1// SPDX-License-Identifier: BSD-3-Clause
2/*
3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
4 * Copyright (c) 2019, Linaro Limited
5 */
6
7#include <dt-bindings/input/input.h>
8#include <dt-bindings/interrupt-controller/irq.h>
9#include <dt-bindings/spmi/spmi.h>
10#include <dt-bindings/iio/qcom,spmi-vadc.h>
11
12/ {
13	thermal-zones {
14		pm8150-thermal {
15			polling-delay-passive = <100>;
16			polling-delay = <0>;
17
18			thermal-sensors = <&pm8150_temp>;
19
20			trips {
21				trip0 {
22					temperature = <95000>;
23					hysteresis = <0>;
24					type = "passive";
25				};
26
27				trip1 {
28					temperature = <115000>;
29					hysteresis = <0>;
30					type = "hot";
31				};
32
33				trip2 {
34					temperature = <145000>;
35					hysteresis = <0>;
36					type = "critical";
37				};
38			};
39		};
40	};
41};
42
43&spmi_bus {
44	pm8150_0: pmic@0 {
45		compatible = "qcom,pm8150", "qcom,spmi-pmic";
46		reg = <0x0 SPMI_USID>;
47		#address-cells = <1>;
48		#size-cells = <0>;
49
50		pon: power-on@800 {
51			compatible = "qcom,pm8916-pon";
52			reg = <0x0800>;
53			pwrkey {
54				compatible = "qcom,pm8941-pwrkey";
55				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
56				debounce = <15625>;
57				bias-pull-up;
58				linux,code = <KEY_POWER>;
59
60				status = "disabled";
61			};
62		};
63
64		pm8150_temp: temp-alarm@2400 {
65			compatible = "qcom,spmi-temp-alarm";
66			reg = <0x2400>;
67			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
68			io-channels = <&pm8150_adc ADC5_DIE_TEMP>;
69			io-channel-names = "thermal";
70			#thermal-sensor-cells = <0>;
71		};
72
73		pm8150_adc: adc@3100 {
74			compatible = "qcom,spmi-adc5";
75			reg = <0x3100>;
76			#address-cells = <1>;
77			#size-cells = <0>;
78			#io-channel-cells = <1>;
79			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
80
81			ref-gnd@0 {
82				reg = <ADC5_REF_GND>;
83				qcom,pre-scaling = <1 1>;
84				label = "ref_gnd";
85			};
86
87			vref-1p25@1 {
88				reg = <ADC5_1P25VREF>;
89				qcom,pre-scaling = <1 1>;
90				label = "vref_1p25";
91			};
92
93			die-temp@6 {
94				reg = <ADC5_DIE_TEMP>;
95				qcom,pre-scaling = <1 1>;
96				label = "die_temp";
97			};
98		};
99
100		pm8150_adc_tm: adc-tm@3500 {
101			compatible = "qcom,spmi-adc-tm5";
102			reg = <0x3500>;
103			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
104			#thermal-sensor-cells = <1>;
105			#address-cells = <1>;
106			#size-cells = <0>;
107			status = "disabled";
108		};
109
110		rtc@6000 {
111			compatible = "qcom,pm8941-rtc";
112			reg = <0x6000>;
113			reg-names = "rtc", "alarm";
114			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
115		};
116
117		pm8150_gpios: gpio@c000 {
118			compatible = "qcom,pm8150-gpio";
119			reg = <0xc000>;
120			gpio-controller;
121			#gpio-cells = <2>;
122			interrupt-controller;
123			#interrupt-cells = <2>;
124		};
125	};
126
127	pmic@1 {
128		compatible = "qcom,pm8150", "qcom,spmi-pmic";
129		reg = <0x1 SPMI_USID>;
130		#address-cells = <1>;
131		#size-cells = <0>;
132	};
133};
134