1// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2/*
3 * Device Tree Source for the RZ/G2LC SMARC SOM common parts
4 *
5 * Copyright (C) 2021 Renesas Electronics Corp.
6 */
7
8#include <dt-bindings/gpio/gpio.h>
9#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
10
11/ {
12	aliases {
13		ethernet0 = &eth0;
14	};
15
16	chosen {
17		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
18	};
19
20	memory@48000000 {
21		device_type = "memory";
22		/* first 128MB is reserved for secure area. */
23		reg = <0x0 0x48000000 0x0 0x38000000>;
24	};
25
26	reg_1p8v: regulator-1p8v {
27		compatible = "regulator-fixed";
28		regulator-name = "fixed-1.8V";
29		regulator-min-microvolt = <1800000>;
30		regulator-max-microvolt = <1800000>;
31		regulator-boot-on;
32		regulator-always-on;
33	};
34
35	reg_3p3v: regulator-3p3v {
36		compatible = "regulator-fixed";
37		regulator-name = "fixed-3.3V";
38		regulator-min-microvolt = <3300000>;
39		regulator-max-microvolt = <3300000>;
40		regulator-boot-on;
41		regulator-always-on;
42	};
43
44	reg_1p1v: regulator-vdd-core {
45		compatible = "regulator-fixed";
46		regulator-name = "fixed-1.1V";
47		regulator-min-microvolt = <1100000>;
48		regulator-max-microvolt = <1100000>;
49		regulator-boot-on;
50		regulator-always-on;
51	};
52
53	vccq_sdhi0: regulator-vccq-sdhi0 {
54		compatible = "regulator-gpio";
55
56		regulator-name = "SDHI0 VccQ";
57		regulator-min-microvolt = <1800000>;
58		regulator-max-microvolt = <3300000>;
59		states = <3300000 1>, <1800000 0>;
60		regulator-boot-on;
61		gpios = <&pinctrl RZG2L_GPIO(39, 0) GPIO_ACTIVE_HIGH>;
62		regulator-always-on;
63	};
64};
65
66&eth0 {
67	pinctrl-0 = <&eth0_pins>;
68	pinctrl-names = "default";
69	phy-handle = <&phy0>;
70	phy-mode = "rgmii-id";
71	status = "okay";
72
73	phy0: ethernet-phy@7 {
74		compatible = "ethernet-phy-id0022.1640",
75			     "ethernet-phy-ieee802.3-c22";
76		reg = <7>;
77		rxc-skew-psec = <2400>;
78		txc-skew-psec = <2400>;
79		rxdv-skew-psec = <0>;
80		txdv-skew-psec = <0>;
81		rxd0-skew-psec = <0>;
82		rxd1-skew-psec = <0>;
83		rxd2-skew-psec = <0>;
84		rxd3-skew-psec = <0>;
85		txd0-skew-psec = <0>;
86		txd1-skew-psec = <0>;
87		txd2-skew-psec = <0>;
88		txd3-skew-psec = <0>;
89	};
90};
91
92&extal_clk {
93	clock-frequency = <24000000>;
94};
95
96&gpu {
97	mali-supply = <&reg_1p1v>;
98};
99
100&ostm1 {
101	status = "okay";
102};
103
104&ostm2 {
105	status = "okay";
106};
107
108&pinctrl {
109	eth0_pins: eth0 {
110		pinmux = <RZG2L_PORT_PINMUX(28, 1, 1)>, /* ET0_LINKSTA */
111			 <RZG2L_PORT_PINMUX(27, 1, 1)>, /* ET0_MDC */
112			 <RZG2L_PORT_PINMUX(28, 0, 1)>, /* ET0_MDIO */
113			 <RZG2L_PORT_PINMUX(20, 0, 1)>, /* ET0_TXC */
114			 <RZG2L_PORT_PINMUX(20, 1, 1)>, /* ET0_TX_CTL */
115			 <RZG2L_PORT_PINMUX(20, 2, 1)>, /* ET0_TXD0 */
116			 <RZG2L_PORT_PINMUX(21, 0, 1)>, /* ET0_TXD1 */
117			 <RZG2L_PORT_PINMUX(21, 1, 1)>, /* ET0_TXD2 */
118			 <RZG2L_PORT_PINMUX(22, 0, 1)>, /* ET0_TXD3 */
119			 <RZG2L_PORT_PINMUX(24, 0, 1)>, /* ET0_RXC */
120			 <RZG2L_PORT_PINMUX(24, 1, 1)>, /* ET0_RX_CTL */
121			 <RZG2L_PORT_PINMUX(25, 0, 1)>, /* ET0_RXD0 */
122			 <RZG2L_PORT_PINMUX(25, 1, 1)>, /* ET0_RXD1 */
123			 <RZG2L_PORT_PINMUX(26, 0, 1)>, /* ET0_RXD2 */
124			 <RZG2L_PORT_PINMUX(26, 1, 1)>; /* ET0_RXD3 */
125	};
126
127	gpio-sd0-pwr-en-hog {
128		gpio-hog;
129		gpios = <RZG2L_GPIO(18, 1) GPIO_ACTIVE_HIGH>;
130		output-high;
131		line-name = "gpio_sd0_pwr_en";
132	};
133
134	qspi0_pins: qspi0 {
135		qspi0-data {
136			pins = "QSPI0_IO0", "QSPI0_IO1", "QSPI0_IO2", "QSPI0_IO3";
137			power-source = <1800>;
138		};
139
140		qspi0-ctrl {
141			pins = "QSPI0_SPCLK", "QSPI0_SSL", "QSPI_RESET#";
142			power-source = <1800>;
143		};
144	};
145
146	/*
147	 * SD0 device selection is XOR between GPIO_SD0_DEV_SEL and SW1[2]
148	 * The below switch logic can be used to select the device between
149	 * eMMC and microSD, after setting GPIO_SD0_DEV_SEL to high in DT.
