1 /*- 2 * SPDX-License-Identifier: BSD-4-Clause 3 * 4 * Copyright (c) 1997, 1998, 1999, 2000-2003 5 * Bill Paul <wpaul@windriver.com>. All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 3. All advertising materials mentioning features or use of this software 16 * must display the following acknowledgement: 17 * This product includes software developed by Bill Paul. 18 * 4. Neither the name of the author nor the names of any co-contributors 19 * may be used to endorse or promote products derived from this software 20 * without specific prior written permission. 21 * 22 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 23 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 24 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 25 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 26 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 27 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 28 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 29 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 30 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 31 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 32 * THE POSSIBILITY OF SUCH DAMAGE. 33 */ 34 35 #include <sys/cdefs.h> 36 __FBSDID("$FreeBSD$"); 37 38 /* 39 * ASIX Electronics AX88172/AX88178/AX88778 USB 2.0 ethernet driver. 40 * Used in the LinkSys USB200M and various other adapters. 41 * 42 * Manuals available from: 43 * http://www.asix.com.tw/datasheet/mac/Ax88172.PDF 44 * Note: you need the manual for the AX88170 chip (USB 1.x ethernet 45 * controller) to find the definitions for the RX control register. 46 * http://www.asix.com.tw/datasheet/mac/Ax88170.PDF 47 * 48 * Written by Bill Paul <wpaul@windriver.com> 49 * Senior Engineer 50 * Wind River Systems 51 */ 52 53 /* 54 * The AX88172 provides USB ethernet supports at 10 and 100Mbps. 55 * It uses an external PHY (reference designs use a RealTek chip), 56 * and has a 64-bit multicast hash filter. There is some information 57 * missing from the manual which one needs to know in order to make 58 * the chip function: 59 * 60 * - You must set bit 7 in the RX control register, otherwise the 61 * chip won't receive any packets. 62 * - You must initialize all 3 IPG registers, or you won't be able 63 * to send any packets. 64 * 65 * Note that this device appears to only support loading the station 66 * address via autload from the EEPROM (i.e. there's no way to manually 67 * set it). 68 * 69 * (Adam Weinberger wanted me to name this driver if_gir.c.) 70 */ 71 72 /* 73 * Ax88178 and Ax88772 support backported from the OpenBSD driver. 74 * 2007/02/12, J.R. Oldroyd, fbsd@opal.com 75 * 76 * Manual here: 77 * http://www.asix.com.tw/FrootAttach/datasheet/AX88178_datasheet_Rev10.pdf 78 * http://www.asix.com.tw/FrootAttach/datasheet/AX88772_datasheet_Rev10.pdf 79 */ 80 81 #include <sys/param.h> 82 #include <sys/systm.h> 83 #include <sys/bus.h> 84 #include <sys/condvar.h> 85 #include <sys/endian.h> 86 #include <sys/kernel.h> 87 #include <sys/lock.h> 88 #include <sys/malloc.h> 89 #include <sys/mbuf.h> 90 #include <sys/module.h> 91 #include <sys/mutex.h> 92 #include <sys/socket.h> 93 #include <sys/sockio.h> 94 #include <sys/sysctl.h> 95 #include <sys/sx.h> 96 97 #include <net/if.h> 98 #include <net/if_var.h> 99 #include <net/ethernet.h> 100 #include <net/if_types.h> 101 #include <net/if_media.h> 102 #include <net/if_vlan_var.h> 103 104 #include <dev/mii/mii.h> 105 #include <dev/mii/miivar.h> 106 107 #include <dev/usb/usb.h> 108 #include <dev/usb/usbdi.h> 109 #include <dev/usb/usbdi_util.h> 110 #include "usbdevs.h" 111 112 #define USB_DEBUG_VAR axe_debug 113 #include <dev/usb/usb_debug.h> 114 #include <dev/usb/usb_process.h> 115 116 #include <dev/usb/net/usb_ethernet.h> 117 #include <dev/usb/net/if_axereg.h> 118 119 #include "miibus_if.h" 120 121 /* 122 * AXE_178_MAX_FRAME_BURST 123 * max frame burst size for Ax88178 and Ax88772 124 * 0 2048 bytes 125 * 1 4096 bytes 126 * 2 8192 bytes 127 * 3 16384 bytes 128 * use the largest your system can handle without USB stalling. 129 * 130 * NB: 88772 parts appear to generate lots of input errors with 131 * a 2K rx buffer and 8K is only slightly faster than 4K on an 132 * EHCI port on a T42 so change at your own risk. 133 */ 134 #define AXE_178_MAX_FRAME_BURST 1 135 136 #define AXE_CSUM_FEATURES (CSUM_IP | CSUM_TCP | CSUM_UDP) 137 138 #ifdef USB_DEBUG 139 static int axe_debug = 0; 140 141 static SYSCTL_NODE(_hw_usb, OID_AUTO, axe, CTLFLAG_RW | CTLFLAG_MPSAFE, 0, 142 "USB axe"); 143 SYSCTL_INT(_hw_usb_axe, OID_AUTO, debug, CTLFLAG_RWTUN, &axe_debug, 0, 144 "Debug level"); 145 #endif 146 147 /* 148 * Various supported device vendors/products. 149 */ 150 static const STRUCT_USB_HOST_ID axe_devs[] = { 151 #define AXE_DEV(v,p,i) { USB_VPI(USB_VENDOR_##v, USB_PRODUCT_##v##_##p, i) } 152 AXE_DEV(ABOCOM, UF200, 0), 153 AXE_DEV(ACERCM, EP1427X2, 0), 154 AXE_DEV(APPLE, ETHERNET, AXE_FLAG_772), 155 AXE_DEV(ASIX, AX88172, 0), 156 AXE_DEV(ASIX, AX88178, AXE_FLAG_178), 157 AXE_DEV(ASIX, AX88772, AXE_FLAG_772), 158 AXE_DEV(ASIX, AX88772A, AXE_FLAG_772A), 159 AXE_DEV(ASIX, AX88772B, AXE_FLAG_772B), 160 AXE_DEV(ASIX, AX88772B_1, AXE_FLAG_772B), 161 AXE_DEV(ATEN, UC210T, 0), 162 AXE_DEV(BELKIN, F5D5055, AXE_FLAG_178), 163 AXE_DEV(BILLIONTON, USB2AR, 0), 164 AXE_DEV(CISCOLINKSYS, USB200MV2, AXE_FLAG_772A), 165 AXE_DEV(COREGA, FETHER_USB2_TX, 0), 166 AXE_DEV(DLINK, DUBE100, 0), 167 AXE_DEV(DLINK, DUBE100B1, AXE_FLAG_772), 168 AXE_DEV(DLINK, DUBE100C1, AXE_FLAG_772B), 169 AXE_DEV(GOODWAY, GWUSB2E, 0), 170 