 #include <bus/pci/pcireg.h> 214 #include <bus/pci/pcivar.h> 215 216 /* 217 * Default to using PIO register access mode to pacify certain 218 * laptop docking stations with built-in ThunderLAN chips that 219 * don't seem to handle memory mapped mode properly. 220 */ 221 #define TL_USEIOSPACE 222 223 #include "if_tlreg.h" 224 225 /* "controller miibus0" required. See GENERIC if you get errors here. */ 226 #include "miibus_if.h" 227 228 /* 229 * Various supported device vendors/types and their names. 230 */ 231 232 static struct tl_type tl_devs[] = { 233 { TI_VENDORID, TI_DEVICEID_THUNDERLAN, 234 "Texas Instruments ThunderLAN" }, 235 { COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10, 236 "Compaq Netelligent 10" }, 237 { COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_100, 238 "Compaq Netelligent 10/100" }, 239 { COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_100_PROLIANT, 240 "Compaq Netelligent 10/100 Proliant" }, 241 { COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_100_DUAL, 242 "Compaq Netelligent 10/100 Dual Port" }, 243 { COMPAQ_VENDORID, COMPAQ_DEVICEID_NETFLEX_3P_INTEGRATED, 244 "Compaq NetFlex-3/P Integrated" }, 245 { COMPAQ_VENDORID, COMPAQ_DEVICEID_NETFLEX_3P, 246 "Compaq NetFlex-3/P" }, 247 { COMPAQ_VENDORID, COMPAQ_DEVICEID_NETFLEX_3P_BNC, 248 "Compaq NetFlex 3/P w/ BNC" }, 249 { COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_100_EMBEDDED, 250 "Compaq Netelligent 10/100 TX Embedded UTP" }, 251 { COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_T2_UTP_COAX, 252 "Compaq Netelligent 10 T/2 PCI UTP/Coax" }, 253 { COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_100_TX_UTP, 254 "Compaq Netelligent 10/100 TX UTP" }, 255 { OLICOM_VENDORID, OLICOM_DEVICEID_OC2183, 256 "Olicom OC-2183/2185" }, 257 { OLICOM_VENDORID, OLICOM_DEVICEID_OC2325, 258 "Olicom OC-2325" }, 259 { OLICOM_VENDORID, OLICOM_DEVICEID_OC2326, 260 "Olicom OC-2326 10/100 TX UTP" }, 261 { 0, 0, NULL } 262 }; 263 264 static int tl_probe (device_t); 265 static int tl_attach (device_t); 266 static int tl_detach (device_t); 267 static int tl_intvec_rxeoc (void *, u_int32_t); 268 static int tl_intvec_txeoc (void *, u_int32_t); 269 static int tl_intvec_txeof (void *, u_int32_t); 270 static int tl_intvec_rxeof (void *, u_int32_t); 271 static int tl_intvec_adchk (void *, u_int32_t); 272 static int tl_intvec_netsts (void *, u_int32_t); 273 274 static int tl_newbuf (struct tl_softc *, 275 struct tl_chain_onefrag *); 276 static void tl_stats_update (void *); 277 static int tl_encap (struct tl_softc *, struct tl_chain *, 278 struct mbuf *); 279 280 static void tl_intr (void *); 281 static void tl_start (struct ifnet *); 282 static int tl_ioctl (struct ifnet *, u_long, caddr_t, 283 struct ucred *); 284 static void tl_init (void *); 285 static void tl_stop (struct tl_softc *); 286 static void tl_watchdog (struct ifnet *); 287 static void tl_shutdown (device_t); 288 static int tl_ifmedia_upd (struct ifnet *); 289 static void tl_ifmedia_sts (struct ifnet *, struct ifmediareq *); 290 291 static u_int8_t tl_eeprom_putbyte (struct tl_softc *, int); 292 static u_int8_t tl_eeprom_getbyte (struct tl_softc *, 293 int, u_int8_t *); 294 static int tl_read_eeprom (struct tl_softc *, caddr_t, int, int); 295 296 static void tl_mii_sync (struct tl_softc *); 297 static void tl_mii_send (struct tl_softc *, u_int32_t, int); 298 static int tl_mii_readreg (struct tl_softc *, struct tl_mii_frame *); 299 static int tl_mii_writereg (struct tl_softc *, struct tl_mii_frame *); 300 static int tl_miibus_readreg (device_t, int, int); 301 static int tl_miibus_writereg (device_t, int, int, int); 302 static void tl_miibus_statchg (device_t); 303 304 static void tl_setmode (struct tl_softc *, int); 305 static int tl_calchash (caddr_t); 306 static void tl_setmulti (struct tl_softc *); 307 static void tl_setfilt (struct tl_softc *, caddr_t, int); 308 static void tl_softreset (struct tl_softc *, int); 309 static void tl_hardreset (device_t); 310 static int tl_list_rx_init (struct tl_softc *); 311 static int tl_list_tx_init (struct tl_softc *); 312 313 static u_int8_t tl_dio_read8 (struct tl_softc *, int); 314 static u_int16_t tl_dio_read16 (struct tl_softc *, int); 315 static u_int32_t tl_dio_read32 (struct tl_softc *, int); 316 static void tl_dio_write8 (struct tl_softc *, int, int); 317 static void tl_dio_write16 (struct tl_softc *, int, int); 318 static void tl_dio_write32 (struct tl_softc *, int, int); 319 static void tl_dio_setbit (struct tl_softc *, int, int); 320 static void tl_dio_clrbit (struct tl_softc *, int, int); 321 static void tl_dio_setbit16 (struct tl_softc *, int, int); 322 static void tl_dio_clrbit16 (struct tl_softc *, int, int); 323 324 #ifdef TL_USEIOSPACE 325 #define TL_RES SYS_RES_IOPORT 326 #define TL_RID TL_PCI_LOIO 327 #else 328 #define TL_RES SYS_RES_MEMORY 329 #define TL_RID TL_PCI_LOMEM 330 #endif 331 332 static device_method_t tl_methods[] = { 333 /* Device interface */ 334 DEVMETHOD(device_probe, tl_probe), 335 DEVMETHOD(device_attach, tl_attach), 336 DEVMETHOD(device_detach, tl_detach), 337 DEVMETHOD(device_shutdown, tl_shutdown), 338 339 /* bus interface */ 340 DEVMETHOD(bus_print_child, bus_generic_print_child), 341 DEVMETHOD(bus_driver_added, bus_generic_driver_added), 342 343 /* MII interface */ 344 DEVMETHOD(miibus_readreg, tl_miibus_readreg), 345 DEVMETHOD(miibus_writereg, tl_miibus_writereg), 346 DEVMETHOD(miibus_statchg, tl_miibus_statchg), 347 348 { 0, 0 } 349 }; 350 351 static driver_t tl_driver = { 352 "tl", 353 tl_methods, 354 sizeof(struct tl_softc) 355 }; 356 357 static devclass_t tl_devclass; 358 359 DECLARE_DUMMY_MODULE(if_tl); 360 DRIVER_MODULE(if_tl, pci, tl_driver, tl_devclass, 0, 0); 361 DRIVER_MODULE(miibus, tl, miibus_driver, miibus_devclass, 0, 0); 362 363 static u_int8_t tl_dio_read8(sc, reg) 364 struct tl_softc *sc; 365 int reg; 366 { 367 CSR_WRITE_2(sc, TL_DIO_ADDR, reg); 368 return(CSR_READ_1(sc, TL_DIO_DATA + (reg & 3))); 369 } 370 371 static u_int16_t tl_dio_read16(sc, reg) 372 struct tl_softc *sc; 373 int reg; 374 { 375 CSR_WRITE_2(sc, TL_DIO_ADDR, reg); 376 return(CSR_READ_2(sc, TL_DIO_DATA + (reg & 3))); 377 } 378 379 static u_int32_t tl_dio_read32(sc, reg) 380 struct tl_softc *sc; 381 int reg; 382 { 383 CSR_WRITE_2(sc, TL_DIO_ADDR, reg); 384 return(CSR_READ_4(sc, TL_DIO_DATA + (reg & 3))); 385 } 386 387 static void tl_dio_write8(sc, reg, val) 388 struct tl_softc *sc; 389 int reg; 390 int val; 391 { 392 CSR_WRITE_2(sc, TL_DIO_ADDR, reg); 393 CSR_WRITE_1(sc, TL_DIO_DATA + (reg & 3), val); 394 return; 395 } 396 397 static void tl_dio_write16(sc, reg, val) 398 struct tl_softc *sc; 399 int reg; 400 int val; 401 { 402 CSR_WRITE_2(sc, TL_DIO_ADDR, reg); 403 CSR_WRITE_2(sc, TL_DIO_DATA + (reg & 3), val); 404 return; 405 } 406 407 static void tl_dio_write32(sc, reg, val) 408 struct tl_softc *sc; 409 int reg; 410 int val; 411 { 412 CSR_WRITE_2(sc, TL_DIO_ADDR, reg); 413 CSR_WRITE_4(sc, TL_DIO_DATA + (reg & 3), val); 414 return; 415 } 416 417 static void tl_dio_setbit(sc, reg, bit) 418 struct tl_softc *sc; 419 int reg; 420 int bit; 421 { 422 u_int8_t f; 423 424 CSR_WRITE_2(sc, TL_DIO_ADDR, reg); 425 f = CSR_READ_1(sc, TL_DIO_DATA + (reg & 3)); 426 f |= bit; 427 CSR_WRITE_1(sc, TL_DIO_DATA + (reg & 3), f); 428 429 return; 