1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Device Tree Source for the Lager board
4 *
5 * Copyright (C) 2013-2014 Renesas Solutions Corp.
6 * Copyright (C) 2014 Cogent Embedded, Inc.
7 * Copyright (C) 2015-2016 Renesas Electronics Corporation
8 */
9
10/*
11 * SSI-AK4643
12 *
13 * SW1: 1: AK4643
14 *      2: CN22
15 *      3: ADV7511
16 *
17 * This command is required when Playback/Capture
18 *
19 *	amixer set "LINEOUT Mixer DACL" on
20 *	amixer set "DVC Out" 100%
21 *	amixer set "DVC In" 100%
22 *
23 * You can use Mute
24 *
25 *	amixer set "DVC Out Mute" on
26 *	amixer set "DVC In Mute" on
27 *
28 * You can use Volume Ramp
29 *
30 *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
31 *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
32 *	amixer set "DVC Out Ramp" on
33 *	aplay xxx.wav &
34 *	amixer set "DVC Out"  80%  // Volume Down
35 *	amixer set "DVC Out" 100%  // Volume Up
36 */
37
38/dts-v1/;
39#include "r8a7790.dtsi"
40#include <dt-bindings/gpio/gpio.h>
41#include <dt-bindings/input/input.h>
42
43/ {
44	model = "Lager";
45	compatible = "renesas,lager", "renesas,r8a7790";
46
47	aliases {
48		serial0 = &scif0;
49		serial1 = &scifa1;
50		i2c8 = &gpioi2c1;
51		i2c9 = &gpioi2c2;
52		i2c10 = &i2cexio0;
53		i2c11 = &i2cexio1;
54		i2c12 = &i2chdmi;
55		i2c13 = &i2cpwr;
56		mmc0 = &mmcif1;
57		mmc1 = &sdhi0;
58		mmc2 = &sdhi2;
59	};
60
61	chosen {
62		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
63		stdout-path = "serial0:115200n8";
64	};
65
66	memory@40000000 {
67		device_type = "memory";
68		reg = <0 0x40000000 0 0x40000000>;
69	};
70
71	memory@140000000 {
72		device_type = "memory";
73		reg = <1 0x40000000 0 0xc0000000>;
74	};
75
76	keyboard {
77		compatible = "gpio-keys";
78
79		pinctrl-0 = <&keyboard_pins>;
80		pinctrl-names = "default";
81
82		one {
83			linux,code = <KEY_1>;
84			label = "SW2-1";
85			wakeup-source;
86			debounce-interval = <20>;
87			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
88		};
89		two {
90			linux,code = <KEY_2>;
91			label = "SW2-2";
92			wakeup-source;
93			debounce-interval = <20>;
94			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
95		};
96		three {
97			linux,code = <KEY_3>;
98			label = "SW2-3";
99			wakeup-source;
100			debounce-interval = <20>;
101			gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
102		};
103		four {
104			linux,code = <KEY_4>;
105			label = "SW2-4";
106			wakeup-source;
107			debounce-interval = <20>;
108			gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
109		};
110	};
111
112	leds {
113		compatible = "gpio-leds";
114		led6 {
115			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
116		};
117		led7 {
118			gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
119		};
120		led8 {
121			gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
122		};
123	};
124
125	fixedregulator1v8: regulator-1v8 {
126		compatible = "regulator-fixed";
127		regulator-name = "fixed-1.8V";
128		regulator-min-microvolt = <1800000>;
129		regulator-max-microvolt = <1800000>;
130		regulator-boot-on;
131		regulator-always-on;
132	};
133
134	fixedregulator3v3: regulator-3v3 {
135		compatible = "regulator-fixed";
136		regulator-name = "fixed-3.3V";
137		regulator-min-microvolt = <3300000>;
138		regulator-max-microvolt = <3300000>;
139		regulator-boot-on;
140		regulator-always-on;
141	};
142
143	vcc_sdhi0: regulator-vcc-sdhi0 {
144		compatible = "regulator-fixed";
145
146		regulator-name = "SDHI0 Vcc";
147		regulator-min-microvolt = <3300000>;
148		regulator-max-microvolt = <3300000>;
149
150		gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
151		enable-active-high;
152	};
153
154	vccq_sdhi0: regulator-vccq-sdhi0 {
155		compatible = "regulator-gpio";
156
157		regulator-name = "SDHI0 VccQ";