AXE_DEV(IODATA, ETGUS2, AXE_FLAG_178), 171 AXE_DEV(JVC, MP_PRX1, 0), 172 AXE_DEV(LENOVO, ETHERNET, AXE_FLAG_772B), 173 AXE_DEV(LINKSYS2, USB200M, 0), 174 AXE_DEV(LINKSYS4, USB1000, AXE_FLAG_178), 175 AXE_DEV(LOGITEC, LAN_GTJU2A, AXE_FLAG_178), 176 AXE_DEV(MELCO, LUAU2KTX, 0), 177 AXE_DEV(MELCO, LUA3U2AGT, AXE_FLAG_178), 178 AXE_DEV(NETGEAR, FA120, 0), 179 AXE_DEV(OQO, ETHER01PLUS, AXE_FLAG_772), 180 AXE_DEV(PLANEX3, GU1000T, AXE_FLAG_178), 181 AXE_DEV(SITECOM, LN029, 0), 182 AXE_DEV(SITECOMEU, LN028, AXE_FLAG_178), 183 AXE_DEV(SITECOMEU, LN031, AXE_FLAG_178), 184 AXE_DEV(SYSTEMTALKS, SGCX2UL, 0), 185 #undef AXE_DEV 186 }; 187 188 static device_probe_t axe_probe; 189 static device_attach_t axe_attach; 190 static device_detach_t axe_detach; 191 192 static usb_callback_t axe_bulk_read_callback; 193 static usb_callback_t axe_bulk_write_callback; 194 195 static miibus_readreg_t axe_miibus_readreg; 196 static miibus_writereg_t axe_miibus_writereg; 197 static miibus_statchg_t axe_miibus_statchg; 198 199 static uether_fn_t axe_attach_post; 200 static uether_fn_t axe_init; 201 static uether_fn_t axe_stop; 202 static uether_fn_t axe_start; 203 static uether_fn_t axe_tick; 204 static uether_fn_t axe_setmulti; 205 static uether_fn_t axe_setpromisc; 206 207 static int axe_attach_post_sub(struct usb_ether *); 208 static int axe_ifmedia_upd(struct ifnet *); 209 static void axe_ifmedia_sts(struct ifnet *, struct ifmediareq *); 210 static int axe_cmd(struct axe_softc *, int, int, int, void *); 211 static void axe_ax88178_init(struct axe_softc *); 212 static void axe_ax88772_init(struct axe_softc *); 213 static void axe_ax88772_phywake(struct axe_softc *); 214 static void axe_ax88772a_init(struct axe_softc *); 215 static void axe_ax88772b_init(struct axe_softc *); 216 static int axe_get_phyno(struct axe_softc *, int); 217 static int axe_ioctl(struct ifnet *, u_long, caddr_t); 218 static int axe_rx_frame(struct usb_ether *, struct usb_page_cache *, int); 219 static int axe_rxeof(struct usb_ether *, struct usb_page_cache *, 220 unsigned offset, unsigned, struct axe_csum_hdr *); 221 static void axe_csum_cfg(struct usb_ether *); 222 223 static const struct usb_config axe_config[AXE_N_TRANSFER] = { 224 [AXE_BULK_DT_WR] = { 225 .type = UE_BULK, 226 .endpoint = UE_ADDR_ANY, 227 .direction = UE_DIR_OUT, 228 .frames = 16, 229 .bufsize = 16 * MCLBYTES, 230 .flags = {.pipe_bof = 1,.force_short_xfer = 1,}, 231 .callback = axe_bulk_write_callback, 232 .timeout = 10000, /* 10 seconds */ 233 }, 234 235 [AXE_BULK_DT_RD] = { 236 .type = UE_BULK, 237 .endpoint = UE_ADDR_ANY, 238 .direction = UE_DIR_IN, 239 .bufsize = 16384, /* bytes */ 240 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, 241 .callback = axe_bulk_read_callback, 242 .timeout = 0, /* no timeout */ 243 }, 244 }; 245 246 static const struct ax88772b_mfb ax88772b_mfb_table[] = { 247 { 0x8000, 0x8001, 2048 }, 248 { 0x8100, 0x8147, 4096}, 249 { 0x8200, 0x81EB, 6144}, 250 { 0x8300, 0x83D7, 8192}, 251 { 0x8400, 0x851E, 16384}, 252 { 0x8500, 0x8666, 20480}, 253 { 0x8600, 0x87AE, 24576}, 254 { 0x8700, 0x8A3D, 32768} 255 }; 256 257 static device_method_t axe_methods[] = { 258 /* Device interface */ 259 DEVMETHOD(device_probe, axe_probe), 260 DEVMETHOD(device_attach, axe_attach), 261 DEVMETHOD(device_detach, axe_detach), 262 263 /* MII interface */ 264 DEVMETHOD(miibus_readreg, axe_miibus_readreg), 265 DEVMETHOD(miibus_writereg, axe_miibus_writereg), 266 DEVMETHOD(miibus_statchg, axe_miibus_statchg), 267 268 DEVMETHOD_END 269 }; 270 271 static driver_t axe_driver = { 272 .name = "axe", 273 .methods = axe_methods, 274 .size = sizeof(struct axe_softc), 275 }; 276 277 DRIVER_MODULE(axe, uhub, axe_driver, NULL, NULL); 278 DRIVER_MODULE(miibus, axe, miibus_driver, 0, 0); 279 MODULE_DEPEND(axe, uether, 1, 1, 1); 280 MODULE_DEPEND(axe, usb, 1, 1, 1); 281 MODULE_DEPEND(axe, ether, 1, 1, 1); 282 MODULE_DEPEND(axe, miibus, 1, 1, 1); 283 MODULE_VERSION(axe, 1); 284 USB_PNP_HOST_INFO(axe_devs); 285 286 static const struct usb_ether_methods axe_ue_methods = { 287 .ue_attach_post = axe_attach_post, 288 .ue_attach_post_sub = axe_attach_post_sub, 289 .ue_start = axe_start, 290 .ue_init = axe_init, 291 .ue_stop = axe_stop, 292 .ue_tick = axe_tick, 293 .ue_setmulti = axe_setmulti, 294 .ue_setpromisc = axe_setpromisc, 295 .ue_mii_upd = axe_ifmedia_upd, 296 .ue_mii_sts = axe_ifmedia_sts, 297 }; 298 299 static int 300 axe_cmd(struct axe_softc *sc, int cmd, int index, int val, void *buf) 301 { 302 struct usb_device_request req; 303 usb_error_t err; 304 305 AXE_LOCK_ASSERT(sc, MA_OWNED); 306 307 req.bmRequestType = (AXE_CMD_IS_WRITE(cmd) ? 308 UT_WRITE_VENDOR_DEVICE : 309 UT_READ_VENDOR_DEVICE); 310 req.bRequest = AXE_CMD_CMD(cmd); 311 USETW(req.wValue, val); 312 USETW(req.wIndex, index); 313 USETW(req.wLength, AXE_CMD_LEN(cmd)); 314 315 err = uether_do_request(&sc->sc_ue, &req, buf, 1000); 316 317 return (err); 318 } 319 320 static int 321 axe_miibus_readreg(device_t dev, int phy, int reg) 322 { 323 struct axe_softc *sc = device_get_softc(dev); 324 uint16_t val; 325 int locked; 326 327 locked = mtx_owned(&sc->sc_mtx); 328 if (!locked) 329 AXE_LOCK(sc); 330 331 axe_cmd(sc, AXE_CMD_MII_OPMODE_SW, 0, 0, NULL); 332 axe_cmd(sc, AXE_CMD_MII_READ_REG, reg, phy, &val); 333 axe_cmd(sc, AXE_CMD_MII_OPMODE_HW, 0, 0, NULL); 334 335 val = le16toh(val); 336 if (AXE_IS_772(sc) && reg == MII_BMSR) { 337 /* 338 * BMSR of AX88772 indicates that it supports extended 339 * capability but the extended status register is 340 * revered for embedded ethernet PHY. So clear