1// SPDX-License-Identifier: BSD-3-Clause
2/*
3 * OnePlus 5(T) (cheeseburger / dumpling) common device tree source based on msm8998-mtp.dtsi
4 *
5 * Copyright (c) 2021, Jami Kettunen <jamipkettunen@gmail.com>
6 * Copyright (c) 2016, The Linux Foundation. All rights reserved.
7 */
8
9/dts-v1/;
10
11#include <dt-bindings/gpio/gpio.h>
12#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
13#include "msm8998.dtsi"
14#include "pm8005.dtsi"
15#include "pm8998.dtsi"
16#include "pmi8998.dtsi"
17
18/ {
19	/* Required for bootloader to select correct board */
20	qcom,msm-id = <292 0x20001>; /* 8998 v2.1 */
21
22	chosen {
23		#address-cells = <2>;
24		#size-cells = <2>;
25		ranges;
26
27		/* Use display framebuffer setup by the UEFI XBL bootloader for simplefb */
28		framebuffer0: framebuffer@9d400000 {
29			compatible = "simple-framebuffer";
30			reg = <0x0 0x9d400000 0x0 0x2400000>;
31			width = <1080>;
32			height = <1920>;
33			stride = <(1080 * 4)>;
34			format = "a8r8g8b8";
35			/*
36			* That's a lot of clocks, but it's necessary due
37			* to unused clk cleanup & no panel driver yet..
38			*/
39			clocks = <&mmcc MDSS_AHB_CLK>,
40				 <&mmcc MDSS_AXI_CLK>,
41				 <&mmcc MDSS_VSYNC_CLK>,
42				 <&mmcc MDSS_MDP_CLK>,
43				 <&mmcc MDSS_BYTE0_CLK>,
44				 <&mmcc MDSS_BYTE0_INTF_CLK>,
45				 <&mmcc MDSS_PCLK0_CLK>,
46				 <&mmcc MDSS_ESC0_CLK>;
47			power-domains = <&mmcc MDSS_GDSC>;
48		};
49	};
50
51	reserved-memory {
52		/* Bootloader display framebuffer region */
53		cont_splash_mem: memory@9d400000 {
54			reg = <0x0 0x9d400000 0x0 0x2400000>;
55			no-map;
56		};
57
58		/* For getting crash logs using Android downstream kernels */
59		ramoops@ac000000 {
60			compatible = "ramoops";
61			reg = <0x0 0xac000000 0x0 0x200000>;
62			console-size = <0x80000>;
63			pmsg-size = <0x40000>;
64			record-size = <0x8000>;
65			ftrace-size = <0x20000>;
66		};
67
68		/*
69		 * The following memory regions on downstream are "dynamically allocated"
70		 * but given the same addresses every time. Hard code them as these addresses
71		 * are where the OnePlus signed firmware expects them to be.
72		 */
73		ipa_fws_region: ipa@f6800000 {
74			compatible = "shared-dma-pool";
75			reg = <0x0 0xf6800000 0x0 0x5000>;
76			no-map;
77		};
78		zap_shader_region: gpu@f6900000 {
79			compatible = "shared-dma-pool";
80			reg = <0x0 0xf6900000 0x0 0x2000>;
81			no-map;
82		};
83	};
84
85	gpio-keys {
86		compatible = "gpio-keys";
87		label = "Volume buttons";
88		autorepeat;
89
90		pinctrl-names = "default";
91		pinctrl-0 = <&vol_keys_default>;
92
93		button-vol-down {
94			label = "Volume down";
95			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
96			linux,code = <KEY_VOLUMEDOWN>;
97			debounce-interval = <15>;
98			wakeup-source;
99		};
100
101		button-vol-up {
102			label = "Volume up";
103			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
104			linux,code = <KEY_VOLUMEUP>;
105			debounce-interval = <15>;
106			wakeup-source;
107		};
108	};
109
110	gpio-hall-sensor {
111		compatible = "gpio-keys";
112		label = "Hall effect sensor";
113
114		pinctrl-names = "default";
115		pinctrl-0 = <&hall_sensor_default>;
116
117		event-hall-sensor {
118			label = "Hall Effect Sensor";
119			gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
120			linux,input-type = <EV_SW>;
121			linux,code = <SW_LID>;
122			linux,can-disable;
123			wakeup-source;
124		};
125	};
126
127	vph_pwr: vph-pwr-regulator {
128		compatible = "regulator-fixed";
129		regulator-name = "vph_pwr";
130		regulator-always-on;
131		regulator-boot-on;
132	};
133};
134
135/*
136 * OnePlus' ADSP firmware requires 30 MiB in total, so increase the adsp_mem
137 * region by 4 MiB to account for this while relocating the other now
138 * conflicting memory nodes accordingly.
