1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Device Tree file for Marvell Armada 3720 development board
4 * (DB-88F3720-DDR3)
5 * Copyright (C) 2016 Marvell
6 *
7 * Gregory CLEMENT <gregory.clement@free-electrons.com>
8 *
9 * This file is compatible with the version 1.4 and the version 2.0 of
10 * the board, however the CON numbers are different between the 2
11 * version
12 */
13
14/dts-v1/;
15
16#include <dt-bindings/gpio/gpio.h>
17#include "armada-372x.dtsi"
18
19/ {
20	model = "Marvell Armada 3720 Development Board DB-88F3720-DDR3";
21	compatible = "marvell,armada-3720-db", "marvell,armada3720", "marvell,armada3710";
22
23	chosen {
24		stdout-path = "serial0:115200n8";
25	};
26
27	memory@0 {
28		device_type = "memory";
29		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
30	};
31
32	exp_usb3_vbus: usb3-vbus {
33		compatible = "regulator-fixed";
34		regulator-name = "usb3-vbus";
35		regulator-min-microvolt = <5000000>;
36		regulator-max-microvolt = <5000000>;
37		enable-active-high;
38		regulator-always-on;
39		gpio = <&gpio_exp 1 GPIO_ACTIVE_HIGH>;
40	};
41
42	usb3_phy: usb3-phy {
43		compatible = "usb-nop-xceiv";
44		vcc-supply = <&exp_usb3_vbus>;
45	};
46
47	vcc_sd_reg1: regulator {
48		compatible = "regulator-gpio";
49		regulator-name = "vcc_sd1";
50		regulator-min-microvolt = <1800000>;
51		regulator-max-microvolt = <3300000>;
52		regulator-boot-on;
53
54		gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>;
55		gpios-states = <0>;
56		states = <1800000 0x1
57			  3300000 0x0>;
58		enable-active-high;
59	};
60
61	vcc_sd_reg2: regulator-vmcc {
62		compatible = "regulator-fixed";
63		regulator-name = "vcc_sd2";
64		regulator-min-microvolt = <3300000>;
65		regulator-max-microvolt = <3300000>;
66		regulator-boot-on;
67		enable-active-high;
68		gpio = <&gpio_exp 4 GPIO_ACTIVE_HIGH>;
69	};
70};
71
72/* Gigabit module on CON19(V2.0)/CON21(V1.4) */
73&eth0 {
74	pinctrl-names = "default";
75	pinctrl-0 = <&rgmii_pins>;
76	phy-mode = "rgmii-id";
77	phy = <&phy0>;
78	status = "okay";
79};
80
81/* Gigabit module on CON18(V2.0)/CON20(V1.4) */
82&eth1 {
83	phy-mode = "sgmii";
84	phy = <&phy1>;
85	status = "okay";
86};
87
88&i2c0 {
89	pinctrl-names = "default";
90	pinctrl-0 = <&i2c1_pins>;
91	status = "okay";
92
93	gpio_exp: pca9555@22 {
94		compatible = "nxp,pca9555";
95		gpio-controller;
96		#gpio-cells = <2>;
97
98		reg = <0x22>;
99		/*
100		 * IO0_0: PWR_EN_USB2	IO1_0: PWR_EN_VTT
101		 * IO0_1: PWR_EN_USB23	IO1_1: MPCIE_WDISABLE
102		 * IO0_2: PWR_EN_SATA	IO1_2: RGMII_DEV_RSTN
103		 * IO0_3: PWR_EN_PCIE	IO1_3: SGMII_DEV_RSTN
104		 * IO0_4: PWR_EN_SD
105		 * IO0_5: PWR_EN_EMMC
106		 * IO0_6: PWR_EN_RGMII	IO1_6: SATA_USB3.0_SEL
107		 * IO0_7: PWR_EN_SGMII	IO1_7: PWR_MCI_PS
108		 */
109	};
110
111	rtc@68  {
112		/* PT7C4337A from pericom fully compatible with the ds1337 */
113		compatible = "dallas,ds1337";
114		reg = <0x68>;
115	};
116};
117
118&mdio {
119	status = "okay";
120	phy0: ethernet-phy@0 {
121		reg = <0>;
122	};
123
124	phy1: ethernet-phy@1 {
125		reg = <1>;
126	};
127};
128
129/* CON15(V2.0)/CON17(V1.4) : PCIe / CON15(V2.0)/CON12(V1.4) :mini-PCIe */
130&pcie0 {
131	pinctrl-names = "default";
132	pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
133	reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
134	status = "okay";
135};
136
137/* CON3 */
138&sata {
139	status = "okay";
140};
141
142&sdhci0 {
143	non-removable;
144	bus-width = <8>;
145	mmc-ddr-1_8v;
146	mmc-hs400-1_8v;
147	marvell,pad-type = "fixed-1-8v";
148	status = "okay";
149};
150
151/* SD slot module on CON14(V2.0)/CON15(V1.4) */
152&sdhci1 {
153	wp-inverted;
154	cd-gpios = <&gpiosb 2 GPIO_ACTIVE_LOW>;
155	bus-width = <4>;
156	marvell,pad-type = "sd";
157	vqmmc-supply = <&vcc_sd_reg1>;
158	vmmc-supply = <&vcc_sd_reg2>;
159	status = "okay";
160};
161
162&spi0 {
163	status = "okay";
164	pinctrl-names = "default";
165	pinctrl-0 = <&spi_quad_pins>;
166
167	flash@0 {
168		compatible = "jedec,spi-nor";
169		reg = <0>;
170		spi-max-frequency = <108000000>;
171		spi-rx-bus-width = <4>;
172		spi-tx-bus-width = <4>;
173
174		partitions {
175			compatible = "fixed-partitions";
176			#address-cells = <1>;
177			#size-cells = <1>;
178			partition@0 {
179				label = "bootloader";
180				reg = <0x0 0x200000>;
181			};
182			partition@200000 {
183				label = "U-boot Env";
184				reg = <0x200000 0x10000>;
185			};
186			partition@210000 {
187				label = "Linux";
188				reg = <0x210000 0xDF0000>;
189			};
190		};
191	};
192};
193
194/*
195 * Exported on the micro USB connector CON30(V2.0)/CON32(V1.4) through
196 * an FTDI (also on CON24(V2.0)/CON26(V1.4)).
197 */
198&uart0 {
199	pinctrl-names = "default";
200	pinctrl-0 = <&uart1_pins>;
201	status = "okay";
202};
203
204/* CON26(V2.0)/CON28(V1.4) */
205&uart1 {
206	pinctrl-names = "default";
207	pinctrl-0 = <&uart2_pins>;
208	status = "okay";
209};
210
211/* CON27(V2.0)/CON29(V1.4) */
212&usb2 {
213	status = "okay";
214};
215
216/* CON29(V2.0)/CON31(V1.4) */
217&usb3 {
218	status = "okay";
219	usb-phy = <&usb3_phy>;
220};
221