the 341 * extended capability bit of BMSR. 342 */ 343 val &= ~BMSR_EXTCAP; 344 } 345 346 if (!locked) 347 AXE_UNLOCK(sc); 348 return (val); 349 } 350 351 static int 352 axe_miibus_writereg(device_t dev, int phy, int reg, int val) 353 { 354 struct axe_softc *sc = device_get_softc(dev); 355 int locked; 356 357 val = htole32(val); 358 locked = mtx_owned(&sc->sc_mtx); 359 if (!locked) 360 AXE_LOCK(sc); 361 362 axe_cmd(sc, AXE_CMD_MII_OPMODE_SW, 0, 0, NULL); 363 axe_cmd(sc, AXE_CMD_MII_WRITE_REG, reg, phy, &val); 364 axe_cmd(sc, AXE_CMD_MII_OPMODE_HW, 0, 0, NULL); 365 366 if (!locked) 367 AXE_UNLOCK(sc); 368 return (0); 369 } 370 371 static void 372 axe_miibus_statchg(device_t dev) 373 { 374 struct axe_softc *sc = device_get_softc(dev); 375 struct mii_data *mii = GET_MII(sc); 376 struct ifnet *ifp; 377 uint16_t val; 378 int err, locked; 379 380 locked = mtx_owned(&sc->sc_mtx); 381 if (!locked) 382 AXE_LOCK(sc); 383 384 ifp = uether_getifp(&sc->sc_ue); 385 if (mii == NULL || ifp == NULL || 386 (ifp->if_drv_flags & IFF_DRV_RUNNING) == 0) 387 goto done; 388 389 sc->sc_flags &= ~AXE_FLAG_LINK; 390 if ((mii->mii_media_status & (IFM_ACTIVE | IFM_AVALID)) == 391 (IFM_ACTIVE | IFM_AVALID)) { 392 switch (IFM_SUBTYPE(mii->mii_media_active)) { 393 case IFM_10_T: 394 case IFM_100_TX: 395 sc->sc_flags |= AXE_FLAG_LINK; 396 break; 397 case IFM_1000_T: 398 if ((sc->sc_flags & AXE_FLAG_178) == 0) 399 break; 400 sc->sc_flags |= AXE_FLAG_LINK; 401 break; 402 default: 403 break; 404 } 405 } 406 407 /* Lost link, do nothing. */ 408 if ((sc->sc_flags & AXE_FLAG_LINK) == 0) 409 goto done; 410 411 val = 0; 412 if ((IFM_OPTIONS(mii->mii_media_active) & IFM_FDX) != 0) { 413 val |= AXE_MEDIA_FULL_DUPLEX; 414 if (AXE_IS_178_FAMILY(sc)) { 415 if ((IFM_OPTIONS(mii->mii_media_active) & 416 IFM_ETH_TXPAUSE) != 0) 417 val |= AXE_178_MEDIA_TXFLOW_CONTROL_EN; 418 if ((IFM_OPTIONS(mii->mii_media_active) & 419 IFM_ETH_RXPAUSE) != 0) 420 val |= AXE_178_MEDIA_RXFLOW_CONTROL_EN; 421 } 422 } 423 if (AXE_IS_178_FAMILY(sc)) { 424 val |= AXE_178_MEDIA_RX_EN | AXE_178_MEDIA_MAGIC; 425 if ((sc->sc_flags & AXE_FLAG_178) != 0) 426 val |= AXE_178_MEDIA_ENCK; 427 switch (IFM_SUBTYPE(mii->mii_media_active)) { 428 case IFM_1000_T: 429 val |= AXE_178_MEDIA_GMII | AXE_178_MEDIA_ENCK; 430 break; 431 case IFM_100_TX: 432 val |= AXE_178_MEDIA_100TX; 433 break; 434 case IFM_10_T: 435 /* doesn't need to be handled */ 436 break; 437 } 438 } 439 err = axe_cmd(sc, AXE_CMD_WRITE_MEDIA, 0, val, NULL); 440 if (err) 441 device_printf(dev, "media change failed, error %d\n", err); 442 done: 443 if (!locked) 444 AXE_UNLOCK(sc); 445 } 446 447 /* 448 * Set media options. 449 */ 450 static int 451 axe_ifmedia_upd(struct ifnet *ifp) 452 { 453 struct axe_softc *sc = ifp->if_softc; 454 struct mii_data *mii = GET_MII(sc); 455 struct mii_softc *miisc; 456 int error; 457 458 AXE_LOCK_ASSERT(sc, MA_OWNED); 459 460 LIST_FOREACH(miisc, &mii->mii_phys, mii_list) 461 PHY_RESET(miisc); 462 error = mii_mediachg(mii); 463 return (error); 464 } 465 466 /* 467 * Report current media status. 468 */ 469 static void 470 axe_ifmedia_sts(struct ifnet *ifp, struct ifmediareq *ifmr) 471 { 472 struct axe_softc *sc = ifp->if_softc; 473 struct mii_data *mii = GET_MII(sc); 474 475 AXE_LOCK(sc); 476 mii_pollstat(mii); 477 ifmr->ifm_active = mii->mii_media_active; 478 ifmr->ifm_status = mii->mii_media_status; 479 AXE_UNLOCK(sc); 480 } 481 482 static u_int 483 axe_hash_maddr(void *arg, struct sockaddr_dl *sdl, u_int cnt) 484 { 485 uint8_t *hashtbl = arg; 486 uint32_t h; 487 488 h = ether_crc32_be(LLADDR(sdl), ETHER_ADDR_LEN) >> 26; 489 hashtbl[h / 8] |= 1 << (h % 8); 490 491 return (1); 492 } 493 494 static void 495 axe_setmulti(struct usb_ether *ue) 496 { 497 struct axe_softc *sc = uether_getsc(ue); 498 struct ifnet *ifp = uether_getifp(ue); 499 uint16_t rxmode; 500 uint8_t hashtbl[8] = { 0, 0, 0, 0, 0, 0, 0, 0 }; 501 502 AXE_LOCK_ASSERT(sc, MA_OWNED); 503 504 axe_cmd(sc, AXE_CMD_RXCTL_READ, 0, 0, &rxmode); 505 rxmode = le16toh(rxmode); 506 507 if (ifp->if_flags & (IFF_ALLMULTI | IFF_PROMISC)) { 508 rxmode |= AXE_RXCMD_ALLMULTI; 509 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, rxmode, NULL); 510 return; 511 } 512 rxmode &= ~AXE_RXCMD_ALLMULTI; 513 514 if_foreach_llmaddr(ifp, axe_hash_maddr, &hashtbl); 515 516 axe_cmd(sc, AXE_CMD_WRITE_MCAST, 0, 0, (void *)&hashtbl); 517 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, rxmode, NULL); 518 } 519 520 static int 521 axe_get_phyno(struct axe_softc *sc, int sel) 522 { 523 int phyno; 524 525 switch (AXE_PHY_TYPE(sc->sc_phyaddrs[sel])) { 526 case PHY_TYPE_100_HOME: 527 case PHY_TYPE_GIG: 528 phyno = AXE_PHY_NO(sc->sc_phyaddrs[sel]); 529 break; 530 case PHY_TYPE_SPECIAL: 531 /* FALLTHROUGH */ 532 case PHY_TYPE_RSVD: 533 /* FALLTHROUGH */ 534 case PHY_TYPE_NON_SUP: 535 /* FALLTHROUGH */ 536 default: 537 phyno = -1; 538 break; 539 } 540 541 return (phyno); 542 } 543 544 #define AXE_GPIO_WRITE(x, y) do { \ 545 axe_cmd(sc, AXE_CMD_WRITE_GPIO, 0, (x), NULL); \ 546 uether_pause(ue, (y)); \ 547 } while (0) 548 549 static void 550 axe_ax88178_init(struct axe_softc *sc) 551 { 552 struct usb_ether *ue; 553 int gpio0, ledmode, phymode; 554 uint16_t eeprom, val; 555 556 ue = &sc->sc_ue; 557 axe_cmd(sc, AXE_CMD_SROM_WR_ENABLE, 0, 0, NULL); 558 /* XXX magic */ 559 axe_cmd(sc, AXE_CMD_SROM_READ, 0, 0x0017, &eeprom); 560 eeprom = le16toh(eeprom); 561 axe_cmd(sc, AXE_CMD_SROM_WR_DISABLE, 0, 0, NULL); 562 563 /* if EEPROM is invalid we have to use to GPIO0 */ 564 if (eeprom == 0xffff) { 565 phymode = AXE_PHY_MODE_MARVELL; 566 gpio0 = 1; 567 ledmode = 0; 568 } else { 569 phymode = eeprom & 0x7f; 570 gpio0 = (eeprom & 0x80) ? 