158		regulator-min-microvolt = <1800000>;
159		regulator-max-microvolt = <3300000>;
160
161		gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
162		gpios-states = <1>;
163		states = <3300000 1>, <1800000 0>;
164	};
165
166	vcc_sdhi2: regulator-vcc-sdhi2 {
167		compatible = "regulator-fixed";
168
169		regulator-name = "SDHI2 Vcc";
170		regulator-min-microvolt = <3300000>;
171		regulator-max-microvolt = <3300000>;
172
173		gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
174		enable-active-high;
175	};
176
177	vccq_sdhi2: regulator-vccq-sdhi2 {
178		compatible = "regulator-gpio";
179
180		regulator-name = "SDHI2 VccQ";
181		regulator-min-microvolt = <1800000>;
182		regulator-max-microvolt = <3300000>;
183
184		gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
185		gpios-states = <1>;
186		states = <3300000 1>, <1800000 0>;
187	};
188
189	audio_clock: audio_clock {
190		compatible = "fixed-clock";
191		#clock-cells = <0>;
192		clock-frequency = <11289600>;
193	};
194
195	rsnd_ak4643: sound {
196		compatible = "simple-audio-card";
197
198		simple-audio-card,format = "left_j";
199		simple-audio-card,bitclock-master = <&sndcodec>;
200		simple-audio-card,frame-master = <&sndcodec>;
201
202		sndcpu: simple-audio-card,cpu {
203			sound-dai = <&rcar_sound>;
204		};
205
206		sndcodec: simple-audio-card,codec {
207			sound-dai = <&ak4643>;
208			clocks = <&audio_clock>;
209		};
210	};
211
212	vga-encoder {
213		compatible = "adi,adv7123";
214
215		ports {
216			#address-cells = <1>;
217			#size-cells = <0>;
218
219			port@0 {
220				reg = <0>;
221				adv7123_in: endpoint {
222					remote-endpoint = <&du_out_rgb>;
223				};
224			};
225			port@1 {
226				reg = <1>;
227				adv7123_out: endpoint {
228					remote-endpoint = <&vga_in>;
229				};
230			};
231		};
232	};
233
234	vga {
235		compatible = "vga-connector";
236
237		port {
238			vga_in: endpoint {
239				remote-endpoint = <&adv7123_out>;
240			};
241		};
242	};
243
244	hdmi-in {
245		compatible = "hdmi-connector";
246		type = "a";
247
248		port {
249			hdmi_con_in: endpoint {
250				remote-endpoint = <&adv7612_in>;
251			};
252		};
253	};
254
255	cec_clock: cec-clock {
256		compatible = "fixed-clock";
257		#clock-cells = <0>;
258		clock-frequency = <12000000>;
259	};
260
261	hdmi-out {
262		compatible = "hdmi-connector";
263		type = "a";
264
265		port {
266			hdmi_con_out: endpoint {
267				remote-endpoint = <&adv7511_out>;
268			};
269		};
270	};
271
272	x2_clk: x2-clock {
273		compatible = "fixed-clock";
274		#clock-cells = <0>;
275		clock-frequency = <148500000>;
276	};
277
278	x13_clk: x13-clock {
279		compatible = "fixed-clock";
280		#clock-cells = <0>;
281		clock-frequency = <148500000>;
282	};
283
284	gpioi2c1: i2c-8 {
285		#address-cells = <1>;
286		#size-cells = <0>;
287		compatible = "i2c-gpio";
288		status = "disabled";
289		scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
290		sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
291		i2c-gpio,delay-us = <5>;
292	};
293
294	gpioi2c2: i2c-9 {
295		#address-cells = <1>;
296		#size-cells = <0>;
297		compatible = "i2c-gpio";
298		status = "disabled";
299		scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
300		sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
301		i2c-gpio,delay-us = <5>;
302	};
303
304	/*
305	 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
306	 * We use the I2C demuxer, so the desired IP core can be selected at runtime
307	 * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
308	 * Note: For testing the I2C slave feature, it is convenient to connect this
309	 * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
310	 * instantiate the slave device at runtime according to the documentation.
