1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2# Copyright (c) 2020 MediaTek
3%YAML 1.2
4---
5$id: http://devicetree.org/schemas/usb/mediatek,mtk-xhci.yaml#
6$schema: http://devicetree.org/meta-schemas/core.yaml#
7
8title: MediaTek USB3 xHCI
9
10maintainers:
11  - Chunfeng Yun <chunfeng.yun@mediatek.com>
12
13allOf:
14  - $ref: usb-xhci.yaml
15
16description: |
17  There are two scenarios:
18  case 1: only supports xHCI driver;
19  case 2: supports dual-role mode, and the host is based on xHCI driver.
20
21properties:
22  # common properties for both case 1 and case 2
23  compatible:
24    items:
25      - enum:
26          - mediatek,mt2701-xhci
27          - mediatek,mt2712-xhci
28          - mediatek,mt7622-xhci
29          - mediatek,mt7623-xhci
30          - mediatek,mt7629-xhci
31          - mediatek,mt7986-xhci
32          - mediatek,mt8173-xhci
33          - mediatek,mt8183-xhci
34          - mediatek,mt8186-xhci
35          - mediatek,mt8188-xhci
36          - mediatek,mt8192-xhci
37          - mediatek,mt8195-xhci
38          - mediatek,mt8365-xhci
39      - const: mediatek,mtk-xhci
40
41  reg:
42    minItems: 1
43    items:
44      - description: the registers of xHCI MAC
45      - description: the registers of IP Port Control
46
47  reg-names:
48    minItems: 1
49    items:
50      - const: mac
51      - const: ippc  # optional, only needed for case 1.
52
53  interrupts:
54    description:
55      use "interrupts-extended" when the interrupts are connected to the
56      separate interrupt controllers
57    minItems: 1
58    items:
59      - description: xHCI host controller interrupt
60      - description: optional, wakeup interrupt used to support runtime PM
61
62  interrupt-names:
63    minItems: 1
64    items:
65      - const: host
66      - const: wakeup
67
68  power-domains:
69    description: A phandle to USB power domain node to control USB's MTCMOS
70    maxItems: 1
71
72  clocks:
73    minItems: 1
74    items:
75      - description: Controller clock used by normal mode
76      - description: Reference clock used by low power mode etc
77      - description: Mcu bus clock for register access
78      - description: DMA bus clock for data transfer
79      - description: controller clock
80      - description: frame count clock
81
82  clock-names:
83    minItems: 1
84    items:
85      - const: sys_ck  # required, the following ones are optional
86      - const: ref_ck
87      - const: mcu_ck
88      - const: dma_ck
89      - const: xhci_ck
90      - const: frmcnt_ck
91
92  phys:
93    description:
94      List of all PHYs used on this HCD, it's better to keep PHYs in order
95      as the hardware layout
96    minItems: 1
97    items:
98      - description: USB2/HS PHY    # required, others are optional
99      - description: USB3/SS(P) PHY
100      - description: USB2/HS PHY
101      - description: USB3/SS(P) PHY
102      - description: USB2/HS PHY
103      - description: USB3/SS(P) PHY
104      - description: USB2/HS PHY
105      - description: USB3/SS(P) PHY
106      - description: USB2/HS PHY
107
108  vusb33-supply:
109    description: Regulator of USB AVDD3.3v
110
111  vbus-supply:
112    description: Regulator of USB VBUS5v
113
114  resets:
115    maxItems: 1
116
117  usb3-lpm-capable: true
118
119  usb2-lpm-disable: true
120
121  imod-interval-ns:
122    description:
123      Interrupt moderation interval value, it is 8 times as much as that
124      defined in the xHCI spec on MTK's controller.
125    default: 5000
126
127  rx-fifo-depth:
128    $ref: /schemas/types.yaml#/definitions/uint32
129    description:
130      It is a quirk used to work around Gen1 isoc-in endpoint transfer issue
131      that still send out unexpected ACK after device finishes the burst
132      transfer with a short packet and cause an exception, specially on a 4K
133      camera device, it happens on controller before about IPM v1.6.0;
134      the side-effect is that it may cause performance drop about 10%,
135      including bulk transfer, prefer to use 3k here. The size is in bytes.
136    enum: [1024, 2048, 3072, 4096]
137
138  # the following properties are only used for case 1
139  wakeup-source:
140    description: enable USB remote wakeup, see power/wakeup-source.txt
141    type: boolean
142
143  mediatek,syscon-wakeup:
144    $ref: /schemas/types.yaml#/definitions/phandle-array
145    maxItems: 1
146    description:
147      A phandle to syscon used to access the register of the USB wakeup glue
148      layer between xHCI and SPM, the field should always be 3 cells long.
149    items:
150      items:
151        - description:
152            The first cell represents a phandle to syscon
153        - description:
154            The second cell represents the register base address of the glue
155            layer in syscon
156        - description: |
157            The third cell represents the hardware version of the glue layer,
158            1 - used by mt8173 etc, revision 1 without following IPM rule;
159            2 - used by mt2712 etc, revision 2 following IPM rule;
160            101 - used by mt8183, specific 1.01;
161            102 - used by mt8192, specific 1.02;
162            103 - used by mt8195, IP0, specific 1.03;
163            104 - used by mt8195, IP1, specific 1.04;
164            105 - used by mt8195, IP2, specific 1.05;
165            106 - used by mt8195, IP3, specific 1.06;
166          enum: [1, 2, 101, 102, 103, 104, 105, 106]
167
168  mediatek,u3p-dis-msk:
169    $ref: /schemas/types.yaml#/definitions/uint32
170    description: The mask to disable u3ports, bit0 for u3port0,
171      bit1 for u3port1, ... etc
172
173  mediatek,u2p-dis-msk:
174    $ref: /schemas/types.yaml#/definitions/uint32
175    description: The mask to disable u2ports, bit0 for u2port0,
176      bit1 for u2port1, ... etc
177
178  "#address-cells":
179    const: 1
180
181  "#size-cells":
182    const: 0
183
184patternProperties:
185  "@[0-9a-f]{1}$":
186    type: object
187    description: The hard wired USB devices.
188
189dependencies:
190  wakeup-source: [ 'mediatek,syscon-wakeup' ]
191
192required:
193  - compatible
194  - reg
195  - reg-names
196  - interrupts
197  - clocks
198  - clock-names
199
200additionalProperties: false
201
202examples:
203  - |
204    #include <dt-bindings/clock/mt8173-clk.h>
205    #include <dt-bindings/interrupt-controller/arm-gic.h>
206    #include <dt-bindings/interrupt-controller/irq.h>
207    #include <dt-bindings/phy/phy.h>
208    #include <dt-bindings/power/mt8173-power.h>
209
210    usb@11270000 {
211        compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci";
212        reg = <0x11270000 0x1000>, <0x11280700 0x0100>;
213        reg-names = "mac", "ippc";
214        interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
215        power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
216        clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
217        clock-names = "sys_ck", "ref_ck";
218        phys = <&u3port0 PHY_TYPE_USB3>, <&u2port1 PHY_TYPE_USB2>;
219        vusb33-supply = <&mt6397_vusb_reg>;
220        vbus-supply = <&usb_p1_vbus>;
221        imod-interval-ns = <10000>;
222        mediatek,syscon-wakeup = <&pericfg 0x400 1>;
223        wakeup-source;
224        usb3-lpm-capable;
225    };
226...
227