1* Freescale enhanced Direct Memory Access(eDMA) Controller
2
3  The eDMA channels have multiplex capability by programmble memory-mapped
4registers. channels are split into two groups, called DMAMUX0 and DMAMUX1,
5specific DMA request source can only be multiplexed by any channel of certain
6group, DMAMUX0 or DMAMUX1, but not both.
7
8* eDMA Controller
9Required properties:
10- compatible :
11	- "fsl,vf610-edma" for eDMA used similar to that on Vybrid vf610 SoC
12	- "fsl,imx7ulp-edma" for eDMA2 used similar to that on i.mx7ulp
13	- "fsl,ls1028a-edma" followed by "fsl,vf610-edma" for eDMA used on the
14	  LS1028A SoC.
15- reg : Specifies base physical address(s) and size of the eDMA registers.
16	The 1st region is eDMA control register's address and size.
17	The 2nd and the 3rd regions are programmable channel multiplexing
18	control register's address and size.
19- interrupts : A list of interrupt-specifiers, one for each entry in
20	interrupt-names on vf610 similar SoC. But for i.mx7ulp per channel
21	per transmission interrupt, total 16 channel interrupt and 1
22	error interrupt(located in the last), no interrupt-names list on
23	i.mx7ulp for clean on dts.
24- #dma-cells : Must be <2>.
25	The 1st cell specifies the DMAMUX(0 for DMAMUX0 and 1 for DMAMUX1).
26	Specific request source can only be multiplexed by specific channels
27	group called DMAMUX.
28	The 2nd cell specifies the request source(slot) ID.
29	See the SoC's reference manual for all the supported request sources.
30- dma-channels : Number of channels supported by the controller
31- clock-names : A list of channel group clock names. Should contain:
32	"dmamux0" - clock name of mux0 group
33	"dmamux1" - clock name of mux1 group
34	Note: No dmamux0 on i.mx7ulp, but another 'dma' clk added on i.mx7ulp.
35- clocks : A list of phandle and clock-specifier pairs, one for each entry in
36	clock-names.
37
38Optional properties:
39- big-endian: If present registers and hardware scatter/gather descriptors
40	of the eDMA are implemented in big endian mode, otherwise in little
41	mode.
42- interrupt-names : Should contain the below on vf610 similar SoC but not used
43	on i.mx7ulp similar SoC:
44	"edma-tx" - the transmission interrupt
45	"edma-err" - the error interrupt
46
47
48Examples:
49
50edma0: dma-controller@40018000 {
51	#dma-cells = <2>;
52	compatible = "fsl,vf610-edma";
53	reg = <0x40018000 0x2000>,
54		<0x40024000 0x1000>,
55		<0x40025000 0x1000>;
56	interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>,
57		<0 9 IRQ_TYPE_LEVEL_HIGH>;
58	interrupt-names = "edma-tx", "edma-err";
59	dma-channels = <32>;
60	clock-names = "dmamux0", "dmamux1";
61	clocks = <&clks VF610_CLK_DMAMUX0>,
62		<&clks VF610_CLK_DMAMUX1>;
63}; /* vf610 */
64
65edma1: dma-controller@40080000 {
66	#dma-cells = <2>;
67	compatible = "fsl,imx7ulp-edma";
68	reg = <0x40080000 0x2000>,
69		<0x40210000 0x1000>;
70	dma-channels = <32>;
71	interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
72		     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
73		     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
74		     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
75		     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
76		     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
77		     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
78		     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
79		     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
80		     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
81		     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
82		     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
83		     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
84		     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
85		     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
86		     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
87		     /* last is eDMA2-ERR interrupt */
88		     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
89	clock-names = "dma", "dmamux0";
90	clocks = <&pcc2 IMX7ULP_CLK_DMA1>,
91		 <&pcc2 IMX7ULP_CLK_DMA_MUX1>;
92}; /* i.mx7ulp */
93
94* DMA clients
95DMA client drivers that uses the DMA function must use the format described
96in the dma.txt file, using a two-cell specifier for each channel: the 1st
97specifies the channel group(DMAMUX) in which this request can be multiplexed,
98and the 2nd specifies the request source.
99
100Examples:
101
102sai2: sai@40031000 {
103	compatible = "fsl,vf610-sai";
104	reg = <0x40031000 0x1000>;
105	interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
106	clock-names = "sai";
107	clocks = <&clks VF610_CLK_SAI2>;
108	dma-names = "tx", "rx";
109	dmas = <&edma0 0 21>,
110		<&edma0 0 20>;
111};
112