0 : 1; 571 ledmode = eeprom >> 8; 572 } 573 574 if (bootverbose) 575 device_printf(sc->sc_ue.ue_dev, 576 "EEPROM data : 0x%04x, phymode : 0x%02x\n", eeprom, 577 phymode); 578 /* Program GPIOs depending on PHY hardware. */ 579 switch (phymode) { 580 case AXE_PHY_MODE_MARVELL: 581 if (gpio0 == 1) { 582 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM | AXE_GPIO0_EN, 583 hz / 32); 584 AXE_GPIO_WRITE(AXE_GPIO0_EN | AXE_GPIO2 | AXE_GPIO2_EN, 585 hz / 32); 586 AXE_GPIO_WRITE(AXE_GPIO0_EN | AXE_GPIO2_EN, hz / 4); 587 AXE_GPIO_WRITE(AXE_GPIO0_EN | AXE_GPIO2 | AXE_GPIO2_EN, 588 hz / 32); 589 } else { 590 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM | AXE_GPIO1 | 591 AXE_GPIO1_EN, hz / 3); 592 if (ledmode == 1) { 593 AXE_GPIO_WRITE(AXE_GPIO1_EN, hz / 3); 594 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN, 595 hz / 3); 596 } else { 597 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | 598 AXE_GPIO2 | AXE_GPIO2_EN, hz / 32); 599 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | 600 AXE_GPIO2_EN, hz / 4); 601 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | 602 AXE_GPIO2 | AXE_GPIO2_EN, hz / 32); 603 } 604 } 605 break; 606 case AXE_PHY_MODE_CICADA: 607 case AXE_PHY_MODE_CICADA_V2: 608 case AXE_PHY_MODE_CICADA_V2_ASIX: 609 if (gpio0 == 1) 610 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM | AXE_GPIO0 | 611 AXE_GPIO0_EN, hz / 32); 612 else 613 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM | AXE_GPIO1 | 614 AXE_GPIO1_EN, hz / 32); 615 break; 616 case AXE_PHY_MODE_AGERE: 617 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM | AXE_GPIO1 | 618 AXE_GPIO1_EN, hz / 32); 619 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | AXE_GPIO2 | 620 AXE_GPIO2_EN, hz / 32); 621 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | AXE_GPIO2_EN, hz / 4); 622 AXE_GPIO_WRITE(AXE_GPIO1 | AXE_GPIO1_EN | AXE_GPIO2 | 623 AXE_GPIO2_EN, hz / 32); 624 break; 625 case AXE_PHY_MODE_REALTEK_8211CL: 626 case AXE_PHY_MODE_REALTEK_8211BN: 627 case AXE_PHY_MODE_REALTEK_8251CL: 628 val = gpio0 == 1 ? AXE_GPIO0 | AXE_GPIO0_EN : 629 AXE_GPIO1 | AXE_GPIO1_EN; 630 AXE_GPIO_WRITE(val, hz / 32); 631 AXE_GPIO_WRITE(val | AXE_GPIO2 | AXE_GPIO2_EN, hz / 32); 632 AXE_GPIO_WRITE(val | AXE_GPIO2_EN, hz / 4); 633 AXE_GPIO_WRITE(val | AXE_GPIO2 | AXE_GPIO2_EN, hz / 32); 634 if (phymode == AXE_PHY_MODE_REALTEK_8211CL) { 635 axe_miibus_writereg(ue->ue_dev, sc->sc_phyno, 636 0x1F, 0x0005); 637 axe_miibus_writereg(ue->ue_dev, sc->sc_phyno, 638 0x0C, 0x0000); 639 val = axe_miibus_readreg(ue->ue_dev, sc->sc_phyno, 640 0x0001); 641 axe_miibus_writereg(ue->ue_dev, sc->sc_phyno, 642 0x01, val | 0x0080); 643 axe_miibus_writereg(ue->ue_dev, sc->sc_phyno, 644 0x1F, 0x0000); 645 } 646 break; 647 default: 648 /* Unknown PHY model or no need to program GPIOs. */ 649 break; 650 } 651 652 /* soft reset */ 653 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_CLEAR, NULL); 654 uether_pause(ue, hz / 4); 655 656 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, 657 AXE_SW_RESET_PRL | AXE_178_RESET_MAGIC, NULL); 658 uether_pause(ue, hz / 4); 659 /* Enable MII/GMII/RGMII interface to work with external PHY. */ 660 axe_cmd(sc, AXE_CMD_SW_PHY_SELECT, 0, 0, NULL); 661 uether_pause(ue, hz / 4); 662 663 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, 0, NULL); 664 } 665 666 static void 667 axe_ax88772_init(struct axe_softc *sc) 668 { 669 axe_cmd(sc, AXE_CMD_WRITE_GPIO, 0, 0x00b0, NULL); 670 uether_pause(&sc->sc_ue, hz / 16); 671 672 if (sc->sc_phyno == AXE_772_PHY_NO_EPHY) { 673 /* ask for the embedded PHY */ 674 axe_cmd(sc, AXE_CMD_SW_PHY_SELECT, 0, 0x01, NULL); 675 uether_pause(&sc->sc_ue, hz / 64); 676 677 /* power down and reset state, pin reset state */ 678 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, 679 AXE_SW_RESET_CLEAR, NULL); 680 uether_pause(&sc->sc_ue, hz / 16); 681 682 /* power down/reset state, pin operating state */ 683 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, 684 AXE_SW_RESET_IPPD | AXE_SW_RESET_PRL, NULL); 685 uether_pause(&sc->sc_ue, hz / 4); 686 687 /* power up, reset */ 688 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_PRL, NULL); 689 690 /* power up, operating */ 691 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, 692 AXE_SW_RESET_IPRL | AXE_SW_RESET_PRL, NULL); 693 } else { 694 /* ask for external PHY */ 695 axe_cmd(sc, AXE_CMD_SW_PHY_SELECT, 0, 0x00, NULL); 696 uether_pause(&sc->sc_ue, hz / 64); 697 698 /* power down internal PHY */ 699 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, 700 AXE_SW_RESET_IPPD | AXE_SW_RESET_PRL, NULL); 701 } 702 703 uether_pause(&sc->sc_ue, hz / 4); 704 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, 0, NULL); 705 } 706 707 static void 708 axe_ax88772_phywake(struct axe_softc *sc) 709 { 710 if (sc->sc_phyno == AXE_772_PHY_NO_EPHY) { 711 /* Manually select internal(embedded) PHY - MAC mode. */ 712 axe_cmd(sc, AXE_CMD_SW_PHY_SELECT, 0, AXE_SW_PHY_SELECT_SS_ENB | 713 AXE_SW_PHY_SELECT_EMBEDDED | AXE_SW_PHY_SELECT_SS_MII, 714 NULL); 715 uether_pause(&sc->sc_ue, hz / 32); 716 } else { 717 /* 718 * Manually select external PHY - MAC mode. 719 * Reverse MII/RMII is for AX88772A PHY mode. 720 */ 721 axe_cmd(sc, AXE_CMD_SW_PHY_SELECT, 0, AXE_SW_PHY_SELECT_SS_ENB | 722 AXE_SW_PHY_SELECT_EXT | AXE_SW_PHY_SELECT_SS_MII, NULL); 723 uether_pause(&sc->sc_ue, hz / 32); 724 } 725 /* Take PHY out of power down. */ 726 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_IPPD | 727 AXE_SW_RESET_IPRL, NULL); 728 uether_pause(&sc->sc_ue, hz / 4); 729 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_IPRL, NULL); 730 uether_pause(&sc->sc_ue, hz); 731 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_CLEAR, NULL); 732 uether_pause(&sc->sc_ue, hz / 32); 733 axe_cmd(sc, AXE_CMD_SW_RESET_REG, 0, AXE_SW_RESET_IPRL, NULL); 734 uether_pause(&sc->sc_ue, hz / 32); 735 } 736 737 static void 738 axe_ax88772a_init(struct axe_softc *sc) 739 { 740 struct usb_ether *ue; 741 742 ue = &sc->sc_ue; 743 /* Reload EEPROM. */ 744 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM, hz / 32); 745 axe_ax88772_phywake(sc); 746 /* Stop MAC. */ 747 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, 0, NULL); 748 } 749 750 static void 751 axe_ax88772b_init(struct axe_softc *sc) 752 { 753 struct usb_ether *ue; 754 uint16_t eeprom; 755 uint8_t *eaddr; 756 int i; 757 758 ue = &sc->sc_ue; 759 /* Reload EEPROM. */ 760 AXE_GPIO_WRITE(AXE_GPIO_RELOAD_EEPROM, hz / 32); 761 /* 762 * Save PHY power saving configuration(high byte) and 763 * clear EEPROM checksum value(low byte). 764 */ 765 axe_cmd(sc, AXE_CMD_SROM_READ, 0, AXE_EEPROM_772B_PHY_PWRCFG, &eeprom); 766 sc->sc_pwrcfg = le16toh(eeprom) & 0xFF00; 767 768 /* 769 * Auto-loaded default station address from internal ROM is 770 * 00:00:00:00:00:00 such that an explicit access to EEPROM 771 * is required to get real station address. 772 */ 773 eaddr = ue->ue_eaddr; 774 for (i = 0; i < ETHER_ADDR_LEN / 2; i++) { 775 axe_cmd(sc, AXE_CMD_SROM_READ, 0, AXE_EEPROM_772B_NODE_ID + i, 776 &eeprom); 777 eeprom = le16toh(eeprom); 778 *eaddr++ = (uint8_t)(eeprom & 0xFF); 779 *eaddr++ = (uint8_t)((eeprom >> 8) & 0xFF); 780 } 781 /* Wakeup PHY. */ 782 axe_ax88772_phywake(sc); 783 /* Stop MAC. */ 784 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, 0, NULL); 785 } 786 787 #undef AXE_GPIO_WRITE 788 789 static void 790 axe_reset(struct axe_softc *sc) 791 { 792 struct usb_config_descriptor *cd; 793 usb_error_t err; 794 795 cd = usbd_get_config_descriptor(sc->sc_ue.ue_udev); 796 797 err = usbd_req_set_config(sc->sc_ue.ue_udev, &sc->sc_mtx, 798 cd->bConfigurationValue); 799 if (err) 800 DPRINTF("reset failed (ignored)\n"); 801 802 /* Wait a little while for the chip to get its brains in order. */ 803 uether_pause(&sc->sc_ue, hz / 100); 804 805 /* Reinitialize controller to achieve full reset. */ 806 if (sc->sc_flags & AXE_FLAG_178) 807 axe_ax88178_init(sc); 808 else if (sc->sc_flags & AXE_FLAG_772) 809 axe_ax88772_init(sc); 810 else if (sc->sc_flags & AXE_FLAG_772A) 811 axe_ax88772a_init(sc); 812 else if (sc->sc_flags & AXE_FLAG_772B) 813 axe_ax88772b_init(sc); 814 } 815 816 static void 817 axe_attach_post(struct usb_ether *ue) 818 { 819 struct axe_softc *sc = uether_getsc(ue); 820 821 /* 822 * Load PHY indexes first. Needed by axe_xxx_init(). 823 */ 824 axe_cmd(sc, AXE_CMD_READ_PHYID, 0, 0, sc->sc_phyaddrs); 825 if (bootverbose) 826 device_printf(sc->sc_ue.ue_dev, "PHYADDR 0x%02x:0x%02x\n", 827 sc->sc_phyaddrs[0], sc->sc_phyaddrs[1]); 828 sc->sc_phyno = axe_get_phyno(sc, AXE_PHY_SEL_PRI); 829 if (sc->sc_phyno == -1) 830 sc->sc_phyno = axe_get_phyno(sc, AXE_PHY_SEL_SEC); 831 if (sc->sc_phyno == -1) { 832 device_printf(sc->sc_ue.ue_dev, 833 "no valid PHY address found, assuming PHY address 0\n"); 834 sc->sc_phyno = 0; 835 } 836 837 /* Initialize controller and get station address. */ 838 if (sc->sc_flags & AXE_FLAG_178) { 839 axe_ax88178_init(sc); 840 axe_cmd(sc, AXE_178_CMD_READ_NODEID, 0, 0, ue->ue_eaddr); 841 } else if (sc->sc_flags & AXE_FLAG_772) { 842 axe_ax88772_init(sc); 843 axe_cmd(sc, AXE_178_CMD_READ_NODEID, 0, 0, ue->ue_eaddr); 844 } else if (sc->sc_flags & AXE_FLAG_772A) { 845 axe_ax88772a_init(sc); 846 axe_cmd(sc, AXE_178_CMD_READ_NODEID, 0, 0, ue->ue_eaddr); 847 } else if (sc->sc_flags & AXE_FLAG_772B) { 848 axe_ax88772b_init(sc); 849 } else 850 axe_cmd(sc, AXE_172_CMD_READ_NODEID, 0, 0, ue->ue_eaddr); 851 852 /* 853 * Fetch IPG values. 854 */ 855 if (sc->sc_flags & (AXE_FLAG_772A | AXE_FLAG_772B)) { 856 /* Set IPG values. */ 857 sc->sc_ipgs[0] = 0x15; 858 sc->sc_ipgs[1] = 0x16; 859 sc->sc_ipgs[2] = 0x1A; 860 } else 861 axe_cmd(sc, AXE_CMD_READ_IPG012, 0, 0, sc->sc_ipgs); 862 } 863 864 static int 865 axe_attach_post_sub(struct usb_ether *ue) 866 { 867 struct axe_softc *sc; 868 struct ifnet *ifp; 869 u_int adv_pause; 870 int error; 871 872 sc = uether_getsc(ue); 873 ifp = ue->ue_ifp; 874 ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; 875 ifp->if_start = uether_start; 876 ifp->if_ioctl = axe_ioctl; 877 ifp->if_init = uether_init; 878 IFQ_SET_MAXLEN(&ifp->if_snd, ifqmaxlen); 879 ifp->if_snd.ifq_drv_maxlen = ifqmaxlen; 880 IFQ_SET_READY(&ifp->if_snd); 881 882 if (AXE_IS_178_FAMILY(sc)) 883 ifp->if_capabilities |= IFCAP_VLAN_MTU; 884 if (sc->sc_flags & AXE_FLAG_772B) { 885 ifp->if_capabilities |= IFCAP_TXCSUM | IFCAP_RXCSUM; 886 ifp->if_hwassist = AXE_CSUM_FEATURES; 887 /* 888 * Checksum offloading of AX88772B also works with VLAN 889 * tagged frames but there is no way to take advantage 890 * of the feature because vlan(4) assumes 891 * IFCAP_VLAN_HWTAGGING is prerequisite condition to 892 * support checksum offloading with VLAN. VLAN hardware 893 * tagging support of AX88772B is very limited so it's 894 * not possible to announce IFCAP_VLAN_HWTAGGING. 