1Generic USB Device Properties
2
3Usually, we only use device tree for hard wired USB device.
4The reference binding doc is from:
5http://www.devicetree.org/open-firmware/bindings/usb/usb-1_0.ps
6
7Four types of device-tree nodes are defined: "host-controller nodes"
8representing USB host controllers, "device nodes" representing USB devices,
9"interface nodes" representing USB interfaces and "combined nodes"
10representing simple USB devices.
11
12A combined node shall be used instead of a device node and an interface node
13for devices of class 0 or 9 (hub) with a single configuration and a single
14interface.
15
16A "hub node" is a combined node or an interface node that represents a USB
17hub.
18
19
20Required properties for device nodes:
21- compatible: "usbVID,PID", where VID is the vendor id and PID the product id.
22  The textual representation of VID and PID shall be in lower case hexadecimal
23  with leading zeroes suppressed. The other compatible strings from the above
24  standard binding could also be used, but a device adhering to this binding
25  may leave out all except for "usbVID,PID".
26- reg: the number of the USB hub port or the USB host-controller port to which
27  this device is attached. The range is 1-255.
28
29
30Required properties for device nodes with interface nodes:
31- #address-cells: shall be 2
32- #size-cells: shall be 0
33
34
35Required properties for interface nodes:
36- compatible: "usbifVID,PID.configCN.IN", where VID is the vendor id, PID is
37  the product id, CN is the configuration value and IN is the interface
38  number. The textual representation of VID, PID, CN and IN shall be in lower
39  case hexadecimal with leading zeroes suppressed. The other compatible
40  strings from the above standard binding could also be used, but a device
41  adhering to this binding may leave out all except for
42  "usbifVID,PID.configCN.IN".
43- reg: the interface number and configuration value
44
45The configuration component is not included in the textual representation of
46an interface-node unit address for configuration 1.
47
48
49Required properties for combined nodes:
50- compatible: "usbVID,PID", where VID is the vendor id and PID the product id.
51  The textual representation of VID and PID shall be in lower case hexadecimal
52  with leading zeroes suppressed. The other compatible strings from the above
53  standard binding could also be used, but a device adhering to this binding
54  may leave out all except for "usbVID,PID".
55- reg: the number of the USB hub port or the USB host-controller port to which
56  this device is attached. The range is 1-255.
57
58
59Required properties for hub nodes with device nodes:
60- #address-cells: shall be 1
61- #size-cells: shall be 0
62
63
64Required properties for host-controller nodes with device nodes:
65- #address-cells: shall be 1
66- #size-cells: shall be 0
67
68
69Example:
70
71&usb1 {	/* host controller */
72	#address-cells = <1>;
73	#size-cells = <0>;
74
75	hub@1 {		/* hub connected to port 1 */
76		compatible = "usb5e3,608";
77		reg = <1>;
78	};
79
80	device@2 {	/* device connected to port 2 */
81		compatible = "usb123,4567";
82		reg = <2>;
83	};
84
85	device@3 { 	/* device connected to port 3 */
86		compatible = "usb123,abcd";
87		reg = <3>;
88
89		#address-cells = <2>;
90		#size-cells = <0>;
91
92		interface@0 {	/* interface 0 of configuration 1 */
93			compatible = "usbif123,abcd.config1.0";
94			reg = <0 1>;
95		};
96
97		interface@0,2 {	/* interface 0 of configuration 2 */
98			compatible = "usbif123,abcd.config2.0";
99			reg = <0 2>;
100		};
101	};
102};
103