430 } 431 432 static void tl_dio_clrbit(sc, reg, bit) 433 struct tl_softc *sc; 434 int reg; 435 int bit; 436 { 437 u_int8_t f; 438 439 CSR_WRITE_2(sc, TL_DIO_ADDR, reg); 440 f = CSR_READ_1(sc, TL_DIO_DATA + (reg & 3)); 441 f &= ~bit; 442 CSR_WRITE_1(sc, TL_DIO_DATA + (reg & 3), f); 443 444 return; 445 } 446 447 static void tl_dio_setbit16(sc, reg, bit) 448 struct tl_softc *sc; 449 int reg; 450 int bit; 451 { 452 u_int16_t f; 453 454 CSR_WRITE_2(sc, TL_DIO_ADDR, reg); 455 f = CSR_READ_2(sc, TL_DIO_DATA + (reg & 3)); 456 f |= bit; 457 CSR_WRITE_2(sc, TL_DIO_DATA + (reg & 3), f); 458 459 return; 460 } 461 462 static void tl_dio_clrbit16(sc, reg, bit) 463 struct tl_softc *sc; 464 int reg; 465 int bit; 466 { 467 u_int16_t f; 468 469 CSR_WRITE_2(sc, TL_DIO_ADDR, reg); 470 f = CSR_READ_2(sc, TL_DIO_DATA + (reg & 3)); 471 f &= ~bit; 472 CSR_WRITE_2(sc, TL_DIO_DATA + (reg & 3), f); 473 474 return; 475 } 476 477 /* 478 * Send an instruction or address to the EEPROM, check for ACK. 479 */ 480 static u_int8_t tl_eeprom_putbyte(sc, byte) 481 struct tl_softc *sc; 482 int byte; 483 { 484 int i, ack = 0; 485 486 /* 487 * Make sure we're in TX mode. 488 */ 489 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ETXEN); 490 491 /* 492 * Feed in each bit and stobe the clock. 493 */ 494 for (i = 0x80; i; i >>= 1) { 495 if (byte & i) { 496 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_EDATA); 497 } else { 498 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_EDATA); 499 } 500 DELAY(1); 501 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ECLOK); 502 DELAY(1); 503 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ECLOK); 504 } 505 506 /* 507 * Turn off TX mode. 508 */ 509 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ETXEN); 510 511 /* 512 * Check for ack. 513 */ 514 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ECLOK); 515 ack = tl_dio_read8(sc, TL_NETSIO) & TL_SIO_EDATA; 516 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ECLOK); 517 518 return(ack); 519 } 520 521 /* 522 * Read a byte of data stored in the EEPROM at address 'addr.' 523 */ 524 static u_int8_t tl_eeprom_getbyte(sc, addr, dest) 525 struct tl_softc *sc; 526 int addr; 527 u_int8_t *dest; 528 { 529 int i; 530 u_int8_t byte = 0; 531 532 tl_dio_write8(sc, TL_NETSIO, 0); 533 534 EEPROM_START; 535 536 /* 537 * Send write control code to EEPROM. 538 */ 539 if (tl_eeprom_putbyte(sc, EEPROM_CTL_WRITE)) { 540 printf("tl%d: failed to send write command, status: %x\n", 541 sc->tl_unit, tl_dio_read8(sc, TL_NETSIO)); 542 return(1); 543 } 544 545 /* 546 * Send address of byte we want to read. 547 */ 548 if (tl_eeprom_putbyte(sc, addr)) { 549 printf("tl%d: failed to send address, status: %x\n", 550 sc->tl_unit, tl_dio_read8(sc, TL_NETSIO)); 551 return(1); 552 } 553 554 EEPROM_STOP; 555 EEPROM_START; 556 /* 557 * Send read control code to EEPROM. 558 */ 559 if (tl_eeprom_putbyte(sc, EEPROM_CTL_READ)) { 560 printf("tl%d: failed to send write command, status: %x\n", 561 sc->tl_unit, tl_dio_read8(sc, TL_NETSIO)); 562 return(1); 563 } 564 565 /* 566 * Start reading bits from EEPROM. 567 */ 568 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ETXEN); 569 for (i = 0x80; i; i >>= 1) { 570 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ECLOK); 571 DELAY(1); 572 if (tl_dio_read8(sc, TL_NETSIO) & TL_SIO_EDATA) 573 byte |= i; 574 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ECLOK); 575 DELAY(1); 576 } 577 578 EEPROM_STOP; 579 580 /* 581 * No ACK generated for read, so just return byte. 582 */ 583 584 *dest = byte; 585 586 return(0); 587 } 588 589 /* 590 * Read a sequence of bytes from the EEPROM. 591 */ 592 static int tl_read_eeprom(sc, dest, off, cnt) 593 struct tl_softc *sc; 594 caddr_t dest; 595 int off; 596 int cnt; 597 { 598 int err = 0, i; 599 u_int8_t byte = 0; 600 601 for (i = 0; i < cnt; i++) { 602 err = tl_eeprom_getbyte(sc, off + i, &byte); 603 if (err) 604 break; 605 *(dest + i) = byte; 606 } 607 608 return(err ? 1 : 0); 609 } 610 611 static void tl_mii_sync(sc) 612 struct tl_softc *sc; 613 { 614 int i; 615 616 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MTXEN); 617 618 for (i = 0; i < 32; i++) { 619 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK); 620 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK); 621 } 622 623 return; 624 } 625 626 static void tl_mii_send(sc, bits, cnt) 627 struct tl_softc *sc; 628 u_int32_t bits; 629 int cnt; 630 { 631 int i; 632 633 for (i = (0x1 << (cnt - 1)); i; i >>= 1) { 634 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK); 635 if (bits & i) { 636 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MDATA); 637 } else { 638 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MDATA); 639 } 640 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK); 641 } 642 } 643 644 static int tl_mii_readreg(sc, frame) 645 struct tl_softc *sc; 646 struct tl_mii_frame *frame; 647 648 { 649 int i, ack, s; 650 int minten = 0; 651 652 s = splimp(); 653 654 tl_mii_sync(sc); 655 656 /* 657 * Set up frame for RX. 658 */ 659 frame->mii_stdelim = TL_MII_STARTDELIM; 660 frame->mii_opcode = TL_MII_READOP; 661 frame->mii_turnaround = 0; 662 frame->mii_data = 0; 663 664 /* 665 * Turn off MII interrupt by forcing MINTEN low. 666 */ 667 minten = tl_dio_read8(sc, TL_NETSIO) & TL_SIO_MINTEN; 668 if (minten) { 669 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MINTEN); 670 } 671 672 /* 673 * Turn on data xmit. 674 */ 675 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MTXEN); 676 677 /* 678 * Send command/address info. 679 */ 680 tl_mii_send(sc, frame->mii_stdelim, 2); 681 tl_mii_send(sc, frame->mii_opcode, 2); 682 tl_mii_send(sc, frame->mii_phyaddr, 5); 683 tl_mii_send(sc, frame->mii_regaddr, 5); 684 685 /* 686 * Turn off xmit. 687 */ 688 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MTXEN); 689 690 /* Idle bit */ 691 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK); 692 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK); 693 694 /* Check for ack */ 695 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK); 696 ack = tl_dio_read8(sc, TL_NETSIO) & TL_SIO_MDATA; 697 698 /* Complete the cycle */ 699 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK); 700 701 /* 702 * Now try reading data bits. If the ack failed, we still 703 * need to clock through 16 cycles to keep the PHYs in sync. 704 */ 705 if (ack) { 706 for(i = 0; i < 16; i++) { 707 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK); 708 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK); 709 } 710 goto fail; 711 } 712 713 for (i = 0x8000; i; i >>= 1) { 714 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK); 715 if (!ack) { 716 if (tl_dio_read8(sc, TL_NETSIO) & TL_SIO_MDATA) 717 frame->mii_data |= i; 718 } 719 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK); 720 } 721 722 fail: 723 724 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK); 725 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK); 726 727 /* Reenable interrupts */ 728 if (minten) { 729 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MINTEN); 730 } 731 732 splx(s); 733 734 if (ack) 735 return(1); 736 return(0); 737 } 738 739 static int tl_mii_writereg(sc, frame) 740 struct tl_softc *sc; 741 struct tl_mii_frame *frame; 742 743 { 744 int s; 745 int minten; 746 747 tl_mii_sync(sc); 748 749 s = splimp(); 750 /* 751 * Set up frame for TX. 752 */ 753 754 frame->mii_stdelim = TL_MII_STARTDELIM; 755 frame->mii_opcode = TL_MII_WRITEOP; 756 frame->mii_turnaround = TL_MII_TURNAROUND; 757 758 /* 759 * Turn off MII interrupt by forcing MINTEN low. 760 */ 761 minten = tl_dio_read8(sc, TL_NETSIO) & TL_SIO_MINTEN; 762 if (minten) { 763 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MINTEN); 764 } 765 766 /* 767 * Turn on data output. 