895 */ 896 } 897 ifp->if_capenable = ifp->if_capabilities; 898 if (sc->sc_flags & (AXE_FLAG_772A | AXE_FLAG_772B | AXE_FLAG_178)) 899 adv_pause = MIIF_DOPAUSE; 900 else 901 adv_pause = 0; 902 bus_topo_lock(); 903 error = mii_attach(ue->ue_dev, &ue->ue_miibus, ifp, 904 uether_ifmedia_upd, ue->ue_methods->ue_mii_sts, 905 BMSR_DEFCAPMASK, sc->sc_phyno, MII_OFFSET_ANY, adv_pause); 906 bus_topo_unlock(); 907 908 return (error); 909 } 910 911 /* 912 * Probe for a AX88172 chip. 913 */ 914 static int 915 axe_probe(device_t dev) 916 { 917 struct usb_attach_arg *uaa = device_get_ivars(dev); 918 919 if (uaa->usb_mode != USB_MODE_HOST) 920 return (ENXIO); 921 if (uaa->info.bConfigIndex != AXE_CONFIG_IDX) 922 return (ENXIO); 923 if (uaa->info.bIfaceIndex != AXE_IFACE_IDX) 924 return (ENXIO); 925 926 return (usbd_lookup_id_by_uaa(axe_devs, sizeof(axe_devs), uaa)); 927 } 928 929 /* 930 * Attach the interface. Allocate softc structures, do ifmedia 931 * setup and ethernet/BPF attach. 932 */ 933 static int 934 axe_attach(device_t dev) 935 { 936 struct usb_attach_arg *uaa = device_get_ivars(dev); 937 struct axe_softc *sc = device_get_softc(dev); 938 struct usb_ether *ue = &sc->sc_ue; 939 uint8_t iface_index; 940 int error; 941 942 sc->sc_flags = USB_GET_DRIVER_INFO(uaa); 943 944 device_set_usb_desc(dev); 945 946 mtx_init(&sc->sc_mtx, device_get_nameunit(dev), NULL, MTX_DEF); 947 948 iface_index = AXE_IFACE_IDX; 949 error = usbd_transfer_setup(uaa->device, &iface_index, sc->sc_xfer, 950 axe_config, AXE_N_TRANSFER, sc, &sc->sc_mtx); 951 if (error) { 952 device_printf(dev, "allocating USB transfers failed\n"); 953 goto detach; 954 } 955 956 ue->ue_sc = sc; 957 ue->ue_dev = dev; 958 ue->ue_udev = uaa->device; 959 ue->ue_mtx = &sc->sc_mtx; 960 ue->ue_methods = &axe_ue_methods; 961 962 error = uether_ifattach(ue); 963 if (error) { 964 device_printf(dev, "could not attach interface\n"); 965 goto detach; 966 } 967 return (0); /* success */ 968 969 detach: 970 axe_detach(dev); 971 return (ENXIO); /* failure */ 972 } 973 974 static int 975 axe_detach(device_t dev) 976 { 977 struct axe_softc *sc = device_get_softc(dev); 978 struct usb_ether *ue = &sc->sc_ue; 979 980 usbd_transfer_unsetup(sc->sc_xfer, AXE_N_TRANSFER); 981 uether_ifdetach(ue); 982 mtx_destroy(&sc->sc_mtx); 983 984 return (0); 985 } 986 987 #if (AXE_BULK_BUF_SIZE >= 0x10000) 988 #error "Please update axe_bulk_read_callback()!" 989 #endif 990 991 static void 992 axe_bulk_read_callback(struct usb_xfer *xfer, usb_error_t error) 993 { 994 struct axe_softc *sc = usbd_xfer_softc(xfer); 995 struct usb_ether *ue = &sc->sc_ue; 996 struct usb_page_cache *pc; 997 int actlen; 998 999 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); 1000 1001 switch (USB_GET_STATE(xfer)) { 1002 case USB_ST_TRANSFERRED: 1003 pc = usbd_xfer_get_frame(xfer, 0); 1004 axe_rx_frame(ue, pc, actlen); 1005 1006 /* FALLTHROUGH */ 1007 case USB_ST_SETUP: 1008 tr_setup: 1009 usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); 1010 usbd_transfer_submit(xfer); 1011 uether_rxflush(ue); 1012 return; 1013 1014 default: /* Error */ 1015 DPRINTF("bulk read error, %s\n", usbd_errstr(error)); 1016 1017 if (error != USB_ERR_CANCELLED) { 1018 /* try to clear stall first */ 1019 usbd_xfer_set_stall(xfer); 1020 goto tr_setup; 1021 } 1022 return; 1023 } 1024 } 1025 1026 static int 1027 axe_rx_frame(struct usb_ether *ue, struct usb_page_cache *pc, int actlen) 1028 { 1029 struct axe_softc *sc; 1030 struct axe_sframe_hdr hdr; 1031 struct axe_csum_hdr csum_hdr; 1032 int error, len, pos; 1033 1034 sc = uether_getsc(ue); 1035 pos = 0; 1036 len = 0; 1037 error = 0; 1038 if ((sc->sc_flags & AXE_FLAG_STD_FRAME) != 0) { 1039 while (pos < actlen) { 1040 if ((int)(pos + sizeof(hdr)) > actlen) { 1041 /* too little data */ 1042 error = EINVAL; 1043 break; 1044 } 1045 usbd_copy_out(pc, pos, &hdr, sizeof(hdr)); 1046 1047 if ((hdr.len ^ hdr.ilen) != sc->sc_lenmask) { 1048 /* we lost sync */ 1049 error = EINVAL; 1050 break; 1051 } 1052 pos += sizeof(hdr); 1053 len = le16toh(hdr.len); 1054 if (pos + len > actlen) { 1055 /* invalid length */ 1056 error = EINVAL; 1057 break; 1058 } 1059 axe_rxeof(ue, pc, pos, len, NULL); 1060 pos += len + (len % 2); 1061 } 1062 } else if ((sc->sc_flags & AXE_FLAG_CSUM_FRAME) != 0) { 1063 while (pos < actlen) { 1064 if ((int)(pos + sizeof(csum_hdr)) > actlen) { 1065 /* too little data */ 1066 error = EINVAL; 1067 break; 1068 } 1069 usbd_copy_out(pc, pos, &csum_hdr, sizeof(csum_hdr)); 1070 1071 csum_hdr.len = le16toh(csum_hdr.len); 1072 csum_hdr.ilen = le16toh(csum_hdr.ilen); 1073 csum_hdr.cstatus = le16toh(csum_hdr.cstatus); 1074 if ((AXE_CSUM_RXBYTES(csum_hdr.len) ^ 1075 AXE_CSUM_RXBYTES(csum_hdr.ilen)) != 1076 sc->sc_lenmask) { 1077 /* we lost sync */ 1078 error = EINVAL; 1079 break; 1080 } 1081 /* 1082 * Get total transferred frame length including 1083 * checksum header. The length should be multiple 1084 * of 4. 1085 */ 1086 len = sizeof(csum_hdr) + AXE_CSUM_RXBYTES(csum_hdr.len); 1087 len = (len + 3) & ~3; 1088 if (pos + len > actlen) { 1089 /* invalid length */ 1090 error = EINVAL; 1091 break; 1092 } 1093 axe_rxeof(ue, pc, pos + sizeof(csum_hdr), 1094 AXE_CSUM_RXBYTES(csum_hdr.len), &csum_hdr); 1095 pos += len; 1096 } 1097 } else 1098 axe_rxeof(ue, pc, 0, actlen, NULL); 1099 1100 if (error != 0) 1101 if_inc_counter(ue->ue_ifp, IFCOUNTER_IERRORS, 1); 1102 return (error); 1103 } 1104 1105 static int 1106 axe_rxeof(struct usb_ether *ue, struct usb_page_cache *pc, unsigned offset, 1107 unsigned len, struct axe_csum_hdr *csum_hdr) 1108 { 1109 struct ifnet *ifp = ue->ue_ifp; 1110 struct mbuf *m; 1111 1112 if (len < ETHER_HDR_LEN || len > MCLBYTES - ETHER_ALIGN) { 1113 if_inc_counter(ifp, IFCOUNTER_IERRORS, 1); 1114 return (EINVAL); 1115 } 1116 