311	 * You can then communicate with the slave via IIC3.
312	 *
313	 * IIC0/I2C0 does not appear to support fallback to GPIO.
314	 */
315	i2cexio0: i2c-mux1 {
316		compatible = "i2c-demux-pinctrl";
317		i2c-parent = <&iic0>, <&i2c0>;
318		i2c-bus-name = "i2c-exio0";
319		#address-cells = <1>;
320		#size-cells = <0>;
321	};
322
323	/*
324	 * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
325	 * This is similar to the arangement described for i2cexio0 (above)
326	 * with a fallback to GPIO also provided.
327	 */
328	i2cexio1: i2c-mux2 {
329		compatible = "i2c-demux-pinctrl";
330		i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
331		i2c-bus-name = "i2c-exio1";
332		#address-cells = <1>;
333		#size-cells = <0>;
334	};
335
336	/*
337	 * IIC2 and I2C2 may be switched using pinmux.
338	 * A fallback to GPIO is also provided.
339	 */
340	i2chdmi: i2c-mux3 {
341		compatible = "i2c-demux-pinctrl";
342		i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
343		i2c-bus-name = "i2c-hdmi";
344		#address-cells = <1>;
345		#size-cells = <0>;
346
347		ak4643: codec@12 {
348			compatible = "asahi-kasei,ak4643";
349			#sound-dai-cells = <0>;
350			reg = <0x12>;
351		};
352
353		composite-in@20 {
354			compatible = "adi,adv7180";
355			reg = <0x20>;
356
357			port {
358				adv7180: endpoint {
359					bus-width = <8>;
360					remote-endpoint = <&vin1ep0>;
361				};
362			};
363		};
364
365		hdmi@39 {
366			compatible = "adi,adv7511w";
367			reg = <0x39>;
368			interrupt-parent = <&gpio1>;
369			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
370			clocks = <&cec_clock>;
371			clock-names = "cec";
372
373			avdd-supply = <&fixedregulator1v8>;
374			dvdd-supply = <&fixedregulator1v8>;
375			pvdd-supply = <&fixedregulator1v8>;
376			dvdd-3v-supply = <&fixedregulator3v3>;
377			bgvdd-supply = <&fixedregulator1v8>;
378
379			adi,input-depth = <8>;
380			adi,input-colorspace = "rgb";
381			adi,input-clock = "1x";
382
383			ports {
384				#address-cells = <1>;
385				#size-cells = <0>;
386
387				port@0 {
388					reg = <0>;
389					adv7511_in: endpoint {
390						remote-endpoint = <&lvds0_out>;
391					};
392				};
393
394				port@1 {
395					reg = <1>;
396					adv7511_out: endpoint {
397						remote-endpoint = <&hdmi_con_out>;
398					};
399				};
400			};
401		};
402
403		hdmi-in@4c {
404			compatible = "adi,adv7612";
405			reg = <0x4c>;
406			interrupt-parent = <&gpio1>;
407			interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
408			default-input = <0>;
409
410			ports {
411				#address-cells = <1>;
412				#size-cells = <0>;
413
414				port@0 {
415					reg = <0>;
416					adv7612_in: endpoint {
417						remote-endpoint = <&hdmi_con_in>;
418					};
419				};
420
421				port@2 {
422					reg = <2>;
423					adv7612_out: endpoint {
424						remote-endpoint = <&vin0ep2>;
425					};
426				};
427			};
428		};
429	};
430
431	/*
432	 * IIC3 and I2C3 may be switched using pinmux.
433	 * IIC3/I2C3 does not appear to support fallback to GPIO.