768 */ 769 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MTXEN); 770 771 tl_mii_send(sc, frame->mii_stdelim, 2); 772 tl_mii_send(sc, frame->mii_opcode, 2); 773 tl_mii_send(sc, frame->mii_phyaddr, 5); 774 tl_mii_send(sc, frame->mii_regaddr, 5); 775 tl_mii_send(sc, frame->mii_turnaround, 2); 776 tl_mii_send(sc, frame->mii_data, 16); 777 778 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK); 779 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK); 780 781 /* 782 * Turn off xmit. 783 */ 784 tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MTXEN); 785 786 /* Reenable interrupts */ 787 if (minten) 788 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MINTEN); 789 790 splx(s); 791 792 return(0); 793 } 794 795 static int tl_miibus_readreg(dev, phy, reg) 796 device_t dev; 797 int phy, reg; 798 { 799 struct tl_softc *sc; 800 struct tl_mii_frame frame; 801 802 sc = device_get_softc(dev); 803 bzero((char *)&frame, sizeof(frame)); 804 805 frame.mii_phyaddr = phy; 806 frame.mii_regaddr = reg; 807 tl_mii_readreg(sc, &frame); 808 809 return(frame.mii_data); 810 } 811 812 static int tl_miibus_writereg(dev, phy, reg, data) 813 device_t dev; 814 int phy, reg, data; 815 { 816 struct tl_softc *sc; 817 struct tl_mii_frame frame; 818 819 sc = device_get_softc(dev); 820 bzero((char *)&frame, sizeof(frame)); 821 822 frame.mii_phyaddr = phy; 823 frame.mii_regaddr = reg; 824 frame.mii_data = data; 825 826 tl_mii_writereg(sc, &frame); 827 828 return(0); 829 } 830 831 static void tl_miibus_statchg(dev) 832 device_t dev; 833 { 834 struct tl_softc *sc; 835 struct mii_data *mii; 836 837 sc = device_get_softc(dev); 838 mii = device_get_softc(sc->tl_miibus); 839 840 if ((mii->mii_media_active & IFM_GMASK) == IFM_FDX) { 841 tl_dio_setbit(sc, TL_NETCMD, TL_CMD_DUPLEX); 842 } else { 843 tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_DUPLEX); 844 } 845 846 return; 847 } 848 849 /* 850 * Set modes for bitrate devices. 851 */ 852 static void tl_setmode(sc, media) 853 struct tl_softc *sc; 854 int media; 855 { 856 if (IFM_SUBTYPE(media) == IFM_10_5) 857 tl_dio_setbit(sc, TL_ACOMMIT, TL_AC_MTXD1); 858 if (IFM_SUBTYPE(media) == IFM_10_T) { 859 tl_dio_clrbit(sc, TL_ACOMMIT, TL_AC_MTXD1); 860 if ((media & IFM_GMASK) == IFM_FDX) { 861 tl_dio_clrbit(sc, TL_ACOMMIT, TL_AC_MTXD3); 862 tl_dio_setbit(sc, TL_NETCMD, TL_CMD_DUPLEX); 863 } else { 864 tl_dio_setbit(sc, TL_ACOMMIT, TL_AC_MTXD3); 865 tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_DUPLEX); 866 } 867 } 868 869 return; 870 } 871 872 /* 873 * Calculate the hash of a MAC address for programming the multicast hash 874 * table. This hash is simply the address split into 6-bit chunks 875 * XOR'd, e.g. 876 * byte: 000000|00 1111|1111 22|222222|333333|33 4444|4444 55|555555 877 * bit: 765432|10 7654|3210 76|543210|765432|10 7654|3210 76|543210 878 * Bytes 0-2 and 3-5 are symmetrical, so are folded together. Then 879 * the folded 24-bit value is split into 6-bit portions and XOR'd. 880 */ 881 static int tl_calchash(addr) 882 caddr_t addr; 883 { 884 int t; 885 886 t = (addr[0] ^ addr[3]) << 16 | (addr[1] ^ addr[4]) << 8 | 887 (addr[2] ^ addr[5]); 888 return ((t >> 18) ^ (t >> 12) ^ (t >> 6) ^ t) & 0x3f; 889 } 890 891 /* 892 * The ThunderLAN has a perfect MAC address filter in addition to 893 * the multicast hash filter. The perfect filter can be programmed 894 * with up to four MAC addresses. The first one is always used to 895 * hold the station address, which leaves us free to use the other 896 * three for multicast addresses. 897 */ 898 static void tl_setfilt(sc, addr, slot) 899 struct tl_softc *sc; 900 caddr_t addr; 901 int slot; 902 { 903 int i; 904 u_int16_t regaddr; 905 906 regaddr = TL_AREG0_B5 + (slot * ETHER_ADDR_LEN); 907 908 for (i = 0; i < ETHER_ADDR_LEN; i++) 909 tl_dio_write8(sc, regaddr + i, *(addr + i)); 910 911 return; 912 } 913 914 /* 915 * XXX In FreeBSD 3.0, multicast addresses are managed using a doubly 916 * linked list. This is fine, except addresses are added from the head 917 * end of the list. We want to arrange for 224.0.0.1 (the "all hosts") 918 * group to always be in the perfect filter, but as more groups are added, 919 * the 224.0.0.1 entry (which is always added first) gets pushed down 920 * the list and ends up at the tail. So after 3 or 4 multicast groups 921 * are added, the all-hosts entry gets pushed out of the perfect filter 922 * and into the hash table. 923 * 924 * Because the multicast list is a doubly-linked list as opposed to a 925 * circular queue, we don't have the ability to just grab the tail of 926 * the list and traverse it backwards. Instead, we have to traverse 927 * the list once to find the tail, then traverse it again backwards to 928 * update the multicast filter. 929 */ 930 static void tl_setmulti(sc) 931 struct tl_softc *sc; 932 { 933 struct ifnet *ifp; 934 u_int32_t hashes[2] = { 0, 0 }; 935 int h, i; 936 struct ifmultiaddr *ifma; 937 u_int8_t dummy[] = { 0, 0, 0, 0, 0 ,0 }; 938 ifp = &sc->arpcom.ac_if; 939 940 /* First, zot all the existing filters. */ 941 for (i = 1; i < 4; i++) 942 tl_setfilt(sc, (caddr_t)&dummy, i); 943 tl_dio_write32(sc, TL_HASH1, 0); 944 tl_dio_write32(sc, TL_HASH2, 0); 945 946 /* Now program new ones. */ 947 if (ifp->if_flags & IFF_ALLMULTI) { 948 hashes[0] = 0xFFFFFFFF; 949 hashes[1] = 0xFFFFFFFF; 950 } else { 951 i = 1; 952 /* First find the tail of the list. */ 953 for (ifma = ifp->if_multiaddrs.lh_first; ifma != NULL; 954 ifma = ifma->ifma_link.le_next) { 955 if (ifma->ifma_link.le_next == NULL) 956 break; 957 } 958 /* Now traverse the list backwards. */ 959 for (; ifma != NULL && ifma != (void *)&ifp->if_multiaddrs; 960 ifma = (struct ifmultiaddr *)ifma->ifma_link.le_prev) { 961 if (ifma->ifma_addr->sa_family != AF_LINK) 962 continue; 963 /* 964 * Program the first three multicast groups 965 * into the perfect filter. For all others, 966 * use the hash table. 967 */ 968 if (i < 4) { 969 tl_setfilt(sc, 970 LLADDR((struct sockaddr_dl *)ifma->ifma_addr), i); 971 i++; 972 continue; 973 } 974 975 h = tl_calchash( 976 LLADDR((struct sockaddr_dl *)ifma->ifma_addr)); 977 if (h < 32) 978 hashes[0] |= (1 << h); 979 else 980 hashes[1] |= (1 << (h - 32)); 981 } 982 } 983 984 tl_dio_write32(sc, TL_HASH1, hashes[0]); 985 tl_dio_write32(sc, TL_HASH2, hashes[1]); 986 987 return; 988 } 989 990 /* 991 * This routine is recommended by the ThunderLAN manual to insure that 992 * the internal PHY is powered up correctly. It also recommends a one 993 * second pause at the end to 'wait for the clocks to start' but in my 994 * experience this isn't necessary. 