1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/soc/ti/wkup-m3-ipc.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Wakeup M3 IPC device
8
9maintainers:
10  - Dave Gerlach <d-gerlach@ti.com>
11  - Drew Fustini <dfustini@baylibre.com>
12
13description: |+
14  The TI AM33xx and AM43xx family of devices use a small Cortex M3 co-processor
15  (commonly referred to as Wakeup M3 or CM3) to help with various low power tasks
16  that cannot be controlled from the MPU, like suspend/resume and certain deep
17  C-states for CPU Idle. Once the wkup_m3_ipc driver uses the wkup_m3_rproc driver
18  to boot the wkup_m3, it handles communication with the CM3 using IPC registers
19  present in the SoC's control module and a mailbox. The wkup_m3_ipc exposes an
20  API to allow the SoC PM code to execute specific PM tasks.
21
22  Wkup M3 Device Node
23  ====================
24  A wkup_m3_ipc device node is used to represent the IPC registers within an
25  SoC.
26
27  Support for VTT Toggle with GPIO pin
28  ====================================
29  On some boards like the AM335x EVM-SK and the AM437x GP EVM, a GPIO pin is
30  connected to the enable pin on the DDR VTT regulator. This allows the
31  regulator to be disabled upon suspend and enabled upon resume. Please note
32  that the GPIO pin must be part of the GPIO0 module as only this GPIO module
33  is in the wakeup power domain.
34
35  Support for IO Isolation
36  ========================
37  On AM437x SoCs, certain pins can be forced into an alternate state when IO
38  isolation is activated. Those pins have pad control registers prefixed by
39  'CTRL_CONF_' that contain DS0 (e.g. deep sleep) configuration bits that can
40  override the pin's existing bias (pull-up/pull-down) and value (high/low) when
41  IO isolation is active.
42
43  Support for I2C PMIC Voltage Scaling
44  ====================================
45  It is possible to pass the name of a binary file to load into the CM3 memory.
46  The binary data is the I2C sequences for the CM3 to send out to the PMIC
47  during low power mode entry.
48
49properties:
50  compatible:
51    enum:
52      - ti,am3352-wkup-m3-ipc # for AM33xx SoCs
53      - ti,am4372-wkup-m3-ipc # for AM43xx SoCs
54
55  reg:
56    description:
57      The IPC register address space to communicate with the Wakeup M3 processor
58    maxItems: 1
59
60  interrupts:
61    description: wkup_m3 interrupt that signals the MPU
62    maxItems: 1
63
64  ti,rproc:
65    $ref: /schemas/types.yaml#/definitions/phandle
66    description:
67      phandle to the wkup_m3 rproc node so the IPC driver can boot it
68
69  mboxes:
70    description:
71      phandles used by IPC framework to get correct mbox
72      channel for communication. Must point to appropriate
73      mbox_wkupm3 child node.
74    maxItems: 1
75
76  firmware-name:
77    description:
78      Name of binary file with I2C sequences for PMIC voltage scaling
79
80  ti,vtt-gpio-pin:
81    $ref: /schemas/types.yaml#/definitions/uint32
82    description: GPIO pin connected to enable pin on VTT regulator
83
84  ti,set-io-isolation:
85    type: boolean
86    description:
87      If this property is present, then the wkup_m3_ipc driver will instruct
88      the CM3 firmware to activate IO isolation when suspending to deep sleep.
89      This can be leveraged by a board design to put other devices on the board
90      into a low power state.
91
92allOf:
93  - if:
94      properties:
95        compatible:
96          not:
97            contains:
98              const: ti,am4372-wkup-m3-ipc
99    then:
100      properties:
101        ti,set-io-isolation: false
102
103required:
104  - compatible
105  - reg
106  - interrupts
107  - ti,rproc
108  - mboxes
109
110additionalProperties: false
111
112examples:
113  - |
114    /* Example for AM335x SoC */
115    soc {
116        #address-cells = <1>;
117        #size-cells = <1>;
118
119        am335x_mailbox: mailbox {
120            #mbox-cells = <1>;
121        };
122
123        wkup_m3_ipc@1324 {
124           compatible = "ti,am3352-wkup-m3-ipc";
125           reg = <0x1324 0x24>;
126           interrupts = <78>;
127           ti,rproc = <&wkup_m3>;
128           mboxes = <&am335x_mailbox &mbox_wkupm3>;
129           ti,vtt-gpio-pin = <7>;
130           firmware-name = "am335x-evm-scale-data.bin";
131        };
132    };
133
134  - |
135    /*
136     * Example for AM473x SoC:
137     * On the AM437x-GP-EVM board, gpio5_7 is wired to enable pin of the DDR VTT
138     * regulator. The 'ddr_vtt_toggle_default' pinmux node configures gpio5_7
139     * for pull-up during normal system operation. However, the DS0 (deep sleep)
140     * state of the pin is configured for pull-down and thus the VTT regulator
141     * will be disabled to save power when IO isolation is active. Note that
142     * this method is an alternative to using the 'ti,vtt-gpio-pin' property.
143     */
144    #include <dt-bindings/pinctrl/am43xx.h>
145    soc {
146        #address-cells = <1>;
147        #size-cells = <1>;
148
149        am437x_mailbox: mailbox {
150            #mbox-cells = <1>;
151        };
152
153        am43xx_pinmux {
154            pinctrl-names = "default";
155            pinctrl-0 = <&ddr3_vtt_toggle_default>;
156
157            ddr3_vtt_toggle_default: ddr_vtt_toggle_default {
158                 pinctrl-single,pins = <
159                    0x25C (DS0_PULL_UP_DOWN_EN | PIN_OUTPUT_PULLUP | DS0_FORCE_OFF_MODE | MUX_MODE7)
160                 >;
161            };
162        };
163
164        wkup_m3_ipc@1324 {
165           compatible = "ti,am4372-wkup-m3-ipc";
166           reg = <0x1324 0x24>;
167           interrupts = <78>;
168           ti,rproc = <&wkup_m3>;
169           mboxes = <&am437x_mailbox &mbox_wkupm3>;
170           ti,set-io-isolation;
171           firmware-name = "am43x-evm-scale-data.bin";
172        };
173    };
174
175...
176