434	 */
435	i2cpwr: i2c-mux4 {
436		compatible = "i2c-demux-pinctrl";
437		pinctrl-names = "default";
438		pinctrl-0 = <&pmic_irq_pins>;
439		i2c-parent = <&iic3>, <&i2c3>;
440		i2c-bus-name = "i2c-pwr";
441		#address-cells = <1>;
442		#size-cells = <0>;
443
444		pmic@58 {
445			compatible = "dlg,da9063";
446			reg = <0x58>;
447			interrupt-parent = <&irqc0>;
448			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
449			interrupt-controller;
450
451			rtc {
452				compatible = "dlg,da9063-rtc";
453			};
454
455			watchdog {
456				compatible = "dlg,da9063-watchdog";
457			};
458		};
459
460		vdd_dvfs: regulator@68 {
461			compatible = "dlg,da9210";
462			reg = <0x68>;
463			interrupt-parent = <&irqc0>;
464			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
465
466			regulator-min-microvolt = <1000000>;
467			regulator-max-microvolt = <1000000>;
468			regulator-boot-on;
469			regulator-always-on;
470		};
471	};
472};
473
474&du {
475	pinctrl-0 = <&du_pins>;
476	pinctrl-names = "default";
477	status = "okay";
478
479	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
480		 <&x13_clk>, <&x2_clk>;
481	clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
482
483	ports {
484		port@0 {
485			endpoint {
486				remote-endpoint = <&adv7123_in>;
487			};
488		};
489	};
490};
491
492&lvds0 {
493	status = "okay";
494
495	ports {
496		port@1 {
497			endpoint {
498				remote-endpoint = <&adv7511_in>;
499			};
500		};
501	};
502};
503
504&lvds1 {
505	ports {
506		port@1 {
507			lvds_connector: endpoint {
508			};
509		};
510	};
511};
512
513&extal_clk {
514	clock-frequency = <20000000>;
515};
516
517&pfc {
518	pinctrl-0 = <&scif_clk_pins>;
519	pinctrl-names = "default";
520
521	du_pins: du {
522		groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
523		function = "du";
524	};
525
526	scif0_pins: scif0 {
527		groups = "scif0_data";
528		function = "scif0";
529	};
530
531	scif_clk_pins: scif_clk {
532		groups = "scif_clk";
533		function = "scif_clk";
534	};
535
536	ether_pins: ether {
537		groups = "eth_link", "eth_mdio", "eth_rmii";
538		function = "eth";
539	};
540
541	phy1_pins: phy1 {
542		groups = "intc_irq0";
543		function = "intc";
544	};
545
546	scifa1_pins: scifa1 {
547		groups = "scifa1_data";
548		function = "scifa1";
549	};
550
551	sdhi0_pins: sd0 {
552		groups = "sdhi0_data4", "sdhi0_ctrl";
553		function = "sdhi0";
554		power-source = <3300>;
555	};
556
557	sdhi0_pins_uhs: sd0_uhs {
558		groups = "sdhi0_data4", "sdhi0_ctrl";
559		function = "sdhi0";
560		power-source = <1800>;
561	};
562
563	sdhi2_pins: sd2 {
564		groups = "sdhi2_data4", "sdhi2_ctrl";
565		function = "sdhi2";
566		power-source = <3300>;
567	};
568
569	sdhi2_pins_uhs: sd2_uhs {
570		groups = "sdhi2_data4", "sdhi2_ctrl";
571		function = "sdhi2";
572		power-source = <1800>;
573	};
574
575	mmc1_pins: mmc1 {
576		groups = "mmc1_data8", "mmc1_ctrl";
577		function = "mmc1";
578	};
579
580	qspi_pins: qspi {
581		groups = "qspi_ctrl", "qspi_data4";
582		function = "qspi";
583	};
584
585	msiof1_pins: msiof1 {
586		groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
587				 "msiof1_tx";
588		function = "msiof1";
589	};
590
591	i2c0_pins: i2c0 {
592		groups = "i2c0";
593		function = "i2c0";
594	};
595
596	iic0_pins: iic0 {
597		groups = "iic0";
598		function = "iic0";
599	};
600