995 */ 996 static void tl_hardreset(dev) 997 device_t dev; 998 { 999 struct tl_softc *sc; 1000 int i; 1001 u_int16_t flags; 1002 1003 sc = device_get_softc(dev); 1004 1005 tl_mii_sync(sc); 1006 1007 flags = BMCR_LOOP|BMCR_ISO|BMCR_PDOWN; 1008 1009 for (i = 0; i < MII_NPHY; i++) 1010 tl_miibus_writereg(dev, i, MII_BMCR, flags); 1011 1012 tl_miibus_writereg(dev, 31, MII_BMCR, BMCR_ISO); 1013 DELAY(50000); 1014 tl_miibus_writereg(dev, 31, MII_BMCR, BMCR_LOOP|BMCR_ISO); 1015 tl_mii_sync(sc); 1016 while(tl_miibus_readreg(dev, 31, MII_BMCR) & BMCR_RESET); 1017 1018 DELAY(50000); 1019 return; 1020 } 1021 1022 static void tl_softreset(sc, internal) 1023 struct tl_softc *sc; 1024 int internal; 1025 { 1026 u_int32_t cmd, dummy, i; 1027 1028 /* Assert the adapter reset bit. */ 1029 CMD_SET(sc, TL_CMD_ADRST); 1030 1031 /* Turn off interrupts */ 1032 CMD_SET(sc, TL_CMD_INTSOFF); 1033 1034 /* First, clear the stats registers. */ 1035 for (i = 0; i < 5; i++) 1036 dummy = tl_dio_read32(sc, TL_TXGOODFRAMES); 1037 1038 /* Clear Areg and Hash registers */ 1039 for (i = 0; i < 8; i++) 1040 tl_dio_write32(sc, TL_AREG0_B5, 0x00000000); 1041 1042 /* 1043 * Set up Netconfig register. Enable one channel and 1044 * one fragment mode. 1045 */ 1046 tl_dio_setbit16(sc, TL_NETCONFIG, TL_CFG_ONECHAN|TL_CFG_ONEFRAG); 1047 if (internal && !sc->tl_bitrate) { 1048 tl_dio_setbit16(sc, TL_NETCONFIG, TL_CFG_PHYEN); 1049 } else { 1050 tl_dio_clrbit16(sc, TL_NETCONFIG, TL_CFG_PHYEN); 1051 } 1052 1053 /* Handle cards with bitrate devices. */ 1054 if (sc->tl_bitrate) 1055 tl_dio_setbit16(sc, TL_NETCONFIG, TL_CFG_BITRATE); 1056 1057 /* 1058 * Load adapter irq pacing timer and tx threshold. 1059 * We make the transmit threshold 1 initially but we may 1060 * change that later. 1061 */ 1062 cmd = CSR_READ_4(sc, TL_HOSTCMD); 1063 cmd |= TL_CMD_NES; 1064 cmd &= ~(TL_CMD_RT|TL_CMD_EOC|TL_CMD_ACK_MASK|TL_CMD_CHSEL_MASK); 1065 CMD_PUT(sc, cmd | (TL_CMD_LDTHR | TX_THR)); 1066 CMD_PUT(sc, cmd | (TL_CMD_LDTMR | 0x00000003)); 1067 1068 /* Unreset the MII */ 1069 tl_dio_setbit(sc, TL_NETSIO, TL_SIO_NMRST); 1070 1071 /* Take the adapter out of reset */ 1072 tl_dio_setbit(sc, TL_NETCMD, TL_CMD_NRESET|TL_CMD_NWRAP); 1073 1074 /* Wait for things to settle down a little. */ 1075 DELAY(500); 1076 1077 return; 1078 } 1079 1080 /* 1081 * Probe for a ThunderLAN chip. Check the PCI vendor and device IDs 1082 * against our list and return its name if we find a match. 1083 */ 1084 static int tl_probe(dev) 1085 device_t dev; 1086 { 1087 struct tl_type *t; 1088 1089 t = tl_devs; 1090 1091 while(t->tl_name != NULL) { 1092 if ((pci_get_vendor(dev) == t->tl_vid) && 1093 (pci_get_device(dev) == t->tl_did)) { 1094 device_set_desc(dev, t->tl_name); 1095 return(0); 1096 } 1097 t++; 1098 } 1099 1100 return(ENXIO); 1101 } 1102 1103 static int tl_attach(dev) 1104 device_t dev; 1105 { 1106 int s, i; 1107 u_int32_t command; 1108 u_int16_t did, vid; 1109 struct tl_type *t; 1110 struct ifnet *ifp; 1111 struct tl_softc *sc; 1112 int unit, error = 0, rid; 1113 1114 s = splimp(); 1115 1116 vid = pci_get_vendor(dev); 1117 did = pci_get_device(dev); 1118 sc = device_get_softc(dev); 1119 unit = device_get_unit(dev); 1120 bzero(sc, sizeof(struct tl_softc)); 1121 1122 t = tl_devs; 1123 while(t->tl_name != NULL) { 1124 if (vid == t->tl_vid && did == t->tl_did) 1125 break; 1126 t++; 1127 } 1128 1129 if (t->tl_name == NULL) { 1130 printf("tl%d: unknown device!?\n", unit); 1131 goto fail; 1132 } 1133 1134 /* 1135 * Map control/status registers. 1136 */ 1137 command = pci_read_config(dev, PCIR_COMMAND, 4); 1138 command |= (PCIM_CMD_PORTEN|PCIM_CMD_MEMEN|PCIM_CMD_BUSMASTEREN); 1139 pci_write_config(dev, PCIR_COMMAND, command, 4); 1140 command = pci_read_config(dev, PCIR_COMMAND, 4); 1141 1142 #ifdef TL_USEIOSPACE 1143 if (!(command & PCIM_CMD_PORTEN)) { 1144 printf("tl%d: failed to enable I/O ports!\n", unit); 1145 error = ENXIO; 1146 goto fail; 1147 } 1148 1149 rid = TL_PCI_LOIO; 1150 sc->tl_res = bus_alloc_resource(dev, SYS_RES_IOPORT, &rid, 1151 0, ~0, 1, RF_ACTIVE); 1152 1153 /* 1154 * Some cards have the I/O and memory mapped address registers 1155 * reversed. Try both combinations before giving up. 1156 */ 1157 if (sc->tl_res == NULL) { 1158 rid = TL_PCI_LOMEM; 1159 sc->tl_res = bus_alloc_resource(dev, SYS_RES_IOPORT, &rid, 1160 0, ~0, 1, RF_ACTIVE); 1161 } 1162 #else 1163 if (!(command & PCIM_CMD_MEMEN)) { 1164 printf("tl%d: failed to enable memory mapping!\n", unit); 1165 error = ENXIO; 1166 goto fail; 1167 } 1168 1169 rid = TL_PCI_LOMEM; 1170 sc->tl_res = bus_alloc_resource(dev, SYS_RES_MEMORY, &rid, 1171 0, ~0, 1, RF_ACTIVE); 1172 if (sc->tl_res == NULL) { 1173 rid = TL_PCI_LOIO; 1174 sc->tl_res = bus_alloc_resource(dev, SYS_RES_MEMORY, &rid, 1175 0, ~0, 1, RF_ACTIVE); 1176 } 1177 #endif 1178 1179 if (sc->tl_res == NULL) { 1180 printf("tl%d: couldn't map ports/memory\n", unit); 1181 error = ENXIO; 1182 goto fail; 1183 } 1184 1185 sc->tl_btag = rman_get_bustag(sc->tl_res); 1186 sc->tl_bhandle = rman_get_bushandle(sc->tl_res); 1187 1188 #ifdef notdef 1189 /* 1190 * The ThunderLAN manual suggests jacking the PCI latency 1191 * timer all the way up to its maximum value. I'm not sure 1192 * if this is really necessary, but what the manual wants, 1193 * the manual gets. 1194 */ 1195 command = pci_read_config(dev, TL_PCI_LATENCY_TIMER, 4); 1196 command |= 0x0000FF00; 1197 pci_write_config(dev, TL_PCI_LATENCY_TIMER, command, 4); 1198 #endif 1199 1200 /* Allocate interrupt */ 1201 rid = 0; 1202 sc->tl_irq = bus_alloc_resource(dev, SYS_RES_IRQ, &rid, 0, ~0, 1, 1203 RF_SHAREABLE | RF_ACTIVE); 1204 1205 if (sc->tl_irq == NULL) { 1206 bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res); 1207 printf("tl%d: couldn't map interrupt\n", unit); 1208 error = ENXIO; 1209 goto fail; 1210 } 1211 1212 error = bus_setup_intr(dev, sc->tl_irq, INTR_TYPE_NET, 1213 tl_intr, sc, &sc->tl_intrhand); 1214 1215 if (error) { 1216 bus_release_resource(dev, SYS_RES_IRQ, 0, sc->tl_irq); 1217 bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res); 1218 printf("tl%d: couldn't set up irq\n", unit); 1219 goto fail; 1220 } 1221 1222 /* 1223 * Now allocate memory for the TX and RX lists. 1224 */ 1225 sc->tl_ldata = contigmalloc(sizeof(struct tl_list_data), M_DEVBUF, 1226 M_NOWAIT, 0, 0xffffffff, PAGE_SIZE, 0); 1227 1228 if (sc->tl_ldata == NULL) { 1229 bus_teardown_intr(dev, sc->tl_irq, sc->tl_intrhand); 1230 bus_release_resource(dev, SYS_RES_IRQ, 0, sc->tl_irq); 1231 bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res); 1232 printf("tl%d: no memory for list buffers!\n", unit); 1233 error = ENXIO; 1234 goto fail; 1235 } 1236 1237 bzero(sc->tl_ldata, sizeof(struct tl_list_data)); 1238 1239 sc->tl_unit = unit; 1240 sc->tl_dinfo = t; 1241 if (t->tl_vid == COMPAQ_VENDORID || t->tl_vid == TI_VENDORID) 1242 sc->tl_eeaddr = TL_EEPROM_EADDR; 1243 if (t->tl_vid == OLICOM_VENDORID) 1244 sc->tl_eeaddr = TL_EEPROM_EADDR_OC; 1245 1246 /* Reset the adapter. */ 1247 tl_softreset(sc, 1); 1248 tl_hardreset(dev); 1249 tl_softreset(sc, 1); 1250 1251 /* 1252 * Get station address from the EEPROM. 1253 */ 1254 if (tl_read_eeprom(sc, (caddr_t)&sc->arpcom.ac_enaddr, 1255 sc->tl_eeaddr, ETHER_ADDR_LEN)) { 1256 bus_teardown_intr(dev, sc->tl_irq, sc->tl_intrhand); 1257 bus_release_resource(dev, SYS_RES_IRQ, 0, sc->tl_irq); 1258 bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res); 1259 contigfree(sc->tl_ldata, 1260 sizeof(struct tl_list_data), M_DEVBUF); 1261 printf("tl%d: failed to read station address\n", unit); 1262 error = ENXIO; 1263 goto fail; 1264 } 1265 1266 /* 1267 * XXX Olicom, in its desire to be different from the 1268 * rest of the world, has done strange things with the 1269 * encoding of the station address in the EEPROM. First 1270 * of all, they store the address at offset 0xF8 rather 1271 * than at 0x83 like the ThunderLAN manual suggests. 