1117 m = m_getcl(M_NOWAIT, MT_DATA, M_PKTHDR); 1118 if (m == NULL) { 1119 if_inc_counter(ifp, IFCOUNTER_IQDROPS, 1); 1120 return (ENOMEM); 1121 } 1122 m->m_len = m->m_pkthdr.len = MCLBYTES; 1123 m_adj(m, ETHER_ALIGN); 1124 1125 usbd_copy_out(pc, offset, mtod(m, uint8_t *), len); 1126 1127 if_inc_counter(ifp, IFCOUNTER_IPACKETS, 1); 1128 m->m_pkthdr.rcvif = ifp; 1129 m->m_pkthdr.len = m->m_len = len; 1130 1131 if (csum_hdr != NULL && csum_hdr->cstatus & AXE_CSUM_HDR_L3_TYPE_IPV4) { 1132 if ((csum_hdr->cstatus & (AXE_CSUM_HDR_L4_CSUM_ERR | 1133 AXE_CSUM_HDR_L3_CSUM_ERR)) == 0) { 1134 m->m_pkthdr.csum_flags |= CSUM_IP_CHECKED | 1135 CSUM_IP_VALID; 1136 if ((csum_hdr->cstatus & AXE_CSUM_HDR_L4_TYPE_MASK) == 1137 AXE_CSUM_HDR_L4_TYPE_TCP || 1138 (csum_hdr->cstatus & AXE_CSUM_HDR_L4_TYPE_MASK) == 1139 AXE_CSUM_HDR_L4_TYPE_UDP) { 1140 m->m_pkthdr.csum_flags |= 1141 CSUM_DATA_VALID | CSUM_PSEUDO_HDR; 1142 m->m_pkthdr.csum_data = 0xffff; 1143 } 1144 } 1145 } 1146 1147 (void)mbufq_enqueue(&ue->ue_rxq, m); 1148 return (0); 1149 } 1150 1151 #if ((AXE_BULK_BUF_SIZE >= 0x10000) || (AXE_BULK_BUF_SIZE < (MCLBYTES+4))) 1152 #error "Please update axe_bulk_write_callback()!" 1153 #endif 1154 1155 static void 1156 axe_bulk_write_callback(struct usb_xfer *xfer, usb_error_t error) 1157 { 1158 struct axe_softc *sc = usbd_xfer_softc(xfer); 1159 struct axe_sframe_hdr hdr; 1160 struct ifnet *ifp = uether_getifp(&sc->sc_ue); 1161 struct usb_page_cache *pc; 1162 struct mbuf *m; 1163 int nframes, pos; 1164 1165 switch (USB_GET_STATE(xfer)) { 1166 case USB_ST_TRANSFERRED: 1167 DPRINTFN(11, "transfer complete\n"); 1168 ifp->if_drv_flags &= ~IFF_DRV_OACTIVE; 1169 /* FALLTHROUGH */ 1170 case USB_ST_SETUP: 1171 tr_setup: 1172 if ((sc->sc_flags & AXE_FLAG_LINK) == 0 || 1173 (ifp->if_drv_flags & IFF_DRV_OACTIVE) != 0) { 1174 /* 1175 * Don't send anything if there is no link or 1176 * controller is busy. 1177 */ 1178 return; 1179 } 1180 1181 for (nframes = 0; nframes < 16 && 1182 !IFQ_DRV_IS_EMPTY(&ifp->if_snd); nframes++) { 1183 IFQ_DRV_DEQUEUE(&ifp->if_snd, m); 1184 if (m == NULL) 1185 break; 1186 usbd_xfer_set_frame_offset(xfer, nframes * MCLBYTES, 1187 nframes); 1188 pos = 0; 1189 pc = usbd_xfer_get_frame(xfer, nframes); 1190 if (AXE_IS_178_FAMILY(sc)) { 1191 hdr.len = htole16(m->m_pkthdr.len); 1192 hdr.ilen = ~hdr.len; 1193 /* 1194 * If upper stack computed checksum, driver 1195 * should tell controller not to insert 1196 * computed checksum for checksum offloading 1197 * enabled controller. 1198 */ 1199 if (ifp->if_capabilities & IFCAP_TXCSUM) { 1200 if ((m->m_pkthdr.csum_flags & 1201 AXE_CSUM_FEATURES) != 0) 1202 hdr.len |= htole16( 1203 AXE_TX_CSUM_PSEUDO_HDR); 1204 else 1205 hdr.len |= htole16( 1206 AXE_TX_CSUM_DIS); 1207 } 1208 usbd_copy_in(pc, pos, &hdr, sizeof(hdr)); 1209 pos += sizeof(hdr); 1210 usbd_m_copy_in(pc, pos, m, 0, m->m_pkthdr.len); 1211 pos += m->m_pkthdr.len; 1212 if ((pos % 512) == 0) { 1213 hdr.len = 0; 1214 hdr.ilen = 0xffff; 1215 usbd_copy_in(pc, pos, &hdr, 1216 sizeof(hdr)); 1217 pos += sizeof(hdr); 1218 } 1219 } else { 1220 usbd_m_copy_in(pc, pos, m, 0, m->m_pkthdr.len); 1221 pos += m->m_pkthdr.len; 1222 } 1223 1224 /* 1225 * XXX 1226 * Update TX packet counter here. This is not 1227 * correct way but it seems that there is no way 1228 * to know how many packets are sent at the end 1229 * of transfer because controller combines 1230 * multiple writes into single one if there is 1231 * room in TX buffer of controller. 1232 */ 1233 if_inc_counter(ifp, IFCOUNTER_OPACKETS, 1); 1234 1235 /* 1236 * if there's a BPF listener, bounce a copy 1237 * of this frame to him: 1238 */ 1239 BPF_MTAP(ifp, m); 1240 1241 m_freem(m); 1242 1243 /* Set frame length. */ 1244 usbd_xfer_set_frame_len(xfer, nframes, pos); 1245 } 1246 if (nframes != 0) { 1247 usbd_xfer_set_frames(xfer, nframes); 1248 usbd_transfer_submit(xfer); 1249 ifp->if_drv_flags |= IFF_DRV_OACTIVE; 1250 } 1251 return; 1252 /* NOTREACHED */ 1253 default: /* Error */ 1254 DPRINTFN(11, "transfer error, %s\n", 1255 usbd_errstr(error)); 1256 1257 if_inc_counter(ifp, IFCOUNTER_OERRORS, 1); 1258 ifp->if_drv_flags &= ~IFF_DRV_OACTIVE; 1259 1260 if (error != USB_ERR_CANCELLED) { 1261 /* try to clear stall first */ 1262 usbd_xfer_set_stall(xfer); 1263 goto tr_setup; 1264 } 1265 return; 1266 } 1267 } 1268 1269 static void 1270 axe_tick(struct usb_ether *ue) 1271 { 1272 struct axe_softc *sc = uether_getsc(ue); 1273 struct mii_data *mii = GET_MII(sc); 1274 1275 AXE_LOCK_ASSERT(sc, MA_OWNED); 1276 1277 mii_tick(mii); 1278 if ((sc->sc_flags & AXE_FLAG_LINK) == 0) { 1279 axe_miibus_statchg(ue->ue_dev); 1280 if ((sc->sc_flags & AXE_FLAG_LINK) != 0) 1281 axe_start(ue); 1282 } 1283 } 1284 1285 static void 1286 axe_start(struct usb_ether *ue) 1287 { 1288 struct axe_softc *sc = uether_getsc(ue); 1289 1290 /* 1291 * start the USB transfers, if not already started: 1292 */ 1293 usbd_transfer_start(sc->sc_xfer[AXE_BULK_DT_RD]); 1294 usbd_transfer_start(sc->sc_xfer[AXE_BULK_DT_WR]); 1295 } 1296 1297 static void 1298 axe_csum_cfg(struct usb_ether *ue) 1299 { 1300 struct axe_softc *sc; 1301 struct ifnet *ifp; 1302 uint16_t csum1, csum2; 1303 1304 sc = uether_getsc(ue); 1305 AXE_LOCK_ASSERT(sc, MA_OWNED); 1306 1307 if ((sc->sc_flags & AXE_FLAG_772B) != 0) { 1308 ifp = uether_getifp(ue); 1309 csum1 = 0; 1310 csum2 = 0; 1311 if ((ifp->if_capenable & IFCAP_TXCSUM) != 0) 1312 csum1 |= AXE_TXCSUM_IP | AXE_TXCSUM_TCP | 1313 AXE_TXCSUM_UDP; 1314 axe_cmd(sc, AXE_772B_CMD_WRITE_TXCSUM, csum2, csum1, NULL); 1315 csum1 = 0; 1316 csum2 = 0; 1317 