601	i2c1_pins: i2c1 {
602		groups = "i2c1";
603		function = "i2c1";
604	};
605
606	iic1_pins: iic1 {
607		groups = "iic1";
608		function = "iic1";
609	};
610
611	i2c2_pins: i2c2 {
612		groups = "i2c2";
613		function = "i2c2";
614	};
615
616	iic2_pins: iic2 {
617		groups = "iic2";
618		function = "iic2";
619	};
620
621	i2c3_pins: i2c3 {
622		groups = "i2c3";
623		function = "i2c3";
624	};
625
626	iic3_pins: iic3 {
627		groups = "iic3";
628		function = "iic3";
629	};
630
631	pmic_irq_pins: pmicirq {
632		groups = "intc_irq2";
633		function = "intc";
634	};
635
636	hsusb_pins: hsusb {
637		groups = "usb0_ovc_vbus";
638		function = "usb0";
639	};
640
641	usb0_pins: usb0 {
642		groups = "usb0";
643		function = "usb0";
644	};
645
646	usb1_pins: usb1 {
647		groups = "usb1";
648		function = "usb1";
649	};
650
651	usb2_pins: usb2 {
652		groups = "usb2";
653		function = "usb2";
654	};
655
656	vin0_pins: vin0 {
657		groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
658		function = "vin0";
659	};
660
661	vin1_pins: vin1 {
662		groups = "vin1_data8", "vin1_clk";
663		function = "vin1";
664	};
665
666	sound_pins: sound {
667		groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
668		function = "ssi";
669	};
670
671	sound_clk_pins: sound_clk {
672		groups = "audio_clk_a";
673		function = "audio_clk";
674	};
675
676	keyboard_pins: keyboard {
677		pins = "GP_1_14", "GP_1_24", "GP_1_26", "GP_1_28";
678		bias-pull-up;
679	};
680};
681
682&ether {
683	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
684	pinctrl-names = "default";
685
686	phy-handle = <&phy1>;
687	renesas,ether-link-active-low;
688	status = "okay";
689
690	phy1: ethernet-phy@1 {
691		compatible = "ethernet-phy-id0022.1537",
692			     "ethernet-phy-ieee802.3-c22";
693		reg = <1>;
694		interrupt-parent = <&irqc0>;
695		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
696		micrel,led-mode = <1>;
697		reset-gpios = <&gpio5 31 GPIO_ACTIVE_LOW>;
698	};
699};
700
701&cmt0 {
702	status = "okay";
703};
704
705&mmcif1 {
706	pinctrl-0 = <&mmc1_pins>;
707	pinctrl-names = "default";
708
709	vmmc-supply = <&fixedregulator3v3>;
710	bus-width = <8>;
711	non-removable;
712	status = "okay";
713};
714
715&sata1 {
716	status = "okay";
717};
718
719&qspi {
720	pinctrl-0 = <&qspi_pins>;
721	pinctrl-names = "default";
722
723	status = "okay";
724
725	flash: flash@0 {
726		compatible = "spansion,s25fl512s", "jedec,spi-nor";
727		reg = <0>;
728		spi-max-frequency = <30000000>;
729		spi-tx-bus-width = <4>;
730		spi-rx-bus-width = <4>;
731		spi-cpha;
732		spi-cpol;
733		m25p,fast-read;
734
735		partitions {
736			compatible = "fixed-partitions";
737			#address-cells = <1>;
738			#size-cells = <1>;
739
740			partition@0 {
741				label = "loader";
742				reg = <0x00000000 0x00040000>;
743				read-only;
744			};
745			partition@40000 {
746				label = "user";
747				reg = <0x00040000 0x00400000>;
748				read-only;
749			};
750			partition@440000 {
751				label = "flash";
752				reg = <0x00440000 0x03bc0000>;
753			};
754		};
755	};
756};
757
758&scif0 {
759	pinctrl-0 = <&scif0_pins>;
760	pinctrl-names = "default";
761
762	status = "okay";
763};
764
765&scifa1 {
766	pinctrl-0 = <&scifa1_pins>;
767	pinctrl-names = "default";
768
769	status = "okay";
770};
771
772&scif_clk {
773	clock-frequency = <14745600>;
774};
775
776&msiof1 {