1272 * Second, they store the address in three 16-bit words in 1273 * network byte order, as opposed to storing it sequentially 1274 * like all the other ThunderLAN cards. In order to get 1275 * the station address in a form that matches what the Olicom 1276 * diagnostic utility specifies, we have to byte-swap each 1277 * word. To make things even more confusing, neither 00:00:28 1278 * nor 00:00:24 appear in the IEEE OUI database. 1279 */ 1280 if (sc->tl_dinfo->tl_vid == OLICOM_VENDORID) { 1281 for (i = 0; i < ETHER_ADDR_LEN; i += 2) { 1282 u_int16_t *p; 1283 p = (u_int16_t *)&sc->arpcom.ac_enaddr[i]; 1284 *p = ntohs(*p); 1285 } 1286 } 1287 1288 /* 1289 * A ThunderLAN chip was detected. Inform the world. 1290 */ 1291 printf("tl%d: Ethernet address: %6D\n", unit, 1292 sc->arpcom.ac_enaddr, ":"); 1293 1294 ifp = &sc->arpcom.ac_if; 1295 ifp->if_softc = sc; 1296 if_initname(ifp, "tl", sc->tl_unit); 1297 ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; 1298 ifp->if_ioctl = tl_ioctl; 1299 ifp->if_output = ether_output; 1300 ifp->if_start = tl_start; 1301 ifp->if_watchdog = tl_watchdog; 1302 ifp->if_init = tl_init; 1303 ifp->if_mtu = ETHERMTU; 1304 ifp->if_snd.ifq_maxlen = TL_TX_LIST_CNT - 1; 1305 callout_handle_init(&sc->tl_stat_ch); 1306 1307 /* Reset the adapter again. */ 1308 tl_softreset(sc, 1); 1309 tl_hardreset(dev); 1310 tl_softreset(sc, 1); 1311 1312 /* 1313 * Do MII setup. If no PHYs are found, then this is a 1314 * bitrate ThunderLAN chip that only supports 10baseT 1315 * and AUI/BNC. 1316 */ 1317 if (mii_phy_probe(dev, &sc->tl_miibus, 1318 tl_ifmedia_upd, tl_ifmedia_sts)) { 1319 struct ifmedia *ifm; 1320 sc->tl_bitrate = 1; 1321 ifmedia_init(&sc->ifmedia, 0, tl_ifmedia_upd, tl_ifmedia_sts); 1322 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T, 0, NULL); 1323 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T|IFM_HDX, 0, NULL); 1324 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T|IFM_FDX, 0, NULL); 1325 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_5, 0, NULL); 1326 ifmedia_set(&sc->ifmedia, IFM_ETHER|IFM_10_T); 1327 /* Reset again, this time setting bitrate mode. */ 1328 tl_softreset(sc, 1); 1329 ifm = &sc->ifmedia; 1330 ifm->ifm_media = ifm->ifm_cur->ifm_media; 1331 tl_ifmedia_upd(ifp); 1332 } 1333 1334 /* 1335 * Call MI attach routine. 1336 */ 1337 ether_ifattach(ifp, sc->arpcom.ac_enaddr); 1338 1339 fail: 1340 splx(s); 1341 return(error); 1342 } 1343 1344 static int tl_detach(dev) 1345 device_t dev; 1346 { 1347 struct tl_softc *sc; 1348 struct ifnet *ifp; 1349 int s; 1350 1351 s = splimp(); 1352 1353 sc = device_get_softc(dev); 1354 ifp = &sc->arpcom.ac_if; 1355 1356 tl_stop(sc); 1357 ether_ifdetach(ifp); 1358 1359 bus_generic_detach(dev); 1360 device_delete_child(dev, sc->tl_miibus); 1361 1362 contigfree(sc->tl_ldata, sizeof(struct tl_list_data), M_DEVBUF); 1363 if (sc->tl_bitrate) 1364 ifmedia_removeall(&sc->ifmedia); 1365 1366 bus_teardown_intr(dev, sc->tl_irq, sc->tl_intrhand); 1367 bus_release_resource(dev, SYS_RES_IRQ, 0, sc->tl_irq); 1368 bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res); 1369 1370 splx(s); 1371 1372 return(0); 1373 } 1374 1375 /* 1376 * Initialize the transmit lists. 1377 */ 1378 static int tl_list_tx_init(sc) 1379 struct tl_softc *sc; 1380 { 1381 struct tl_chain_data *cd; 1382 struct tl_list_data *ld; 1383 int i; 1384 1385 cd = &sc->tl_cdata; 1386 ld = sc->tl_ldata; 1387 for (i = 0; i < TL_TX_LIST_CNT; i++) { 1388 cd->tl_tx_chain[i].tl_ptr = &ld->tl_tx_list[i]; 1389 if (i == (TL_TX_LIST_CNT - 1)) 1390 cd->tl_tx_chain[i].tl_next = NULL; 1391 else 1392 cd->tl_tx_chain[i].tl_next = &cd->tl_tx_chain[i + 1]; 1393 } 1394 1395 cd->tl_tx_free = &cd->tl_tx_chain[0]; 1396 cd->tl_tx_tail = cd->tl_tx_head = NULL; 1397 sc->tl_txeoc = 1; 1398 1399 return(0); 1400 } 1401 1402 /* 1403 * Initialize the RX lists and allocate mbufs for them. 1404 */ 1405 static int tl_list_rx_init(sc) 1406 struct tl_softc *sc; 1407 { 1408 struct tl_chain_data *cd; 1409 struct tl_list_data *ld; 1410 int i; 1411 1412 cd = &sc->tl_cdata; 1413 ld = sc->tl_ldata; 1414 1415 for (i = 0; i < TL_RX_LIST_CNT; i++) { 1416 cd->tl_rx_chain[i].tl_ptr = 1417 (struct tl_list_onefrag *)&ld->tl_rx_list[i]; 1418 if (tl_newbuf(sc, &cd->tl_rx_chain[i]) == ENOBUFS) 1419 return(ENOBUFS); 1420 if (i == (TL_RX_LIST_CNT - 1)) { 1421 cd->tl_rx_chain[i].tl_next = NULL; 1422 ld->tl_rx_list[i].tlist_fptr = 0; 1423 } else { 1424 cd->tl_rx_chain[i].tl_next = &cd->tl_rx_chain[i + 1]; 1425 ld->tl_rx_list[i].tlist_fptr = 1426 vtophys(&ld->tl_rx_list[i + 1]); 1427 } 1428 } 1429 1430 cd->tl_rx_head = &cd->tl_rx_chain[0]; 1431 cd->tl_rx_tail = &cd->tl_rx_chain[TL_RX_LIST_CNT - 1]; 1432 1433 return(0); 1434 } 1435 1436 static int tl_newbuf(sc, c) 1437 struct tl_softc *sc; 1438 struct tl_chain_onefrag *c; 1439 { 1440 struct mbuf *m_new = NULL; 1441 1442 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1443 if (m_new == NULL) 1444 return(ENOBUFS); 1445 1446 MCLGET(m_new, M_DONTWAIT); 1447 if (!(m_new->m_flags & M_EXT)) { 1448 m_freem(m_new); 1449 return(ENOBUFS); 1450 } 1451 1452 #ifdef __alpha__ 1453 m_new->m_data += 2; 1454 #endif 1455 1456 c->tl_mbuf = m_new; 1457 c->tl_next = NULL; 1458 c->tl_ptr->tlist_frsize = MCLBYTES; 1459 c->tl_ptr->tlist_fptr = 0; 1460 c->tl_ptr->tl_frag.tlist_dadr = vtophys(mtod(m_new, caddr_t)); 1461 c->tl_ptr->tl_frag.tlist_dcnt = MCLBYTES; 1462 c->tl_ptr->tlist_cstat = TL_CSTAT_READY; 1463 1464 return(0); 1465 } 1466 /* 1467 * Interrupt handler for RX 'end of frame' condition (EOF). This 1468 * tells us that a full ethernet frame has been captured and we need 1469 * to handle it. 1470 * 1471 * Reception is done using 'lists' which consist of a header and a 1472 * series of 10 data count/data address pairs that point to buffers. 1473 * Initially you're supposed to create a list, populate it with pointers 1474 * to buffers, then load the physical address of the list into the 1475 * ch_parm register. The adapter is then supposed to DMA the received 1476 * frame into the buffers for you. 1477 * 1478 * To make things as fast as possible, we have the chip DMA directly 1479 * into mbufs. This saves us from having to do a buffer copy: we can 1480 * just hand the mbufs directly to ether_input(). Once the frame has 1481 * been sent on its way, the 'list' structure is assigned a new buffer 1482 * and moved to the end of the RX chain. As long we we stay ahead of 1483 * the chip, it will always think it has an endless receive channel. 1484 * 1485 * If we happen to fall behind and the chip manages to fill up all of 1486 * the buffers, it will generate an end of channel interrupt and wait 1487 * for us to empty the chain and restart the receiver. 1488 */ 1489 static int tl_intvec_rxeof(xsc, type) 1490 void *xsc; 1491 u_int32_t type; 1492 { 1493 struct tl_softc *sc; 1494 int r = 0, total_len = 0; 1495 struct ether_header *eh; 1496 struct mbuf *m; 1497 struct ifnet *ifp; 1498 struct tl_chain_onefrag *cur_rx; 1499 1500 sc = xsc; 1501 ifp = &sc->arpcom.ac_if; 1502 1503 while(sc->tl_cdata.tl_rx_head != NULL) { 1504 cur_rx = sc->tl_cdata.tl_rx_head; 1505 if (!