150	 * SW1[2] should be at OFF position to enable 64 GB eMMC
151	 * SW1[2] should be at position ON to enable uSD card CN3
152	 */
153	gpio-sd0-dev-sel-hog {
154		gpio-hog;
155		gpios = <RZG2L_GPIO(40, 2) GPIO_ACTIVE_HIGH>;
156		output-high;
157		line-name = "gpio_sd0_dev_sel";
158	};
159
160	sdhi0_emmc_pins: sd0emmc {
161		sd0_emmc_data {
162			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
163			       "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7";
164			power-source = <1800>;
165		};
166
167		sd0_emmc_ctrl {
168			pins = "SD0_CLK", "SD0_CMD";
169			power-source = <1800>;
170		};
171
172		sd0_emmc_rst {
173			pins = "SD0_RST#";
174			power-source = <1800>;
175		};
176	};
177
178	sdhi0_pins: sd0 {
179		sd0_data {
180			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
181			power-source = <3300>;
182		};
183
184		sd0_ctrl {
185			pins = "SD0_CLK", "SD0_CMD";
186			power-source = <3300>;
187		};
188
189		sd0_mux {
190			pinmux = <RZG2L_PORT_PINMUX(18, 0, 1)>; /* SD0_CD */
191		};
192	};
193
194	sdhi0_pins_uhs: sd0_uhs {
195		sd0_data_uhs {
196			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
197			power-source = <1800>;
198		};
199
200		sd0_ctrl_uhs {
201			pins = "SD0_CLK", "SD0_CMD";
202			power-source = <1800>;
203		};
204
205		sd0_mux_uhs {
206			pinmux = <RZG2L_PORT_PINMUX(18, 0, 1)>; /* SD0_CD */
207		};
208	};
209};
210
211&sbc {
212	pinctrl-0 = <&qspi0_pins>;
213	pinctrl-names = "default";
214	status = "okay";
215
216	flash@0 {
217		compatible = "micron,mt25qu512a", "jedec,spi-nor";
218		reg = <0>;
219		m25p,fast-read;
220		spi-max-frequency = <50000000>;
221		spi-rx-bus-width = <4>;
222
223		partitions {
224			compatible = "fixed-partitions";
225			#address-cells = <1>;
226			#size-cells = <1>;
227
228			boot@0 {
229				reg = <0x00000000 0x2000000>;
230				read-only;
231			};
232			user@2000000 {
233				reg = <0x2000000 0x2000000>;
234			};
235		};
236	};
237};
238
239#if (!SW_SD0_DEV_SEL)
240&sdhi0 {
241	pinctrl-0 = <&sdhi0_pins>;
242	pinctrl-1 = <&sdhi0_pins_uhs>;
243	pinctrl-names = "default", "state_uhs";
244
245	vmmc-supply = <&reg_3p3v>;
246	vqmmc-supply = <&vccq_sdhi0>;
247	bus-width = <4>;
248	sd-uhs-sdr50;
249	sd-uhs-sdr104;
250	status = "okay";
251};
252#endif
253
254#if SW_SD0_DEV_SEL
255&sdhi0 {
256	pinctrl-0 = <&sdhi0_emmc_pins>;
257	pinctrl-1 = <&sdhi0_emmc_pins>;
258	pinctrl-names = "default", "state_uhs";
259
260	vmmc-supply = <&reg_3p3v>;
261	vqmmc-supply = <&reg_1p8v>;
262	bus-width = <8>;
263	mmc-hs200-1_8v;
264	non-removable;
265	fixed-emmc-driver-type = <1>;
266	status = "okay";
267};
268#endif
269
270&wdt0 {
271	status = "okay";
272	timeout-sec = <60>;
273};
274
275&wdt1 {
276	status = "okay";
277	timeout-sec = <60>;
278};
279
280&wdt2 {
281	status = "okay";
282	timeout-sec = <60>;
283};
284