777	pinctrl-0 = <&msiof1_pins>;
778	pinctrl-names = "default";
779
780	status = "okay";
781
782	pmic: pmic@0 {
783		compatible = "renesas,r2a11302ft";
784		reg = <0>;
785		spi-max-frequency = <6000000>;
786		spi-cpol;
787		spi-cpha;
788	};
789};
790
791&sdhi0 {
792	pinctrl-0 = <&sdhi0_pins>;
793	pinctrl-1 = <&sdhi0_pins_uhs>;
794	pinctrl-names = "default", "state_uhs";
795
796	vmmc-supply = <&vcc_sdhi0>;
797	vqmmc-supply = <&vccq_sdhi0>;
798	cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
799	sd-uhs-sdr50;
800	sd-uhs-sdr104;
801	status = "okay";
802};
803
804&sdhi2 {
805	pinctrl-0 = <&sdhi2_pins>;
806	pinctrl-1 = <&sdhi2_pins_uhs>;
807	pinctrl-names = "default", "state_uhs";
808
809	vmmc-supply = <&vcc_sdhi2>;
810	vqmmc-supply = <&vccq_sdhi2>;
811	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
812	sd-uhs-sdr50;
813	status = "okay";
814};
815
816&cpu0 {
817	cpu0-supply = <&vdd_dvfs>;
818};
819
820&i2c0	{
821	pinctrl-0 = <&i2c0_pins>;
822	pinctrl-names = "i2c-exio0";
823};
824
825&iic0	{
826	pinctrl-0 = <&iic0_pins>;
827	pinctrl-names = "i2c-exio0";
828};
829
830&i2c1	{
831	pinctrl-0 = <&i2c1_pins>;
832	pinctrl-names = "i2c-exio1";
833};
834
835&iic1	{
836	pinctrl-0 = <&iic1_pins>;
837	pinctrl-names = "i2c-exio1";
838};
839
840&i2c2	{
841	pinctrl-0 = <&i2c2_pins>;
842	pinctrl-names = "i2c-hdmi";
843
844	clock-frequency = <100000>;
845};
846
847&iic2	{
848	pinctrl-0 = <&iic2_pins>;
849	pinctrl-names = "i2c-hdmi";
850
851	clock-frequency = <100000>;
852};
853
854&i2c3	{
855	pinctrl-0 = <&i2c3_pins>;
856	pinctrl-names = "i2c-pwr";
857};
858
859&iic3	{
860	pinctrl-0 = <&iic3_pins>;
861	pinctrl-names = "i2c-pwr";
862};
863
864&pci0 {
865	status = "okay";
866	pinctrl-0 = <&usb0_pins>;
867	pinctrl-names = "default";
868};
869
870&pci1 {
871	status = "okay";
872	pinctrl-0 = <&usb1_pins>;
873	pinctrl-names = "default";
874};
875
876&xhci {
877	status = "okay";
878	pinctrl-0 = <&usb2_pins>;
879	pinctrl-names = "default";
880};
881
882&pci2 {
883	status = "okay";
884	pinctrl-0 = <&usb2_pins>;
885	pinctrl-names = "default";
886};
887
888&hsusb {
889	status = "okay";
890	pinctrl-0 = <&hsusb_pins>;
891	pinctrl-names = "default";
892	renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
893};
894
895&usbphy {
896	status = "okay";
897};
898
899/* HDMI video input */
900&vin0 {
901	pinctrl-0 = <&vin0_pins>;
902	pinctrl-names = "default";
903
904	status = "okay";
905
906	port {
907		vin0ep2: endpoint {
908			remote-endpoint = <&adv7612_out>;
909			bus-width = <24>;
910			hsync-active = <0>;
911			vsync-active = <0>;
912			pclk-sample = <1>;
913			data-active = <1>;
914		};
915	};
916};
917
918/* composite video input */
919&vin1 {
920	pinctrl-0 = <&vin1_pins>;
921	pinctrl-names = "default";
922
923	status = "okay";
924
925	port {
926		vin1ep0: endpoint {
927			remote-endpoint = <&adv7180>;
928			bus-width = <8>;
929		};
930	};
931};
932
933&rcar_sound {
934	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
935	pinctrl-names = "default";
936
937	/* Single DAI */
938	#sound-dai-cells = <0>;
939
940	status = "okay";
941
942	rcar_sound,dai {
943		dai0 {
944			playback = <&ssi0>, <&src2>, <&dvc0>;
945			capture  = <&ssi1>, <&src3>, <&dvc1>;
946		};
947	};
948};
949
950&rwdt {
951	timeout-sec = <60>;
952	status = "okay";
953};
954
955&ssi1 {
956	shared-pin;
957};
958