(cur_rx->tl_ptr->tlist_cstat & TL_CSTAT_FRAMECMP)) 1506 break; 1507 r++; 1508 sc->tl_cdata.tl_rx_head = cur_rx->tl_next; 1509 m = cur_rx->tl_mbuf; 1510 total_len = cur_rx->tl_ptr->tlist_frsize; 1511 1512 if (tl_newbuf(sc, cur_rx) == ENOBUFS) { 1513 ifp->if_ierrors++; 1514 cur_rx->tl_ptr->tlist_frsize = MCLBYTES; 1515 cur_rx->tl_ptr->tlist_cstat = TL_CSTAT_READY; 1516 cur_rx->tl_ptr->tl_frag.tlist_dcnt = MCLBYTES; 1517 continue; 1518 } 1519 1520 sc->tl_cdata.tl_rx_tail->tl_ptr->tlist_fptr = 1521 vtophys(cur_rx->tl_ptr); 1522 sc->tl_cdata.tl_rx_tail->tl_next = cur_rx; 1523 sc->tl_cdata.tl_rx_tail = cur_rx; 1524 1525 eh = mtod(m, struct ether_header *); 1526 m->m_pkthdr.rcvif = ifp; 1527 1528 /* 1529 * Note: when the ThunderLAN chip is in 'capture all 1530 * frames' mode, it will receive its own transmissions. 1531 * We drop don't need to process our own transmissions, 1532 * so we drop them here and continue. 1533 */ 1534 /*if (ifp->if_flags & IFF_PROMISC && */ 1535 if (!bcmp(eh->ether_shost, sc->arpcom.ac_enaddr, 1536 ETHER_ADDR_LEN)) { 1537 m_freem(m); 1538 continue; 1539 } 1540 1541 /* Remove header from mbuf and pass it on. */ 1542 m->m_pkthdr.len = m->m_len = 1543 total_len - sizeof(struct ether_header); 1544 m->m_data += sizeof(struct ether_header); 1545 ether_input(ifp, eh, m); 1546 } 1547 1548 return(r); 1549 } 1550 1551 /* 1552 * The RX-EOC condition hits when the ch_parm address hasn't been 1553 * initialized or the adapter reached a list with a forward pointer 1554 * of 0 (which indicates the end of the chain). In our case, this means 1555 * the card has hit the end of the receive buffer chain and we need to 1556 * empty out the buffers and shift the pointer back to the beginning again. 1557 */ 1558 static int tl_intvec_rxeoc(xsc, type) 1559 void *xsc; 1560 u_int32_t type; 1561 { 1562 struct tl_softc *sc; 1563 int r; 1564 struct tl_chain_data *cd; 1565 1566 1567 sc = xsc; 1568 cd = &sc->tl_cdata; 1569 1570 /* Flush out the receive queue and ack RXEOF interrupts. */ 1571 r = tl_intvec_rxeof(xsc, type); 1572 CMD_PUT(sc, TL_CMD_ACK | r | (type & ~(0x00100000))); 1573 r = 1; 1574 cd->tl_rx_head = &cd->tl_rx_chain[0]; 1575 cd->tl_rx_tail = &cd->tl_rx_chain[TL_RX_LIST_CNT - 1]; 1576 CSR_WRITE_4(sc, TL_CH_PARM, vtophys(sc->tl_cdata.tl_rx_head->tl_ptr)); 1577 r |= (TL_CMD_GO|TL_CMD_RT); 1578 return(r); 1579 } 1580 1581 static int tl_intvec_txeof(xsc, type) 1582 void *xsc; 1583 u_int32_t type; 1584 { 1585 struct tl_softc *sc; 1586 int r = 0; 1587 struct tl_chain *cur_tx; 1588 1589 sc = xsc; 1590 1591 /* 1592 * Go through our tx list and free mbufs for those 1593 * frames that have been sent. 1594 */ 1595 while (sc->tl_cdata.tl_tx_head != NULL) { 1596 cur_tx = sc->tl_cdata.tl_tx_head; 1597 if (!(cur_tx->tl_ptr->tlist_cstat & TL_CSTAT_FRAMECMP)) 1598 break; 1599 sc->tl_cdata.tl_tx_head = cur_tx->tl_next; 1600 1601 r++; 1602 m_freem(cur_tx->tl_mbuf); 1603 cur_tx->tl_mbuf = NULL; 1604 1605 cur_tx->tl_next = sc->tl_cdata.tl_tx_free; 1606 sc->tl_cdata.tl_tx_free = cur_tx; 1607 if (!cur_tx->tl_ptr->tlist_fptr) 1608 break; 1609 } 1610 1611 return(r); 1612 } 1613 1614 /* 1615 * The transmit end of channel interrupt. The adapter triggers this 1616 * interrupt to tell us it hit the end of the current transmit list. 1617 * 1618 * A note about this: it's possible for a condition to arise where 1619 * tl_start() may try to send frames between TXEOF and TXEOC interrupts. 1620 * You have to avoid this since the chip expects things to go in a 1621 * particular order: transmit, acknowledge TXEOF, acknowledge TXEOC. 1622 * When the TXEOF handler is called, it will free all of the transmitted 1623 * frames and reset the tx_head pointer to NULL. However, a TXEOC 1624 * interrupt should be received and acknowledged before any more frames 1625 * are queued for transmission. If tl_statrt() is called after TXEOF 1626 * resets the tx_head pointer but _before_ the TXEOC interrupt arrives, 1627 * it could attempt to issue a transmit command prematurely. 1628 * 1629 * To guard against this, tl_start() will only issue transmit commands 1630 * if the tl_txeoc flag is set, and only the TXEOC interrupt handler 1631 * can set this flag once tl_start() has cleared it. 1632 */ 1633 static int tl_intvec_txeoc(xsc, type) 1634 void *xsc; 1635 u_int32_t type; 1636 { 1637 struct tl_softc *sc; 1638 struct ifnet *ifp; 1639 u_int32_t cmd; 1640 1641 sc = xsc; 1642 ifp = &sc->arpcom.ac_if; 1643 1644 /* Clear the timeout timer. */ 1645 ifp->if_timer = 0; 1646 1647 if (sc->tl_cdata.tl_tx_head == NULL) { 1648 ifp->if_flags &= ~IFF_OACTIVE; 1649 sc->tl_cdata.tl_tx_tail = NULL; 1650 sc->tl_txeoc = 1; 1651 } else { 1652 sc->tl_txeoc = 0; 1653 /* First we have to ack the EOC interrupt. */ 1654 CMD_PUT(sc, TL_CMD_ACK | 0x00000001 | type); 1655 /* Then load the address of the next TX list. */ 1656 CSR_WRITE_4(sc, TL_CH_PARM, 1657 vtophys(sc->tl_cdata.tl_tx_head->tl_ptr)); 1658 /* Restart TX channel. */ 1659 cmd = CSR_READ_4(sc, TL_HOSTCMD); 1660 cmd &= ~TL_CMD_RT; 1661 cmd |= TL_CMD_GO|TL_CMD_INTSON; 1662 CMD_PUT(sc, cmd); 1663 return(0); 1664 } 1665 1666 return(1); 1667 } 1668 1669 static int tl_intvec_adchk(xsc, type) 1670 void *xsc; 1671 u_int32_t type; 1672 { 1673 struct tl_softc *sc; 1674 1675 sc = xsc; 1676 1677 if (type) 1678 printf("tl%d: adapter check: %x\n", sc->tl_unit, 1679 (unsigned int)CSR_READ_4(sc, TL_CH_PARM)); 1680 1681 tl_softreset(sc, 1); 1682 tl_stop(sc); 1683 tl_init(sc); 1684 CMD_SET(sc, TL_CMD_INTSON); 1685 1686 return(0); 1687 } 1688 1689 static int tl_intvec_netsts(xsc, type) 1690 void *xsc; 1691 u_int32_t type; 1692 { 1693 struct tl_softc *sc; 1694 u_int16_t netsts; 1695 1696 sc = xsc; 1697 1698 netsts = tl_dio_read16(sc, TL_NETSTS); 1699 tl_dio_write16(sc, TL_NETSTS, netsts); 1700 1701 printf("tl%d: network status: %x\n", sc->tl_unit, netsts); 1702 1703 return(1); 1704 } 1705 1706 static void tl_intr(xsc) 1707 void *xsc; 1708 { 1709 struct tl_softc *sc; 1710 struct ifnet *ifp; 1711 int r = 0; 1712 u_int32_t type = 0; 1713 u_int16_t ints = 0; 1714 u_int8_t ivec = 0; 1715 1716 sc = xsc; 1717 1718 /* Disable interrupts */ 1719 ints = CSR_READ_2(sc, TL_HOST_INT); 1720 CSR_WRITE_2(sc, TL_HOST_INT, ints); 1721 type = (ints << 16) & 0xFFFF0000; 1722 ivec = (ints & TL_VEC_MASK) >> 5; 1723 ints = (ints & TL_INT_MASK) >> 2; 1724 1725 ifp = &sc->arpcom.ac_if; 1726 1727 switch(ints) { 1728 case (TL_INTR_INVALID): 1729 #ifdef DIAGNOSTIC 1730 printf("tl%d: got an invalid interrupt!