139 */
140&adsp_mem {
141	reg = <0x0 0x8b200000 0x0 0x1e00000>;
142};
143&mpss_mem {
144	reg = <0x0 0x8d000000 0x0 0x7000000>;
145};
146&venus_mem {
147	reg = <0x0 0x94000000 0x0 0x500000>;
148};
149&mba_mem {
150	reg = <0x0 0x94500000 0x0 0x200000>;
151};
152&slpi_mem {
153	reg = <0x0 0x94700000 0x0 0xf00000>;
154};
155&ipa_fw_mem {
156	reg = <0x0 0x95600000 0x0 0x10000>;
157};
158&ipa_gsi_mem {
159	reg = <0x0 0x95610000 0x0 0x5000>;
160};
161&gpu_mem {
162	reg = <0x0 0x95615000 0x0 0x100000>;
163};
164&wlan_msa_mem {
165	reg = <0x0 0x95715000 0x0 0x100000>;
166};
167
168&blsp1_i2c5 {
169	status = "okay";
170
171	touchscreen@20 {
172		compatible = "syna,rmi4-i2c";
173		reg = <0x20>;
174		#address-cells = <1>;
175		#size-cells = <0>;
176
177		interrupt-parent = <&tlmm>;
178		interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
179
180		pinctrl-names = "default";
181		pinctrl-0 = <&ts_int_active &ts_reset_active>;
182
183		vdd-supply = <&vreg_l28_3p0>;
184		vio-supply = <&vreg_l6a_1p8>;
185
186		syna,reset-delay-ms = <20>;
187		syna,startup-delay-ms = <20>;
188
189		rmi4-f01@1 {
190			reg = <0x01>;
191			syna,nosleep-mode = <1>;
192		};
193
194		rmi4_f12: rmi4-f12@12 {
195			reg = <0x12>;
196			syna,rezero-wait-ms = <20>;
197			syna,sensor-type = <1>;
198			touchscreen-x-mm = <68>;
199			touchscreen-y-mm = <122>;
200		};
201	};
202};
203
204&blsp1_i2c6 {
205	status = "okay";
206
207	nfc@28 {
208		compatible = "nxp,nxp-nci-i2c";
209		reg = <0x28>;
210
211		interrupt-parent = <&tlmm>;
212		interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
213
214		enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
215
216		pinctrl-names = "default";
217		pinctrl-0 = <&nfc_int_active &nfc_enable_active>;
218	};
219};
220
221&blsp1_uart3 {
222	status = "okay";
223
224	bluetooth {
225		compatible = "qcom,wcn3990-bt";
226
227		vddio-supply = <&vreg_s4a_1p8>;
228		vddxo-supply = <&vreg_l7a_1p8>;
229		vddrf-supply = <&vreg_l17a_1p3>;
230		vddch0-supply = <&vreg_l25a_3p3>;
231		max-speed = <3200000>;
232	};
233};
234
235&blsp1_uart3_on {
236	rx {
237		/delete-property/ bias-disable;
238		/*
239		 * Configure a pull-up on 46 (RX). This is needed to
240		 * avoid garbage data when the TX pin of the Bluetooth
241		 * module is in tri-state (module powered off or not
242		 * driving the signal yet).
243		 */
244		bias-pull-up;
245	};
246
247	cts {
248		/delete-property/ bias-disable;
249		/*
250		 * Configure a pull-down on 47 (CTS) to match the pull
251		 * of the Bluetooth module.
