1# $FreeBSD$ 2 3PROG?= boot0 4STRIP= 5BINMODE=${NOBINMODE} 6SRCS= ${PROG}.S 7 8# Additional options that you can specify with make OPTS="..." 9# (these only apply to boot0.S) 10# 11# -DVOLUME_SERIAL support volume serial number (NT, XP, Vista) 12# -DSIO do I/O using COM1: 13# -DPXE fallback to INT18/PXE with F6 14# -DCHECK_DRIVE enable checking drive number 15# -DONLY_F_KEYS accept only Fx keys in console 16# -DTEST print drive number on entry 17# 18OPTS ?= -DVOLUME_SERIAL -DPXE 19CFLAGS += ${OPTS} 20 21# Flags used in the boot0.S code: 22# 0x0f all valid partitions enabled. 23# 0x80 'packet', use BIOS EDD (LBA) extensions instead of CHS 24# to read from disk. boot0.S does not check that the extensions 25# are supported, but all modern BIOSes should have them. 26# 0x40 'noupdate', disable writing boot0 back to disk so that 27# the current selection is not preserved across reboots. 28# 0x20 'setdrv', override the drive number supplied by the bios 29# with the one in the boot sector. 30 31# Default boot flags: 32BOOT_BOOT0_FLAGS?= 0x8f 33 34# The number of timer ticks to wait for a keypress before assuming the default 35# selection. Since there are 18.2 ticks per second, the default value of 36# 0xb6 (182d) corresponds to 10 seconds. 37BOOT_BOOT0_TICKS?= 0xb6 38 39# The base address that we the boot0 code to to run it. Don't change this 40# unless you are glutton for punishment. 41BOOT_BOOT0_ORG?= 0x600 42ORG=${BOOT_BOOT0_ORG} 43 44# Comm settings for boot0sio. 45# 46# boot0sio uses BIOS INT $0x14 for serial ports, we can only support these 47# baudrates due to INT14's limited interface. In addition, if 48# BOOT_BOOT0_COMCONSOLE_SPEED=0, then the baud rate and frame format will remain 49# unchanged. Some BIOSes initialize the serial ports to 115200, and this may 50# allow boot0sio access at that rate if so. 51# 52# Bit(s) Description 53# 7-5 data rate (110,150,300,600,1200,2400,4800,9600 bps) 54# 4-3 parity (00 or 10 = none, 01 = odd, 11 = even) 55# 2 stop bits (set = 2, clear = 1) 56# 1-0 data bits (00 = 5, 01 = 6, 10 = 7, 11 = 8) 57.if !defined(BOOT_BOOT0_COMCONSOLE_SPEED) 58BOOT_COMCONSOLE_SPEED?= 9600 59.if ${BOOT_COMCONSOLE_SPEED} == 9600 60BOOT_BOOT0_COMCONSOLE_SPEED= "7 << 5 + 3" 61.elif ${BOOT_COMCONSOLE_SPEED} == 4800 62BOOT_BOOT0_COMCONSOLE_SPEED= "6 << 5 + 3" 63.elif ${BOOT_COMCONSOLE_SPEED} == 2400 64BOOT_BOOT0_COMCONSOLE_SPEED= "5 << 5 + 3" 65.elif ${BOOT_COMCONSOLE_SPEED} == 1200 66BOOT_BOOT0_COMCONSOLE_SPEED= "4 << 5 + 3" 67.elif ${BOOT_COMCONSOLE_SPEED} == 600 68BOOT_BOOT0_COMCONSOLE_SPEED= "3 << 5 + 3" 69.elif ${BOOT_COMCONSOLE_SPEED} == 300 70BOOT_BOOT0_COMCONSOLE_SPEED= "2 << 5 + 3" 71.elif ${BOOT_COMCONSOLE_SPEED} == 150 72BOOT_BOOT0_COMCONSOLE_SPEED= "1 << 5 + 3" 73.elif ${BOOT_COMCONSOLE_SPEED} == 110 74BOOT_BOOT0_COMCONSOLE_SPEED= "0 << 5 + 3" 75.else 76BOOT_BOOT0_COMCONSOLE_SPEED= "7 << 5 + 3" 77.endif 78.endif 79 80CFLAGS+=-DFLAGS=${BOOT_BOOT0_FLAGS} \ 81 -DTICKS=${BOOT_BOOT0_TICKS} \ 82 -DCOMSPEED=${BOOT_BOOT0_COMCONSOLE_SPEED} 83 84LDFLAGS+=${LDFLAGS_BIN} 85 86.include <bsd.prog.mk> 87