\n", sc->tl_unit); 1731 #endif 1732 /* Re-enable interrupts but don't ack this one. */ 1733 CMD_PUT(sc, type); 1734 r = 0; 1735 break; 1736 case (TL_INTR_TXEOF): 1737 r = tl_intvec_txeof((void *)sc, type); 1738 break; 1739 case (TL_INTR_TXEOC): 1740 r = tl_intvec_txeoc((void *)sc, type); 1741 break; 1742 case (TL_INTR_STATOFLOW): 1743 tl_stats_update(sc); 1744 r = 1; 1745 break; 1746 case (TL_INTR_RXEOF): 1747 r = tl_intvec_rxeof((void *)sc, type); 1748 break; 1749 case (TL_INTR_DUMMY): 1750 printf("tl%d: got a dummy interrupt\n", sc->tl_unit); 1751 r = 1; 1752 break; 1753 case (TL_INTR_ADCHK): 1754 if (ivec) 1755 r = tl_intvec_adchk((void *)sc, type); 1756 else 1757 r = tl_intvec_netsts((void *)sc, type); 1758 break; 1759 case (TL_INTR_RXEOC): 1760 r = tl_intvec_rxeoc((void *)sc, type); 1761 break; 1762 default: 1763 printf("%s: bogus interrupt type\n", ifp->if_xname); 1764 break; 1765 } 1766 1767 /* Re-enable interrupts */ 1768 if (r) { 1769 CMD_PUT(sc, TL_CMD_ACK | r | type); 1770 } 1771 1772 if (ifp->if_snd.ifq_head != NULL) 1773 tl_start(ifp); 1774 1775 return; 1776 } 1777 1778 static void tl_stats_update(xsc) 1779 void *xsc; 1780 { 1781 struct tl_softc *sc; 1782 struct ifnet *ifp; 1783 struct tl_stats tl_stats; 1784 struct mii_data *mii; 1785 u_int32_t *p; 1786 int s; 1787 1788 s = splimp(); 1789 1790 bzero((char *)&tl_stats, sizeof(struct tl_stats)); 1791 1792 sc = xsc; 1793 ifp = &sc->arpcom.ac_if; 1794 1795 p = (u_int32_t *)&tl_stats; 1796 1797 CSR_WRITE_2(sc, TL_DIO_ADDR, TL_TXGOODFRAMES|TL_DIO_ADDR_INC); 1798 *p++ = CSR_READ_4(sc, TL_DIO_DATA); 1799 *p++ = CSR_READ_4(sc, TL_DIO_DATA); 1800 *p++ = CSR_READ_4(sc, TL_DIO_DATA); 1801 *p++ = CSR_READ_4(sc, TL_DIO_DATA); 1802 *p++ = CSR_READ_4(sc, TL_DIO_DATA); 1803 1804 ifp->if_opackets += tl_tx_goodframes(tl_stats); 1805 ifp->if_collisions += tl_stats.tl_tx_single_collision + 1806 tl_stats.tl_tx_multi_collision; 1807 ifp->if_ipackets += tl_rx_goodframes(tl_stats); 1808 ifp->if_ierrors += tl_stats.tl_crc_errors + tl_stats.tl_code_errors + 1809 tl_rx_overrun(tl_stats); 1810 ifp->if_oerrors += tl_tx_underrun(tl_stats); 1811 1812 if (tl_tx_underrun(tl_stats)) { 1813 u_int8_t tx_thresh; 1814 tx_thresh = tl_dio_read8(sc, TL_ACOMMIT) & TL_AC_TXTHRESH; 1815 if (tx_thresh != TL_AC_TXTHRESH_WHOLEPKT) { 1816 tx_thresh >>= 4; 1817 tx_thresh++; 1818 printf("tl%d: tx underrun -- increasing " 1819 "tx threshold to %d bytes\n", sc->tl_unit, 1820 (64 * (tx_thresh * 4))); 1821 tl_dio_clrbit(sc, TL_ACOMMIT, TL_AC_TXTHRESH); 1822 tl_dio_setbit(sc, TL_ACOMMIT, tx_thresh << 4); 1823 } 1824 } 1825 1826 sc->tl_stat_ch = timeout(tl_stats_update, sc, hz); 1827 1828 if (!sc->tl_bitrate) { 1829 mii = device_get_softc(sc->tl_miibus); 1830 mii_tick(mii); 1831 } 1832 1833 splx(s); 1834 1835 return; 1836 } 1837 1838 /* 1839 * Encapsulate an mbuf chain in a list by coupling the mbuf data 1840 * pointers to the fragment pointers. 1841 */ 1842 static int tl_encap(sc, c, m_head) 1843 struct tl_softc *sc; 1844 struct tl_chain *c; 1845 struct mbuf *m_head; 1846 { 1847 int frag = 0; 1848 struct tl_frag *f = NULL; 1849 int total_len; 1850 struct mbuf *m; 1851 1852 /* 1853 * Start packing the mbufs in this chain into 1854 * the fragment pointers. Stop when we run out 1855 * of fragments or hit the end of the mbuf chain. 1856 */ 1857 m = m_head; 1858 total_len = 0; 1859 1860 for (m = m_head, frag = 0; m != NULL; m = m->m_next) { 1861 if (m->m_len != 0) { 1862 if (frag == TL_MAXFRAGS) 1863 break; 1864 total_len+= m->m_len; 1865 c->tl_ptr->tl_frag[frag].tlist_dadr = 1866 vtophys(mtod(m, vm_offset_t)); 1867 c->tl_ptr->tl_frag[frag].tlist_dcnt = m->m_len; 1868 frag++; 1869 } 1870 } 1871 1872 /* 1873 * Handle special cases. 1874 * Special case #1: we used up all 10 fragments, but 1875 * we have more mbufs left in the chain. Copy the 1876 * data into an mbuf cluster. Note that we don't 1877 * bother clearing the values in the other fragment 1878 * pointers/counters; it wouldn't gain us anything, 1879 * and would waste cycles. 1880 */ 1881 if (m != NULL) { 1882 struct mbuf *m_new = NULL; 1883 1884 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1885 if (m_new == NULL) { 1886 printf("tl%d: no memory for tx list\n", sc->tl_unit); 1887 return(1); 1888 } 1889 if (m_head->m_pkthdr.len > MHLEN) { 1890 MCLGET(m_new, M_DONTWAIT); 1891 if (!(m_new->m_flags & M_EXT)) { 1892 m_freem(m_new); 1893 printf("tl%d: no memory for tx list\n", 1894 sc->tl_unit); 1895 return(1); 1896 } 1897 } 1898 m_copydata(m_head, 0, m_head->m_pkthdr.len, 1899 mtod(m_new, caddr_t)); 1900 m_new->m_pkthdr.len = m_new->m_len = m_head->m_pkthdr.len; 1901 m_freem(m_head); 1902 m_head = m_new; 1903 f = &c->tl_ptr->tl_frag[0]; 1904 f->tlist_dadr = vtophys(mtod(m_new, caddr_t)); 1905 f->tlist_dcnt = total_len = m_new->m_len; 1906 frag = 1; 1907 } 1908 1909 /* 1910 * Special case #2: the frame is smaller than the minimum 1911 * frame size. We have to pad it to make the chip happy. 1912 */ 1913 if (total_len < TL_MIN_FRAMELEN) { 1914 if (frag == TL_MAXFRAGS) 1915 printf("tl%d: all frags filled but " 1916 "frame still to small!\n", sc->tl_unit); 1917 f = &c->tl_ptr->tl_frag[frag]; 1918 f->tlist_dcnt = TL_MIN_FRAMELEN - total_len; 1919 f->tlist_dadr = vtophys(&sc->tl_ldata->tl_pad); 1920 total_len += f->tlist_dcnt; 1921 frag++; 1922 } 1923 1924 c->tl_mbuf = m_head; 1925 c->tl_ptr->tl_frag[frag - 1].tlist_dcnt |= TL_LAST_FRAG; 1926 c->tl_ptr->tlist_frsize = total_len; 1927 c->tl_ptr->tlist_cstat = TL_CSTAT_READY; 1928 c->tl_ptr->tlist_fptr = 0; 1929 1930 return(0); 1931 } 1932 1933 /* 1934 * Main transmit routine. To avoid having to do mbuf copies, we put pointers 1935 * to the mbuf data regions directly in the transmit lists. We also save a 1936 * copy of the pointers since the transmit list fragment pointers are 1937 * physical addresses. 1938 */ 1939 static void tl_start(ifp) 1940 struct ifnet *ifp; 1941 { 1942 struct tl_softc *sc; 1943 struct mbuf *m_head = NULL; 1944 u_int32_t cmd; 1945 struct tl_chain *prev = NULL, *cur_tx = NULL, *start_tx; 1946 1947 sc = ifp->if_softc; 1948 1949 /* 1950 * Check for an available queue slot. If there are none, 1951 * punt. 1952 */ 1953 if (sc->tl_cdata.tl_tx_free == NULL) { 1954 ifp->if_flags |= IFF_OACTIVE; 1955 return; 1956 } 1957 1958 start_tx = sc->tl_cdata.tl_tx_free; 1959 1960 while(sc->tl_cdata.tl_tx_free != NULL) { 1961 IF_DEQUEUE(&ifp->if_snd, m_head); 1962 if (m_head == NULL) 1963 break; 1964 1965 /* Pick a chain member off the free list. */ 1966 cur_tx = sc->tl_cdata.tl_tx_free; 1967 sc->tl_cdata.tl_tx_free = cur_tx->tl_next; 1968 1969 cur_tx->tl_next = NULL; 1970 1971 /* Pack the data into the list. */ 1972 tl_encap(sc, cur_tx, m_head); 1973 1974 /* Chain it together */ 1975 if (prev != NULL) { 1976 prev->tl_next = cur_tx; 1977 prev->tl_ptr->tlist_fptr = vtophys(cur_tx->tl_ptr); 1978 } 1979 prev = cur_tx; 1980 1981 /* 1982 * If there's a BPF listener, bounce a copy of this frame 1983 * to him. 1984 */ 1985 if (ifp->if_bpf) 1986 bpf_mtap(ifp, cur_tx->tl_mbuf); 1987 } 1988 1989 /* 1990 * If there are no packets queued, bail. 1991 */ 1992 if (cur_tx == NULL) 1993 return; 1994 1995 /* 1996 * That's all we can stands, we can't stands no more. 1997 * If there are no other transfers pending, then issue the 1998 * TX GO command to the adapter to start things moving. 1999 * Otherwise, just leave the data in the queue and let 2000 * the EOF/EOC interrupt handler send. 2001 */ 2002 if (sc->tl_cdata.tl_tx_head == NULL) { 2003 sc->tl_cdata.tl_tx_head = start_tx; 2004 sc->tl_cdata.tl_tx_tail = cur_tx; 2005 2006 if (sc->tl_txeoc) { 2007 sc->tl_txeoc = 0; 2008 CSR_WRITE_4(sc, TL_CH_PARM, vtophys(start_tx->tl_ptr)); 2009 cmd = CSR_READ_4(sc, TL_HOSTCMD); 2010 cmd &= ~TL_CMD_RT; 2011 cmd |= TL_CMD_GO|TL_CMD_INTSON; 2012 CMD_PUT(sc, cmd); 2013 } 2014 } else { 2015 sc->tl_cdata.tl_tx_tail->tl_next = start_tx; 2016 sc->tl_cdata.tl_tx_tail = cur_tx; 2017 } 2018 2019 /* 2020 * Set a timeout in case the chip goes out to lunch. 