252		 */
253		bias-pull-down;
254	};
255};
256
257&blsp2_uart1 {
258	status = "okay";
259};
260
261&pm8005_regulators {
262	/* VDD_GFX supply */
263	pm8005_s1: s1 {
264		regulator-min-microvolt = <524000>;
265		regulator-max-microvolt = <1100000>;
266		regulator-enable-ramp-delay = <500>;
267		/* Hack until we rig up the gpu consumer */
268		regulator-always-on;
269	};
270};
271
272&pm8998_gpio {
273	vol_keys_default: vol-keys-state {
274		pins = "gpio5", "gpio6";
275		function = "normal";
276		bias-pull-up;
277		input-enable;
278		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
279	};
280};
281
282&qusb2phy {
283	status = "okay";
284
285	vdd-supply = <&vreg_l1a_0p875>;
286	vdda-pll-supply = <&vreg_l12a_1p8>;
287	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
288};
289
290&rpm_requests {
291	pm8998-regulators {
292		compatible = "qcom,rpm-pm8998-regulators";
293
294		vdd_s1-supply = <&vph_pwr>;
295		vdd_s2-supply = <&vph_pwr>;
296		vdd_s3-supply = <&vph_pwr>;
297		vdd_s4-supply = <&vph_pwr>;
298		vdd_s5-supply = <&vph_pwr>;
299		vdd_s6-supply = <&vph_pwr>;
300		vdd_s7-supply = <&vph_pwr>;
301		vdd_s8-supply = <&vph_pwr>;
302		vdd_s9-supply = <&vph_pwr>;
303		vdd_s10-supply = <&vph_pwr>;
304		vdd_s11-supply = <&vph_pwr>;
305		vdd_s12-supply = <&vph_pwr>;
306		vdd_s13-supply = <&vph_pwr>;
307		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
308		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
309		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
310		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
311		vdd_l6-supply = <&vreg_s5a_2p04>;
312		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
313		vdd_l9-supply = <&vreg_bob>;
314		vdd_l10_l23_l25-supply = <&vreg_bob>;
315		vdd_l13_l19_l21-supply = <&vreg_bob>;
316		vdd_l16_l28-supply = <&vreg_bob>;
317		vdd_l18_l22-supply = <&vreg_bob>;
318		vdd_l20_l24-supply = <&vreg_bob>;
319		vdd_l26-supply = <&vreg_s3a_1p35>;
320		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
321
322		vreg_s3a_1p35: s3 {
323			regulator-min-microvolt = <1352000>;
324			regulator-max-microvolt = <1352000>;
325		};
326
327		vreg_s4a_1p8: s4 {
328			regulator-min-microvolt = <1800000>;
329			regulator-max-microvolt = <1800000>;
330			regulator-allow-set-load;
331		};
332
333		vreg_s5a_2p04: s5 {
334			regulator-min-microvolt = <1904000>;
335			regulator-max-microvolt = <2040000>;
336		};
337
338		vreg_s7a_1p025: s7 {
339			regulator-min-microvolt = <900000>;
340			regulator-max-microvolt = <1028000>;
341		};
342
343		vreg_l1a_0p875: l1 {
344			regulator-min-microvolt = <880000>;
345			regulator-max-microvolt = <880000>;
346		};
347
348		vreg_l2a_1p2: l2 {
349			regulator-min-microvolt = <1200000>;
350			regulator-max-microvolt = <1200000>;
351		};
352
353		vreg_l3a_1p0: l3 {
354			regulator-min-microvolt = <1000000>;
355			regulator-max-microvolt = <1000000>;
356		};
357
358		vreg_l5a_0p8: l5 {
359			regulator-min-microvolt = <800000>;
360			regulator-max-microvolt = <800000>;
361		};
362
363		vreg_l6a_1p8: l6 {
364			regulator-min-microvolt = <1808000>;
365			regulator-max-microvolt = <1808000>;
366		};
367
368		vreg_l7a_1p8: l7 {
369			regulator-min-microvolt = <1800000>;
370			regulator-max-microvolt = <1800000>;
371		};
372
373		vreg_l8a_1p2: l8 {
374			regulator-min-microvolt = <1200000>;
375			regulator-max-microvolt = <1200000>;
376		};
377
378		vreg_l9a_1p8: l9 {
379			regulator-min-microvolt = <1808000>;
380			regulator-max-microvolt = <2960000>;
381		};
382
383		vreg_l10a_1p8: l10 {
384			regulator-min-microvolt = <1808000>;
385			regulator-max-microvolt = <2960000>;
386		};
387
388		vreg_l11a_1p0: l11 {
389			regulator-min-microvolt = <1000000>;
390			regulator-max-microvolt = <1000000>;
391		};
392
393		vreg_l12a_1p8: l12 {
394			regulator-min-microvolt = <1800000>;
395			regulator-max-microvolt = <1800000>;
396		};
397
398		vreg_l13a_2p95: l13 {
399			regulator-min-microvolt = <1808000>;
400			regulator-max-microvolt = <2960000>;
401		};
402
403		vreg_l14a_1p88: l14 {
404			regulator-min-microvolt = <1880000>;
405			regulator-max-microvolt = <1880000>;