if ((ifp->if_capenable & IFCAP_RXCSUM) != 0) 1318 csum1 |= AXE_RXCSUM_IP | AXE_RXCSUM_IPVE | 1319 AXE_RXCSUM_TCP | AXE_RXCSUM_UDP | AXE_RXCSUM_ICMP | 1320 AXE_RXCSUM_IGMP; 1321 axe_cmd(sc, AXE_772B_CMD_WRITE_RXCSUM, csum2, csum1, NULL); 1322 } 1323 } 1324 1325 static void 1326 axe_init(struct usb_ether *ue) 1327 { 1328 struct axe_softc *sc = uether_getsc(ue); 1329 struct ifnet *ifp = uether_getifp(ue); 1330 uint16_t rxmode; 1331 1332 AXE_LOCK_ASSERT(sc, MA_OWNED); 1333 1334 if ((ifp->if_drv_flags & IFF_DRV_RUNNING) != 0) 1335 return; 1336 1337 /* Cancel pending I/O */ 1338 axe_stop(ue); 1339 1340 axe_reset(sc); 1341 1342 /* Set MAC address and transmitter IPG values. */ 1343 if (AXE_IS_178_FAMILY(sc)) { 1344 axe_cmd(sc, AXE_178_CMD_WRITE_NODEID, 0, 0, IF_LLADDR(ifp)); 1345 axe_cmd(sc, AXE_178_CMD_WRITE_IPG012, sc->sc_ipgs[2], 1346 (sc->sc_ipgs[1] << 8) | (sc->sc_ipgs[0]), NULL); 1347 } else { 1348 axe_cmd(sc, AXE_172_CMD_WRITE_NODEID, 0, 0, IF_LLADDR(ifp)); 1349 axe_cmd(sc, AXE_172_CMD_WRITE_IPG0, 0, sc->sc_ipgs[0], NULL); 1350 axe_cmd(sc, AXE_172_CMD_WRITE_IPG1, 0, sc->sc_ipgs[1], NULL); 1351 axe_cmd(sc, AXE_172_CMD_WRITE_IPG2, 0, sc->sc_ipgs[2], NULL); 1352 } 1353 1354 if (AXE_IS_178_FAMILY(sc)) { 1355 sc->sc_flags &= ~(AXE_FLAG_STD_FRAME | AXE_FLAG_CSUM_FRAME); 1356 if ((sc->sc_flags & AXE_FLAG_772B) != 0 && 1357 (ifp->if_capenable & IFCAP_RXCSUM) != 0) { 1358 sc->sc_lenmask = AXE_CSUM_HDR_LEN_MASK; 1359 sc->sc_flags |= AXE_FLAG_CSUM_FRAME; 1360 } else { 1361 sc->sc_lenmask = AXE_HDR_LEN_MASK; 1362 sc->sc_flags |= AXE_FLAG_STD_FRAME; 1363 } 1364 } 1365 1366 /* Configure TX/RX checksum offloading. */ 1367 axe_csum_cfg(ue); 1368 1369 if (sc->sc_flags & AXE_FLAG_772B) { 1370 /* AX88772B uses different maximum frame burst configuration. */ 1371 axe_cmd(sc, AXE_772B_CMD_RXCTL_WRITE_CFG, 1372 ax88772b_mfb_table[AX88772B_MFB_16K].threshold, 1373 ax88772b_mfb_table[AX88772B_MFB_16K].byte_cnt, NULL); 1374 } 1375 1376 /* Enable receiver, set RX mode. */ 1377 rxmode = (AXE_RXCMD_MULTICAST | AXE_RXCMD_ENABLE); 1378 if (AXE_IS_178_FAMILY(sc)) { 1379 if (sc->sc_flags & AXE_FLAG_772B) { 1380 /* 1381 * Select RX header format type 1. Aligning IP 1382 * header on 4 byte boundary is not needed when 1383 * checksum offloading feature is not used 1384 * because we always copy the received frame in 1385 * RX handler. When RX checksum offloading is 1386 * active, aligning IP header is required to 1387 * reflect actual frame length including RX 1388 * header size. 1389 */ 1390 rxmode |= AXE_772B_RXCMD_HDR_TYPE_1; 1391 if ((ifp->if_capenable & IFCAP_RXCSUM) != 0) 1392 rxmode |= AXE_772B_RXCMD_IPHDR_ALIGN; 1393 } else { 1394 /* 1395 * Default Rx buffer size is too small to get 1396 * maximum performance. 1397 */ 1398 rxmode |= AXE_178_RXCMD_MFB_16384; 1399 } 1400 } else { 1401 rxmode |= AXE_172_RXCMD_UNICAST; 1402 } 1403 1404 /* If we want promiscuous mode, set the allframes bit. */ 1405 if (ifp->if_flags & IFF_PROMISC) 1406 rxmode |= AXE_RXCMD_PROMISC; 1407 1408 if (ifp->if_flags & IFF_BROADCAST) 1409 rxmode |= AXE_RXCMD_BROADCAST; 1410 1411 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, rxmode, NULL); 1412 1413 /* Load the multicast filter. */ 1414 axe_setmulti(ue); 1415 1416 usbd_xfer_set_stall(sc->sc_xfer[AXE_BULK_DT_WR]); 1417 1418 ifp->if_drv_flags |= IFF_DRV_RUNNING; 1419 /* Switch to selected media. */ 1420 axe_ifmedia_upd(ifp); 1421 } 1422 1423 static void 1424 axe_setpromisc(struct usb_ether *ue) 1425 { 1426 struct axe_softc *sc = uether_getsc(ue); 1427 struct ifnet *ifp = uether_getifp(ue); 1428 uint16_t rxmode; 1429 1430 axe_cmd(sc, AXE_CMD_RXCTL_READ, 0, 0, &rxmode); 1431 1432 rxmode = le16toh(rxmode); 1433 1434 if (ifp->if_flags & IFF_PROMISC) { 1435 rxmode |= AXE_RXCMD_PROMISC; 1436 } else { 1437 rxmode &= ~AXE_RXCMD_PROMISC; 1438 } 1439 1440 axe_cmd(sc, AXE_CMD_RXCTL_WRITE, 0, rxmode, NULL); 1441 1442 axe_setmulti(ue); 1443 } 1444 1445 static void 1446 axe_stop(struct usb_ether *ue) 1447 { 1448 struct axe_softc *sc = uether_getsc(ue); 1449 struct ifnet *ifp = uether_getifp(ue); 1450 1451 AXE_LOCK_ASSERT(sc, MA_OWNED); 1452 1453 ifp->if_drv_flags &= ~(IFF_DRV_RUNNING | IFF_DRV_OACTIVE); 1454 sc->sc_flags &= ~AXE_FLAG_LINK; 1455 1456 /* 1457 * stop all the transfers, if not already stopped: 1458 */ 1459 usbd_transfer_stop(sc->sc_xfer[AXE_BULK_DT_WR]); 1460 usbd_transfer_stop(sc->sc_xfer[AXE_BULK_DT_RD]); 1461 } 1462 1463 static int 1464 axe_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data) 1465 { 1466 struct usb_ether *ue = ifp->if_softc; 1467 struct axe_softc *sc; 1468 struct ifreq *ifr; 1469 int error, mask, reinit; 1470 1471 sc = uether_getsc(ue); 1472 ifr = (struct ifreq *)data; 1473 error = 0; 1474 reinit = 0; 1475 if (cmd == SIOCSIFCAP) { 1476 AXE_LOCK(sc); 1477 mask = ifr->ifr_reqcap ^ ifp->if_capenable; 1478 if ((mask & IFCAP_TXCSUM) != 0 && 1479 (ifp->if_capabilities & IFCAP_TXCSUM) != 0) { 1480 ifp->if_capenable ^= IFCAP_TXCSUM; 1481 if ((ifp->if_capenable & IFCAP_TXCSUM) != 0) 1482 ifp->if_hwassist |= AXE_CSUM_FEATURES; 1483 else 1484 ifp->if_hwassist &= ~AXE_CSUM_FEATURES; 1485 reinit++; 1486 } 1487 if ((mask & IFCAP_RXCSUM) != 0 && 1488 (ifp->if_capabilities & IFCAP_RXCSUM) != 0) { 1489 ifp->if_capenable ^= IFCAP_RXCSUM; 1490 reinit++; 1491 } 1492 if (reinit > 0 && ifp->if_drv_flags & IFF_DRV_RUNNING) 1493 ifp->if_drv_flags &= ~IFF_DRV_RUNNING; 1494 else 1495 reinit = 0; 1496 AXE_UNLOCK(sc); 1497 if (reinit > 0) 1498 uether_init(ue); 1499 } else 1500 error = uether_ioctl(ifp, cmd, data); 1501 1502 return (error); 1503 } 1504