2021 */ 2022 ifp->if_timer = 5; 2023 2024 return; 2025 } 2026 2027 static void tl_init(xsc) 2028 void *xsc; 2029 { 2030 struct tl_softc *sc = xsc; 2031 struct ifnet *ifp = &sc->arpcom.ac_if; 2032 int s; 2033 struct mii_data *mii; 2034 2035 s = splimp(); 2036 2037 ifp = &sc->arpcom.ac_if; 2038 2039 /* 2040 * Cancel pending I/O. 2041 */ 2042 tl_stop(sc); 2043 2044 /* Initialize TX FIFO threshold */ 2045 tl_dio_clrbit(sc, TL_ACOMMIT, TL_AC_TXTHRESH); 2046 tl_dio_setbit(sc, TL_ACOMMIT, TL_AC_TXTHRESH_16LONG); 2047 2048 /* Set PCI burst size */ 2049 tl_dio_write8(sc, TL_BSIZEREG, TL_RXBURST_16LONG|TL_TXBURST_16LONG); 2050 2051 /* 2052 * Set 'capture all frames' bit for promiscuous mode. 2053 */ 2054 if (ifp->if_flags & IFF_PROMISC) 2055 tl_dio_setbit(sc, TL_NETCMD, TL_CMD_CAF); 2056 else 2057 tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_CAF); 2058 2059 /* 2060 * Set capture broadcast bit to capture broadcast frames. 2061 */ 2062 if (ifp->if_flags & IFF_BROADCAST) 2063 tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_NOBRX); 2064 else 2065 tl_dio_setbit(sc, TL_NETCMD, TL_CMD_NOBRX); 2066 2067 tl_dio_write16(sc, TL_MAXRX, MCLBYTES); 2068 2069 /* Init our MAC address */ 2070 tl_setfilt(sc, (caddr_t)&sc->arpcom.ac_enaddr, 0); 2071 2072 /* Init multicast filter, if needed. */ 2073 tl_setmulti(sc); 2074 2075 /* Init circular RX list. */ 2076 if (tl_list_rx_init(sc) == ENOBUFS) { 2077 printf("tl%d: initialization failed: no " 2078 "memory for rx buffers\n", sc->tl_unit); 2079 tl_stop(sc); 2080 return; 2081 } 2082 2083 /* Init TX pointers. */ 2084 tl_list_tx_init(sc); 2085 2086 /* Enable PCI interrupts. */ 2087 CMD_SET(sc, TL_CMD_INTSON); 2088 2089 /* Load the address of the rx list */ 2090 CMD_SET(sc, TL_CMD_RT); 2091 CSR_WRITE_4(sc, TL_CH_PARM, vtophys(&sc->tl_ldata->tl_rx_list[0])); 2092 2093 if (!sc->tl_bitrate) { 2094 if (sc->tl_miibus != NULL) { 2095 mii = device_get_softc(sc->tl_miibus); 2096 mii_mediachg(mii); 2097 } 2098 } 2099 2100 /* Send the RX go command */ 2101 CMD_SET(sc, TL_CMD_GO|TL_CMD_NES|TL_CMD_RT); 2102 2103 ifp->if_flags |= IFF_RUNNING; 2104 ifp->if_flags &= ~IFF_OACTIVE; 2105 2106 (void)splx(s); 2107 2108 /* Start the stats update counter */ 2109 sc->tl_stat_ch = timeout(tl_stats_update, sc, hz); 2110 2111 return; 2112 } 2113 2114 /* 2115 * Set media options. 2116 */ 2117 static int tl_ifmedia_upd(ifp) 2118 struct ifnet *ifp; 2119 { 2120 struct tl_softc *sc; 2121 struct mii_data *mii = NULL; 2122 2123 sc = ifp->if_softc; 2124 2125 if (sc->tl_bitrate) 2126 tl_setmode(sc, sc->ifmedia.ifm_media); 2127 else { 2128 mii = device_get_softc(sc->tl_miibus); 2129 mii_mediachg(mii); 2130 } 2131 2132 return(0); 2133 } 2134 2135 /* 2136 * Report current media status. 2137 */ 2138 static void tl_ifmedia_sts(ifp, ifmr) 2139 struct ifnet *ifp; 2140 struct ifmediareq *ifmr; 2141 { 2142 struct tl_softc *sc; 2143 struct mii_data *mii; 2144 2145 sc = ifp->if_softc; 2146 2147 ifmr->ifm_active = IFM_ETHER; 2148 2149 if (sc->tl_bitrate) { 2150 if (tl_dio_read8(sc, TL_ACOMMIT) & TL_AC_MTXD1) 2151 ifmr->ifm_active = IFM_ETHER|IFM_10_5; 2152 else 2153 ifmr->ifm_active = IFM_ETHER|IFM_10_T; 2154 if (tl_dio_read8(sc, TL_ACOMMIT) & TL_AC_MTXD3) 2155 ifmr->ifm_active |= IFM_HDX; 2156 else 2157 ifmr->ifm_active |= IFM_FDX; 2158 return; 2159 } else { 2160 mii = device_get_softc(sc->tl_miibus); 2161 mii_pollstat(mii); 2162 ifmr->ifm_active = mii->mii_media_active; 2163 ifmr->ifm_status = mii->mii_media_status; 2164 } 2165 2166 return; 2167 } 2168 2169 static int tl_ioctl(ifp, command, data, cr) 2170 struct ifnet *ifp; 2171 u_long command; 2172 caddr_t data; 2173 struct ucred *cr; 2174 { 2175 struct tl_softc *sc = ifp->if_softc; 2176 struct ifreq *ifr = (struct ifreq *) data; 2177 int s, error = 0; 2178 2179 s = splimp(); 2180 2181 switch(command) { 2182 case SIOCSIFADDR: 2183 case SIOCGIFADDR: 2184 case SIOCSIFMTU: 2185 error = ether_ioctl(ifp, command, data); 2186 break; 2187 case SIOCSIFFLAGS: 2188 if (ifp->if_flags & IFF_UP) { 2189 if (ifp->if_flags & IFF_RUNNING && 2190 ifp->if_flags & IFF_PROMISC && 2191 !(sc->tl_if_flags & IFF_PROMISC)) { 2192 tl_dio_setbit(sc, TL_NETCMD, TL_CMD_CAF); 2193 tl_setmulti(sc); 2194 } else if (ifp->if_flags & IFF_RUNNING && 2195 !(ifp->if_flags & IFF_PROMISC) && 2196 sc->tl_if_flags & IFF_PROMISC) { 2197 tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_CAF); 2198 tl_setmulti(sc); 2199 } else 2200 tl_init(sc); 2201 } else { 2202 if (ifp->if_flags & IFF_RUNNING) { 2203 tl_stop(sc); 2204 } 2205 } 2206 sc->tl_if_flags = ifp->if_flags; 2207 error = 0; 2208 break; 2209 case SIOCADDMULTI: 2210 case SIOCDELMULTI: 2211 tl_setmulti(sc); 2212 error = 0; 2213 break; 2214 case SIOCSIFMEDIA: 2215 case SIOCGIFMEDIA: 2216 if (sc->tl_bitrate) 2217 error = ifmedia_ioctl(ifp, ifr, &sc->ifmedia, command); 2218 else { 2219 struct mii_data *mii; 2220 mii = device_get_softc(sc->tl_miibus); 2221 error = ifmedia_ioctl(ifp, ifr, 2222 &mii->mii_media, command); 2223 } 2224 break; 2225 default: 2226 error = EINVAL; 2227 break; 2228 } 2229 2230 (void)splx(s); 2231 2232 return(error); 2233 } 2234 2235 static void tl_watchdog(ifp) 2236 struct ifnet *ifp; 2237 { 2238 struct tl_softc *sc; 2239 2240 sc = ifp->if_softc; 2241 2242 printf("tl%d: device timeout\n", sc->tl_unit); 2243 2244 ifp->if_oerrors++; 2245 2246 tl_softreset(sc, 1); 2247 tl_init(sc); 2248 2249 return; 2250 } 2251 2252 /* 2253 * Stop the adapter and free any mbufs allocated to the 2254 * RX and TX lists. 2255 */ 2256 static void tl_stop(sc) 2257 struct tl_softc *sc; 2258 { 2259 int i; 2260 struct ifnet *ifp; 2261 2262 ifp = &sc->arpcom.ac_if; 2263 2264 /* Stop the stats updater. */ 2265 untimeout(tl_stats_update, sc, sc->tl_stat_ch); 2266 2267 /* Stop the transmitter */ 2268 CMD_CLR(sc, TL_CMD_RT); 2269 CMD_SET(sc, TL_CMD_STOP); 2270 CSR_WRITE_4(sc, TL_CH_PARM, 0); 2271 2272 /* Stop the receiver */ 2273 CMD_SET(sc, TL_CMD_RT); 2274 CMD_SET(sc, TL_CMD_STOP); 2275 CSR_WRITE_4(sc, TL_CH_PARM, 0); 2276 2277 /* 2278 * Disable host interrupts. 2279 */ 2280 CMD_SET(sc, TL_CMD_INTSOFF); 2281 2282 /* 2283 * Clear list pointer. 2284 */ 2285 CSR_WRITE_4(sc, TL_CH_PARM, 0); 2286 2287 /* 2288 * Free the RX lists. 2289 */ 2290 for (i = 0; i < TL_RX_LIST_CNT; i++) { 2291 if (sc->tl_cdata.tl_rx_chain[i].tl_mbuf != NULL) { 2292 m_freem(sc->tl_cdata.tl_rx_chain[i].tl_mbuf); 2293 sc->tl_cdata.tl_rx_chain[i].tl_mbuf = NULL; 2294 } 2295 } 2296 bzero((char *)&sc->tl_ldata->tl_rx_list, 2297 sizeof(sc->tl_ldata->tl_rx_list)); 2298 2299 /* 2300 * Free the TX list buffers. 2301 */ 2302 for (i = 0; i < TL_TX_LIST_CNT; i++) { 2303 if (sc->tl_cdata.tl_tx_chain[i].tl_mbuf != NULL) { 2304 m_freem(sc->tl_cdata.tl_tx_chain[i].tl_mbuf); 2305 sc->tl_cdata.tl_tx_chain[i].tl_mbuf = NULL; 2306 } 2307 } 2308 bzero((char *)&sc->tl_ldata->tl_tx_list, 2309 sizeof(sc->tl_ldata->tl_tx_list)); 2310 2311 ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE); 2312 2313 return; 2314 } 2315 2316 /* 2317 * Stop all chip I/O so that the kernel's probe routines don't 2318 * get confused by errant DMAs when rebooting. 2319 */ 2320 static void tl_shutdown(dev) 2321 device_t dev; 2322 { 2323 struct tl_softc *sc; 2324 2325 sc = device_get_softc(dev); 2326 2327 tl_stop(sc); 2328 2329 return; 2330 } 2331