406		};
407
408		vreg_l15a_1p8: l15 {
409			regulator-min-microvolt = <1800000>;
410			regulator-max-microvolt = <1800000>;
411		};
412
413		vreg_l16a_2p7: l16 {
414			regulator-min-microvolt = <2704000>;
415			regulator-max-microvolt = <2704000>;
416		};
417
418		vreg_l17a_1p3: l17 {
419			regulator-min-microvolt = <1304000>;
420			regulator-max-microvolt = <1304000>;
421		};
422
423		vreg_l18a_2p7: l18 {
424			regulator-min-microvolt = <2704000>;
425			regulator-max-microvolt = <2704000>;
426		};
427
428		vreg_l19a_3p0: l19 {
429			regulator-min-microvolt = <3008000>;
430			regulator-max-microvolt = <3008000>;
431		};
432
433		vreg_l20a_2p95: l20 {
434			regulator-min-microvolt = <2960000>;
435			regulator-max-microvolt = <2960000>;
436			regulator-allow-set-load;
437		};
438		vreg_l21a_2p95: l21 {
439			regulator-min-microvolt = <2960000>;
440			regulator-max-microvolt = <2960000>;
441			regulator-system-load = <800000>;
442			regulator-allow-set-load;
443		};
444
445		vreg_l22a_2p85: l22 {
446			regulator-min-microvolt = <2864000>;
447			regulator-max-microvolt = <2864000>;
448		};
449
450		vreg_l23a_3p3: l23 {
451			regulator-min-microvolt = <3312000>;
452			regulator-max-microvolt = <3312000>;
453		};
454
455		vreg_l24a_3p075: l24 {
456			regulator-min-microvolt = <3088000>;
457			regulator-max-microvolt = <3088000>;
458		};
459
460		vreg_l25a_3p3: l25 {
461			regulator-min-microvolt = <3104000>;
462			regulator-max-microvolt = <3312000>;
463		};
464
465		vreg_l26a_1p2: l26 {
466			regulator-min-microvolt = <1200000>;
467			regulator-max-microvolt = <1200000>;
468			regulator-allow-set-load;
469		};
470
471		vreg_l28_3p0: l28 {
472			regulator-min-microvolt = <3008000>;
473			regulator-max-microvolt = <3008000>;
474		};
475
476		vreg_lvs1a_1p8: lvs1 { };
477		vreg_lvs2a_1p8: lvs2 { };
478	};
479
480	pmi8998-regulators {
481		compatible = "qcom,rpm-pmi8998-regulators";
482
483		vdd_bob-supply = <&vph_pwr>;
484
485		vreg_bob: bob {
486			regulator-min-microvolt = <3312000>;
487			regulator-max-microvolt = <3600000>;
488		};
489	};
490};
491
492&tlmm {
493	gpio-reserved-ranges = <0 4>, <81 4>;
494
495	hall_sensor_default: hall-sensor-default {
496		pins = "gpio124";
497		function = "gpio";
498		drive-strength = <2>;
499		bias-disable;
500		input-enable;
501	};
502
503	ts_int_active: ts-int-active {
504		pins = "gpio125";
505		function = "gpio";
506		drive-strength = <8>;
507		bias-pull-up;
508	};
509
510	ts_reset_active: ts-reset-active {
511		pins = "gpio89";
512		function = "gpio";
513		drive-strength = <8>;
514		bias-pull-up;
515	};
516
517	nfc_int_active: nfc-int-active {
518		pins = "gpio92";
519		function = "gpio";
520		drive-strength = <6>;
521		bias-pull-up;
522	};
523
524	nfc_enable_active: nfc-enable-active {
525		pins = "gpio12", "gpio116";
526		function = "gpio";
527		drive-strength = <6>;
528		bias-pull-up;
529	};
530};
531
532&ufshc {
533	status = "okay";
534
535	vcc-supply = <&vreg_l20a_2p95>;
536	vccq-supply = <&vreg_l26a_1p2>;
537	vccq2-supply = <&vreg_s4a_1p8>;
538	vcc-max-microamp = <750000>;
539	vccq-max-microamp = <560000>;
540	vccq2-max-microamp = <750000>;
541};
542
543&ufsphy {
544	status = "okay";
545
546	vdda-phy-supply = <&vreg_l1a_0p875>;
547	vdda-pll-supply = <&vreg_l2a_1p2>;
548	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
549};
550
551&usb3 {
552	status = "okay";
553
554	/* Disable USB3 clock requirement as the device only supports USB2 */
555	qcom,select-utmi-as-pipe-clk;
556};
557
558&usb3_dwc3 {
559	/* Drop the unused USB 3 PHY */
560	phys = <&qusb2phy>;
561	phy-names = "usb2-phy";
562
563	/* Fastest mode for USB 2 */
564	maximum-speed = "high-speed";
565
566	/* Force to peripheral until we can switch modes */
567	dr_mode = "peripheral";
568};
569
570&wifi {
571	/* Leave disabled until MSS is functional */
572	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
573	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
574	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
575	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
576};
577